If release is part of frontend ops then it is called in the
course of dvb_frontend_detach. The process also decrements
the module usage count. The problem is if the lgdt3306a
driver is reached via i2c_new_device, then when it is
eventually destroyed remove is called, which further
decrements the module usage count to negative. After this
occurs the driver is in a bad state and no longer works.
Also fixed by NULLing out the release callback is a double
kfree of state, which introduces arbitrary oopses/GPF.
This problem is only currently reachable via the em28xx driver.
On disconnect of Hauppauge SoloHD before:
lsmod | grep lgdt3306a
lgdt3306a 28672 -1
i2c_mux 16384 1 lgdt3306a
On disconnect of Hauppauge SoloHD after:
lsmod | grep lgdt3306a
lgdt3306a 28672 0
i2c_mux 16384 1 lgdt3306a
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add a missing device to the driver table.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Reviewed-by: Michael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add additional pids to driver list
Signed-off-by: Brad Love <brad@nextdimension.cc>
Reviewed-by: Michael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Maximum 4 em28xx boards is too low, this can be maxed out by two devices.
This allows all the dvb adapters in the system to be em28xx if so desired.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Reviewed-by: Michael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Hauppauge em28xx bulk devices exhibit continuity errors and corrupted
packets, when run in VMWare virtual machines. Unknown if other
manufacturers bulk models exhibit the same issue. KVM/Qemu is unaffected.
According to documentation the maximum packet multiplier for em28xx in bulk
transfer mode is 256 * 188 bytes. This changes the size of bulk transfers
to maximum supported value and have a bonus beneficial alignment.
Before:
After:
This sets up USB to expect just as many bytes as the em28xx is set to emit.
Successful usage under load afterwards natively and in both VMWare
and KVM/Qemu virtual machines.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Reviewed-by: Michael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Set appropriate bulk/ISOC transfer multiplier on capture start.
This sets ISOC transfer to USB endpoint configuration
This sets bulk transfer to 48128 bytes (188 * 256)
The bulk multiplier is maximum allowed according to Empia.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
em28xx_duplicate_dev() is static. This were supposed to be
merged on the last patch, but somehow, I forgot "-a" when
I called git commit --amend.
Fixes: be7fd3c3a8 ("media: em28xx: Hauppauge DualHD second tuner functionality")
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Implement use of secondary TS port on em28xx.
Adds has_dual_ts field, allows secondary demod/tuner to be
added to a single em28xx device.
Hauppauge DualHD models are configured to use this feature.
[mchehab@s-opensource.com: em28xx_duplicate_dev() should be static]
Signed-off-by: Brad Love <brad@nextdimension.cc>
Reviewed-by: Michael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Replace usages of the locally defined ABS() macro with calls to the
canonical abs() from kernel.h and remove the old definitions of ABS()
This change was originally motivated by two local definitions of the
ABS (absolute value) macro that fail to parenthesize their parameter
properly. This can lead to a bad expansion for low-precedence
expression arguments.
For example: ABS(1-2) currently expands to ((1-2) < 0 ? (-1-2) : (1-2))
which evaluates to -3. But the correct expansion would be
((1-2) < 0 ? -(1-2) : (1-2)) which evaluates to 1.
Signed-off-by: Dan Gopstein <dgopstein@nyu.edu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The MaxLinear MxL5xx has support for physical layer scrambling, which was
recently added to the DVB core via the new scrambling_sequence_index
property. Add required bits to the mxl5xx driver.
Picked up from dddvb master, commit 5c032058b9ba ("add support for PLS")
by Ralph Metzler <rjkm@metzlerbros.de>, adapted to the different naming
of the pls property (pls vs. scrambling_sequence_index).
