If the firmware had set up a clock to source from PLLC, go along with
it. But if we're looking for a new parent, we don't want to switch it
to PLLC because the firmware will force PLLC (and thus the AXI bus
clock) to different frequencies during over-temp/under-voltage,
without notification to Linux.
On my system, this moves the Linux-enabled HDMI state machine and DSI1
escape clock over to plld_per from pllc_per. EMMC still ends up on
pllc_per, because the firmware had set it up to use that.
Signed-off-by: Eric Anholt <eric@anholt.net>
Fixes: 41691b8862 ("clk: bcm2835: Add support for programming the audio domain clocks")
Acked-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
While the SDRAM is being driven by its dedicated PLL most of the time,
there is a little loop running in the firmware that periodically turns
on the CM SDRAM clock (using its pre-initialized parent) and switches
SDRAM to using the CM clock to do PVT recalibration.
This avoids system hangs if we choose SDRAM's parent for some other
clock, then disable that clock.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
These divide off of PLLD_PER and are used for the ethernet and wifi
PHYs source PLLs. Neither of them is currently represented by a phy
device that would grab the clock for us.
This keeps other drivers from killing the networking PHYs when they
disable their own clocks and trigger PLLD_PER's refcount going to 0.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The VPU clock is also the clock for our AXI bus, so we really can't
disable it. This might have happened during boot if, for example,
uart1 (aux_uart clock) probed and was then disabled before the other
consumers of the VPU clock had probed.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
control. While reading that clock is done the normal way from the
registers, setting it always requires some sort of special handling
to let the system survive this addition.
As the commit message explains, there are currently 3 handling-types
known. General SRAM-based code on rk3288 and before (which is waiting
essentially for the PIE support that is currently being worked on),
SCPI-based clk setting on the rk3368 through a coprocessor, which we
might support once the support for legacy scpi-variants has matured
and now on the rk3399 (and probably later) using a dcf controller that
is controlled from the arm-trusted-firmware and gets accessed through
firmware calls from the kernel. This is the variant we currently
support, but the clock type is made to support the other variants in
the future as well.
Apart from that slightly bigger chunk, we have a mix of PLL rates,
clock-ids and flags mainly for the rk3399.
And interestingly an iomap fix for the legacy gate driver, where I
hopefully could deter the submitter from actually using that in any
new works.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJXzrz5AAoJEPOmecmc0R2B0NMH/0SGrQnrUsaq0cvjZPaq8jTD
nJDVIRw099HNM3QZCfy+FZbSsnmex93clX+Fn4UdehplrCZ8ExX1wpPkMwvFcPJF
M34YyFXx5MU9OmDsJXd1UlGRD/mH0L6hKnmfBQiPbK33ObXbr7LCC1L3go+oYABN
eHaOzO1KIcdoCQd6RlVAQHCsiDy8akUJ68P2uACHZ7VVgvGw2f3NdJhOKTD5lCuf
WH/MRo9X9bPDGHpFJIX+mZzZgYsMqUjyF/mYU/VMoH70w+YZTnfcbrYpJ0VkgBYd
aQF2B9VXhed9EQG3Gfu+jgsWoWLed9AJf83UP6eMsPTPLNQBqgzoDZwylbY1Szk=
=LjDG
-----END PGP SIGNATURE-----
Merge tag 'v4.9-rockchip-clk1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into clk-next
Pull rockchip clk driver updates from Heiko Stuebner:
The biggest addition is probably the special clock-type for ddr clock
control. While reading that clock is done the normal way from the
registers, setting it always requires some sort of special handling
to let the system survive this addition.
As the commit message explains, there are currently 3 handling-types
known. General SRAM-based code on rk3288 and before (which is waiting
essentially for the PIE support that is currently being worked on),
SCPI-based clk setting on the rk3368 through a coprocessor, which we
might support once the support for legacy scpi-variants has matured
and now on the rk3399 (and probably later) using a dcf controller that
is controlled from the arm-trusted-firmware and gets accessed through
firmware calls from the kernel. This is the variant we currently
support, but the clock type is made to support the other variants in
the future as well.
Apart from that slightly bigger chunk, we have a mix of PLL rates,
clock-ids and flags mainly for the rk3399.
And interestingly an iomap fix for the legacy gate driver, where I
hopefully could deter the submitter from actually using that in any
new works.
* tag 'v4.9-rockchip-clk1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
clk: rockchip: use the dclk_vop_frac clock ids on rk3399
clk: rockchip: drop CLK_SET_RATE_PARENT from rk3399 fractional dividers
clk: rockchip: add 2016M to big cpu clk rate table on rk3399
clk: rockchip: add rk3399 ddr clock support
clk: rockchip: add dclk_vop_frac ids for rk3399 vop
clk: rockchip: add new clock-type for the ddrclk
soc: rockchip: add header for ddr rate SIP interface
clk: rockchip: add SCLK_DDRC id for rk3399 ddrc
clk: rockchip: handle of_iomap failures in legacy clock driver
clk: rockchip: mark rk3399 hdcp_noc and vio_noc as critical
clk: rockchip: use general clock flag when registering pll
clk: rockchip: delete the CLK_IGNORE_UNUSED from aclk_pcie on rk3399
clk: rockchip: add 65MHz and 106.5MHz rates to rk3399 plls used for HDMI
Check the MD_CLK pin to determine the current clock mode in order to set
the pll clock parent correctly.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Export the dclk_vop_frac out, so we can set the dclk_vop as the
child of dclk_vop_frac, and then we can start to take use of
the fractional dividers.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Currently the fractional divider clock time can't handle the
CLK_SET_RATE_PARENT flag. This is because, unlike normal dividers,
there is no clk_divider_bestdiv() function to try speeding up the parent
to see if it helps things.
Eventually someone could try to figure out how to make fractional
dividers able to use CLK_SET_RATE_PARENT, but until they do let's not
confuse the common clock framework (and anyone using it) by setting the
flag.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
We would prefer the 2016M as 2.0G than 1992M which seems odd, adding
it to big cpu clk rate table then we can set 2016M in dts.
Signed-off-by: Shunqian Zheng <zhengsq@rock-chips.com>
Reviewed-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
add ddrc clock setting, so we can do ddr frequency
scaling on rk3399 platform in future.
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch adds support for the meson8b clock gates. Most of
them are disabled by Amlogic U-Boot, but need to be enabled
for ethernet, USB and many other components.
