All zero read and write masks in the regmap config are used to signal no
special mask is needed and the bus defaults are used. In some devices
all zero read/write masks are the special mask and bus defaults should
not be used. To signal this a new variable is added.
For example SPI often sets bit 7 in address to signal to the device a
read is requested. On TI AFE44xx parts with SPI interfaces no bit
needs to be set as registers are either read or write only and the
operation can be determined from the address only. For this case both
masks must be zero to not effect the address.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SoundWire bus provides sdw_read() and sdw_write() APIs for Slave
devices to program the registers. Provide support in regmap for
SoundWire bus.
Signed-off-by: Hardik T Shah <hardik.t.shah@intel.com>
Signed-off-by: Sanyog Kale <sanyog.r.kale@intel.com>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the hwlock id 0 is valid for hardware spinlock core, but now id 0
is treated as one invalid value for regmap. Thus we should add one extra
flag for regmap config to indicate if a hardware spinlock should be used,
then id 0 can be valid for regmap to request.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support to read/write SLIMbus value elements.
Currently it only supports byte read/write. Adding this support in
regmap would give codec drivers more flexibility when there are more
than 2 control interfaces like SLIMbus, i2c.
Without this patch each codec driver has to directly call SLIMbus value
element apis, and this could would get messy once we want to add i2c
interface to it.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviwed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have a use case in the at24 EEPROM driver (recently converted to
using regmap instead of raw i2c/smbus calls) where we read from/write
to the regmap in a loop, while protecting the entire loop with
a mutex.
Currently this implicitly makes us use two mutexes - one in the driver
and one in regmap. While browsing the code for similar use cases I
noticed a significant number of places where locking *seems* redundant.
Allow users to completely disable any locking mechanisms in regmap
config.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Mark Brown <broonie@kernel.org>
On some platforms, when reading or writing some special registers through
regmap, we should acquire one hardware spinlock to synchronize between
the multiple subsystems. Thus this patch adds the hardware spinlock
support for regmap.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
When we pass the result of a multiplication as the timeout or the delay,
we can get a warning from gcc-7:
drivers/mmc/host/bcm2835.c:596:149: error: '*' in boolean context, suggest '&&' instead [-Werror=int-in-bool-context]
drivers/mfd/arizona-core.c:247:195: error: '*' in boolean context, suggest '&&' instead [-Werror=int-in-bool-context]
drivers/gpu/drm/sun4i/sun4i_hdmi_i2c.c:49:27: error: '*' in boolean context, suggest '&&' instead [-Werror=int-in-bool-context]
The warning is a bit questionable inside of a macro, but this is
intentional on the side of the gcc developers. It is also an indication
of another problem: we evaluate the timeout and sleep arguments multiple
times, which can have undesired side-effects when those are complex
expressions.
This changes the two regmap variants to use local variables for storing
copies of the timeouts. This adds some more type safety, and avoids both
the double-evaluation and the gcc warning.
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=81484
Link: http://lkml.kernel.org/r/20170726133756.2161367-1-arnd@arndb.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds a macro regmap_field_read_poll_timeout that works
similar to the readx_poll_timeout defined in linux/iopoll.h, except
that this can also return the error value returned by a failed
regmap_field_read.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renamed variable "timeout" to "__timeout" & "pollret" to "__ret" to
avoid namespace collision. Tidy up macro arguments with parentheses.
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some irq controllers have writeonly/multipurpose register layouts. In
those cases we read invalid data back. Here we add the option
mask_writeonly as masking option.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Most of the kernel-doc comments in regmap don't actually generate
correctly. This patch fixes up a few common issues, corrects some typos
and adds some missing argument descriptions.
The most common issues being using a : after the function name which
causes the short description to not render correctly and not separating
the long and short descriptions of the function. There are quite a few
instances of arguments not being described or given the wrong name as
well.
This patch doesn't fixup functions/structures that are currently missing
descriptions.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As almost all of the callers of the regmap_read_poll_timeout macro
will include a local ret variable we will always get a Sparse warning
about the duplication of the ret variable:
warning: symbol 'ret' shadows an earlier one
Simply rename the ret variable in the marco to pollret to make this
significantly less likely to happen.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The readx_poll_timeout() macro calls usleep_range(), which is
declared in <linux/delay.h>.
