This add an ioctl to migrate a range of process address space to the
device memory. On platform without cache coherent bus (x86, ARM, ...)
this means that CPU can not access that range directly, instead CPU
will fault which will migrate the memory back to system memory.
This is behind a staging flag so that we can evolve the API.
Signed-off-by: Jérôme Glisse <jglisse@redhat.com>
Device memory can be use in SVM, in which case we do not have any of
the existing buffer object. This commit add infrastructure to allow
use of device memory without nouveau_bo. Again this is a temporary
solution until a rework of GPU memory management.
Signed-off-by: Jérôme Glisse <jglisse@redhat.com>
This uses HMM to mirror a process' CPU page tables into a channel's page
tables, and keep them synchronised so that both the CPU and GPU are able
to access the same memory at the same virtual address.
While this code also supports Volta/Turing, it's only enabled for Pascal
GPUs currently due to channel recovery being unreliable right now on the
later GPUs.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
For a channel to make use of SVM features, it requires a different GPU MMU
configuration than we would normally use, which is not desirable to switch
to unless a client is actively going to use SVM.
In order to supporting SVM without more extensive changes to the userspace
interfaces, the SVM_INIT ioctl needs to replace the previous configuration
safely.
The only way we can currently do this safely, accounting for some unlikely
failure conditions, is to allocate the new VMM without destroying the last
one, and prioritising the SVM-enabled configuration in the code that cares.
This will get cleaned up again further down the track.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
There's no need to avoid using copy engines if gr init fails for some
reason (usually missing FW, or incomplete bring-up).
It's not terribly useful for an end-user, but it'll slightly speed up
suspend/resume when saving fb contents, and allow for host/ce code to
be validated.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Some of the pre-NV50 depends on SW methods to implement synchronisation
for page flips, and we want to move this setup out of common code, thus
we require the channel to have been allocation before display init.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
As part of commit cfea88a4d8 ("drm/nouveau: Start using new drm_dev
initialization helpers"), the initialization of the Nouveau DRM device
was reworked and along the way the platform driver initialization was
left incomplete. Add a call to nouveau_drm_device_init() to make sure
all of the structures are properly initialized.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Per the documentation in drm_get_pci_dev(), this function is deprecated
and shouldn't be used anymore. As it turns out, we're going to need to
stop using drm_get_pci_dev() anyway in order to allow us to turn off the
card before full system shutdowns, otherwise we'll hit race conditions
with userspace while trying to tear down the card on shutdown.
So, start using drm_dev_get() and drm_dev_put(), and just turn our
load/unload callbacks into open coded init/fini() functions.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Karol Herbst <kherbst@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
We forget to free drm in all instances of failure, and additionally also
forget to destroy the master client if the other client fails
initialization.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Karol Herbst <kherbst@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The NV_ERROR macro requires drm->client to be initialised, which it may not
be at this stage of the init process.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Currently, there's nothing in nouveau that actually cancels this work
struct. So, cancel it on suspend/unload. Otherwise, if we're unlucky
enough hpd_work might try to keep running up until the system is
suspended.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Again, this doesn't do anything. drm_kms_helper_poll_enable() will have
already been called in nouveau_display_init()
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Karol Herbst <kherbst@redhat.com>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Cc: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Since actual hotplug notifications don't get disabled until
nouveau_display_fini() is called, all this will do is cause any hotplugs
that happen between this drm_kms_helper_poll_disable() call and the
actual hotplug disablement to potentially be dropped if ACPI isn't
around to help us.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Acked-by: Karol Herbst <kherbst@redhat.com>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Cc: stable@vger.kernel.org
Cc: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Noticed this as I was skimming through, if we fail to allocate memory
for cli we'll end up returning without dropping the runtime PM ref we
got. Additionally, we'll even return the wrong return code! (ret most
likely will == 0 here, we want -ENOMEM).
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Currently nouveau doesn't actually expose the state debugfs file that's
usually provided for any modesetting driver that supports atomic, even
if nouveau is loaded with atomic=1. This is due to the fact that the
standard debugfs files that DRM creates for atomic drivers is called
when drm_get_pci_dev() is called from nouveau_drm.c. This happens well
before we've initialized the display core, which is currently
responsible for setting the DRIVER_ATOMIC cap.