Signed-off-by: Alexander Müller <serveralex@gmail.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/1472319654-59048-7-git-send-email-serveralex@gmail.com
The macro used gxbb_ prefix for clock definitions. In order
to share the macro between gxbb and meson8b, the prefix must
be moved to gxbb.c.
Signed-off-by: Alexander Müller <serveralex@gmail.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/1472319654-59048-6-git-send-email-serveralex@gmail.com
Only expose future CLKID constants if necessary. This patch
removes CLK_NR_CLKS from the DT bindings but leaves all previously
defined CLKIDs there to keep backward compatibility.
Signed-off-by: Alexander Müller <serveralex@gmail.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/1472319654-59048-5-git-send-email-serveralex@gmail.com
Changing the rate of the DDR clock needs special care, as the DDR
is of course in use and will react badly if the rate changes under it.
Over time different approaches to handle that were used.
Past SoCs like the rk3288 and before would store some code in SRAM
while the rk3368 used a SCPI variant and let a coprocessor handle that.
New rockchip platforms like the rk3399 have a dcf controller to do ddr
frequency scaling, and support for this controller will be implemented
in the arm-trusted-firmware.
This new clock-type should over time handle all these methods for
handling DDR rate changes, but right now it will concentrate on the
SIP interface used to talk to ARM trusted firmware.
The SIP interface counterpart was merged from pull-request #684 [0]
into the upstream arm-trusted-firmware codebase.
[0] https://github.com/ARM-software/arm-trusted-firmware/pull/684
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Currently we see the following error when using the SAI audio
driver on mx7:
Division by zero in kernel.
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.8.0-rc3-next-20160823
Hardware name: Freescale i.MX7 Dual (Device Tree)
Backtrace:
[<c010b70c>] (dump_backtrace) from [<c010b8a8>] (show_stack+0x18)
r6:60000013 r5:ffffffff r4:00000000 r3:00000000
[<c010b890>] (show_stack) from [<c03e9324>] (dump_stack+0xb0/0xe)
[<c03e9274>] (dump_stack) from [<c010b578>] (__div0+0x18/0x20)
r8:00000000 r7:ffffffff r6:ffffffff r5:00000000 r4:00000000 r3:0
[<c010b560>] (__div0) from [<c03e795c>] (Ldiv0_64+0x8/0x18)
[<c06cd860>] (divider_get_val) from [<c06cda28>] (clk_divider_se)
This error happens due to the lack of definition of the
IMX7D_PLL_AUDIO_TEST_DIV/IMX7D_PLL_AUDIO_POST_DIV clocks.
Add support for them.
Tested on a imx7s-warp board.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch reverts commit 023bd7166b ("clk: skip unnecessary
set_phase if nothing to do"), fixing two problems:
* in some SoCs, the hardware phase delay depends on the rate ratio of
the clock and its parent. So, changing this ratio may imply to set
new hardware values, even if the logical delay is the same.
* when the delay was the same as previously, an error was returned.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Fixes: 023bd7166b ("clk: skip unnecessary set_phase if nothing to do")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add all clocks needed to use the SDHI interfaces on the Renesas R-Car M3-W
(r8a7796) SoC.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=rh+1
-----END PGP SIGNATURE-----
Merge tag 'clk-renesas-for-v4.9-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into clk-next
Pull renesas r8a7796 SDHI clock support from Geert Uytterhoeven:
Add all clocks needed to use the SDHI interfaces on the Renesas R-Car M3-W
(r8a7796) SoC.
* tag 'clk-renesas-for-v4.9-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers:
clk: renesas: r8a7796: Add SDIF clocks
clk: renesas: r8a7796: Add GPIO clocks
* clk-fixes:
clk: rockchip: mark aclk_emmc_noc as a critical clock on rk3399
clk: rockchip: fix incorrect GATE bits for {c, g}pll_aclk_perihp_src on rk3399
clk: rockchip: fix incorrect aclk_emmc source gate bits on rk3399
clk: rockchip: fix rk3399 aclk_vio gate bit
during actual use.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJXwweZAAoJEPOmecmc0R2BZKwH/0JJZiEenrjALE+6nJ2+nO33
OMRjHWOLwSjwK9wApGgwz6K8OtM/T7BDL+fOaR1GSut+jQwkSAzZt7QqFYK0GHvD
pmWze/y/5vu2C5YL+Bn1jhWCCY/FXoNV7d/IrQm/z0xiufqOr83z2snvS5IWWXLr
rOGPy/mJluuH64QyFteMJW8fxgiRrloQOUD6jcmA9qQtuM79jSusACZxi4new2Vt
HR3ExH7X6jMkqHMv0XtbbZ8t8dQ/KiId5A/eAOwqJq4cM5tSuEi7YLM+c4hSOXvo
+lMRME1HaF5eidPPnRX2layjOQNCP8GKq2+QG0HOxvpszQTcsuNDInHfq0IAV2w=
=ZxRA
-----END PGP SIGNATURE-----
Merge tag 'v4.8-rockchip-clk-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into clk-fixes
Some fixes for rk3399 register errors that revealed themself
during actual use.
* tag 'v4.8-rockchip-clk-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
clk: rockchip: mark aclk_emmc_noc as a critical clock on rk3399
clk: rockchip: fix incorrect GATE bits for {c, g}pll_aclk_perihp_src on rk3399
clk: rockchip: fix incorrect aclk_emmc source gate bits on rk3399
clk: rockchip: fix rk3399 aclk_vio gate bit
This adds support for the two ICST525-based clocks on the
Integrator/AP baseboard, as documented in the board manual
"Integrator/AP ASIC Development Motherboard", ARM DUI0098 B,
pages 3-15 thru 3-18.
Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[sboyd@codeaurora.org: fixed uninitialized val warning]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The reset register offsets for UART*, I2C* and SCR were off by a few bytes.
Signed-off-by: Jorik Jonker <jorik@kippendief.biz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
__of_clk_get_hw_from_provider() is confusing because it will
return EPROBE_DEFER if there isn't a ->get() or ->get_hw()
function pointer in a provider. That's just a bug though, and we
used to NULL pointer exception when ->get() was missing anyway,
so let's make this more obvious that they're not optional. The
assumption is that most providers will implement ->get_hw() so we
only fallback to the ->get() function if necessary. This
clarifies the intent and removes any possibility of probe defer
happening if clk providers are buggy.
