In the function rtl_usb_start we pre-allocate a certain number of urbs
for RX path but they will not be freed when calling rtl_usb_stop. This
results in leaking urbs when doing ifconfig up and down. Eventually,
the system has no available urbs.
Signed-off-by: Michael Schenk <michael.schenk@albis-elcon.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
fix an issue where we printed the sdio buffer before
actually read it.
Signed-off-by: Guy Mishol <guym@ti.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On some platforms, driver is unable read sleep cookie signature even
if firmware has written it through DMA. The problem is fixed by using
pci_dma_sync_single* APIs while reading DMA buffer shared with firmware.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sleep confirm is a special command for which "adapter->cur_cmd" pointer
is not set. When it's response is received, host writes SLEEP confirm done
to a register. Firmware will perform DMA for writing sleep cookie signature
on same buffer after this.
Let's not immediately call mwifiex_unmap_pci_memory() for this special
command. Unmapping will be done when firmware completes writing sleep
cookie signature.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Support for the RT5350 WiSoC was added to OpenWrt after having a
lengthy debate about the legality of the original submission, see
https://lists.openwrt.org/pipermail/openwrt-devel/2013-January/018224.html
MTK/Ralink Acked replied and says we can merge this patch under the GPL.
https://dev.openwrt.org/changeset/36177
Signed-off-by: Serge Vasilugin <vasilugin@yandex.ru>
Tested-by: Michel Stempin <michel.stempin@wanadoo.fr>
Acked-by: John Crispin <blogic@openwrt.org>
[daniel@makrotopia.org: added commit message, cleaned up code]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On Rt3352 the driver needs to know the frequency of an external
crystal which can be either 40 MHz (as on all other WiSoCs until now)
or 20 MHz.
Get the clock attached by ramips WiSoC platform code which probes
SYSC_REG_SYSCFG (added by John Crispin in commit 6ac8579b96) and
introduce a new flag clk_is_20mhz in struct hw_mode_spec to make the
driver aware and use either 40 MHz or 20 MHz specific rf_vals on those
WiSoC platforms.
The introduced support for boards with a 20 MHz crystal is also needed
for RT5350.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since clk_get() is not trivial add copy of clk pointer to rt2x00dev
for System On Chip devices and initialize it on probe routine.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It was left after reworking PCIe reset in commit 07fe2e38c7
("brcmfmac: Reset PCIE devices after recognition.").
Cc: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* A bunch of cleanups here and there;
* A few simple bugfixes;
* Some more work in preparation for A000 family support;
* Add support for radiotap timestamps;
* Some work on our firmware debugging capabilities;
-----BEGIN PGP SIGNATURE-----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=6IIg
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2017-01-26' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
Some improvements, bugfixes and new features:
* A bunch of cleanups here and there;
* A few simple bugfixes;
* Some more work in preparation for A000 family support;
* Add support for radiotap timestamps;
* Some work on our firmware debugging capabilities;
This set of station id is redundant - it is being initialised
above.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When removing inactive queue - use the central disable queue
function. This is needed due to a000 changes to come, but is
a proper cleanup anyway.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The value returned from iwl_mvm_send_cmd_pdu() in this function is not
used and always returns an error (which is the whole point of the
call). Tag the ret variable with __maybe_unused to avoid this compile
warning when W=1 is used:
/home/luca/iwlwifi/stack-dev/drivers/net/wireless/intel/iwlwifi/mvm/debugfs.c: In function ‘iwl_dbgfs_fw_restart_write’:
/home/luca/iwlwifi/stack-dev/drivers/net/wireless/intel/iwlwifi/mvm/debugfs.c:875:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
int ret;
^
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When compiling with W=1, we get the following warning in debugfs.c:
/home/luca/iwlwifi/stack-dev/drivers/net/wireless/intel/iwlwifi/dvm/debugfs.c: In function ‘iwl_dbgfs_fw_restart_write’:
/home/luca/iwlwifi/stack-dev/drivers/net/wireless/intel/iwlwifi/dvm/debugfs.c:2313:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
int ret;
^
Fix it by ignoring the return value in this case.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Remove the sta_id variable, to avoid this compile warning when
compiling with W=1:
/home/luca/iwlwifi/stack-dev/drivers/net/wireless/intel/iwlwifi/mvm/sta.c: In function ‘iwl_mvm_change_queue_owner’:
/home/luca/iwlwifi/stack-dev/drivers/net/wireless/intel/iwlwifi/mvm/sta.c:871:5: warning: variable ‘sta_id’ set but not used [-Wunused-but-set-variable]
s8 sta_id;
^
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The return value from this function is never used, so make it return
void to avoid getting the following warning when compiling wiht W=1:
/home/luca/iwlwifi/stack-dev/drivers/net/wireless/intel/iwlwifi/dvm/rs.c: In function ‘rs_tl_turn_on_agg_for_tid’:
/home/luca/iwlwifi/stack-dev/drivers/net/wireless/intel/iwlwifi/dvm/rs.c:400:6: warning: variable ‘load’ set but not used [-Wunused-but-set-variable]
u32 load;
^
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
shift_param is defined and set in iwl_pcie_load_cpu_sections but not
used. Fix this to avoid -Wunused-but-set-variable warning.
