When driver is unloaded, all sessions are torn down, all commmands are
flushed, chip is reset to ensure there is no knowledge of target mode in
ISP. The irq_cmd_count field was used to make sure all commands are
processed on top of that. The irq_cmd_count is now redundant and not
needed.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Accelerate generation of SCSI busy to let initiators slow down when
target is running low in resources.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Current code already destroy all target sessions when target Mode is
stopped. Target core would waits for all commands that belong to each
session to purge. The extra wait for interrupts to settle down is not
relevant.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Previously, the ql2xexchoffld module parameter was used to control the
max number of exchanges to be offload onto host memory.
Module parameter ql_dm_tgt_ex_pct was used to control the percentage of
exchanges allocated to the Target side.
With this patch, module parameter ql_dm_tgt_ex_pct is no longer used to
control exchanges for the driver. New module parameter ql2xiniexchg is
added to control exchanges between target mode and initiator mode.
With the updated module parameters, users can control the exact number
of exchanges for either Initiator or Target. The exchange offload
feature will be automatically enabled when the total number of exchanges
exceeds 2048 limit.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Tell FW to track exchange/cmd state to prevent driver from using stale
exchange or exchange that is not meant for this command.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Assign unique id to all traces and logs for debug purpose.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Name server login is normally handle by FW. In some rare case where one
of the switches is being updated, name server login could get
affected. Trigger relogin to name server when driver detects this
condition.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is already flag defined PFLG_DISCONNECTED, which is set
for PCI or register disconnect error condition. There is no need to have
flag PCI_ERR, which has same purpose. Remove use of PCI_ERR flag and use
PFLG_DISCONNECTED flag during error condition.
Signed-off-by: Sawan Chandak <sawan.chandak@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In case of hardware queue full, commands can loop between
TCM stack and tcm_qla2xx shim layers for retry. While command
is waiting for retry, task mgmt can get ahead and abort the
cmmand that encountered queue full condition. Fix this by
dropping the command, if task mgmt has already started the
command free process.
Acked-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If the port is moved/changed, current code would trigger
a deletion. If the port is already deleted, then do relogin.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Convert usage of spin_lock to spin_lock_irqsave because qla2xxx driver
can access all the data structures in an interrupt context.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver added mechanism to move ABTS/PUREX/RIDA mailbox to
ATIO queue as part of commit id 41dc529a46
("qla2xxx: Improve RSCN handling in driver").
This patch adds a check to only allow ABTS/PURX/RIDA
to be moved to ATIO Queue for ISP83XX and ISP27XX.
Cc: <stable@vger.kernel.org> # 4.11
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add the change_queue_depth member to our SCSI host template so the queue
depth of devices attached to qedf can be changed dynamically.
Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Increase the default number of commands that the driver tells the
SCSI mid-layer it can do to increase the default performance of the
driver.
Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Drop invalid or unexpected FCoE frames that come into the non-offload path
since the FCoE firmware would not do the filtering for us.
Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We need to add a bus reset no-op as without it some of the LUNs attached to a
vport may go offline when the error handler escalates to host reset due to not
having a bus reset handler in the driver. What happens is we escalate to host
reset which does a soft link down/link up to reset the adapter. However with
multiple vports attached it's been observed that if the vports do log back into
the target within 5 seconds, the SCSI layer offlines the devices most likely
due to a TUR timing out to verify that the device is online. Adding a bus
reset handler will cause the TUR to be sent after the bus reset handler where
the devices will still be online if the bus reset is initiated by sg_reset
(which is the case in the test that was failing). The bus reset will succeed
and not needlessly bring the device offline/online.
Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We should be using the same logic to do a soft reset of the FCoE function
whether it is initiated via sg_reset or the fc_host issue_lip attribute.
Refactor the host reset and fcoe reset handlers to use the preferred logic
which is currently contained in qedf_eh_host_reset().
Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reduce the logging level we set for qed messages pertaining to this PCI
function so that unnecessary messages are not printed in the kernel
message log.
Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Expose this information for interested applications.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If an fcport is not offloaded then the members of the qedf_rport struct
are undefined which may cause a system crash.
Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If there are multiple descriptors for a particular type in a clear virtual
link we receive, we will not process it correctly but rather take the last
value. This can cause us not to not flap the virtual link as the value from
the descriptors that we compare against the our stored FCF or fc_lport values
may not match.
Change this to do a comparison when processing the each descriptor instead of at
the end and then set a bool if we need to do the reset.
Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We need to check the return code the set_fp_int() callback in case we were
not allocated any fastpath interrupts or there was an error setting up the
fastpath interrupts from the qed perspective.
Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For libfc to register FDMI attributes we need to do two things:
- Set the appropriate fc_host attributes that libfc will use to form the
FDMI registration commands
- Set lport->fdmi_enabled to 1
Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
T6 FCoE support is added in fw version 1.16.45.0 so return error if fw
version < 1.16.45.0 for T6 adapters.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch removes an extra out label in _fcoe_create function where we
return if creation of FCOE interface is failed.
Signed-off-by: Milan P. Gandhi <mgandhi@redhat.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch does a cleanup and fixes few small typos in fcoe.c
Signed-off-by: Milan P. Gandhi <mgandhi@redhat.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Trivial fix to spelling mistake in debugfs message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
qla_tgt_cmd.free_work is not used by the qla2xxx driver. Hence remove
that member of struct qla_tgt_cmd.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Quinn Tran <quinn.tran@cavium.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: David Disseldorp <ddiss@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add null check before indirectly dereferencing pointer task->lldd_task
in statement u32 tag = slot->idx;
Addresses-Coverity-ID: 1373843
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The newly added suspend/resume support causes harmless warnings when
CONFIG_PM is disabled:
smartpqi/smartpqi_init.c:5147:12: error: 'pqi_ctrl_wait_for_pending_io' defined but not used [-Werror=unused-function]
smartpqi/smartpqi_init.c:2019:13: error: 'pqi_wait_until_lun_reset_finished' defined but not used [-Werror=unused-function]
smartpqi/smartpqi_init.c:2013:13: error: 'pqi_wait_until_scan_finished' defined but not used [-Werror=unused-function]
We can avoid the warnings by removing the #ifdef around the handlers and
instead marking them as __maybe_unused, which will let gcc drop the
unused code silently.
Fixes: f44d210312a6 ("scsi: smartpqi: add suspend and resume support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When copying attributes, the len argument was padded out and the
resulting memcpy() would copy beyond the end of the source buffer.
Avoid this, and use size_t for val_len to avoid all the casts.
Similarly, avoid source buffer casts and use void *.
Additionally enforces val_len can be represented by u16 and that the DMA
buffer was not overflowed. Fixes the size of mfa, which is not
FC_FDMI_PORT_ATTR_MAXFRAMESIZE_LEN (but it will be padded up to 4). This
was noticed by the future CONFIG_FORTIFY_SOURCE checks.
Cc: Daniel Micay <danielmicay@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In storvsc driver, inbound messages do not go through inbound lock. The
only effect of this lock was is to provide a barrier for connect and
remove logic.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In 4.12-rc1, new functions were added to support iterating over elements
in the vmbus event ring. This patch uses them to simplify the ring
buffer handling in virtual SCSI driver as well.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Enable probe for T6 adapters, add code to flash T6 firmware and firmware
config file, use T6 specific macros.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Gerry Morong <gerry.morong@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Instead of rewriting write/readq, use existing functions
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add module parameters to disable heartbeat support and to disable
shutting down the controller when a controller is taken offline.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Better initialization of linked list heads.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Display the RAID level via sysfs
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- make all references to RAID bypass consistent throughout driver.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Improved formatting of information displayed when devices
are added/removed from the system.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Increase the timeout on admin commands from 3 seconds to 60
seconds and added a check for controller crash in the loop
where the driver polls for admin command completion.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
enhance mapping of RAID path errors to Linux SCSI host
error codes.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- Improve controller branding support.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
improve support for taking controller offline.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- Improve handling of offline devices.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
set the internal flag that causes I/O to be sent down the
RAID path when the AIO path is disabled
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
add support for actions to take when controller goes offline.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
make the queue depth for LVs the same as the maximum
I/Os supported by the controller
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
constrain resource usage during kdump to avoid kdump failures
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
change return value for controller offline to be consistent
with the rest of the driver.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
add support for PTRAID devices
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- improve some error messages.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- remove debug code that is no longer necessary.
- Some WARN_ON checks were removed because the driver continues
to function when the conditions are met.
- remove a MACRO that is no longer used.
- remove unnecessary multi-line statements.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
correct the BMIC Identify Physical Device structure
- missing 2 fields
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
eliminate redundant error message during initialization
if the controller has crashed.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
make all variable names for pointers to struct pci_dev consistent
throughout the driver.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add check for controller lockup during waits for synchronous
controller commands.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
add workaround for BDMA hardware bug that can cause
hw to read up to 12 SGL elements (192 bytes) beyond the
last element in the list. This fix avoids IOMMU violations
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
check for controller lockups
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
add support for ACPI S3 (suspend) and S4 (hibernate)
system power states.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- Block all I/O targeted at LUN reset device.
- Wait until all I/O targeted at LUN reset device has been
consumed by the controller.
- Issue LUN reset request.
- Wait until all outstanding I/Os and LUN reset completion
have been received by the host.
- Return to OS results of LUN reset request.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Only register for controller events that driver supports
cleanup event handling.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
put in SIS mode during initialization.
support kexec/kdump
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
tell smartpqi controller to generate a checkpoint for rare lockup
conditions.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
add support for setting PCIe completion timeout.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
minor cleanup of interrupt initialization and tear-down.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
correct a problem caused by holding a spinlock during device deletion.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- simplify the driver
- there are a lot of quirky racy conditions not handled
- causes more aborts/resets when the number of commands to be aborted is
large, such as in multi-path fail-overs.
- has been turned off in our internal driver since 8/31/2015
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- Block I/O requests with 0 length transfers which go down the ioaccel
path. This causes lockup issues down in the basecode.
- These issues have been fixed, but there are customers who are
experiencing the issues when running older firmware.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
create new worker thread to monitor controller events
- both the rescan and event monitor workers can cause a rescan to occur
however for multipath we have found that we need to respond faster
than the normal scheduled rescan interval for path fail-overs.
- getting controller events only involves reading a register, but the
rescan worker can obtain an updated LUN list when there is a PTRAID
device present.
- move common code to a separate function.
advantages:
- detect controller events more frequently.
- leave rescan thread interval at 30 seconds.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- queue depth assignment not in correct place, had no effect.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- mark device state sooner.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- call scsi_done when the command completes.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- schedule another scan.
- mark current scan as completed.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Prevent enclosure resets.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.tell@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use the return from TUR as a check for the device state.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.tell@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
external shelves do not support BMICs.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- align with latest spec.
- added __attribute((aligned(512)))
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update the driver version to 50834
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: David Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove reference to Series-9 HBA and created arc ctrl check function.