Cc: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
* commit 'v4.16-rc4~0': (900 commits)
Linux 4.16-rc4
memremap: fix softlockup reports at teardown
libnvdimm: re-enable deep flush for pmem devices via fsync()
MAINTAINERS: take over Kconfig maintainership
vfio: disable filesystem-dax page pinning
kconfig: fix line number in recursive inclusion error message
Coccinelle: memdup: Fix typo in warning messages
i2c: octeon: Prevent error message on bus error
parisc: Reduce irq overhead when run in qemu
parisc: Use cr16 interval timers unconditionally on qemu
parisc: Check if secondary CPUs want own PDC calls
parisc: Hide virtual kernel memory layout
parisc: Fix ordering of cache and TLB flushes
kconfig: Update ncurses package names for menuconfig
kbuild/kallsyms: trivial typo fix
kbuild: test --build-id linker flag by ld-option instead of cc-ldoption
kbuild: drop superfluous GCC_PLUGINS_CFLAGS assignment
kconfig: Don't leak choice names during parsing
sh: fix build error for empty CONFIG_BUILTIN_DTB_SOURCE
kconfig: set SYMBOL_AUTO to the symbol marked with defconfig_list
...
Pull x86 fixes from Thomas Gleixner:
"A small set of fixes for x86:
- Add missing instruction suffixes to assembly code so it can be
compiled by newer GAS versions without warnings.
- Switch refcount WARN exceptions to UD2 as we did in general
- Make the reboot on Intel Edison platforms work
- A small documentation update so text and sample command match"
* 'x86/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
Documentation, x86, resctrl: Make text and sample command match
x86/platform/intel-mid: Handle Intel Edison reboot correctly
x86/asm: Add instruction suffixes to bitops
x86/entry/64: Add instruction suffix
x86/refcounts: Switch to UD2 for exceptions
Pull x86/pti fixes from Thomas Gleixner:
"Three fixes related to melted spectrum:
- Sync the cpu_entry_area page table to initial_page_table on 32 bit.
Otherwise suspend/resume fails because resume uses
initial_page_table and triggers a triple fault when accessing the
cpu entry area.
- Zero the SPEC_CTL MRS on XEN before suspend to address a
shortcoming in the hypervisor.
- Fix another switch table detection issue in objtool"
* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/cpu_entry_area: Sync cpu_entry_area to initial_page_table
objtool: Fix another switch table detection issue
x86/xen: Zero MSR_IA32_SPEC_CTRL before suspend
Pull timer fixes from Thomas Gleixner:
"A small set of fixes from the timer departement:
- Add a missing timer wheel clock forward when migrating timers off a
unplugged CPU to prevent operating on a stale clock base and
missing timer deadlines.
- Use the proper shift count to extract data from a register value to
prevent evaluating unrelated bits
- Make the error return check in the FSL timer driver work correctly.
Checking an unsigned variable for less than zero does not really
work well.
- Clarify the confusing comments in the ARC timer code"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timers: Forward timer base before migrating timers
clocksource/drivers/arc_timer: Update some comments
clocksource/drivers/mips-gic-timer: Use correct shift count to extract data
clocksource/drivers/fsl_ftm_timer: Fix error return checking
Pull irq fixlet from Thomas Gleixner:
"Just a documentation update for the missing device tree property of
the R-Car M3N interrupt controller"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
dt-bindings/irqchip/renesas-irqc: Document R-Car M3-N support
-----BEGIN PGP SIGNATURE-----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=bF96
-----END PGP SIGNATURE-----
Merge tag 'for-4.16-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
- when NR_CPUS is large, a SRCU structure can significantly inflate
size of the main filesystem structure that would not be possible to
allocate by kmalloc, so the kvalloc fallback is used
- improved error handling
- fix endiannes when printing some filesystem attributes via sysfs,
this is could happen when a filesystem is moved between different
endianity hosts
- send fixes: the NO_HOLE mode should not send a write operation for a
file hole
- fix log replay for for special files followed by file hardlinks
- fix log replay failure after unlink and link combination
- fix max chunk size calculation for DUP allocation
* tag 'for-4.16-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
Btrfs: fix log replay failure after unlink and link combination
Btrfs: fix log replay failure after linking special file and fsync
Btrfs: send, fix issuing write op when processing hole in no data mode
btrfs: use proper endianness accessors for super_copy
btrfs: alloc_chunk: fix DUP stripe size handling
btrfs: Handle btrfs_set_extent_delalloc failure in relocate_file_extent_cluster
btrfs: handle failure of add_pending_csums
btrfs: use kvzalloc to allocate btrfs_fs_info
Pull i2c fixes from Wolfram Sang:
"A driver fix and a documentation fix (which makes dependency handling
for the next cycle easier)"
* 'i2c/for-current-fixed' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: octeon: Prevent error message on bus error
dt-bindings: at24: sort manufacturers alphabetically
Pull libnvdimm fixes from Dan Williams:
"A 4.16 regression fix, three fixes for -stable, and a cleanup fix:
- During the merge window support for the new ACPI NVDIMM Platform
Capabilities structure disabled support for "deep flush", a
force-unit- access like mechanism for persistent memory. Restore
that mechanism.
