Use of "unsigned int" is preferred to bare "unsigned" in net tree.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_enter_quickack_mode() already calls tcp_incr_quickack() and sets
icsk->icsk_ack.ato to TCP_ATO_MIN. This patch removes the duplication.
Signed-off-by: Vijay Subramanian <subramanian.vijay@gmail.com>
Reviewed-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Updates some comments to track RFC6298
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: H.K. Jerry Chu <hkchu@google.com>
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix bluetooth userland regression reported by Keith Packard, from
Gustavo Padovan.
2) Revert ath9k PS idle change, from Sujith Manoharan.
3) Correct default TCP memory limits (again), from Eric Dumazet.
4) Fix tcp_rcv_rtt_update() accidental use of unscaled RTT, from Neal
Cardwell.
5) We made a facility for layers like wireless to say how much tailroom
they need in the SKB for link layer stuff such as wireless
encryption etc., but TCP works hard to fill every SKB out to the end
defeating this specification.
This leads to every TCP packet getting reallocated by the wireless
code in order to have the right amount of tailroom available.
Fix TCP to only fill SKBs out to the real amount of data area it
asked for during the allocation, this way it won't eat into the
slack added for the device's tailroom needs.
Reported by Marc Merlin and fixed by Eric Dumazet.
6) Leaks, endian bugs, and new device IDs in bluetooth from Santosh
Nayak, João Paulo Rechi Vita, Cho, Yu-Chen, Andrei Emeltchenko,
AceLan Kao, and Andrei Emeltchenko.
7) OOPS on tty_close fix in bluetooth's hci_ldisc from Johan Hovold.
8) netfilter erroneously scales TCP window twice, fix from Changli Gao.
9) Memleak fix in wext-core from Julia Lawall.
10) Consistently handle invalid TCP packets in ipv4 vs. ipv6 conntrack,
from Jozsef Kadlecsik.
11) Validate IP header length properly in netfilter conntrack's
ipv4_get_l4proto().
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (39 commits)
NFC: Fix the LLCP Tx fragmentation loop
rtlwifi: Add missing DMA buffer unmapping for PCI drivers
rtlwifi: Preallocate USB read buffers and eliminate kalloc in read routine
tcp: avoid order-1 allocations on wifi and tx path
net: allow pskb_expand_head() to get maximum tailroom
bridge: Do not send queries on multicast group leaves
MAINTAINERS: Mark NATSEMI driver as orphan'd.
tcp: fix tcp_rcv_rtt_update() use of an unscaled RTT sample
tcp: restore correct limit
Revert "ath9k: fix going to full-sleep on PS idle"
rt2x00: Fix rfkill_polling register function.
bcma: fix build error on MIPS; implicit pcibios_enable_device
netfilter: nf_conntrack: fix incorrect logic in nf_conntrack_init_net
netfilter: nf_ct_ipv4: packets with wrong ihl are invalid
netfilter: nf_ct_ipv4: handle invalid IPv4 and IPv6 packets consistently
net/wireless/wext-core.c: add missing kfree
rtlwifi: Fix oops on rate-control failure
mac80211: Convert WARN_ON to WARN_ON_ONCE
rtlwifi: rtl8192de: Fix firmware initialization
nl80211: ensure interface is up in various APIs
...
1/ regression fix for Xen as it now trips over a broken assumption
about the dma address size on 32-bit builds
2/ new quirk for netdma to ignore dma channels that cannot meet
netdma alignment requirements
3/ fixes for two long standing issues in ioatdma (ring size overflow)
and iop-adma (potential stack corruption)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=F3IR
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/dmaengine
Pull dmaengine fixes from Dan Williams:
1/ regression fix for Xen as it now trips over a broken assumption
about the dma address size on 32-bit builds
2/ new quirk for netdma to ignore dma channels that cannot meet
netdma alignment requirements
3/ fixes for two long standing issues in ioatdma (ring size overflow)
and iop-adma (potential stack corruption)
* tag 'dmaengine-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/dmaengine:
netdma: adding alignment check for NETDMA ops
ioatdma: DMA copy alignment needed to address IOAT DMA silicon errata
ioat: ring size variables need to be 32bit to avoid overflow
iop-adma: Corrected array overflow in RAID6 Xscale(R) test.
ioat: fix size of 'completion' for Xen
Fix a code path in tcp_rcv_rtt_update() that was comparing scaled and
unscaled RTT samples.
The intent in the code was to only use the 'm' measurement if it was a
new minimum. However, since 'm' had not yet been shifted left 3 bits
but 'new_sample' had, this comparison would nearly always succeed,
leading us to erroneously set our receive-side RTT estimate to the 'm'
sample when that sample could be nearly 8x too high to use.
The overall effect is to often cause the receive-side RTT estimate to
be significantly too large (up to 40% too large for brief periods in
my tests).
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the fallout from adding memcpy alignment workaround for certain
IOATDMA hardware. NetDMA will only use DMA engine that can handle byte align
ops.
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
With increasing receive window sizes, but speed of light not improved
that much, out of order queue can contain a huge number of skbs, waiting
to be moved to receive_queue when missing packets can fill the holes.
Some devices happen to use fat skbs (truesize of 4096 + sizeof(struct
sk_buff)) to store regular (MTU <= 1500) frames. This makes highly
probable sk_rmem_alloc hits sk_rcvbuf limit, which can be 4Mbytes in
many cases.