Signed-off-by: Prasad B Munirathnam <prasad.munirathnam@microsemi.com>
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: David Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added info and error messages in controller reset function to log
information about the status of the IOP/SOFT reset.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: David Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Make sure that IOP and SOFT reset are enabled for both for both arc and
hba1000 controllers.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: David Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Made sure that ioctl commands return in case of a controller reset.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: Dave Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The command thread checks the ctrl health periodically before sending
updates to the controller. The function that it uses is aac_check_health
which does more than get the health status.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: David Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Removed switch case and replaced with if mask checks. Moved KERNEL_PANIC
check to when bled is less than 0.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: David Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Now the driver issues a soft reset and waits for the controller to be up
and running by periodically checking on the status of the controller
health registers. Also prevents ARC adapters from issuing soft reset if
IOP resets failed.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: David Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added function that waits with a timeout for the ctrl to be up and running
after triggering an IOP reset. Also removed 30 sec sleep as it is not
needed.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: David Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reworked IOP reset to remove unneeded variable and created a helper
function to notify fw of an imminent IOP reset.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: David Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver can now trigger IOP reset with a single reset mask. Removed
code that retrieves a reset_mask from the firmware.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: David Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Log the status of the controller before issuing a reset.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: David Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Log the location of the scsi cmds before triggering a reset. This
information is useful for debugging.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: David Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Change the completion wait time for the fibs in the reset and abort
callback from 2 minutes to 15 seconds.
2 minutes is too long for waiting for completion.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: David Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Check health does not need to reset the ctrl but just return the
controller health status.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: David Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The default queue depth for non NATIVE RAW disks is calculated from the
number of fibs and number of disks or a max of 256. This causes poor disk
IO performance.
The fix is to set default qd based on the type of disks
(SATA -32 and SAS -64)
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: David Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The qd for ARC Native disks is calculated by dividing the max IO 1024
by the number of disks or 256 which ever is lower. This causes poor
disk IO performance.
The fix is set the qd based on the type of disk (SAS - 64 and SATA -
32).
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: David Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver changed the DMA consistent map after consistent memory was
allocated, this invalidated the IOMMU identity mapping. The fix was to
make sure that we set the DMA consistent mask setting once depending on
the controller card.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: Dave Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The raw srb commands do not requires memory that in the ZONE_DMA memory
space. For 32bit srb commands use GFP_DMA32 to limit the memory to 32bit
memory range (4GB).
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: Dave Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZPdbLAAoJEHm+PkMAQRiGx4wH/1nCjfnl6fE8oJ24/1gEAOUh
biFdqJkYZmlLYHVtYfLm4Ueg4adJdg0wx6qM/4RaAzmQVvLfDV34bc1qBf1+P95G
kVF+osWyXrZo5cTwkwapHW/KNu4VJwAx2D1wrlxKDVG5AOrULH1pYOYGOpApEkZU
4N+q5+M0ce0GJpqtUZX+UnI33ygjdDbBxXoFKsr24B7eA0ouGbAJ7dC88WcaETL+
2/7tT01SvDMo0jBSV0WIqlgXwZ5gp3yPGnklC3F4159Yze6VFrzHMKS/UpPF8o8E
W9EbuzwxsKyXUifX2GY348L1f+47glen/1sedbuKnFhP6E9aqUQQJXvEO7ueQl4=
=m2Gx
-----END PGP SIGNATURE-----
Merge tag 'v4.12-rc5' into for-4.13/block
We've already got a few conflicts and upcoming work depends on some of the
changes that have gone into mainline as regression fixes for this series.
Pull in 4.12-rc5 to resolve these conflicts and make it easier on down stream
trees to continue working on 4.13 changes.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This is a set of user visible fixes (excepting one format string
change). Four of the qla2xxx fixes only affect the firmware dump
path, but it's still important to the enterprise. The rest are
various NULL pointer crash conditions or outright driver hangs.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=jZXV
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of user visible fixes (excepting one format string
change).
Four of the qla2xxx fixes only affect the firmware dump path, but it's
still important to the enterprise. The rest are various NULL pointer
crash conditions or outright driver hangs"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: cxgb4i: libcxgbi: in error case RST tcp conn
scsi: scsi_debug: Avoid PI being disabled when TPGS is enabled
scsi: qla2xxx: Fix extraneous ref on sp's after adapter break
scsi: lpfc: prevent potential null pointer dereference
scsi: lpfc: Avoid NULL pointer dereference in lpfc_els_abort()
scsi: lpfc: nvmet_fc: fix format string
scsi: qla2xxx: Fix crash due to NULL pointer dereference of ctx
scsi: qla2xxx: Fix mailbox pointer error in fwdump capture
scsi: qla2xxx: Set bit 15 for DIAG_ECHO_TEST MBC
scsi: qla2xxx: Modify T262 FW dump template to specify same start/end to debug customer issues
scsi: qla2xxx: Fix crash due to mismatch mumber of Q-pair creation for Multi queue
scsi: qla2xxx: Fix NULL pointer access due to redundant fc_host_port_name call
scsi: qla2xxx: Fix recursive loop during target mode configuration for ISP25XX leaving system unresponsive
scsi: bnx2fc: fix race condition in bnx2fc_get_host_stats()
scsi: qla2xxx: don't disable a not previously enabled PCI device
Use the same values for use for request completion errors as the return
value from ->queue_rq. BLK_STS_RESOURCE is special cased to cause
a requeue, and all the others are completed as-is.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Currently we use nornal Linux errno values in the block layer, and while
we accept any error a few have overloaded magic meanings. This patch
instead introduces a new blk_status_t value that holds block layer specific
status codes and explicitly explains their meaning. Helpers to convert from
and to the previous special meanings are provided for now, but I suspect
we want to get rid of them in the long run - those drivers that have a
errno input (e.g. networking) usually get errnos that don't know about
the special block layer overloads, and similarly returning them to userspace
will usually return somethings that strictly speaking isn't correct
for file system operations, but that's left as an exercise for later.
For now the set of errors is a very limited set that closely corresponds
to the previous overloaded errno values, but there is some low hanging
fruite to improve it.
blk_status_t (ab)uses the sparse __bitwise annotations to allow for sparse
typechecking, so that we can easily catch places passing the wrong values.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
We will only have sense data if the command executed and got a SCSI
result, so this is pointless.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The class_attrs pointer is going away and it's not even being used in
this driver, so just remove it entirely.
Acked-by: "Bryant G. Ly" <bryantly@linux.vnet.ibm.com>
Cc: Michael Cyr <mikecyr@linux.vnet.ibm.com>
Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: <linux-scsi@vger.kernel.org>
Cc: <target-devel@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Changes to support a new mechanism from phyp to better synchronize the
logical partition migration (LPM) of the client partition.
This includes a new VIOCTL to register that we support this new
functionality, and 2 new Transport Event types, and finally another
new VIOCTL to let phyp know once we're ready for the Suspend.
Signed-off-by: Michael Cyr <mikecyr@us.ibm.com>
Signed-off-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
the adapter consumes two tids for every ipv6 offload
connection be it active or passive, calculate tid usage
count accordingly.
Also change the signatures of relevant functions to get
the address family.
Signed-off-by: Rizwan Ansari <rizwana@chelsio.com>
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Amir Goldstein <amir73il@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
This is nine fixes, seven of which are for the qedi driver (new in
4.10) the other two are a use after free in the cxgbi drivers and a
potential NULL dereference in the rdac device handler.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=MYEc
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is nine fixes, seven of which are for the qedi driver (new as of
4.10) the other two are a use after free in the cxgbi drivers and a
potential NULL dereference in the rdac device handler"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: libcxgbi: fix skb use after free
scsi: qedi: Fix endpoint NULL panic during recovery.
scsi: qedi: set max_fin_rt default value
scsi: qedi: Set firmware tcp msl timer value.
scsi: qedi: Fix endpoint NULL panic in qedi_set_path.
scsi: qedi: Set dma_boundary to 0xfff.
scsi: qedi: Correctly set firmware max supported BDs.
scsi: qedi: Fix bad pte call trace when iscsiuio is stopped.
scsi: scsi_dh_rdac: Use ctlr directly in rdac_failover_get()
If logout response is not received and ->ep_disconnect() is called then
close tcp conn by RST instead of FIN to cleanup conn resources
immediately.
Also move ->csk_push_tx_frames() above 'done:' to avoid calling
->csk_push_tx_frames() in error cases.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
From the context where a SCSI command is submitted it is not always
possible to figure out whether or not the queue the command is
submitted to has struct scsi_request as the first member of its
private data. Hence introduce the flag QUEUE_FLAG_SCSI_PASSTHROUGH.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Omar Sandoval <osandov@fb.com>
Cc: Don Brace <don.brace@microsemi.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Pull SCSI target fixes from Nicholas Bellinger:
"Here are the target-pending fixes for v4.12-rc4:
- ibmviscsis ABORT_TASK handling fixes that missed the v4.12 merge
window. (Bryant Ly and Michael Cyr)
- Re-add a target-core check enforcing WRITE overflow reject that was
relaxed in v4.3, to avoid unsupported iscsi-target immediate data
overflow. (nab)
- Fix a target-core-user OOPs during device removal. (MNC + Bryant
Ly)
- Fix a long standing iscsi-target potential issue where kthread exit
did not wait for kthread_should_stop(). (Jiang Yi)
- Fix a iscsi-target v3.12.y regression OOPs involving initial login
PDU processing during asynchronous TCP connection close. (MNC +
nab)
This is a little larger than usual for an -rc4, primarily due to the
iscsi-target v3.12.y regression OOPs bug-fix.
However, it's an important patch as MNC + Hannes where both able to
trigger it using a reduced iscsi initiator login timeout combined with
a backend taking a long time to complete I/Os during iscsi login
driven session reinstatement"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
iscsi-target: Always wait for kthread_should_stop() before kthread exit
iscsi-target: Fix initial login PDU asynchronous socket close OOPs
tcmu: fix crash during device removal
target: Re-add check to reject control WRITEs with overflow data
ibmvscsis: Fix the incorrect req_lim_delta
ibmvscsis: Clear left-over abort_cmd pointers
It was not possible to enable both T10 PI and TPGS because they share
the same byte in the INQUIRY response. Logically OR the TPGS value
instead of using assignment.
Reported-by: Ritika Srivastava <ritika.srivastava@oracle.com>
Reviewed-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Hung task timeouts can result if a qlogic board breaks unexpectedly
while running I/O. These tasks become hung because command srb reference
counts are not going to zero, hence the affected srbs and commands do
not get freed. This fix accounts for this extra reference in the srbs in
the case of a board failure.
Fixes: a465537ad1 ("qla2xxx: Disable the adapter and skip error recovery in case of register disconnect")
Signed-off-by: Bill Kuzeja <william.kuzeja@stratus.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Null check at line 966: if (ndlp) {, implies that ndlp might be NULL.
Functions lpfc_nlp_set_state() and lpfc_issue_els_prli() dereference
pointer ndlp. Include these function calls inside the IF block that
tests pointer ndlp.
Addresses-Coverity-ID: 1401856
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We might have a NULL pring in lpfc_els_abort(), for example on error
recovery path, since queues are destroyed during error recovery
mechanism.
In this case, we should just drop the abort since the queues will be
recreated anyway. This patch just verifies for NULL pointer and stop the
abortion of the queue in case of a NULL pring.
Also, this patch converts return type of lpfc_els_abort() from int to
void, since it's not checked anywhere.
Reported-by: Harsha Thyagaraja <hathyaga@in.ibm.com>
Reported-by: Naresh Bannoth <nbannoth@in.ibm.com>
Tested-by: Raphael Silva <raphasil@linux.vnet.ibm.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The lpfc_nvmeio_data() tracing helper always takes a format string and
three additional arguments. The latest caller has a format string with
only two integer arguments, causing this harmless warning:
drivers/scsi/lpfc/lpfc_nvmet.c: In function 'lpfc_nvmet_xmt_fcp_release':
drivers/scsi/lpfc/lpfc_nvmet.c:802:25: error: too many arguments for format [-Werror=format-extra-args]
lpfc_nvmeio_data(phba, "NVMET FCP FREE: xri x%x ste %d\n", ctxp->oxid,
We could add a dummy argument here, but it seems reasonable to print
the 'abort' flag as the third argument.