Make include/linux/regmap.h include <linux/delay.h>, like
include/linux/iopoll.h does. Otherwise, users of the macro
will see "implicit declaration of function 'usleep_range'" error.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We currently only support masking the top bit for read and write
flags. Let's make the mask unsigned long and mask the bytes based
on the configured register length to make things more generic.
This allows using regmap for more exotic combinations like SPI
devices that need little endian addressing.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds a macro regmap_read_poll_timeout that works similar
to the readx_poll_timeout defined in linux/iopoll.h, except that this
can also return the error value returned by a failed regmap_read.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Regmap irq implements the generic interrupt service routine which
is common for most of devices. Some devices, like MAX77620, MAX20024
needs the special handling before and after servicing the interrupt
as generic. For the example, MAX77620 programming guidelines for
interrupt servicing says:
1. When interrupt occurs from PMIC, mask the PMIC interrupt by setting
GLBLM.
2. Read IRQTOP and service the interrupt accordingly.
3. Once all interrupts has been checked and serviced, the interrupt
service routine un-masks the hardware interrupt line by clearing
GLBLM.
The step (2) is implemented in regmap irq as generic routine. For
step (1) and (3), add callbacks from regmap irq to client driver
to handle chip specific configurations.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add device managed APIs for regmap_add_irq_chip() and
regmap_del_irq_chip() so that it can be managed by
device framework for freeing it.
This helps on following:
1. Maintaining the sequence of resource allocation and deallocation
regmap_add_irq_chip(&d);
devm_requested_threaded_irq(virq)
On free path:
regmap_del_irq_chip(d);
and then removing the irq registration.
On this case, regmap irq is deleted before the irq is free.
This force to use normal irq registration.
By using devm apis, the sequence can be maintain properly:
devm_regmap_add_irq_chip(&d);
devm_requested_threaded_irq(virq);
and resource deallocation will be done in reverse order
by device framework.
2. No need to delete the regmap_irq_chip in error path or remove
callback and hence there is less code on this path.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 23b92e4cf5fd ("regmap: remove regmap_write_bits()")
removed regmap_write_bits(), but MFD driver was using it.
So, commit e30fccd6771d ("regmap: Keep regmap_write_bits()")
turns out it, but it is using original style.
This patch uses regmap_update_bits_base() for regmap_write_bits()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch merges regmap_fields_update_bits() into macro
by using regmap_field_update_bits_base().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch merges regmap_fields_write() into macro
by using regmap_fields_update_bits_base().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds new regmap_fields_update_bits_base() which is using
regmap_update_bits_base().
Current regmap_fields_xxx() can be merged into it by macro.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch merges regmap_field_update_bits() into macro
by using regmap_field_update_bits_base().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch merges regmap_field_write() into macro
by using regmap_field_update_bits_base().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds new regmap_field_update_bits_base() which is using
regmap_update_bits_base().
Current regmap_field_xxx() can be merged into it by macro.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current regmap has many similar update functions like below,
but the difference is very few.
regmap_update_bits()
regmap_update_bits_async()
regmap_update_bits_check()
regmap_update_bits_check_async()
Furthermore, we can add *force* write option too in the future.
This patch merges regmap_update_bits_check_async() into macro
by using regmap_update_bits_base().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current regmap has many similar update functions like below,
but the difference is very few.
regmap_update_bits()
regmap_update_bits_async()
regmap_update_bits_check()
regmap_update_bits_check_async()
Furthermore, we can add *force* write option too in the future.
This patch merges regmap_update_bits_check() into macro
by using regmap_update_bits_base().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current regmap has many similar update functions like below,
but the difference is very few.
regmap_update_bits()
regmap_update_bits_async()
regmap_update_bits_check()
regmap_update_bits_check_async()
Furthermore, we can add *force* write option too in the future.
This patch merges regmap_update_bits_async() into macro
by using regmap_update_bits_base().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current regmap has many similar update functions like below,
but the difference is very few.
regmap_update_bits()
regmap_update_bits_async()
regmap_update_bits_check()
regmap_update_bits_check_async()
Furthermore, we can add *force* write option too in the future.