When limit is hit, tcp stack calls tcp_collapse_ofo_queue(), a true
latency killer and cpu cache blower.
Doing the coalescing attempt each time we add a frame in ofo queue
permits to keep memory use tight and in many cases avoid the
tcp_collapse() thing later.
Tested on various wireless setups (b43, ath9k, ...) known to use big skb
truesize, this patch removed the "packets collapsed in receive queue due
to low socket buffer" I had before.
This also reduced average memory used by tcp sockets.
With help from Neal Cardwell.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: H.K. Jerry Chu <hkchu@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split tcp_data_queue() in two parts for better readability.
tcp_data_queue_ofo() is responsible for queueing incoming skb into out
of order queue.
Change code layout so that the skb_set_owner_r() is performed only if
skb is not dropped.
This is a preliminary patch before "reduce out_of_order memory use"
following patch.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: H.K. Jerry Chu <hkchu@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add #define pr_fmt(fmt) as appropriate.
Add "IPv4: ", "TCP: ", and "IPsec: " to appropriate files.
Standardize on "UDPLite: " for appropriate uses.
Some prefixes were previously "UDPLITE: " and "UDP-Lite: ".
Add KBUILD_MODNAME ": " to icmp and gre.
Remove embedded prefixes as appropriate.
Add missing "\n" to pr_info in gre.c.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a more current kernel messaging style.
Convert a printk block to print_hex_dump.
Coalesce formats, align arguments.
Use %s, __func__ instead of embedding function names.
Some messages that were prefixed with <foo>_close are
now prefixed with <foo>_fini. Some ah4 and esp messages
are now not prefixed with "ip ".
The intent of this patch is to later add something like
#define pr_fmt(fmt) "IPv4: " fmt.
to standardize the output messages.
Text size is trivially reduced. (x86-32 allyesconfig)
$ size net/ipv4/built-in.o*
text data bss dec hex filename
887888 31558 249696 1169142 11d6f6 net/ipv4/built-in.o.new
887934 31558 249800 1169292 11d78c net/ipv4/built-in.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit fixes tcp_shift_skb_data() so that it does not shift
SACKed data below snd_una.
This fixes an issue whose symptoms exactly match reports showing
tp->sacked_out going negative since 3.3.0-rc4 (see "WARNING: at
net/ipv4/tcp_input.c:3418" thread on netdev).
Since 2008 (832d11c5cd)
tcp_shift_skb_data() had been shifting SACKed ranges that were below
snd_una. It checked that the *end* of the skb it was about to shift
from was above snd_una, but did not check that the end of the actual
shifted range was above snd_una; this commit adds that check.
Shifting SACKed ranges below snd_una is problematic because for such
ranges tcp_sacktag_one() short-circuits: it does not declare anything
as SACKed and does not increase sacked_out.
Before the fixes in commits cc9a672ee5
and daef52bab1, shifting SACKed ranges
below snd_una happened to work because tcp_shifted_skb() was always
(incorrectly) passing in to tcp_sacktag_one() an skb whose end_seq
tcp_shift_skb_data() had already guaranteed was beyond snd_una. Hence
tcp_sacktag_one() never short-circuited and always increased
tp->sacked_out in this case.
After those two fixes, my testing has verified that shifting SACKed
ranges below snd_una could cause tp->sacked_out to go negative with
the following sequence of events:
(1) tcp_shift_skb_data() sees an skb whose end_seq is beyond snd_una,
then shifts a prefix of that skb that is below snd_una
(2) tcp_shifted_skb() increments the packet count of the
already-SACKed prev sk_buff
(3) tcp_sacktag_one() sees the end of the new SACKed range is below
snd_una, so it short-circuits and doesn't increase tp->sacked_out
(5) tcp_clean_rtx_queue() sees the SACKed skb has been ACKed,
decrements tp->sacked_out by this "inflated" pcount that was
missing a matching increase in tp->sacked_out, and hence
tp->sacked_out underflows to a u32 like 0xFFFFFFFF, which casted
to s32 is negative.
(6) this leads to the warnings seen in the recent "WARNING: at
net/ipv4/tcp_input.c:3418" thread on the netdev list; e.g.:
tcp_input.c:3418 WARN_ON((int)tp->sacked_out < 0);
More generally, I think this bug can be tickled in some cases where
two or more ACKs from the receiver are lost and then a DSACK arrives
that is immediately above an existing SACKed skb in the write queue.
This fix changes tcp_shift_skb_data() to abort this sequence at step
(1) in the scenario above by noticing that the bytes are below snd_una
and not shifting them.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In tcp_mark_head_lost() we should not attempt to fragment a SACKed skb
to mark the first portion as lost. This is for two primary reasons:
(1) tcp_shifted_skb() coalesces adjacent regions of SACKed skbs. When
doing this, it preserves the sum of their packet counts in order to
reflect the real-world dynamics on the wire. But given that skbs can
have remainders that do not align to MSS boundaries, this packet count
preservation means that for SACKed skbs there is not necessarily a
direct linear relationship between tcp_skb_pcount(skb) and
skb->len. Thus tcp_mark_head_lost()'s previous attempts to fragment
off and mark as lost a prefix of length (packets - oldcnt)*mss from
SACKed skbs were leading to occasional failures of the WARN_ON(len >
skb->len) in tcp_fragment() (which used to be a BUG_ON(); see the
recent "crash in tcp_fragment" thread on netdev).