Fixes: 19b58d9473 ("nvmet_fc: add req_release to lldd api")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Overlapping changes in drivers/net/phy/marvell.c, bug fix in 'net'
restricting a HW workaround alongside cleanups in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
This is quite a big update because it includes a rework of the lpfc
driver to separate the NVMe part from the FC part. The reason for
doing this is because two separate trees (the nvme and scsi trees
respectively) want to update the individual components and this
separation will prevent a really nasty cross tree entanglement by the
time we reach the next merge window. The rest of the fixes are the
usual minor sort with no significant security implications.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=NtGp
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is quite a big update because it includes a rework of the lpfc
driver to separate the NVMe part from the FC part.
The reason for doing this is because two separate trees (the nvme and
scsi trees respectively) want to update the individual components and
this separation will prevent a really nasty cross tree entanglement by
the time we reach the next merge window.
The rest of the fixes are the usual minor sort with no significant
security implications"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (25 commits)
scsi: zero per-cmd private driver data for each MQ I/O
scsi: csiostor: fix use after free in csio_hw_use_fwconfig()
scsi: ufs: Clean up some rpm/spm level SysFS nodes upon remove
scsi: lpfc: fix build issue if NVME_FC_TARGET is not defined
scsi: lpfc: Fix NULL pointer dereference during PCI error recovery
scsi: lpfc: update version to 11.2.0.14
scsi: lpfc: Add MDS Diagnostic support.
scsi: lpfc: Fix NVMEI's handling of NVMET's PRLI response attributes
scsi: lpfc: Cleanup entry_repost settings on SLI4 queues
scsi: lpfc: Fix debugfs root inode "lpfc" not getting deleted on driver unload.
scsi: lpfc: Fix NVME I+T not registering NVME as a supported FC4 type
scsi: lpfc: Added recovery logic for running out of NVMET IO context resources
scsi: lpfc: Separate NVMET RQ buffer posting from IO resources SGL/iocbq/context
scsi: lpfc: Separate NVMET data buffer pool fir ELS/CT.
scsi: lpfc: Fix NMI watchdog assertions when running nvmet IOPS tests
scsi: lpfc: Fix NVMEI driver not decrementing counter causing bad rport state.
scsi: lpfc: Fix nvmet RQ resource needs for large block writes.
scsi: lpfc: Adding additional stats counters for nvme.
scsi: lpfc: Fix system crash when port is reset.
scsi: lpfc: Fix used-RPI accounting problem.
...
Fixes following signature in the stack trace:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000374
IP: [<ffffffffa06ec8eb>] qla2x00_sp_free_dma+0xeb/0x2a0 [qla2xxx]
Cc: <stable@vger.kernel.org> # v4.10+
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Set bit (BIT_15) to send right ECHO payload information for Diagnostic
Echo Test command.
Cc: <stable@vger.kernel.org> # v4.10+
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
when driver is loaded with Multi Queue enabled, it was noticed that
there was one less queue pair created.
Following message would indicate this:
"No resources to create additional q pair."
The result of one less queue pair means that system can crash, if the
block mq layer thinks there is an extra hardware queue available, and
the driver will use a NULL ptr qpair in that instance.
Following stack trace is seen in one of the crash:
irq_create_affinity_masks+0x98/0x530
irq_create_affinity_masks+0x98/0x530
__pci_enable_msix+0x321/0x4e0
mutex_lock+0x12/0x40
pci_alloc_irq_vectors_affinity+0xb5/0x140
qla24xx_enable_msix+0x79/0x530 [qla2xxx]
qla2x00_request_irqs+0x61/0x2d0 [qla2xxx]
qla2x00_probe_one+0xc73/0x2390 [qla2xxx]
ida_simple_get+0x98/0x100
kernfs_next_descendant_post+0x40/0x50
local_pci_probe+0x45/0xa0
pci_device_probe+0xfc/0x140
driver_probe_device+0x2c5/0x470
__driver_attach+0xdd/0xe0
driver_probe_device+0x470/0x470
bus_for_each_dev+0x6c/0xc0
driver_attach+0x1e/0x20
bus_add_driver+0x45/0x270
driver_register+0x60/0xe0
__pci_register_driver+0x4c/0x50
qla2x00_module_init+0x1ce/0x21e [qla2xxx]
Cc: <stable@vger.kernel.org> # v4.10+
Signed-off-by: Sawan Chandak <sawan.chandak@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Current API between qed and protocol modules allows passing an
additional private string - but it doesn't get utilized by qed
anywhere.
Clarify the API by removing it and renaming it 'set_name'.
CC: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If multiple tasks attempt to read the stats, it may happen that the
start_req_done completion is re-initialized while still being used by
another task, causing a list corruption.
This patch fixes the bug by adding a mutex to serialize the calls to
bnx2fc_get_host_stats().
WARNING: at lib/list_debug.c:48 list_del+0x6e/0xa0() (Not tainted)
Hardware name: PowerEdge R820
list_del corruption. prev->next should be ffff882035627d90, but was ffff884069541588
Pid: 40267, comm: perl Not tainted 2.6.32-642.3.1.el6.x86_64 #1
Call Trace:
[<ffffffff8107c691>] ? warn_slowpath_common+0x91/0xe0
[<ffffffff8107c796>] ? warn_slowpath_fmt+0x46/0x60
[<ffffffff812ad16e>] ? list_del+0x6e/0xa0
[<ffffffff81547eed>] ? wait_for_common+0x14d/0x180
[<ffffffff8106c4a0>] ? default_wake_function+0x0/0x20
[<ffffffff81547fd3>] ? wait_for_completion_timeout+0x13/0x20
[<ffffffffa05410b1>] ? bnx2fc_get_host_stats+0xa1/0x280 [bnx2fc]
[<ffffffffa04cf630>] ? fc_stat_show+0x90/0xc0 [scsi_transport_fc]
[<ffffffffa04cf8b6>] ? show_fcstat_tx_frames+0x16/0x20 [scsi_transport_fc]
[<ffffffff8137c647>] ? dev_attr_show+0x27/0x50
[<ffffffff8113b9be>] ? __get_free_pages+0xe/0x50
[<ffffffff812170e1>] ? sysfs_read_file+0x111/0x200
[<ffffffff8119a305>] ? vfs_read+0xb5/0x1a0
[<ffffffff8119b0b6>] ? fget_light_pos+0x16/0x50
[<ffffffff8119a651>] ? sys_read+0x51/0xb0
[<ffffffff810ee1fe>] ? __audit_syscall_exit+0x25e/0x290
[<ffffffff8100b0d2>] ? system_call_fastpath+0x16/0x1b
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Acked-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When pci_enable_device() or pci_enable_device_mem() fail in
qla2x00_probe_one() we bail out but do a call to
pci_disable_device(). This causes the dev_WARN_ON() in
pci_disable_device() to trigger, as the device wasn't enabled
previously.
So instead of taking the 'probe_out' error path we can directly return
*iff* one of the pci_enable_device() calls fails.
Additionally rename the 'probe_out' goto label's name to the more
descriptive 'disable_device'.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Fixes: e315cd28b9 ("[SCSI] qla2xxx: Code changes for qla data structure refactoring")
Cc: <stable@vger.kernel.org>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Giridhar Malavali <giridhar.malavali@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
skb->data is assigned to task->hdr in cxgbi_conn_alloc_pdu(),
skb gets freed after tx but task->hdr is still dereferenced in
iscsi_tcp_task_xmit() to avoid this call skb_get() after allocating skb
and free the skb in cxgbi_cleanup_task() or before allocating new skb in
cxgbi_conn_alloc_pdu().
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
max_fin_rt is the maximum re-transmission of FIN packets
as part of the termination flow. After reaching this value
the FW will send a single RESET.
Signed-off-by: Nilesh Javali <nilesh.javali@cavium.com>
Signed-off-by: Manish Rangankar <manish.rangankar@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
munmap done by iscsiuio during a stop of the service triggers a "bad
pte" warning sometimes. munmap kernel path goes through the mmapped
pages and has a validation check for mapcount (in struct page) to be
zero or above. kzalloc, which we had used to allocate udev->ctrl, uses
slab allocations, which re-uses mapcount (union) for other purposes that
can make the mapcount look negative. Avoid all these trouble by invoking
one of the __get_free_pages wrappers to be used instead of kzalloc for
udev->ctrl.
BUG: Bad page map in process iscsiuio pte:80000000aa624067 pmd:3e6777067
page:ffffea0002a98900 count:2 mapcount:-2143289280
mapping: (null) index:0xffff8800aa624e00
page flags: 0x10075d00000090(dirty|slab)
page dumped because: bad pte
addr:00007fcba70a3000 vm_flags:0c0400fb anon_vma: (null)
mapping:ffff8803edf66e90 index:0
Call Trace:
dump_stack+0x19/0x1b
print_bad_pte+0x1af/0x250
unmap_page_range+0x7a7/0x8a0
unmap_single_vma+0x81/0xf0
unmap_vmas+0x49/0x90
unmap_region+0xbe/0x140
? vma_rb_erase+0x121/0x220
do_munmap+0x245/0x420
vm_munmap+0x41/0x60
SyS_munmap+0x22/0x30
tracesys+0xdd/0xe2
Signed-off-by: Arun Easi <arun.easi@cavium.com>
Signed-off-by: Manish Rangankar <manish.rangankar@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pull block fixes from Jens Axboe:
"A small collection of fixes that should go into this cycle.
- a pull request from Christoph for NVMe, which ended up being
manually applied to avoid pulling in newer bits in master. Mostly
fibre channel fixes from James, but also a few fixes from Jon and
Vijay
- a pull request from Konrad, with just a single fix for xen-blkback
from Gustavo.
- a fuseblk bdi fix from Jan, fixing a regression in this series with
the dynamic backing devices.
- a blktrace fix from Shaohua, replacing sscanf() with kstrtoull().
- a request leak fix for drbd from Lars, fixing a regression in the
last series with the kref changes. This will go to stable as well"
* 'for-linus' of git://git.kernel.dk/linux-block:
nvmet: release the sq ref on rdma read errors
nvmet-fc: remove target cpu scheduling flag
nvme-fc: stop queues on error detection
nvme-fc: require target or discovery role for fc-nvme targets
nvme-fc: correct port role bits
nvme: unmap CMB and remove sysfs file in reset path
blktrace: fix integer parse
fuseblk: Fix warning in super_setup_bdi_name()
block: xen-blkback: add null check to avoid null pointer dereference
drbd: fix request leak introduced by locking/atomic, kref: Kill kref_sub()
This is the first sweep of mostly minor fixes. There's one security
one: the read past the end of a buffer in qedf, and a panic fix for
lpfc SLI-3 adapters, but the rest are a set of include and build
dependency tidy ups and assorted other small fixes and updates.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=FJ21
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is the first sweep of mostly minor fixes. There's one security
one: the read past the end of a buffer in qedf, and a panic fix for
lpfc SLI-3 adapters, but the rest are a set of include and build
dependency tidy ups and assorted other small fixes and updates"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: pmcraid: remove redundant check to see if request_size is less than zero
scsi: lpfc: ensure els_wq is being checked before destroying it
scsi: cxlflash: Select IRQ_POLL
scsi: qedf: Avoid reading past end of buffer
scsi: qedf: Cleanup the type of io_log->op
scsi: lpfc: double lock typo in lpfc_ns_rsp()
scsi: qedf: properly update arguments position in function call
scsi: scsi_lib: Add #include <scsi/scsi_transport.h>
scsi: MAINTAINERS: update OSD entries
scsi: Skip deleted devices in __scsi_device_lookup
scsi: lpfc: Fix panic on BFS configuration
scsi: libfc: do not flood console with messages 'libfc: queue full ...'
