This maps out all of the function types to pinctrl function groups.
Presently this is restricted to one pin per function to maintain
compatability with legacy behaviour. This will be extended as groups
are introduced and exiting users migrated.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This begins the migration of the PFC core to the pinctrl subsystem.
Initial support is very basic, with the bulk of the implementation simply
being nopped out in such a way to allow registration with the pinctrl
core to succeed.
The gpio chip driver is stripped down considerably now relying purely on
pinctrl API calls to manage the bulk of its operations.
This provides a basis for further PFC refactoring, including decoupling
pin functions from the GPIO API, establishing pin groups, and so forth.
These will all be dealt with incrementally so as to introduce as few
growing and migratory pains to tree-wide PFC pinmux users today.
When the interfaces have been well established and in-tree users have
been migrated off of the legacy interfaces it will be possible to strip
down the core considerably, leading to eventual drivers/pinctrl rehoming.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This follows the intc/clk changes and shuffles the PFC support code under
its own directory. This will facilitate better code sharing, and allow us
to trim down the exported interface by quite a margin.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The encoding is tightly packed, and future changes (such as
pinconf-generic support) can easily lead to a situation where we violate
the encoding constraints and trample data bit/reg bits. This plugs in
some sanity checks by way of a BUILD_BUG_ON() to blow up if we fail to
fit.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This implements some Kconfig knobs for ensuring that the PFC gpio chip
can be disabled or built as a module in the cases where it's optional, or
forcibly enabled in cases where it's not.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This implements a bit of rework for the PFC code, making the core itself
slightly more pluggable and moving out the gpio chip handling completely.
The API is preserved in such a way that platforms that depend on it for
early configuration are still able to do so, while making it possible to
migrate to alternate interfaces going forward.
This is the first step of chainsawing necessary to support the pinctrl
API, with the eventual goal being able to decouple pin function state
from the gpio API while retaining gpio chip tie-in for gpio pin functions
only, relying on the pinctrl/pinmux API for non-gpio function demux.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This switches to using irq_alloc_desc() directly for subgroup IRQs.
We still need to call activate_irq() on these in order to make them
requestable, at least up until these get moved in to their own irq
domain..
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This consolidates the div6/4 versions of the clk registration wrapper.
The existing wrappers with their own sh_clk_ops are maintained for API
compatability, though in the future it should be possible to be rid of
them entirely.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Everything with the exception of the _reparent ops are now shared, so
switch everything over to common types.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This introduces a new flag for clocks that need to have their divisor
ratio set back to their initial mask at disable time to prevent
interactivity problems with the clock stop bit (presently div6 only).
With this in place it's possible to handle the corner case on top of the
div4 op without any particular need for leaving things split out.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This plugs in a div_mask for the clock and sets it up for the existing
div6/4 cases. This will make it possible to support other div types, as
well as share more div6/4 infrastructure.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This plugs in a generic clk_div_table, based on the div4 version. div6 is
then adopted to use it for encapsulating its div table, which permits us
to start div6/4 unification, as well as preparation for other div types.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
At present reserving the IRLs in the IRQ bitmap in addition to the
dropping of the legacy IRQ pre-allocation prevent IRL IRQs from being
allocated for the x3proto board.
The only reason to permit reservations was to lock down possible hardware
vectors prior to dynamic IRQ scanning, but this doesn't matter much given
that the hardware controller configuration is sorted before we get around
to doing any dynamic IRQ allocation anyways. Beyond that, all of the
tables are __init annotated, so quite a bit more work would need to be
done to support reconfiguring things like IRL controllers on the fly,
much more than would ever make it worth the hassle.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This follows the MSTP clock change and implements variable access size
support for the rest of the CPG clocks, too. Upcoming SH-2A support has
need of this for 16-bit div4 clocks, while others will follow.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The bulk of the MSTP users require 32-bit access, but this isn't the case
for some of the SH-2A parts, so add in some basic infrastructure to let
the CPU define its required access size in preparation.