- VFIO like RDMA is yet one more memory registration / pinning
interface that is incompatible with Filesystem-DAX. Disable long
term pins of Filesystem-DAX mappings via VFIO.
- The Filesystem-DAX detection to prevent long terms pins mistakenly
also disabled Device-DAX pins which are not subject to the same
block- map collision concerns.
- Similar to the setup path, softlockup warnings can trigger in the
shutdown path for large persistent memory namespaces. Teach
for_each_device_pfn() to perform cond_resched() in all cases.
- Boaz noticed that the might_sleep() in dax_direct_access() is stale
as of the v4.15 kernel.
These have received a build success notification from the 0day robot,
and the longterm pin fixes have appeared in -next. However, I recently
rebased the tree to remove some other fixes that need to be reworked
after review feedback.
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
memremap: fix softlockup reports at teardown
libnvdimm: re-enable deep flush for pmem devices via fsync()
vfio: disable filesystem-dax page pinning
dax: fix vma_is_fsdax() helper
dax: ->direct_access does not sleep anymore
- suppress sparse warnings about unknown attributes
- fix typos and stale comments
- fix build error of arch/sh
- fix wrong use of ld-option vs cc-ldoption
- remove redundant GCC_PLUGINS_CFLAGS assignment
- fix another memory leak of Kconfig
- fix line number in error messages of Kconfig
- do not write confusing CONFIG_DEFCONFIG_LIST out to .config
- add xstrdup() to Kconfig to handle memory shortage errors
- show also a Debian package name if ncurses is missing
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=sr4l
-----END PGP SIGNATURE-----
Merge tag 'kbuild-fixes-v4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- suppress sparse warnings about unknown attributes
- fix typos and stale comments
- fix build error of arch/sh
- fix wrong use of ld-option vs cc-ldoption
- remove redundant GCC_PLUGINS_CFLAGS assignment
- fix another memory leak of Kconfig
- fix line number in error messages of Kconfig
- do not write confusing CONFIG_DEFCONFIG_LIST out to .config
- add xstrdup() to Kconfig to handle memory shortage errors
- show also a Debian package name if ncurses is missing
* tag 'kbuild-fixes-v4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
MAINTAINERS: take over Kconfig maintainership
kconfig: fix line number in recursive inclusion error message
Coccinelle: memdup: Fix typo in warning messages
kconfig: Update ncurses package names for menuconfig
kbuild/kallsyms: trivial typo fix
kbuild: test --build-id linker flag by ld-option instead of cc-ldoption
kbuild: drop superfluous GCC_PLUGINS_CFLAGS assignment
kconfig: Don't leak choice names during parsing
sh: fix build error for empty CONFIG_BUILTIN_DTB_SOURCE
kconfig: set SYMBOL_AUTO to the symbol marked with defconfig_list
kconfig: add xstrdup() helper
kbuild: disable sparse warnings about unknown attributes
Makefile: Fix lying comment re. silentoldconfig
-----BEGIN PGP SIGNATURE-----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=ypdv
-----END PGP SIGNATURE-----
Merge tag 'media/v4.16-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
- some build fixes with randconfigs
- an m88ds3103 fix to prevent an OOPS if the chip doesn't provide the
right version during probe (with can happen if the hardware hangs)
- a potential out of array bounds reference in tvp5150
- some fixes and improvements in the DVB memory mapped API (added for
kernel 4.16)
* tag 'media/v4.16-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: vb2: Makefile: place vb2-trace together with vb2-core