Reported-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add a new style driver for the clock control unit in Allwinner A31/A31s.
A few clocks are still missing:
- MIPI PLL's HDMI mode support
- EMAC clock
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On sunxi we support cpufreq by changing the clock rate of PLL-CPU.
It's possible the clock output of the PLL goes out of the CPU's
operational limits when the PLL's multipliers / dividers are changed
and it hasn't stabilized yet. This would result in the CPU hanging.
To circumvent this, we temporarily switch the CPU mux clock to another
stable clock before the rate change, and switch it back after the PLL
stabilizes. This is done with clk notifiers registered on the PLL.
This patch adds common functions for notifiers to reparent mux clocks.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Some clocks on the A31 have fixed pre-dividers on multiple parents.
Add support for them.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Some clock muxes have holes, i.e. invalid or unconnected inputs,
between parent mux values.
Add support for specifying a mux table to map clock parents to
mux values.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Rename the internal mux macro to be consistent with the other internal
structure macros.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Integrator/AP and Integrator/CP have special derivatives
of the ICST525 control registers, where some bits have been
hardwired but others are possible to adjust, resulting in a
control register that makes it possible to set an even,
desired megahertz value.
The Integrator/AP and Integrator/CP have slightly different
layout so we support them using different compatible
strings.
After adding these clocks, the Integrator-specific cpufreq
driver can be switched over to use the generic operating
point device tree cpufreq driver.
Instead of simply writing a value to the oscillator control
register we switch to the more elaborate method of providing
a bitmask and use regmap_update_bits() to poke the right bits
for the desired frequency, this is needed since these control
registers sometimes control more than one clock.
Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch corrects the register offset for pcie2 pipe clock.
Offset according to datasheet is 0x6e018 instead of 0x6e108.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Fixes: b1e010c073 ("clk: qcom: Add MSM8996 Global Clock Control (GCC) driver")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch selects QCOM_GDSC Kconfig for msm8996 GCC and MMCC clock
controllers, as these provide some of the gdscs on the SOC.
Also selecting this config will make it align with other drivers which
do the same.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Fixes: 52111672f7 ("clk: qcom: gdsc: Add GDSCs in msm8996 GCC")
Fixes: 7e824d5079 ("clk: qcom: gdsc: Add mmcc gdscs for msm8996 family")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Now that we have clk_hw based provider APIs to register clks, we
can get rid of struct clk pointers while registering clks in
these drivers, allowing us to move closer to a clear split of
consumer and provider clk APIs.
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: <uclinux-h8-devel@lists.sourceforge.jp>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Now that we have clk_hw based provider APIs to register clks, we
can get rid of struct clk pointers in this driver, allowing us to
move closer to a clear split of consumer and provider clk APIs.
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Now that we have clk_hw based provider APIs to register clks, we
can get rid of struct clk pointers while registering clks in
these drivers, allowing us to move closer to a clear split of
consumer and provider clk APIs.
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Now that we have clk_hw based provider APIs to register clks, we
can get rid of struct clk pointers while registering clks in
these drivers, allowing us to move closer to a clear split of
consumer and provider clk APIs.
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Now that we have clk_hw based provider APIs to register clks, we
can get rid of struct clk pointers while registering clks in
these drivers, allowing us to move closer to a clear split of
consumer and provider clk APIs.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Now that we have clk_hw based provider APIs to register clks, we
can get rid of struct clk pointers while registering clks in
these drivers, allowing us to move closer to a clear split of
consumer and provider clk APIs.
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Now that we have clk_hw based provider APIs to register clks, we
can get rid of struct clk pointers while registering clks in
these drivers, allowing us to move closer to a clear split of
consumer and provider clk APIs.
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Sören Brinkmann <soren.brinkmann@xilinx.com>
Cc: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Now that we have clk_hw based provider APIs to register clks, we
can get rid of struct clk pointers while registering clks in
these drivers, allowing us to move closer to a clear split of
consumer and provider clk APIs.
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Sören Brinkmann <soren.brinkmann@xilinx.com>
Cc: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Now that we have clk_hw based provider APIs to register clks, we
can get rid of struct clk pointers while registering clks in
these drivers, allowing us to move closer to a clear split of
consumer and provider clk APIs.
Cc: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Now that we have clk_hw based provider APIs to register clks, we
can get rid of struct clk pointers while registering clks in
these drivers, allowing us to move closer to a clear split of
consumer and provider clk APIs.
Cc: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Now that we have clk_hw based provider APIs to register clks, we
can get rid of struct clk pointers while registering clks in
these drivers, allowing us to move closer to a clear split of
consumer and provider clk APIs.
Cc: Janusz Uzycki <j.uzycki@elproma.com.pl>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Now that we have clk_hw based provider APIs to register clks, we
can get rid of struct clk pointers while registering clks in
these drivers, allowing us to move closer to a clear split of
consumer and provider clk APIs.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Now that we have clk_hw based provider APIs to register clks, we
can get rid of struct clk pointers while registering clks in
these drivers, allowing us to move closer to a clear split of
consumer and provider clk APIs.
Cc: Daniel Tang <dt.tangr@gmail.com>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Now that we have clk_hw based provider APIs to register clks, we
can get rid of struct clk pointers while registering clks in
these drivers, allowing us to move closer to a clear split of
consumer and provider clk APIs.
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Now that we have clk_hw based provider APIs to register clks, we
can get rid of struct clk pointers while registering clks in
these drivers, allowing us to move closer to a clear split of
consumer and provider clk APIs.
Cc: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Now that we have clk_hw based provider APIs to register clks, we
can get rid of struct clk pointers while registering clks in
these drivers, allowing us to move closer to a clear split of
consumer and provider clk APIs.
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Now that we have clk_hw based provider APIs to register clks, we
can get rid of struct clk pointers while registering clks in
these drivers, allowing us to move closer to a clear split of
consumer and provider clk APIs.
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Now that we have clk_hw based provider APIs to register clks, we
can get rid of struct clk pointers while registering clks in
these drivers, allowing us to move closer to a clear split of
consumer and provider clk APIs.
Cc: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Now that we have clk_hw based provider APIs to register clks, we
can get rid of struct clk pointers while registering clks in
these drivers, allowing us to move closer to a clear split of
consumer and provider clk APIs.
Cc: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Now that we have clk_hw based provider APIs to register clks, we
can get rid of struct clk pointers while registering clks in
these drivers, allowing us to move closer to a clear split of
consumer and provider clk APIs.
