Creating a VLAN interface on top of ucc_geth adds 4 bytes
to the frame and the HW controller is not prepared to
TX a frame bigger than 1518 bytes which is 4 bytes too
small for a full VLAN frame. Add 16 bytes which will handle
the a simple VLAN and leaves 12 bytes for future expansion.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a busy network we see ucc_geth is dropping RX pkgs every now
and then. Increase the RX queues HW descriptors from
16 to 32 to deal with this.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here are two EHCI Tegra driver patches for your tree.
The first is a bit big, but the majority is just moving code around. It
is needed due to the other EHCI core changes that went in way back in
3.4-rc1, so this driver will now properly handle suspend/resume, as it
was broken. The other one is a minor bugfix that resolves an warning
that people have been seeing.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk+hli8ACgkQMUfUDdst+ymGdgCeKYDYx5w2N+tmSy50kjDEhSQI
534AoK3+ZQUNsEyLU8ufLtNOyPrtIH3i
=5LmY
-----END PGP SIGNATURE-----
Merge tag 'usb-3.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB patches from Greg Kroah-Hartman:
"Here are two EHCI Tegra driver patches for your tree.
The first is a bit big, but the majority is just moving code around.
It is needed due to the other EHCI core changes that went in way back
in 3.4-rc1, so this driver will now properly handle suspend/resume, as
it was broken. The other one is a minor bugfix that resolves an
warning that people have been seeing."
* tag 'usb-3.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: ehci-tegra: remove redundant gpio_set_value
EHCI: update PM methods in ehci-tegra.c
This is a deadlock bugfix that was easy to hit, and that the vt layer lock
rework got wrong, so it reverts the logic back to the way it was in 3.3 and
earlier kernels to prevent problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk+hlr4ACgkQMUfUDdst+ynGqwCfeaot2snAEoWi1qp1pU+4cAJn
8gwAoLaO//pVnVmUIplPMRtFr3tuUN/h
=z8wN
-----END PGP SIGNATURE-----
Merge tag 'tty-3.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull a TTY fix from Greg Kroah-Hartman:
"This is a deadlock bugfix that was easy to hit, and that the vt layer
lock rework got wrong, so it reverts the logic back to the way it was
in 3.3 and earlier kernels to prevent problems."
* tag 'tty-3.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
vt: Fix deadlock on scroll-lock
warning: passing argument 1 of 'pci_find_capability' discards 'const' qualifier from pointer target type
Signed-off-by: Matt Turner <mattst88@gmail.com>
The marvel_get_rtc_time and marvel_set_rtc_time are static, but they're
available through Marvel's machine vector.
Reported-by: Raúl Porcel <armin76@gentoo.org>
Signed-off-by: Matt Turner <mattst88@gmail.com>
arch/alpha/kernel/console.c:locate_and_init_vga uses vga_con, causing
build failures if VGA_CONSOLE was not set and MARVEL, TITAN, DP264, or
GENERIC alpha system types were set.
Reported-by: Raúl Porcel <armin76@gentoo.org>
Signed-off-by: Matt Turner <mattst88@gmail.com>
This reverts commit a844adfd7b.
The commit a844adfd is degrading rx sensitivity of lower rate in
HT40 mode and it is confirmed that reverting the change is
improving rx sensitivity.
spur_freq_sd (for self-corr in AGC) is defined with respect to the
center of each 20MHz channel while spur_phase_delta (for self-corr
in Rx and spur data filter) is defined with respect to the center
of current RF channel.
So in short, we need to subtract spur_freq_sd (for self-corr in AGC)
by the offset between the center of primary20 and the center of RF
channel in SW. This offset could be +/10 MHz for dynamic 40.
Cc: Madhan Jaganathan <madhanj@qca.qualcomm.com>
Signed-off-by: Kai Shi <kaishi@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
dpc_tl_lock is not acquired in the error handle code for bus down.