Requested-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.15 (GNU/Linux)
iEYEABECAAYFAk91TL0ACgkQGkmNcg7/o7hEjwCgmuz6QQKkow7e5q0x7DR5Z2NH
1YoAn3TpODDmpaBiou26uMRPhcR6e1qC
=JCA0
-----END PGP SIGNATURE-----
Merge tag 'sh-for-linus' of git://github.com/pmundt/linux-sh
Pull SuperH updates from Paul Mundt.
* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh: (25 commits)
sh: Support I/O space swapping where needed.
sh: use set_current_blocked() and block_sigmask()
sh: no need to reset handler if SA_ONESHOT
sh: intc: Fix up section mismatch for intc_ack_data
sh: select ARCH_DISCARD_MEMBLOCK.
sh: Consolidate duplicate _32/_64 unistd definitions.
sh: ecovec: switch SDHI controllers to card polling
sh: Avoid exporting unimplemented syscalls.
sh: add platform_device for RSPI in setup-sh7757
SH: pci-sh7780: enable big-endian operation.
serial: sh-sci: fix a race of DMA submit_tx on transfer
sh: dma: Collect up CHCR of SH7763, SH7764, SH7780 and SH7785
sh: dma: Collect up CHCR of SH7723 and SH7730
sh/next: Fix build fail by asm/system.h in asm/bitops.h
arch/sh/drivers/dma/{dma-g2,dmabrg}.c: ensure arguments to request_irq and free_irq are compatible
sh: cpufreq: Wire up scaling_available_freqs support.
sh: cpufreq: notify about rate rounding fallback.
sh: cpufreq: Support CPU clock frequency table.
sh: cpufreq: struct device lookup from CPU topology.
sh: cpufreq: percpu struct clk accounting.
...
Pull more ARM updates from Russell King.
This got a fair number of conflicts with the <asm/system.h> split, but
also with some other sparse-irq and header file include cleanups. They
all looked pretty trivial, though.
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm: (59 commits)
ARM: fix Kconfig warning for HAVE_BPF_JIT
ARM: 7361/1: provide XIP_VIRT_ADDR for no-MMU builds
ARM: 7349/1: integrator: convert to sparse irqs
ARM: 7259/3: net: JIT compiler for packet filters
ARM: 7334/1: add jump label support
ARM: 7333/2: jump label: detect %c support for ARM
ARM: 7338/1: add support for early console output via semihosting
ARM: use set_current_blocked() and block_sigmask()
ARM: exec: remove redundant set_fs(USER_DS)
ARM: 7332/1: extract out code patch function from kprobes
ARM: 7331/1: extract out insn generation code from ftrace
ARM: 7330/1: ftrace: use canonical Thumb-2 wide instruction format
ARM: 7351/1: ftrace: remove useless memory checks
ARM: 7316/1: kexec: EOI active and mask all interrupts in kexec crash path
ARM: Versatile Express: add NO_IOPORT
ARM: get rid of asm/irq.h in asm/prom.h
ARM: 7319/1: Print debug info for SIGBUS in user faults
ARM: 7318/1: gic: refactor irq_start assignment
ARM: 7317/1: irq: avoid NULL check in for_each_irq_desc loop
ARM: 7315/1: perf: add support for the Cortex-A7 PMU
...
intc_ack_data is flagged as __init when it shouldn't be, causing section
mismatches in non-init paths like intc_set_ack_handle():
WARNING: drivers/built-in.o(.text+0x5d760):
Section mismatch in reference from the function
intc_set_ack_handle() to the function .init.text:intc_ack_data()
The function intc_set_ack_handle()
references the function __init intc_ack_data().
This is often because intc_set_ack_handle lacks a __init
annotation or the annotation of intc_ack_data is wrong.