This patch merges regmap_update_bits() into macro
by using regmap_update_bits_base().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current regmap has many similar update functions like below,
but the difference is very few.
regmap_update_bits()
regmap_update_bits_async()
regmap_update_bits_check()
regmap_update_bits_check_async()
Furthermore, we can add *force* write option too in the future.
This patch adds new regmap_update_bits_base() which is feature
merged function. Above functions can be merged into it by macro.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add device managed APIs for regmap_add_irq_chip() and
regmap_del_irq_chip() so that it can be managed by
device framework for freeing it.
This helps on following:
1. Maintaining the sequence of resource allocation and deallocation
regmap_add_irq_chip(&d);
devm_requested_threaded_irq(virq)
On free path:
regmap_del_irq_chip(d);
and then removing the irq registration.
On this case, regmap irq is deleted before the irq is free.
This force to use normal irq registration.
By using devm apis, the sequence can be maintain properly:
devm_regmap_add_irq_chip(&d);
devm_requested_threaded_irq(virq);
and resource deallocation will be done in reverse order
by device framework.
2. No need to delete the regmap_irq_chip in error path or remove
callback and hence there is less code on this path.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The exact meaning of max_register is not entierly clear. Follow
the common wording and use "address" instead of "index".
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some of devices supports the trigger level for interrupt
like rising/falling edge specially for GPIOs. The interrupt
support of such devices may have uses the generic regmap irq
framework for implementation.
Add support to configure the trigger type device interrupt
register via regmap-irq framework. The regmap-irq framework
configures the trigger register only if the details of trigger
type registers are provided.
[Fixed use of terery operator for legibility -- broonie]
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In 8019ff6cfc ("regmap: Use reg_sequence for multi_reg_write / register_patch")
struct reg_default was renamed to struct reg_secquence, which missed
one place to fix up.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some buses provide a native _update_bits() operation which for uncached
registers is faster than doing a read/modify/write cycle as it is a
single bus transaction. Add support for implementing this to regmap.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWE+cLAAoJECTWi3JdVIfQaCcH/3m85peX2dlE7KhI6gL9N76h
v4w7phygbkQqdD3v9bbbiRavkOMrrBCVNZ28uXIO/52LulrK9pzxRVTuhqdyVasO
CIWfAYinlxWJA0BnJ1E2toqXkym9PEILCixfPyYEI5iZTX3w3rosSdup9MzYTxZZ
N3Vux2bjgCiXp9hYbajITFQ9QRNXzn3hlI/Jl0/x9SkodkzCLJurMq5JAaFE+mhO
1W2S+ERvb0M5bHuyr1Bhf3Bzb8uMFTl1QK3vxRkSI9UVe3MSpQP9SZeN+ye7p7U0
hDlike9FxyLTMMnIe9XnsNEtBZmxNuAb7meF50Bi7xzItRGOIlDxB/Ak55uD4I8=
=hCDC
-----END PGP SIGNATURE-----
Merge tag 'regmap-offload-update-bits' into regmap-next
regmap: Allow buses to provide a custom update_bits() operation
Some buses provide a native _update_bits() operation which for uncached
registers is faster than doing a read/modify/write cycle as it is a
single bus transaction. Add support for implementing this to regmap.
# gpg: Signature made Tue 06 Oct 2015 16:21:47 BST using RSA key ID 5D5487D0
# gpg: Oops: keyid_from_fingerprint: no pubkey
# gpg: Oops: keyid_from_fingerprint: no pubkey
# gpg: key 00000000 occurs more than once in the trustdb
# gpg: key 16005C11: no public key for trusted key - skipped
# gpg: key 16005C11 marked as ultimately trusted
# gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>"
# gpg: aka "Mark Brown <broonie@debian.org>"
# gpg: aka "Mark Brown <broonie@kernel.org>"
# gpg: aka "Mark Brown <broonie@tardis.ed.ac.uk>"
# gpg: aka "Mark Brown <broonie@linaro.org>"
# gpg: aka "Mark Brown <Mark.Brown@linaro.org>"
This commit allows installing a custom reg_update_bits function for cases where
the hardware provides a mechanism to set or clear register bits without a
read/modify/write cycle. Such is the case with the Microchip ENCX24J600.