Cc: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Now that we have clk_hw based provider APIs to register clks, we
can get rid of struct clk pointers while registering clks in
these drivers, allowing us to move closer to a clear split of
consumer and provider clk APIs. Make thing simple by using the
existing clk_hw array and implementing a custom DT clk provider
get function to map the clk spec id to a clk_hw pointer.
Cc: Anders Berg <anders.berg@lsi.com>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Now that we have clk_hw based provider APIs to register clks, we
can get rid of struct clk pointers while registering clks in
these drivers, allowing us to move closer to a clear split of
consumer and provider clk APIs.
Cc: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Now that we have clk_hw based provider APIs to register clks, we
can get rid of struct clk pointers while registering clks in
these drivers, allowing us to move closer to a clear split of
consumer and provider clk APIs.
Cc: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Now that we can use clk_hw pointers we don't need to have two
duplicate arrays holding the same mapping of clk index to clk_hw
pointer. Implement a custom clk_hw provider function to map the
OF specifier to the clk_hw instance for it.
Cc: Alex Elder <elder@linaro.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Optional SOSC is an external fixed clock running at 32768HZ.
So Initialize SOSC rate as per PIC32MZDA datasheet.
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
pbclk_set_rate() is using readl_poll_timeout_atomic() even
though spinlock is released. Fix it by replacing with
readl_poll_timeout().
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
We don't have code to handle any of the noc clocks in rk3399 and they're
all just listed as critical clocks. Let's do the same for
aclk_emmc_noc.
Without this clock being marked as critical we have problems around
suspend/resume after commit 20c389e656 ("clk: rockchip: fix incorrect
aclk_emmc source gate bits on rk3399"). Before that change we were
presumably not actually gating any of these clocks because we were
setting the wrong gate.
Fixes: 20c389e656 ("clk: rockchip: fix incorrect aclk_emmc source gate bits on rk3399")
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tegra114 has a HW bug that the PLLD/PLLD2 lock bit cannot be asserted when
the DIS power domain is during up-powergating process but the clamp to this
domain is not removed yet. That causes a timeout and aborts the power
sequence, although the PLLD/PLLD2 has already locked. To remove the false
alarm, we don't use the lock for PLLD/PLLD2. Just wait 1ms and treat the
clocks as locked.
Signed-off-by: Vince Hsu <vinceh@nvidia.com>
Tested-by: Jonathan Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
sizeof() when applied to a pointer typed expression gives the
size of the pointer, not that of the pointed data.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Fixes: f8c11f7991 ("clk: meson: Add GXBB AO Clock and Reset controller driver")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch adds SDIF clocks for R8A7796 SoC.
Based on work by Ai Kyuse and Yoshihiro Shimoda for the r8a7795 SoC.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add BIMC gdsc data found in MMCC part of msm8996 family of devices.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The SAI_IPG clocks are enabled by the same bits that control SAI_ROOT_CLK
clocks, so represent them as shared clocks.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Introduce imx_clk_gate2_shared2() which is similar to the existing
imx_clk_gate2_shared() and passes CLK_OPS_PARENT_ENABLE flag, which
is useful for i.MX7 shared clocks.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add IMX7D_SDMA_CORE_CLK clock so that SDMA can be functional.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Adds a Clock and Reset controller driver for the Always-On part
of the Amlogic Meson GXBB SoC.
It exports paired Clocks and Resets lines that will be used by
peripherals in the Always-On subsystem.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add a Kconfig to define clock configuration for each SoC, and
modify the Makefile to build drivers that only selected in config.
Signed-off-by: Shunli Wang <shunli.wang@mediatek.com>
Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
Signed-off-by: Erin Lo <erin.lo@mediatek.com>
Tested-by: John Crispin <blogic@openwrt.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Remove __init from functions that will be used by init functions
that support probe deferral.
Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
Signed-off-by: Erin Lo <erin.lo@mediatek.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Now that we have clk_hw based provider APIs to register clks, we
can get rid of struct clk pointers while registering clks in
these drivers, allowing us to move closer to a clear split of
consumer and provider clk APIs.
Cc: Kelvin Cheung <keguang.zhang@gmail.com>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The offset of Core Cluster clock control/status register
on cluster group V3 version is different from others, and
should be plus 0x70000.
Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Reviewed-by: Scott Wood <oss@buserror.net>
Fixes: 9e19ca2f62 ("clk: qoriq: Add ls2080a support.")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Now that we have clk_hw based provider APIs to register clks, we
can get rid of struct clk pointers while registering clks in
these drivers, allowing us to move closer to a clear split of
consumer and provider clk APIs.
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add all clocks related to the Watchdog Timer (WDT) controller on the
Renesas R-Car M3-W (r8a7796) SoC.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0CHq
-----END PGP SIGNATURE-----
Merge tag 'clk-renesas-for-v4.9-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into clk-next
Merge r8a7796 watchdog clk support from Geert Uytterhoeven:
Add all clocks related to the Watchdog Timer (WDT) controller on the
Renesas R-Car M3-W (r8a7796) SoC.
* tag 'clk-renesas-for-v4.9-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers:
clk: renesas: r8a7796: Add watchdog module clock
clk: renesas: r8a7796: Add watchdog core clocks
Now that we have clk_hw based provider APIs to register clks, we
can get rid of struct clk pointers while registering clks in
these drivers, allowing us to move closer to a clear split of
consumer and provider clk APIs. We also remove some __init
markings in header files as they're useless and we're in the
area.
Tested-by: Jisheng Zhang <jszhang@marvell.com>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The field "owner" is set by the core.
Thus delete an unneeded initialisation.
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
* clk-qcom-9615:
dt-bindings: clock: Update bindings for MDM9615 GCC and LCC
clk: mdm9615: Add support for MDM9615 Clock Controllers
dt-bindings: Add MDM9615 DT bindings include files for GCC and LCC
In order to support the Qualcomm MDM9615 SoC, add support for
the Global and LPASS Clock Controllers.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add the SD/eMMC gate clocks and expose them for use by DT.
While at it, also explose FCLK_DIV2 since this is one of the input
clocks to the mux internal to each of the SD/eMMC blocks.
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Maxim Max77620 has one 32KHz clock output and the clock HW
IP used on this PMIC is same as what it is there in the MAX77686.
Add clock driver support for MAX77620 on the MAX77686 driver.