In lower layer driver's (LLD) scsi_host_template, the driver may
optionally ask SCSI to allocate its private driver memory for each
command, by specifying cmd_size. This memory is allocated at the end of
scsi_cmnd by SCSI. Later when SCSI queues a command, the LLD can use
scsi_cmd_priv to get to its private data.
Some LLD, e.g. hv_storvsc, doesn't clear its private data before use. In
this case, the LLD may get to stale or uninitialized data in its private
driver memory. This may result in unexpected driver and hardware
behavior.
Fix this problem by also zeroing the private driver memory before
passing them to LLD.
Signed-off-by: Long Li <longli@microsoft.com>
Reviewed-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Reviewed-by: KY Srinivasan <kys@microsoft.com>
Reviewed-by: Christoph Hellwig <hch@infradead.org>
CC: <stable@vger.kernel.org> # 4.11+
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
mbp pointer is passed to csio_hw_validate_caps() so call mempool_free()
after calling csio_hw_validate_caps().
Signed-off-by: Varun Prakash <varun@chelsio.com>
Fixes: 541c571fa2 ("csiostor:Use firmware version from cxgb4/t4fw_version.h")
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When reloading module these two attributes aren't cleaned up properly
and they persist causing warnings when trying to load module
again. Additionally they are not recreated properly due to that.
Signed-off-by: Michał Potomski <michalx.potomski@intel.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This pushes qed [and as result, all qed* drivers] into using 8.20.0.0
firmware. The changes are mostly contained in qed with minor changes
to qedi due to some HSI changes.
Content-wise, the firmware contains fixes to various issues exposed
since the release of the previous firmware, including:
- Corrects iSCSI fast retransmit when data digest is enabled.
- Stop draining packets when receiving several consecutive PFCs.
- Prevent possible assertion when consecutively opening/closing
many connections.
- Prevent possible assertion due to too long BDQ fetch time.
In addition, the new firmware would allow us to later add iWARP support
in qed and qedr.
Changes from previous version
-----------------------------
- V2: Fix warning in qed_debug.c
Signed-off-by: Chad Dupuis <Chad.Dupuis@cavium.com>
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mauro says:
This patch series convert the remaining DocBooks to ReST.
The first version was originally
send as 3 patch series:
[PATCH 00/36] Convert DocBook documents to ReST
[PATCH 0/5] Convert more books to ReST
[PATCH 00/13] Get rid of DocBook
The lsm book was added as if it were a text file under
Documentation. The plan is to merge it with another file
under Documentation/security, after both this series and
a security Documentation patch series gets merged.
It also adjusts some Sphinx-pedantic errors/warnings on
some kernel-doc markups.
I also added some patches here to add PDF output for all
existing ReST books.
fix build issue if NVME_FC_TARGET is not defined. noop the code. The
code will never be invoked if target mode is not enabled.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Recent commit on patchset "lpfc updates for 11.2.0.14" fixed an issue
about dereferencing a NULL pointer on port reset. The specific commit,
named "lpfc: Fix system crash when port is reset.", is missing a check
against NULL pointer on lpfc_els_flush_cmd() though.
Since we destroy the queues on adapter resets, like in PCI error
recovery path, we need the validation present on this patch in order to
avoid a NULL pointer dereference when trying to flush commands of ELS
wq, after it has been destroyed (which would lead to a kernel oops).
Tested-by: Raphael Silva <raphasil@linux.vnet.ibm.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Change driver version to 11.2.0.14.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added code to support Cisco MDS loopback diagnostic. The diagnostics run
various loopbacks including one which loops-back frame through the
driver.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Code review of NVMEI's FC_PORT_ROLE_NVME_DISCOVERY looked wrong.
Discussions with storage architecture team clarified NVMEI's audit of
the PRLI response port roles. Following up discussion with code review
showed a few minor corrections were required - especially in
anticipation of NVME auto discovery.
During PRLI, NVMEI should sent prli_init - which it it does. NVMET
should send prli_tgt and prli_disc - which it does. When NVMEI receives
a PRLI Response now, it audits the incoming target bits and stores the
attributes in the corresponding NDLP. Later, when NVMEI registers the
NVME rport, it uses the stored ndlp attributes to set the rport
port_roles correctly.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Too many work items being processed in IRQ context take a lot of CPU
time and cause problems.
With a recent change, we get out of the ISR after hitting entry_repost
work items on a queue. However, the actual values for entry repost are
still high. EQ is 128 and CQ is 128, this could translate into
processing 128 * 128 (16384) work items under IRQ context.
Set entry_repost in the actual queue creation routine now. Limit EQ
repost to 8 and CQ repost to 64 to further limit the amount of time
spent in the IRQ.
Fix fof IRQ routines as well.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When unloading and reloading the driver, the driver fails to recreate
the lpfc root inode in the debugfs tree.
The driver is incorrectly removing the lpfc root inode in
lpfc_debugfs_terminate in the first driver instance that unloads and
then sets the lpfc_debugfs_root global parameter to NULL. When the
final driver instance unloads, the debugfs calls quietly ignore the
remove on a NULL pointer. The bug is that the debugfs_remove call
returns void so the driver doesn't know to correctly set the global
parameter to NULL.
Base the debugfs_remove of the lpfc_debugfs_root parameter on
lpfc_debugfs_hba_count because this parameter tracks the fnX instance
tracked per driver instance.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When the driver send the RPA command, it does not send supported FC4
Type NVME to the management server.
Encode NVME (type x28) in the AttribEntry in the RPA command.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Previous logic would just drop the IO.
Added logic to queue the IO to wait for an IO context resource from an
IO thats already in progress.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently IO resources are mapped 1 to 1 with RQ buffers posted
Added logic to separate RQE buffers from IO op resources
(sgl/iocbq/context). During initialization, the driver will determine
how many SGLs it will allocate for NVMET (based on what the firmware
reports) and associate a NVMET IOCBq and NVMET context structure with
each one.
Now that hdr/data buffers are immediately reposted back to the RQ, 512
RQEs for each MRQ is sufficient. Also, since NVMET data buffers are now
128 bytes, lpfc_nvmet_mrq_post is not necessary anymore as we will
always post the max (512) buffers per NVMET MRQ.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Using 2048 byte buffer and onle 128 bytes is needed.
Create nee LFPC_NVMET_DATA_BUF_SIZE define to use for NVMET RQ/MRQs.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After running IOPS test for 30 second we get kernel:NMI watchdog:
Watchdog detected hard LOCKUP on cpu 0
The driver is speend too much time in its ISR.
In ISR EQ and CQ processing routines, if we hit the entry_repost numbers
of EQE/CQEs just break out of the routine as opposed to hitting the
doorbell with NOARM and continue processing.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During driver boot, a latency in the NVMET driver side causes the
incoming NVMEI PRLI to get rejected by the NVMET driver. When this
happens, the NVMEI driver runs out of PRLI retries. Bouncing the link
does not fix the situation.
If the NVMEI driver decides, on PRLI completion failures, to retry the
PRLI, always decrement the fc4_prli_sent counter. This allows the PRLI
completion to resolve to UNMAPPED when NVMET rejects the PRLI.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Large block writes to the nvme target were failing because the default
number of RQs posted was insufficient.
Expand the NVMET RQs to 2048 RQEs and ensure a minimum of 512 RQEs are
posted, no matter how many MRQs are configured.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
More debug messages added for nvme statistics.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver panic when using the els_wq during port reset.
Check for NULL els_wq before dereferencing.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
With 255 vports created a link trasition can casue a crash.
When going through discovery after a link bounce the driver is using
rpis before the cmd FCOE_POST_HDR_TEMPLATES completes. By doing that the
next rpi bumps the rpi range out of the boundary.
The fix it to increment the next_rpi only when the
FCOE_POST_HDR_TEMPLATE succeeds.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Previous assignment was causing the use of the uninitialized variable
_explan_ inside fc_seq_ls_rjt() function, which in this particular case
is being called by fc_seq_els_rsp_send().
[mkp: fixed typo]
Addresses-Coverity-ID: 1398125
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some external hard drives don't support the sync command even though the
hard drive has write cache enabled. In this case, upon suspend request,
sync cache failures are ignored if the error code in the sense header is
ILLEGAL_REQUEST. There's not much we can do for these drives, so we
shouldn't fail to suspend for this error case. The drive may stay
powered if that's the setup for the port it's plugged into.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Sphinx is very pedantic with regards to ident/spacing.
Fix some kernel-doc markups in order to solve those
errors/warnings:
./drivers/scsi/scsicam.c:121: WARNING: Inline emphasis start-string without end-string.
./drivers/scsi/scsicam.c:121: WARNING: Inline emphasis start-string without end-string.
./drivers/scsi/scsicam.c:121: WARNING: Inline emphasis start-string without end-string.
./drivers/scsi/scsi_scan.c:1056: ERROR: Unexpected indentation.
./drivers/scsi/scsi_scan.c:1057: WARNING: Block quote ends without a blank line; unexpected unindent.
./drivers/scsi/scsi_transport_fc.c:2918: ERROR: Unexpected indentation.
./drivers/scsi/scsi_transport_fc.c:2921: WARNING: Block quote ends without a blank line; unexpected unindent.
./drivers/scsi/scsi_transport_fc.c:2922: WARNING: Enumerated list ends without a blank line; unexpected unindent.
No functional changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The current code is not correctly calculating the req_lim_delta.
We want to make sure vscsi->credit is always incremented when
we do not send a response for the scsi op. Thus for the case where
there is a successfully aborted task we need to make sure the
vscsi->credit is incremented.
v2 - Moves the original location of the vscsi->credit increment
to a better spot. Since if we increment credit, the next command
we send back will have increased req_lim_delta. But we probably
shouldn't be doing that until the aborted cmd is actually released.
Otherwise the client will think that it can send a new command, and
we could find ourselves short of command elements. Not likely, but could
happen.
This patch depends on both:
commit 25e7853126 ("ibmvscsis: Do not send aborted task response")
commit 98883f1b54 ("ibmvscsis: Clear left-over abort_cmd pointers")
Signed-off-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Reviewed-by: Michael Cyr <mikecyr@linux.vnet.ibm.com>
Cc: <stable@vger.kernel.org> # v4.8+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
With the addition of ibmvscsis->abort_cmd pointer within
commit 25e7853126 ("ibmvscsis: Do not send aborted task response"),
make sure to explicitly NULL these pointers when clearing
DELAY_SEND flag.
Do this for two cases, when getting the new new ibmvscsis
descriptor in ibmvscsis_get_free_cmd() and before posting
the response completion in ibmvscsis_send_messages().
Signed-off-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Reviewed-by: Michael Cyr <mikecyr@linux.vnet.ibm.com>
Cc: <stable@vger.kernel.org> # v4.8+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull SCSI target updates from Nicholas Bellinger:
"Things were a lot more calm than previously expected. It's primarily
fixes in various areas, with most of the new functionality centering
around TCMU backend driver work that Xiubo Li has been driving.