Reported-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SH intc has a compile time dependency on NR_IRQS. Make this dependency a
local define so that shmobile (and ARM in general) can have run-time
NR_IRQS setting.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
This ensures that the sense/prio lists are sorted at registration time,
enabling us to use a simple binary search for an optimized lookup
(something that had been on the TODO for some time).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
intc_set_affinity() updates the cpumask in place, so there's no need for
the upper layer to do this itself.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
It's possible to use IRQCHIP_SKIP_SET_WAKE to get the behaviour that
we're after, without having to bother with a dummy ->set_wake() callback
for the IRQ chip.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Various problems will happen if clk parent was set up directly.
it should use clk_reparent()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.15 (GNU/Linux)
iEYEABECAAYFAk8Obj8ACgkQGkmNcg7/o7hzngCfS5az4ZP3D+e/cvatHZm/nAzn
0mIAoKbYyXpLXGkEN+yDkd5YZAYwQjVR
=kryV
-----END PGP SIGNATURE-----
Merge tag 'rmobile-for-linus' of git://github.com/pmundt/linux-sh
SH/R-Mobile updates for 3.3 merge window.
* tag 'rmobile-for-linus' of git://github.com/pmundt/linux-sh: (32 commits)
arm: mach-shmobile: add a resource name for shdma
ARM: mach-shmobile: r8a7779 SMP support V3
ARM: mach-shmobile: Add kota2 defconfig.
ARM: mach-shmobile: Add marzen defconfig.
ARM: mach-shmobile: r8a7779 power domain support V2
ARM: mach-shmobile: Fix up marzen build for recent GIC changes.
ARM: mach-shmobile: r8a7779 PFC function support
ARM: mach-shmobile: Flush caches in platform_cpu_die()
ARM: mach-shmobile: Allow SoC specific CPU kill code
ARM: mach-shmobile: Fix headsmp.S code to use CPUINIT
ARM: mach-shmobile: clock-r8a7779: clkz/clkzs support
ARM: mach-shmobile: clock-r8a7779: add DIV4 clock support
ARM: mach-shmobile: Marzen LAN89218 support
ARM: mach-shmobile: Marzen SCIF2/SCIF4 support
ARM: mach-shmobile: r8a7779 PFC GPIO-only support V2
ARM: mach-shmobile: r8a7779 and Marzen base support V2
sh: pfc: Unlock register support
sh: pfc: Variable bitfield width config register support
sh: pfc: Add config_reg_helper() function
sh: pfc: Convert index to field and value pair
...
When CONFIG_PM_RUNTIME is off, drivers/sh/pm_runtime.o still has to be
built on sh platforms, because then it provides means to statically
switch on device PM clocks.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
sh_clk_init_parent() are using clk->mapped_reg
which is mapped in clk_register()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add PFC support for a 32-bit unlock register. Needed to
drive the r8a7779 PFC that comes with a funky PMMR register.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add support for variable config reg hardware by adding
the macro PINMUX_CFG_REG_VAR(). The width of each bitfield
needs to be passed to the macro, and the correct space must
be consumed by each bitfield in the enum table following the
macro. Data registers still need to have fixed bitfields.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add a helper function for shared config reg access
calculations. This allows us to reduce the amount
of duplicated code, and at the same time prepare
for a common place for future variable bitwidth
config reg support.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Update the way the PFC code is passing bitfield
selection between configure register functions.
Convert the code from using index only to bitfield
number and selected value. First step towards future
variable bitfield width support.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Introduce gpio_read_bit() for data register read access
and modify sh_gpio_get_value() to make use of the new
function instead of gpio_read_reg(). The purpose of
this change is to update the code to only use the
gpio_read_reg() function for config register access.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'pm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (76 commits)
PM / Hibernate: Implement compat_ioctl for /dev/snapshot
PM / Freezer: fix return value of freezable_schedule_timeout_killable()
PM / shmobile: Allow the A4R domain to be turned off at run time
PM / input / touchscreen: Make st1232 use device PM QoS constraints
PM / QoS: Introduce dev_pm_qos_add_ancestor_request()
PM / shmobile: Remove the stay_on flag from SH7372's PM domains
PM / shmobile: Don't include SH7372's INTCS in syscore suspend/resume
PM / shmobile: Add support for the sh7372 A4S power domain / sleep mode
PM: Drop generic_subsys_pm_ops
PM / Sleep: Remove forward-only callbacks from AMBA bus type
PM / Sleep: Remove forward-only callbacks from platform bus type
PM: Run the driver callback directly if the subsystem one is not there
PM / Sleep: Make pm_op() and pm_noirq_op() return callback pointers
PM/Devfreq: Add Exynos4-bus device DVFS driver for Exynos4210/4212/4412.
