The MAX44009 is a low-power ambient light sensor from Maxim
Integrated. It differs from the MAX44000 in that it doesn't have
proximity sensing and that it requires far less current (1 micro-amp
vs 5 micro-amps). The register mapping and feature set between the
two are different enough to require a new driver for the MAX44009.
Developed and tested with a BeagleBone Black and UDOO Neo (i.MX6SX)
Supported features:
* Reading lux (processed value)
* Rising and falling illuminance threshold
events
* Configuring integration time
https://datasheets.maximintegrated.com/en/ds/MAX44009.pdf
Signed-off-by: Robert Eshleman <bobbyeshleman@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The light sensor's power supply could be controllable by regulator
on some platforms, such as i.MX6Q-SABRESD board, the light sensor
isl29023's power supply is controlled by a GPIO fixed regulator,
need to make sure the regulator is enabled before any operation of
sensor, this patch adds vcc regulator operation support.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Along with the headline feature of 5 new drivers, we have the
substantial addition of auxilliary sensor support on the lsm6sdx
parts for ST. There has also been a good set of staging cleanup
in this period with more underway.
An ever increasing number of devices supported with just a new
ID which is a good sign that at least some manufacturers are
continuing to stabilise their interfaces.
New device support,
* ad7124
- New driver supporting Analog Devices' ad7124-4 and ad7124-8 parts
with the inevitable DT binding.
* ad7949
- New driver supporting Analog Devices' ad7949, AD7682 and AD7689 ADCs.
* rm3100
- New driver supporting PNIs RM3100 magnometer with bindings and
vendor prefix.
* ti-dac7311
- New driver supporting DAC7311, DAC6311 and DAC5311 TI DACs, with
DT bindings.
* vcnl5035
- New driver supporting the light sensor part of the VCNL4035, with
DT bindings
Features,
* bindings
- Add a generic ADC channel binding as we keep reinventing this
wheel.
* adc128s052
- Add IDs for additional pin compatible parts.
- Add APCI ID seen on E3940 UP squared boards.
* ad_sigma_delta
- Allow for custom data register overiding default.
* kxcjk1013
- Add KIOX0009 ACPI ID as seen on the Acer One 10.
* lsm6dsx
- Rework leading to...
- External sensor support using the built in I2C master.
- Initial support for a slave lis2mdl magnetometer.
* meson-saradc
- Add temperature sensor support and bindings.
* st_magn
- New ID for lsm9dsl_magn with bindings
- New ID for lis3de accelerometer
* tpl0102
- Add supprot for IIO_AVAIL_RANGE to report the range available
from this device to userspace and in kernel users.
Cleanups and minor fixes
* tools
- Allow outside specification of CFLAGS
* ad2s90
- Handle and spi_read error.
- Handle spi_setup failure
- Drop a pointless assignment.
- Prevent a potentail race by moving device registration to after
all other setup.
- Add missing scale attribute.
- Add a sanity check on channel type before trying to read it.
* ad2s1210
- Move to modern gpio descriptors.
- Drop a gpioin flag which made no sense as far as we can tell.
- Add dt table (bindings doc to follow when this is ready for
moving out of staging).
* ad5933
- Drop camel-case naming of ext_clk_hz.
- White space fixes.
* ad7150
- Local variable to shorten overly long line.
- Alignment and line break fixes.
* ad7280a
- Handle an error path that was previously ignored.
- Use crc8.h to build the crc table replacing custom code.
- Avoid unecessary cast.
- Power down the device if an error happens in probe
- Use devm routines to simplify probe and remove.
* ad7606
- Alignment fixes.
* ad7780
- This worked as long as by coincidence an uninitialized value
was 0. Lets not rely on that.
- Ensure gain update is only used with the ad778x chips that
actually support it.
- Tidy up pattern mask generation.
- Read regulator when scale is requested (which should be infrequent)
as it might have changed from initialization.
* ad7816
- Move to modern gpio descriptors
- Don't use a busy_pin for ad7818 as there isn't one.
- Ensure RD/WR and CONVST pins are outputs (previously they
were brought up as inputs which doesn't seem to make any sense)
- DT id table.
* adc128s052
- SPDX
* adt7316
- Alignment fix.
- Fix data reading. When using I2C the driver never actually
used the value read. This has been broken a very long time
hence no rush to fix it now + the driver is undergoing a lot
of cleanup.
- Sanity check that the i2c read didn't fail to actually read
anything.
* dpot-dac
- Mark a switch full through with slightly different text so that
gcc doesn't warn on it.
* gyro-adc
- Fix a wrong file in the MAINTAINERS entry and add binding doc to the
listed files.
* ina2xx
- Add some early returns to clarify error paths in switch.