Here's the summary on the feature side:
- Make T10-PI verify configurable for emulated (FILEIO + RD) backends
(Dmitry Monakhov)
- Allow target-core/TCMU pass-through to use in-kernel SPC-PR logic
(Bryant Ly + MNC)
- Add TCMU support for growing ring buffer size (Xiubo Li + MNC)
- Add TCMU support for global block data pool (Xiubo Li + MNC)
and on the bug-fix side:
- Fix COMPARE_AND_WRITE non GOOD status handling for READ phase
failures (Gary Guo + nab)
- Fix iscsi-target hang with explicitly changing per NodeACL
CmdSN number depth with concurrent login driven session
reinstatement. (Gary Guo + nab)
- Fix ibmvscsis fabric driver ABORT task handling (Bryant Ly)
- Fix target-core/FILEIO zero length handling (Bart Van Assche)
Also, there was an OOPs introduced with the WRITE_VERIFY changes that
I ended up reverting at the last minute, because as not unusual Bart
and I could not agree on the fix in time for -rc1. Since it's specific
to a conformance test, it's been reverted for now.
There is a separate patch in the queue to address the underlying
control CDB write overflow regression in >= v4.3 separate from the
WRITE_VERIFY revert here, that will be pushed post -rc1"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (30 commits)
Revert "target: Fix VERIFY and WRITE VERIFY command parsing"
IB/srpt: Avoid that aborting a command triggers a kernel warning
IB/srpt: Fix abort handling
target/fileio: Fix zero-length READ and WRITE handling
ibmvscsis: Do not send aborted task response
tcmu: fix module removal due to stuck thread
target: Don't force session reset if queue_depth does not change
iscsi-target: Set session_fall_back_to_erl0 when forcing reinstatement
target: Fix compare_and_write_callback handling for non GOOD status
tcmu: Recalculate the tcmu_cmd size to save cmd area memories
tcmu: Add global data block pool support
tcmu: Add dynamic growing data area feature support
target: fixup error message in target_tg_pt_gp_tg_pt_gp_id_store()
target: fixup error message in target_tg_pt_gp_alua_access_type_store()
target/user: PGR Support
target: Add WRITE_VERIFY_16
Documentation/target: add an example script to configure an iSCSI target
target: Use kmalloc_array() in transport_kmap_data_sg()
target: Use kmalloc_array() in compare_and_write_callback()
target: Improve size determinations in two functions
...
If the list search in sg_get_rq_mark() fails to find a valid request, we
return a bogus element. This then can later lead to a GPF in
sg_remove_scat().
So don't return bogus Sg_requests in sg_get_rq_mark() but NULL in case
the list search doesn't find a valid request.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Doug Gilbert <dgilbert@interlog.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Doug Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For a zoned block device, sd_zbc_complete() handles zone write unlock on
completion of a REQ_OP_WRITE_ZEROES command but the zone write locking
is missing from sd_setup_write_zeroes_cmnd(). This patch fixes this
problem by locking the target zone of a REQ_OP_WRITE_ZEROES request.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi_io_init() may fail, leaving a zone of a zoned block device locked.
Fix this by properly unlocking the write same request target zone if
scsi_io_init() fails.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
-----BEGIN PGP SIGNATURE-----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=lbS7
-----END PGP SIGNATURE-----
Merge tag 'hwparam-20170420' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull hw lockdown support from David Howells:
"Annotation of module parameters that configure hardware resources
including ioports, iomem addresses, irq lines and dma channels.
This allows a future patch to prohibit the use of such module
parameters to prevent that hardware from being abused to gain access
to the running kernel image as part of locking the kernel down under
UEFI secure boot conditions.
Annotations are made by changing:
module_param(n, t, p)
module_param_named(n, v, t, p)
module_param_array(n, t, m, p)
to:
module_param_hw(n, t, hwtype, p)
module_param_hw_named(n, v, t, hwtype, p)
module_param_hw_array(n, t, hwtype, m, p)
where the module parameter refers to a hardware setting
hwtype specifies the type of the resource being configured. This can
be one of:
ioport Module parameter configures an I/O port
iomem Module parameter configures an I/O mem address
ioport_or_iomem Module parameter could be either (runtime set)
irq Module parameter configures an I/O port
dma Module parameter configures a DMA channel
dma_addr Module parameter configures a DMA buffer address
other Module parameter configures some other value
Note that the hwtype is compile checked, but not currently stored (the
lockdown code probably won't require it). It is, however, there for
future use.
A bonus is that the hwtype can also be used for grepping.
The intention is for the kernel to ignore or reject attempts to set
annotated module parameters if lockdown is enabled. This applies to
options passed on the boot command line, passed to insmod/modprobe or
direct twiddling in /sys/module/ parameter files.
The module initialisation then needs to handle the parameter not being
set, by (1) giving an error, (2) probing for a value or (3) using a
reasonable default.
What I can't do is just reject a module out of hand because it may
take a hardware setting in the module parameters. Some important
modules, some ipmi stuff for instance, both probe for hardware and
allow hardware to be manually specified; if the driver is aborts with
any error, you don't get any ipmi hardware.
Further, trying to do this entirely in the module initialisation code
doesn't protect against sysfs twiddling.
[!] Note that in and of itself, this series of patches should have no
effect on the the size of the kernel or code execution - that is
left to a patch in the next series to effect. It does mark
annotated kernel parameters with a KERNEL_PARAM_FL_HWPARAM flag in
an already existing field"
* tag 'hwparam-20170420' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs: (38 commits)
Annotate hardware config module parameters in sound/pci/
Annotate hardware config module parameters in sound/oss/
Annotate hardware config module parameters in sound/isa/
Annotate hardware config module parameters in sound/drivers/
Annotate hardware config module parameters in fs/pstore/
Annotate hardware config module parameters in drivers/watchdog/
Annotate hardware config module parameters in drivers/video/
Annotate hardware config module parameters in drivers/tty/
Annotate hardware config module parameters in drivers/staging/vme/
Annotate hardware config module parameters in drivers/staging/speakup/
Annotate hardware config module parameters in drivers/staging/media/
Annotate hardware config module parameters in drivers/scsi/
Annotate hardware config module parameters in drivers/pcmcia/
Annotate hardware config module parameters in drivers/pci/hotplug/
Annotate hardware config module parameters in drivers/parport/
Annotate hardware config module parameters in drivers/net/wireless/
Annotate hardware config module parameters in drivers/net/wan/
Annotate hardware config module parameters in drivers/net/irda/
Annotate hardware config module parameters in drivers/net/hamradio/
Annotate hardware config module parameters in drivers/net/ethernet/
...
A bunch of changes to virtio, most affecting virtio net.
ptr_ring batched zeroing - first of batching enhancements
that seems ready.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZEceWAAoJECgfDbjSjVRpg8YIAIbB1UJZkrHh/fdCQjM2O53T
ESS62W91LBT+weYH/N79RrfnGWzDOHrCQ8Or1nAKQZx2vU1aroqYXeJ9o0liRBYr
hGZB1/bg8obA5XkKUfME2+XClakvuXABUJbky08iDL9nILlrvIVLoUgZ9ouL0vTj
oUv4n6jtguNFV7tk/injGNRparEVdcefX0dbPxXomx5tSeD2fOE96/Q4q2eD3f7r
NHD4DailEJC7ndJGa6b4M9g8shkXzgEnSw+OJHpcJcxCnAzkVT94vsU7OluiDvmG
bfdGZNb0ohDYZLbJDR8aiMkoad8bIVLyGlhqnMBiZQEOF4oiWM9UJLvp5Lq9g7A=
=Sb7L
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio updates from Michael Tsirkin:
"Fixes, cleanups, performance
A bunch of changes to virtio, most affecting virtio net. Also ptr_ring
batched zeroing - first of batching enhancements that seems ready."
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
s390/virtio: change maintainership
tools/virtio: fix spelling mistake: "wakeus" -> "wakeups"
virtio_net: tidy a couple debug statements
ptr_ring: support testing different batching sizes
ringtest: support test specific parameters
ptr_ring: batch ring zeroing
virtio: virtio_driver doc
virtio_net: don't reset twice on XDP on/off
virtio_net: fix support for small rings
virtio_net: reduce alignment for buffers
virtio_net: rework mergeable buffer handling
virtio_net: allow specifying context for rx
virtio: allow extra context per descriptor
tools/virtio: fix build breakage
virtio: add context flag to find vqs
virtio: wrap find_vqs
ringtest: fix an assert statement
The 2nd check to see if request_size is less than zero is redundant
because the first check takes error exit path on this condition. So,
since it is redundant, remove it.
Detected by CoverityScan, CID#146149 ("Logically Dead Code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
I believe there is a typo on the wq destroy of els_wq, currently the
driver is checking if els_cq is not null and I think this should be a
check on els_wq instead.
Detected by CoverityScan, CID#1411629 ("Copy-paste error")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver now uses IRQ_POLL and needs to select it to avoid the
following build error.
ERROR: ".irq_poll_complete" [drivers/scsi/cxlflash/cxlflash.ko] undefined!
ERROR: ".irq_poll_sched" [drivers/scsi/cxlflash/cxlflash.ko] undefined!
ERROR: ".irq_poll_disable" [drivers/scsi/cxlflash/cxlflash.ko] undefined!
ERROR: ".irq_poll_init" [drivers/scsi/cxlflash/cxlflash.ko] undefined!
Fixes: cba06e6de4 ("scsi: cxlflash: Implement IRQ polling for RRQ processing")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Using memcpy() from a string that is shorter than the length copied
means the destination buffer is being filled with arbitrary data from
the kernel rodata segment. Instead, use strncpy() which will fill the
trailing bytes with zeros.
This was found with the future CONFIG_FORTIFY_SOURCE feature.
Cc: Daniel Micay <danielmicay@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We store sc_cmd->cmnd[0] which is an unsigned char in io_log->op so
this should also be unsigned char. The other thing is that this is
displayed in the debugfs:
seq_printf(s, "0x%02x:", io_log->op);
Smatch complains that the formatting won't work for negative values so
changing it to unsigned silences that warning as well.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is a double lock bug here so this will deadlock instead of
unlocking.
Fixes: 1c5b12f763 ("Fix implicit logo and RSCN handling for NVMET")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Properly update the position of the arguments in function call.
Addresses-Coverity-ID: 1402010
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch avoids that when building with W=1 the compiler complains
that __scsi_init_queue() has not been declared. See also commit
d48777a633 ("scsi: remove __scsi_alloc_queue").
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When a device is unplugged from a SCSI controller, if the scsi_device is
still in use by application layer, it won't get released until users
close it.
In this case, scsi_device_remove just set the scsi_device's state to be
SDEV_DEL. But if you plug the disk just before the old scsi_device is
released, then there will be two scsi_device structures in
scsi_host->__devices. When the next unplug event happens, some low-level
drivers will check whether the scsi_device has been added to host (for
example the MegaRAID SAS series controller) by calling
scsi_device_lookup(call __scsi_device_lookup) in function
megasas_aen_polling. __scsi_device_lookup will return the first
scsi_device. Because its state is SDEV_DEL, the scsi_device_lookup will
return NULL, making the low-level driver assume that the scsi_device has
been removed, and won't call scsi_device_remove which will lead to hot
swap failure.