media: Don't let tvp5150_get_vbi() go out of vbi_ram_default array
media: dvb: update buffer mmaped flags and frame counter
media: dvb: add continuity error indicators for memory mapped buffers
media: dmxdev: Fix the logic that enables DMA mmap support
media: dmxdev: fix error code for invalid ioctls
media: m88ds3103: don't call a non-initalized function
media: au0828: add VIDEO_V4L2 dependency
media: dvb: fix DVB_MMAP dependency
media: dvb: fix DVB_MMAP symbol name
media: videobuf2: fix build issues with vb2-trace
media: videobuf2: Add VIDEOBUF2_V4L2 Kconfig option for VB2 V4L2 part
x86:
- fix NULL dereference when using userspace lapic
- optimize spectre v1 mitigations by allowing guests to use LFENCE
- make microcode revision configurable to prevent guests from
unnecessarily blacklisting spectre v2 mitigation features
-----BEGIN PGP SIGNATURE-----
iQEcBAABCAAGBQJambvzAAoJEED/6hsPKofo9HwH/2il8xNSLIYf9pJtxZo/puyQ
ZSwByGdeLKBZ1GP1dhdZ8kMk3eBoci0a/sQJmhDiEG6GDf1Mrgri/xj3p60sWwXT
iReG+ZhBKg4QMj/IgOJQrh+53JT73QQP14wIhzc/DSi0Fo0ziqDA/lINxqMKc7oF
b5qratjsb4xF1db4d1g8Ii1VRk64UoBEVpEoP37OOyAu1rgXgDr+9C832KkP0rb+
pVYT8hLFiaYiwVN+WN52/NrIkqBlMvMp3ouRtMAajCQ9OznnraDJE6eTkPGDSDBM
RizSuQbev5R7pcmzCAP9/XKfTbeSUZQei2ZFXQXAOvIXMrQd/ITjbPvnObsceSE=
=wtQd
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Radim Krčmář:
"x86:
- fix NULL dereference when using userspace lapic
- optimize spectre v1 mitigations by allowing guests to use LFENCE
- make microcode revision configurable to prevent guests from
unnecessarily blacklisting spectre v2 mitigation feature"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: fix vcpu initialization with userspace lapic
KVM: X86: Allow userspace to define the microcode version
KVM: X86: Introduce kvm_get_msr_feature()
KVM: SVM: Add MSR-based feature support for serializing LFENCE
KVM: x86: Add a framework for supporting MSR-based features
The cond_resched() currently in the setup path needs to be duplicated in
the teardown path. Rather than require each instance of
for_each_device_pfn() to open code the same sequence, embed it in the
helper.
Link: https://github.com/intel/ixpdimm_sw/issues/11
Cc: "Jérôme Glisse" <jglisse@redhat.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: <stable@vger.kernel.org>
Fixes: 7138970383 ("mm, zone_device: Replace {get, put}_zone_device_page()...")
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Re-enable deep flush so that users always have a way to be sure that a
write makes it all the way out to media. Writes from the PMEM driver
always arrive at the NVDIMM since movnt is used to bypass the cache, and
the driver relies on the ADR (Asynchronous DRAM Refresh) mechanism to
flush write buffers on power failure. The Deep Flush mechanism is there
to explicitly write buffers to protect against (rare) ADR failure. This
change prevents a regression in deep flush behavior so that applications
can continue to depend on fsync() as a mechanism to trigger deep flush
in the filesystem-DAX case.
Fixes: 06e8ccdab1 ("acpi: nfit: Add support for detect platform CPU cache...")
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
I have recently picked up Kconfig patches to my tree without any
declaration. Making it official now.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Filesystem-DAX is incompatible with 'longterm' page pinning. Without
page cache indirection a DAX mapping maps filesystem blocks directly.
This means that the filesystem must not modify a file's block map while
any page in a mapping is pinned. In order to prevent the situation of
userspace holding of filesystem operations indefinitely, disallow
'longterm' Filesystem-DAX mappings.