* lsm6dsx
- MAINTAINERS entry.
* max11100
- SPDX
* max9611
- SPDX
* mcp4131
- use of_device_get_match_data in preference to spi_get_device_id
approach.
* rcar-adc
- SPDX
* sc27xx
- Add ADC conversion timeout support to avoid possible fault.
* ssp_sensors
- Don't free managed resources manually.
* st-magn
- Add a comment to avoid future confusion over when to use -magn
postfix (on multi chip in package parts)
- Add BDU register for LIS3MDL where it seems to have been missed.
* st-sensors
- Minor spelling, grammar etc fixes.
* tpl0102
- Use a pointer rather than an index of an array to improve conciseness.
-----BEGIN PGP SIGNATURE-----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=78Y3
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.21a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-testing
Jonathan writes:
First set of new device support, features and cleanups for IIO in the 4.21 cycle
Along with the headline feature of 5 new drivers, we have the
substantial addition of auxilliary sensor support on the lsm6sdx
parts for ST. There has also been a good set of staging cleanup
in this period with more underway.
An ever increasing number of devices supported with just a new
ID which is a good sign that at least some manufacturers are
continuing to stabilise their interfaces.
New device support,
* ad7124
- New driver supporting Analog Devices' ad7124-4 and ad7124-8 parts
with the inevitable DT binding.
* ad7949
- New driver supporting Analog Devices' ad7949, AD7682 and AD7689 ADCs.
* rm3100
- New driver supporting PNIs RM3100 magnometer with bindings and
vendor prefix.
* ti-dac7311
- New driver supporting DAC7311, DAC6311 and DAC5311 TI DACs, with
DT bindings.
* vcnl5035
- New driver supporting the light sensor part of the VCNL4035, with
DT bindings
Features,
* bindings
- Add a generic ADC channel binding as we keep reinventing this
wheel.
* adc128s052
- Add IDs for additional pin compatible parts.
- Add APCI ID seen on E3940 UP squared boards.
* ad_sigma_delta
- Allow for custom data register overiding default.
* kxcjk1013
- Add KIOX0009 ACPI ID as seen on the Acer One 10.
* lsm6dsx
- Rework leading to...
- External sensor support using the built in I2C master.
- Initial support for a slave lis2mdl magnetometer.
* meson-saradc
- Add temperature sensor support and bindings.
* st_magn
- New ID for lsm9dsl_magn with bindings
- New ID for lis3de accelerometer
* tpl0102
- Add supprot for IIO_AVAIL_RANGE to report the range available
from this device to userspace and in kernel users.
Cleanups and minor fixes
* tools
- Allow outside specification of CFLAGS
* ad2s90
- Handle and spi_read error.
- Handle spi_setup failure
- Drop a pointless assignment.
- Prevent a potentail race by moving device registration to after
all other setup.
- Add missing scale attribute.
- Add a sanity check on channel type before trying to read it.
* ad2s1210
- Move to modern gpio descriptors.
- Drop a gpioin flag which made no sense as far as we can tell.
- Add dt table (bindings doc to follow when this is ready for
moving out of staging).
* ad5933
- Drop camel-case naming of ext_clk_hz.
- White space fixes.
* ad7150
- Local variable to shorten overly long line.
- Alignment and line break fixes.
* ad7280a
- Handle an error path that was previously ignored.
- Use crc8.h to build the crc table replacing custom code.
- Avoid unecessary cast.
- Power down the device if an error happens in probe
- Use devm routines to simplify probe and remove.
* ad7606
- Alignment fixes.
* ad7780
- This worked as long as by coincidence an uninitialized value
was 0. Lets not rely on that.
- Ensure gain update is only used with the ad778x chips that
actually support it.
- Tidy up pattern mask generation.
- Read regulator when scale is requested (which should be infrequent)
as it might have changed from initialization.
* ad7816
- Move to modern gpio descriptors
- Don't use a busy_pin for ad7818 as there isn't one.
- Ensure RD/WR and CONVST pins are outputs (previously they
were brought up as inputs which doesn't seem to make any sense)
- DT id table.
* adc128s052
- SPDX
* adt7316
- Alignment fix.
- Fix data reading. When using I2C the driver never actually
used the value read. This has been broken a very long time
hence no rush to fix it now + the driver is undergoing a lot
of cleanup.
- Sanity check that the i2c read didn't fail to actually read
anything.
* dpot-dac
- Mark a switch full through with slightly different text so that
gcc doesn't warn on it.
* gyro-adc
- Fix a wrong file in the MAINTAINERS entry and add binding doc to the
listed files.
* ina2xx
- Add some early returns to clarify error paths in switch.
* lsm6dsx
- MAINTAINERS entry.