PM / Sleep: Merge internal functions in generic_ops.c
PM / Sleep: Simplify generic system suspend callbacks
PM / Hibernate: Remove deprecated hibernation snapshot ioctls
PM / Sleep: Fix freezer failures due to racy usermodehelper_is_disabled()
ARM: S3C64XX: Implement basic power domain support
PM / shmobile: Use common always on power domain governor
...
Fix up trivial conflict in fs/xfs/xfs_buf.c due to removal of unused
XBT_FORCE_SLEEP bit
This resolves the conflict in the arch/arm/mach-s3c64xx/s3c6400.c file,
and it fixes the build error in the arch/x86/kernel/microcode_core.c
file, that the merge did not catch.
The microcode_core.c patch was provided by Stephen Rothwell
<sfr@canb.auug.org.au> who was invaluable in the merge issues involved
with the large sysdev removal process in the driver-core tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since the SH7372's INTCS in included into syscore suspend/resume,
which causes the chip to be accessed when PM domains have been
turned off during system suspend, the A4R domain containing the
INTCS has to stay on during system sleep, which is suboptimal
from the power consumption point of view.
For this reason, add a new INTC flag, skip_syscore_suspend, to mark
the INTCS for intc_suspend() and intc_resume(), so that they don't
touch it. This allows the A4R domain to be turned off during
system suspend and the INTCS state is resrored during system
resume by the A4R's "power on" code.
Suggested-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
After all sysdev classes are ported to regular driver core entities, the
sysdev implementation will be entirely removed from the kernel.
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for non-entity mapped PFC registers through
the use of struct resource and ioremap()/iounmap().
The PFC main data structure gets updated with a pointer
to a struct resources array that point out all register
windows used by the PFC instance. The register definitions
are kept as physical addresses but the PFC code will do
transparent conversion into virtual addresses whenever
register windows are specified using with struct resource.
To introduce as little performance penalty as possible the
virtual address of each data register is cached in memory.
The virtual address of each configuration register is however
calculated during run time. This because the configuration
is considered slow path so focus is instead put on keeping
memory foot print as small as possible.
The PFC register access code is in this patch updated from
__raw_readN() / __raw_writeN() into ioreadN() / iowriteN().
This patch is needed to support the PFC block in r8a7779.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Convert the CPG DIV6 helper code to use the new mapped_reg
together with ioread32() and iowrite32().
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Convert the CPG DIV4 helper code to use the new mapped_reg
together with ioread32() and iowrite32().
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Convert the CPG MSTP32 helper code to use the new mapped_reg
together with ioread32() and iowrite32().
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add a "mapped_reg" member to struct clk and use that
to keep the ioremapped register based on enable_reg.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Some clocks can select its parent clock by CPG register.
But it might have been modified by boot-loader or something.
This patch removed fixed initial parent clock,
and setup it from their current register settings.
It works on div6 reparent clocks for now.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Switch sh7723 to a runtime PM implementation, common with ARM-based
sh-mobile platforms.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Switch sh7722 to a runtime PM implementation, common with ARM-based
sh-mobile platforms.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Switch sh7724 to a runtime PM implementation, common with ARM-based
sh-mobile platforms.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that all of the named string association with clocks has been
migrated to clkdev lookups there's no meaningful named topology that can
be constructed for a debugfs tree view. Get rid of the left over bits,
and shrink struct clk a bit in the process.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The runtime PM platform support stub in use by ARM-based SH/R-Mobile
platforms contains nothing that's specifically ARM-related and instead of
wholly generic to anything using the clock framework.