RDMA has the same conflict and the plan there is to add a 'with lease'
mechanism to allow the kernel to notify userspace that the mapping is
being torn down for block-map maintenance. Perhaps something similar can
be put in place for vfio.
Note that xfs and ext4 still report:
"DAX enabled. Warning: EXPERIMENTAL, use at your own risk"
...at mount time, and resolving the dax-dma-vs-truncate problem is one
of the last hurdles to remove that designation.
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: kvm@vger.kernel.org
Cc: <stable@vger.kernel.org>
Reported-by: Haozhong Zhang <haozhong.zhang@intel.com>
Tested-by: Haozhong Zhang <haozhong.zhang@intel.com>
Fixes: d475c6346a ("dax,ext2: replace XIP read and write with DAX I/O")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
-----BEGIN PGP SIGNATURE-----
iQJIBAABCgAyFiEEgMe7l+5h9hnxdsnuWYigwDrT+vwFAlqZy4cUHGJoZWxnYWFz
QGdvb2dsZS5jb20ACgkQWYigwDrT+vzyuw/+M3EDZaGd0SMj5k47qll1udstDEBL
/WkCVTgrVov4TqMh+x5Pba7Yd+/2vFeIx2QbruYS7uGF8YwXMtET6+RJg+vUUMkW
ryIMKl0QRb9X11qJr5GtgOqij//wtV8BXPimGczB02d8ganJFhbxrJSx87z1lshm
g0u5ZNupddMHfT3JW0H4c2AFrkW9+KXjosShPuVzQbkhXxMAk+zbnuC6wRd1+GJV
4BewJMHLNFTg4cEz7O8ao7fRyYsHsaV65HdFoTlSGPrv3PEGZTqapmF9ATbEJTQd
CNQ0QMN+ewFMwZh17oCs0eEkoSLeyzMFVUfXs4IIpMRTxyJbLzuqwlU5VaCtXdkT
ntlETQ09MmNqvyusAmKvrqBjjw2clgvO7NCjJhaMY1ehOH6sEcbvOx83xp6P1RUc
mTqOVV7TbSXyyRFOEa6KunyC2tKmV+t2Cl4dOxVKwaja5J/Eh8GhGlM/r7qt4pEa
h3roNNE1VilHYR/8VcpCVydyueruaMSNrHzlhmIQw+UcsMDzEjBKzuxGFUYNU+0H
2wXZacv2MaDj3qndh8ZS9IHWW1bw6PMBCdf13HOPdEs9DjHX5uI1RsB49Z6rSM75
xXoiB/MHlK/3YgZNB2eEBQjFHfMDD1ylwsnIbeIMhvk074rE8d56C8uNXuBvYYPn
dakUdnUB8abeeD0=
=0inR
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.16-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
- Update pci.ids location (documentation only) (Randy Dunlap)
- Fix a crash when BIOS didn't assign a BAR and we try to enlarge it
(Christian König)
* tag 'pci-v4.16-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Allow release of resources that were never assigned
PCI: Update location of pci.ids file
Pull parisc fixes from Helge Deller:
- a patch to change the ordering of cache and TLB flushes to hopefully
fix the random segfaults we very rarely face (by Dave Anglin).
- a patch to hide the virtual kernel memory layout due to security
reasons.
- two small patches to make the kernel run more smoothly under qemu.