* max11100
- SPDX
* max9611
- SPDX
* mcp4131
- use of_device_get_match_data in preference to spi_get_device_id
approach.
* rcar-adc
- SPDX
* sc27xx
- Add ADC conversion timeout support to avoid possible fault.
* ssp_sensors
- Don't free managed resources manually.
* st-magn
- Add a comment to avoid future confusion over when to use -magn
postfix (on multi chip in package parts)
- Add BDU register for LIS3MDL where it seems to have been missed.
* st-sensors
- Minor spelling, grammar etc fixes.
* tpl0102
- Use a pointer rather than an index of an array to improve conciseness.
* tag 'iio-for-4.21a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (80 commits)
Staging: iio: adt7316: Add an extra check for 'ret' equals to 0
Staging: iio: adt7316: Fix i2c data reading, set the data field
dt-bindings: iio: adc: Add docs for ad7124
iio: adc: Add ad7124 support
dt-bindings: iio: adc: Add common ADCs properties to a separate file
iio: ad_sigma_delta: Allow to provide custom data register address
staging: iio: ad7816: Add device tree table.
iio: imu: st_lsm6dsx: add entry in MAINTAINERS file
iio: potentiometer: mcp4131: use of_device_get_match_data()
staging: iio: adc: ad7280a: use devm_* APIs
staging: iio: adc: ad7280a: power down the device on error in probe
dt-bindings: iio: imu: st_lsm6dsx: add support to i2c pullup resistors
iio: imu: st_lsm6dsx: add hw FIFO support to i2c controller
iio: imu: st_lsm6dsx: add st_lsm6dsx_push_tagged_data routine
iio: imu: st_lsm6dsx: add i2c embedded controller support
iio: imu: st_lsm6dsx: introduce st_lsm6dsx_sensor_set_enable routine
iio: imu: st_lsm6dsx: introduce ST_LSM6DSX_ID_EXT sensor ids
iio: imu: st_lsm6dsx: remove static from st_lsm6dsx_set_watermark
iio: imu: st_lsm6dsx: reload trimming parameter at bootstrap
iio: imu: st_lsm6dsx: introduce locked read/write utility routines
...
Add support for VCNL4035, which is capable of Ambient light
sensing (ALS) and proximity function. This patch adds support
only for ALS function
Signed-off-by: Parthiban Nallathambi <pn@denx.de>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Before this commit sensor_hub_input_attr_get_raw_value() failed to take
the signedness of 16 and 8 bit values into account, returning e.g.
65436 instead of -100 for the z-axis reading of an accelerometer.
This commit adds a new is_signed parameter to the function and makes all
callers pass the appropriate value for this.
While at it, this commit also fixes up some neighboring lines where
statements were needlessly split over 2 lines to improve readability.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Here is the big staging and IIO driver pull request for 4.20-rc1.
There are lots of things here, we ended up adding more lines than
removing, thanks to a large influx of Comedi National Instrument device
support. Someday soon we need to get comedi out of staging...
Other than the comedi drivers, the "big" things here are:
- new iio drivers
- delete dgnc driver (no one used it and no one had the hardware
anymore)
- vbox driver updates and fixes
- erofs fixes
- tons and tons of tiny checkpatch fixes for almost all staging
drivers
All of these have been in linux-next, with the last few happening a bit
"late" due to them getting stuck on my laptop during travel to the
Mantainers summit.
When merging with your tree, there will be 2 merge conflicts, both files
will be simple to resolve, just delete them :)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW9bSGA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yk5eACfYp73m9tLO22rnBcXJ73bWAYSTOMAn2GEL4Nc
LZBXs8QvvJIwfqmi7ofn
=UWJn
-----END PGP SIGNATURE-----
Merge tag 'staging-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO driver updates from Greg KH:
"Here is the big staging and IIO driver pull request for 4.20-rc1.
There are lots of things here, we ended up adding more lines than
removing, thanks to a large influx of Comedi National Instrument
device support. Someday soon we need to get comedi out of staging...
Other than the comedi drivers, the "big" things here are:
- new iio drivers
- delete dgnc driver (no one used it and no one had the hardware
anymore)
- vbox driver updates and fixes
- erofs fixes
- tons and tons of tiny checkpatch fixes for almost all staging
drivers
All of these have been in linux-next, with the last few happening a
bit "late" due to them getting stuck on my laptop during travel to the
Mantainers summit"
* tag 'staging-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (690 commits)
staging: gasket: Fix sparse "incorrect type in assignment" warnings.