Signed-off-by: Zhou Zhengping <johnzzpcrystal@gmail.com>
Tested-by: Zeng Rujia <ZengRujia@sangfor.com.cn>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=195607
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
To select the appropriate shost template, the driver is issuing a
mailbox command to retrieve the wwn. Turns out the sending of the
command precedes the reset of the function. On SLI-4 adapters, this is
inconsequential as the mailbox command location is specified by dma via
the BMBX register. However, on SLI-3 adapters, the location of the
mailbox command submission area changes. When the function is first
powered on or reset, the cmd is submitted via PCI bar memory. Later the
driver changes the function config to use host memory and DMA. The
request to start a mailbox command is the same, a simple doorbell write,
regardless of submission area. So.. if there has not been a boot driver
run against the adapter, the mailbox command works as defaults are
ok. But, if the boot driver has configured the card and, and if no
platform pci function/slot reset occurs as the os starts, the mailbox
command will fail. The SLI-3 device will use the stale boot driver dma
location. This can cause PCI eeh errors.
Fix is to reset the sli-3 function before sending the mailbox command,
thus synchronizing the function/driver on mailbox location.
Note: The fix uses routines that are typically invoked later in the call
flow to reset the sli-3 device. The issue in using those routines is
that the normal (non-fix) flow does additional initialization, namely
the allocation of the pport structure. So, rather than significantly
reworking the initialization flow so that the pport is alloc'd first,
pointer checks are added to work around it. Checks are limited to the
routines invoked by a sli-3 adapter (s3 routines) as this fix/early call
is only invoked on a sli3 adapter. Nothing changes post the
fix. Subsequent initialization, and another adapter reset, still occur -
both on sli-3 and sli-4 adapters.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Fixes: 96418b5e2c ("scsi: lpfc: Fix eh_deadline setting for sli3 adapters.")
Cc: stable@vger.kernel.org # v4.11+
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When the FCoE sending side becomes congested libfc tries to reduce the
queue depth on the host; however due to the built-in lag before
attempting to ramp down the queue depth _again_ the message log is
flooded with the following message:
libfc: queue full, reducing can_queue to 512
With this patch the message is printed only once (ie when it's
actually changed).
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We now have memalloc_noreclaim_{save,restore} helpers for robust setting
and clearing of PF_MEMALLOC. Let's convert the code which was using the
generic tsk_restore_flags(). No functional change.
[vbabka@suse.cz: in net/core/sock.c the hunk is missing]
Link: http://lkml.kernel.org/r/20170405074700.29871-4-vbabka@suse.cz
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Josef Bacik <jbacik@fb.com>
Cc: Lee Duncan <lduncan@suse.com>
Cc: Chris Leech <cleech@redhat.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Wouter Verhelst <w@uter.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove an inline from a fairly big function that is used often. It's
unlikely that calling or not calling it makes a lot of difference.
Saves around 8k text in my kernel.
text data bss dec hex filename
9047801 5367568 11116544 25531913 1859609 vmlinux-before-megasas
9039417 5367568 11116544 25523529 1857549 vmlinux-megasas
Link: http://lkml.kernel.org/r/20170315021431.13107-7-andi@firstfloor.org
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: Kashyap Desai <kashyap.desai@avagotech.com>
Cc: Sumit Saxena <sumit.saxena@avagotech.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This typo is quite common. Fix it and add it to the spelling file so
that checkpatch catches it earlier.
Link: http://lkml.kernel.org/r/20170317011131.6881-2-sboyd@codeaurora.org
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull block fixes and updates from Jens Axboe:
"Some fixes and followup features/changes that should go in, in this
merge window. This contains:
- Two fixes for lightnvm from Javier, fixing problems in the new code
merge previously in this merge window.
- A fix from Jan for the backing device changes, fixing an issue in
NFS that causes a failure to mount on certain setups.
- A change from Christoph, cleaning up the blk-mq init and exit
request paths.
- Remove elevator_change(), which is now unused. From Bart.
- A fix for queue operation invocation on a dead queue, from Bart.
- A series fixing up mtip32xx for blk-mq scheduling, removing a
bandaid we previously had in place for this. From me.
- A regression fix for this series, fixing a case where we wait on
workqueue flushing from an invalid (non-blocking) context. From me.
- A fix/optimization from Ming, ensuring that we don't both quiesce
and freeze a queue at the same time.
- A fix from Peter on lock ordering for CPU hotplug. Not a real
problem right now, but will be once the CPU hotplug rework goes in.
- A series from Omar, cleaning up out blk-mq debugfs support, and
adding support for exporting info from schedulers in debugfs as
well. This is really useful in debugging stalls or livelocks. From
Omar"
* 'for-linus' of git://git.kernel.dk/linux-block: (28 commits)
mq-deadline: add debugfs attributes
kyber: add debugfs attributes
blk-mq-debugfs: allow schedulers to register debugfs attributes
blk-mq: untangle debugfs and sysfs
blk-mq: move debugfs declarations to a separate header file
blk-mq: Do not invoke queue operations on a dead queue
blk-mq-debugfs: get rid of a bunch of boilerplate
blk-mq-debugfs: rename hw queue directories from <n> to hctx<n>
blk-mq-debugfs: don't open code strstrip()
blk-mq-debugfs: error on long write to queue "state" file
blk-mq-debugfs: clean up flag definitions
blk-mq-debugfs: separate flags with |
nfs: Fix bdi handling for cloned superblocks
block/mq: Cure cpu hotplug lock inversion
lightnvm: fix bad back free on error path
lightnvm: create cmd before allocating request
blk-mq: don't use sync workqueue flushing from drivers
mtip32xx: convert internal commands to regular block infrastructure
mtip32xx: cleanup internal tag assumptions
block: don't call blk_mq_quiesce_queue() after queue is frozen
...
The driver is sending a response to the actual scsi op that was
aborted by an abort task TM, while LIO is sending a response to
the abort task TM.
ibmvscsis_tgt does not send the response to the client until
release_cmd time. The reason for this was because if we did it
at queue_status time, then the client would be free to reuse the
tag for that command, but we're still using the tag until the
command is released at release_cmd time, so we chose to delay
sending the response until then. That then caused this issue, because
release_cmd is always called, even if queue_status is not.
SCSI spec says that the initiator that sends the abort task
TM NEVER gets a response to the aborted op and with the current
code it will send a response. Thus this fix will remove that response
if the CMD_T_ABORTED && !CMD_T_TAS.
Another case with a small timing window is the case where if LIO sends a
TMR_DOES_NOT_EXIST, and the release_cmd callback is called for the TMR Abort
cmd before the release_cmd for the (attemped) aborted cmd, then we need to
ensure that we send the response for the (attempted) abort cmd to the client
before we send the response for the TMR Abort cmd.
Cc: <stable@vger.kernel.org> # v4.8+
Signed-off-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Signed-off-by: Michael Cyr <mikecyr@linux.vnet.ibm.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Here is the big set of new char/misc driver drivers and features for
4.12-rc1.
There's lots of new drivers added this time around, new firmware drivers
from Google, more auxdisplay drivers, extcon drivers, fpga drivers, and
a bunch of other driver updates. Nothing major, except if you happen to
have the hardware for these drivers, and then you will be happy :)
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWQvAgg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yknsACgzkAeyz16Z97J3UTaeejbR7nKUCAAoKY4WEHY
8O9f9pr9gj8GMBwxeZQa
=OIfB
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big set of new char/misc driver drivers and features for
4.12-rc1.
There's lots of new drivers added this time around, new firmware
drivers from Google, more auxdisplay drivers, extcon drivers, fpga
drivers, and a bunch of other driver updates. Nothing major, except if
you happen to have the hardware for these drivers, and then you will
be happy :)
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (136 commits)
firmware: google memconsole: Fix return value check in platform_memconsole_init()
firmware: Google VPD: Fix return value check in vpd_platform_init()
goldfish_pipe: fix build warning about using too much stack.
goldfish_pipe: An implementation of more parallel pipe
fpga fr br: update supported version numbers
fpga: region: release FPGA region reference in error path
fpga altera-hps2fpga: disable/unprepare clock on error in alt_fpga_bridge_probe()
mei: drop the TODO from samples
firmware: Google VPD sysfs driver
firmware: Google VPD: import lib_vpd source files
misc: lkdtm: Add volatile to intentional NULL pointer reference
eeprom: idt_89hpesx: Add OF device ID table
misc: ds1682: Add OF device ID table
misc: tsl2550: Add OF device ID table
w1: Remove unneeded use of assert() and remove w1_log.h
w1: Use kernel common min() implementation
uio_mf624: Align memory regions to page size and set correct offsets
uio_mf624: Refactor memory info initialization
uio: Allow handling of non page-aligned memory regions
hangcheck-timer: Fix typo in comment
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJZChTBAAoJELDendYovxMvkXEIAJDpK5UKMsL1Ihgc0DL0OujQ
UGxLfWJueSA1X7i8BgL/8vfgKxSEB9SUiM+ooHOKXS6oDhyk2RP4MuCe5+lhUbbv
ZMK5KxHMlVUOD9EjYif8DhhiwRowBbWYEwr8XgY12s0Ya0a9TQLVC+noGsuzqNiH
1UyzeeWlBae4nulUMMim6urPNq5AEPVeQKNX3S8rlnDp74IKVZuoISMM62b2KRSr
+R8FVBshXR/HO53YNY0+AfmmUa8T1+dyjL50Eo/QnsG0i+3igOqNrzSKSc6T+nBt
Zl3KDUE5W3/OlxuR+CIdZZ1KKtjzoAiR3cvVlHs2z7MIio87bJcYJforAqe6Evo=
=k6in
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.12b-rc0b-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen updates from Juergen Gross:
"Xen fixes and featrues for 4.12. The main changes are:
- enable building the kernel with Xen support but without enabling
paravirtualized mode (Vitaly Kuznetsov)
- add a new 9pfs xen frontend driver (Stefano Stabellini)
- simplify Xen's cpuid handling by making use of cpu capabilities
(Juergen Gross)
- add/modify some headers for new Xen paravirtualized devices
(Oleksandr Andrushchenko)
- EFI reset_system support under Xen (Julien Grall)
- and the usual cleanups and corrections"
* tag 'for-linus-4.12b-rc0b-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: (57 commits)
xen: Move xen_have_vector_callback definition to enlighten.c
xen: Implement EFI reset_system callback
arm/xen: Consolidate calls to shutdown hypercall in a single helper
xen: Export xen_reboot
xen/x86: Call xen_smp_intr_init_pv() on BSP
xen: Revert commits da72ff5bfc and 72a9b18629
xen/pvh: Do not fill kernel's e820 map in init_pvh_bootparams()
xen/scsifront: use offset_in_page() macro
xen/arm,arm64: rename __generic_dma_ops to xen_get_dma_ops
xen/arm,arm64: fix xen_dma_ops after 815dd18 "Consolidate get_dma_ops..."
xen/9pfs: select CONFIG_XEN_XENBUS_FRONTEND
x86/cpu: remove hypervisor specific set_cpu_features
vmware: set cpu capabilities during platform initialization
x86/xen: use capabilities instead of fake cpuid values for xsave
x86/xen: use capabilities instead of fake cpuid values for x2apic
x86/xen: use capabilities instead of fake cpuid values for mwait
x86/xen: use capabilities instead of fake cpuid values for acpi
x86/xen: use capabilities instead of fake cpuid values for acc
x86/xen: use capabilities instead of fake cpuid values for mtrr
x86/xen: use capabilities instead of fake cpuid values for aperf
...