(2) there is no real point in fragmenting off part of a SACKed skb and
calling tcp_skb_mark_lost() on it, since tcp_skb_mark_lost() is a NOP
for SACKed skbs.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When tcp_shifted_skb() shifts bytes from the skb that is currently
pointed to by 'highest_sack' then the increment of
TCP_SKB_CB(skb)->seq implicitly advances tcp_highest_sack_seq(). This
implicit advancement, combined with the recent fix to pass the correct
SACKed range into tcp_sacktag_one(), caused tcp_sacktag_one() to think
that the newly SACKed range was before the tcp_highest_sack_seq(),
leading to a call to tcp_update_reordering() with a degree of
reordering matching the size of the newly SACKed range (typically just
1 packet, which is a NOP, but potentially larger).
This commit fixes this by simply calling tcp_sacktag_one() before the
TCP_SKB_CB(skb)->seq advancement that can advance our notion of the
highest SACKed sequence.
Correspondingly, we can simplify the code a little now that
tcp_shifted_skb() should update the lost_cnt_hint in all cases where
skb == tp->lost_skb_hint.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit ensures that lost_cnt_hint is correctly updated in
tcp_shifted_skb() for FACK TCP senders. The lost_cnt_hint adjustment
in tcp_sacktag_one() only applies to non-FACK senders, so FACK senders
need their own adjustment.
This applies the spirit of 1e5289e121 -
except now that the sequence range passed into tcp_sacktag_one() is
correct we need only have a special case adjustment for FACK.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the newly-SACKed range to be the range of newly-shifted bytes.
Previously - since 832d11c5cd -
tcp_shifted_skb() incorrectly called tcp_sacktag_one() with the start
and end sequence numbers of the skb it passes in set to the range just
beyond the range that is newly-SACKed.
This commit also removes a special-case adjustment to lost_cnt_hint in
tcp_shifted_skb() since the pre-existing adjustment of lost_cnt_hint
in tcp_sacktag_one() now properly handles this things now that the
correct start sequence number is passed in.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit allows callers of tcp_sacktag_one() to pass in sequence
ranges that do not align with skb boundaries, as tcp_shifted_skb()
needs to do in an upcoming fix in this patch series.
In fact, now tcp_sacktag_one() does not need to depend on an input skb
at all, which makes its semantics and dependencies more clear.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correctly implement a loss detection heuristic: New sequences (above
high_seq) sent during the fast recovery are deemed lost when higher
sequences are SACKed.
Current code does not catch these losses, because tcp_mark_head_lost()
does not check packets beyond high_seq. The fix is straight-forward by
checking packets until the highest sacked packet. In addition, all the
FLAG_DATA_LOST logic are in-effective and redundant and can be removed.
Update the loss heuristic comments. The algorithm above is documented
as heuristic B, but it is redundant too because heuristic A already
covers B.
Note that this change only marks some forward-retransmitted packets LOST.
It does NOT forbid TCP performing further CWR on new losses. A potential
follow-up patch under preparation is to perform another CWR on "new"
losses such as
1) sequence above high_seq is lost (by resetting high_seq to snd_nxt)
2) retransmission is lost.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
to record the state of SACK/FACK and DSACK for better readability and maintenance.
Signed-off-by: Vijay Subramanian <subramanian.vijay@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces all uses of struct sock fields' memory_pressure,
memory_allocated, sockets_allocated, and sysctl_mem to acessor
macros. Those macros can either receive a socket argument, or a mem_cgroup
argument, depending on the context they live in.
Since we're only doing a macro wrapping here, no performance impact at all is
expected in the case where we don't have cgroups disabled.
Signed-off-by: Glauber Costa <glommer@parallels.com>
Reviewed-by: Hiroyouki Kamezawa <kamezawa.hiroyu@jp.fujitsu.com>
CC: David S. Miller <davem@davemloft.net>
CC: Eric W. Biederman <ebiederm@xmission.com>
CC: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of testing defined(CONFIG_IPV6) || defined(CONFIG_IPV6_MODULE)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Denys Fedoryshchenko reported that SYN+FIN attacks were bringing his
linux machines to their limits.
Dont call conn_request() if the TCP flags includes SYN flag
Reported-by: Denys Fedoryshchenko <denys@visp.net.lb>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The problem: Senders were overriding cwnd values picked during an undo
by calling tcp_moderate_cwnd() in tcp_try_to_open().
The fix: Don't moderate cwnd in tcp_try_to_open() if we're in
TCP_CA_Open, since doing so is generally unnecessary and specifically
would override a DSACK-based undo of a cwnd reduction made in fast
recovery.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, SACK-enabled connections hung around in TCP_CA_Disorder
state while snd_una==high_seq, just waiting to accumulate DSACKs and
hopefully undo a cwnd reduction. This could and did lead to the
following unfortunate scenario: if some incoming ACKs advance snd_una
beyond high_seq then we were setting undo_marker to 0 and moving to
TCP_CA_Open, so if (due to reordering in the ACK return path) we
shortly thereafter received a DSACK then we were no longer able to
undo the cwnd reduction.
The change: Simplify the congestion avoidance state machine by
removing the behavior where SACK-enabled connections hung around in
the TCP_CA_Disorder state just waiting for DSACKs. Instead, when
snd_una advances to high_seq or beyond we typically move to
TCP_CA_Open immediately and allow an undo in either TCP_CA_Open or
TCP_CA_Disorder if we later receive enough DSACKs.