The recent runtime PM changes interact rather badly with the lazy
disabling of clocks late in the boot process through the clock framework,
leading to situations where the runtime suspend/resume paths are entered
without a clock being actively driven due to having been lazily gated
off.
In order to correct this we can trivially tie in the aforementioned stub
as a general fallback for all SH platforms that don't presently have
their own runtime PM implementations (the corner case being SH-based
SH-Mobile platforms, which have their own stub through the hwblk API --
which in turn has bitrotted and will be subsequently adapted to use the
same stub as everyone else), regardless of whether the platforms choose
to define power domains of their own or not.
This fixes up regressions for clock framework users who also build in
runtime PM support without any specific power domains of their own, which
was previously causing the serial console to be lost when warring with
lazy clock disabling.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
Enable IRQ_TYPE_EDGE_BOTH on all R/SH-Mobile ARM SoCs.
This hardware feature is supported by sh7367, sh7377,
sh7372 and sh73a0.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This provides a clk_rate_mult_range_round() helper for use by some of the
CPG PLL ranged multipliers, following the same approach as used by the
div ranges.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This is exporting symbols and will fail to build once we remove
the implicit presence of module.h
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
To fix:
arch/sh/drivers/dma/dma-sysfs.c:45:8: error: 'S_IRUGO' undeclared here (not in a function)
arch/sh/drivers/dma/dma-sysfs.c:75:8: error: 'S_IWUSR' undeclared here (not in a function)
make[4]: *** [arch/sh/drivers/dma/dma-sysfs.o] Error 1
drivers/sh/intc/core.c:449: error: 'S_IRUGO' undeclared here (not in a function)
make[5]: *** [drivers/sh/intc/core.o] Error 1
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This fix the problem that S_IRUSR and S_IWUSR are not solved in userimask.c.
-----
CC drivers/usb/host/r8a66597-hcd.o
drivers/sh/intc/userimask.c:57: error: ‘S_IRUSR’ undeclared here (not in a function)
drivers/sh/intc/userimask.c:57: error: ‘S_IWUSR’ undeclared here (not in a function)
CC drivers/watchdog/shwdt.o
-----
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add GPIO IRQ support to the shared PFC code in drivers/sh/pfc.c
The enums pointed out by a certain GPIO will be matched against
a table for IRQ to enum mappings.
Only the shared PFC code is updated by this patch. SoC specific
changes are also needed to allow platforms to make use of this
feature.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Clean up the f_width shift code in get_config_reg().
Reported-by: Ryusuke Sakato <ryusuke.sakato.bx@renesas.com>
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
R-Mobile SoCs such as sh73a0 include PINT blocks in INTC
that come with 2-bit IRQ trigger support. Add code to make
sure the bit width is checked so 4-bit only modes like for
instance EDGE_BOTH will fail for PINT.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
IRQ-capable GPIOs on sh7372 can be configured to produce interrupts on
both edges.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This V2 patch changes the clock disabling behavior during boot.
Two different changes are made:
1) Delay disabling of clocks until late in the boot process.
This fixes an existing issue where in-use clocks without
software reference are disabled by mistake during boot.
One example of this is the handling of the Mackerel serial
console output that shares clock with the I2C controller.
2) Write out the "disabled" state to the hardware for clocks
that not have been used by the kernel. In other words,
make sure so far unused clocks actually get turned off.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Extend the SH / SH-Mobile ARM clock framework to only
resume clocks that have been enabled.
Without this fix divide-by-zero is triggering on sh7372
FSIDIV during system wide resume of Suspend-to-RAM.
Signed-off-by: Magnus Damm <damm@opensource.se>
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
div6 clock should not use arch_flags for clk_rate_table_build,
because SH_CLK_DIV6_EXT doesn't care .arch_flags.
clk->freq_table[] will be all CPUFREQ_ENTRY_INVALID without this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: stable@kernel.org
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
I missed that coccinelle does not fix up header files by default.
Reported-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: <lethal@linux-sh.org>
Convert the SuperH clocks framework and shared interrupt handling
code to using struct syscore_ops instead of a sysdev classes and
sysdevs for power managment.