But it's unlocked using spin_unlock_irqrestore after finishing task
list walk down. Grab the lock before breaking the loop to avoid a
double unlock.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Highlights include:
- Fixes for the NFSv4 security negotiation
- Use the correct hostname when mounting from a private namespace
- NFS net namespace bugfixes for the pipefs filesystem
- NFSv4 GETACL bugfixes
- IPv6 bugfix for NFSv4 referrals
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=vLBv
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-3.4-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
- Fixes for the NFSv4 security negotiation
- Use the correct hostname when mounting from a private namespace
- NFS net namespace bugfixes for the pipefs filesystem
- NFSv4 GETACL bugfixes
- IPv6 bugfix for NFSv4 referrals
* tag 'nfs-for-3.4-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFSv4.1: Use the correct hostname in the client identifier string
SUNRPC: RPC client must use the current utsname hostname string
NFS: get module in idmap PipeFS notifier callback
NFS: Remove unused function nfs_lookup_with_sec()
NFS: Honor the authflavor set in the clone mount data
NFS: Fix following referral mount points with different security
NFS: Do secinfo as part of lookup
NFS: Handle exceptions coming out of nfs4_proc_fs_locations()
NFS: Fix SECINFO_NO_NAME
SUNRPC: traverse clients tree on PipeFS event
SUNRPC: set per-net PipeFS superblock before notification
SUNRPC: skip clients with program without PipeFS entries
SUNRPC: skip dead but not buried clients on PipeFS events
Avoid beyond bounds copy while caching ACL
Avoid reading past buffer when calling GETACL
fix page number calculation bug for block layout decode buffer
NFSv4.1 fix page number calculation bug for filelayout decode buffers
pnfs-obj: Remove unused variable from objlayout_get_deviceinfo()
nfs4: fix referrals on mounts that use IPv6 addrs
On SandyBridge IPS was entirely implemented in hardware and not reliant
on the driver monitoring power consumption and feeding back desired run
states, so the hardware is able to adapt quicker and more flexibly. Which
is a huge relief for us as we no longer have to carry empirically
derived magic algorithms.
Yet despite the advance in technology, the driver was still doing its
IPS polling on all machines. Restrict it to the only supported hardware,
Clarkdale/Arrandale.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Andrey Rahmatullin <wrar@wrar.name>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=49025
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We only execute intel_decrease_pllclock for pre-PCH hardware, typically
gen4 mobiles. However, in the variable declaration we did read from the
non-PCH DPLL register, quite naughty and detected by SandyBridge.
Reported-and-tested-by: Andrey Rahmatullin <wrar@wrar.name>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=49025
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
While testing, I've found that even when we are able to negotiate a
much larger rsize with the server, on-the-wire reads often end up being
capped at 128k because of ra_pages being capped at that level.
Lifting this restriction gave almost a twofold increase in sequential
read performance on my craptactular KVM test rig with a 1M rsize.
I think this is safe since the actual ra_pages that the VM requests
is run through max_sane_readahead() prior to submitting the I/O. Under
memory pressure we should end up with large readahead requests being
suppressed anyway.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Trivial patch which fixes a misplaced tab in cifs_show_options().
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=BNz+
-----END PGP SIGNATURE-----
Merge tag 'ktest-for-v3.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest
Pull two bug fixes in ktest from Steven Rostedt.
* tag 'ktest-for-v3.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest:
ktest: Fix reboot on success stopping all reboots
ktest.pl: Fix combined usage of BISECT_REVERSE and BISECT_SKIP
Pull MIPS fixes from Ralf Baechle:
"misc fixes some of which are also applicable to 3.3 and removal of an
unused function. This has been sitting in -next for ages with no
complaints. Also there are no known regressions due to these patches"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Remove get_current_pgd().