CC: Krzysztof Kozlowski <k.kozlowski@samsung.com>
CC: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The clock IP used on the Maxim PMICs max77686 and max77802 are
same. The configuration of clock register is also same except
the number of clocks.
Part of common code utilisation, there is 3 files for these chips
clock driver, one for common and two files for driver registration.
Combine both drivers into single file and move common code into
same common file reduces the 2 files and make max77686 and max77802
clock driver in single fine. This driver does not depends on the
parent driver structure. The regmap handle is acquired through
regmap APIs for the register access.
This combination of driver helps on adding clock driver for different
Maxim PMICs which has similar clock IP like MAX77620 and MAX20024.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
CC: Krzysztof Kozlowski <k.kozlowski@samsung.com>
CC: Javier Martinez Canillas <javier@dowhile0.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This function is only called by builtin code, but we always
exported it and had marked it as __init before commit
e4eda8e065 (clk: remove exported function from __init section,
2013-01-06) removed that marking. Given that it isn't used by
modules, lets unexport it and add back __init.
Cc: Denis Efremov <yefremov.denis@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This function is marked __init, so it can't possibly need to be
exported to modules. Remove the marking.
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Before commit 0861e5b8cf (clk: Add clk_hw OF clk providers,
2016-02-05) __of_clk_get_from_provider() would return an error
pointer of the provider's choosing if there was a provider
registered and EPROBE_DEFER otherwise. After that commit, it
would return EPROBE_DEFER regardless of whether or not the
provider returned an error. This is odd and can lead to behavior
where clk consumers keep probe deferring when they should be
seeing some other error.
Let's restore the previous behavior where we only return
EPROBE_DEFER when there isn't a provider in our of_clk_providers
list. Otherwise, return the error from the last provider we find
that matches the node.
Reported-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Fixes: 0861e5b8cf ("clk: Add clk_hw OF clk providers")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Use the builtin_platform_driver() macro to make the code simpler.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
These clocks are the ones which will be used as source for the
peripherals of the Armada 3700 SoC. On this SoC there is two blocks of
clocks: the North bridge one and the South bridge one.
Most of them are gatable. Most of the time their rate are their parent
rated divided by a ratio depending of two registers. Their parent can be
choose between the TBG clocks for most of them.
However, some of them can't choose their parent or directly depend of the
xtal clocks. Other ones do not use exactly the same pattern to find the
ratio between their parent rate and their rate.
For these reason each clock is a composite clock and the operations they
use are different depending of the clock.
According to the datasheet it would be possible to select the parent
clock and the ratio, however currently the driver does not support it.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
These clocks are children of the xtal clock and each one can be selected
as a source for the peripheral clocks.
According to the datasheet it should be possible to modify their rate,
but currently it is not supported.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This clock is the parent of all the Armada 3700 clocks. It is a fixed
rate clock which depends on the gpio configuration read when resetting
the SoC.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The driver is to provide the functional clock to OMAP4/5 McPDM. The clock
is named as pdmclk in the documentations so change the function names,
structure names and variables to align with this.
At the same time rename the driver from "twl6040-clk" to "twl6040-pdmclk".
This can be done w/o regression since the clock driver is not in use at
the moment, the MFD core driver is not even registering the device for it.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
In order ot be able to use the pdmclk clock via DT it need to be registered
as of_clk_provide.
Since the twl6040 clock driver does not have it's own DT node, use the
parent's node for registering.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Since the drover only supports prepare callbacks, the use of is_enabled is
not correct, it should be handling is_prepared.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Both SATA and second USB3.0 interface are supported in Armada-39x SoC
family. Add necessary clk description, so both xhci and sata drivers
can be correctly initialized.
The binding documentation has also been updated accordingly.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This code is clear enough, but the intention will be even clearer
with this.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Adds support for fixed-rate clock providers which have not been
enabled via of_clk_init().
This is required by Device trees overlays that introduce clocks
providers.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
[sboyd@codeaurora.org: Make new private function static, don't
check clk for NULL when unregistering in driver remove]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Adds support for fixed-factor clock providers which have not been
enabled via of_clk_init().
This is required by Device trees overlays that introduce clocks
providers.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
[sboyd@codeaurora.org: Make new private function static, don't
check clk for NULL when unregistering in driver remove]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Some clock providers can be initialized via of_clk_init() and also via
platform device probe.
Avoid double initialization of them by setting the OF_POPULATED flag.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This driver initializes a clock provider via sun8i_a23_apb0_setup
and then continues the initialization on sun8i_a23_apb0_clk_probe.
Use the new macro to notify the clk subsystem about this behaviour.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This driver initializes a clock provider via sun4i_a10_mod0_setup
and then continues the initialization on sun4i_a10_mod0_clk_probe.
Use the new macro to notify the clk subsystem about this behaviour.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This driver initializes a clock provider via lpc18xx_creg_clk_init
and then continues the initialization on lpc18xx_creg_clk_probe.
Use the new macro to notify the clk subsystem about this behaviour.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
[sboyd@codeaurora.org: s/npx/nxp/ in subject]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This driver initializes a clock provider via of_artpec6_clkctrl_setup
and then continues the initialization on artpec6_clkctrl_probe.
Use the new macro to notify the clk subsystem about this behaviour.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
clk-divider uses clk_readl()/clk_writel() everywhere, except in
clk_divider_round_rate(), where plain readl() is used. Change this to
clk_readl(), as it makes a difference on powerpc.
Fixes: e6d5e7d90b ("clk-divider: Fix READ_ONLY when divider > 1")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Sorry to refer incorrect clock diagram, we double check it that the bits
configuration of the Xpll_aclk_perihp_src need to be fixed:
bit 1 - shows aclk_perihp_cpll_src_en
bit 0 - shows aclk_perihp_gpll_src_en
Through the testing that plug/unplug the USB ethernet cable on the RK3399 kevin board.
