Also use them instead of a magic value when enabling the interrupts.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
at803x currently automatically enables the RGMII TX clock delay when the
phy interface mode is PHY_INTERFACE_MODE_RGMII_TXID. The same should be
done when PHY_INTERFACE_MODE_RGMII_ID is specified.
Use a similar logic to enable the RGMII RX clock delay as well.
at803x_context_{save,restore} were not touched because these are only
used on AR8030 which is a RMII phy (RGMII clock delays are irrelevant).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 8030 is only a "RMII Fast Ethernet PHY", thus it must not have the
SUPPORTED_1000* bits set.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The operstate of a networking device initially IF_OPER_UNKNOWN aka
"unknown", updated on carrier state changes (with carrier state being on
by default). This means it will stay unknown unless the carrier state
goes to off at some point, which is not the case if the phy is already
up/connected at startup.
Explicitly turn off the carrier on phy attach, leaving the phy state
machine to turn the carrier on when it has done the initial negotiation.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
It used to be that bus->irq was a pointer but after e7f4dc3536
('mdio: Move allocation of interrupts into core') it's an array inside
the mdio struct, so it can never be NULL. Let's remove the check.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If bus = kzalloc() fails then we end up dereferencing bus when we do
"bus->irq[i] = PHY_POLL;". The code is a little simpler if we reverse
the NULL check and return directly on failure.
Fixes: e7f4dc3536 ('mdio: Move allocation of interrupts into core')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/bonding/bond_main.c
drivers/net/ethernet/mellanox/mlxsw/spectrum.h
drivers/net/ethernet/mellanox/mlxsw/spectrum_switchdev.c
The bond_main.c and mellanox switch conflicts were cases of
overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
LAN8740 has a different phy_id than LAN8710/LAN8720.
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 651df21835 ("phy: micrel: Fix finding PHY properties in MAC
node.") only fixes finding PHY properties in MAC node for KSZ9021. This
commit applies the same fix for KSZ9031.
Fixes: 8b63ec1837 ("phylib: Make PHYs children of their MDIO bus, not the bus' parent.")
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Henri Roosen <henri.roosen@ginzinger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make device_free and device_remove operations in the mdio device
structure, so the core code does not need to differentiate between
phy devices and generic mdio devices.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all devices on an MDIO bus are PHYs. Meaning not all MDIO drivers
are PHY drivers. Add support for generic MDIO drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make it clear that mdiobus_scan () will only find devices which have a
vendor/product ID in registers 2 and 3. These are typically PHY
devices. Other sort of MDIO devices, such as switches, are not
expected to be found during the scan.
Similarly, __mdiobus_register(), which calls mdiobus_scan() will only
find PHY devices, and other sorts of MDIO devices are expected to be
instantiated from device tree.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function should work with any sort of MDIO device which can be
probed on the bus, not just PHY devices. So generalise it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matching a driver to a device has both generic parts, and parts which
are specific to PHY devices. Move the PHY specific parts into
phy_device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than have each driver set the driver owner field, do it once in
the core code. This will also help with later changes, when the device
structure will move.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MDIO PM operations are really PHY device PM operations. So move
them into phy_device. This will be needed when we support devices on
the mdio bus which are not PHYs.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mdio_bus exports three attributes:
- PHY ID is the unique 32-bits identifier for a MDIO device implementing
standard MII registers MII_PHYSID1/2, which is not guaranteed to be the
case for non-standard compliant devices (e.g: Ethernet switches)
- PHY interface describes the data-path of the PHY/MDIO device, which is
not strictly a PHY thing, but is required and needed for PHY devices to
function, a MDIO device could be a control device exclusively
- PHY has fixups describes what the PHY driver may have done, so
completely PHY specific
These are all phy attributes, not generic mdio attributes. So move the
attributes into the phy device code.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than have drivers directly manipulate the mii_bus structure,
provide and API for registering and unregistering devices on an MDIO
bus, and performing lookups.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all devices attached to an MDIO bus are phys. So add an
mdio_device structure to represent the generic parts of an mdio
device, and place this structure into the phy_device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Have mdio_alloc() create the array of interrupt numbers, and
initialize it to POLLING. This is what most MDIO drivers want, so
allowing code to be removed from the drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than use devm_kzalloc(), use the mdio helper function.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many Ethernet drivers contain the same netdev_info() print statement
about the attached phy. Move it into the phy device code. Additionally
add a varargs function which can be used to append additional
information.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The address of the device can be determined from the phydev structure,
rather than passing it as a parameter.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a phydev_name() function, to help with moving some structure members
from phy_device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for moving some of the phy_device structure members,
add macros for printing errors and debug information.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY counters receiver errors and errors while idle.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY counters receiver errors and errors while idle.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/geneve.c
Here we had an overlapping change, where in 'net' the extraneous stats
bump was being removed whilst in 'net-next' the final argument to
udp_tunnel6_xmit_skb() was being changed.