If a custom reg_update_bits function is provided, it will only be used against
volatile registers.
Signed-off-by: Jon Ringle <jringle@gridpoint.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add REGMAP_IRQ_REG macro in regmap.h to define regmap_irq
structure easily for other driver module.
Signed-off-by: Qipeng Zha <qipeng.zha@intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
An user will be CSR SiRFSoC ARM chips.
Signed-off-by: Guo Zeng <Guo.Zeng@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some chips have separate unmask registers from mask registers for
some consideration of concurrency SMP write performance. And this
patch adds a flag for it.
An user will be CSR SiRFSoC ARM chips.
Signed-off-by: Guo Zeng <Guo.Zeng@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add functions to access the maximum size we can read/write using
regmap_raw_read/write().
This helps drivers that need to know how much they can write with the
raw functions without problems. There are some devices (e.g. bmc150)
that have fifos as registers which need to be read in specific chunks
otherwise samples are dropped.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are some buses which have a limit on the maximum number of bytes
that can be send/received. An example for this is
I2C_FUNC_SMBUS_I2C_BLOCK which does not support any reads/writes of more
than 32 bytes. The regmap_bulk operations should still be able to
utilize the full 32 bytes in this case.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are some fields of this struct undocumented or old. This patch
updates the missing comments.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Init functions defined in regmap*.c files are now prefixed with
__, take lockdep key and class parameters, and should not be
called directly: move the documentation to regmap.h, where the
macros are defined.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Lockdep validator complains about recursive locking and deadlock
when two different regmap instances are called in a nested order.
That happens anytime a regmap read/write call needs to access
another regmap.
This is because, for performance reason, lockdep groups all locks
initialized by the same mutex_init() in the same lock class.
Therefore all regmap mutexes are in the same lock class, leading
to lockdep "nested locking" warnings if a regmap accesses another
regmap.
In general, it is impossible to establish in advance the hierarchy
of regmaps, so we make sure that each regmap init call initializes
its own static lock_class_key. This is done by wrapping all
regmap_init calls into macros.
This also allows us to give meaningful names to the lock_class_key.
For example, in rt5677 case, we have in /proc/lockdep_chains:
irq_context: 0
[ffffffc0018d2198] &dev->mutex
[ffffffc0018d2198] &dev->mutex
[ffffffc001bd7f60] rt5677:5104:(&rt5677_regmap)->_lock
[ffffffc001bd7f58] rt5677:5096:(&rt5677_regmap_physical)->_lock
[ffffffc001b95448] &(&base->lock)->rlock
The above would have resulted in a lockdep recursive warning
previously. This is not the case anymore as the lockdep validator
now clearly identifies the 2 regmaps as separate.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add an optional delay_us field in reg_sequence to allow the client to
specify a delay (in microseconds) to be applied after any given write
in a sequence of writes.
We treat a delay in a sequence the same way we treat a page change as
they are logically similar in that you can coalesce all write before
a delay (in the same way you can coalesce all writes before a page
change is needed)
Signed-off-by: Nariman Poushin <nariman@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Separate the functionality using sequences of register writes from the
functions that take register defaults. This change renames the arguments
in order to support the extension of reg_sequence to take an optional
delay to be applied after any given register in a sequence is written.
This avoids adding an int to all register defaults, which could
substantially increase memory usage for regmaps with large default tables.
This also updates all the clients of multi_reg_write/register_patch.
Signed-off-by: Nariman Poushin <nariman@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
regmap_fields_force_write() is similar to regmap_fields_write(),
but regmap_fields_force_write() write data to register even though
it is same value.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
regmap_write_bits() is similar to regmap_update_bits(),
but regmap_write_bits() write data to register even though
it is same value.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch introduces regmap_get_reg_stride() function which would
be used by the infrastructures like nvmem framework built on top of
regmap. Mostly this function would be used for sanity checks on inputs
within such infrastructure.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch introduces regmap_get_max_register() function which would be
used by the infrastructures like nvmem framework built on top of
regmap.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix incorrect description of structure element "msb", which is
described as "reg".
