An error message is printed for resources of type 19, which is a valid
supported resource type. The Firmware Test Suite tool (fwts) reports
this as a test failure. This change fixes the false test failures
for ASL that use type 19 (ACPI_RESOURCE_TYPE_SERIAL_BUS) resources.
Signed-off-by: Harb Abdulhamid <harba@codeaurora.org>
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This is preparation for using kstrdup_const to initialize that member.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
use unsigned int for port, irq, dma and mem used for pnp_get_resource()
This fixes gcc warnings of type "conversion to unsigned int
from int may change the sign of the result"
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
acpi_resource_extented_irq variables are all u8.
Use that type for triggering, polarity and shareable.
This fixes gcc warnings of type
"conversion to u8 from int may alter its value"
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
pnpacpi_add_device() calls acpi_bind_one() on an already registered
device, which is a mistake, but it can initialize the ACPI companion
field of the struct device to be registered using ACPI_COMPANION_SET()
instead, so make it do that.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Change function acpi_dev_resource_address_space() and
acpi_dev_resource_ext_address_space() to return address space
translation offset.
It's based on a patch from Yinghai Lu <yinghai@kernel.org>.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
struct acpi_resource_address and struct acpi_resource_extended_address64 share substracts
just at different offsets. To unify the parsing functions, OSPMs like Linux
need a new ACPI_ADDRESS64_ATTRIBUTE as their substructs, so they can
extract the shared data.
This patch also synchronizes the structure changes to the Linux kernel.
The usages are searched by matching the following keywords:
1. acpi_resource_address
2. acpi_resource_extended_address
3. ACPI_RESOURCE_TYPE_ADDRESS
4. ACPI_RESOURCE_TYPE_EXTENDED_ADDRESS
And we found and fixed the usages in the following files:
arch/ia64/kernel/acpi-ext.c
arch/ia64/pci/pci.c
arch/x86/pci/acpi.c
arch/x86/pci/mmconfig-shared.c
drivers/xen/xen-acpi-memhotplug.c
drivers/acpi/acpi_memhotplug.c
drivers/acpi/pci_root.c
drivers/acpi/resource.c
drivers/char/hpet.c
drivers/pnp/pnpacpi/rsparser.c
drivers/hv/vmbus_drv.c
Build tests are passed with defconfig/allnoconfig/allyesconfig and
defconfig+CONFIG_ACPI=n.
Original-by: Thomas Gleixner <tglx@linutronix.de>
Original-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The ACPI_HANDLE() macro evaluates ACPI_COMPANION() internally to
return the handle of the device's ACPI companion, so it is much
more straightforward and efficient to use ACPI_COMPANION()
directly to obtain the device's ACPI companion object instead of
using ACPI_HANDLE() and acpi_bus_get_device() on the returned
handle for the same thing.
Do that in several places in the ACPI PNP core code.
Also use acpi_device_set_power() and acpi_device_power_manageable()
instead of acpi_bus_set_power() and acpi_bus_power_manageable(),
respectively, because the former two are more efficient if the
ACPI device object is already available.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
PNPACPI uses acpi_bus_type to do ACPI binding for the PNPACPI devices.
This is overkill because PNPACPI code already knows which ACPI
device object to bind during PNPACPI device enumeration.
This patch removes acpi_pnp_bus and does the binding by invoking
acpi_bind_one() directly after device enumerated.
This also fixes a bug in the previous code that some PNPACPI devices failed
to be bound because
1. the ACPI device _HID is not pnpid, e.g. "MSFT0001", but its _CID is,
e.g. "PNP0303", thus ACPI _CID is used as the pnp device device id.
2. device is bound only if the pnp device id matches the ACPI device _HID.
Tested-by: Prigent Christophe <christophe.prigent@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPI can be used to enumerate PNP devices, but the code does not
handle this in the right way currently. Namely, if an ACPI device
object
1. Has a _CRS method,
2. Has an identification of
"three capital characters followed by four hex digits",
3. Is not in the excluded IDs list,
it will be enumerated to PNP bus (that is, a PNP device object will
be create for it). This means that, actually, the PNP bus type is
used as the default bus type for enumerating _HID devices in ACPI.
However, more and more _HID devices need to be enumerated to the
platform bus instead (that is, platform device objects need to be
created for them). As a result, the device ID list in acpi_platform.c
is used to enforce creating platform device objects rather than PNP
device objects for matching devices. That list has been continuously
growing recently, unfortunately, and it is pretty much guaranteed to
grow even more in the future.