Signed-off-by: David S. Miller <davem@davemloft.net>
mdiobus_alloc() might return NULL, but its return value is not
checked in mdio_mux_init(). This could potentially lead to a NULL
pointer dereference. Fix it by checking the return value
Fixes: 0ca2997d14 ("netdev/of/phy: Add MDIO bus multiplexer support.")
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 8b63ec1837 ("phylib: Make PHYs children of their MDIO bus,
not the bus' parent.") changed the parenting of PHY devices, making
them a child of the MDIO bus, instead of the MAC device. This broken
the Micrel PHY driver which has a deprecated feature of allowing PHY
properties to be placed into the MAC node.
In order to find the MAC node, we need to walk up the tree of devices
until we find one with an OF node attached.
Reported-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Suggested-by: David Daney <david.daney@cavium.com>
Acked-by: David Daney <david.daney@cavium.com>
Fixes: 8b63ec1837 ("phylib: Make PHYs children of their MDIO bus, not the bus' parent.")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device tree properties for a phy device are expected to be in the phy
node. The current code for the DP83867 also tries to look in the
parent node. The devices binding documentation does not mention this,
no current device tree file makes use of this, and it is not behaviour
we want. So remove looking in the parent device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/renesas/ravb_main.c
kernel/bpf/syscall.c
net/ipv4/ipmr.c
All three conflicts were cases of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible to address another chip on same MDIO bus. The case is
correctly handled for media advertising. It is taken into account
only if mii_data->phy_id == phydev->addr. However, this condition
was missing for reset case.
Signed-off-by: Jérôme Pouiller <jezz@sysmic.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a PHY entry for the Broadcom BCM7435 chips, this is a 40nm
generation Ethernet PHY which is analogous to its 7425 and 7429 counter
parts.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit fcb26ec5b1 ("broadcom: move all PHY_ID's to header")
updated broadcom_tbl to use PHY_IDs, but incorrectly replaced 0x0143bca0
with PHY_ID_BCM5482 (making a duplicate entry, and completely omitting
the original). Fix that.
Fixes: fcb26ec5b1 ("broadcom: move all PHY_ID's to header")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NOLINK state will poll the phy once a second to see if the link
has come up. If the phy has an interrupt line, this polling can be
skipped, since the phy should interrupt when the link returns.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 88E1540 can be found embedded in the Marvell 88E6352 switch. It
is compatible with the 88E1510, so add support for it, using the
88E1510 specific functions.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for the Vitesse VSC8601 PHY. Generic functions are
used for everything except interrupt handling.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 77a993942 "phy/at8031: enable at8031 to work on interrupt mode"
added interrupt support for the 8031 PHY but left out the other two
chips supported by this driver.