Other patches in this series will provide other changes that are
necessary to fully fix this problem.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bug: When the ACK field is below snd_una (which can happen when
ACKs are reordered), senders ignored DSACKs (preventing undo) and did
not call tcp_fastretrans_alert, so they did not increment
prr_delivered to reflect newly-SACKed sequence ranges, and did not
call tcp_xmit_retransmit_queue, thus passing up chances to send out
more retransmitted and new packets based on any newly-SACKed packets.
The change: When the ACK field is below snd_una (the "old_ack" goto
label), call tcp_fastretrans_alert to allow undo based on any
newly-arrived DSACKs and try to send out more packets based on
newly-SACKed packets.
Other patches in this series will provide other changes that are
necessary to fully fix this problem.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bug: Senders ignored DSACKs after recovery when there were no
outstanding packets (a common scenario for HTTP servers).
The change: when there are no outstanding packets (the "no_queue" goto
label), call tcp_fastretrans_alert() in order to use DSACKs to undo
congestion window reductions.
Other patches in this series will provide other changes that are
necessary to fully fix this problem.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow callers to decide whether an ACK is a duplicate ACK. This is a
prerequisite to allowing fastretrans_alert to be called from new
contexts, such as the no_queue and old_ack code paths, from which we
have extra info that tells us whether an ACK is a dupack.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding const qualifiers to pointers can ease code review, and spot some
bugs. It might allow compiler to optimize code further.
For example, is it legal to temporary write a null cksum into tcphdr
in tcp_md5_hash_header() ? I am afraid a sniffer could catch the
temporary null value...
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_fin() only needs socket pointer, we can remove skb and th params.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 356f039822 (TCP: increase default initial receive
window.), we allow sender to send 10 (TCP_DEFAULT_INIT_RCVWND) segments.
Change tcp_fixup_rcvbuf() to reflect this change, even if no real change
is expected, since sysctl_tcp_rmem[1] = 87380 and this value
is bigger than tcp_fixup_rcvbuf() computed rcvmem (~23720)
Note: Since commit 356f039822 limited default window to maximum of
10*1460 and 2*MSS, we use same heuristic in this patch.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initial cwnd being 10 (TCP_INIT_CWND) instead of 3, change
tcp_fixup_sndbuf() to get more than 16384 bytes (sysctl_tcp_wmem[1]) in
initial sk_sndbuf
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb truesize currently accounts for sk_buff struct and part of skb head.
kmalloc() roundings are also ignored.
Considering that skb_shared_info is larger than sk_buff, its time to
take it into account for better memory accounting.
This patch introduces SKB_TRUESIZE(X) macro to centralize various
assumptions into a single place.
At skb alloc phase, we put skb_shared_info struct at the exact end of
skb head, to allow a better use of memory (lowering number of
reallocations), since kmalloc() gives us power-of-two memory blocks.
Unless SLUB/SLUB debug is active, both skb->head and skb_shared_info are
aligned to cache lines, as before.
Note: This patch might trigger performance regressions because of
misconfigured protocol stacks, hitting per socket or global memory
limits that were previously not reached. But its a necessary step for a
more accurate memory accounting.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Andi Kleen <ak@linux.intel.com>
CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
lost_skb_hint is used by tcp_mark_head_lost() to mark the first unhandled skb.
lost_cnt_hint is the number of packets or sacked packets before the lost_skb_hint;
When shifting a skb that is before the lost_skb_hint, if tcp_is_fack() is ture,
the skb has already been counted in the lost_cnt_hint; if tcp_is_fack() is false,
tcp_sacktag_one() will increase the lost_cnt_hint. So tcp_shifted_skb() does not
need to adjust the lost_cnt_hint by itself. When shifting a skb that is equal to
lost_skb_hint, the shifted packets will not be counted by tcp_mark_head_lost().
So tcp_shifted_skb() should adjust the lost_cnt_hint even tcp_is_fack(tp) is true.
Signed-off-by: Zheng Yan <zheng.z.yan@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename struct tcp_skb_cb "flags" to "tcp_flags" to ease code review and
maintenance.
Its content is a combination of FIN/SYN/RST/PSH/ACK/URG/ECE/CWR flags
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct tcp_skb_cb contains a "flags" field containing either tcp flags
or IP dsfield depending on context (input or output path)
Introduce ip_dsfield to make the difference clear and ease maintenance.
If later we want to save space, we can union flags/ip_dsfield
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While playing with a new ADSL box at home, I discovered that ECN
blackhole can trigger suboptimal quickack mode on linux : We send one
ACK for each incoming data frame, without any delay and eventual
piggyback.
This is because TCP_ECN_check_ce() considers that if no ECT is seen on a
segment, this is because this segment was a retransmit.
Refine this heuristic and apply it only if we seen ECT in a previous
segment, to detect ECN blackhole at IP level.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Jamal Hadi Salim <jhs@mojatatu.com>
CC: Jerry Chu <hkchu@google.com>
CC: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
CC: Jim Gettys <jg@freedesktop.org>
CC: Dave Taht <dave.taht@gmail.com>
Acked-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
D-SACK is allowed to reside below snd_una. But the corresponding check
in tcp_is_sackblock_valid() is the exact opposite. It looks like a typo.
Signed-off-by: Zheng Yan <zheng.z.yan@intel.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements Proportional Rate Reduction (PRR) for TCP.
PRR is an algorithm that determines TCP's sending rate in fast
recovery. PRR avoids excessive window reductions and aims for
the actual congestion window size at the end of recovery to be as
close as possible to the window determined by the congestion control
algorithm. PRR also improves accuracy of the amount of data sent
during loss recovery.