* 'parisc-4.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Reduce irq overhead when run in qemu
parisc: Use cr16 interval timers unconditionally on qemu
parisc: Check if secondary CPUs want own PDC calls
parisc: Hide virtual kernel memory layout
parisc: Fix ordering of cache and TLB flushes
delayed and three error path memory leak fixups from Chengguang.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABCAAGBQJamV3qAAoJEEp/3jgCEfOLv6kIAI0RXShR20dz9M3GnL2bDws7
KFkC/aNwbviXMAih3q7Q7ZiwXv6BI/uUK0YIYG/tWZoNHucYGS8ZOFDikdiIMcJR
2VP8Yas1/NvnLlh0ut45s2imvbXinkHcjWOLqgJJmJ2cEP9Ar/mbwz//TgfVMdNm
TSHEm2LPRge9jK3Ab/ZiatExGH6dx5hRJvssSauF+f2iN+q4nKj2aBqle+FKaNWT
Iv0ONi2f7aXnaXRvum4Y1gnKWXzKSFd8Y2Cr5R3tfTrKBv8nmQz54eRsMnnuxK/7
uV6Ujch4LUXBI1etXLqTwRdZQIcw3Li5PYxGrO8fl8mQfJau9yv5REw/rbgB5FU=
=f8gA
-----END PGP SIGNATURE-----
Merge tag 'ceph-for-4.16-rc4' of git://github.com/ceph/ceph-client
Pull ceph fixes from Ilya Dryomov:
"A cap handling fix from Zhi that ensures that metadata writeback isn't
delayed and three error path memory leak fixups from Chengguang"
* tag 'ceph-for-4.16-rc4' of git://github.com/ceph/ceph-client:
ceph: fix potential memory leak in init_caches()
ceph: fix dentry leak when failing to init debugfs
libceph, ceph: avoid memory leak when specifying same option several times
ceph: flush dirty caps of unlinked inode ASAP
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=AMhV
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20180302' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"A collection of fixes for this series. This is a little larger than
usual at this time, but that's mainly because I was out on vacation
last week. Nothing in here is major in any way, it's just two weeks of
fixes. This contains:
- NVMe pull from Keith, with a set of fixes from the usual suspects.
- mq-deadline zone unlock fix from Damien, fixing an issue with the
SMR zone locking added for 4.16.
- two bcache fixes sent in by Michael, with changes from Coly and
Tang.
- comment typo fix from Eric for blktrace.
- return-value error handling fix for nbd, from Gustavo.
- fix a direct-io case where we don't defer to a completion handler,
making us sleep from IRQ device completion. From Jan.
- a small series from Jan fixing up holes around handling of bdev
references.
- small set of regression fixes from Jiufei, mostly fixing problems
around the gendisk pointer -> partition index change.
- regression fix from Ming, fixing a boundary issue with the discard
page cache invalidation.
- two-patch series from Ming, fixing both a core blk-mq-sched and
kyber issue around token freeing on a requeue condition"
* tag 'for-linus-20180302' of git://git.kernel.dk/linux-block: (24 commits)
block: fix a typo
block: display the correct diskname for bio
block: fix the count of PGPGOUT for WRITE_SAME
mq-deadline: Make sure to always unlock zones
nvmet: fix PSDT field check in command format
nvme-multipath: fix sysfs dangerously created links
nbd: fix return value in error handling path
bcache: fix kcrashes with fio in RAID5 backend dev
bcache: correct flash only vols (check all uuids)
blktrace_api.h: fix comment for struct blk_user_trace_setup
blockdev: Avoid two active bdev inodes for one device
genhd: Fix BUG in blkdev_open()
genhd: Fix use after free in __blkdev_get()
genhd: Add helper put_disk_and_module()
genhd: Rename get_disk() to get_disk_and_module()
genhd: Fix leaked module reference for NVME devices
direct-io: Fix sleep in atomic due to sync AIO
nvme-pci: Fix nvme queue cleanup if IRQ setup fails
block: kyber: fix domain token leak during requeue
blk-mq: don't call io sched's .requeue_request when requeueing rq to ->dispatch
...
- Make the task scheduler load and utilization signals be
frequency-invariant again after recent changes in the SCPI
cpufreq driver (Dietmar Eggemann).
- Drop an unnecessary leftover Kconfig dependency from the SCPI
cpufreq driver (Sudeep Holla).
- Fix the initialization of the s3c24xx cpufreq driver (Viresh
Kumar).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=AMSC
-----END PGP SIGNATURE-----
Merge tag 'pm-4.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix three issues in cpufreq drivers: one recent regression, one
leftover Kconfig dependency and one old but "stable" material.
Specifics:
- Make the task scheduler load and utilization signals be
frequency-invariant again after recent changes in the SCPI cpufreq
driver (Dietmar Eggemann).