staging: gasket: remove debug logs for callback invocation
staging: gasket: remove debug logs in page table mapping calls
staging: rtl8188eu: core: Use sizeof(*p) instead of sizeof(struct P) for memory allocation
staging: ks7010: Remove extra blank line
staging: gasket: Remove extra blank line
staging: media: davinci_vpfe: Fix spelling mistake in enum
staging: speakup: Add a pair of braces
staging: wlan-ng: Replace long int with long
staging: MAINTAINERS: remove obsolete IPX staging directory
staging: MAINTAINERS: remove NCP filesystem entry
staging: rtl8188eu: cleanup comparsions to false
staging: gasket: Update device virtual address comment
staging: gasket: sysfs: fix attribute release comment
staging: gasket: apex: fix sysfs_show
staging: gasket: page_table: simplify gasket_components_to_dev_address
staging: gasket: page_table: fix comment in components_to_dev_address
staging: gasket: page table: fixup error path allocating coherent mem
staging: gasket: page_table: rearrange gasket_page_table_entry
staging: gasket: page_table: remove unnecessary PTE status set to free
...
Add device tree support for ROHM BH1750 series ambient light sensors.
Signed-off-by: ryang <decatf@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Relying on CONFIG_PM_SLEEP to set PM ops is not necessary
since core will handle everything internally. One have to only make sure
that functions that can go unused are marked with __maybe_unused.
Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Drop boilerplate license text and use SPDX identifier instead.
Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Split regmap_config.use_single_rw into use_single_read and
use_single_write. This change enables drivers of devices which only
support bulk operations in one direction to use the regmap_bulk_*()
functions for both directions and have their bulk operation split into
single operations only when necessary.
Update all struct regmap_config instances where use_single_rw==true to
instead set both use_single_read and use_single_write. No attempt was
made to evaluate whether it is possible to set only one of
use_single_read or use_single_write.
Signed-off-by: David Frey <dpfrey@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Variable max44000_alstim_shift is defined but is never used hence it is
redundant and can be removed. This variable has been like this since
the driver was added back in 2016.
Cleans up clang warning:
warning: 'max44000_alstim_shift' defined but not used [-Wunused-const-variable=]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch adds support for the regulator framework to the tsl2772
driver. Driver was tested using a LG Nexus 5 (hammerhead) phone with
the two regulators and on a Raspberry Pi 2 without any regulators
controlling the power to the sensor.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch adds support for optionally reading the proximity led diode
and current settings from device tree. This was tested using a LG
Nexus 5 (hammerhead) which requires a different diode than the driver
default for the IR LED.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Read response register to detect any error.
Signed-off-by: Maxime Roussin-Bélanger <maxime.roussinbelanger@gmail.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The current check on val always results in true and so the
call to sii1133_update_adcsens never gets called. Fix this check
so it returns with -EINVAL only when val is not zero and not one.
Detected by CoverityScan, CID#1472099 ("Logically dead code")
Fixes: e01e7eaf37 ("iio: light: introduce si1133")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
VCNL4200 is an integrated long distance (up to 1500mm) proximity and
ambient light sensor.
The support is very basic. There is no configuration of proximity and
ambient light sensing yet. Only the reading of both measured values is
done.
The reading of ambient light and proximity values is blocking. If you
request a new value too early, the driver waits for new value to be
ready.
Signed-off-by: Tomas Novotny <tomas@novotny.cz>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
We can detect incorrectly specified device id for some chips, so warn
user in that case.
Signed-off-by: Tomas Novotny <tomas@novotny.cz>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The driver already supports VCNL4010/20 devices. The currently supported
features and detectable product id are the same, so add shared id for
them.
This is a groundwork to extend the driver by detecting incorrectly
specified device id.
Signed-off-by: Tomas Novotny <tomas@novotny.cz>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There are similar chips in the vcnl4xxx family. The initialization and
communication is a bit different for members of the family, so this
patch makes the driver extendable for different chips.
There is no functional change.
Signed-off-by: Tomas Novotny <tomas@novotny.cz>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There are also a couple of fixes that can wait for the coming merge
window.
Core new features
* Support for phase channels (used in time of flight sensors amongst
other things)
* Support for deep UV light channel modifier.
New Device Support
* AD4758 DAC
- New driver and dt bindings.
* adxl345
- Support the adxl375 +-200g part which is register compatible.
* isl29501 Time of flight sensor.
- New driver
* meson-saradc
- Support the Meson8m2 Socs - right now this is just an ID, but there will
be additional difference in future.
* mpu6050
- New ID for 6515 variant.
* si1133 UV sensor.
- New driver
* Spreadtrum SC27xx PMIC ADC
- New driver and dt bindings.
Features
* adxl345
- Add calibration offset readback and writing.
- Add sampling frequency control.
Fixes and Cleanups
* ad5933
- Use a macro for the channel definition to reduce duplication.
* ad9523
- Replace use of core mlock with a local lock. Part of ongoing efforts
to avoid confusing the purpose of mlock which is only about iio core
state changes.