The patch implements the recommended flavor of PRR called PRR-SSRB
(Proportional rate reduction with slow start reduction bound) and
replaces the existing rate halving algorithm. PRR improves upon the
existing Linux fast recovery under a number of conditions including:
1) burst losses where the losses implicitly reduce the amount of
outstanding data (pipe) below the ssthresh value selected by the
congestion control algorithm and,
2) losses near the end of short flows where application runs out of
data to send.
As an example, with the existing rate halving implementation a single
loss event can cause a connection carrying short Web transactions to
go into the slow start mode after the recovery. This is because during
recovery Linux pulls the congestion window down to packets_in_flight+1
on every ACK. A short Web response often runs out of new data to send
and its pipe reduces to zero by the end of recovery when all its packets
are drained from the network. Subsequent HTTP responses using the same
connection will have to slow start to raise cwnd to ssthresh. PRR on
the other hand aims for the cwnd to be as close as possible to ssthresh
by the end of recovery.
A description of PRR and a discussion of its performance can be found at
the following links:
- IETF Draft:
http://tools.ietf.org/html/draft-mathis-tcpm-proportional-rate-reduction-01
- IETF Slides:
http://www.ietf.org/proceedings/80/slides/tcpm-6.pdfhttp://tools.ietf.org/agenda/81/slides/tcpm-2.pdf
- Paper to appear in Internet Measurements Conference (IMC) 2011:
Improving TCP Loss Recovery
Nandita Dukkipati, Matt Mathis, Yuchung Cheng
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch lowers the default initRTO from 3secs to 1sec per
RFC2988bis. It falls back to 3secs if the SYN or SYN-ACK packet
has been retransmitted, AND the TCP timestamp option is not on.
It also adds support to take RTT sample during 3WHS on the passive
open side, just like its active open counterpart, and uses it, if
valid, to seed the initRTO for the data transmission phase.
The patch also resets ssthresh to its initial default at the
beginning of the data transmission phase, and reduces cwnd to 1 if
there has been MORE THAN ONE retransmission during 3WHS per RFC5681.
Signed-off-by: H.K. Jerry Chu <hkchu@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current undo logic, cwnd is moderated after it was restored
to the value prior entering fast-recovery. It was moderated first
in tcp_try_undo_recovery then again in tcp_complete_cwr.
Since the undo indicates recovery was false, these moderations
are not necessary. If the undo is triggered when most of the
outstanding data have been acknowledged, the (restored) cwnd is
falsely pulled down to a small value.
This patch removes these cwnd moderations if cwnd is undone
a) during fast-recovery
b) by receiving DSACKs past fast-recovery
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the congestion control interface, the callback for each ACK
includes an estimated round trip time in microseconds.
Some algorithms need high resolution (Vegas style) but most only
need jiffie resolution. If RTT is not accurate (like a retransmission)
-1 is used as a flag value.
When doing coarse resolution if RTT is less than a a jiffie
then 0 should be returned rather than no estimate. Otherwise algorithms
that expect good ack's to trigger slow start (like CUBIC Hystart)
will be confused.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a bug that undo_retrans is incorrectly decremented when undo_marker is
not set or undo_retrans is already 0. This happens when sender receives
more DSACK ACKs than packets retransmitted during the current
undo phase. This may also happen when sender receives DSACK after
the undo operation is completed or cancelled.
Fix another bug that undo_retrans is incorrectly incremented when
sender retransmits an skb and tcp_skb_pcount(skb) > 1 (TSO). This case
is rare but not impossible.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a bug that causes TCP RST packets to be generated
on otherwise correctly behaved applications, e.g., no unread data
on close,..., etc. To trigger the bug, at least two conditions must
be met:
1. The FIN flag is set on the last data packet, i.e., it's not on a
separate, FIN only packet.
2. The size of the last data chunk on the receive side matches
exactly with the size of buffer posted by the receiver, and the
receiver closes the socket without any further read attempt.
This bug was first noticed on our netperf based testbed for our IW10
proposal to IETF where a large number of RST packets were observed.
netperf's read side code meets the condition 2 above 100%.
Before the fix, tcp_data_queue() will queue the last skb that meets
condition 1 to sk_receive_queue even though it has fully copied out
(skb_copy_datagram_iovec()) the data. Then if condition 2 is also met,
tcp_recvmsg() often returns all the copied out data successfully
without actually consuming the skb, due to a check
"if ((chunk = len - tp->ucopy.len) != 0) {"
and
"len -= chunk;"
after tcp_prequeue_process() that causes "len" to become 0 and an
early exit from the big while loop.
I don't see any reason not to free the skb whose data have been fully
consumed in tcp_data_queue(), regardless of the FIN flag. We won't
get there if MSG_PEEK is on. Am I missing some arcane cases related
to urgent data?
Signed-off-by: H.K. Jerry Chu <hkchu@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 86bcebafc5 ("tcp: fix >2 iw selection") fixed a case
when congestion window initialization has been mistakenly omitted
by introducing cwnd label and putting backwards goto from the
end of the function.
This makes the code unnecessarily tricky to read and understand
on a first sight.
Shuffle the code around a little bit to make it more obvious.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use helper functions to hide all direct accesses, especially writes,
to dst_entry metrics values.
This will allow us to:
1) More easily change how the metrics are stored.
2) Implement COW for metrics.