- Drop an unnecessary leftover Kconfig dependency from the SCPI
cpufreq driver (Sudeep Holla).
- Fix the initialization of the s3c24xx cpufreq driver (Viresh
Kumar)"
* tag 'pm-4.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: s3c24xx: Fix broken s3c_cpufreq_init()
cpufreq: scpi: Fix incorrect arm_big_little config dependency
cpufreq: scpi: invoke frequency-invariance setter function
When recursive inclusion is detected, the line number of the last
'included from:' is wrong.
[Test Case]
Kconfig:
-------->8--------
source "Kconfig2"
-------->8--------
Kconfig2:
-------->8--------
source "Kconfig3"
-------->8--------
Kconfig3:
-------->8--------
source "Kconfig"
-------->8--------
[Result]
$ make allyesconfig
scripts/kconfig/conf --allyesconfig Kconfig
Kconfig:1: recursive inclusion detected. Inclusion path:
current file : 'Kconfig'
included from: 'Kconfig3:1'
included from: 'Kconfig2:1'
included from: 'Kconfig:3'
scripts/kconfig/Makefile:89: recipe for target 'allyesconfig' failed
make[1]: *** [allyesconfig] Error 1
Makefile:512: recipe for target 'allyesconfig' failed
make: *** [allyesconfig] Error 2
where we expect
current file : 'Kconfig'
included from: 'Kconfig3:1'
included from: 'Kconfig2:1'
included from: 'Kconfig:1'
The 'iter->lineno+1' in the second fpinrtf() should be 'iter->lineno-1'.
I refactored the code to merge the two fprintf() calls.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Ulf Magnusson <ulfalizer@gmail.com>
The error message:
[Fri Feb 16 13:42:13 2018] i2c-thunderx 0000:01:09.4: unhandled state: 0
is mis-leading as state 0 (bus error) is not an unknown state.
Return -EIO as before but avoid printing the message. Also rename
STAT_ERROR to STATE_BUS_ERROR.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEFp3rbAvDxGAT0sefEacuoBRx13IFAlqZErcACgkQEacuoBRx
13JCFg/9Ej3CNc0eHYN1mSfA+fGV59M6m5foSJw1eiZRrOYZJYEB+Bmcg8deJaWS
9tV3QBl8RCtIVTpwXEYR6PBn56H7dxm5P+o1497LyAcB/RR7CqVLHPWaBjR83xUR
0qucZTC0SZmCTMWOaqAVKmPBeoEhyJKgVd0cK7AHwE/nWBQl2DC9oWI/AKqows7e
HjBgeUAF7S/lq2v2jtKv9WLTqyVNVCSELnuFAQsDhaemVfc9TzoCcaXkbPxNp4fb
/VZb3FWlrdZjFyNF7U6qMlzWYwpxTcCWNvJvynoXfBMk73/YDQRzclm/57AvpTEa
pJOwq3srtFEMTZGetkwyofn04TE37a2GjyRT2C43dyZGZV4xHX48V9lEgnTuashR
7bbisQ+dzavyYbLCSH8kx3PjmU/iSL8RAWCjuVXB7rWIQLVqEG8mo2DTJGZdsN/9
9cFr0aFgBcQhozXBwS/Gwu7FXv0n6v9vsGFv+Tr/UmURCKweW/HsfkFpU9nkLIyU
VZo4/lu+TBeQGI3pSu8aPp45kIh49xzyhy23AcifeUs69BFl2aB5fM1i0IzIcDfc
HWB5ZMOy2So7nZZ0u+gxaC0olh7BuVh74xpDJZNLyPUQtfqilJ8OaXnv/2vdXTkP
A9hIhm34C03OOG/nKuOKD2wWFFYls1VNPxBSKMnmHtLaUsPzRis=
=vIz0
-----END PGP SIGNATURE-----
Merge tag 'at24-4.16-rc4-for-wolfram' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into i2c/for-current
Pull in this fixup to get rid of a dependency for the next cycle:
"- sort the manufacturers in DT bindings alphabetically"
When run under QEMU, calling mfctl(16) creates some overhead because the
qemu timer has to be scaled and moved into the register. This patch
reduces the number of calls to mfctl(16) by moving the calls out of the
loops.