- Fix displayed phase which was out by a factor of 10.
* adxl345
- Add a link to the datasheet.
- Rework the use of the address field in the chan_spec structures to
allow addition of more per channel information.
* adis imu
- Mark switch fall throughs.
* at91-sama5d2
- Fix some casting on big endian systems.
* bmp280
- Drop some DT elements that aren't used and should mostly be done from
userspace rather than in DT.
* hx711
- add clock-frequency dt binding and resulting delay to deal with capacitance
issue on some boards.
- fix a spurious unit-address in the example.
* ina2xx
- Avoid a possible kthread_stop with a stale task_struct.
* ltc2632
- Remove some unused local variables (assigned but value never used).
* max1363
- Use device_get_match_data to remove some boilerplate.
* mma8452
- Mark switch fall throughs.
* sca3000
- Fix a missing return in a switch statement (a bad fallthrough
previously!)
* sigma-delta-modulator
- Drop incorrect unit address from the DT example.
* st_accel
- Use device_get_match_data to drop some boiler plate.
- Move to probe_new for i2c driver as second parameter not used.
* st_sensors library
- Use a strlcpy (safe in this case).
* st_lsm6dsx
- Add some error logging.
* ti-ads7950
- SPDX
- Allow simultaneous buffered and polled reads. Needed on a Lego Mindstorms
EV3 where some channels are used for power supply monitoring at a very low
rate.
* ti-dac5571
- Remove an unused variable.
* xadc
- Drop some dead code.
-----BEGIN PGP SIGNATURE-----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=T+hS
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.19b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of IIO new device support, features and cleanups.
There are also a couple of fixes that can wait for the coming merge
window.
Core new features
* Support for phase channels (used in time of flight sensors amongst
other things)
* Support for deep UV light channel modifier.
New Device Support
* AD4758 DAC
- New driver and dt bindings.
* adxl345
- Support the adxl375 +-200g part which is register compatible.
* isl29501 Time of flight sensor.
- New driver
* meson-saradc
- Support the Meson8m2 Socs - right now this is just an ID, but there will
be additional difference in future.
* mpu6050
- New ID for 6515 variant.
* si1133 UV sensor.
- New driver
* Spreadtrum SC27xx PMIC ADC
- New driver and dt bindings.
Features
* adxl345
- Add calibration offset readback and writing.
- Add sampling frequency control.
Fixes and Cleanups
* ad5933
- Use a macro for the channel definition to reduce duplication.
* ad9523
- Replace use of core mlock with a local lock. Part of ongoing efforts
to avoid confusing the purpose of mlock which is only about iio core
state changes.
- Fix displayed phase which was out by a factor of 10.
* adxl345
- Add a link to the datasheet.
- Rework the use of the address field in the chan_spec structures to
allow addition of more per channel information.
* adis imu
- Mark switch fall throughs.
* at91-sama5d2
- Fix some casting on big endian systems.
* bmp280
- Drop some DT elements that aren't used and should mostly be done from
userspace rather than in DT.
* hx711
- add clock-frequency dt binding and resulting delay to deal with capacitance
issue on some boards.
- fix a spurious unit-address in the example.
* ina2xx
- Avoid a possible kthread_stop with a stale task_struct.
* ltc2632
- Remove some unused local variables (assigned but value never used).
* max1363
- Use device_get_match_data to remove some boilerplate.
* mma8452
- Mark switch fall throughs.
* sca3000
- Fix a missing return in a switch statement (a bad fallthrough
previously!)
* sigma-delta-modulator
- Drop incorrect unit address from the DT example.
* st_accel
- Use device_get_match_data to drop some boiler plate.
- Move to probe_new for i2c driver as second parameter not used.
* st_sensors library
- Use a strlcpy (safe in this case).
* st_lsm6dsx
- Add some error logging.
* ti-ads7950
- SPDX
- Allow simultaneous buffered and polled reads. Needed on a Lego Mindstorms
EV3 where some channels are used for power supply monitoring at a very low
rate.
* ti-dac5571
- Remove an unused variable.
* xadc
- Drop some dead code.
e-mail received from Silicon Lab to confirm that the licensing
isn't a problem.
"
Dear Maxime Roussin-Belanger,
The LUX calculation code only works with Si1133.
As long as the software is used with Silicon Lab's sensor product,
I don't see any problem.
Regards,
Tony
"
Signed-off-by: Maxime Roussin-Bélanger <maxime.roussinbelanger@gmail.com>
Reviewed-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It may be possible for tsl2772_get_lux to return a zero lux value
and hence a division by zero can occur when lux_val is zero. Check
for this case and return -ERANGE to avoid the division by zero.