This reduces the code size significantly and simplifies it. The
optimizations causing things not to be restored after creating a
hibernation image are removed, but they might lead to undesirable
effects during resume from hibernation (e.g. the clocks would be left
as the boot kernel set them, which might be not the same way as the
hibernated kernel had seen them before the hibernation).
This also is necessary for removing sysdevs from the kernel entirely
in the future.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Clear the valid flag is in the INTC code.
Without this fix bit 7 of the sense register
is mistakenly set.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Remove kobject.h from files which don't need it, notably,
sched.h and fs.h.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Presently the root node is initialized by way of kzalloc on the parent
data structure, which by chance happens to do the bulk of what an
explicit initialization does with GFP_NOWAIT semantics. This however is
more by luck than by design, and as we ideally want to permit radix node
allocations access to the emergency pools anyways, add in the proper
initializer with the desired mask.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The disabling of the init op for non-legacy clocks neglected to do the
same in the core clock framework, resulting in a build failure. Fix it
up.
Reported-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that clk_set_rate_ex() is gone, there is also no way to get at rate
setting algo id, which is now also completely unused. Kill it off before
new clock ops start using it.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
With the refactoring of the SH7722 clock framework some time ago this
abstraction has become unecessary. Kill it off before anyone else gets
the bright idea to start using it.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The radix tree retry logic got a bit of an overhaul and subsequently
broke the virtual IRQ subgroup build. Simply switch over to
radix_tree_deref_retry() as per the filemap changes, which the virq
lookup logic was modelled after in the first place.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
CC drivers/sh/clk/core.o
drivers/sh/clk/core.c: In function 'clk_round_parent':
drivers/sh/clk/core.c:574: warning: format '%lu' expects type 'long unsigned int', but argument 2 has type 'unsigned int'
drivers/sh/clk/core.c:594: warning: format '%lu' expects type 'long unsigned int', but argument 2 has type 'unsigned int'
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Sometimes it is possible and reasonable to adjust the parent clock rate to
improve precision of the child clock, e.g., if the child clock has no siblings.
clk_round_parent() is a new addition to the SH clock-framework API, that
implements such an optimization for child clocks with divisors, taking all
integer values in a range.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
According to the linux/clk.h definition we should be handing back an
errno value or a valid rate. This fixes up the case where 0 can be
returned for invalid frequencies or cases where rounding has no
selectable candidate.
Reported-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There's no need to iterative over every single irq_desc when we can
already work out which IRQs have a backing descriptor via the shiny new
for_each_active_irq(). Switch to that instead.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that the genirq code provides an IRQ bitmap of its own and the
necessary API to manipulate it, there's no need to keep our own version
around anymore.
In the process we kill off some unused IRQ reservation code, with future
users now having to tie in to the genirq API as normal.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This shuffles the clock framework code around to a drivers/sh/clk subdir,
to follow the intc split up. This will make it easier to subsequently
break things out as well as plug in different helpers for non-CPG users.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The end condition of for_each_frequency should care about
both clk_rate_table_round and clk_rate_div_range_round,
and using "correct max size" is a natural idea in later function.
To avoid data over flow, this patch didn't modify
clk_rate_div_range_round side as .max = div_max + 1.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
When updating the iterator macro an old argument assignment was used on
the initial assignment causing a fault on the table rounding. Fix it up.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds a new clk_rate_div_range_round() for implementing rate rounding
by divisor ranges. This can be used trivially by clocks that support
arbitrary ranged divisors without the need for rate table construction.
This should only be used by clocks that both have large divisor ranges in
addition to clocks that will never be arbitrarily scaled, as the lack of
a backing frequency table will prevent cpufreq from being able to do much
of anything with them.
Primarily intended for use as a ->recalc helper.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently the only assisted rate rounding is frequency table backed, but
there are cases where it's impractical to use a frequency table for
certain clocks (such as the FSIDIV case, which supports 65535 divisors),
and we wish to reuse the same rate rounding algorithm.