In particular this will help us put metrics into the inetpeer
cache if that is what we end up doing. We can make the _metrics
member a pointer instead of an array, initially have it point
at the read-only metrics in the FIB, and then on the first set
grab an inetpeer entry and point the _metrics member there.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Robin Holt tried to boot a 16TB machine and found some limits were
reached : sysctl_tcp_mem[2], sysctl_udp_mem[2]
We can switch infrastructure to use long "instead" of "int", now
atomic_long_t primitives are available for free.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Reported-by: Robin Holt <holt@sgi.com>
Reviewed-by: Robin Holt <holt@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch below updates broken web addresses in the kernel
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Dimitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Mike Frysinger <vapier.adi@gmail.com>
Acked-by: Ben Pfaff <blp@cs.stanford.edu>
Acked-by: Hans J. Koch <hjk@linutronix.de>
Reviewed-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When only fast rexmit should be done, tcp_mark_head_lost marks
L too far. Also, sacked_upto below 1 is perfectly valid number,
the packets == 0 then needs to be trapped elsewhere.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
This looks like a simple typo that has gone unnoticed for some time. The
impact is relatively low but it's clearly wrong.
Signed-off-by: John Heffner <johnwheffner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When TCP uses FACK algorithm to mark lost packets in
tcp_mark_head_lost(), if the number of packets in the (TSO) skb is
greater than the number of packets that should be marked lost, TCP
incorrectly exits the loop and marks no packets lost in the skb. This
underestimates tp->lost_out and affects the recovery/retransmission.
This patch fargments the skb and marks the correct amount of packets
lost.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change "return (EXPR);" to "return EXPR;"
return is not a function, parentheses are not required.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a RST comes in immediately after checking sk->sk_err, tcp_poll will
return POLLIN but not POLLOUT. Fix this by checking sk->sk_err at the end
of tcp_poll. Additionally, ensure the correct order of operations on SMP
machines with memory barriers.
Signed-off-by: Tom Marshall <tdm.code@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch consolidates initial-window code common to TCP and CCID-2:
* TCP uses RFC 3390 in a packet-oriented manner (tcp_input.c) and
* CCID-2 uses RFC 3390 in packet-oriented manner (RFC 4341).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_parse_md5sig_option doesn't check md5sig option (TCPOPT_MD5SIG)
length, but tcp_v[46]_inbound_md5_hash assume that it's at least 16
bytes long.
Signed-off-by: Dmitry Popov <dp@highloadlab.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CodingStyle cleanups
EXPORT_SYMBOL should immediately follow the symbol declaration.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit: c720c7e838 missed these.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also added an explicit break; to avoid
a fallthrough in net/ipv4/tcp_input.c
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When queueing a skb to socket, we can immediately release its dst if
target socket do not use IP_CMSG_PKTINFO.
tcp_data_queue() can drop dst too.
This to benefit from a hot cache line and avoid the receiver, possibly
on another cpu, to dirty this cache line himself.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With latest CONFIG_PROVE_RCU stuff, I felt more comfortable to make this
work.
sk->sk_dst_cache is currently protected by a rwlock (sk_dst_lock)
This rwlock is readlocked for a very small amount of time, and dst
entries are already freed after RCU grace period. This calls for RCU
again :)
This patch converts sk_dst_lock to a spinlock, and use RCU for readers.
__sk_dst_get() is supposed to be called with rcu_read_lock() or if
socket locked by user, so use appropriate rcu_dereference_check()
condition (rcu_read_lock_held() || sock_owned_by_user(sk))
This patch avoids two atomic ops per tx packet on UDP connected sockets,
for example, and permits sk_dst_lock to be much less dirtied.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
A packet is marked as lost in case packets == 0, although nothing should be done.
This results in a too early retransmitted packet during recovery in some cases.
This small patch fixes this issue by returning immediately.
Signed-off-by: Lennart Schulte <lennart.schulte@nets.rwth-aachen.de>
Signed-off-by: Arnd Hannemann <hannemann@nets.rwth-aachen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables fast retransmissions after one dupACK for
TCP if the stream is identified as thin. This will reduce
latencies for thin streams that are not able to trigger fast
retransmissions due to high packet interarrival time. This
mechanism is only active if enabled by iocontrol or syscontrol
and the stream is identified as thin.
Signed-off-by: Andreas Petlund <apetlund@simula.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure, that TCP has a nonzero RTT estimation after three-way
handshake. Currently, a listening TCP has a value of 0 for srtt,
rttvar and rto right after the three-way handshake is completed
with TCP timestamps disabled.
This will lead to corrupt RTO recalculation and retransmission
flood when RTO is recalculated on backoff reversion as introduced
in "Revert RTO on ICMP destination unreachable"
(f1ecd5d9e7).
This behaviour can be provoked by connecting to a server which
"responds first" (like SMTP) and rejecting every packet after
the handshake with dest-unreachable, which will lead to softirq
load on the server (up to 30% per socket in some tests).
Thanks to Ilpo Jarvinen for providing debug patches and to
Denys Fedoryshchenko for reporting and testing.
Changes since v3: Removed bad characters in patchfile.