Pull networking updates from David Millar:
"Here are some highlights from the 2065 networking commits that
happened this development cycle:
1) XDP support for IXGBE (John Fastabend) and thunderx (Sunil Kowuri)
2) Add a generic XDP driver, so that anyone can test XDP even if they
lack a networking device whose driver has explicit XDP support
(me).
3) Sparc64 now has an eBPF JIT too (me)
4) Add a BPF program testing framework via BPF_PROG_TEST_RUN (Alexei
Starovoitov)
5) Make netfitler network namespace teardown less expensive (Florian
Westphal)
6) Add symmetric hashing support to nft_hash (Laura Garcia Liebana)
7) Implement NAPI and GRO in netvsc driver (Stephen Hemminger)
8) Support TC flower offload statistics in mlxsw (Arkadi Sharshevsky)
9) Multiqueue support in stmmac driver (Joao Pinto)
10) Remove TCP timewait recycling, it never really could possibly work
well in the real world and timestamp randomization really zaps any
hint of usability this feature had (Soheil Hassas Yeganeh)
11) Support level3 vs level4 ECMP route hashing in ipv4 (Nikolay
Aleksandrov)
12) Add socket busy poll support to epoll (Sridhar Samudrala)
13) Netlink extended ACK support (Johannes Berg, Pablo Neira Ayuso,
and several others)
14) IPSEC hw offload infrastructure (Steffen Klassert)"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2065 commits)
tipc: refactor function tipc_sk_recv_stream()
tipc: refactor function tipc_sk_recvmsg()
net: thunderx: Optimize page recycling for XDP
net: thunderx: Support for XDP header adjustment
net: thunderx: Add support for XDP_TX
net: thunderx: Add support for XDP_DROP
net: thunderx: Add basic XDP support
net: thunderx: Cleanup receive buffer allocation
net: thunderx: Optimize CQE_TX handling
net: thunderx: Optimize RBDR descriptor handling
net: thunderx: Support for page recycling
ipx: call ipxitf_put() in ioctl error path
net: sched: add helpers to handle extended actions
qed*: Fix issues in the ptp filter config implementation.
qede: Fix concurrency issue in PTP Tx path processing.
stmmac: Add support for SIMATIC IOT2000 platform
net: hns: fix ethtool_get_strings overflow in hns driver
tcp: fix wraparound issue in tcp_lp
bpf, arm64: fix jit branch offset related to ldimm64
bpf, arm64: implement jiting of BPF_XADD
...
We are going to add more parameters to find_vqs, let's wrap the call so
we don't need to tweak all drivers every time.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Remove the request_idx parameter, which can't be used safely now that we
support I/O schedulers with blk-mq. Except for a superflous check in
mtip32xx it was unused anyway.
Also pass the tag_set instead of just the driver data - this allows drivers
to avoid some code duplication in a follow on cleanup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Pull uaccess unification updates from Al Viro:
"This is the uaccess unification pile. It's _not_ the end of uaccess
work, but the next batch of that will go into the next cycle. This one
mostly takes copy_from_user() and friends out of arch/* and gets the
zero-padding behaviour in sync for all architectures.
Dealing with the nocache/writethrough mess is for the next cycle;
fortunately, that's x86-only. Same for cleanups in iov_iter.c (I am
sold on access_ok() in there, BTW; just not in this pile), same for
reducing __copy_... callsites, strn*... stuff, etc. - there will be a
pile about as large as this one in the next merge window.
This one sat in -next for weeks. -3KLoC"
* 'work.uaccess' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (96 commits)
HAVE_ARCH_HARDENED_USERCOPY is unconditional now
CONFIG_ARCH_HAS_RAW_COPY_USER is unconditional now
m32r: switch to RAW_COPY_USER
hexagon: switch to RAW_COPY_USER
microblaze: switch to RAW_COPY_USER
get rid of padding, switch to RAW_COPY_USER
ia64: get rid of copy_in_user()
ia64: sanitize __access_ok()
ia64: get rid of 'segment' argument of __do_{get,put}_user()
ia64: get rid of 'segment' argument of __{get,put}_user_check()
ia64: add extable.h
powerpc: get rid of zeroing, switch to RAW_COPY_USER
esas2r: don't open-code memdup_user()
alpha: fix stack smashing in old_adjtimex(2)
don't open-code kernel_setsockopt()
mips: switch to RAW_COPY_USER
mips: get rid of tail-zeroing in primitives
mips: make copy_from_user() zero tail explicitly
mips: clean and reorder the forest of macros...
mips: consolidate __invoke_... wrappers
...
Pull second round of block layer updates from Jens Axboe:
- Further fixups to the NVMe APST code, from Andy.
- Various fixes for (mostly) nvme-fc, from Christoph and James.
- NVMe scsi fixes from Jon and Christoph.
* 'for-4.12/post-merge' of git://git.kernel.dk/linux-block: (39 commits)
nvme-scsi: remove nvme_trans_security_protocol
nvme-lightnvm: add missing endianess conversion in nvme_nvm_end_io
nvme-scsi: Consider LBA format in IO splitting calculation
nvme-fc: avoid memory corruption caused by calling nvmf_free_options() twice
lpfc: Fix memory corruption of the lpfc_ncmd->list pointers
nvme: Add nvme_core.force_apst to ignore the NO_APST quirk
nvme: Display raw APST configuration via DYNAMIC_DEBUG
nvme: Fix APST comment
lpfc revison 11.2.0.12
Fix Express lane queue creation.
Update ABORT processing for NVMET.
Fix implicit logo and RSCN handling for NVMET
Add Fabric assigned WWN support.
Fix max_sgl_segments settings for NVME / NVMET
Fix crash after issuing lip reset
Fix driver load issues when MRQ=8
Remove hba lock from NVMET issue WQE.
Fix nvme initiator handling when not enabled.
Fix driver usage of 128B WQEs when WQ_CREATE is V1.
Fix driver unload/reload operation.
...
Pull block layer updates from Jens Axboe:
- Add BFQ IO scheduler under the new blk-mq scheduling framework. BFQ
was initially a fork of CFQ, but subsequently changed to implement
fairness based on B-WF2Q+, a modified variant of WF2Q. BFQ is meant
to be used on desktop type single drives, providing good fairness.
From Paolo.
- Add Kyber IO scheduler. This is a full multiqueue aware scheduler,
using a scalable token based algorithm that throttles IO based on
live completion IO stats, similary to blk-wbt. From Omar.
- A series from Jan, moving users to separately allocated backing
devices. This continues the work of separating backing device life
times, solving various problems with hot removal.
- A series of updates for lightnvm, mostly from Javier. Includes a
'pblk' target that exposes an open channel SSD as a physical block
device.
- A series of fixes and improvements for nbd from Josef.
- A series from Omar, removing queue sharing between devices on mostly
legacy drivers. This helps us clean up other bits, if we know that a
queue only has a single device backing. This has been overdue for
more than a decade.
- Fixes for the blk-stats, and improvements to unify the stats and user
windows. This both improves blk-wbt, and enables other users to
register a need to receive IO stats for a device. From Omar.
- blk-throttle improvements from Shaohua. This provides a scalable
framework for implementing scalable priotization - particularly for
blk-mq, but applicable to any type of block device. The interface is
marked experimental for now.
- Bucketized IO stats for IO polling from Stephen Bates. This improves
efficiency of polled workloads in the presence of mixed block size
IO.
- A few fixes for opal, from Scott.
- A few pulls for NVMe, including a lot of fixes for NVMe-over-fabrics.
From a variety of folks, mostly Sagi and James Smart.
- A series from Bart, improving our exposed info and capabilities from
the blk-mq debugfs support.
- A series from Christoph, cleaning up how handle WRITE_ZEROES.
- A series from Christoph, cleaning up the block layer handling of how
we track errors in a request. On top of being a nice cleanup, it also
shrinks the size of struct request a bit.
- Removal of mg_disk and hd (sorry Linus) by Christoph. The former was
never used by platforms, and the latter has outlived it's usefulness.
- Various little bug fixes and cleanups from a wide variety of folks.
* 'for-4.12/block' of git://git.kernel.dk/linux-block: (329 commits)
block: hide badblocks attribute by default
blk-mq: unify hctx delay_work and run_work
block: add kblock_mod_delayed_work_on()
blk-mq: unify hctx delayed_run_work and run_work
nbd: fix use after free on module unload
MAINTAINERS: bfq: Add Paolo as maintainer for the BFQ I/O scheduler
blk-mq-sched: alloate reserved tags out of normal pool
mtip32xx: use runtime tag to initialize command header
scsi: Implement blk_mq_ops.show_rq()
blk-mq: Add blk_mq_ops.show_rq()
blk-mq: Show operation, cmd_flags and rq_flags names
blk-mq: Make blk_flags_show() callers append a newline character
blk-mq: Move the "state" debugfs attribute one level down
blk-mq: Unregister debugfs attributes earlier
blk-mq: Only unregister hctxs for which registration succeeded
blk-mq-debugfs: Rename functions for registering and unregistering the mq directory
blk-mq: Let blk_mq_debugfs_register() look up the queue name
blk-mq: Register <dev>/queue/mq after having registered <dev>/queue
ide-pm: always pass 0 error to ide_complete_rq in ide_do_devset
ide-pm: always pass 0 error to __blk_end_request_all
..
Christoph writes:
"A couple more updates for 4.12. The biggest pile is fc and lpfc
updates from James, but there are various small fixes and cleanups as
well."
Fixes up a few merge issues, and also a warning in
lpfc_nvmet_rcv_unsol_abort() if CONFIG_NVME_TARGET_FC isn't enabled.
Signed-off-by: Jens Axboe <axboe@fb.com>
trivial fix to spelling mistake in DEBUG2 debug message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This module specific flag can be made static as it does not need to be
in global scope.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Charles Chiou <charles.chiou@tw.promise.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
free_irq() expects the same device identity that was passed to
corresponding request_irq(), otherwise the IRQ is not freed.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There were pci_alloc_consistent() failures on ARM64 platform. Use
dma_alloc_coherent() with GFP_KERNEL flag DMA memory allocations.
Signed-off-by: Mahesh Rajashekhara <mahesh.rajashekhara@microsemi.com>
[hch: tweaked indentation, removed memsets]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Dave Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It could be just cmp 0xe instead of >>1 and cmp 0x7, with readable code.
Signed-off-by: Tomohiro Kusumi <tkusumi@tuxera.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
MASK_EE_STATUS added by 66ec6d59 was unused, but it seems to have been
defined to do this.
Signed-off-by: Tomohiro Kusumi <tkusumi@tuxera.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Show the SCSI CDB for pending SCSI commands in
/sys/kernel/debug/block/*/mq/*/dispatch and */rq_list. An example
of how SCSI commands are displayed by this code:
ffff8801703245c0 {.op=READ, .cmd_flags=META PRIO, .rq_flags=DONTPREP IO_STAT STATS, .tag=14, .internal_tag=-1, .cmd=Read(10) 28 00 2a 81 1b 30 00 00 08 00}
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: <linux-scsi@vger.kernel.org>
Signed-off-by: Jens Axboe <axboe@fb.com>
The SAS transport queues are only used by bsg, and bsg always looks at
the scsi_request results and never add the error passed in the end_io
callback.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
lpfc was changing the private pointer that is set/maintained by
the nvme_fc transport. This caused two issues: a) the transport, on
teardown may erroneous attempt to free whatever address was set;
and b) lfpc uses any value set in lpfc_nvme_fcp_abort() and
assumes its a valid io request.