1. the hclk_host0 and hclk_host1 are endpoint clocks:
cpll --> G5[1] --> aclk_perihp_cpll_src --\ |--> hclk_host0
| --> ... ---> |
gpll --> G5[0] --> aclk_perihp_gpll_src --/ |--> hclk_host1
2. there is no clock below the cpll_aclk_perihp_src,
and the hclk_hostX are below the gpll_aclk_perihp_src:
pll_cpll 1 1 800000000 0 0
cpll 7 19 800000000 0 0
cpll_aclk_perihp_src 0 0 800000000 0 0
...
pll_gpll 1 1 594000000 0 0
gpll 10 10 594000000 0 0
gpll_aclk_perihp_src 2 2 594000000 0 0
hclk_perihp 5 5 74250000 0 0
hclk_host1_arb 2 2 74250000 0 0
hclk_host1 2 2 74250000 0 0
hclk_host0_arb 2 2 74250000 0 0
hclk_host0 2 2 74250000 0 0
3. by default, G5[0] and G5[1] are enabled:
localhost ~ # mem r 0xff760314
0x000003e0
4. close the G5[1] (aclk_perihp_cpll_src), and plug/unplug USB ethernet cable,
the DUT still works well:
localhost ~ # mem w 0xff760314 0xffff03e2
localhost ~ # mem r 0xff760314
0x000003e2
plug/unplug, the work statue is ok
5. close the G5[0] (aclk_perihp_gpll_src), , and plug/unplug USB ethernet cable,
the DUT will be crashed:
localhost ~ # mem w 0xff760314 0xffff03e1
localhost ~ # mem r 0xff760314
0x000003e1
plug/unplug, the DUT is crashed
Summary:
bit 1 - shows aclk_perihp_cpll_src_en
bit 0 - shows aclk_perihp_gpll_src_en
Fixes: 3bd14ae9da ("clk: rockchip: fix incorrect parent for rk3399's {c,g}pll_aclk_perihp_src")
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
[here the clock-documentation in the manual was actually stating the wrong
bits and thus only Xing's testing above revealed the issue]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Dues to incorrect diagram, we need to fix incorrect bits for
(c/g)pll_aclk_emmc_src:
cpll_aclk_emmc_src --> G6[13]
gpll_aclk_emmc_src --> G6[12]
Fixes: 115510053e ("clk: rockchip: add clock controller for the RK3399")
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Booting the kernel on a imx7s-warp leads to several warnings like these:
[ 0.000000] ------------[ cut here ]------------
[ 0.000000] WARNING: CPU: 0 PID: 0 at kernel/locking/lockdep.c:3536 lock_release+0x2f8/0x330
[ 0.000000] releasing a pinned lock
[ 0.000000] ------------[ cut here ]------------
[ 0.000000] WARNING: CPU: 0 PID: 0 at kernel/locking/lockdep.c:2722 trace_hardirqs_on_caller+0x1ac/0x1f4
[ 0.000000] DEBUG_LOCKS_WARN_ON(unlikely(early_boot_irqs_disabled))
[ 0.000000] ---[ end trace cb88537fdc8fa201 ]---
[ 0.000000] bad: scheduling from the idle thread!
[ 0.000000] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W 4.7.0-rc7-next-20160715 #404
[ 0.000000] ------------[ cut here ]------------
[ 0.000000] WARNING: CPU: 0 PID: 0 at kernel/time/sched_clock.c:179 sched_clock_register+0x44/0x1f8
[ 0.000000] Modules linked in:
[ 0.000591] ------------[ cut here ]------------
[ 0.000610] WARNING: CPU: 0 PID: 0 at kernel/time/sched_clock.c:179 sched_clock_register+0x44/0x1f8
[ 0.002084] ------------[ cut here ]------------
[ 0.002104] WARNING: CPU: 0 PID: 0 at init/main.c:576 start_kernel+0x258/0x3b0
[ 0.002114] Interrupts were enabled early
This fix is along the same lines as 5e33ebff7e ("clk: imx7d: do not
set parent of ethernet time/ref clocks") and the explanation from that
commit is:
"The reason for the warning is that setting the parent enables the ENET
PLL since we are using CLK_OPS_PARENT_ENABLE. Enabling the ENET PLL can
cause clk_pllv3_wait_lock to sleep. See also:
commit fc8726a2c0 ("clk: core: support clocks which requires parents
enable (part 2)")."
imx7s-warp does not even use the FEC interface, so we should not really
configure the parent of IMX7D_ENET_AXI_ROOT_SRC in the common MX7 clock
driver code.
The dts file should use the assigned-clocks/assigned-clock-parents method,
so simply remove the configuration of IMX7D_ENET_AXI_ROOT_SRC parent.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
It's always nice to see families reunited, and this is equally true when
talking about parent clocks and their children. However, if the orphan
clk had a positive prepare_count or enable_count, then we would not
migrate those counts up the parent chain correctly.
This has manifested with the recent critical clocks feature, which often
enables clocks very early, before their parents have been registered.
Fixed by replacing the call to clk_core_reparent with calls to
__clk_set_parent_{before,after}.
Cc: James Liao <jamesjj.liao@mediatek.com>
Cc: Erin Lo <erin.lo@mediatek.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
[sboyd@codeaurora.org: Recalc accuracies and rates too]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
According to the datasheet, SDn clocks are from the SDSRC clock. And
the SDSRC has a 1/2 divider. So, we should have ".sdsrc" as an internal
core clock. Otherwise, since the sdhi driver will calculate clock for
a sd card using the wrong parent clock rate, and then performance will
be not good.
Fixes: 90c073e539 ("clk: shmobile: r8a7795: Add SD divider support")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: stable@vger.kernel.org
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The aclk_vio_noc should be put into critical list, as the interconnect
is not handled right now, but is required by VOP.
And the Type-C DP need these clocks: aclk_hdcp_noc, hclk_hdcp_noc,
pclk_hdcp_noc. Mark them as critical to avoid someone close them.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The condition passed to read*_poll_timeout() is the break condition,
i.e. wait for this condition to happen and return success.
The original code assumed the opposite, resulting in a warning when
the PLL clock rate was changed but never lost it's lock as far as
the readout indicated. This was verified by checking the read out
register value.
Fixes: 1d80c14248 ("clk: sunxi-ng: Add common infrastructure")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch removes registration helpers and support files,
used for non-DT i.MX1 targets.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the module clock for the Watchdog Timer (WDT) controller on the
Renesas R-Car M3-W (r8a7796) SoC.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add all core clocks related to the Watchdog Timer (WDT) controller on
the Renesas R-Car M3-W (r8a7796) SoC: OSC, Internal RCLK, and RCLK.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The MIPI mode of the MIPI-PLL on A31 is an NKM-style PLL with 2
selectable parents.
Add mux support to the NKM clock.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Some clocks have a predivider value that is larger than what u8 can
store. One such example is the OUT clk found on A20/A31, which has
a /750 pre-divider on one of the osc24M parents.