So, move the atomic option into nouveau_drm.c and just add the
DRIVER_ATOMIC cap whenever it's enabled on the kernel commandline. This
shouldn't cause any actual issues, as the atomic ioctl will still fail
as expected even if the display core doesn't disable it until later in
the init sequence. This also provides the added benefit of being able to
use the state debugfs file to check the current display state even if
clients aren't allowed to modify it through anything other than the
legacy ioctls.
Additionally, disable the DRIVER_ATOMIC cap in nv04's display core, as
this was already disabled there previously.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This both uses the legacy modesetting structures in a racy manner, and
additionally also doesn't even check the right variable (enabled != the
CRTC is actually turned on for atomic).
This fixes issues on my P50 regarding the dedicated GPU not entering
runtime suspend.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: stable@vger.kernel.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Fences attached to deferred client work items now originate from channels
belonging to the client, meaning we can be certain they've been signalled
before we destroy a client.
This closes a race that could happen if the dma_fence_wait_timeout() call
didn't succeed. When the fence was later signalled, a use-after-free was
possible.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
We didn't used to be aware that runlist/engine IDs weren't the same thing,
or that there was such variability in configuration between GPUs.
By exposing this information to a client, and giving it explicit control
of which runlist it's allocating a channel on, we're able to make better
choices.
The immediate effect of this is that on GPUs where CE0 is the "GRCE", we
will now be allocating a copy engine running asynchronously to GR for BO
migrations - as intended.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Commit 5addcf0a5f ("nouveau: add runtime PM support (v0.9)") prevents
runtime suspend of the GPU if its integrated HDA controller is not bound
to a driver. The rationale appears to be that probing the HDA fails if
the GPU is in D3cold.
However we now use a device link to ensure that the GPU is runtime
resumed while the HDA controller is probed, rendering this safety
measure obsolete. Remove it.
Cc: Dave Airlie <airlied@redhat.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Peter Wu <peter@lekensteyn.nl>
Tested-by: Denis Lisov <dennis.lissov@gmail.com> # Nvidia Optimus
Tested-by: Peter Wu <peter@lekensteyn.nl> # Nvidia Optimus
Tested-by: Lukas Wunner <lukas@wunner.de> # MacBook Pro
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://patchwork.freedesktop.org/patch/msgid/77e0ab74f3377ea9b6acf8fab624acfb4f7dbeca.1520068884.git.lukas@wunner.de
Back in 2013, runtime PM for GPUs with integrated HDA controller was
introduced with commits 0d69704ae3 ("gpu/vga_switcheroo: add driver
control power feature. (v3)") and 246efa4a07 ("snd/hda: add runtime
suspend/resume on optimus support (v4)").
Briefly, the idea was that the HDA controller is forced on and off in
unison with the GPU.
The original code is mostly still in place even though it was never a
100% perfect solution: E.g. on access to the HDA controller, the GPU
is powered up via vga_switcheroo_runtime_resume_hdmi_audio() but there
are no provisions to keep it resumed until access to the HDA controller
has ceased: The GPU autosuspends after 5 seconds, rendering the HDA
controller inaccessible.
Additionally, a kludge is required when hda_intel.c probes: It has to
check whether the GPU is powered down (check_hdmi_disabled()) and defer
probing if so.
However in the meantime (in v4.10) the driver core has gained a feature
called device links which promises to solve such issues in a clean way:
It allows us to declare a dependency from the HDA controller (consumer)
to the GPU (supplier). The PM core then automagically ensures that the
GPU is runtime resumed as long as the HDA controller's ->probe hook is
executed and whenever the HDA controller is accessed.
By default, the HDA controller has a dependency on its parent, a PCIe
Root Port. Adding a device link creates another dependency on its
sibling:
PCIe Root Port
^ ^
| |
| |
HDA ===> GPU
The device link is not only used for runtime PM, it also guarantees that
on system sleep, the HDA controller suspends before the GPU and resumes
after the GPU, and on system shutdown the HDA controller's ->shutdown
hook is executed before the one of the GPU. It is a complete solution.