The code using it turned into dead code with commit dcab8ecd56
("iwlwifi: mvm: support ucode load for family_8000 B0 only") which
added a separate function iwl_pcie_load_given_ucode_8000 (then 8000b)
for IWL_DEVICE_FAMILY_8000. Commit 76f8c0e17e ("iwlwifi: pcie:
remove dead code") removed the dead code but left shift_param as is.
iwlwifi/pcie/trans.c: In function ‘iwl_pcie_load_cpu_sections’:
iwlwifi/pcie/trans.c:871:6: warning: variable ‘shift_param’ set but not used [-Wunused-but-set-variable]
Fixes: dcab8ecd56 ("iwlwifi: mvm: support ucode load for family_8000 B0 only")
Fixes: 76f8c0e17e ("iwlwifi: pcie: remove dead code")
Signed-off-by: Kirtika Ruchandani <kirtika@google.com>
Cc: Sara Sharon <sara.sharon@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Liad Kaufman <liad.kaufman@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
[removed some unnecessary braces]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Commit 5fc0f76c4 introduced Rx stats from debugfs, the function
iwl_mvm_reset_frame_stats from that commit defines and sets mcs but
does not use it. Compiling iwlwifi with W=1 gives this warning -
iwlwifi/mvm/rs.c: In function ‘iwl_mvm_update_frame_stats’:
iwlwifi/mvm/rs.c:3074:14: warning: variable ‘mcs’ set but not used [-Wunused-but-set-variable]
Fixes: 5fc0f76c43 (iwlwifi: mvm: add Rx frames statistics via debugfs)
Signed-off-by: Kirtika Ruchandani <kirtika@google.com>
Cc: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
mvmvif is defined and set in rs_mimo_allow but not used. Compiling
iwlwifi with W=1 gives the following warning, remove it. mvmsta is
used only to obtain mvmvif so remove it as well.
iwlwifi/mvm/rs.c: In function 'rs_mimo_allow':
iwlwifi/mvm/rs.c:165:22: warning: variable 'mvmvif' set but not used.[-Wunused-but-set-variable]
This fix removes calls to iwl_mvm_sta_from_mac &
iwl_mvm_vif_from_mac. They are both accessors, and do not have any
side-effects. Commit e621c2282e ("iwlwifi: rs: Remove workaround
that disables MIMO on P2P") removed a workaround that disabled MIMO on
P2P, 'mvmvif' was used for that workaround, but not removed with it.
Fixes: e621c2282e ("iwlwifi: rs: Remove workaround that disables MIMO on P2P")
Signed-off-by: Kirtika Ruchandani <kirtika@google.com>
Cc: Alexander Bondar <alexander.bondar@intel.com>
Cc: Emmanuel Grumbach <emmmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The temperature variable is set but not used in
iwl_mvm_handle_statistics(). Remove it to avoid the following
compiler warning when W=1 is used:
/home/luca/iwlwifi/stack-dev/drivers/net/wireless/intel/iwlwifi/mvm/rx.c: In function ‘iwl_mvm_handle_rx_statistics’:
/home/luca/iwlwifi/stack-dev/drivers/net/wireless/intel/iwlwifi/mvm/rx.c:759:6: warning: variable ‘temperature’ set but not used [-Wunused-but-set-variable]
u32 temperature;
^
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
IWL6000G2B_UCODE_API_MAX is not defined. ucode_api_max of
IWL_DEVICE_6030 uses IWL6000G2_UCODE_API_MAX. Use this also for
MODULE_FIRMWARE.
Fixes: 9d9b21d1b6 ("iwlwifi: remove IWL_*_UCODE_API_OK")
Signed-off-by: Jürg Billeter <j@bitron.ch>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For 9000 devices withg upload, FW cannot send the entire phy
flags, and will send only the band - which is what we really
care about anyway. Change is backward compatible.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In preparation for the new TX cmd - move the rate calculation
to a diffrent function, and make it independent of the TX
command.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently the function changes the TX cmd itself.
Make it more generic by returning a value, as preperation
to the new TX cmd.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The maximum number of firmware sections is now 32 instead of 16 for
a000 devices. Set the appropriate define. Avoid out of bounds access
in case there are more sections than the maximum set by driver.
Make the driver extensible to FW size changes by allocating the
section memory dynamically.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The logic in the paging calculations is a bit hard to
follow. Replace it with a kernel define.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Some of the code there is duplicate while the only change is
the block size. Unifying it shortens the code and make the
difference clearer.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When copying from vmalloc'ed memory to the SG list, don't crash
if the transport didn't provide any data.