Increase the size of the div field to u16.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
make C=2 reports:
CHECK drivers/clk/sunxi-ng/ccu_nk.c
drivers/clk/sunxi-ng/ccu_nk.c:17:6: warning: symbol 'ccu_nk_find_best' was
not declared. Should it be static?
ccu_nk_find_best is only used within ccu_nk.c. So make it static to get
rid of this warning.
Fixes: adbfb0056e ("clk: sunxi-ng: Add N-K-factor clock support")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The condition passed to read*_poll_timeout() is the break condition,
i.e. wait for this condition to happen and return success.
The original code assumed the opposite, resulting in a warning when
the PLL clock rate was changed but never lost it's lock as far as
the readout indicated. This was verified by checking the read out
register value.
Fixes: 1d80c14248 ("clk: sunxi-ng: Add common infrastructure")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In case of error, the function of_io_request_and_map() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should be
replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In case of error, the functions clk_register_composite() and
clk_register_divider() returns ERR_PTR() and never returns NULL.
The NULL test in the return value check should be replaced with
IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add the general flags the pll list already contains to the clock init,
so that needed clock flags can be used for plls.
Signed-off-by: Heiko Stübner <heiko@sntech.de>
We need to add more clocks for supporting more display resolution
for HDMI.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
There was only one use of __initdata_refok and __exit_refok
__init_refok was used 46 times against 82 for __ref.
Those definitions are obsolete since commit 312b1485fb ("Introduce new
section reference annotations tags: __ref, __refdata, __refconst")
This patch removes the following compatibility definitions and replaces
them treewide.
/* compatibility defines */
#define __init_refok __ref
#define __initdata_refok __refdata
#define __exit_refok __ref
I can also provide separate patches if necessary.
(One patch per tree and check in 1 month or 2 to remove old definitions)
[akpm@linux-foundation.org: coding-style fixes]
Link: http://lkml.kernel.org/r/1466796271-3043-1-git-send-email-fabf@skynet.be
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Device tree contents continue to be the largest branches we submit. This
time around, some of the contents worth pointing out is:
- New SoC platforms:
- Freescale i.MX 7Solo
- Broadcom BCM23550
- Cirrus Logic EP7209 and EP7211 (clps711x platforms)_
- Hisilicon HI3519
- Renesas R8A7792
Some of the other delta that is sticking out, line-count wise:
- Exynos moves of IP blocks under an SoC bus, which causes a large delta due
to indentation changes
- A new Tegra K1 board: Apalis
- A bunch of small updates to many Allwinner platforms; new hardware support,
some cleanup, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=C4NU
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"Device tree contents continue to be the largest branches we submit.
This time around, some of the contents worth pointing out is:
New SoC platforms:
- Freescale i.MX 7Solo
- Broadcom BCM23550
- Cirrus Logic EP7209 and EP7211 (clps711x platforms)_
- Hisilicon HI3519
- Renesas R8A7792
Some of the other delta that is sticking out, line-count wise:
- Exynos moves of IP blocks under an SoC bus, which causes a large
delta due to indentation changes
- a new Tegra K1 board: Apalis
- a bunch of small updates to many Allwinner platforms; new hardware
support, some cleanup, etc"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (426 commits)
ARM: dts: sun8i: Add dts file for inet86dz board
ARM: dts: sun8i: Add dts file for Polaroid MID2407PXE03 tablet
ARM: dts: sun8i: Use sun8i-reference-design-tablet for ga10h dts
ARM: dts: sun8i: Use sun8i-reference-design-tablet for polaroid mid2809pxe04
ARM: dts: sun8i: reference-design-tablet: Add drivevbus-supply
ARM: dts: Copy sun8i-q8-common.dtsi sun8i-reference-design-tablet.dtsi
ARM: dts: sun5i: Use sun5i-reference-design-tablet.dtsi for utoo p66 dts
ARM: dts: sun5i: Use sun5i-reference-design-tablet.dtsi for dit4350 dts
ARM: dts: sun5i: reference-design-tablet: Remove mention of q8
ARM: dts: sun5i: reference-design-tablet: Set lradc vref to avcc
ARM: dts: sun5i: Rename sun5i-q8-common.dtsi sun5i-reference-design-tablet.dtsi
ARM: dts: sun5i: Move q8 display bits to sun5i-a13-q8-tablet.dts
ARM: dts: sunxi: Rename sunxi-q8-common.dtsi sunxi-reference-design-tablet.dtsi
ARM: dts: at91: Don't build unnecessary dtbs
ARM: dts: at91: sama5d3x: separate motherboard gmac and emac definitions
ARM: dts: at91: at91sam9g25ek: fix isi endpoint node
ARM: dts: at91: move isi definition to at91sam9g25ek
ARM: dts: at91: fix i2c-gpio node name
ARM: dts: at91: vinco: fix regulator name
ARM: dts: at91: ariag25 : fix onewire node
...
Driver updates for ARM SoCs.
A slew of changes this release cycle. The reset driver tree, that we merge
through arm-soc for historical reasons, is also sizable this time around.
Among the changes:
- clps711x: Treewide changes to compatible strings, merged here for simplicity.
- Qualcomm: SCM firmware driver cleanups, move to platform driver
- ux500: Major cleanups, removal of old mach-specific infrastructure.
- Atmel external bus memory driver
- Move of brcmstb platform to the rest of bcm
- PMC driver updates for tegra, various fixes and improvements
- Samsung platform driver updates to support 64-bit Exynos platforms
- Reset controller cleanups moving to devm_reset_controller_register() APIs
- Reset controller driver for Amlogic Meson
- Reset controller driver for Hisilicon hi6220
- ARM SCPI power domain support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=O8+y
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Driver updates for ARM SoCs.
A slew of changes this release cycle. The reset driver tree, that we
merge through arm-soc for historical reasons, is also sizable this
time around.
Among the changes:
- clps711x: Treewide changes to compatible strings, merged here for simplicity.
- Qualcomm: SCM firmware driver cleanups, move to platform driver
- ux500: Major cleanups, removal of old mach-specific infrastructure.
