Use BLOCK_NIL consistently rather than sometimes 0xffff and sometimes
BLOCK_NIL.
The semantic patch that finds this issue is below
(http://www.emn.fr/x-info/coccinelle/). On the other hand, the changes
were made by hand, in part because drivers/mtd/inftlcore.c contains dead
code that causes spatch to ignore a relevant function. Specifically, the
function INFTL_findwriteunit contains a do-while loop, but always takes a
return that leaves the loop on the first iteration.
// <smpl>
@r exists@
identifier f,C;
@@
f(...) { ... return C; }
@s@
identifier r.C;
expression E;
@@
@@
identifier r.f,r.C,I;
expression s.E;
@@
f(...) {
<...
(
I
|
- E
+ C
)
...>
}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
MTD internal API presently uses 32-bit values to represent
device size. This patch updates them to 64-bits but leaves
the external API unchanged. Extending the external API
is a separate issue for several reasons. First, no one
needs it at the moment. Secondly, whether the implementation
is done with IOCTLs, sysfs or both is still debated. Thirdly
external API changes require the internal API to be accepted
first.
Note that although the MTD API will be able to support 64-bit
device sizes, existing drivers do not and are not required
to do so, although NAND base has been updated.
In general, changing from 32-bit to 64-bit values cause little
or no changes to the majority of the code with the following
exceptions:
- printk message formats
- division and modulus of 64-bit values
- NAND base support
- 32-bit local variables used by mtdpart and mtdconcat
- naughtily assuming one structure maps to another
in MEMERASE ioctl
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
When iterating over a chain in reverse (oldest block first), this
patch correctly marks the PUtable[] entry of the second to last erase
block of a chain as BLOCK_NIL, regardless of whether or not it can
format the last block successfully. Before, the second to last block
was only marked as pointing to BLOCK_NIL if INFTL_formatblock()
succeeded on the last block of the chain, which could potentially
result in an infinite loop if the block was worn out and refused to
format.
Signed-off-by: Daniel Rosenthal <danielrosenthal@acm.org>
Acked-by: Greg Ungerer <gerg@snapgear.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Once upon a time, the MTD repository was using CVS.
This patch therefore removes all usages of the no longer updated CVS
keywords from the MTD code.
This also includes code that printed them to the user.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
As was discussed between Ricard Wanderlöf, David Woodhouse, Artem
Bityutskiy and me, the current API for reading/writing OOB is confusing.
The thing that introduces confusion is the need to specify ops.len
together with ops.ooblen for reads/writes that concern only OOB not data
area. So, ops.len is overloaded: when ops.datbuf != NULL it serves to
specify the length of the data read, and when ops.datbuf == NULL, it
serves to specify the full OOB read length.
The patch inlined below is the slightly updated version of the previous
patch serving the same purpose, but with the new Artem's comments taken
into account.
Artem, BTW, thanks a lot for your valuable input!
Signed-off-by: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Currently, mtd_blkdevs enforces a block size of 512, even if the drivers
can seemingly request a different size. This patch fixes mtd_blkdevs so
block sizes other than 512 work correctly.
Signed-off-by: Richard Purdie <rpurdie@openedhand.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Return -EUCLEAN on read when a bitflip was detected and corrected, so the
clients can react and eventually copy the affected block to a spare one.
Make all in kernel users aware of the change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Hopefully the last iteration on this!
The handling of out of band data on NAND was accompanied by tons of fruitless
discussions and halfarsed patches to make it work for a particular
problem. Sufficiently annoyed by I all those "I know it better" mails and the
resonable amount of discarded "it solves my problem" patches, I finally decided
to go for the big rework. After removing the _ecc variants of mtd read/write
functions the solution to satisfy the various requirements was to refactor the
read/write _oob functions in mtd.
The major change is that read/write_oob now takes a pointer to an operation
descriptor structure "struct mtd_oob_ops".instead of having a function with at
least seven arguments.
read/write_oob which should probably renamed to a more descriptive name, can do
the following tasks:
- read/write out of band data
- read/write data content and out of band data
- read/write raw data content and out of band data (ecc disabled)
struct mtd_oob_ops has a mode field, which determines the oob handling mode.
Aside of the MTD_OOB_RAW mode, which is intended to be especially for
diagnostic purposes and some internal functions e.g. bad block table creation,
the other two modes are for mtd clients:
MTD_OOB_PLACE puts/gets the given oob data exactly to/from the place which is
described by the ooboffs and ooblen fields of the mtd_oob_ops strcuture. It's
up to the caller to make sure that the byte positions are not used by the ECC
placement algorithms.
MTD_OOB_AUTO puts/gets the given oob data automaticaly to/from the places in
the out of band area which are described by the oobfree tuples in the ecclayout
data structre which is associated to the devicee.
The decision whether data plus oob or oob only handling is done depends on the
setting of the datbuf member of the data structure. When datbuf == NULL then
the internal read/write_oob functions are selected, otherwise the read/write
data routines are invoked.
Tested on a few platforms with all variants. Please be aware of possible
regressions for your particular device / application scenario
Disclaimer: Any whining will be ignored from those who just contributed "hot
air blurb" and never sat down to tackle the underlying problem of the mess in
the NAND driver grown over time and the big chunk of work to fix up the
existing users. The problem was not the holiness of the existing MTD
interfaces. The problems was the lack of time to go for the big overhaul. It's
easy to add more mess to the existing one, but it takes alot of effort to go
for a real solution.
Improvements and bugfixes are welcome!
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Most of those macros are unused and the used ones just obfuscate
the code. Remove them and fixup all users.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
MTD clients are agnostic of FLASH which needs ECC suppport.
Remove the functions and fixup the callers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix a copy/paste bug found by cpminer inside the inftlcore.c file
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Acked-by: Greg Ungerer <gerg@snapgear.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- chips/sharp.c: make two needlessly global functions static
- move some declarations to a header file where they belong to
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is the drivers/mtd part of the big kfree cleanup patch.
Remove pointless checks for NULL prior to calling kfree() in drivers/mtd/.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Acked-by: Joern Engel <joern@wohnheim.fh-wedel.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Julia Lawall