Detected by CoverityScan, CID#1469484 ("Division or modulo by zero")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The times reported by the in_illuminance_integration_time_available
sysfs attribute are actually in milliseconds, not microseconds. This
patch corrects the times with the correct unit.
The fixes tag is inaccurate as the issue existed when the driver
was still in staging. However, lots of changes occured before
it graduated so this is as a good a point as any for backports.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Fixes: f44d5c8ac3 ("staging: iio: tsl2583: move out of staging")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move the tsl2772 driver out of staging and into mainline.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Similar to other common iio frameworks, move cros_ec_sensors_core.h from
drivers/iio/common/cros_ec_sensors/ to include/linux/iio/common.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Usually, functions responsible for reading raw data typically relies on
values from iio_chan_info_enum to correctly identify the type of data to
be read. There is a set of a device driver that uses the magic number 0
instead of IIO_CHAN_INFO_RAW. This patch improves the readability by
replaces the magic number 0 for the appropriate IIO_CHAN_INFO_RAW in six
devices driver in the IIO subsystem.
Signed-off-by: Rodrigo Siqueira <rodrigosiqueiramelo@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch adds support for the On Semiconductor LV0104CS ambient
light sensor.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
If an application set a tight sampling frequency, given the interrupt
use is a wakeup source, suspend will not happen: the kernel will receive
a wake up interrupt and will cancel the suspend process.
Given cros_ec sensors type is non wake up, this patch adds prepare and
complete callbacks to set 1s sampling period just before suspend. This
ensures the sensor hub will not be a source of interrupt during the
suspend process.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add GPLv2+ SPDX identifier and update email for author's drivers.
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Structures st_uvis25_i2c_regmap_config and st_uvis25_spi_regmap_config are
local to the source and do not need to be in global scope, so make them
both static.
Cleans up sparse warnings:
warning: symbol 'st_uvis25_i2c_regmap_config' was not declared. Should
it be static?
warning: symbol 'st_uvis25_spi_regmap_config' was not declared. Should
it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
add support for STMicroelectronics UVIS25 uv sensor
http://www.st.com/resource/en/datasheet/uvis25.pdf
- continuos mode support
- i2c support
- spi support
- trigger mode support
- system PM support
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Driver for 20-bit ALS and UV B sensor with I2C interface exposing
the following API:
in_uvindex_input
in_illuminance_raw
in_illuminance_scale
in_illuminance_scale_available
in_intensity_uv_raw
in_intensity_uv_scale
in_intensity_uv_scale_available
integration_time
integration_time_available
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix gcc warnings about variable 'ec_device' being set but not used
in these files:
common/cros_ec_sensors/cros_ec_sensors.c:194:25
light/cros_ec_light_prox.c:184:25
Signed-off-by: Paolo Cretaro <paolocretaro@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Here is the "big" staging and IIO driver update for 4.15-rc1.
Lots and lots of little changes, almost all minor code cleanups as the
Outreachy application process happened during this development cycle.
Also happened was a lot of IIO driver activity, and the typec USB code
moving out of staging to drivers/usb (same commits are in the USB tree
on a persistent branch to not cause merge issues.)
Overall, it's a wash, I think we added a few hundred more lines than
removed, but really only a few thousand were modified at all.
All of these have been in linux-next for a while. There might be a
merge issue with Al's vfs tree in the pi433 driver (take his changes,
they are always better), and the media tree with some of the odd atomisp
cleanups (take the media tree's version).
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWgnFrg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymxbwCgtNlBkqD2JJYpLRKvI/C4w1vzZsEAnA2THRkt
g3ioPBqmqC/2DSbldr2o
=/ebw
-----END PGP SIGNATURE-----
Merge tag 'staging-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging and IIO updates from Greg KH:
"Here is the "big" staging and IIO driver update for 4.15-rc1.
Lots and lots of little changes, almost all minor code cleanups as the
Outreachy application process happened during this development cycle.
Also happened was a lot of IIO driver activity, and the typec USB code
moving out of staging to drivers/usb (same commits are in the USB tree
on a persistent branch to not cause merge issues.)
Overall, it's a wash, I think we added a few hundred more lines than
removed, but really only a few thousand were modified at all.