Reported-by: Denys Fedoryshchenko <denys@visp.net.lb>
Signed-off-by: Damian Lukowski <damian@tvk.rwth-aachen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
It creates a regression, triggering badness for SYN_RECV
sockets, for example:
[19148.022102] Badness at net/ipv4/inet_connection_sock.c:293
[19148.022570] NIP: c02a0914 LR: c02a0904 CTR: 00000000
[19148.023035] REGS: eeecbd30 TRAP: 0700 Not tainted (2.6.32)
[19148.023496] MSR: 00029032 <EE,ME,CE,IR,DR> CR: 24002442 XER: 00000000
[19148.024012] TASK = eee9a820[1756] 'privoxy' THREAD: eeeca000
This is likely caused by the change in the 'estab' parameter
passed to tcp_parse_options() when invoked by the functions
in net/ipv4/tcp_minisocks.c
But even if that is fixed, the ->conn_request() changes made in
this patch series is fundamentally wrong. They try to use the
listening socket's 'dst' to probe the route settings. The
listening socket doesn't even have a route, and you can't
get the right route (the child request one) until much later
after we setup all of the state, and it must be done by hand.
This stuff really isn't ready, so the best thing to do is a
full revert. This reverts the following commits:
f55017a93f022c3f7d821aba721ebacda42ebd67345cda2fd6dc343475ed05eaade2786a2a2d6bf8
Signed-off-by: David S. Miller <davem@davemloft.net>
It can happen, that tcp_retransmit_skb fails due to some error.
In such cases we might end up into a state where tp->retrans_out
is zero but that's only because we removed the TCPCB_SACKED_RETRANS
bit from a segment but couldn't retransmit it because of the error
that happened. Therefore some assumptions that retrans_out checks
are based do not necessarily hold, as there still can be an old
retransmission but that is only visible in TCPCB_EVER_RETRANS bit.
As retransmission happen in sequential order (except for some very
rare corner cases), it's enough to check the head skb for that bit.
Main reason for all this complexity is the fact that connection dying
time now depends on the validity of the retrans_stamp, in particular,
that successive retransmissions of a segment must not advance
retrans_stamp under any conditions. It seems after quick thinking that
this has relatively low impact as eventually TCP will go into CA_Loss
and either use the existing check for !retrans_stamp case or send a
retransmission successfully, setting a new base time for the dying
timer (can happen only once). At worst, the dying time will be
approximately the double of the intented time. In addition,
tcp_packet_delayed() will return wrong result (has some cc aspects
but due to rarity of these errors, it's hardly an issue).
One of retrans_stamp clearing happens indirectly through first going
into CA_Open state and then a later ACK lets the clearing to happen.
Thus tcp_try_keep_open has to be modified too.
Thanks to Damian Lukowski <damian@tvk.rwth-aachen.de> for hinting
that this possibility exists (though the particular case discussed
didn't after all have it happening but was just a debug patch
artifact).
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Parse incoming TCP_COOKIE option(s).
Calculate <SYN,ACK> TCP_COOKIE option.
Send optional <SYN,ACK> data.
This is a significantly revised implementation of an earlier (year-old)
patch that no longer applies cleanly, with permission of the original
author (Adam Langley):
http://thread.gmane.org/gmane.linux.network/102586
Requires:
TCPCT part 1a: add request_values parameter for sending SYNACK
TCPCT part 1b: generate Responder Cookie secret
TCPCT part 1c: sysctl_tcp_cookie_size, socket option TCP_COOKIE_TRANSACTIONS
TCPCT part 1d: define TCP cookie option, extend existing struct's
TCPCT part 1e: implement socket option TCP_COOKIE_TRANSACTIONS
TCPCT part 1f: Initiator Cookie => Responder
Signed-off-by: William.Allen.Simpson@gmail.com
Signed-off-by: David S. Miller <davem@davemloft.net>
On Sun, 2009-11-22 at 16:31 -0800, David Miller wrote:
> It should be of the form:
> if (x &&
> y)
>
> or:
> if (x && y)
>
> Fix patches, rather than complaints, for existing cases where things
> do not follow this pattern are certainly welcome.
Also collapsed some multiple tabs to single space.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define two symbols needed in both kernel and user space.
Remove old (somewhat incorrect) kernel variant that wasn't used in
most cases. Default should apply to both RMSS and SMSS (RFC2581).
Replace numeric constants with defined symbols.
Stand-alone patch, originally developed for TCPCT.
Signed-off-by: William.Allen.Simpson@gmail.com
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trying to parse the option of a SYN packet that we have
no route entry for should just use global wide defaults
for route entry options.
Signed-off-by: Gilad Ben-Yossef <gilad@codefidence.com>
Tested-by: Valdis.Kletnieks@vt.edu
Signed-off-by: David S. Miller <davem@davemloft.net>
Add and use no DSCAK bit in the features field.
Signed-off-by: Gilad Ben-Yossef <gilad@codefidence.com>
Sigend-off-by: Ori Finkelman <ori@comsleep.com>
Sigend-off-by: Yony Amit <yony@comsleep.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add and use no window scale bit in the features field.
Note that this is not the same as setting a window scale of 0
as would happen with window limit on route.
Signed-off-by: Gilad Ben-Yossef <gilad@codefidence.com>
Sigend-off-by: Ori Finkelman <ori@comsleep.com>
Sigend-off-by: Yony Amit <yony@comsleep.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement querying and acting upon the no timestamp bit in the feature
field.
Signed-off-by: Gilad Ben-Yossef <gilad@codefidence.com>
Sigend-off-by: Ori Finkelman <ori@comsleep.com>
Sigend-off-by: Yony Amit <yony@comsleep.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement querying and acting upon the no sack bit in the features
field.