This breaks out the core of the rate rounding logic in to its own helper
routine and shuffles the frequency table logic around, switching to using
an iterator for the generic helper routine.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This implements support for ioremapping of register windows that
encapsulate clock control registers used by a struct clk, with
transparent sibling inheritance.
Root clocks at the top of a given topology often encapsulate the entire
register space of all of their sibling clocks, so this mapping can be
done once and handed down. A given clock enable/disable case maps out to
a single bit in a shared register, so this prevents creating multiple
overlapping mappings.
The mapping case breaks down in to a couple of different situations:
- Sibling clocks without a specific mapping.
- Root clocks without a specific mapping.
- Any of sibling/root clocks with a specific mapping.
Sibling clocks with no specified mapping will grovel up the clock chain
and install the root clock mapping unconditionally at registration time.
Root clocks without their own mappings have a dummy BSS-initialized
mapping inserted that is handed down the chain just like any other
mapping. This permits all of the sibling clock ops to read/write using
the mapping offsets without any special configuration, enabling them to
not care whether access ultimately goes through translatable or
untranslatable memory.
Any clock with its own mapping will have the window initialized at
registration time and be ready for use by its clock ops. Failure to
establish the mapping will prevent registration, so no additional sanity
checks are needed. Sibling clocks that double as parents for the moment
will not propagate their mapping down, but this is easily tunable if the
need arises.
All clock mappings are kref refcounted, with each instance of mapping
inheritance incrementing the refcount.
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Remove "name" and "id" from drivers/sh/ struct clk.
The struct clk members "name" and "id" are not used
now when matching is done through clkdev.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This splits up the sh intc core in to something more vaguely resembling
a subsystem. Most of the functionality was alread fairly well
compartmentalized, and there were only a handful of interdependencies
that needed to be resolved in the process.
This also serves as future-proofing for the genirq and sparseirq rework,
which will make some of the split out functionality wholly generic,
allowing things to be killed off in place with minimal migration pain.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
If lookups happen while the radix node still points to a subgroup
mapping, an IRQ hasn't yet been made available for the specified id, so
error out accordingly. Once the slot is replaced with an IRQ mapping and
the tag is discarded, lookup can commence as normal.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Many interrupts that share a single mask source but are on different
hardware vectors will have an associated register tied to an INTEVT that
denotes the precise cause for the interrupt exception being triggered.
This introduces the concept of IRQ subgroups in the intc core, where
a virtual IRQ map is constructed for each of the pre-defined cause bits,
and a higher level chained handler takes control of the parent INTEVT.
This enables CPUs with heavily muxed IRQ vectors (especially across
disjoint blocks) to break things out in to a series of managed chained
handlers while being able to dynamically lookup and adopt the IRQs
created for them.
This is largely an opt-in interface, requiring CPUs to manually submit
IRQs for subgroup splitting, in addition to providing identifiers in
their enum maps that can be used for lazy lookup via the radix tree.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This implements a scheme roughly analogous to the PowerPC virtual to
hardware IRQ mapping, which we use for IRQ to per-controller ID mapping.
This makes it possible for drivers to use the IDs directly for lookup
instead of hardcoding the vector.
The main motivation for this work is as a building block for dynamically
allocating virtual IRQs for demuxing INTC events sharing a single INTEVT
in addition to a common masking source.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The gpiolib debugfs entry takes a hammer approach and iterates over all
of the potential GPIOs, regardless of their type. The SH PFC code on the
other hand contains a variable mismash of input/output/function types
spread out sparsely, leading to situations where the debug code can
trigger an out of range enum for the type. Since we already have an error
path for out of range enums, we can just hand that up to the higher level
instead of the current BUG() behaviour.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently the pinmux code is a one-way thing, but there's nothing
preventing an unregistration if no one has grabbed any of the pins.