Correct issue by properly defining a context structure for lpfc.
Lpfc also updated to clear the private context structure on io
completion.
Since this bug caused scrutiny of the way lpfc moves local request
structures between lists, also cleaned up list_del()'s to
list_del_inits()'s.
This is a nvme-specific bug. The patch was cut against the
linux-block tree, for-4.12/block tree. It should be pulled in through
that tree.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Commit da244654c6 ("[SCSI] mac_esp: fix for quadras with two esp
chips") added mac_scsi_esp_intr() to handle the IRQ lines from a pair of
on-board ESP chips (a normal shared IRQ did not work).
Proper mutual exclusion was missing from that patch. This patch fixes
race conditions between comparison and assignment of esp_chips[]
pointers.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
These module parameter variables don't need global scope, make them
static
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Resetting a zone write pointer is equivalent to discarding sectors:
after a reset, the zone sectors will contain zeros (or the format
pattern). So there is no need for mutual exclusion between a zone reset
and write. Similarly to discard, make it the responsability of the user
to properly synchronize between reset and write (as is done now for
discard and write).
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A value is assigned to the variable 'capacity' in sd_zbc_read_zones()
but that value is never used. Hence remove the variable 'capacity'.
[Damien: There is no need to initialize to 0 the variable 'ret'
in sd_zbc_read_zones()]
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Rename sd_zbc_setup_write_cmnd() to sd_zbc_write_lock_zone() to be clear
about what the function actually does. To be consistent, also rename
sd_zbc_cancel_write_cmnd() to sd_zbc_write_unlock_zone().
No functional change is introduced by this patch.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use get_unaligned_be32 and get_unaligned_be64 to obtain values from the
sense buffer instead of open coding the operations. Also change the
function return value to a bool and fix the function signature
declaration to remove spaces triggering checkpatch warnings.
No functional change is introduced by this patch.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use a switch for the sense key, and remove two pointless variables that
are only used once.
[mkp: Added UNMAP comment and removed good_bytes based on comment from
Damien]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Re-shuffle the code to be more efficient by not initializing variables
upfront (i.e. do it only when necessary). Also replace the do_div calls
with calls to sectors_to_logical().
No functional change is introduced by this patch.
[mkp: bytes_to_logical()]
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix argument names and description of function documentation comments.
No functional change is introduced by this patch.
[mkp: verbify]
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Due to relaxed ordering requirements on multiple architectures, drivers
are required to use wmb/rmb/mb combinations when they need to guarantee
observability between the memory and the HW.
The mpt3sas driver is already using wmb() for this purpose. However, it
issues a writel following wmb(). writel() function on arm/arm64
arhictectures have an embedded wmb() call inside.
This results in unnecessary performance loss and code duplication.
writel already guarantees ordering for both cpu and bus. we don't need
additional wmb()
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Acked-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Once the reserved page array is unused we can reset the 'res_in_use'
state; here we can do a lazy update without holding the mutex as we only
need to check against concurrent access, not concurrent release.
[mkp: checkpatch]
Fixes: 1bc0eb0446 ("scsi: sg: protect accesses to 'reserved' page array")
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
As Christoph Hellwig noted, SCSI commands that transfer data always have
a SG entry. The patch removes dead code in mvumi_make_sgl(),
mvumi_complete_cmd() and mvumi_timed_out() that handle zero
scsi_sg_count(scmd) case.
Also the patch adds pci_unmap_sg() on failure path in mvumi_make_sgl().
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
As pointed out by Al Viro for my previous series, the driver has no need
to call access_ok() and __copy_from_user()/__copy_to_user(). Changing
it to regular copy_from_user()/copy_to_user() simplifies the code without
any real downsides, making it less error-prone at best.
This patch by itself also addresses the warning about the access_ok()
macro on MIPS, but both fixes improve the code, so ideally we apply
them both.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
pmcraid_minor is only used in this one file and should be 'static' as suggested
by sparse:
drivers/scsi/pmcraid.c:80:1: warning: symbol 'pmcraid_minor' was not declared. Should it be static?
In Linux coding style, a literal '0' integer should not be used to represent
a NULL pointer:
drivers/scsi/pmcraid.c:348:29: warning: Using plain integer as NULL pointer
drivers/scsi/pmcraid.c:4824:49: warning: Using plain integer as NULL pointer
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The use of le32_to_cpu() etc in this driver looks completely arbitrary.
It may have made sense at some point, but it is not applied consistently,
so this driver presumably won't work on big-endian kernel builds.
Unfortunately it's unclear whether the type names or the calls to
le32_to_cpu() are the correct ones. I'm taking educated guesses here
and assume that most of the __le32 and __le16 annotations are correct,
adding the conversion helpers whereever we access those fields.
The exceptions are the 'fw_version' field that is always accessed as
big-endian, so I'm changing the type here, and the 'hrrq' values that
are accessed as little-endian, so I'm changing those the other way.
None of these changes should have any effect on little-endian
architectures like x86, but it addresses the sparse warnings.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
kernelci.org reports a new compile warning for old code in the pmcraid
driver:
arch/mips/include/asm/uaccess.h:138:21: warning: passing argument 1 of '__access_ok' makes pointer from integer without a cast [-Wint-conversion]
The warning got introduced by a cleanup to the access_ok() helper that
requires the argument to be a pointer, where the old version silently
accepts 'unsigned long' arguments as it still does on most other
architectures.
The new behavior in MIPS however seems absolutely sensible, and so far I
could only find one other file with the same issue, so the best solution
seems to be to clean up the pmcraid driver.
This makes the driver consistently use 'void __iomem *' pointers for
passing around the address of the user space ioctl arguments, which gets
rid of the kernelci warning as well as several sparse warnings.
Fixes: f0a955f4ee ("mips: sanitize __access_ok()")
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
sparse found a bug that has always been present since the driver was
merged:
drivers/scsi/pmcraid.c:2353:12: warning: context imbalance in 'pmcraid_reset_reload' - different lock contexts for basic block
Fix this by using a common unlock goto label, and also reduce the
indentation level in the function.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Our final fix before the 4.12 release (hopefully). It's an error leg
again: the fix to not bug on empty DMA transfers is returning the
wrong code and confusing the block layer.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=tuno
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fix from James Bottomley:
"Our final fix before the 4.12 release (hopefully).
It's an error leg again: the fix to not bug on empty DMA transfers is
returning the wrong code and confusing the block layer"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: return correct blkprep status code in case scsi_init_io() fails.
Update lpfc version to reflect this set of changes.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
The older sli4 adapters only supported the 64 byte WQE entry size.
The new adapter (fw) support both 64 and 128 byte WQE entry sizies.
The Express lane WQ was not being created with the 128 byte WQE sizes
when it was supported.
Not having the right WQE size created for the express lane work queue
caused the the firmware to overwrite the lun indentifier in the FCP header.
This patch correctly creates the express lane work queue with the
supported size.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
The driver with nvme had this routine stubbed.
Right now XRI_ABORTED_CQE is not handled and the FC NVMET
Transport has a new API for the driver.
Missing code path, new NVME abort API
Update ABORT processing for NVMET
There are 3 new FC NVMET Transport API/ template routines for NVMET:
lpfc_nvmet_xmt_fcp_release
This NVMET template callback routine called to release context
associated with an IO This routine is ALWAYS called last, even
if the IO was aborted or completed in error.
lpfc_nvmet_xmt_fcp_abort
This NVMET template callback routine called to abort an exchange that
has an IO in progress
nvmet_fc_rcv_fcp_req
When the lpfc driver receives an ABTS, this NVME FC transport layer
callback routine is called. For this case there are 2 paths thru the
driver: the driver either has an outstanding exchange / context for the
XRI to be aborted or not. If not, a BA_RJT is issued otherwise a BA_ACC
NVMET Driver abort paths:
There are 2 paths for aborting an IO. The first one is we receive an IO and
decide not to process it because of lack of resources. An unsolicated ABTS
is immediately sent back to the initiator as a response.
lpfc_nvmet_unsol_fcp_buffer
lpfc_nvmet_unsol_issue_abort (XMIT_SEQUENCE_WQE)
The second one is we sent the IO up to the NVMET transport layer to
process, and for some reason the NVME Transport layer decided to abort the
IO before it completes all its phases. For this case there are 2 paths
thru the driver:
the driver either has an outstanding TSEND/TRECEIVE/TRSP WQE or no
outstanding WQEs are present for the exchange / context.
lpfc_nvmet_xmt_fcp_abort
if (LPFC_NVMET_IO_INP)
lpfc_nvmet_sol_fcp_issue_abort (ABORT_WQE)
lpfc_nvmet_sol_fcp_abort_cmp
else
lpfc_nvmet_unsol_fcp_issue_abort
lpfc_nvmet_unsol_issue_abort (XMIT_SEQUENCE_WQE)
lpfc_nvmet_unsol_fcp_abort_cmp
Context flags:
LPFC_NVMET_IOP - his flag signifies an IO is in progress on the exchange.
LPFC_NVMET_XBUSY - this flag indicates the IO completed but the firmware
is still busy with the corresponding exchange. The exchange should not be
reused until after a XRI_ABORTED_CQE is received for that exchange.
LPFC_NVMET_ABORT_OP - this flag signifies an ABORT_WQE was issued on the
exchange.
LPFC_NVMET_CTX_RLS - this flag signifies a context free was requested,
but we are deferring it due to an XBUSY or ABORT in progress.
A ctxlock is added to the context structure that is used whenever these
flags are set/read within the context of an IO.
The LPFC_NVMET_CTX_RLS flag is only set in the defer_relase routine when
the transport has resolved all IO associated with the buffer. The flag is
cleared when the CTX is associated with a new IO.
An exchange can has both an LPFC_NVMET_XBUSY and a LPFC_NVMET_ABORT_OP
condition active simultaneously. Both conditions must complete before the
exchange is freed.
When the abort callback (lpfc_nvmet_xmt_fcp_abort) is envoked:
If there is an outstanding IO, the driver will issue an ABORT_WQE. This
should result in 3 completions for the exchange:
1) IO cmpl with XB bit set
2) Abort WQE cmpl
3) XRI_ABORTED_CQE cmpl
For this scenerio, after completion #1, the NVMET Transport IO rsp
callback is called. After completion #2, no action is taken with respect
to the exchange / context. After completion #3, the exchange context is
free for re-use on another IO.
If there is no outstanding activity on the exchange, the driver will send a
ABTS to the Initiator. Upon completion of this WQE, the exchange / context
is freed for re-use on another IO.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
NVMET didn't have any RSCN handling at all and
would not execute implicit LOGO when receiving a PLOGI
from an rport that NVMET had in state UNMAPPED.
Clean up the logic in lpfc_nlp_state_cleanup for
initiators (FCP and NVME). NVMET should not respond to
RSCN including allocating new ndlps so this code was
conditionalized when nvmet_support is true. The check
for NLP_RCV_PLOGI in lpfc_setup_disc_node was moved
below the check for nvmet_support to allow the NVMET
to recover initiator nodes correctly. The implicit
logo was introduced with lpfc_rcv_plogi when NVMET gets
a PLOGI on an ndlp in UNMAPPED state. The RSCN handling
was modified to not respond to an RSCN in NVMET. Instead
NVMET sends a GID_FT and determines if an NVMEP_INITIATOR
it has is UNMAPPED but no longer in the zone membership.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Quinn Tran