This patch sets the .ack_interrupt and .config_intr functions for the
8030 and 8035 drivers as well.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWOehzAAoJECTWi3JdVIfQTPYH+wYMDG8gAIw2s0AJ4DvVe4qZ
sOAm1UgUJZxssrEA6BNqbfM0dfRo+oQJKmRd0Dc5n7LEMsYHdI/5yKHk8PCS6ZzD
iQyQCzbd0thDAqwuPaMP62cyPDHwyJX22VGTsgVnj6AZqAQ+9+g4SPKhFnm1Mlm4
hmDi6fdSrsqo8k8gkpVN8RFOfVsjAV1dLtAauQRWDHrqMxXURSrKG76eqAqUa5bn
BLPXBoj5PA0DMLPO2j+ADZwWN723LrI2mSSlc+ThjEX/OIt2OhAoiOTV5RPqaafy
TIsCkh68q/gYAsL5HtvvmgZByl41FLYiO0Z+rXmWUyMMbnvhZTLws9S2BNpBLuk=
=DgXG
-----END PGP SIGNATURE-----
Merge tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver"
* tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (87 commits)
spi: pxa2xx: Rework self-initiated platform data creation for non-ACPI
spi: pxa2xx: Add support for Intel Broxton
spi: pxa2xx: Detect number of enabled Intel LPSS SPI chip select signals
spi: pxa2xx: Add output control for multiple Intel LPSS chip selects
spi: pxa2xx: Use LPSS prefix for defines that are Intel LPSS specific
spi: Add DSPI support for layerscape family
spi: ti-qspi: improve ->remove() callback
spi/spi-xilinx: Fix race condition on last word read
spi: Drop owner assignment from spi_drivers
spi: Add THIS_MODULE to spi_driver in SPI core
spi: Setup the master controller driver before setting the chipselect
spi: dw: replace magic constant by DW_SPI_DR
spi: mediatek: mt8173 spi multiple devices support
spi: mediatek: handle controller_data in mtk_spi_setup
spi: mediatek: remove mtk_spi_config
spi: mediatek: Update document devicetree bindings to support multiple devices
spi: fix kernel-doc warnings about missing return desc in spi.c
spi: fix kernel-doc warnings about missing return desc in spi.h
spi: pxa2xx: Align a few defines
spi: pxa2xx: Save other reg_cs_ctrl bits when configuring chip select
...
Minor overlapping changes in net/ipv4/ipmr.c, in 'net' we were
fixing the "BH-ness" of the counter bumps whilst in 'net-next'
the functions were modified to take an explicit 'net' parameter.
Signed-off-by: David S. Miller <davem@davemloft.net>
In the packet timestamping function, check that the ptp version and
protocol of the packet matches what we have configured the hardware to
actually generate timestamps for, before looking/waiting for a timestamp.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The list of rx timestamps are currently only pruned of old entries when a
new entry is inserted. If no new entries are added, old timestamps may
survive beyond their lifetime, possible causing them to be attached to
packets with the same sequence number after a rollover.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently rx_timestamp_work reschedules itself as a regular workqueue item,
effectively causing it run constantly as long as there are packets left in
the queue. Fix by using delayed workqueue items, limiting it to run only
every two jiffies.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only using the message type and sequence id for matching timestamps
with packets is error prone, as multiple clients may very well be
sending packets with the same messagetype and timestamp at the same
time. Fix by extending the check to include the hash of bytes 20-29
(source id in PTPv2) that is provided with the timestamps.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When probing devices-in-package for a c45 phy, device zero is the last
device to probe, however, if driver reads 0 from device zero,
c45_ids->devices_in_package is set to '0', the loop condition of probing
will be matched again, see codes below:
for (i = 1;i < num_ids && c45_ids->devices_in_package == 0;i++)
driver will run in a dead loop.
This patch restructures the bug and confusing loop, it provides a helper
function get_phy_c45_devs_in_pkg which to read devices-in-package registers
of a MMD, and rewrites the loop with using the helper function.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An spi_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Martin Blumenstingl