Fixes: 7e62a699aa ("iwlwifi: mvm: use dev_coredumpsg()")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Due to some new features and changes, the firmware file will now
specify what type of memory to dump, in upper 8 bits of the type
field of the TLV. Parse it (types we don't understand are errors)
and teach the code to dump periphery memory.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The return value is never used, so make the function void.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's no reason to be validating the memory dump types, or
checking them for duplication, or anything, since we really
just pass them through from the TLV to the dump.
Thus, change the way we handle memory dump TLVs to let the
driver just blindly use anything specified there, dumping it
into the memory dump output file.
This makes the system extensible without driver changes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For unified images, we shouldn't restart the HW if suspend fails. The
only reason for restarting the HW with non-unified images is to go
back to the D0 image.
Fixes: 23ae61282b ("iwlwifi: mvm: Do not switch to D3 image on suspend")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Set the relevant fields to export the 32-bit device timestamp to
radiotap using the new mac80211 infrastructure. This will be useful
to allow synchronising monitor captures taken on different hardware
simultaneously.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
These drivers use a set of complicated macros to extract and insert
information for the RX and TX descriptors. Driver rtl8192cu had a
different set than was used for the PCI-based drivers. To simplify
the code, rtl8192cu is switched to use the common version. In the
process, two errors in those common macros were found and fixed.
Besides simplifying the code, there is an additional benefit. We have
no BE hardware to test the PCI driver, but using the common macros
provides an additional test for the validity of many endian-sensitive
operations.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver requires a checksum for the descriptors so that the wifi
chip is assured that the USB transmission was correct. These entries
are little-endian, but the driver was always using cpu order in the
calculation. As a result, the driver failed on BE hardware.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The firmware is read from disk as a little-endian byte string. The code
that loads the firmware into the device transfers it as 4-byte quantities.
The routines that write multi-byte quantities on BE hardware assume that
the data are in CPU order, and automatically do the conversion to the LE
order required by the device. As a result, the firmware is transmitted
incorrectly. Rather than do multiple byte swaps on the data, the download
routine is revised to transmit bytes rather than dwords. Although the
number of I/O operations is increased, the firmware is not often loaded.
All drivers have the same bug, and use essentially the same code to
download firmware. These routines have been moved into rtlwifi.
Some CamelCase variables have been renamed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As the kernel provides access to module parameters through entries in
/sys/module/<driver>/parameters/, there is no need for a private
interface. Thus the existing code for setting the debug level is
removed.
Reported-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The debugging macros contain a parameter COMP_XX that could be used as a
mask; however, the code turns all these various bits on at the same time.
This change implements them as a proper mask, and adds module parameters
to set the mask at load time.
The current name "debug" for the debug level has been changed to
"debug_level" to better differentiate it from "debug_mask".
The debug routines have also been changed to interrogate the structure
that is loaded at entry time. As a result, the structure rtl_debug is no
longer needed, and all references to it are deleted.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These two debugging formss implement debugging using rather complicated
macro constructions. These are replaced with compiled code that is easier
to understand.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This intends to make init/attach process slightly easier to follow.
What driver was doing in brcmf_bus_start wasn't bus specific at all and
function brcmf_bus_stop wasn't undoing things done there. This function
is supposed to be called by bus specific code when the bus is ready.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Driver used to call brcmf_bus_detach only from one place and it already
contained a check for drvr not being NULL. We can get rid of this extra
function, call brcmf_bus_stop directly and simplify the code.
There also isn't brcmf_bus_attach function which one could expect so it
looks more consistent this way.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Function brcmf_c_set_joinpref_default is in common.c, so move it to the
related header.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Functions brcmf_c_prec_enq and brcmf_sdio_init don't exist so we
really don't need their declarations. Function brcmf_parse_tlvs is used
in cfg80211.c only so make it static and drop from header as well.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
brcmf_sdio_fromevntchan() was being called on the the data frame
rather than the software header, causing some frames to be
mischaracterized as on the event channel rather than the data channel.
This fixes a major performance regression (due to dropped packets). With
this patch the download speed jumped from 1Mbit/s back up to 40MBit/s due
to the sheer amount of packets being incorrectly processed.
Fixes: c56caa9db8 ("brcmfmac: screening firmware event packet")
Signed-off-by: Gavin Li <git@thegavinli.com>
Cc: <stable@vger.kernel.org> # 4.7+
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
[kvalo@codeaurora.org: improve commit logs based on email discussion]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These IDs originate from the vendor driver
Signed-off-by: Axel Köllhofer <AxelKoellhofer@web.de>
Signed-off-by: Jes Sorensen <Jes.Sorensen@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This was tested by David Patiño.
Reported-by: David Patiño <davidpatino82@gmail.com>
Signed-off-by: Axel Köllhofer <AxelKoellhofer@web.de>
Signed-off-by: Jes Sorensen <Jes.Sorensen@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Device reported as working fine, so tell the driver not to warn about
it being untested.
Reported-by: Aex Aey <aexaey@gmail.com>
Signed-off-by: Jes Sorensen <Jes.Sorensen@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Michael Schenk