This will permit us to save a bit of memory on systems that require pin
demux for certain peripherals in the case where registration of those
peripherals fails, or they are otherwise not attached to the system.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Some controllers will need to be initialized lazily due to pinmux
constraints, while others may simply have no need to be brought online if
there are no backing devices for them attached. In this case it's still
necessary to be able to reserve their hardware vector map before dynamic
IRQs get a hold of them.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds in hardware IRQ auto-distribution support for SH-X3 proto CPUs,
following the SH7786 support.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This was killed off by a simplification patch previously that failed to
take the cpufreq use case in to account, so reinstate the old bounding
logic. The lowest rate bounding on the other hand was broken in that it
never actually got assigned a rate and the best fit rate was instead just
getting lucky based on the ordering of the rate table, fix this up so the
code actually does what it was intended to do originally.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add support for reparenting of div6 clocks on SuperH and SH-Mobile SoCs.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The use of highest and lowest in clk_rate_table_round() is completely bogus
and superfluous. Remove it.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
To actually output the _new_ clock rate it first has to be set.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Wrapping pr_fmt to the KBUILD_MODNAME prefix seems to be the trendy
thing to do these days, so just do that instead of manually tidying
up the stragglers.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Teach SH-Mobile ARM how to make use of the shared SH clock
framework. This commit is one atomic switch that dumps the
local hackery and instead links in the shared clock framework
code in drivers/sh. A few local functions are kept in clock.c.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Move the CPG helpers to drivers/sh/clk-cpg.c V2.
This to allow SH-Mobile ARM to share the code with
SH. All functions except the legacy CPG stuff is moved.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch is V2 of the SH clock framework move from
arch/sh/kernel/cpu/clock.c to drivers/sh/clk.c. All
code except the following functions are moved:
clk_init(), clk_get() and clk_put().
The init function is still kept in clock.c since it
depends on the SH-specific machvec implementation.
The symbols clk_get() and clk_put() already exist in
the common ARM clkdev code, those symbols are left in
the SH tree to avoid duplicating them for SH-Mobile ARM.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This implements support for hardware-managed IRQ balancing as implemented
by SH-X3 cores (presently only hooked up for SH7786, but can probably be
carried over to other SH-X3 cores, too).
CPUs need to specify their distribution register along with the mask
definitions, as these follow the same format. Peripheral IRQs that don't
opt out of balancing will be automatically distributed at the whim of the
hardware block, while each CPU needs to verify whether it is handling the
IRQ or not, especially before clearing the mask.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for hardware-assisted userspace irq masking for
special priority levels. Due to the SR.IMASK interactivity, only some
platforms implement this in hardware (including but not limited to
SH-4A interrupt controllers, and ARM-based SH-Mobile CPUs). Each CPU
needs to wire this up on its own, for now only SH7786 is wired up as an
example.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The printk loglevels are all over the place, make them a bit more
coherent, and add some registration notification while we're at it.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently the sysdevs are simply numbered based on the list position,
without having any direct way of figuring out which controller these are
actually mapping to. This provides a name attr for mapping out the chip
name.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
serial: sh-sci: remove duplicated #include
sh: Export uncached helper symbols.
sh: Fix up NUMA build for 29-bit.
serial: sh-sci: Fix build failure for non-sh architectures.
sh: Fix up uncached offset for legacy 29-bit mode.
sh: Support CPU affinity masks for INTC controllers.
Extend the INTC code with ioremap() support V2.
Support INTC controllers that are not accessible through
a 1:1 virt:phys window. Needed by SH-Mobile ARM INTCS.
The INTC code behaves as usual if the io window resource
is omitted. The slow phys->virt lookup only happens during
setup. The fast path code operates on virtual addresses.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Extend the INTC code to warn and return an error code
in the case of memory allocation failure.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This hooks up the ->set_affinity() for the INTC controllers, which can be
done as just a simple copy of the cpumask. The enable/disable paths
already handle SMP register strides, so we just test the affinity mask in
these paths to determine which strides to skip over.
The early enable/disable path happens prior to the IRQs being registered,
so we have no affinity mask established at that point, in which case we
just default to CPU_MASK_ALL. This is left as it is to permit the force
enable/disable code to retain existing semantics.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Paul Mundt