All of these have been in linux-next for a while. There might be a
merge issue with Al's vfs tree in the pi433 driver (take his changes,
they are always better), and the media tree with some of the odd
atomisp cleanups (take the media tree's version)"
* tag 'staging-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (507 commits)
staging: lustre: add SPDX identifiers to all lustre files
staging: greybus: Remove redundant license text
staging: greybus: add SPDX identifiers to all greybus driver files
staging: ccree: simplify ioread/iowrite
staging: ccree: simplify registers access
staging: ccree: simplify error handling logic
staging: ccree: remove dead code
staging: ccree: handle limiting of DMA masks
staging: ccree: copy IV to DMAable memory
staging: fbtft: remove redundant initialization of buf
staging: sm750fb: Fix parameter mistake in poke32
staging: wilc1000: Fix bssid buffer offset in Txq
staging: fbtft: fb_ssd1331: fix mirrored display
staging: android: Fix checkpatch.pl error
staging: greybus: loopback: convert loopback to use generic async operations
staging: greybus: operation: add private data with get/set accessors
staging: greybus: loopback: Fix iteration count on async path
staging: greybus: loopback: Hold per-connection mutex across operations
staging: greybus/loopback: use ktime_get() for time intervals
staging: fsl-dpaa2/eth: Extra headroom in RX buffers
...
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The reported scale was only correct for the default settings of 100 ms
integration time and gain 1.
This aligns the reported scale with the behaviour of any other IIO driver
and the documented ABI, but may require userspace changes if someone uses
non-default settings.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Instead of manually iterating the array of allowed gain values, use
find_closest. Storing the current gain setting avoids accessing the
hardware on each query.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Instead of reading the value from the register on each query, store the
set value.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This improves code uniformity (range checks for als_gain are also done
in the setter). Also unmangle rounding and calculation of register value.
The calculated integration time it_ms is required in the next patch of
the series.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The TCS3472 device provides interrupt signal for out-of-threshold events
with persistence filter.
This change adds interrupt support for the threshold events and enables
to configure the period of time by persistence filter.
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The equivalent of both of these are now done via macro magic when
the relevant register calls are made. The actual structure
elements will shortly go away.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
New device support:
* ak8974
- support the AMI306.
* st_magnetometer
- add support for the LIS2MDL with bindings.
* rockchip-saradc
- add binding for rv1108 SoC (no driver change).
* srf08
- add srf02 (i2c only) and srf10 support.
* stm32-timer
- support for the STM32H7 to existing driver.
Features:
* tools
- move over to the tools buildsystem rather than hand rolling.
- add an install section to the build.
* ak8974
- use serial number to add device randomness.
- add AMI306 calibration data output.
* ccs811
- triggered buffer support.
* srf08
- add a device tree table as the old style i2c probing is going away,
- add triggered buffer support
* st32-adc
- add optional st,min-sample-time-nsecs binding to allow control of
sampling against analog circuitry.
* stm32-timer
- add output compare triggers.
* ti-ads1015
- add threshold event support.
* ti-ads7950
- Allow use on ACPI platforms including providing a default reference
voltage as there is no way to obtain this on ACPI currently.
Cleanup and fixes:
* ad7606
- fix an error return code in probe.
* ads1015
- fix incorrect data rate setting update when capture in progress,
- fix wrong scale information for the ADS1115,
- make conversions work when CONFIG_PM is not set,
- make sure we don't get a stale result after a runtime resume by
ensuring we wait long enough,
- avoid returning a false error form the buffer setup callbacks,
- add enough wait time to get the correct conversion,
- remove an unnecessary config register update,
- add a helper to set conversion mode reducing repeated boilerplate,
- use devm_iio_triggered_buffer_setup to simplify error and remove
paths,
- use iio_device_claim_direct_mode instead of opencoding the same.
* ak8974
- mark the INT_CLEAR register as precious to prevent debugfs access.
* apds9300
- constify the i2c_device_id.
* at91-sama5 adc
- add missing Kconfig dependency.
* bma180 accel
- constify the i2c_device_id.
* rockchip_saradc
- explicitly request exclusive reset control as part of the reset rework
on going throughout the kernel.
* st_accel
- fix drdy configuration for a load of accelerometers that only have
the int1 line. Fix is unimportant as presumably no deviec tree actually
used the non existent hardware line.
* st_pressure
- fix drdy configuration for LPS22HB and LPS25H by dropping int2 support
as they don't have this. Fix is unimportant as presumably no device tree
actually used the non existent hardware line.
* stm32-dac
- explicitly request exclusive reset control (part of reset being reworked).
* tsl2583
- constify the i2c_device_id.
* xadc
- coding style fixes.
-----BEGIN PGP SIGNATURE-----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=b6g8
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.14b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of IIO new device support, features and cleanup for the 4.14 cycle.
New device support:
* ak8974
- support the AMI306.
* st_magnetometer
- add support for the LIS2MDL with bindings.
* rockchip-saradc
- add binding for rv1108 SoC (no driver change).
* srf08
- add srf02 (i2c only) and srf10 support.
* stm32-timer
- support for the STM32H7 to existing driver.
Features:
* tools
- move over to the tools buildsystem rather than hand rolling.
- add an install section to the build.
* ak8974
- use serial number to add device randomness.
- add AMI306 calibration data output.