Using this functionality is as simple as calling device_link_add(),
which results in a dmesg entry like this:
pci 0000:01:00.1: Linked as a consumer to 0000:01:00.0
The code for the GPU-governed audio power management can thus be removed
(except where it's still needed for legacy manual power control).
The device link is added in a PCI quirk rather than in hda_intel.c.
It is therefore legal for the GPU to runtime suspend to D3cold even if
the HDA controller is not bound to a driver or if CONFIG_SND_HDA_INTEL
is not enabled, for accesses to the HDA controller will cause the GPU to
wake up regardless if they're occurring outside of hda_intel.c (think
config space readout via sysfs).
Contrary to the previous implementation, the HDA controller's power
state is now self-governed, rather than GPU-governed, whereas the GPU's
power state is no longer fully self-governed. (The HDA controller needs
to runtime suspend before the GPU can.)
It is thus crucial that runtime PM is always activated on the HDA
controller even if CONFIG_SND_HDA_POWER_SAVE_DEFAULT is set to 0 (which
is the default), lest the GPU stays awake. This is achieved by setting
the auto_runtime_pm flag on every codec and the AZX_DCAPS_PM_RUNTIME
flag on the HDA controller.
A side effect is that power consumption might be reduced if the GPU is
in use but the HDA controller is not, because the HDA controller is now
allowed to go to D3hot. Before, it was forced to stay in D0 as long as
the GPU was in use. (There is no reduction in power consumption on my
Nvidia GK107, but there might be on other chips.)
The code paths for legacy manual power control are adjusted such that
runtime PM is disabled during power off, thereby preventing the PM core
from resuming the HDA controller.
Note that the device link is not only added on vga_switcheroo capable
systems, but for *any* GPU with integrated HDA controller. The idea is
that the HDA controller streams audio via connectors located on the GPU,
so the GPU needs to be on for the HDA controller to do anything useful.
This commit implicitly fixes an unbalanced runtime PM ref upon unbind of
hda_intel.c: On ->probe, a runtime PM ref was previously released under
the condition "azx_has_pm_runtime(chip) || hda->use_vga_switcheroo", but
on ->remove a runtime PM ref was only acquired under the first of those
conditions. Thus, binding and unbinding the driver twice on a
vga_switcheroo capable system caused the runtime PM refcount to drop
below zero. The issue is resolved because the AZX_DCAPS_PM_RUNTIME flag
is now always set if use_vga_switcheroo is true.
For more information on device links please refer to:
https://www.kernel.org/doc/html/latest/driver-api/device_link.html
Documentation/driver-api/device_link.rst
Cc: Dave Airlie <airlied@redhat.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Peter Wu <peter@lekensteyn.nl>
Tested-by: Kai Heng Feng <kai.heng.feng@canonical.com> # AMD PowerXpress
Tested-by: Mike Lothian <mike@fireburn.co.uk> # AMD PowerXpress
Tested-by: Denis Lisov <dennis.lissov@gmail.com> # Nvidia Optimus
Tested-by: Peter Wu <peter@lekensteyn.nl> # Nvidia Optimus
Tested-by: Lukas Wunner <lukas@wunner.de> # MacBook Pro
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://patchwork.freedesktop.org/patch/msgid/51bd38360ff502a8c42b1ebf4405ee1d3f27118d.1520068884.git.lukas@wunner.de
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ttq9
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- skip AER driver error recovery callbacks for correctable errors
reported via ACPI APEI, as we already do for errors reported via the
native path (Tyler Baicar)
- fix DPC shared interrupt handling (Alex Williamson)
- print full DPC interrupt number (Keith Busch)
- enable DPC only if AER is available (Keith Busch)
- simplify DPC code (Bjorn Helgaas)
- calculate ASPM L1 substate parameter instead of hardcoding it (Bjorn
Helgaas)
- enable Latency Tolerance Reporting for ASPM L1 substates (Bjorn
Helgaas)