MIPS: ath79: fix AR933X WMAC reset code
MIPS: JZ4740: Fix the JZ4740_IRQ_DMA macro
MIPS: Use set_current_blocked() and block_sigmask()
The immediately preceding gpio_direction_output() already set the value,
so there's no need to repeat it. This also prevents gpio_set_value() from
WARNing when the GPIO is sleepable (e.g. is on an I2C expander); the set
direction API is always sleepable, but plain set_value isn't.
Cc: <stable@vger.kernel.org> # v3.3
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1547) rearranges the Power Management parts of the
ehci-tegra driver to match the conventions used in other EHCI platform
drivers. In particular, the controller should not be powered down by
the root hub's suspend routine; the controller's power level should be
managed by the controller's own PM methods.
The end result of the patch is that the standard ehci_bus_suspend()
and ehci_bus_resume() methods can be used instead of special-purpose
routines. The driver now uses the standard dev_pm_ops methods instead
of legacy power management. Since there is no supported wakeup
mechanism for the controller, runtime suspend is forbidden by default
(this can be overridden via sysfs, if desired).
These adjustments are needed in order to make ehci-tegra compatible
with recent changes to the USB core. The core now checks the root
hub's status following bus suspend; if the controller is automatically
powered down during bus suspend then the check will fail and the root
hub will be resumed immediately. Doing the controller power-down in a
separate method avoids this problem.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixing the locking accidentally replaced a race in the scroll
lock handling with a deadlock. Turn it back into a race for
now.
The basic problem is that there are two paths into the tty
stop/start helpers. One via the tty layer ^S/^Q handling
where we need to take the kbd_event_lock and one via the
special keyboard handler for fn_hold where we already hold
it. Probably we need to split out into a separate LED lock
but for now just go back to the race as it's a bit close
to release.
Reported-by: Clemens Ladisch <clemens@ladisch.de>
Cc: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
skb_checksum_help(skb) can return an error, we must free skb in this
case. qdisc_drop(skb, sch) can also be feeded with a NULL skb (if
skb_unshare() failed), so lets use this generic helper.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bug: The VLAN bit of the MAC RX Status Word is unreliable in several older
supported chips. Sometimes the VLAN bit is not set for valid VLAN packets
and also sometimes the VLAN bit is set for non-VLAN packets that came after
a VLAN packet. This results in a receive length error when VLAN hardware
tagging is enabled.
Fix: Variation on original fix proposed by Mirko.
The VLAN information is decoded in the status loop, and can be
applied to the received SKB there. This eliminates the need for the
separate tag field in the interface data structure. The tag has to
be copied and cleared if packet is copied. This version checked out
with vlan and normal traffic.
Note: vlan_tx_tag_present should be renamed vlan_tag_present, but that
is outside scope of this.
Reported-by: Mirko Lindner <mlindner@marvell.com>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a small packet is received, the driver copies it to a new skb to allow
reusing the full size Rx buffer. The copy was propogating the checksum offload
but not the receive hash information. The bug is impact was mostly harmless
and therefore not observed until reviewing this area of code.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CPU core ID is used to index the core_data[] array. The core ID is, however, not
sequential; 10-core CPUS can have a core ID as high as 25. Increase the limit to
32 to be able to deal with current CPUs.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: stable@vger.kernel.org # 3.0+
Acked-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Durgadoss R <durgadoss.r@intel.com>
The change to let individual tests decide to reboot the machine on
success of the entire test also prevented errors from rebooting
when an error was detected.
The "no_reboot" variable was only cleared if the test had
reboot_on_success set. But the no_reboot variable also prevents the test
rebooting when an error was detected even when REBOOT_ON_ERROR was set.
Add a new "reboot_success" variable that is used to determine if the
test should reboot on success and not touch the no_reboot variable.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
When BISECT_REVERSE and BISECT_SKIP are used together with boot or test
testing, build failures are treated as boot or test failures and
'git bisect bad' is executed instead of 'git bisect skip'. This is because
the $ret value of -1 is treated as a build failure, but the $reverse_bisect
logic does not properly handle this.