Signed-off-by: Bintian Wang <bintian.wang@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the recently added support for bus operations to provide a standard
mapping for AC'97 register I/O.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Add a new function regmap_get_device to obtain the underlying struct
device from a regmap.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Some busses do not support sending/receiving multiple registers in one go.
Such kind of busses just unpack the registers that have been previously
packed by the regmap core or pack registers that will be later unpacked by
the core code.
Add reg_write and reg_read callbacks in order to optimize access through
this kind of busses.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Here's the big char/misc driver updates for 3.15-rc1.
Lots of various things here, including the new mcb driver subsystem.
All of these have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlM7ArIACgkQMUfUDdst+ylS+gCfcJr0Zo2v5aWnqD7rFtFETmFI
LhcAoNTQ4cvlVdxnI0driWCWFYxLj6at
=aj+L
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver patches from Greg KH:
"Here's the big char/misc driver updates for 3.15-rc1.
Lots of various things here, including the new mcb driver subsystem.
All of these have been in linux-next for a while"
* tag 'char-misc-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (118 commits)
extcon: Move OF helper function to extcon core and change function name
extcon: of: Remove unnecessary function call by using the name of device_node
extcon: gpio: Use SIMPLE_DEV_PM_OPS macro
extcon: palmas: Use SIMPLE_DEV_PM_OPS macro
mei: don't use deprecated DEFINE_PCI_DEVICE_TABLE macro
mei: amthif: fix checkpatch error
mei: client.h fix checkpatch errors
mei: use cl_dbg where appropriate
mei: fix Unnecessary space after function pointer name
mei: report consistently copy_from/to_user failures
mei: drop pr_fmt macros
mei: make me hw headers private to me hw.
mei: fix memory leak of pending write cb objects
mei: me: do not reset when less than expected data is received
drivers: mcb: Fix build error discovered by 0-day bot
cs5535-mfgpt: Simplify dependencies
spmi: pm: drop bus-level PM suspend/resume routines
spmi: pmic_arb: make selectable on ARCH_QCOM
Drivers: hv: vmbus: Increase the limit on the number of pfns we can handle
pch_phub: Report error writing MAC back to user
...
This is the implementation of regmap_multi_reg_write()
There is a new capability 'can_multi_write' that device drivers
must set in order to use this multi reg write mode.
This replaces the first definition, which just defined the API.
Signed-off-by: Anthony Olech <anthony.olech.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In some cases, we need regmap's format parse_val function
to do be/le translation according to the bus configuration.
For example, snd_soc_bytes_put() uses regmap to write/read values,
and use cpu_to_be() directly to covert MASK into big endian. This
is a defect, and should use regmap's format function to do it according
to bus configuration.
Signed-off-by: Nenghua Cao <nhcao@marvell.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Devices with more complex boot proceedures may occasionally apply the
register patch manual. regmap_multi_reg_write is a logical way to do so,
however the patch must be applied with cache bypass on, such that it
doesn't override any user settings. This patch adds a
regmap_multi_reg_write_bypassed function that applies a set of writes
with the bypass enabled.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
There should be no need for the writes supplied to this function to be
edited by it so mark them as const.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Create special function regmap_attach_dev
which can be called separately out of regmap_init.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
SPMI states that a slave may contain two register spaces, the Base
register space is a 5-bit byte-addressable space accessed via the
Register Read/Write and Register Zero Write command sequences, and the
Extended register space: a 16-bit byte-addressable space accessed via
the Extended Read/Write and Extended Read/Write Long command sequences.
Provide support for accessing both of these spaces, taking advantage of
the more bandwidth-efficient commands ('Register 0 Write' vs 'Register
Write', and 'Extended Register Read/Write' vs 'Extended Register
Read/Write Long') when possible.
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
Acked-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These sentences are not proper English due to the typos. I had initially caught
one of them while trying to understand the regmap feature, and then I just ran
the vim spell checker, and went through all the items that would need to be
fixed for this header file.
Signed-off-by: Laszlo Papp <lpapp@kde.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
In some cases, clear interrupt register may be at address 0.
This patch allows to use such configurations by adding additional
configuration bit to indicate this.
[With doc fix from Levente Kurusa <levex@linux.com> -- broonie]
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add basic support for the System Power Management Interface (SPMI) bus.