* ccs811
- triggered buffer support.
* srf08
- add a device tree table as the old style i2c probing is going away,
- add triggered buffer support
* st32-adc
- add optional st,min-sample-time-nsecs binding to allow control of
sampling against analog circuitry.
* stm32-timer
- add output compare triggers.
* ti-ads1015
- add threshold event support.
* ti-ads7950
- Allow use on ACPI platforms including providing a default reference
voltage as there is no way to obtain this on ACPI currently.
Cleanup and fixes:
* ad7606
- fix an error return code in probe.
* ads1015
- fix incorrect data rate setting update when capture in progress,
- fix wrong scale information for the ADS1115,
- make conversions work when CONFIG_PM is not set,
- make sure we don't get a stale result after a runtime resume by
ensuring we wait long enough,
- avoid returning a false error form the buffer setup callbacks,
- add enough wait time to get the correct conversion,
- remove an unnecessary config register update,
- add a helper to set conversion mode reducing repeated boilerplate,
- use devm_iio_triggered_buffer_setup to simplify error and remove
paths,
- use iio_device_claim_direct_mode instead of opencoding the same.
* ak8974
- mark the INT_CLEAR register as precious to prevent debugfs access.
* apds9300
- constify the i2c_device_id.
* at91-sama5 adc
- add missing Kconfig dependency.
* bma180 accel
- constify the i2c_device_id.
* rockchip_saradc
- explicitly request exclusive reset control as part of the reset rework
on going throughout the kernel.
* st_accel
- fix drdy configuration for a load of accelerometers that only have
the int1 line. Fix is unimportant as presumably no deviec tree actually
used the non existent hardware line.
* st_pressure
- fix drdy configuration for LPS22HB and LPS25H by dropping int2 support
as they don't have this. Fix is unimportant as presumably no device tree
actually used the non existent hardware line.
* stm32-dac
- explicitly request exclusive reset control (part of reset being reworked).
* tsl2583
- constify the i2c_device_id.
* xadc
- coding style fixes.
i2c_device_id are not supposed to change at runtime. All functions
working with i2c_device_id provided by <linux/i2c.h> work with
const i2c_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
i2c_device_id are not supposed to change at runtime. All functions
working with i2c_device_id provided by <linux/i2c.h> work with
const i2c_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
* ad2s1210
- Fix negative angular velocity reads (identified by a gcc 7 warning)
* aspeed-adc
- Wait for initialization sequence to finish before enabling channels.
Without it no channels work.
* axp288
- Revert a patch that dropped some bogus register mods. No one is entirely
sure why but it breaks charging on some devices.
- Fix GPADC pin read returning 0. Turns out a small sleep is needed.
* bmc150
- Make sure device is restored to normal state after suspend / resume
cycle. Otherwise, simple sysfs reads are broken.
* tsl2563
- fix wrong event code.
* st-accel
- add spi 3-wire support. Needed to fix the lsm303agr accelerometer
which only had 3 wires in all cases. Side effect is to enable optional
3-wire support for other devices.
* st-pressure
- disable multiread by default for LPS22HB (only effects SPI)
* sun4i-gpadc-iio
- fix unbalanced irq enable / disable
* vf610
- Fix VALT slection for REFSEL bits - ensures we are using the
right reference pins.
-----BEGIN PGP SIGNATURE-----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=BApO
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.13a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO fixes for the 4.13 cycle.
* ad2s1210
- Fix negative angular velocity reads (identified by a gcc 7 warning)
* aspeed-adc
- Wait for initialization sequence to finish before enabling channels.
Without it no channels work.
* axp288
- Revert a patch that dropped some bogus register mods. No one is entirely
sure why but it breaks charging on some devices.
- Fix GPADC pin read returning 0. Turns out a small sleep is needed.
* bmc150
- Make sure device is restored to normal state after suspend / resume
cycle. Otherwise, simple sysfs reads are broken.
* tsl2563
- fix wrong event code.
* st-accel
- add spi 3-wire support. Needed to fix the lsm303agr accelerometer
which only had 3 wires in all cases. Side effect is to enable optional
3-wire support for other devices.
* st-pressure
- disable multiread by default for LPS22HB (only effects SPI)
* sun4i-gpadc-iio
- fix unbalanced irq enable / disable
* vf610
- Fix VALT slection for REFSEL bits - ensures we are using the
right reference pins.
Set up and use triggered buffer if there is irq defined for device in
device tree. Trigger producer triggers from rpr0521 drdy interrupt line.
Trigger consumer reads rpr0521 data to scan buffer.
Depends on previous commits of _scale and _offset.
Signed-off-by: Mikko Koivunen <mikko.koivunen@fi.rohmeurope.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Robert Eshleman