- Atmel external bus memory driver
- Move of brcmstb platform to the rest of bcm
- PMC driver updates for tegra, various fixes and improvements
- Samsung platform driver updates to support 64-bit Exynos platforms
- Reset controller cleanups moving to devm_reset_controller_register() APIs
- Reset controller driver for Amlogic Meson
- Reset controller driver for Hisilicon hi6220
- ARM SCPI power domain support"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (100 commits)
ARM: ux500: consolidate base platform files
ARM: ux500: move soc_id driver to drivers/soc
ARM: ux500: call ux500_setup_id later
ARM: ux500: consolidate soc_device code in id.c
ARM: ux500: remove cpu_is_u* helpers
ARM: ux500: use CLK_OF_DECLARE()
ARM: ux500: move l2x0 init to .init_irq
mfd: db8500 stop passing around platform data
ASoC: ab8500-codec: remove platform data based probe
ARM: ux500: move ab8500_regulator_plat_data into driver
ARM: ux500: remove unused regulator data
soc: raspberrypi-power: add CONFIG_OF dependency
firmware: scpi: add CONFIG_OF dependency
video: clps711x-fb: Changing the compatibility string to match with the smallest supported chip
input: clps711x-keypad: Changing the compatibility string to match with the smallest supported chip
pwm: clps711x: Changing the compatibility string to match with the smallest supported chip
serial: clps711x: Changing the compatibility string to match with the smallest supported chip
irqchip: clps711x: Changing the compatibility string to match with the smallest supported chip
clocksource: clps711x: Changing the compatibility string to match with the smallest supported chip
clk: clps711x: Changing the compatibility string to match with the smallest supported chip
...
Since commit 1bdf02326b ("clk: at91: make use of syscon/regmap
internally"), clk_programmable_set_parent() is always selecting the
first parent (AKA slow_clk), no matter what's passed in the 'index'
parameter.
Fix that by initializing the pckr variable to the index value.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reported-by: Hans Verkuil <hans.verkuil@cisco.com>
Fixes: 1bdf02326b ("clk: at91: make use of syscon/regmap internally")
Cc: <stable@vger.kernel.org>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/1468828152-18389-1-git-send-email-boris.brezillon@free-electrons.com
This reverts commit e16fb2e635.
Updated documentation from the chip vendor reveals that this clock is
not required for correct operation of the MMC controller. As such, do
not expose it to DT.
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Merge "STi late updates for v4.8" from Patrice Chotard:
- Add STi DT critical clocks declaration
- Remove SPI hack wich has dependecy with critical clocks
These 2 STi DT patches and SPI hack MUST be applied after patches
contained into Stephen Boyd's branch clk-next/clk-st-critical.
This to ensure not to break SPI.
* tag 'sti-late-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti:
spi: st-ssc4: Remove 'no clocking' hack
ARM: sti: stih410-clocks: Identify critical clocks
ARM: sti: stih407-family: Supply defines for CLOCKGEN A0
clk: st: clkgen-pll: Detect critical clocks
clk: st: clkgen-fsyn: Detect critical clocks
clk: st: clk-flexgen: Detect critical clocks
of machine-local files and boardfile-type data for regulators
and ASoC.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=VLJl
-----END PGP SIGNATURE-----
Merge tag 'ux500-cleanup-bundle' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/drivers
Merge "Ux500 cleanups from Arnd" from Linus Walleij:
This is a set of cleanups for the Ux500 that reduce the number
of machine-local files and boardfile-type data for regulators
and ASoC.
* tag 'ux500-cleanup-bundle' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: consolidate base platform files
ARM: ux500: move soc_id driver to drivers/soc
ARM: ux500: call ux500_setup_id later
ARM: ux500: consolidate soc_device code in id.c
ARM: ux500: remove cpu_is_u* helpers
ARM: ux500: use CLK_OF_DECLARE()
ARM: ux500: move l2x0 init to .init_irq
mfd: db8500 stop passing around platform data
ASoC: ab8500-codec: remove platform data based probe
ARM: ux500: move ab8500_regulator_plat_data into driver
ARM: ux500: remove unused regulator data
Any clock dependencies can be properly handled with deferred probing
so we can remove core_initcall and switch to a proper loadable platform
driver module.
This change has been tested on Exynos4412 Odroid U3 based board.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/1467987300-31450-1-git-send-email-s.nawrocki@samsung.com
The Kconfig currently controlling compilation of this code is:
arch/arm/mach-s5pv210/Kconfig:config ARCH_S5PV210
arch/arm/mach-s5pv210/Kconfig: bool "Samsung S5PV210/S5PC110" if ARCH_MULTI_V7
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since this code is already not using module_init, case, the init
ordering remains unchanged with this commit.
We also delete the MODULE_LICENSE tags etc. since all that information
is already contained at the top of the file in the comments.
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20160704211220.5685-8-paul.gortmaker@windriver.com
Because the Exynos5433 SPI driver supports the ioclk handling and
the following patch:
http://marc.info/?l=linux-kernel&m=146787645626318&w=2
fixes a synchronus abort issue, none of the SPI clocks require
any critical handling: remove, then, the CLK_IGNORE_UNUSED flag
for the SPI related clocks.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/1468317736-18841-8-git-send-email-andi.shyti@samsung.com
The clk-oxnas driver is specific to its architecture, so do not
propose it on other architectures, unless build-testing.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20160707091844.196a7930@endymion
All device trees currently in mainline specify the time clock parent
using the assigned-clocks/assigned-clock-parents method, there is no
need to statically assign the parent in the core clock driver.
Also all current boards provide an Ethernet reference clock for the
PHY externally, hence configuring the internal PHY reference clock.
Furthermore, and the actual driver of this patch, specify ethernet
related parents at that early point in boot leads to a warning:
bad: scheduling from the idle thread!
The reason for the warning is that setting the parent enables the ENET
PLL since we are using CLK_OPS_PARENT_ENABLE. Enabling the ENET PLL can
cause clk_pllv3_wait_lock to sleep. See also:
commit fc8726a2c0 ("clk: core: support clocks which requires parents
enable (part 2)").
Note that setting the ENET AXI root clock parent also requires ENET
PLL to be enabled. However, U-Boot typically leaves the ENET PLL on,
hence when the framework sets the parent of the first clock, it does
not need to wait for the PLL to come up. But because there is currently
no user of that clock, the PLL gets disabled after setting the parent.
Therefore, subsequent reparenting calls of any clock which somehow rely
on the ENET PLL, need to reenable the ENET PLL which leads to a sleep.
Removing those subsequent reparenting calls works around this issue.
Also remove comments. The code is really verbose enough.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Tested-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20160703174813.13970-1-stefan@agner.ch
Eric Anholt