Additionally, increase the minimal time interval to 8000 cycles instead
of 500 to compensate possible QEMU delays when delivering interrupts.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # 4.14+
When running on qemu we know that the (emulated) cr16 cpu-internal
clocks are syncronized. So let's use them unconditionally on qemu.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # 4.14+
The architecture specification says (for 64-bit systems): PDC is a per
processor resource, and operating system software must be prepared to
manage separate pointers to PDCE_PROC for each processor. The address
of PDCE_PROC for the monarch processor is stored in the Page Zero
location MEM_PDC. The address of PDCE_PROC for each non-monarch
processor is passed in gr26 when PDCE_RESET invokes OS_RENDEZ.
Currently we still use one PDC for all CPUs, but in case we face a
machine which is following the specification let's warn about it.
Signed-off-by: Helge Deller <deller@gmx.de>
The change to flush_kernel_vmap_range() wasn't sufficient to avoid the
SMP stalls. The problem is some drivers call these routines with
interrupts disabled. Interrupts need to be enabled for flush_tlb_all()
and flush_cache_all() to work. This version adds checks to ensure
interrupts are not disabled before calling routines that need IPI
interrupts. When interrupts are disabled, we now drop into slower code.
The attached change fixes the ordering of cache and TLB flushes in
several cases. When we flush the cache using the existing PTE/TLB
entries, we need to flush the TLB after doing the cache flush. We don't
need to do this when we flush the entire instruction and data caches as
these flushes don't use the existing TLB entries. The same is true for
tmpalias region flushes.
The flush_kernel_vmap_range() and invalidate_kernel_vmap_range()
routines have been updated.
Secondly, we added a new purge_kernel_dcache_range_asm() routine to
pacache.S and use it in invalidate_kernel_vmap_range(). Nominally,
purges are faster than flushes as the cache lines don't have to be
written back to memory.
Hopefully, this is sufficient to resolve the remaining problems due to
cache speculation. So far, testing indicates that this is the case. I
did work up a patch using tmpalias flushes, but there is a performance
hit because we need the physical address for each page, and we also need
to sequence access to the tmpalias flush code. This increases the
probability of stalls.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: stable@vger.kernel.org # 4.9+
Signed-off-by: Helge Deller <deller@gmx.de>
The package name is ncurses-devel for Redhat based distros
and libncurses-dev for Debian based distros.
Signed-off-by: Arvind Prasanna <arvindprasanna@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
'--build-id' is passed to $(LD), so it should be tested by 'ld-option'.
This seems a kind of misconversion when ld-option was renamed to
cc-ldoption.
Commit f86fd30660 ("kbuild: rename ld-option to cc-ldoption") renamed
all instances of 'ld-option' to 'cc-ldoption'.
Then, commit 691ef3e7fd ("kbuild: introduce ld-option") re-added
'ld-option' as a new implementation.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
GCC_PLUGINS_CFLAGS is already in the environment, so it is superfluous
to add it in commandline of final build of init/.
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The named choice is not used in the kernel tree, but if it were used,
it would not be freed.
The intention of the named choice can be seen in the log of
commit 5a1aa8a1af ("kconfig: add named choice group").
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Ulf Magnusson <ulfalizer@gmail.com>
If CONFIG_USE_BUILTIN_DTB is enabled, but CONFIG_BUILTIN_DTB_SOURCE
is empty (for example, allmodconfig), it fails to build, like this:
make[2]: *** No rule to make target 'arch/sh/boot/dts/.dtb.o',
needed by 'arch/sh/boot/dts/built-in.o'. Stop.
Surround obj-y with ifneq ... endif.
I replaced $(CONFIG_USE_BUILTIN_DTB) with 'y' since this is always
the case from the following code from arch/sh/Makefile:
core-$(CONFIG_USE_BUILTIN_DTB) += arch/sh/boot/dts/
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Brad Love