- move ASPM internal interfaces out of public header (Bjorn Helgaas)
- allow hot-removal of VGA devices (Mika Westerberg)
- speed up unplug and shutdown by assuming Thunderbolt controllers
don't support Command Completed events (Lukas Wunner)
- add AtomicOps support for GPU and Infiniband drivers (Felix Kuehling,
Jay Cornwall)
- expose "ari_enabled" in sysfs to help NIC naming (Stuart Hayes)
- clean up PCI DMA interface usage (Christoph Hellwig)
- remove PCI pool API (replaced with DMA pool) (Romain Perier)
- deprecate pci_get_bus_and_slot(), which assumed PCI domain 0 (Sinan
Kaya)
- move DT PCI code from drivers/of/ to drivers/pci/ (Rob Herring)
- add PCI-specific wrappers for dev_info(), etc (Frederick Lawler)
- remove warnings on sysfs mmap failure (Bjorn Helgaas)
- quiet ROM validation messages (Alex Deucher)
- remove redundant memory alloc failure messages (Markus Elfring)
- fill in types for compile-time VGA and other I/O port resources
(Bjorn Helgaas)
- make "pci=pcie_scan_all" work for Root Ports as well as Downstream
Ports to help AmigaOne X1000 (Bjorn Helgaas)
- add SPDX tags to all PCI files (Bjorn Helgaas)
- quirk Marvell 9128 DMA aliases (Alex Williamson)
- quirk broken INTx disable on Ceton InfiniTV4 (Bjorn Helgaas)
- fix CONFIG_PCI=n build by adding dummy pci_irqd_intx_xlate() (Niklas
Cassel)
- use DMA API to get MSI address for DesignWare IP (Niklas Cassel)
- fix endpoint-mode DMA mask configuration (Kishon Vijay Abraham I)
- fix ARTPEC-6 incorrect IS_ERR() usage (Wei Yongjun)
- add support for ARTPEC-7 SoC (Niklas Cassel)
- add endpoint-mode support for ARTPEC (Niklas Cassel)
- add Cadence PCIe host and endpoint controller driver (Cyrille
Pitchen)
- handle multiple INTx status bits being set in dra7xx (Vignesh R)
- translate dra7xx hwirq range to fix INTD handling (Vignesh R)
- remove deprecated Exynos PHY initialization code (Jaehoon Chung)
- fix MSI erratum workaround for HiSilicon Hip06/Hip07 (Dongdong Liu)
- fix NULL pointer dereference in iProc BCMA driver (Ray Jui)
- fix Keystone interrupt-controller-node lookup (Johan Hovold)
- constify qcom driver structures (Julia Lawall)
- rework Tegra config space mapping to increase space available for
endpoints (Vidya Sagar)
- simplify Tegra driver by using bus->sysdata (Manikanta Maddireddy)
- remove PCI_REASSIGN_ALL_BUS usage on Tegra (Manikanta Maddireddy)
- add support for Global Fabric Manager Server (GFMS) event to
Microsemi Switchtec switch driver (Logan Gunthorpe)
- add IDs for Switchtec PSX 24xG3 and PSX 48xG3 (Kelvin Cao)
* tag 'pci-v4.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (140 commits)
PCI: cadence: Add EndPoint Controller driver for Cadence PCIe controller
dt-bindings: PCI: cadence: Add DT bindings for Cadence PCIe endpoint controller
PCI: endpoint: Fix EPF device name to support multi-function devices
PCI: endpoint: Add the function number as argument to EPC ops
PCI: cadence: Add host driver for Cadence PCIe controller
dt-bindings: PCI: cadence: Add DT bindings for Cadence PCIe host controller
PCI: Add vendor ID for Cadence
PCI: Add generic function to probe PCI host controllers
PCI: generic: fix missing call of pci_free_resource_list()
PCI: OF: Add generic function to parse and allocate PCI resources
PCI: Regroup all PCI related entries into drivers/pci/Makefile
PCI/DPC: Reformat DPC register definitions
PCI/DPC: Add and use DPC Status register field definitions
PCI/DPC: Squash dpc_rp_pio_get_info() into dpc_process_rp_pio_error()
PCI/DPC: Remove unnecessary RP PIO register structs
PCI/DPC: Push dpc->rp_pio_status assignment into dpc_rp_pio_get_info()
PCI/DPC: Squash dpc_rp_pio_print_error() into dpc_rp_pio_get_info()
PCI/DPC: Make RP PIO log size check more generic
PCI/DPC: Rename local "status" to "dpc_status"
PCI/DPC: Squash dpc_rp_pio_print_tlp_header() into dpc_rp_pio_print_error()
...
pci_get_bus_and_slot() is restrictive such that it assumes domain=0 as
where a PCI device is present. This restricts the device drivers to be
reused for other domain numbers.