Simple fix, only invert it if it is positive.
Link: http://lkml.kernel.org/r/1335235380-8509-1-git-send-email-Russ.Dill@ti.com
Signed-off-by: Russ Dill <Russ.Dill@ti.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
* 'drm-nouveau-fixes' of git://git.freedesktop.org/git/nouveau/linux-2.6:
drm/nv10/gpio: fix thinko in mask for gpio lines 2-9
nvc0/fb: shut up PMFB interrupt after the first occurrence
drm/nouveau/hdmi: use correct hdmi regs for nvaa/nvac
drm/nouveau/bios: fix regression on some nv4x board
'ARM: OMAP3: USB: Fix the EHCI ULPI PHY reset issue' removes the include for
linux/gpio.h from omap-usb-host.c. This include indirectly includes plat/cpu.h
which is required by omap-usb-host.c. Fix the build breakage by including
it directly.
Acked-by: Keshava Munegowda <keshava_mgowda@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Russ Dill <Russ.Dill@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The driver calls cxgb_vlan_mode() from init_one(). This calls into
synchronize_rx(), which locks all the q locks, but the q locks are not
initialized until cxgb_up() -> setup_sge_qsets(). So move the call to
cxgb_vlan_mode() into cxgb_up(), after the call to setup_sge_qsets().
We also move the body of these functions up higher to avoid having to
a forward declaration.
This was found because of the lockdep warning:
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
Pid: 323, comm: work_for_cpu Not tainted 3.4.0-rc5 #28
Call Trace:
[<ffffffff8106e767>] register_lock_class+0x108/0x2d0
[<ffffffff8106ff42>] __lock_acquire+0xd3/0xd06
[<ffffffff81070fd0>] lock_acquire+0xbf/0xfe
[<ffffffff813862a6>] _raw_spin_lock_irq+0x36/0x45
[<ffffffffa01e71aa>] cxgb_vlan_mode+0x96/0xcb [cxgb3]
[<ffffffffa01f90eb>] init_one+0x8c4/0x980 [cxgb3]
[<ffffffff811fcbf0>] local_pci_probe+0x3f/0x70
[<ffffffff81042206>] do_work_for_cpu+0x10/0x22
[<ffffffff810482de>] kthread+0xa1/0xa9
[<ffffffff8138e234>] kernel_thread_helper+0x4/0x10
Contrary to what lockdep says, the code is not fine: we are locking an
uninitialized spinlock.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the support to bounce buffer added, the skb is coming as nonlinear in the
case of non-DDPed data frames for FCoE, which is mostly ok as the FCoE stack
would take care of that. However, for target mode, we have to set the FC CRC
and FC EOF field to allow the protocol stack to not drop the frame for the last
data frame of that sequence. So fix this by linearizing the skb first before
doing skb_put().
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Marcus Dennis <marcusx.e.dennis@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver was freeing memory in shutdown instead of remove. As a result
we were leaking memory if IEEE DCB was enabled and we loaded/unloaded the
driver. This change moves the freeing of the memory into the remove
routine where it belongs.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Maybe it's a typo, but it cause that igbvf can't be initialized successfully.
Set perm_addr value using valid dev_addr, although which is equal to hw.mac.addr.
Signed-off-by: Samuel Liao <samuelliao@tencent.com>
Signed-off-by: Shan Wei <davidshan@tencent.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch sets the automatic speed and duplex detection bits
in MAC_CR to enable the mac to determine its speed automatically
from the phy.
Note this must be done BEFORE the receiver or transmitter is
enabled.
Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
also explicitly set the phy to advertise 1000 speeds
Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
smsc75xx phy interrupt acknowledge needs an mdio_write to clear
PHY_INT_SRC instead of just a read like in smsc95xx.
Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix bug in phy_init loop that was ignoring BMCR reset bit, akin to smsc95xx's d946092000
Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
smsc75xx needs MII_ACCESS_BUSY to be set to correctly trigger mdio I/O. Note smsc75xx is different from smsc95xx in this regard.
Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the same issue as reported on smsc95xx, where the
usb device is connected with no ethernet cable plugged-in.
Without this patch sysfs reports the cable as present
flag@flag-desktop:~$ cat /sys/class/net/eth0/carrier
1
while it's not:
flag@flag-desktop:~$ sudo mii-tool eth0
eth0: no link
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
As s3c2412-i2s is using the s3c_i2sv2 it should call the more specialised
s3c_i2sv2_register_dai instead of simply calling snd_soc_register_dai.
Without this call the snd_soc_dai_ops structure isn't initialised correctly.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The core allocates the live copies, we shouldn't try to duplicate it and
were buggy trying to do so as we were using uninitialised data for the
control data.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Pull ARM fixes from Russell King.
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7406/1: hotplug: copy the affinity mask when forcefully migrating IRQs
ARM: 7405/1: kexec: call platform_cpu_kill on the killer rather than the victim
ARM: 7403/1: tls: remove covert channel via TPIDRURW
ARM: 7401/1: mm: Fix section mismatches
ARM: OMAP: fix DMA vs memory ordering
ARM: 7390/1: dts: versatile-pb/ab fix MMC IRQs
ARM: 7400/1: vfp: clear fpscr length and stride bits on entry to sig handler
ARM: 7399/1: vfp: move user vfp state save/restore code out of signal.c
ARM: 7398/1: l2x0: only write to debug registers on PL310
ARM: 7397/1: l2x0: only apply workaround for erratum #753970 on PL310
ARM: 7396/1: errata: only handle ARM erratum #326103 on affected cores
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPnjtXAAoJEDeqqVYsXL0MNWkIAMYc5n06Ac/gdLY8xIIYD6GA
OzLd/NQ2Q4RqZJsX26OueX2ZjMRYDixBAmiw837K9PvrLUHGfMAaninNyzDgVZ3R
pbIK45OylIQrvMAl/R7ZzqihfxJjg5utqEUt1M2qv/ikkBJ8+zWAJTQKxRYJ1OAW
9QDhIP986hljNyZfDuqXBvA4XkngYeCO0WLjBOeYCseSzeV8vOLpmsD/ANHDcqA6
Ct4uM4KJWF4jHz3sN3w5T3morNwvh42onNcy++911HcH5Nc9bkOqBWQAZ5RtINp9
8rkUz3OtCCQpZz6ffF3ZXJaopuU3ELfP80t03OScr2T75SxLqLf6mFYVAcR7RpQ=
=nXrE
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of SAS and SATA fixes; there are one or two longstanding
bug fixes, but most of this is regression fixes."
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] libfc: update mfs boundry checking
[SCSI] Revert "[SCSI] libsas: fix sas port naming"
[SCSI] libsas: fix false positive 'device attached' conditions
[SCSI] libsas, libata: fix start of life for a sas ata_port
[SCSI] libsas: fix ata_eh clobbering ex_phys via smp_ata_check_ready
[SCSI] libsas: unify domain_device sas_rphy lifetimes
[SCSI] libsas: fix sas_get_port_device regression
[SCSI] libsas: fix sas_find_bcast_phy() in the presence of 'vacant' phys
[SCSI] libsas: introduce sas_work to fix sas_drain_work vs sas_queue_work
[SCSI] libata: Pass correct DMA device to scsi host
[SCSI] scsi_lib: use correct DMA device in __scsi_alloc_queue
A common flaw in UEFI systems is a refusal to POST triggered by a malformed
boot variable. Once in this state, machines may only be restored by
reflashing their firmware with an external hardware device. While this is
obviously a firmware bug, the serious nature of the outcome suggests that
operating systems should filter their variable writes in order to prevent
a malicious user from rendering the machine unusable.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joakim Tjernlund