This is a simple implementation which only implements register accesses
via the Extended Register Read/Write Long commands.
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
New API regmap_multi_reg_write() is defined that allows a set of reg,val
pairs to be written to a I2C client device as one block transfer from the
point of view of a single I2C master system.
A simple demonstration implementation is included that just splits the
block write request into a sequence of single register writes.
The implementation will be modified later to support those I2C clients
that implement the alternative non-standard MULTIWRITE block write mode
so to achieve a single I2C transfer that will be atomic even in multiple
I2C master systems.
Signed-off-by: Anthony Olech <anthony.olech.opensource@diasemi.com>
Signed-off-by: David Dajun Chen <david.chen@diasemi.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make it easier for drivers to include single register writes in
asynchronous sequences by providing async versions of the write
and update bits operations. The update bits operations are only
likely to be effective when used with devices that have caches
but this is common enough to be useful.
Signed-off-by: Mark Brown <broonie@linaro.org>
Add helper macro to set the min and max value of the register range.
This is useful when initialising the register ranges of the device like
static const struct regmap_range readable_ranges[] = {
regmap_reg_range(DEVICE_REG0, DEVICE_REG10),
};
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current Linux kernel is supporting regmap_field method
and it is very useful feature.
It needs one regmap_filed for one register access.
OTOH, there is multi port device which
has many same registers in the market.
The difference for each register access is
only its address offset.
Current API needs many regmap_field for such device,
but it is not good.
This patch adds new regmap_fileds API which can care
about multi port/offset access via regmap.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current regmap_field is supporting read/write functions.
This patch adds new update_bits function for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
A quiet release for regmap, some cleanups, fixes and:
- Improved node coalescing for rbtree, reducing memory usage and
improving performance during syncs.
- Support for registering multiple register patches.
- A quirk for handling interrupts that need to be clear when masked
in regmap-irq.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=um4f
-----END PGP SIGNATURE-----
Merge tag 'regmap-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"A quiet release for regmap, some cleanups, fixes and:
- Improved node coalescing for rbtree, reducing memory usage and
improving performance during syncs.
- Support for registering multiple register patches.
- A quirk for handling interrupts that need to be clear when masked
in regmap-irq"
* tag 'regmap-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: rbtree: Make cache_present bitmap per node
regmap: rbtree: Reduce number of nodes, take 2
regmap: rbtree: Simplify adjacent node look-up
regmap: debugfs: Fix continued read from registers file
regcache-rbtree: Fix reg_stride != 1
regmap: Allow multiple patches to be registered
regmap: regcache: allow read-only regs to be cached
regmap: fix regcache_reg_present() for empty cache
regmap: core: allow a virtual range to cover its own data window
regmap: irq: document mask/wake_invert flags
regmap: irq: make flags bool and put them in a bitfield
regmap: irq: Allow to acknowledge masked interrupts during initialization
regmap: Provide __acquires/__releases annotations
The use of WARN_ON() needs the definitions from bug.h, without it
you can get:
include/linux/regmap.h: In function 'regmap_write':
include/linux/regmap.h:525:2: error: implicit declaration of function 'WARN_ONCE' [-Werror=implicit-function-declaration]
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
regmap.h requires linux/err.h if CONFIG_REGMAP is not defined. Without it I get
error.
CC drivers/media/platform/exynos4-is/fimc-reg.o
In file included from drivers/media/platform/exynos4-is/fimc-reg.c:14:0:
include/linux/regmap.h: In function ‘regmap_write’:
include/linux/regmap.h:525:10: error: ‘EINVAL’ undeclared (first use in this function)
include/linux/regmap.h:525:10: note: each undeclared identifier is reported only once for each function it appears in
Signed-off-by: Mateusz Krawczuk <m.krawczuk@partner.samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@kernel.org
This patch makes mask/wake_invert bool and puts all flags into a bitfield
for consistency and to save some space.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
In case the hardware interrupt mask register does not prevent the chip level
irq from being asserted by the corresponding interrupt status bit, already
set interrupt bits should to be cleared once after masking them during
initialization. Add a flag to let drivers enable this behavior.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Mark Brown