Getting ready to remove pci_get_bus_and_slot() function in favor of
pci_get_domain_bus_and_slot().
Replace pci_get_bus_and_slot() with pci_get_domain_bus_and_slot()
and extract the domain number from
1. struct pci_dev
2. struct pci_dev through drm_device->pdev
3. struct pci_dev through fb->subdev->drm_device->pdev
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
TTM memory allocations will be hanging off the DRM's client, but the
locking needed to do so gets really tricky with all the other use of
the DRM's object tree.
To solve this, we make the normal DRM client a child of a new master,
where the memory allocations will be done from instead.
This also solves a potential race with client creation.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The magic switching between proper pci driver and shadow-attach isn't
useful anymore since there's no ums+kms drivers left. Let's split this
up properly, calling pci_register_driver for kms drivers and renaming
the shadow-attach init to drm_legacy_pci_init/exit.
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170524145212.27837-6-daniel.vetter@ffwll.ch
There is a prototype for this function in the header, but the function
itself lacks a 'void' in the argument list, causing a harmless warning
when building with 'make W=1':
drivers/gpu/drm/nouveau/nouveau_drm.c: In function 'nouveau_pmops_runtime':
drivers/gpu/drm/nouveau/nouveau_drm.c:730:1: error: old-style function definition [-Werror=old-style-definition]
Fixes: 321f5c5f2c ("drm/nouveau: replace multiple open-coded runpm support checks with function")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZPdbLAAoJEHm+PkMAQRiGx4wH/1nCjfnl6fE8oJ24/1gEAOUh
biFdqJkYZmlLYHVtYfLm4Ueg4adJdg0wx6qM/4RaAzmQVvLfDV34bc1qBf1+P95G
kVF+osWyXrZo5cTwkwapHW/KNu4VJwAx2D1wrlxKDVG5AOrULH1pYOYGOpApEkZU
4N+q5+M0ce0GJpqtUZX+UnI33ygjdDbBxXoFKsr24B7eA0ouGbAJ7dC88WcaETL+
2/7tT01SvDMo0jBSV0WIqlgXwZ5gp3yPGnklC3F4159Yze6VFrzHMKS/UpPF8o8E
W9EbuzwxsKyXUifX2GY348L1f+47glen/1sedbuKnFhP6E9aqUQQJXvEO7ueQl4=
=m2Gx
-----END PGP SIGNATURE-----
BackMerge tag 'v4.12-rc5' into drm-next
Linux 4.12-rc5 for nouveau fixes
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZK2lrAAoJEHm+PkMAQRiGm3AH/13F1DlIk05aSXHoDr/idIpR
GMHmk3YF+EuFjsL463Sh6s/SSWmz0Lda8euaoB4wCWvQFX2ZjTE+aOd79XlRiZJQ
OTtLkV9I41eXIJUpEOHia7xZiCsbw+usqcHrm1aBoSh5KKV2iQmEOrnJdibqJVOF
eXUMphNK/zFtAd2bKtQSxkaBnOOqsQUgVQSkr2K9rSg25l0KokFC6c5K5IjLn4x9
QgDY4wmMvHrDz0CtpoqlNM4XqbsDJVrFeZGfg6hlMqSRDeXeg4h3Ol0VfIT496RP
QBdrDb6hWO+HKt9B0M+7Q+8a/Fsw+5dtpqv1W/Wlr0i4CS6euU8NChAmrpkrqGo=
=m5ba
-----END PGP SIGNATURE-----
Backmerge tag 'v4.12-rc3' into drm-next
Linux 4.12-rc3
Daniel has requested this for some drm-intel-next work.
Jérôme Glisse