After having removed all code dependencies we can make fsl-espi
completely independent of fsl-lib now.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for ESPI RXSKIP mode. This mode is optimized
for flash reads:
- sends a number of bytes and then reads a number of bytes
- shifts out zeros automatically when reading
Supporting RXSKIP mode is a prerequisite for supporting dual output
read mode.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that we introduced element tx_len in struct mpc8xxx_spi let's
rename element len to rx_len as it actually is the number of bytes to
receive. In addition make it unsigned.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This change addresses two issues:
- If the TX FIFO is full the ISR polls until there's free space again.
An ISR should never wait for something.
- Currently the number of bytes to transfer is rounded up to the next
multiple of 4. For most transfers therefore few bytes remain in the
TX FIFO after end of transfer.
This would cause the next transfer to fail and as a workaround the
ESPI block is disabled / re-enabled in fsl_espi_change_mode.
This seems to clear the FIFO's (although it's not mentioned in the
spec).
With this change the TX FIFO is filled as much as possible initially
and whenever the ISR is called. Also the exact number of bytes is
transferred.
The spinlock protects against a potential race if the first interrupt
occurs whilst the TX FIFO is still being initially filled.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Change register access to the method used in other drivers too.
- use register names as in the chip spec for constants
- avoid hard to read statements like
__be32 __iomem *espi_mode = ®_base->mode
- get rid of old powerpc-specific functions like in_8
In addition annotate reg_base in struct mpc8xxx_spi as __iomem.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the driver allocates a 64kb buffer for each single message.
On systems with little and fragmented memory this can result in
memory allocation errors. Solve this by pre-allocating a buffer.
This patch was developed in OpenWRT long ago, however it never
made it upstream.
I slightly modified the original patch to re-initialize the buffer
at the beginning of each transfer.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that most cleanup is done automatically the remove functions
can be significantly simplified.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Migrates the fsl-(e)spi driver to use the generic master queuing.
Avoids the "master is unqueued, this is deprecated" warning.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In current code, master->cleanup and master->setup are not set in the same
function. This makes it hard to read and not good for code maintain.
One example is in fsl-spi.c, master->cleanup is overrided in mpc8xxx_spi_probe()
which leads to a memory leak.
This patch removes mpc8xxx_spi_cleanup() and converts fsl_espi_setup to use
devm_kzalloc so we don't need to take care of freeing memory.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This relies upon of_spi_register_master to find out which gpios to use.
Acked-by: Anton Vorontsov <anton@enomsg.org>
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Anton Vorontsov <anton@enomsg.org>
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
For being able to distinguishing between the regular type of cores and others
with different entries in of_fsl_spi_match.
Acked-by: Anton Vorontsov <anton@enomsg.org>
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Anton Vorontsov <anton@enomsg.org>
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This makes the spi-fsl-spi driver usable in CPU mode outside of an FSL_SOC and
even an powerpc environment by moving CPM mode functionality to a separate file
that is only compiled and linked in an FSL_SOC environment and adding some
ifdefs to hide types and functions or provide alternatives.
For devicetree probing a "clock-frequency" property is used for clock frequency
instead of calls to FSL_SOC-specific functions.
Acked-by: Anton Vorontsov <anton@enomsg.org>
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Sort the SPI makefile and enforce the naming convention spi_*.c for
spi drivers.
This change also rolls the contents of atmel_spi.h into the .c file
since there is only one user of that particular include file.
v2: - Use 'spi-' prefix instead of 'spi_' to match what seems to be
be the predominant pattern for subsystem prefixes.
- Clean up filenames in Kconfig and header comment blocks
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Heiner Kallweit