To address that problem it is better to enumerate _HID devices
as platform devices by default. To this end, change the way of
enumerating PNP devices by adding a PNP ACPI scan handler that
will use a device ID list to create PNP devices for the ACPI
device objects whose device IDs are present in that list.
The initial device ID list in the PNP ACPI scan handler contains
all of the pnp_device_id strings from all the existing PNP drivers,
so this change should be transparent to the PNP core and all of the
PNP drivers. Still, in the future it should be possible to reduce
its size by converting PNP drivers that need not be PNP for any
technical reasons into platform drivers.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
[rjw: Rewrote the changelog, modified the PNP ACPI scan handler code]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The ACPI PNP subsystem returns errors from pnpacpi_set_resources()
and pnpacpi_disable_resources() if the _SRS or _DIS methods are not
present, respectively, but it should not do that, because those
methods are optional. For this reason, modify pnpacpi_set_resources()
and pnpacpi_disable_resources(), respectively, to ignore missing _SRS
or _DIS.
This problem has been uncovered by commit 202317a573 (ACPI / scan:
Add acpi_device objects for all device nodes in the namespace) and
manifested itself by causing serial port suspend to fail on some
systems.
Fixes: 202317a573 (ACPI / scan: Add acpi_device objects for all device nodes in the namespace)
References: https://bugzilla.kernel.org/show_bug.cgi?id=74371
Reported-by: wxg4net <wxg4net@gmail.com>
Reported-and-tested-by: <nonproffessional@gmail.com>
Cc: 3.14+ <stable@vger.kernel.org> # 3.14+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Before commit b355cee88e (ACPI / resources: ignore invalid ACPI
device resources), if acpi_dev_resource_memory()/acpi_dev_resource_io()
returns false, it means the the resource is not a memeory/IO resource.
But after commit b355cee88e, those functions return false if the
given memory/IO resource entry is invalid (the length of the resource
is zero).
This breaks pnpacpi_allocated_resource(), because it now recognizes
the invalid memory/io resources as resources of unknown type. Thus
users see confusing warning messages on machines with zero length
ACPI memory/IO resources.
Fix the problem by rearranging pnpacpi_allocated_resource() so that
it calls acpi_dev_resource_memory() for memory type and IO type
resources only, respectively.
Fixes: b355cee88e (ACPI / resources: ignore invalid ACPI device resources)
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Reported-and-tested-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Reported-and-tested-by: Julian Wollrath <jwollrath@web.de>
Reported-and-tested-by: Paul Bolle <pebolle@tiscali.nl>
[rjw: Changelog]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* pnp:
PNPBIOS: check return value of pnp_add_device()
PNP: Mark the function pnp_build_option() as static in resource.c
PNP / card: add missing put_device() call
PNPACPI: check return value of pnp_add_device()
pnp_add_device() may fail so we need to handle errors and avoid leaking
memory. Also, do not use ACPI-specific return codes (AE_OK) but rather
standard one (0).
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Replace the .find_device function pointer in struct acpi_bus_type
with a new one, .find_companion, that is supposed to point to a
function returning struct acpi_device pointer (instead of an int)
and takes one argument (instead of two). This way the role of
this callback is more clear and the implementation of it can
be more straightforward.
Update all of the users of struct acpi_bus_type (PCI, PNP/ACPI and
USB) to reflect the structure change.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Lan Tianyu <tianyu.lan@intel.com> # for USB/ACPI
Replace direct inclusions of <acpi/acpi.h>, <acpi/acpi_bus.h> and
<acpi/acpi_drivers.h>, which are incorrect, with <linux/acpi.h>
inclusions and remove some inclusions of those files that aren't
necessary.
First of all, <acpi/acpi.h>, <acpi/acpi_bus.h> and <acpi/acpi_drivers.h>
should not be included directly from any files that are built for
CONFIG_ACPI unset, because that generally leads to build warnings about
undefined symbols in !CONFIG_ACPI builds. For CONFIG_ACPI set,
<linux/acpi.h> includes those files and for CONFIG_ACPI unset it
provides stub ACPI symbols to be used in that case.
Second, there are ordering dependencies between those files that always
have to be met. Namely, it is required that <acpi/acpi_bus.h> be included
prior to <acpi/acpi_drivers.h> so that the acpi_pci_root declarations the
latter depends on are always there. And <acpi/acpi.h> which provides
basic ACPICA type declarations should always be included prior to any other
ACPI headers in CONFIG_ACPI builds. That also is taken care of including
<linux/acpi.h> as appropriate.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> (drivers/pci stuff)
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> (Xen stuff)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since DEVICE_ACPI_HANDLE() is now literally identical to
ACPI_HANDLE(), replace it with the latter everywhere and drop its
definition from include/acpi.h.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
acpi_has_method() is a new ACPI API introduced to check
the existence of an ACPI control method.
It can be used to replace acpi_get_handle() in the case that
1. the calling function doesn't need the ACPI handle of the control method.
and
2. the calling function doesn't care the reason why the method is unavailable.
Convert acpi_get_handle() to acpi_has_method()
in drivers/pnp/pnpacpi/core.c in this patch.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
CC: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There are several places in the tree where ACPI_STATE_D3 is used
instead of ACPI_STATE_D3_COLD which should be used instead for
clarity. Modify them all to use ACPI_STATE_D3_COLD as appropriate.
[The definition of ACPI_STATE_D3 itself cannot go away at this point
as it is part of ACPICA.]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Aaron Lu <aaron.lu@intel.com>
Set temporary variable as 0 to avoid garbage string output from
/proc/iomem after register resources and reset to PNP dev name
later.
Signed-off-by: Liu ShuoX <shuox.liu@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Found with a network device in QEMU/KVM guest not working anymore.
Bisected to commit c13085e5
ACPICA: Resource Mgr: Prevent infinite loops in resource walks
That commit will check acpi_resource length strictly which causes
acpi_set_current_resources to return failure and IRQ for PCI
devices is not set properly.
Set length for all those TYPE_END_TAG acpi_resources.
[rjw: Changelog]
Bisected-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
USB uses the .find_bridge() callback from struct acpi_bus_type
incorrectly, because as a result of the way it is used by USB every
device in the system that doesn't have a bus type or parent is
passed to usb_acpi_find_device() for inspection.
What USB actually needs, though, is to call usb_acpi_find_device()
for USB ports that don't have a bus type defined, but have
usb_port_device_type as their device type, as well as for USB
devices.
To fix that replace the struct bus_type pointer in struct
acpi_bus_type used for matching devices to specific subsystems
with a .match() callback to be used for this purpose and update
the users of struct acpi_bus_type, including USB, accordingly.
Define the .match() callback routine for USB, usb_acpi_bus_match(),
in such a way that it will cover both USB devices and USB ports
and remove the now redundant .find_bridge() callback pointer from
usb_acpi_bus.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
acpi_bus_get_device() returns int not acpi_status.
The patch change not to apply ACPI_FAILURE() to the return value of
acpi_bus_get_device().
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* acpi-general:
pnpacpi: fix incorrect TEST_ALPHA() test
ACPI / video: ignore BIOS initial backlight value for HP Folio 13-2000
ACPI : do not use Lid and Sleep button for S5 wakeup
TEST_ALPHA() is broken and always returns 0.
[akpm@linux-foundation.org: return false for '@' as well, per Bjorn]
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* acpi-general:
ACPI / PNP: Do not crash due to stale pointer use during system resume
ACPI / video: Add "Asus UL30VT" to ACPI video detect blacklist
ACPI: do acpisleep dmi check when CONFIG_ACPI_SLEEP is set
During resume from system suspend the 'data' field of
struct pnp_dev in pnpacpi_set_resources() may be a stale pointer,
due to removal of the associated ACPI device node object in the
previous suspend-resume cycle. This happens, for example, if a
dockable machine is booted in the docking station and then suspended
and resumed and suspended again. If that happens,
pnpacpi_build_resource_template() called from pnpacpi_set_resources()
attempts to use that pointer and crashes.
However, pnpacpi_set_resources() actually checks the device's ACPI
handle, attempts to find the ACPI device node object attached to it
and returns an error code if that fails, so in fact it knows what the
correct value of dev->data should be. Use this observation to update
dev->data with the correct value if necessary and dump a call trace
if that's the case (once).
We still need to fix the root cause of this issue, but preventing
systems from crashing because of it is an improvement too.
Reported-and-tested-by: Zdenek Kabelac <zdenek.kabelac@gmail.com>
References: https://bugzilla.kernel.org/show_bug.cgi?id=51071
Cc: <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Make pnpacpi_add_device() ignore ACPI device nodes already associated
with struct device objects representing physical devices.
In particular, this will prevent PNP device objects from being
created for ACPI device nodes already associated with platform
devices.
This change was originally proposed by Mika Westerberg.
[rjw: Modified the subject and changelog.]
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Move some code used for parsing ACPI device resources from the PNP
subsystem to the ACPI core, so that other bus types (platform, SPI,
I2C) can use the same routines for parsing resources in a consistent
way, without duplicating code.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
A USB port's position and connectability can't be identified on some boards
via USB hub registers. ACPI _UPC and _PLD can help to resolve this issue
and so it is necessary to bind USB with ACPI. This patch is to allow ACPI
binding with USB-3.0 hub.
Current ACPI only can bind one struct-device to one ACPI device node.
This can not work with USB-3.0 hub, because the USB-3.0 hub has two logical
devices. Each works for USB-2.0 and USB-3.0 devices. In the Linux USB subsystem,
those two logical hubs are treated as two seperate devices that have two struct
devices. But in the ACPI DSDT, these two logical hubs share one ACPI device
node. So there is a requirement to bind multi struct-devices to one ACPI
device node. This patch is to resolve such problem.
Following is the ACPI device nodes' description under xhci hcd.
Device (XHC)
Device (RHUB)
Device (HSP1)
Device (HSP2)
Device (HSP3)
Device (HSP4)
Device (SSP1)
Device (SSP2)
Device (SSP3)
Device (SSP4)
Topology in the Linux
device XHC
USB-2.0 logical hub USB-3.0 logical hub
HSP1 SSP1
HSP2 SSP2
HSP3 SSP3
HSP4 SSP4
This patch also modifies the output of /proc/acpi/wakeup. One ACPI node
can be associated with multiple devices:
XHC S4 *enabled pci:0000:00:14.0
RHUB S0 disabled usb:usb1
disabled usb:usb2
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Lower device sleep state can save more power, but has more exit
latency too. Sometimes, to satisfy some power QoS and other
requirement, we need to constrain the lowest device sleep state.
In this patch, a parameter to specify lowest allowed state for
acpi_pm_device_sleep_state is added. So that the caller can enforce
the constraint via the parameter.
This is needed by PCIe D3cold support, where the lowest power state
allowed may be D3_HOT instead of default D3_COLD.
CC: Len Brown <lenb@kernel.org>
CC: linux-acpi@vger.kernel.org
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
During testing pci root bus removal, found some root bus bridge is not freed.
If booting with pnpacpi=off, those hostbridge could be freed without problem.
It turns out that some devices reference are not released during acpi_pnp_match.
that match should not hold one device ref during every calling.
Add pu_device calling before returning.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Len Brown <len.brown@intel.com>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
cpuidle: Single/Global registration of idle states
cpuidle: Split cpuidle_state structure and move per-cpu statistics fields
cpuidle: Remove CPUIDLE_FLAG_IGNORE and dev->prepare()
cpuidle: Move dev->last_residency update to driver enter routine; remove dev->last_state
ACPI: Fix CONFIG_ACPI_DOCK=n compiler warning
ACPI: Export FADT pm_profile integer value to userspace
thermal: Prevent polling from happening during system suspend
ACPI: Drop ACPI_NO_HARDWARE_INIT
ACPI atomicio: Convert width in bits to bytes in __acpi_ioremap_fast()
PNPACPI: Simplify disabled resource registration
ACPI: Fix possible recursive locking in hwregs.c
ACPI: use kstrdup()
mrst pmu: update comment
tools/power turbostat: less verbose debugging
The attached patch simplifies 29df8d8f87. As
the "pnp_xxx" structs are not designed to cope with IORESOURCE_DISABLED, and
hence no code can test for this value, setting this value is actually a "no op"
and can be skipped altogether. It is sufficient to remove the checks for
"empty" resources and continue processing.
The patch is applied against 3.1.
Signed-off-by: Witold Szczeponik <Witold.Szczeponik@gmx.net>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Len Brown <len.brown@intel.com>
These macros are no longer in module.h and module.h is no longer
present everywhere. Call out export.h for the users who are
making use of these macros.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
* Merge akpm patch series: (122 commits)
drivers/connector/cn_proc.c: remove unused local
Documentation/SubmitChecklist: add RCU debug config options
reiserfs: use hweight_long()
reiserfs: use proper little-endian bitops
pnpacpi: register disabled resources
drivers/rtc/rtc-tegra.c: properly initialize spinlock
drivers/rtc/rtc-twl.c: check return value of twl_rtc_write_u8() in twl_rtc_set_time()
drivers/rtc: add support for Qualcomm PMIC8xxx RTC
drivers/rtc/rtc-s3c.c: support clock gating
drivers/rtc/rtc-mpc5121.c: add support for RTC on MPC5200
init: skip calibration delay if previously done
misc/eeprom: add eeprom access driver for digsy_mtc board
misc/eeprom: add driver for microwire 93xx46 EEPROMs
checkpatch.pl: update $logFunctions
checkpatch: make utf-8 test --strict
checkpatch.pl: add ability to ignore various messages
checkpatch: add a "prefer __aligned" check
checkpatch: validate signature styles and To: and Cc: lines
checkpatch: add __rcu as a sparse modifier
checkpatch: suggest using min_t or max_t
...
Did this as a merge because of (trivial) conflicts in
- Documentation/feature-removal-schedule.txt
- arch/xtensa/include/asm/uaccess.h
that were just easier to fix up in the merge than in the patch series.
When parsing PnP ACPI resource structures, it may happen that some of
the resources are disabled (in which case "the size" of the resource
equals zero).
The current solution is to skip these resources completely - with the
unfortunate side effect that they are not registered despite the fact
that they exist, after all. (The downside of this approach is that
these resources cannot be used as templates for setting the actual
device's resources because they are missing from the template.) The
kernel's APM implementation does not suffer from this problem and
registers all resources regardless of "their size".
This patch fixes a problem with (at least) the vintage IBM ThinkPad 600E
(and most likely also with the 600, 600X, and 770X which have a very
similar layout) where some of its PnP devices support options where
either an IRQ, a DMA, or an IO port is disabled. Without this patch,
the devices can not be configured using the
"/sys/bus/pnp/devices/*/resources" interface.
The manipulation of these resources is important because the 600E has
very demanding requirements. For instance, the number of IRQs is not
sufficient to support all devices of the 600E. Fortunately, some of the
devices, like the sound card's MPU-401 UART, can be configured to not
use any IRQ, hence freeing an IRQ for a device that requires one.
(Still, the device's "ResourceTemplate" requires an IRQ resource
descriptor which cannot be created if the resource has not been
registered in the first place.)
As an example, the dependent sets of the 600E's CSC0103 device (the
MPU-401 UART) are listed, with the patch applied, as:
Dependent: 00 - Priority preferred
port 0x300-0x330, align 0xf, size 0x4, 16-bit address decoding
irq <none> High-Edge
Dependent: 01 - Priority acceptable
port 0x300-0x330, align 0xf, size 0x4, 16-bit address decoding
irq 5,7,2/9,10,11,15 High-Edge
(The same result is obtained when PNPBIOS is used instead of PnP ACPI.)
Without the patch, the IRQ resource in the preferred option is not
listed at all:
Dependent: 00 - Priority preferred
port 0x300-0x330, align 0xf, size 0x4, 16-bit address decoding
Dependent: 01 - Priority acceptable
port 0x300-0x330, align 0xf, size 0x4, 16-bit address decoding
irq 5,7,2/9,10,11,15 High-Edge
And in fact, the 600E's DSDT lists the disabled IRQ as an option, as can
be seen from the following excerpt from the DSDT:
Name (_PRS, ResourceTemplate ()
{
StartDependentFn (0x00, 0x00)
{
IO (Decode16, 0x0300, 0x0330, 0x10, 0x04)
IRQNoFlags () {}
}
StartDependentFn (0x01, 0x00)
{
IO (Decode16, 0x0300, 0x0330, 0x10, 0x04)
IRQNoFlags () {5,7,9,10,11,15}
}
EndDependentFn ()
})
With this patch applied, a user space program - or maybe even the kernel
- can allocate all devices' resources optimally. For the 600E, this
means to find optimal resources for (at least) the serial port, the
parallel port, the infrared port, the MWAVE modem, the sound card, and
the MPU-401 UART.
The patch applies the idea to register disabled resources to all types
of resources, not just to IRQs, DMAs, and IO ports. At the same time,
it mimics the behavior of the "pnp_assign_xxx" functions from
"drivers/pnp/manager.c" where resources with "no size" are considered
disabled.
No regressions were observed on hardware that does not require this
patch.
The patch is applied against 2.6.39.
NB: The kernel's current PnP interface does not allow for disabling individual
resources using the "/sys/bus/pnp/devices/$device/resources" file. Assuming
this could be done, a device could be configured to use a disabled resource
using a simple series of calls:
echo disable > /sys/bus/pnp/devices/$device/resources
echo clear > /sys/bus/pnp/devices/$device/resources
echo set irq disabled > /sys/bus/pnp/devices/$device/resources
echo fill > /sys/bus/pnp/devices/$device/resources
echo activate > /sys/bus/pnp/devices/$device/resources
This patch addresses only the parsing of PnP ACPI devices.
ChangeLog (v1 -> v2):
- extend patch description
- fix typo in patch itself
Signed-off-by: Witold Szczeponik <Witold.Szczeponik@gmx.net>
Cc: Len Brown <lenb@kernel.org>
Cc: Adam Belay <abelay@mit.edu>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Several fixes as well where the +1 was missing.
Done via coccinelle scripts like:
@@
struct resource *ptr;
@@
- ptr->end - ptr->start + 1
+ resource_size(ptr)
and some grep and typing.
Mostly uncompiled, no cross-compilers.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The PNP ACPI driver squirrels the ACPI handles of PNP devices' ACPI
companions, but this isn't correct, because those handles should be
accessed using the DEVICE_ACPI_HANDLE() macro operating on struct
device objects.
Using DEVICE_ACPI_HANDLE() in the PNP ACPI driver instead of the
driver's own copies of the ACPI handles allows us to avoid a problem
with docking stations where a machine docked before suspend to RAM
and undocked while suspended crashes during the subsequent resume (in
that case the ACPI companion of the PNP device in question doesn't
exist any more while the device is being resumed). It also allows us
to avoid the problem where suspend to RAM fails when the machine was
undocked while suspended before (again, the ACPI companion of the PNP
device is not present any more while it is being suspended).
This change doesn't fix all of the the PNP ACPI driver's problems
with PNP devices in docking stations (generally speaking, the driver
has no idea that devices can come and go and doesn't even attempt to
handle such events), but at least it makes suspend work for the
users of docking stations who don't use the PNP devices located in
there.
References: https://bugzilla.kernel.org/show_bug.cgi?id=15100
Reported-and-tested-by: Toralf Förster <toralf.foerster@gmx.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This is cleanup mostly, nothing urgent.
I came up with it when looking at dynamic debug which can
enable pr_debug messages at runtime or boot param
for a specific module.
Advantages:
- Any pnp code can make use of the moduleparam.h interface, the modules
will show up as pnp.param.
- Passing pnp.ddebug as kernel boot param will enable all pnp debug messages
with my previous patch and CONFIG_DYNAMIC_DEBUG enabled.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
If primary ID (HID) is invalid try locating first valid ID on compatible
ID list before giving up.
This helps, for example, to recognize i8042 AUX port on Sony Vaio VPCZ1
which uses SNYSYN0003 as HID. Without the patch users are forced to
boot with i8042.nopnp to make use of their touchpads.
Tested-by: Jan-Hendrik Zab <jan@jhz.name>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch (as1354) adds remote-wakeup support to the pnpacpi driver.
The new can_wakeup method also allows other PNP protocol drivers
(pnpbios or iaspnp) to add wakeup support, but I don't know enough
about how they work to actually do it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
ACPI _CRS Address Space Descriptors have _MIN, _MAX, and _LEN. Linux has
been computing Address Spaces as [_MIN to _MIN + _LEN - 1]. Based on the
tests in the bug reports below, Windows apparently uses [_MIN to _MAX].
Per spec (ACPI 4.0, Table 6-40), for _CRS fixed-size, fixed location
descriptors, "_LEN must be (_MAX - _MIN + 1)", and when that's true, it
doesn't matter which way we compute the end. But of course, there are
BIOSes that don't follow this rule, and we're better off if Linux handles
those exceptions the same way as Windows.
This patch makes Linux use [_MIN to _MAX], as Windows seems to do. This
effectively reverts 3162b6f0c5 and replaces it with simpler code.
https://bugzilla.kernel.org/show_bug.cgi?id=14337 (round)
https://bugzilla.kernel.org/show_bug.cgi?id=15480 (truncate)
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The ACPI spec (sec 6.4.3.5 in v4.0) requires that for Address Space Resource
Descriptors, _LEN <= _MAX - _MIN + 1 in all cases, but there are BIOSes that
violate this. We experimentally determined that Windows truncates the
resource so it doesn't extend past _MAX, so let's do the same thing in
Linux.
http://bugzilla.kernel.org/show_bug.cgi?id=15480
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Harb Abdulhamid