Signed-off-by: Gilad Ben-Yossef <gilad@codefidence.com>
Sigend-off-by: Ori Finkelman <ori@comsleep.com>
Sigend-off-by: Yony Amit <yony@comsleep.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need tcp_parse_options to be aware of dst_entry to
take into account per dst_entry TCP options settings
Signed-off-by: Gilad Ben-Yossef <gilad@codefidence.com>
Sigend-off-by: Ori Finkelman <ori@comsleep.com>
Sigend-off-by: Yony Amit <yony@comsleep.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Corrected a spelling error in a function name.
Signed-off-by: Andreas Petlund <apetlund@simula.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was once upon time so that snd_sthresh was a 16-bit quantity.
...That has not been true for long period of time. I run across
some ancient compares which still seem to trust such legacy.
Put all that magic into a single place, I hopefully found all
of them.
Compile tested, though linking of allyesconfig is ridiculous
nowadays it seems.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here, an ICMP host/network unreachable message, whose payload fits to
TCP's SND.UNA, is taken as an indication that the RTO retransmission has
not been lost due to congestion, but because of a route failure
somewhere along the path.
With true congestion, a router won't trigger such a message and the
patched TCP will operate as standard TCP.
This patch reverts one RTO backoff, if an ICMP host/network unreachable
message, whose payload fits to TCP's SND.UNA, arrives.
Based on the new RTO, the retransmission timer is reset to reflect the
remaining time, or - if the revert clocked out the timer - a retransmission
is sent out immediately.
Backoffs are only reverted, if TCP is in RTO loss recovery, i.e. if
there have been retransmissions and reversible backoffs, already.
Changes from v2:
1) Renaming of skb in tcp_v4_err() moved to another patch.
2) Reintroduced tcp_bound_rto() and __tcp_set_rto().
3) Fixed code comments.
Signed-off-by: Damian Lukowski <damian@tvk.rwth-aachen.de>
Acked-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Somewhat luckily, I was looking into these parts with very fine
comb because I've made somewhat similar changes on the same
area (conflicts that arose weren't that lucky though). The loop
was very much overengineered recently in commit 915219441d
(tcp: Use SKB queue and list helpers instead of doing it
by-hand), while it basically just wants to know if there are
skbs after 'skb'.
Also it got broken because skb1 = skb->next got translated into
skb1 = skb1->next (though abstracted) improperly. Note that
'skb1' is pointing to previous sk_buff than skb or NULL if at
head. Two things went wrong:
- We'll kfree 'skb' on the first iteration instead of the
skbuff following 'skb' (it would require required SACK reneging
to recover I think).
- The list head case where 'skb1' is NULL is checked too early
and the loop won't execute whereas it previously did.
Conclusion, mostly revert the recent changes which makes the
cset very messy looking but using proper accessor in the
previous-like version.
The effective changes against the original can be viewed with:
git-diff 915219441d566f1da0caa0e262be49b666159e17^ \
net/ipv4/tcp_input.c | sed -n -e '57,70 p'
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_prequeue() refers to the constant value (TCP_RTO_MIN) regardless of
the actual value might be tuned. The following patches fix this and make
tcp_prequeue get the actual value returns from tcp_rto_min().
Signed-off-by: Satoru SATOH <satoru.satoh@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This should be very safe compared with full enabled, so I see
no reason why it shouldn't be done right away. As ECN can only
be negotiated if the SYN sending party is also supporting it,
somebody in the loop probably knows what he/she is doing. If
SYN does not ask for ECN, the server side SYN-ACK is identical
to what it is without ECN. Thus it's quite safe.
The chosen value is safe w.r.t to existing configs which
choose to currently set manually either 0 or 1 but
silently upgrades those who have not explicitly requested
ECN off.
Whether to just enable both sides comes up time to time but
unless that gets done now we can at least make the servers
aware of ECN already. As there are some known problems to occur
if ECN is enabled, it's currently questionable whether there's
any real gain from enabling clients as servers mostly won't
support it anyway (so we'd hit just the negative sides). After
enabling the servers and getting that deployed, the client end
enable really has some potential gain too.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
A long-standing feature in tcp_init_metrics() is such that
any of its goto reset prevents call to tcp_init_cwnd().
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Discard incoming packets whose ack field iincludes data not yet sent.
This is consistent with RFC 793 Section 3.9.
Change tcp_ack() to distinguish between too-small and too-large ack
field values. Keep segments with too-large ack fields out of the fast
path, and change slow path to discard them.
Reported-by: Oliver Zheng <mailinglists+netdev@oliverzheng.com>
Signed-off-by: John Dykstra <john.dykstra1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_sack_swap seems unnecessary so I pushed swap to the caller.
Also removed comment that seemed then pointless, and added include
when not already there. Compile tested.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's very little need for most of the callsites to get
tp->xmit_goal_size updated. That will cost us divide as is,
so slice the function in two. Also, the only users of the
tp->xmit_goal_size are directly behind tcp_current_mss(),
so there's no need to store that variable into tcp_sock
at all! The drop of xmit_goal_size currently leaves 16-bit
hole and some reorganization would again be necessary to
change that (but I'm aiming to fill that hole with u16
xmit_goal_size_segs to cache the results of the remaining
divide to get that tso on regression).
Bring xmit_goal_size parts into tcp.c
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems that no variables clash such that we couldn't do
the check just once later on. Therefore move it.
Also kill dead obvious comment, dead argument and add
unlikely since this mtu probe does not happen too often.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet