The prima2 platform advertises needing no mach/gpio.h header file,
but its pinctrl driver now has a sirfsoc_gpio_set_pull function
that uses constants defined in arch/arm/mach-prima2/include/mach/gpio.h,
which fails to build.
Fortunately, the sirfsoc_gpio_set_pull is not used anywhere in the
kernel, so we can safely remove it. Any out of tree drivers using
it will have to be converted to use proper pinctrl functions to
do the same.
Without this patch, building prima2_defconfig results in:
drivers/pinctrl/pinctrl-sirf.c: In function 'sirfsoc_gpio_set_pull':
drivers/pinctrl/pinctrl-sirf.c:1331:7: error: 'SIRFSOC_GPIO_PULL_NONE' undeclared (first use in this function)
drivers/pinctrl/pinctrl-sirf.c:1331:7: note: each undeclared identifier is reported only once for each function it appears in
drivers/pinctrl/pinctrl-sirf.c:1334:7: error: 'SIRFSOC_GPIO_PULL_UP' undeclared (first use in this function)
drivers/pinctrl/pinctrl-sirf.c:1338:7: error: 'SIRFSOC_GPIO_PULL_DOWN' undeclared (first use in this function)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Helper function for updating nand platform data has been
added the capability to take timing structure arguement.
Usage of omap_nand_flash_init() has been replaced by modifed
one, omap_nand_flash_init was doing things similar to
board_nand_init except that NAND CS# were being acquired
based on bootloader setting. As CS# is hardwired for a given
board, acquiring gpmc CS# has been removed, and updated with
the value on board.
NAND CS# used in beagle board & omap3evm was found to be CS0.
Thomas Weber <thomas.weber.linux@googlemail.com> reported
that value of devkit8000 to be CS0. Overo board was found
to be using CS0 based on u-boot, while google grep says
omap3touchbook too has CS0.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Reviewed-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
a2a47ca366
(ARM: __io abuse cleanup) cleanuped __io() -> IOMEM(),
but armadillo800eva was a outside of a target,
since "merge window" timing issue.
This patch cleanup it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Pull module signing support from Rusty Russell:
"module signing is the highlight, but it's an all-over David Howells frenzy..."
Hmm "Magrathea: Glacier signing key". Somebody has been reading too much HHGTTG.
* 'modules-next' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (37 commits)
X.509: Fix indefinite length element skip error handling
X.509: Convert some printk calls to pr_devel
asymmetric keys: fix printk format warning
MODSIGN: Fix 32-bit overflow in X.509 certificate validity date checking
MODSIGN: Make mrproper should remove generated files.
MODSIGN: Use utf8 strings in signer's name in autogenerated X.509 certs
MODSIGN: Use the same digest for the autogen key sig as for the module sig
MODSIGN: Sign modules during the build process
MODSIGN: Provide a script for generating a key ID from an X.509 cert
MODSIGN: Implement module signature checking
MODSIGN: Provide module signing public keys to the kernel
MODSIGN: Automatically generate module signing keys if missing
MODSIGN: Provide Kconfig options
MODSIGN: Provide gitignore and make clean rules for extra files
MODSIGN: Add FIPS policy
module: signature checking hook
X.509: Add a crypto key parser for binary (DER) X.509 certificates
MPILIB: Provide a function to read raw data into an MPI
X.509: Add an ASN.1 decoder
X.509: Add simple ASN.1 grammar compiler
...
Pull ARM update from Russell King:
"This is the final round of stuff for ARM, left until the end of the
merge window to reduce the number of conflicts. This set contains the
ARM part of David Howells UAPI changes, and a fix to the ordering of
'select' statements in ARM Kconfig files (see the appropriate commit
for why this happened - thanks to Andrew Morton for pointing out the
problem.)
I've left this as long as I dare for this window to avoid conflicts,
and I regenerated the config patch yesterday, posting it to our
mailing list for review and testing. I have several acks which
include successful test reports for it.
However, today I notice we've got new conflicts with previously unseen
code... though that conflict should be trivial (it's my changes vs a
one liner.)"
* 'late-for-linus' of git://git.linaro.org/people/rmk/linux-arm:
ARM: config: make sure that platforms are ordered by option string
ARM: config: sort select statements alphanumerically
UAPI: (Scripted) Disintegrate arch/arm/include/asm
Fix up fairly conflict in arch/arm/Kconfig (the select re-organization
vs recent addition of GENERIC_KERNEL_EXECVE)
The large platform selection choice should be sorted by option string
so it's easy to find the platform you're looking for. Fix the few
options which are out of this order.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As suggested by Andrew Morton:
This is a pet peeve of mine. Any time there's a long list of items
(header file inclusions, kconfig entries, array initalisers, etc) and
someone wants to add a new item, they *always* go and stick it at the
end of the list.
Guys, don't do this. Either put the new item into a randomly-chosen
position or, probably better, alphanumerically sort the list.
lets sort all our select statements alphanumerically. This commit was
created by the following perl:
while (<>) {
while (/\\\s*$/) {
$_ .= <>;
}
undef %selects if /^\s*config\s+/;
if (/^\s+select\s+(\w+).*/) {
if (defined($selects{$1})) {
if ($selects{$1} eq $_) {
print STDERR "Warning: removing duplicated $1 entry\n";
} else {
print STDERR "Error: $1 differently selected\n".
"\tOld: $selects{$1}\n".
"\tNew: $_\n";
exit 1;
}
}
$selects{$1} = $_;
next;
}
if (%selects and (/^\s*$/ or /^\s+help/ or /^\s+---help---/ or
/^endif/ or /^endchoice/)) {
foreach $k (sort (keys %selects)) {
print "$selects{$k}";
}
undef %selects;
}
print;
}
if (%selects) {
foreach $k (sort (keys %selects)) {
print "$selects{$k}";
}
}
It found two duplicates:
Warning: removing duplicated S5P_SETUP_MIPIPHY entry
Warning: removing duplicated HARDIRQS_SW_RESEND entry
and they are identical duplicates, hence the shrinkage in the diffstat
of two lines.
We have four testers reporting success of this change (Tony, Stephen,
Linus and Sekhar.)
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pull third pile of kernel_execve() patches from Al Viro:
"The last bits of infrastructure for kernel_thread() et.al., with
alpha/arm/x86 use of those. Plus sanitizing the asm glue and
do_notify_resume() on alpha, fixing the "disabled irq while running
task_work stuff" breakage there.
At that point the rest of kernel_thread/kernel_execve/sys_execve work
can be done independently for different architectures. The only
pending bits that do depend on having all architectures converted are
restrictred to fs/* and kernel/* - that'll obviously have to wait for
the next cycle.
I thought we'd have to wait for all of them done before we start
eliminating the longjump-style insanity in kernel_execve(), but it
turned out there's a very simple way to do that without flagday-style
changes."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
alpha: switch to saner kernel_execve() semantics
arm: switch to saner kernel_execve() semantics
x86, um: convert to saner kernel_execve() semantics
infrastructure for saner ret_from_kernel_thread semantics
make sure that kernel_thread() callbacks call do_exit() themselves
make sure that we always have a return path from kernel_execve()
ppc: eeh_event should just use kthread_run()
don't bother with kernel_thread/kernel_execve for launching linuxrc
alpha: get rid of switch_stack argument of do_work_pending()
alpha: don't bother passing switch_stack separately from regs
alpha: take SIGPENDING/NOTIFY_RESUME loop into signal.c
alpha: simplify TIF_NEED_RESCHED handling
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
Pull second set of media updates from Mauro Carvalho Chehab:
"Despite its size, most of the stuff here is trivial. This series
contains:
- s5p-mfc: additions at the driver and at the core to support H.264
hardware codec;
- Some improvements at s5p and davinci embedded drivers;
- Some V4L2 compliance fixes applied on a few drivers;
- Several random trivial patches, including several fixes and a few
new board support additions;
Notes:
1) Some Exynos media patches were dependent on some -arm fixes that
got merged on changeset 782cd9e. That's why this pull request is
based that changeset.
2) As promised, I reviewed the pending VB2 DMABUF series.
While setting a test environment, it was noticed that the upstream
support for Samsung Exynos 4 boards (smdk310 and Origen) are
broken upstream, likely due to regressions: both defconfigs are
wrong and regulator settings for both boards are broken. That,
allied with some bug at the dummy regulator driver, causes OOPSes
during boot time.
Long story short: even fixing the above, the proposed patches
OOPSed when running the DMABUF test. Not sure yet if the OOPSes
are due to some other undetected regressions, or due to some bug
on the patches.
Due to the above, DMABUF patches for vb2 got NACKed for 3.7."
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (109 commits)
[media] m5mols: Add missing #include <linux/sizes.h>
[media] stk1160: Add support for S-Video input
Revert "[media] omap3isp: Replace cpu_is_omap3630() with ISP revision check"
[media] dvb: LNA implementation changes
[media] v4l2-ioctl: fix W=1 warnings
[media] v4l2-ioctl: add blocks check for VIDIOC_SUBDEV_G/S_EDID
[media] omap3isp: Fix compilation error in ispreg.h
[media] rc-msi-digivox-ii: Add full scan keycodes
[media] cx25821: testing the wrong variable
[media] tda18271-common: hold the I2C adapter during write transfers
[media] ds3000: add module parameter to force firmware upload
[media] drivers/media: Remove unnecessary semicolon
[media] winbond: remove space from driver name
[media] iguanair: cannot send data from the stack
[media] omap3isp: Replace cpu_is_omap3630() with ISP revision check
[media] dvb-usb: print small buffers via %*ph
[media] uvc: Add return code check at vb2_queue_init()
[media] em28xx: Replace memcpy with struct assignment
[media] bt8xx: Add video4linux control V4L2_CID_COLOR_KILLER
[media] mem2mem_testdev: Use devm_kzalloc() in probe
...
Conflicts:
arch/arm/mach-davinci/include/mach/da8xx.h
- Complement the Nomadik pinctrl driver with alternate Cx functions
so it handles all oddities.
- A patch to the IRQdomain to reform the simple irqdomain to handle
IRQ descriptor allocation dynamically.
- Use the above feature in the Nomadik pin controller.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=UKY/
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-for-3.7-late' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull second set of pinctrl patches from Linus Walleij:
"Here is a late pinctrl pull request with stuff that wasn't quite
tested at the first pull request.
The main reason to not hold off is that the modifications to
irq_domain_add_simple() as reviewed by Rob Herring introduce new
infrastructure for irqdomains that will be useful for the next cycle:
instead of sprinkling irq descriptor allocation all over the kernel
wherever a "legacy" domain is registered, which is necessary for any
platform using sparse IRQs, and many irq chips are say GPIO
controllers which may be used with several systems, some with sparse
IRQs some not, we push this into the irq_domain_add_simple() so we can
atleast do mistakes in one place.
The irq_domain_add_simple() is currently unused in the kernel, so I
need to provide a user. The Nomadik stuff that goes with are changes
to the driver I use day-to-day to make use of this facility (and a
dependency), so see it as a way to eat my own dogfood: if this blows
up the egg hits my face.
A second round of pinctrl patches for v3.7:
- Complement the Nomadik pinctrl driver with alternate Cx functions
so it handles all oddities.
- A patch to the IRQdomain to reform the simple irqdomain to handle
IRQ descriptor allocation dynamically.
- Use the above feature in the Nomadik pin controller."
* tag 'pinctrl-for-3.7-late' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl/nomadik: use simple or linear IRQ domain
irqdomain: augment add_simple() to allocate descs
pinctrl/nomadik: support other alternate-C functions
Pull second set of ARM updates from Russell King:
"This is the second set of ARM updates for this merge window.
Contained within are changes to allow the kernel to boot in hypervisor
mode on CPUs supporting virtualization, and cache flushing support to
the point of inner sharable unification, which are used by the
suspend/resume code to avoid having to do a full cache flush.
Also included is one fix for VFP code identified by Michael Olbrich."
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm:
ARM: vfp: fix saving d16-d31 vfp registers on v6+ kernels
ARM: 7549/1: HYP: fix boot on some ARM1136 cores
ARM: 7542/1: mm: fix cache LoUIS API for xscale and feroceon
ARM: mm: update __v7_setup() to the new LoUIS cache maintenance API
ARM: kernel: update __cpu_disable to use cache LoUIS maintenance API
ARM: kernel: update cpu_suspend code to use cache LoUIS operations
ARM: mm: rename jump labels in v7_flush_dcache_all function
ARM: mm: implement LoUIS API for cache maintenance ops
ARM: virt: arch_timers: enable access to physical timers
ARM: virt: Add CONFIG_ARM_VIRT_EXT option
ARM: virt: Add boot-time diagnostics
ARM: virt: Update documentation for hyp mode entry support
ARM: zImage/virt: hyp mode entry support for the zImage loader
ARM: virt: allow the kernel to be entered in HYP mode
ARM: opcodes: add __ERET/__MSR_ELR_HYP instruction encoding
Pull pile 2 of execve and kernel_thread unification work from Al Viro:
"Stuff in there: kernel_thread/kernel_execve/sys_execve conversions for
several more architectures plus assorted signal fixes and cleanups.
There'll be more (in particular, real fixes for the alpha
do_notify_resume() irq mess)..."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal: (43 commits)
alpha: don't open-code trace_report_syscall_{enter,exit}
Uninclude linux/freezer.h
m32r: trim masks
avr32: trim masks
tile: don't bother with SIGTRAP in setup_frame
microblaze: don't bother with SIGTRAP in setup_rt_frame()
mn10300: don't bother with SIGTRAP in setup_frame()
frv: no need to raise SIGTRAP in setup_frame()
x86: get rid of duplicate code in case of CONFIG_VM86
unicore32: remove pointless test
h8300: trim _TIF_WORK_MASK
parisc: decide whether to go to slow path (tracesys) based on thread flags
parisc: don't bother looping in do_signal()
parisc: fix double restarts
bury the rest of TIF_IRET
sanitize tsk_is_polling()
bury _TIF_RESTORE_SIGMASK
unicore32: unobfuscate _TIF_WORK_MASK
mips: NOTIFY_RESUME is not needed in TIF masks
mips: merge the identical "return from syscall" per-ABI code
...
Conflicts:
arch/arm/include/asm/thread_info.h
It includes:
- large updates for OMAP
- basic OMAP5 DSS support for DPI and DSI outputs
- large cleanups and restructuring
- some update to Exynos and da8xx-fb
- removal of the pnx4008 driver (arch removed)
- various other small patches
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.12 (GNU/Linux)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=EJUS
-----END PGP SIGNATURE-----
Merge tag 'fbdev-updates-for-3.7' of git://github.com/schandinat/linux-2.6
Pull fbdev updates from Florian Tobias Schandinat:
"This includes:
- large updates for OMAP
- basic OMAP5 DSS support for DPI and DSI outputs
- large cleanups and restructuring
- some update to Exynos and da8xx-fb
- removal of the pnx4008 driver (arch removed)
- various other small patches"
Fix up some trivial conflicts (mostly just include line changes, but
also some due to the renaming of the deferred work functions by Tejun).
* tag 'fbdev-updates-for-3.7' of git://github.com/schandinat/linux-2.6: (193 commits)
gbefb: fix compile error
video: mark nuc900fb_map_video_memory as __devinit
video/mx3fb: set .owner to prevent module unloading while being used
video: exynos_dp: use clk_prepare_enable and clk_disable_unprepare
drivers/video/exynos/exynos_mipi_dsi.c: fix error return code
drivers/video/savage/savagefb_driver.c: fix error return code
video: s3c-fb: use clk_prepare_enable and clk_disable_unprepare
da8xx-fb: save and restore LCDC context across suspend/resume cycle
da8xx-fb: add pm_runtime support
video/udlfb: fix line counting in fb_write
OMAPDSS: add missing include for string.h
OMAPDSS: DISPC: Configure color conversion coefficients for writeback
OMAPDSS: DISPC: Add manager like functions for writeback
OMAPDSS: DISPC: Configure writeback FIFOs
OMAPDSS: DISPC: Configure writeback specific parameters in dispc_wb_setup()
OMAPDSS: DISPC: Configure overlay-like parameters in dispc_wb_setup
OMAPDSS: DISPC: Add function to set channel in for writeback
OMAPDSS: DISPC: Don't set chroma resampling bit for writeback
OMAPDSS: DISPC: Downscale chroma if plane is writeback
OMAPDSS: DISPC: Configure input and output sizes for writeback
...
Applied on the top of changeset 782cd9e, as some of those patches
depend on some fixes that went via -arm tree.
* staging/for_v3.7: (109 commits)
[media] m5mols: Add missing #include <linux/sizes.h>
[media] stk1160: Add support for S-Video input
Revert "[media] omap3isp: Replace cpu_is_omap3630() with ISP revision check"
[media] dvb: LNA implementation changes
[media] v4l2-ioctl: fix W=1 warnings
[media] v4l2-ioctl: add blocks check for VIDIOC_SUBDEV_G/S_EDID
[media] omap3isp: Fix compilation error in ispreg.h
[media] rc-msi-digivox-ii: Add full scan keycodes
[media] cx25821: testing the wrong variable
[media] tda18271-common: hold the I2C adapter during write transfers
[media] ds3000: add module parameter to force firmware upload
[media] drivers/media: Remove unnecessary semicolon
[media] winbond: remove space from driver name
[media] iguanair: cannot send data from the stack
[media] omap3isp: Replace cpu_is_omap3630() with ISP revision check
[media] dvb-usb: print small buffers via %*ph
[media] uvc: Add return code check at vb2_queue_init()
[media] em28xx: Replace memcpy with struct assignment
[media] bt8xx: Add video4linux control V4L2_CID_COLOR_KILLER
[media] mem2mem_testdev: Use devm_kzalloc() in probe
...
Pull i2c-embedded changes from Wolfram Sang:
"The changes for i2c-embedded include:
- massive rework of the omap driver
- massive rework of the at91 driver. In fact, the old driver gets
removed; I am okay with this approach since the old driver was
depending on BROKEN and its limitations made it practically
unusable, so people used bitbanging instead. But even if there are
users, there is no platform_data or module parameter which would
need to be converted. It is just another driver doing I2C
transfers, just way better. Modifications of arch/arm/at91 related
files have proper acks from the maintainer.
- new driver for R-Car I2C
- devicetree and generic_clock conversions and fixes
- usual driver fixes and changes.
The rework patches have come a long way and lots of people have been
involved in creating/testing them. Most patches have been in
linux-next at least since 3.6-rc5. A few have been added in the last
week, I have to admit.
An unexpected (but welcome :)) peak in private life is the cause for
that. The "late" patches shouldn't cause any merge conflicts and I
will have a special eye on them during the stabilization phase. This
is an exception and I want to have the patches in place properly in
time again for the next kernels."
* 'i2c-embedded/for-next' of git://git.pengutronix.de/git/wsa/linux: (44 commits)
MXS: Implement DMA support into mxs-i2c
i2c: add Renesas R-Car I2C driver
i2c: s3c2410: use clk_prepare_enable and clk_disable_unprepare
ARM: OMAP: convert I2C driver to PM QoS for MPU latency constraints
i2c: nomadik: Add Device Tree support to the Nomadik I2C driver
i2c: algo: pca: Fix chip reset function for PCA9665
i2c: mpc: Wait for STOP to hit the bus
i2c: davinci: preparation for switch to common clock framework
omap-i2c: fix incorrect log message when using a device tree
i2c: omap: sanitize exit path
i2c: omap: switch over to autosuspend API
i2c: omap: remove unnecessary pm_runtime_suspended check
i2c: omap: switch to threaded IRQ support
i2c: omap: remove redundant status read
i2c: omap: get rid of the "complete" label
i2c: omap: resize fifos before each message
i2c: omap: simplify IRQ exit path
i2c: omap: always return IRQ_HANDLED
i2c: omap: simplify errata check
i2c: omap: bus: add a receiver flag
...
A series of fixes (and in some cases, some cleanups):
Via Tony Lindgren:
- A collection of OMAP regression fixes, in particular because firmware
no longer sets up all pin states before starting the kernel.
- cpufreq fixes for OMAP (Rafael is on vacation and this was pre-agreed).
- A longer series of misc regression fixes and cleanups, warning removals,
etc for OMAP
From Arnd Bergmann:
- A series of warning fixes for various platforms (defconfig builds)
Misc:
- A couple of tegra fixes, one for i.MX, some vt8500 fixes, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=vAh+
-----END PGP SIGNATURE-----
Merge tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A series of fixes (and in some cases, some cleanups):
Via Tony Lindgren:
- A collection of OMAP regression fixes, in particular because
firmware no longer sets up all pin states before starting the
kernel.
- cpufreq fixes for OMAP (Rafael is on vacation and this was
pre-agreed).
- A longer series of misc regression fixes and cleanups, warning
removals, etc for OMAP
From Arnd Bergmann:
- A series of warning fixes for various platforms (defconfig builds)
Misc:
- A couple of tegra fixes, one for i.MX, some vt8500 fixes, etc."
* tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (73 commits)
ARM: pxa: armcore: fix PCI PIO warnings
ARM: integrator: use __iomem pointers for MMIO, part 2
ARM: assabet: fix bogus warning in get_assabet_scr (again)
ARM: shmobile: mark shmobile_init_late as __init
ARM: integrator_cp: fix build failure
ARM: OMAP4/AM335x: hwmod: fix disable_module regression in hardreset handling
ARM: OMAP3: fix workaround for EMU clockdomain
arm/omap: Replace board_ref_clock with enum values
ARM: OMAP2+: remove duplicated include from board-omap3stalker.c
arch/arm/plat-omap/omap-pm-noop.c: Remove unecessary semicolon
arch/arm/mach-omap2: Remove unecessary semicolon
arch/arm/mach-omap1/devices.c: Remove unecessary semicolon
ARM/dts: omap5-evm: pinmux configuration for audio
ARM/dts: Add pinctrl driver entries for omap5
ARM/dts: omap4-panda: pinmux configuration for audio
ARM/dts: omap4-sdp: pinmux configuration for audio
ARM/dts: omap5-evm: Disable unused McBSP3
ARM/dts: omap4-sdp: Disable unused McBSP3
ARM/dts: omap4-panda: Disable unused audio IPs
ARM: OMAP: board-omap4panda: Pin mux configuration for audio needs
...
Upgrade nomadik pinctrl driver to enable selection of other
alternate-C[1-4] functions on some specific ux500 SoC pins.
Handling of those functions is done thanks to PRCM GPIOCR
registers. This was previously managed in PRCMU driver and
it was not really convenient. Idea is to provide a common
way to control all alternate functions.
Note that this improvement does not support the old-fashioned way
used to control nomadik pins, namely the "nmk_config_pin()" function
and its derivatives.
Signed-off-by: Jean-Nicolas Graux <jean-nicolas.graux@stericsson.com>
Reviewed-by: Philippe Langlais <philippe.langlais@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull generic execve() changes from Al Viro:
"This introduces the generic kernel_thread() and kernel_execve()
functions, and switches x86, arm, alpha, um and s390 over to them."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal: (26 commits)
s390: convert to generic kernel_execve()
s390: switch to generic kernel_thread()
s390: fold kernel_thread_helper() into ret_from_fork()
s390: fold execve_tail() into start_thread(), convert to generic sys_execve()
um: switch to generic kernel_thread()
x86, um/x86: switch to generic sys_execve and kernel_execve
x86: split ret_from_fork
alpha: introduce ret_from_kernel_execve(), switch to generic kernel_execve()
alpha: switch to generic kernel_thread()
alpha: switch to generic sys_execve()
arm: get rid of execve wrapper, switch to generic execve() implementation
arm: optimized current_pt_regs()
arm: introduce ret_from_kernel_execve(), switch to generic kernel_execve()
arm: split ret_from_fork, simplify kernel_thread() [based on patch by rmk]
generic sys_execve()
generic kernel_execve()
new helper: current_pt_regs()
preparation for generic kernel_thread()
um: kill thread->forking
um: let signal_delivered() do SIGTRAP on singlestepping into handler
...
Notable changes:
* Basic writeback support for DISPC level. Writeback is not yet usable, though,
as we need higher level code to actually expose the writeback feature to
userspace.
* Rewriting the omapdss output drivers. We're trying to remove the hard links
between the omapdss and the panels, and this rewrite work moves us closer to
that goal.
* Cleanup and restructuring patches that have been made while working on device
tree support for omapdss. Device tree support is still some way ahead, but
these patches are good cleanups in themselves.
* Basic OMAP5 DSS support for DPI and DSI outputs.
* Workaround for the problem that GFX overlay's fifo is too small for high
resolution scenarios, causing underflows.
* Cleanups that remove dependencies to omap platform code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=lcyJ
-----END PGP SIGNATURE-----
Merge tag 'omapdss-for-3.7' of git://gitorious.org/linux-omap-dss2/linux into fbdev-next
Omapdss driver changes for the 3.7 merge window.
Notable changes:
* Basic writeback support for DISPC level. Writeback is not yet usable, though,
as we need higher level code to actually expose the writeback feature to
userspace.
* Rewriting the omapdss output drivers. We're trying to remove the hard links
between the omapdss and the panels, and this rewrite work moves us closer to
that goal.
* Cleanup and restructuring patches that have been made while working on device
tree support for omapdss. Device tree support is still some way ahead, but
these patches are good cleanups in themselves.
* Basic OMAP5 DSS support for DPI and DSI outputs.
* Workaround for the problem that GFX overlay's fifo is too small for high
resolution scenarios, causing underflows.
* Cleanups that remove dependencies to omap platform code.
Pull slave-dmaengine updates from Vinod Koul:
"This time we have Andy updates on dw_dmac which is attempting to make
this IP block available as PCI and platform device though not fully
complete this time.
We also have TI EDMA moving the dma driver to use dmaengine APIs, also
have a new driver for mmp-tdma, along with bunch of small updates.
Now for your excitement the merge is little unusual here, while
merging the auto merge on linux-next picks wrong choice for pl330
(drivers/dma/pl330.c) and this causes build failure. The correct
resolution is in linux-next. (DMA: PL330: Fix build error) I didn't
back merge your tree this time as you are better than me so no point
in doing that for me :)"
Fixed the pl330 conflict as in linux-next, along with trivial header
file conflicts due to changed includes.
* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (29 commits)
dma: tegra: fix interrupt name issue with apb dma.
dw_dmac: fix a regression in dwc_prep_dma_memcpy
dw_dmac: introduce software emulation of LLP transfers
dw_dmac: autoconfigure data_width or get it via platform data
dw_dmac: autoconfigure block_size or use platform data
dw_dmac: get number of channels from hardware if possible
dw_dmac: fill optional encoded parameters in register structure
dw_dmac: mark dwc_dump_chan_regs as inline
DMA: PL330: return ENOMEM instead of 0 from pl330_alloc_chan_resources
DMA: PL330: Remove redundant runtime_suspend/resume functions
DMA: PL330: Remove controller clock enable/disable
dmaengine: use kmem_cache_zalloc instead of kmem_cache_alloc/memset
DMA: PL330: Set the capability of pdm0 and pdm1 as DMA_PRIVATE
ARM: EXYNOS: Set the capability of pdm0 and pdm1 as DMA_PRIVATE
dma: tegra: use list_move_tail instead of list_del/list_add_tail
mxs/dma: Enlarge the CCW descriptor area to 4 pages
dw_dmac: utilize slave_id to pass request line
dmaengine: mmp_tdma: add dt support
dmaengine: mmp-pdma support
spi: davici - make davinci select edma
...
Core:
- Add DT properties for card detection (broken-cd, cd-gpios, non-removable)
- Don't poll non-removable devices
- Fixup/rework eMMC sleep mode/"power off notify" feature
- Support eMMC background operations (BKOPS). To set the one-time
programmable fuse that enables bkops on an eMMC that doesn't already
have it set, you can use the "mmc bkops enable" command in:
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc-utils.git
Drivers:
- atmel-mci, dw_mmc, pxa-mci, dove, s3c, spear: Add device tree support
- bfin_sdh: Add support for the controller in bf60x
- dw_mmc: Support Samsung Exynos SoCs
- eSDHC: Add ADMA support
- sdhci: Support testing a cd-gpio (from slot-gpio) instead of presence bit
- sdhci-pltfm: Support broken-cd DT property
- tegra: Convert to only supporting DT (mach-tegra has gone DT-only)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=qyY5
-----END PGP SIGNATURE-----
Merge tag 'mmc-merge-for-3.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
"Core:
- Add DT properties for card detection (broken-cd, cd-gpios,
non-removable)
- Don't poll non-removable devices
- Fixup/rework eMMC sleep mode/"power off notify" feature
- Support eMMC background operations (BKOPS). To set the one-time
programmable fuse that enables bkops on an eMMC that doesn't
already have it set, you can use the "mmc bkops enable" command in:
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc-utils.git
Drivers:
- atmel-mci, dw_mmc, pxa-mci, dove, s3c, spear: Add device tree
support
- bfin_sdh: Add support for the controller in bf60x
- dw_mmc: Support Samsung Exynos SoCs
- eSDHC: Add ADMA support
- sdhci: Support testing a cd-gpio (from slot-gpio) instead of
presence bit
- sdhci-pltfm: Support broken-cd DT property
- tegra: Convert to only supporting DT (mach-tegra has gone DT-only)"
* tag 'mmc-merge-for-3.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (67 commits)
mmc: core: Fixup broken suspend and eMMC4.5 power off notify
mmc: sdhci-spear: Add clk_{un}prepare() support
mmc: sdhci-spear: add device tree bindings
mmc: sdhci-s3c: Add clk_(enable/disable) in runtime suspend/resume
mmc: core: Replace MMC_CAP2_BROKEN_VOLTAGE with test for fixed regulator
mmc: sdhci-pxav3: Use sdhci_get_of_property for parsing DT quirks
mmc: dt: Support "broken-cd" property in sdhci-pltfm
mmc: sdhci-s3c: fix the wrong number of max bus clocks
mmc: sh-mmcif: avoid oops on spurious interrupts
mmc: sh-mmcif: properly handle MMC_WRITE_MULTIPLE_BLOCK completion IRQ
mmc: sdhci-s3c: Fix crash on module insertion for second time
mmc: sdhci-s3c: Enable only required bus clock
mmc: Revert "mmc: dw_mmc: Add check for IDMAC configuration"
mmc: mxcmmc: fix bug that may block a data transfer forever
mmc: omap_hsmmc: Pass on the suspend failure to the PM core
mmc: atmel-mci: AP700x PDC is not connected to MCI
mmc: atmel-mci: DMA can be used with other controllers
mmc: mmci: use clk_prepare_enable and clk_disable_unprepare
mmc: sdhci-s3c: Add device tree support
mmc: dw_mmc: add support for exynos specific implementation of dw-mshc
...
From Tony Lindgren:
This branch contains regression fixes for omap4/5 ASoC
audio that were caused by the fact that u-boot stopped
muxing non essential pins.
As omap audio and dmaengine development happens on
these platforms, let's make sure they are usable.
Of course this should have been fixed earlier and
not during the -rc cycle.
* tag 'omap-for-v3.7-rc1/fixes-asoc-regression-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM/dts: omap5-evm: pinmux configuration for audio
ARM/dts: Add pinctrl driver entries for omap5
ARM/dts: omap4-panda: pinmux configuration for audio
ARM/dts: omap4-sdp: pinmux configuration for audio
ARM/dts: omap5-evm: Disable unused McBSP3
ARM/dts: omap4-sdp: Disable unused McBSP3
ARM/dts: omap4-panda: Disable unused audio IPs
ARM: OMAP: board-omap4panda: Pin mux configuration for audio needs
ARM: OMAP: board-4430-sdp: Pin mux configuration for audio needs
From Tony Lindgren:
These were agreed to be merged via arm soc tree as Rafael
is on vacation.
From Kevin Hilman <khilman@deeprootsystems.com>:
This series a couple bug fixes and a couple fixes that make this
driver support recently added OMAP-based SoCs.
The 'get_cpu_device' patch is needed due to a change in the OMAP
OMAP PM core code which enforces use of get_cpu_device() instead of
a deprecated OMAP-specific API.
The usage of plat/*.h headers breaks single zImage, so platforms are
cleaning up and/or removing plat/*.h so the driver needs to be fixed
accordingly.
This series is based on the merge of Rafael's pm-for-3.7-rc1 tag into
Linus' master branch: commit 16642a2e7b.
* tag 'omap-for-v3.7-rc1/fixes-cpufreq-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: PM: MPU DVFS: use generic CPU device for MPU-SS
cpufreq: OMAP: use get_cpu_device() instead of omap_device API
cpufreq: OMAP: fix clock usage to be SoC independent, remove plat/ includes
cpufreq: OMAP: remove unused <plat/omap-pm.h>
cpufreq: OMAP: ensure valid clock rate before scaling
From Kevin Hilman <khilman@deeprootsystems.com> via Tony Lindgren:
OMAP PM related fixes for v3.7-rc
* tag 'omap-for-v3.7-rc1/fixes-pm-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: SmartReflex: fix error path in init function
ARM: OMAP: SmartReflex: select CONFIG_POWER_SUPPLY in Kconfig
ARM: OMAP2+: PM: fix return value check in omap2_set_init_voltage()
ARM: OMAP2+: SmartReflex: fix return value check in sr_dev_init()
ARM: OMAP: omap_device: fix return value check in omap_device_build_ss()
ARM: OMAP: fix return value check in beagle_opp_init()
From Paul Walmsley <paul@pwsan.com> via Tony Lindgren:
Some OMAP fixes for the 3.7 merge window, fixing mismerges, branch
integration issues, and bugs after the arm-soc merges.
* tag 'omap-for-v3.7-rc1/fixes-hwmod-clock-signed-v3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP4/AM335x: hwmod: fix disable_module regression in hardreset handling
ARM: OMAP3: fix workaround for EMU clockdomain
ARM: OMAP: omap3evm: fix new sparse warning
ARM: OMAP2+: hwmod data: Fix PMU interrupt definitions
ARM: am33xx: clk: Update clkdev table to add mcasp alias
From Tony Lindgren:
This branch contains one counter locking fix and an
alignment fix. Other fixes are warning fixes, fixes
for return value checks.
I've also included removal of some extra semicolons,
dropping of some duplicate includes, and an a change
for wl12xx enumeration that are not strictly fixes
but would be good to get out of the way for -rc1.
* tag 'omap-for-v3.7-rc1/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
arm/omap: Replace board_ref_clock with enum values
ARM: OMAP2+: remove duplicated include from board-omap3stalker.c
arch/arm/plat-omap/omap-pm-noop.c: Remove unecessary semicolon
arch/arm/mach-omap2: Remove unecessary semicolon
arch/arm/mach-omap1/devices.c: Remove unecessary semicolon
AM35xx: Add missing hwmod entry for the HDQ/1-Wire present in AM3505/3517 CPUs.
ARM: OMAP2+: gpmc: annotate exit sections properly
ARM: OMAP: fix return value check in realtime_counter_init()
ARM: OMAP: hsmmc: fix return value check in omap_hsmmc_init_one()
OMAPDSS: fix return value check in create_dss_pdev()
ARM: OMAP2+: Add am335x evm and bone targets to common Makefile
arm: increase FORCE_MAX_ZONEORDER for TI AM33XX
ARM: OMAP: OMAP_DEBUG_LEDS needs to select LEDS_CLASS
ARM: OMAP: rx51: Fix a section mismatch warn
ARM: OMAP2+: Round of the carve out memory requested to section_size
ARM: OMAP: counter: add locking to read_persistent_clock
The it8152 PCI host used on the pxa/cm_x2xx machines
uses the old-style I/O window registration. This should
eventually get converted to pci_ioremap_io() but for
now, let's cast the IT8152_IO_BASE constant to an integer
type to get rid of the warnings.
Without this patch, building cm_x2xx_defconfig results in:
arch/arm/common/it8152.c: In function 'it8152_pci_setup':
arch/arm/common/it8152.c:287:18: warning: assignment makes integer from pointer without a cast [enabled by default]
arch/arm/common/it8152.c:288:16: warning: assignment makes integer from pointer without a cast [enabled by default]
arch/arm/common/it8152.c:291:17: warning: assignment makes integer from pointer without a cast [enabled by default]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Cc: Mike Rapoport <mike@compulab.co.il>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Due to some interesting merges in the integrator code, not
all users of mmio pointers were converted before, this
fixes all warnings that got introduced as a consequence.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Russell fixed this bogus warning before in 2f3eca8b4f "Shut up gcc
warning in assabet.c", but apparently gcc has become smarter (or dumber)
since 2005, and the same warning came up again.
This uses the uninitialized_var() macro to convince gcc that the
variable is actually being initialized. 100 times in fact.
Without this patch, building assabet_defconfig results in:
arch/arm/mach-sa1100/assabet.c: In function 'fixup_assabet':
arch/arm/mach-sa1100/assabet.c:397:6: warning: 'scr' may be used uninitialized in this function [-Wuninitialized]
arch/arm/mach-sa1100/assabet.c:389:16: note: 'scr' was declared here
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Patch 35f2b0bd59 "ARM: shmobile: Move definition of shmobile_init_late()
to header" moved the definition of the shmobile_init_late function, but
dropped the __init annotation, which is now causing warnings because
the function calls shmobile_suspend_init, which is also marked init.
Without this patch, building kota2_defconfig results in:
WARNING: vmlinux.o(.text+0xb7c8): Section mismatch in reference from the function shmobile_init_late() to the function .init.text:shmobile_suspend_init()
The function shmobile_init_late() references
the function __init shmobile_suspend_init().
This is often because shmobile_init_late lacks a __init
annotation or the annotation of shmobile_suspend_init is wrong.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Magnus Damm <damm@opensource.se>
Cc: Simon Horman <horms@verge.net.au>
Michael Olbrich reported that his test program fails when built with
-O2 -mcpu=cortex-a8 -mfpu=neon, and a kernel which supports v6 and v7
CPUs:
volatile int x = 2;
volatile int64_t y = 2;
int main() {
volatile int a = 0;
volatile int64_t b = 0;
while (1) {
a = (a + x) % (1 << 30);
b = (b + y) % (1 << 30);
assert(a == b);
}
}
and two instances are run. When built for just v7 CPUs, this program
works fine. It uses the "vadd.i64 d19, d18, d16" VFP instruction.
It appears that we do not save the high-16 double VFP registers across
context switches when the kernel is built for v6 CPUs. Fix that.
Cc: <stable@vger.kernel.org>
Tested-By: Michael Olbrich <m.olbrich@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It appears that performing a "movs pc, lr" to force the kernel into
SVC mode on the OMAP2420 (ARM1136) prevents the platform from booting
correctly (change introduced in 80c59da [ARM: virt: allow the kernel
to be entered in HYP mode]).
While the reason it fails is not understood yet (the same code runs
fine on the OMAP2430, ARM1136 as well), partially revert that change
for platforms that do not enter in HYP mode, preserving the new
feature and restoring a working kernel on the OMAP2420.
Reported-by: Tony Lindgren <tony@atomide.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
.fault now can retry. The retry can break state machine of .fault. In
filemap_fault, if page is miss, ra->mmap_miss is increased. In the second
try, since the page is in page cache now, ra->mmap_miss is decreased. And
these are done in one fault, so we can't detect random mmap file access.
Add a new flag to indicate .fault is tried once. In the second try, skip
ra->mmap_miss decreasing. The filemap_fault state machine is ok with it.
I only tested x86, didn't test other archs, but looks the change for other
archs is obvious, but who knows :)
Signed-off-by: Shaohua Li <shaohua.li@fusionio.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Implement an interval tree as a replacement for the VMA prio_tree. The
algorithms are similar to lib/interval_tree.c; however that code can't be
directly reused as the interval endpoints are not explicitly stored in the
VMA. So instead, the common algorithm is moved into a template and the
details (node type, how to get interval endpoints from the node, etc) are
filled in using the C preprocessor.
Once the interval tree functions are available, using them as a
replacement to the VMA prio tree is a relatively simple, mechanical job.
Signed-off-by: Michel Lespinasse <walken@google.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Hillf Danton <dhillf@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce HAVE_DEBUG_KMEMLEAK config option and select it in corresponding
architecture Kconfig files. DEBUG_KMEMLEAK now only depends on
HAVE_DEBUG_KMEMLEAK.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce HAVE_UID16 config option and select it in corresponding
architecture Kconfig files. UID16 now only depends on HAVE_UID16.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit eb05f69129 ("ARM: OMAP: hwmod:
partially un-reset hwmods might not be properly enabled") added code
to skip the IP block disable sequence if all of the block's hardreset
lines weren't asserted. But this did not handle the case when no
hardreset lines were associated with a module, which is the general
case. In that situation, the IP block disable would be skipped. This
is likely to cause PM regressions.
So, modify _omap4_disable_module() and _am33xx_disable_module() to
only bail out early if there are any hardreset lines asserted. And
move the AM33xx test above the actual module disable code to ensure
that the behavior is consistent.
Reported-by: Archit Taneja <a0393947@ti.com>
Tested-by: Archit Taneja <a0393947@ti.com> # DSS
Cc: Omar Ramirez Luna <omar.luna@linaro.org>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com> # AM335x
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit b71c721 (ARM: OMAP2+: clockdomain/hwmod: add workaround for EMU
clockdomain idle problems) added a workaround for the EMU clock domain on
OMAP3/4 devices to prevent the clock domain for transitioning while it is
in use.
In the proposed patch [1] code was added to the omap3xxx_clkdm_clk_enable()
and omap3xxx_clkdm_clk_disable() functions to check for the flag
CLKDM_MISSING_IDLE_REPORTING and perform the appropriate action. However, in the
merged patch it appears that this code was added to the omap2_clkdm_clk_enable()
and omap2_clkdm_clk_disable() functions by mistake.
[1] http://marc.info/?l=linux-arm-kernel&m=134383567112518&w=2
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Use the enum for board_ref_clock from linux/wl12xx.h
Signed-off-by: Vikram Narayanan <vikram186@gmail.com>
Cc: linux-omap@vger.kernel.org
Reviewed-by: Pankaj Jangra<jangra.pankaj9@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove duplicated include.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Tony Lindgren <tony@atomide.com>
u-boot stopped configuring 'non essential' pins recently. The kernel needs
to configure the mux for audio needs.
Since the pinmux for these IPs are static let pinctrl to handle the mux
configuration for.
Configuring the mux for: twl6040 (audpwron), McPDM, DMIC, McBSP1 and McBSP2.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
These all use the generic pinctrl-single driver for the padconf registers.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
u-boot stopped configuring 'non essential' pins recently. The kernel needs
to configure the mux for audio needs.
Since the pinmux for these IPs are static let pinctrl to handle the mux
configuration for.
Configuring the mux for: twl6040 (audpwron, irq), McPDM and McBSP1.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
u-boot stopped configuring 'non essential' pins recently. The kernel needs
to configure the mux for audio needs.
Since the pinmux for these IPs are static let pinctrl to handle the mux
configuration for.
Configuring the mux for: twl6040 (audpwron, irq), McPDM, DMIC, McBSP1 and
McBSP2.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
McBSP3 is not usable on OMAP4 SDP/Blaze (the pins used for McPDM).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
McBSP3 is not usable on OMAP4 SDP/Blaze (the pins used for McPDM).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
McBSP2, McBSP3 and DMIC is not usable on PandaBoard (not connected, no
external pins provided for them).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
u-boot stopped configuring 'non essential' pins recently. These pins are
essential for audio and need to be done to have working audio on the board.
Pin Mux configuration for: twl6040 audpwron gpio, McPDM, and McBSP1.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
u-boot stopped configuring 'non essential' pins recently. These pins are
essential for audio and need to be done to have working audio on the board.
Pin Mux configuration for: twl6040 audpwron gpio, McPDM, DMIC, McBSP1 and
McBSP2.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
driver support recently added OMAP-based SoCs.
The 'get_cpu_device' patch is needed due to a change in the OMAP
OMAP PM core code which enforces use of get_cpu_device() instead of
a deprecated OMAP-specific API.
The usage of plat/*.h headers breaks single zImage, so platforms are
cleaning up and/or removing plat/*.h so the driver needs to be fixed
accordingly.
This series is based on the merge of Rafael's pm-for-3.7-rc1 tag into
Linus' master branch: commit 16642a2e7b.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=kteZ
-----END PGP SIGNATURE-----
Merge tag 'for_3.7-fixes-cpufreq' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-omap-pm into omap-for-v3.7-rc1/fixes-cpufreq
This series a couple bug fixes and a couple fixes that make this
driver support recently added OMAP-based SoCs.
The 'get_cpu_device' patch is needed due to a change in the OMAP
OMAP PM core code which enforces use of get_cpu_device() instead of
a deprecated OMAP-specific API.
The usage of plat/*.h headers breaks single zImage, so platforms are
cleaning up and/or removing plat/*.h so the driver needs to be fixed
accordingly.
This series is based on the merge of Rafael's pm-for-3.7-rc1 tag into
Linus' master branch: commit 16642a2e7b.
This patch adds a missing hwmod entry for the HDQ/1-Wire module present
in the AM3505/17 CPUs.
This restores 1-Wire support to our AM3505 boards. We think it probably
stopped working with commit 96b1b29d37
ARM: OMAP2+: HDQ1W: use omap_device
Signed-off-by: Raphael Assenat <raph@8d.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
compiler complained,
`gpmc_remove' referenced in section `.data' of arch/arm/mach-omap2/built-in.o: defined in discarded section `.exit.text' of arch/arm/mach-omap2/built-in.o
Annotate gpmc_remove function and dependents with __devexit.
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In case of error, the function clk_get() returns ERR_PTR()
and never returns NULL. The NULL test in the return value
check should be replaced with IS_ERR().
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In case of error, the function omap_device_alloc() returns ERR_PTR()
not NULL pointer. The NULL test in the return value check should
be replaced with IS_ERR().
dpatch engine is used to auto generated this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In case of error, the function omap_device_alloc() returns ERR_PTR()
not NULL pointer. The NULL test in the return value check should
be replaced with IS_ERR().
dpatch engine is used to auto generated this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds am335x-evm and am335x-bone dtb targets to
'make dtbs', just like other platforms.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
FORCE_MAX_ZONEORDER of 12 is needed to allocation more than 4MB
of consistent DMA memory (da8xx frame buffer driver).
Signed-off-by: Dejan Gacnik <dejan.gacnik@gmail.com>
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This fixes below build error when CONFIG_LEDS_CLASS is not set.
LD init/built-in.o
arch/arm/plat-omap/built-in.o: In function `fpga_probe':
arch/arm/plat-omap/debug-leds.c:113: undefined reference to `led_classdev_register'
make: *** [vmlinux] Error 1
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This contains pretty many small commits covering fairly large range of
files in sound/ directory. Partly because of additional API support
and partly because of constantly developed ASoC and ARM stuff.
Some highlights:
- Introduced the helper function and documentation for exposing the
channel map via control API, as discussed in Plumbers; most of PCI
drivers are covered, will follow more drivers later
- Most of drivers have been replaced with the new PM callbacks (if
the bus is supported)
- HD-audio controller got the support of runtime PM and the support of
D3 clock-stop. Also changing the power_save option in sysfs kicks
off immediately to enable / disable the power-save mode.
- Another significant code change in HD-audio is the rewrite of
firmware loading code. Other than that, most of changes in HD-audio
are continued cleanups and standardization for the generic auto
parser and bug fixes (HBR, device-specific fixups), in addition to
the support of channel-map API.
- Addition of ASoC bindings for the compressed API, used by the
mid-x86 drivers.
- Lots of cleanups and API refreshes for ASoC codec drivers and
DaVinci.
- Conversion of OMAP to dmaengine.
- New machine driver for Wolfson Microelectronics Bells.
- New CODEC driver for Wolfson Microelectronics WM0010.
- Enhancements to the ux500 and wm2000 drivers
- A new driver for DA9055 and the support for regulator bypass mode.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQIcBAABAgAGBQJQcpeWAAoJEGwxgFQ9KSmkpi4P/2etDDz5aEkEHNa1l4xEmFcm
ymiGTgjaalqpUAVbM/gYx9G59EFMEbzUl1BHAqE5La4wO/v9lNPb+VrdUo+B+NZ7
WSxIPWcNqdinSuoSqyYPjoPMVnhs3EMtNOqmf4jm1JOvdqA+4rO29xQVAqK/5Gfu
LpMOyPiRi5ODnbQ1BOIWwpKICioY/mLwGJudK3z0i/fYVA7gLub20f+w+sOjKIA4
wmwQAMTjAR798Cg/tVy4fQmf4SLw+c2nIgGe/PD+2gVlGXLNKBrJfMonHPTbmwKu
lmJO/EtnijNOnpbn6up7ryUQ9cSoZAUZOfdIOgmAeQgQ/LWR0f+zf2IQehSPwrul
g6hqOnQI2DNN7ugT3cYVbYnsh56TjyhnxhhxZgkapqh706QkqHGyKJNMRetzuXmP
1O//MnZJrFQWd6sOKLlTL2ZzRvnxEJcNVGaE6bbwZTfQMtPeo9l1842uIq1dLUtG
VxZb/svKUkMXv4is1dwUYUkpDsKxsgMEmabmuovceGf2N7jj/irkXgqxf6LWkaY1
JQ7ZFWUJyDzEMXRaFfzdGO15T532CfB84wvFX5xoPMwMste2AA7QuybFBVstXhKu
AtKNDgRJFUTlnLIxydpPBWdWH3UJdEaFwwsSfuNKI8OmmGKhWC/aP83k4hzueu9H
KYLvY/0ObMSMqiwh/ndQ
=uNqD
-----END PGP SIGNATURE-----
Merge tag 'sound-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This contains pretty many small commits covering fairly large range of
files in sound/ directory. Partly because of additional API support
and partly because of constantly developed ASoC and ARM stuff.
Some highlights:
- Introduced the helper function and documentation for exposing the
channel map via control API, as discussed in Plumbers; most of PCI
drivers are covered, will follow more drivers later
- Most of drivers have been replaced with the new PM callbacks (if
the bus is supported)
- HD-audio controller got the support of runtime PM and the support
of D3 clock-stop. Also changing the power_save option in sysfs
kicks off immediately to enable / disable the power-save mode.
- Another significant code change in HD-audio is the rewrite of
firmware loading code. Other than that, most of changes in
HD-audio are continued cleanups and standardization for the generic
auto parser and bug fixes (HBR, device-specific fixups), in
addition to the support of channel-map API.
- Addition of ASoC bindings for the compressed API, used by the
mid-x86 drivers.
- Lots of cleanups and API refreshes for ASoC codec drivers and
DaVinci.
- Conversion of OMAP to dmaengine.
- New machine driver for Wolfson Microelectronics Bells.
- New CODEC driver for Wolfson Microelectronics WM0010.
- Enhancements to the ux500 and wm2000 drivers
- A new driver for DA9055 and the support for regulator bypass mode."
Fix up various arm soc header file reorg conflicts.
* tag 'sound-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (339 commits)
ALSA: hda - Add new codec ALC283 ALC290 support
ALSA: hda - avoid unneccesary indices on "Headphone Jack" controls
ALSA: hda - fix indices on boost volume on Conexant
ALSA: aloop - add locking to timer access
ALSA: hda - Fix hang caused by race during suspend.
sound: Remove unnecessary semicolon
ALSA: hda/realtek - Fix detection of ALC271X codec
ALSA: hda - Add inverted internal mic quirk for Lenovo IdeaPad U310
ALSA: hda - make Realtek/Sigmatel/Conexant use the generic unsol event
ALSA: hda - make a generic unsol event handler
ASoC: codecs: Add DA9055 codec driver
ASoC: eukrea-tlv320: Convert it to platform driver
ALSA: ASoC: add DT bindings for CS4271
ASoC: wm_hubs: Ensure volume updates are handled during class W startup
ASoC: wm5110: Adding missing volume update bits
ASoC: wm5110: Add OUT3R support
ASoC: wm5110: Add AEC loopback support
ASoC: wm5110: Rename EPOUT to HPOUT3
ASoC: arizona: Add more clock rates
ASoC: arizona: Add more DSP options for mixer input muxes
...
Currently, a dummy omap_device is created for the MPU sub-system so
that a device node exists for MPU DVFS. Specifically, for the
association of MPU OPPs to a device node, and so that a voltage
regulator can be mapped to a device node.
For drivers to get a handle to this device node, an OMAP-specific API
has been used. However, the kernel already has device nodes for the
CPU(s) in the system, so we can use those instead of an OMAP-specific
dummy device and then drivers (like OMAP CPUfreq) can use generic
APIs.
To use the existing CPU device nodes, modify the OPP creation and
regulator registration to use the CPU0 device node for registraion.
NOTE: this patch always uses CPU0 as the device node. On all
OMAPs today, MPU DVFS scales all CPUs together, so this will
not be a problem, but this assumption will need to be changed
if independently scalable CPUs are introduced.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
rx51_si4713_dev is referenced only from rx51_init_si4713.
So the memory for rx51_si4713_dev can be safely freed after init.
Also it references rx51_si4713_board_info which is __initdata_or_module.
fixes the below warning.
WARNING: vmlinux.o(.data+0x30958): Section mismatch in reference from the variable rx51_si4713_dev to the (unknown reference) .init.data:(unknown)
The variable rx51_si4713_dev references
the (unknown reference) __initdata (unknown)
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
Reported-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
memblock_steal tries to reserve physical memory during boot.
When the requested size is not aligned on the section size
then, the remaining memory available for lowmem becomes
unaligned on the section boundary. There is a issue with this,
which is discussed in the thread below.
https://lkml.org/lkml/2012/6/28/112
The final conclusion from the thread seems to
be align the memblock_steal calls on the SECTION boundary.
The issue comes out when LPAE is enabled, where the
section size is 2MB.
Boot tested this on OMAP5 evm with and without LPAE.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
read_persistent_clock uses a global variable, use a spinlock to
ensure non-atomic updates to the variable don't overlap and cause
time to move backwards.
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch implements DMA support into mxs-i2c. DMA transfers are now enabled
via DT. The DMA operation is enabled by default.
Signed-off-by: Marek Vasut <marex@denx.de>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
[wsa: rebased to 3.6-rc7]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJQX7MuAAoJEHm+PkMAQRiG0h0IAJURkrMCAQUxA+Ik66ReH89s
LQcVd0U9uL4UUOi7f5WR64Vf9Cfu6VVGX9ZKSvjpNskvlQaUQPMIt4pMe6g4X4dI
u0bApEy4XZz3nGabUAghIU8jJ8cDmhCG6kPpSiS7pi7KHc0yIa4WFtJRrIpGaIWT
xuK38YOiOHcSDRlLyWZzainMncQp/ixJdxnqVMTonkVLk0q0b84XzOr4/qlLE5lU
i+TsK3PRKdQXgvZ4CebL+srPBwWX1dmgP3VkeBloQbSSenSeELICbFWavn2ml+sF
GXi4dO93oNquL/Oy5SwI666T4uNcrRPaS+5X+xSZgBW/y2aQVJVJuNZg6ZP/uWk=
=0v2l
-----END PGP SIGNATURE-----
Merge tag 'v3.6-rc7' into i2c-embedded/for-next
Linux 3.6-rc7
Needed to get updates from i2c-embedded/for-current into i2c-embedded/for-next
This removes a build-time warning in uncompress.h due to incorrectly
cast values being passed to readb/writeb.
Removed arm/io.h and readb/writeb. Read/write directly to the serial
port with a volatile pointer.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Olof Johansson <olof@lixom.net>
This adds simple DT bindings for SDHCI SPEAr controller. It uses cd-gpios
from common mmc bindings.
This also fixes spear300-evb.dts with correct name for card detect binding.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This time the IOMMU updates contain a bunch of fixes and cleanups to
various IOMMU drivers and the DMA debug code. New features are the
code for IRQ remapping support with the AMD IOMMU (preperation for that
was already merged in the last release) and a debugfs interface to
export some statistics in the NVidia Tegra IOMMU driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIbBAABAgAGBQJQbvi2AAoJECvwRC2XARrjIOcP92esm3auz49N2+rq5TAto6hX
4MbpUFgkpKQRdFUSgYOsuzjh+I46ZpWEVajCxM+9oJz4I3PalDH0hvN7VkcZTjvR
bENRaLOZNR39rtIPrNVlne2RX7DXjKxJF5+K7jD6uMGJdItPfXk1Vo0VrLw30+XD
E3pWNFCS+qJkWl7d0UGUJ6CzS1BZuHZdAx+XdHTa9DIV88jANiUefIV35cAVuqrL
xVDDDMs7ITIYn6vTpEj7/zXCHNcFS7Ki4FQxAQ4DFvpPdrvLtPMeXnVSBMg0LPpe
Gb2r8tjywo83yjZMoDxca6w20SJPkQHoWwlansGlg5j0KwqPhvD1M/OXwzbq6avd
fqL69kZTXttLY+qtnlM5YfAqySXevGmGusgmqEXT7GvbAH6dSqMDdPU2W6lt4zBd
80LyAdcwP5X5hT91KiOfGGpFY4np97dUC7QFbwAdgDO7t6R+c2OfSte6azzWkYm4
2eYCsIKy+5U6XLSNabp7QNAxnic3mt6/AVMydZsVLyjeQZ8ybCwslQjPxSNwQrxc
bx8z8KFY37UuFUs77dYFIChM8BJP6erKL0W1BOt0Ve2PWgeOaEl3y5n3mwBe+GXa
JU9SPqy0juNZIYJWU1ZE/90ULo6ZpB3wM7QpMgX1pJ7KTd1gYDjSXhAEJi5Eje8r
GNHlYwjxsQZQcvR19g8=
=Q5kj
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v3.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
"This time the IOMMU updates contain a bunch of fixes and cleanups to
various IOMMU drivers and the DMA debug code. New features are the
code for IRQ remapping support with the AMD IOMMU (preperation for
that was already merged in the last release) and a debugfs interface
to export some statistics in the NVidia Tegra IOMMU driver."
* tag 'iommu-updates-v3.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (27 commits)
iommu/amd: Remove obsolete comment line
dma-debug: Remove local BUS_NOTIFY_UNBOUND_DRIVER define
iommu/amd: Fix possible use after free in get_irq_table()
iommu/amd: Report irq remapping through IOMMU-API
iommu/amd: Print message to system log when irq remapping is enabled
iommu/irq: Use amd_iommu_irq_ops if supported
iommu/amd: Make sure irq remapping still works on dma init failure
iommu/amd: Add initialization routines for AMD interrupt remapping
iommu/amd: Add call-back routine for HPET MSI
iommu/amd: Implement MSI routines for interrupt remapping
iommu/amd: Add IOAPIC remapping routines
iommu/amd: Add routines to manage irq remapping tables
iommu/amd: Add IRTE invalidation routine
iommu/amd: Make sure IOMMU is not considered to translate itself
iommu/amd: Split device table initialization into irq and dma part
iommu/amd: Check if IOAPIC information is correct
iommu/amd: Allocate data structures to keep track of irq remapping tables
iommu/amd: Add slab-cache for irq remapping tables
iommu/amd: Keep track of HPET and IOAPIC device ids
iommu/amd: Fix features reporting
...
Commit e54adb1e79 ("ARM: OMAP: omap3evm:
cleanup revision bits") adds a new sparse[1] warning:
arch/arm/mach-omap2/board-omap3evm.c:90:4: warning: symbol 'get_omap3_evm_rev' was not declared. Should it be static?
This symbol no longer appears to be used outside this file, so mark it
static and remove the export.
...
1. https://sparse.wiki.kernel.org/index.php/Main_Page
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tony Lindgren <tony@atomide.com>
Commit 7d7e1eb (ARM: OMAP2+: Prepare for irqs.h removal) and commit ec2c082
(ARM: OMAP2+: Remove hardcoded IRQs and enable SPARSE_IRQ) updated the way
interrupts for OMAP2/3 devices are defined in the HWMOD data structures to
being an index plus a fixed offset (defined by OMAP_INTC_START). The definition
of the PMU interrupts on OMAP2/3 devices is missing the OMAP_INTC_START offset
and so this is causing the allocation of PMU interrupts to fail on OMAP2/3
devices. So add the offset to fix this.
This is patch is based upon Tony's master branch for OMAP.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
After Rajendra's common-clock preparation series,
commit (a1978ef4da1 - ARM: omap: hwmod: get rid of
all omap_clk_get_by_name usage) the clkdev table need to
update with an entry for clocks used by hwmod to have
clock name same as the alias.
Without this, the clk_get() in omap_hwmod would fail.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
We already have CONFIG_ARCH_MXC cover imx5 and imx6 dtb targets.
Remove the redundant ones with CONFIG_ARCH_IMX5 and CONFIG_SOC_IMX6Q.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
This is a series from Arnd that fixes a number of compiler warnings
when building defconfigs on ARM.
* late/fixes:
ARM: footbridge: nw_gpio_lock is raw_spin_lock
ARM: mv78xx0: correct addr_map_cfg __initdata annotation
ARM: footbridge: remove RTC_IRQ definition
ARM: soc: dependency warnings for errata
ARM: ks8695: __arch_virt_to_dma type handling
ARM: rpc: check device_register return code in ecard_probe
ARM: davinci: don't mark da850_register_cpufreq as __init
ARM: iop13xx: fix iq81340sc_atux_map_irq prototype
ARM: iop13xx: mark iop13xx_scan_bus as __devinit
ARM: mv78xx0: mark mv78xx0_timer_init as __init_refok
ARM: s3c24xx: fix multiple section mismatch warnings
ARM: at91: unused variable in at91_pm_verify_clocks
ARM: at91: skip at91_io_desc definition for NOMMU
ARM: pxa: work around duplicate definition of GPIO24_SSP1_SFRM
ARM: pxa: remove sharpsl_fatal_check function
ARM: pxa: define palmte2_pxa_keys conditionally
ARM: pxa: Wunused-result warning in viper board file
ARM: shark: fix shark_pci_init return code
Fixed trivial conflicts in arch/arm/mach-at91/setup.c.
Signed-off-by: Olof Johansson <olof@lixom.net>
Check for framebuffer defines before declaring variables in vt8500.c
Removes a compile-time warning about unused variables.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add board files (vt8500-bv07, wm8505-ref and wm8650-mid)
to allow 'make dtbs' on arch-vt8500.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Olof Johansson <olof@lixom.net>
Since the complete conversion to device tree, there are no board-
specific Kconfig options left, so remove the useless Kconfig entry.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
Unit addresses, whilst written in hex, don't contain a 0x prefix.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
I mismerged one of the branches that moves around gpio header file usage,
and messed up for IOP. This fixes the obvious compilation failures caused
by it.
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull ARM updates from Russell King:
"This is the first chunk of ARM updates for this merge window.
Conflicts are expected in two files - asm/timex.h and
mach-integrator/integrator_cp.c. Nothing particularly stands out more
than anything else.
Most of the growth is down to the opcodes stuff from Dave Martin,
which is countered by Rob's patches to use more of the asm-generic
headers on ARM."
(A few more conflicts grew since then, but it all looked fairly trivial)
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm: (44 commits)
ARM: 7548/1: include linux/sched.h in syscall.h
ARM: 7541/1: Add ARM ERRATA 775420 workaround
ARM: ensure vm_struct has its phys_addr member filled in
ARM: 7540/1: kexec: Check segment memory addresses
ARM: 7539/1: kexec: scan for dtb magic in segments
ARM: 7538/1: delay: add registration mechanism for delay timer sources
ARM: 7536/1: smp: Formalize an IPI for wakeup
ARM: 7525/1: ptrace: use updated syscall number for syscall auditing
ARM: 7524/1: support syscall tracing
ARM: 7519/1: integrator: convert platform devices to Device Tree
ARM: 7518/1: integrator: convert AMBA devices to device tree
ARM: 7517/1: integrator: initial device tree support
ARM: 7516/1: plat-versatile: add DT support to FPGA IRQ
ARM: 7515/1: integrator: check PL010 base address from resource
ARM: 7514/1: integrator: call common init function from machine
ARM: 7522/1: arch_timers: register a time/cycle counter
ARM: 7523/1: arch_timers: enable the use of the virtual timer
ARM: 7531/1: mark kernelmode mem{cpy,set} non-experimental
ARM: 7520/1: Build dtb files in all target
ARM: Fix build warning in arch/arm/mm/alignment.c
...
This branch contains updates to OMAP and Marvell platforms (kirkwood,
dove, mvebu) that came in after we had done the big multiplatform merges,
so they were kept separate from the rest, and not separated into the
traditional topics of cleanup/driver/platform features.
For OMAP, the updates are:
- Runtime PM conversions for the GPMC and RNG IP blocks
- Preparation patches for the OMAP common clock framework conversion
- clkdev alias additions required by other drivers
- Performance Monitoring Unit (PMU) support for OMAP2, 3, and non-4430 OMAP4
- OMAP hwmod code and data improvements
- Preparation patches for the IOMMU runtime PM conversion
- Preparation patches for OMAP4 full-chip retention support
For Kirkwood/Dove/mvebu:
- New driver for "address decoder controller" for mvebu, which
is a piece of hardware that configures addressable devices and
peripherals. First user is the boot rom aperture on armada XP since
it is needed for SMP support.
- New device tree bindings for peripherals such as gpio-fan, iconnect
nand, mv_cesa and the above address decoder controller.
- Some defconfig updates, mostly to enable new DT boards and a few drivers.
- New drivers using the pincontrol subsystem for dove, kirkwood and mvebu
- New clean gpio driver for mvebu
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=xVaJ
-----END PGP SIGNATURE-----
Merge tag 'soc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull late ARM soc platform updates from Olof Johansson:
"This branch contains updates to OMAP and Marvell platforms (kirkwood,
dove, mvebu) that came in after we had done the big multiplatform
merges, so they were kept separate from the rest, and not separated
into the traditional topics of cleanup/driver/platform features.
For OMAP, the updates are:
- Runtime PM conversions for the GPMC and RNG IP blocks
- Preparation patches for the OMAP common clock framework conversion
- clkdev alias additions required by other drivers
- Performance Monitoring Unit (PMU) support for OMAP2, 3, and
non-4430 OMAP4
- OMAP hwmod code and data improvements
- Preparation patches for the IOMMU runtime PM conversion
- Preparation patches for OMAP4 full-chip retention support
For Kirkwood/Dove/mvebu:
- New driver for "address decoder controller" for mvebu, which is a
piece of hardware that configures addressable devices and
peripherals. First user is the boot rom aperture on armada XP
since it is needed for SMP support.
- New device tree bindings for peripherals such as gpio-fan, iconnect
nand, mv_cesa and the above address decoder controller.
- Some defconfig updates, mostly to enable new DT boards and a few
drivers.
- New drivers using the pincontrol subsystem for dove, kirkwood and
mvebu
- New clean gpio driver for mvebu"
* tag 'soc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (98 commits)
ARM: mvebu: fix build breaks from multi-platform conversion
ARM: OMAP4460/4470: PMU: Enable PMU for OMAP4460/70
ARM: OMAP2+: PMU: Add runtime PM support
ARM: OMAP4430: PMU: prepare to create PMU device via HWMOD
ARM: OMAP2+: PMU: Convert OMAP2/3 devices to use HWMOD
ARM: OMAP3: hwmod data: Add debugss HWMOD data
ARM: OMAP2+: clockdomain/hwmod: add workaround for EMU clockdomain idle problems
ARM: OMAP: Add a timer attribute for timers that can interrupt the DSP
hwrng: OMAP: remove SoC restrictions from driver registration
ARM: OMAP: split OMAP1, OMAP2+ RNG device registration
hwrng: OMAP: convert to use runtime PM
hwrng: OMAP: store per-device data in per-device variables, not file statics
ARM: OMAP2xxx: hwmod/CM: add RNG integration data
ARM: OMAP2+: gpmc: minimal driver support
ARM: OMAP2+: gpmc: Adapt to HWMOD
ARM: OMAP2/3: hwmod data: add gpmc
ARM: OMAP4: hwmod data: add mmu hwmod for ipu and dsp
ARM: OMAP3: hwmod data: add mmu data for iva and isp
ARM: OMAP: iommu: fix including iommu.h without IOMMU_API selected
ARM: OMAP4: hwmod data: add missing HWMOD_NO_IDLEST flags to some PRCM IP blocks
...
This might be the last time we do a standalone defconfig branch,
since we now prefer to get them with the rest of the subarch updates
instead. These add a handful of useful options on various platforms,
enable new boards and SoCs, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=+zKc
-----END PGP SIGNATURE-----
Merge tag 'defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc defconfig updates from Olof Johansson:
"This might be the last time we do a standalone defconfig branch, since
we now prefer to get them with the rest of the subarch updates
instead. These add a handful of useful options on various platforms,
enable new boards and SoCs, etc."
* tag 'defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: tegra: defconfig updates
ARM: LPC32xx: Defconfig update
ARM: mach-shmobile: marzen: defconfig update
ARM: mxs_defconfig: Add SPI and LRADC support
ARM: s3c6400_defconfig: enable more boards in defconfig
ARM: imx_v6_v7_defconfig: Remove CONFIG_DEFAULT_MMAP_MIN_ADDR
ARM: imx_v6_v7_defconfig: Add Chipidea USB driver support
ARM: mxs_defconfig: Add framebuffer support
ARM: mxs_defconfig: Add LED, PWM and MTD_CHAR support
ARM: mxs_defconfig: Enable USB host
Pull media updates from Mauro Carvalho Chehab:
"The first part of the media updates for Kernel 3.7.
This series contain:
- A major tree renaming patch series: now, drivers are organized
internally by their used bus, instead of by V4L2 and/or DVB API,
providing a cleaner driver location for hybrid drivers that
implement both APIs, and allowing to cleanup the Kconfig items and
make them more intuitive for the end user;
- Media Kernel developers are typically very lazy with their duties
of keeping the MAINTAINERS entries for their drivers updated. As
now the tree is more organized, we're doing an effort to add/update
those entries for the drivers that aren't currently orphan;
- Several DVB USB drivers got moved to a new DVB USB v2 core; the new
core fixes several bugs (as the existing one that got bitroted).
Now, suspend/resume finally started to work fine (at least with
some devices - we should expect more work with regards to it);
- added multistream support for DVB-T2, and unified the API for
DVB-S2 and ISDB-S. Backward binary support is preserved;
- as usual, a few new drivers, some V4L2 core improvements and lots
of drivers improvements and fixes.
There are some points to notice on this series:
1) you should expect a trivial merge conflict on your tree, with the
removal of Documentation/feature-removal-schedule.txt: this series
would be adding two additional entries there. I opted to not
rebase it due to this recent change;
2) With regards to the PCTV 520e udev-related breakage, I opted to
fix it in a way that the patches can be backported to 3.5 even
without your firmware fix patch. This way, Greg doesn't need to
rush backporting your patch (as there are still the firmware cache
and firmware path customization issues to be addressed there).
I'll send later a patch (likely after the end of the merge window)
reverting the rest of the DRX-K async firmware request, fully
restoring its original behaviour to allow media drivers to
initialize everything serialized as before for 3.7 and upper.
3) I'm planning to work on this weekend to test the DMABUF patches
for V4L2. The patches are on my queue for several Kernel cycles,
but, up to now, there is/was no way to test the series locally.
I have some concerns about this particular changeset with regards
to security issues, and with regards to the replacement of the old
VIDIOC_OVERLAY ioctl's that is broken on modern systems, due to
GPU drivers change. The Overlay API allows direct PCI2PCI
transfers from a media capture card into the GPU framebuffer, but
its API is crappy. Also, the only existing X11 driver that
implements it requires a XV extension that is not available
anymore on modern drivers. The DMABUF can do the same thing, but
with it is promising to be a properly-designed API. If I can
successfully test this series and be happy with it, I should be
asking you to pull them next week."
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (717 commits)
em28xx: regression fix: use DRX-K sync firmware requests on em28xx
drxk: allow loading firmware synchrousnously
em28xx: Make all em28xx extensions to be initialized asynchronously
[media] tda18271: properly report read errors in tda18271_get_id
[media] tda18271: delay IR & RF calibration until init() if delay_cal is set
[media] MAINTAINERS: add Michael Krufky as tda827x maintainer
[media] MAINTAINERS: add Michael Krufky as tda8290 maintainer
[media] MAINTAINERS: add Michael Krufky as cxusb maintainer
[media] MAINTAINERS: add Michael Krufky as lg2160 maintainer
[media] MAINTAINERS: add Michael Krufky as lgdt3305 maintainer
[media] MAINTAINERS: add Michael Krufky as mxl111sf maintainer
[media] MAINTAINERS: add Michael Krufky as mxl5007t maintainer
[media] MAINTAINERS: add Michael Krufky as tda18271 maintainer
[media] s5p-tv: Report only multi-plane capabilities in vidioc_querycap
[media] s5p-mfc: Fix misplaced return statement in s5p_mfc_suspend()
[media] exynos-gsc: Add missing static storage class specifiers
[media] exynos-gsc: Remove <linux/version.h> header file inclusion
[media] s5p-fimc: Fix incorrect condition in fimc_lite_reqbufs()
[media] s5p-tv: Fix potential NULL pointer dereference error
[media] s5k6aa: Fix possible NULL pointer dereference
...
The annotation on the addr_map_cfg variable is in the wrong place.
Without this patch, building mv78xx0_defconfig results in:
/home/arnd/linux-arm/arch/arm/mach-mv78xx0/addr-map.c:59:2: warning: initialization from incompatible pointer type [enabled by default]
/home/arnd/linux-arm/arch/arm/mach-mv78xx0/addr-map.c:59:2: warning: (near initialization for 'addr_map_cfg.win_cfg_base') [enabled by default]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Cc: Jason Cooper <jason@lakedaemon.net>
Since commit bd8abc9a32 "ARM: mc146818rtc: remove unnecessary include of
mach/irqs.h", building footbridge_defconfig results in this warning:
In file included from include/linux/mc146818rtc.h:16:0,
from arch/arm/mach-footbridge/isa-rtc.c:21:
arch/arm/include/asm/mc146818rtc.h:10:0: warning: "RTC_IRQ" redefined [enabled by default]
arch/arm/mach-footbridge/include/mach/irqs.h:93:0: note: this is the location of the previous definition
The above commit was intentionally made to catch errors like this,
where code relies on the RTC_IRQ definition. The only driver using
it is the legacy PC-style drivers/char/rtc.c driver.
However, the ARM architecture has been using the RTC_LIB framework
since at least 2006, and that doesn't use it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: rtc-linux@googlegroups.com
Cc: Russell King <linux@arm.linux.org.uk>
The PL310_ERRATA_753970 and ARM_ERRATA_764369 symbols only make sense
when the base features for them are enabled, so select them
conditionally in Kconfig to avoid warnings like:
warning: (UX500_SOC_COMMON) selects PL310_ERRATA_753970 which has unmet direct dependencies (CACHE_PL310)
warning: (ARCH_TEGRA_2x_SOC && ARCH_TEGRA_3x_SOC && UX500_SOC_COMMON) selects ARM_ERRATA_764369 which has unmet direct dependencies (CPU_V7 && SMP)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
__arch_virt_to_dma expects a virtual address pointer, but
the ks8695 implementation of this macro treats it as an
integer. Adding a type cast avoids hundreds of identical
warning messages.
Without this patch, building acs5k_defconfig results in:
arch/arm/include/asm/dma-mapping.h: In function 'virt_to_dma':
arch/arm/include/asm/dma-mapping.h:60:2: warning: passing argument 1 of '__virt_to_phys' makes integer from pointer without a cast [enabled by default]
arch/arm/include/asm/memory.h:172:60: note: expected 'long unsigned int' but argument is of type 'void *'
In file included from include/linux/dma-mapping.h:73:0,
from include/linux/skbuff.h:33,
from security/commoncap.c:21:
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Cc: Daniel Silverstone <dsilvers@simtec.co.uk>
Cc: Ben Dooks <ben-linux@fluff.org>
device_register is marked __must_check, so we better propagate the error
value by returning it from ecard_probe.
Without this patch, building rpc_defconfig results in:
arch/arm/mach-rpc/ecard.c: In function 'ecard_probe':
arch/arm/mach-rpc/ecard.c:963:17: warning: ignoring return value of 'device_register', declared with attribute warn_unused_result [-Wunused-result]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
The mityomapl138_cpufreq_init and read_factory_config function in
board-mityomapl138.c are not __init functions and might be called
at a later stage, so da850_register_cpufreq must not be __init either.
Without this patch, building da8xx_omapl_defconfig results in:
WARNING: arch/arm/mach-davinci/built-in.o(.text+0x2eb4): Section mismatch in reference from the function read_factory_config() to the function .init.text:da850_register_cpufreq()
The function read_factory_config() references
the function __init da850_register_cpufreq().
This is often because read_factory_config lacks a __init
annotation or the annotation of da850_register_cpufreq is wrong.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
The pci map_irq callbacks get a 'const' pci_dev argument, so change the
iop13xx version to use the same prototype as everything else.
Without this patch, building iop13xx_defconfig results in:
arch/arm/mach-iop13xx/iq81340sc.c:63:2: warning: initialization from incompatible pointer type [enabled by default]
arch/arm/mach-iop13xx/iq81340sc.c:63:2: warning: (near initialization for 'iq81340sc_pci.map_irq') [enabled by default]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Dan Williams <djbw@fb.com>
pci_scan_root_bus is __devinit, so iop13xx_scan_bus has to be the
same in order to safely call it. This is ok because the function
itself is only called from the hwpci->scan callback.
WARNING: vmlinux.o(.text+0x10138): Section mismatch in reference from the function iop13xx_scan_bus() to the function .devinit.text:pci_scan_root_bus()
The function iop13xx_scan_bus() references
the function __devinit pci_scan_root_bus().
This is often because iop13xx_scan_bus lacks a __devinit
annotation or the annotation of pci_scan_root_bus is wrong.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Dan Williams <djbw@fb.com>
The sys_timer init function is only called at __init time,
so it's safe to mark mv78xx0_timer_init as __init_refok,
which allows us to call orion_time_init without getting
a link time warning.
Without this patch, building mv78xx0_defconfig results in:
WARNING: vmlinux.o(.text+0x15470): Section mismatch in reference from the function mv78xx0_timer_init() to the function .init.text:orion_time_init()
The function mv78xx0_timer_init() references
the function __init orion_time_init().
This is often because mv78xx0_timer_init lacks a __init
annotation or the annotation of orion_time_init is wrong.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
The *_irq_add function should not be marked __init because the driver
subsystem thinks they might be called at a later stage.
The usb_simtec_init function accesses initdata and should be marked
init. This is safe because the only caller is also an init function.
Without this patch, building s3c2410_defconfig results in:
WARNING: arch/arm/mach-s3c24xx/built-in.o(.data+0x1030): Section mismatch in reference from the variable s3c2416_irq_interface to the function .init.text:s3c2416_irq_add()
The variable s3c2416_irq_interface references
the function __init s3c2416_irq_add()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
WARNING: arch/arm/mach-s3c24xx/built-in.o(.data+0x1b08): Section mismatch in reference from the variable s3c2443_irq_interface to the function .init.text:s3c2443_irq_add()
The variable s3c2443_irq_interface references
the function __init s3c2443_irq_add()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
WARNING: arch/arm/mach-s3c24xx/built-in.o(.data+0xf44): Section mismatch in reference from the variable s3c2416_irq_interface to the function .init.text:s3c2416_irq_add()
The variable s3c2416_irq_interface references
the function __init s3c2416_irq_add()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
WARNING: arch/arm/mach-s3c24xx/built-in.o(.text+0x3f7c): Section mismatch in reference from the function usb_simtec_init() to the (unknown reference) .init.data:(unknown)
The function usb_simtec_init() references
the (unknown reference) __initdata (unknown).
This is often because usb_simtec_init lacks a __initdata
annotation or the annotation of (unknown) is wrong.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
* Allow a Linux guest to boot as initial domain and as normal guests
on Xen on ARM (specifically ARMv7 with virtualized extensions).
PV console, block and network frontend/backends are working.
Bug-fixes:
* Fix compile linux-next fallout.
* Fix PVHVM bootup crashing.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJQbJELAAoJEFjIrFwIi8fJSI4H/32qrQKyF5IIkFKHTN9FYDC1
OxEGc4y47DIQpGUd/PgZ/i6h9Iyhj+I6pb4lCevykwgd0j83noepluZlCIcJnTfL
HVXNiRIQKqFhqKdjTANxVM4APup+7Lqrvqj6OZfUuoxaZ3tSTLhabJ/7UXf2+9xy
g2RfZtbSdQ1sukQ/A2MeGQNT79rh7v7PrYQUYSrqytjSjSLPTqRf75HWQ+eapIAH
X3aVz8Tn6nTixZWvZOK7rAaD4awsFxGP6E46oFekB02f4x9nWHJiCZiXwb35lORb
tz9F9td99f6N4fPJ9LgcYTaCPwzVnceZKqE9hGfip4uT+0WrEqDxq8QmBqI5YtI=
=gxJD
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.7-arm-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull ADM Xen support from Konrad Rzeszutek Wilk:
Features:
* Allow a Linux guest to boot as initial domain and as normal guests
on Xen on ARM (specifically ARMv7 with virtualized extensions). PV
console, block and network frontend/backends are working.
Bug-fixes:
* Fix compile linux-next fallout.
* Fix PVHVM bootup crashing.
The Xen-unstable hypervisor (so will be 4.3 in a ~6 months), supports
ARMv7 platforms.
The goal in implementing this architecture is to exploit the hardware
as much as possible. That means use as little as possible of PV
operations (so no PV MMU) - and use existing PV drivers for I/Os
(network, block, console, etc). This is similar to how PVHVM guests
operate in X86 platform nowadays - except that on ARM there is no need
for QEMU. The end result is that we share a lot of the generic Xen
drivers and infrastructure.
Details on how to compile/boot/etc are available at this Wiki:
http://wiki.xen.org/wiki/Xen_ARMv7_with_Virtualization_Extensions
and this blog has links to a technical discussion/presentations on the
overall architecture:
http://blog.xen.org/index.php/2012/09/21/xensummit-sessions-new-pvh-virtualisation-mode-for-arm-cortex-a15arm-servers-and-x86/
* tag 'stable/for-linus-3.7-arm-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen: (21 commits)
xen/xen_initial_domain: check that xen_start_info is initialized
xen: mark xen_init_IRQ __init
xen/Makefile: fix dom-y build
arm: introduce a DTS for Xen unprivileged virtual machines
MAINTAINERS: add myself as Xen ARM maintainer
xen/arm: compile netback
xen/arm: compile blkfront and blkback
xen/arm: implement alloc/free_xenballooned_pages with alloc_pages/kfree
xen/arm: receive Xen events on ARM
xen/arm: initialize grant_table on ARM
xen/arm: get privilege status
xen/arm: introduce CONFIG_XEN on ARM
xen: do not compile manage, balloon, pci, acpi, pcpu and cpu_hotplug on ARM
xen/arm: Introduce xen_ulong_t for unsigned long
xen/arm: Xen detection and shared_info page mapping
docs: Xen ARM DT bindings
xen/arm: empty implementation of grant_table arch specific functions
xen/arm: sync_bitops
xen/arm: page.h definitions
xen/arm: hypercalls
...
A couple more updates for 3.7, enhancements to the ux500 and wm2000
drivers, a new driver for DA9055 and the support for regulator bypass
mode. With the exception of the DA9055 this has all had a chance to
soak in -next (the driver was added on Friday so should be in -next
today).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=nHb7
-----END PGP SIGNATURE-----
Merge tag 'asoc-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Additional updates for v3.7
A couple more updates for 3.7, enhancements to the ux500 and wm2000
drivers, a new driver for DA9055 and the support for regulator bypass
mode. With the exception of the DA9055 this has all had a chance to
soak in -next (the driver was added on Friday so should be in -next
today).
Convert the driver from the outdated omap_pm_set_max_mpu_wakeup_lat
API to the new PM QoS API.
Since the constraint is on the MPU subsystem, use the PM_QOS_CPU_DMA_LATENCY
class of PM QoS. The resulting MPU constraints are used by cpuidle to
decide the next power state of the MPU subsystem.
The I2C device latency timing is derived from the FIFO size and the
clock speed and so is applicable to all OMAP SoCs.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Acked-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Rename MIPI-CSIS regulator supply names to match definitions in
the driver after commit "s5p-csis: Change regulator supply names".
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Replace pdev argument __s5p_mipi_phy_control() helper with plain int
so MIPI-CSIS hardware instance index can be passed directly making
the function usable on platforms instantiated from device tree.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The MIPI-CSI2 bus data alignment is now being derived from the media
bus pixel code, the drivers don't use the corresponding structure
fields, so remove them. Also remove the s5p_csis_phy_enable callback
which is now used directly by s5p-csis driver.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
vpif_display relied on a 1-1 mapping of output and subdev. This is not
necessarily the case. Separate the two. So there is a list of subdevs
and a list of outputs. Each output refers to a subdev and has routing
information. An output does not have to have a subdev.
The initial output for each channel is set to the fist output.
Currently missing is support for associating multiple subdevs with
an output.
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
struct vpif_interface is channel specific, not subdev specific.
Move it to the channel config.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Tested-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Routing information is a property of the input, not of the subdev.
One subdev may provide multiple inputs, each with its own routing
information.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Tested-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Calling a subdev op that isn't implemented will just return -ENOIOCTLCMD
No need to have a flag for that.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Tested-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Include the expander settings to select VPIF peripheral on
UI card and add registration call in EVM init. Also add platform
data to configure display and capture devices.
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Merge misc patches from Andrew Morton:
"The MM tree is rather stuck while I wait to find out what the heck is
happening with sched/numa. Probably I'll need to route around all the
code which was added to -next, sigh.
So this is "everything else", or at least most of it - other small
bits are still awaiting resolutions of various kinds."
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (180 commits)
lib/decompress.c add __init to decompress_method and data
kernel/resource.c: fix stack overflow in __reserve_region_with_split()
omfs: convert to use beXX_add_cpu()
taskstats: cgroupstats_user_cmd() may leak on error
aoe: update aoe-internal version number to 50
aoe: update documentation to better reflect aoe-plus-udev usage
aoe: remove unused code
aoe: make dynamic block minor numbers the default
aoe: update and specify AoE address guards and error messages
aoe: retain static block device numbers for backwards compatibility
aoe: support more AoE addresses with dynamic block device minor numbers
aoe: update documentation with new URL and VM settings reference
aoe: update copyright year in touched files
aoe: update internal version number to 49
aoe: remove unused code and add cosmetic improvements
aoe: increase net_device reference count while using it
aoe: associate frames with the AoE storage target
aoe: disallow unsupported AoE minor addresses
aoe: do revalidation steps in order
aoe: failover remote interface based on aoe_deadsecs parameter
...
This patch replaces V4L2_OUT_CAP_CUSTOM_TIMINGS macro with
V4L2_OUT_CAP_DV_TIMINGS. As V4L2_OUT_CAP_CUSTOM_TIMINGS is being phased
out.
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch replaces the preset API by the timings API, and
appropriate changes in board file.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The syscall tracing patch introduces a compile bug in lttng-modules
when the latter calls syscall_get_nr(), similar to the following:
<path-to-linux>/arch/arm/include/asm/syscall.h:21:2: error: implicit declaration of function 'task_thread_info' [-Werror=implicit-function-declaration]
The issue is that we are using task_thread_info() in the
syscall_get_nr() function in asm/syscall.h, but not explicitly
including sched.h from this file, so we can expect this bug might
surface any time that syscall_get_nr() is called.
Explicitly including sched.h solves the problem.
Cc: <stable@vger.kernel.org> [3.5, 3.6]
Signed-off-by: Wade Farnsworth <wade_farnsworth@mentor.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Merge in the late Kirkwood branch with the OMAP late branch for upstream
submission.
Final contents described in shared tag.
Fixup remove/change conflicts in arch/arm/mach-omap2/devices.c and
drivers/spi/spi-omap2-mcspi.c.
Signed-off-by: Olof Johansson <olof@lixom.net>
As usual we have a few new drivers:
- TI LP8788
- TI OMAP USB TLL
- Maxim MAX8907
- SMSC ECE1099
- Dialog Semiconductor DA9055
- A simpler syscon driver that allow us to get rid of the anatop one.
Drivers are also gradually getting Device Tree and IRQ domain support.
The following drivers got DT support:
- palmas, 88pm860x, tc3589x and twl4030-audio
And those ones now use the IRQ domain APIs:
- 88pm860x, tc3589x, db8500_prcmu
Also some other interesting changes:
- Intel's ICH LPC now supports Lynx Point
- TI's twl4030-audio added a GPO child
- tps6527 enabled its backlight subdevice
- The twl6030 pwm driver moved to the new PWM subsystem
And finally a bunch of cleanup and casual fixes for mc13xxx, 88pm860x, palmas,
ab8500, wm8994, wm5110, max8907 and the tps65xxx family.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=n6lp
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFD changes from Samuel Ortiz:
"MFD bits for the 3.7 merge window.
As usual we have a few new drivers:
- TI LP8788
- TI OMAP USB TLL
- Maxim MAX8907
- SMSC ECE1099
- Dialog Semiconductor DA9055
- A simpler syscon driver that allow us to get rid of the anatop one.
Drivers are also gradually getting Device Tree and IRQ domain support.
The following drivers got DT support:
- palmas, 88pm860x, tc3589x and twl4030-audio
And those ones now use the IRQ domain APIs:
- 88pm860x, tc3589x, db8500_prcmu
Also some other interesting changes:
- Intel's ICH LPC now supports Lynx Point
- TI's twl4030-audio added a GPO child
- tps6527 enabled its backlight subdevice
- The twl6030 pwm driver moved to the new PWM subsystem
And finally a bunch of cleanup and casual fixes for mc13xxx, 88pm860x,
palmas, ab8500, wm8994, wm5110, max8907 and the tps65xxx family."
Fix up various annoying conflicts: the DT and IRQ domain support came in
twice and was already in 3.6. And then it was apparently rebased.
Guys, DON'T REBASE!
* tag 'mfd-3.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (89 commits)
ARM: dts: Enable 88pm860x pmic
mfd: 88pm860x: Move gpadc init into touch
mfd: 88pm860x: Device tree support
mfd: 88pm860x: Use irqdomain
mfd: smsc: Add support for smsc gpio io/keypad driver
backlight: tps65217_bl: Add missing platform_set_drvdata in tps65217_bl_probe
mfd: DA9055 core driver
mfd: tps65910: Add alarm interrupt of TPS65910 RTC to mfd device list
mfd: wm5110: Add register patches for revision B
mfd: wm5110: Disable control interface error report for WM5110 rev B
mfd: max8907: Remove regulator-compatible from DT docs
backlight: Add TPS65217 WLED driver
mfd: Add backlight as subdevice to the tps65217
mfd: Provide the PRCMU with its own IRQ domain
mfd: Fix max8907 sparse warning
mfd: Add lp8788 mfd driver
mfd: dbx500: Provide a more accurate smp_twd clock
mfd: rc5t583: Fix warning messages
regulator: palmas: Add DT support
mfd: palmas: Change regulator defns to better suite DT
...
The old method of registering with the ASoC core by creating a
"soc-audio" platform device no longer works for Amstrad Delta sound card
after recent changes to drvdata handling (commit
0998d06310, 'device-core: Ensure drvdata =
NULL when no driver is bound'.
Use snd_soc_register_card() method instead, as suggested by the ASoC
core generated warning message, and move both the card and codec
platform device registration to the arch board file where those belong.
Created and tested against linux-3.6-rc5.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Pull crypto update from Herbert Xu:
- Optimised AES/SHA1 for ARM.
- IPsec ESN support in talitos and caam.
- x86_64/avx implementation of cast5/cast6.
- Add/use multi-algorithm registration helpers where possible.
- Added IBM Power7+ in-Nest support.
- Misc fixes.
Fix up trivial conflicts in crypto/Kconfig due to the sparc64 crypto
config options being added next to the new ARM ones.
[ Side note: cut-and-paste duplicate help texts make those conflicts
harder to read than necessary, thanks to git being smart about
minimizing conflicts and maximizing the common parts... ]
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (71 commits)
crypto: x86/glue_helper - fix storing of new IV in CBC encryption
crypto: cast5/avx - fix storing of new IV in CBC encryption
crypto: tcrypt - add missing tests for camellia and ghash
crypto: testmgr - make test_aead also test 'dst != src' code paths
crypto: testmgr - make test_skcipher also test 'dst != src' code paths
crypto: testmgr - add test vectors for CTR mode IV increasement
crypto: testmgr - add test vectors for partial ctr(cast5) and ctr(cast6)
crypto: testmgr - allow non-multi page and multi page skcipher tests from same test template
crypto: caam - increase TRNG clocks per sample
crypto, tcrypt: remove local_bh_disable/enable() around local_irq_disable/enable()
crypto: tegra-aes - fix error return code
crypto: crypto4xx - fix error return code
crypto: hifn_795x - fix error return code
crypto: ux500 - fix error return code
crypto: caam - fix error IDs for SEC v5.x RNG4
hwrng: mxc-rnga - Access data via structure
hwrng: mxc-rnga - Adapt clocks to new i.mx clock framework
crypto: caam - add IPsec ESN support
crypto: 842 - remove .cra_list initialization
Revert "[CRYPTO] cast6: inline bloat--"
...
The code using the variable 'i' in this function is conditional which
results in a harmless compiler warning. Using the IS_ENABLED macro
instead of #ifdef makes the code look nicer and gets rid of the
warning.
Without this patch, building at91sam9263_defconfig results in:
/home/arnd/linux-arm/arch/arm/mach-at91/pm.c: In function 'at91_pm_verify_clocks':
/home/arnd/linux-arm/arch/arm/mach-at91/pm.c:137:6: warning: unused variable 'i' [-Wunused-variable]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
On NOMMU systems, we do cannot remap the MMIO space, so the
definition of at91_io_desc is unused.
Without this patch, building at91x40_defconfig results in:
arch/arm/mach-at91/setup.c:90:24: warning: 'at91_io_desc' defined but not used [-Wunused-variable]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
The symbol "GPIO24_SSP1_SFRM" is defined in both mfp-pxa27x.h and
mfp-pxa25x.h. Since the macro is not actually used in the cm-x2xx.c
file, but it includes both headers, a safe workaround should be
to just undefine it from the .c file. This is a bit hacky and
the headers should be fixed to not both define it, but for now
it gets us around an annoying warning.
Without this patch, building cm_x2xx_defconfig results in:
In file included from arch/arm/mach-pxa/include/mach-pxa/pxa27x.h:7:0,
from arch/arm/mach-pxa/cm-x2xx.c:25:
arch/arm/mach-pxa/include/mach-pxa/mfp-pxa27x.h:215:0: warning: "GPIO24_SSP1_SFRM" redefined [enabled by default]
arch/arm/mach-pxa/include/mach-pxa/mfp-pxa25x.h:111:0: note: this is the location of the previous definition
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Mike Rapoport <mike@compulab.co.il>
The sharpsl_fatal_check has not been used since Pavel Machek removed
the caller in 99f329a2b "pxa/sharpsl_pm: zaurus c3000 aka spitz: fix
resume". Nobody has complained since 2009, so it's safe to assume we
can just remove the function.
Without this patch, building corgi_defconfig results in:
/home/arnd/linux-arm/arch/arm/mach-pxa/sharpsl_pm.c:693:12: warning: 'sharpsl_fatal_check' defined but not used [-Wunused-function]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Stanislav Brabec <utx@penguin.cz>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Gcc prints a harmless warning about palmte2_pxa_keys not being used
when the gpio keyboard driver is disabled. The solution is to use
the same #ifdef that is already present in the place where the
symbol is used.
Without this patch, building palmz72_defconfig results in:
/home/arnd/linux-arm/arch/arm/mach-pxa/palmte2.c:128:31: warning: 'palmte2_pxa_keys' defined but not used [-Wunused-variable]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Carlos Eduardo Medaglia Dyonisio <cadu@nerdfeliz.com>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Calling kstrtoul requires checking the result. In case of
the viper_tpm_setup function, let's fail the __setup function
if the number was invalid.
Without this patch, building viper_defconfig results in:
arch/arm/mach-pxa/viper.c: In function 'viper_tpm_setup':
arch/arm/mach-pxa/viper.c:771:10: warning: ignoring return value of 'kstrtoul', declared with attribute warn_unused_result [-Wunused-result]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Marc Zyngier <maz@misterjones.org>
Cc: Haojian Zhuang <haojian.zhuang@marvell.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
When run on the wrong platform, the shark_pci_init function
returns an undefined value, as reported by a gcc warning,
so let's just return -ENODEV.
Without this patch, building shark_defconfig results in:
arch/arm/mach-shark/pci.c: In function 'shark_pci_init':
arch/arm/mach-shark/pci.c:42:3: warning: 'return' with no value, in function returning non-void [-Wreturn-type]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: "Krzysztof Halasa" <khc@pm.waw.pl>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=VtEQ
-----END PGP SIGNATURE-----
Merge tag 'uapi-prep-20121002' of git://git.infradead.org/users/dhowells/linux-headers
Pull preparatory patches for user API disintegration from David Howells:
"The patches herein prepare for the extraction of the Userspace API
bits from the various header files named in the Kbuild files.
New subdirectories are created under either include/uapi/ or
arch/x/include/uapi/ that correspond to the subdirectory containing
that file under include/ or arch/x/include/.
The new subdirs under the uapi/ directory are populated with Kbuild
files that mostly do nothing at this time. Further patches will
disintegrate the headers in each original directory and fill in the
Kbuild files as they do it.
These patches also:
(1) fix up #inclusions of "foo.h" rather than <foo.h>.
(2) Remove some redundant #includes from the DRM code.
(3) Make the kernel build infrastructure handle Kbuild files both in
the old places and the new UAPI place that both specify headers
to be exported.
(4) Fix some kernel tools that #include kernel headers during their
build.
I have compile tested this with allyesconfig against x86_64,
allmodconfig against i386 and a scattering of additional defconfigs of
other arches. Prepared for main script
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
Acked-by: H. Peter Anvin <hpa@zytor.com>"
* tag 'uapi-prep-20121002' of git://git.infradead.org/users/dhowells/linux-headers:
UAPI: Plumb the UAPI Kbuilds into the user header installation and checking
UAPI: x86: Differentiate the generated UAPI and internal headers
UAPI: Remove the objhdr-y export list
UAPI: Move linux/version.h
UAPI: Set up uapi/asm/Kbuild.asm
UAPI: x86: Fix insn_sanity build failure after UAPI split
UAPI: x86: Fix the test_get_len tool
UAPI: (Scripted) Set up UAPI Kbuild files
UAPI: Partition the header include path sets and add uapi/ header directories
UAPI: (Scripted) Convert #include "..." to #include <path/...> in kernel system headers
UAPI: (Scripted) Convert #include "..." to #include <path/...> in drivers/gpu/
UAPI: (Scripted) Remove redundant DRM UAPI header #inclusions from drivers/gpu/.
UAPI: Refer to the DRM UAPI headers with <...> and from certain headers only
handling. We used to reserve 2% of the partition, but now we are
more aggressive and we reserve 2% of the entire chip, which is
what actually manufacturers specify in data sheets. We introduced
an option to users to override the default, though.
There are a couple of fixes as well, and a number of cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=95SE
-----END PGP SIGNATURE-----
Merge tag 'upstream-3.7-rc1' of git://git.infradead.org/linux-ubi
Pull UBI changes from Artem Bityutskiy:
"The main change is the way we reserve eraseblocks for bad blocks
handling. We used to reserve 2% of the partition, but now we are more
aggressive and we reserve 2% of the entire chip, which is what
actually manufacturers specify in data sheets. We introduced an
option to users to override the default, though.
There are a couple of fixes as well, and a number of cleanups."
* tag 'upstream-3.7-rc1' of git://git.infradead.org/linux-ubi: (24 commits)
UBI: fix trivial typo 'it' => 'is'
UBI: load after mtd device drivers
UBI: print less
UBI: use pr_ helper instead of printk
UBI: comply with coding style
UBI: erase free PEB with bitflip in EC header
UBI: fix autoresize handling in R/O mode
UBI: add max_beb_per1024 to attach ioctl
UBI: allow specifying bad PEBs limit using module parameter
UBI: check max_beb_per1024 value in ubi_attach_mtd_dev
UBI: prepare for max_beb_per1024 module parameter addition
UBI: introduce MTD_PARAM_MAX_COUNT
UBI: separate bad_peb_limit in a function
arm: sam9_l9260_defconfig: correct CONFIG_MTD_UBI_BEB_LIMIT
UBI: use the whole MTD device size to get bad_peb_limit
mtd: mtdparts: introduce mtd_get_device_size
mtd: mark mtd_is_partition argument as constant
arm: sam9_l9260_defconfig: remove non-existing config option
UBI: kill CONFIG_MTD_UBI_BEB_RESERVE
UBI: limit amount of reserved eraseblocks for bad PEB handling
...
Pull CMA and DMA-mapping updates from Marek Szyprowski:
"This time the pull request is rather small, because the further
redesign patches were not ready on time.
This pull request consists of the patches which extend ARM DMA-mapping
subsystem with support for CPU coherent (ACP) DMA busses. The first
client of the new version is HighBank SATA driver. The second part of
the pull request includes various cleanup for both CMA common code and
ARM DMA-mapping subsystem."
Fix up trivial add-add conflict due to the "dma-coherent" DT property
being added next to the "calxeda,port-phys" property for the Calxeda
AHCI controller.
* 'for-v3.7' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
ARM: dma-mapping: Remove unsed var at arm_coherent_iommu_unmap_page
ARM: highbank: add coherent DMA setup
ARM: kill off arch_is_coherent
ARM: add coherent iommu dma ops
ARM: add coherent dma ops
ARM: dma-mapping: Refrain noisy console message
ARM: dma-mapping: Small logical clean up
drivers: dma-contiguous: refactor dma_alloc_from_contiguous()
* Improved system suspend/resume and runtime PM handling for the SH TMU, CMT
and MTU2 clock event devices (also used by ARM/shmobile).
* Generic PM domains framework extensions related to cpuidle support and
domain objects lookup using names.
* ARM/shmobile power management updates including improved support for the
SH7372's A4S power domain containing the CPU core.
* cpufreq changes related to AMD CPUs support from Matthew Garrett, Andre
Przywara and Borislav Petkov.
* cpu0 cpufreq driver from Shawn Guo.
* cpufreq governor fixes related to the relaxing of limit from Michal Pecio.
* OMAP cpufreq updates from Axel Lin and Richard Zhao.
* cpuidle ladder governor fixes related to the disabling of states from
Carsten Emde and me.
* Runtime PM core updates related to the interactions with the system suspend
core from Alan Stern and Kevin Hilman.
* Wakeup sources modification allowing more helper functions to be called from
interrupt context from John Stultz and additional diagnostic code from Todd
Poynor.
* System suspend error code path fix from Feng Hong.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=rbCk
-----END PGP SIGNATURE-----
Merge tag 'pm-for-3.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael J Wysocki:
- Improved system suspend/resume and runtime PM handling for the SH
TMU, CMT and MTU2 clock event devices (also used by ARM/shmobile).
- Generic PM domains framework extensions related to cpuidle support
and domain objects lookup using names.
- ARM/shmobile power management updates including improved support for
the SH7372's A4S power domain containing the CPU core.
- cpufreq changes related to AMD CPUs support from Matthew Garrett,
Andre Przywara and Borislav Petkov.
- cpu0 cpufreq driver from Shawn Guo.
- cpufreq governor fixes related to the relaxing of limit from Michal
Pecio.
- OMAP cpufreq updates from Axel Lin and Richard Zhao.
- cpuidle ladder governor fixes related to the disabling of states from
Carsten Emde and me.
- Runtime PM core updates related to the interactions with the system
suspend core from Alan Stern and Kevin Hilman.
- Wakeup sources modification allowing more helper functions to be
called from interrupt context from John Stultz and additional
diagnostic code from Todd Poynor.
- System suspend error code path fix from Feng Hong.
Fixed up conflicts in cpufreq/powernow-k8 that stemmed from the
workqueue fixes conflicting fairly badly with the removal of support for
hardware P-state chips. The changes were independent but somewhat
intertwined.
* tag 'pm-for-3.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (76 commits)
Revert "PM QoS: Use spinlock in the per-device PM QoS constraints code"
PM / Runtime: let rpm_resume() succeed if RPM_ACTIVE, even when disabled, v2
cpuidle: rename function name "__cpuidle_register_driver", v2
cpufreq: OMAP: Check IS_ERR() instead of NULL for omap_device_get_by_hwmod_name
cpuidle: remove some empty lines
PM: Prevent runtime suspend during system resume
PM QoS: Use spinlock in the per-device PM QoS constraints code
PM / Sleep: use resume event when call dpm_resume_early
cpuidle / ACPI : move cpuidle_device field out of the acpi_processor_power structure
ACPI / processor: remove pointless variable initialization
ACPI / processor: remove unused function parameter
cpufreq: OMAP: remove loops_per_jiffy recalculate for smp
sections: fix section conflicts in drivers/cpufreq
cpufreq: conservative: update frequency when limits are relaxed
cpufreq / ondemand: update frequency when limits are relaxed
properly __init-annotate pm_sysrq_init()
cpufreq: Add a generic cpufreq-cpu0 driver
PM / OPP: Initialize OPP table from device tree
ARM: add cpufreq transiton notifier to adjust loops_per_jiffy for smp
cpufreq: Remove support for hardware P-state chips from powernow-k8
...
1) Apply -- and then revert -- the FUA feature. Caused
disk corruption in linux-next, proving it cannot be turned on by
default.
Net effect to upstream tree: zero
2) New AHCI platform driver sata_highbank
3) Improve SCSI MODE SENSE handling; support MODE SELECT
4) AHCI: support aggressive device sleep (power mgmt)
5) sata_fsl: minor fix
6) pata_arasan: clk support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIVAwUAUGtCHCWzCDIBeCsvAQLHFA//X6IM8ymHasCzEXvB2IusarPZYqfrGOUX
DVHPPeBdNbuNtX1iIp9NEvx5PONEvBgylrzbH0jOW9f+8GZM7sgT0NFlUWAfg7hO
HF3RN3EsQMMcSK+BoOLzo+vzSEAIbPB7zqKAGqh9QBBpfKAYbAy2WHr7P5OMuy9J
IjKoknc8jaOWavg8oavx3dU5PCFU7BoPQzrPSNB/MY5L1Ia3H29zyCmoW1Ha05wa
LRZzJes4X3H+tStNhtrNmItaRfxJNW7xPluNOn4FIyQmK+Nh3NDk6IBuwPdFpltn
m6azzOfHreaP9J9xcIiU1NX7Gu+IBYZpOyL61B+WUmCRLXMdnhDTZE6mkKe10ReZ
o9oBn636swDVMXG+zS0hjv+nQgV0l+sHX/0GsTCxDapZal7icCUsLzW9flaCh0n+
zkwoxjvGZOkFf6ZsAgFVo8h2YMe7Ph2I5JIiN12rqee4grV7cHStKQn076Kyb9zo
5LsR1/+YuuWz9G2dEmirDA8xBtydIZ4thvblwXipnqyZWkAwLue+opIWxau7BlPZ
qz6KjNp2L1hS8QgQnYHYmk/EDPDg5SNP4RTCCO9TKUBcu9fcke2c+R8V7ebKCI02
AaaccV4N6t7c1rdQUH6bnizi9aZ+tRoBAheLEDrrkOx72f71hE6JgueqhI+EaTw6
LyrSiiVITxA=
=i3EH
-----END PGP SIGNATURE-----
Merge tag 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
Pull libata changes from Jeff Garzik:
"Minor libata updates, nothing notable.
1) Apply -- and then revert -- the FUA feature. Caused disk
corruption in linux-next, proving it cannot be turned on by
default.
Net effect to upstream tree: zero
2) New AHCI platform driver sata_highbank
3) Improve SCSI MODE SENSE handling; support MODE SELECT
4) AHCI: support aggressive device sleep (power mgmt)
5) sata_fsl: minor fix
6) pata_arasan: clk support"
* tag 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
sata_mv: Fix warnings when no PCI
[libata] Makefile: Fix build error in sata_highbank
[libata] export ata_dev_set_feature()
libata-core: use ATA_LBA in ata_build_rw_tf()
ata/ahci_platform: Add clock framework support
pata_arasan: add Device Tree probing capability
pata_arasan: Add clk_{un}prepare() support
ata: add platform driver for Calxeda AHCI controller
sata_fsl: add workaround for data length mismatch on freescale V2 controller
ahci: implement aggressive SATA device sleep support
ata: define enum constants for IDENTIFY DEVICE
Revert "libata: enable SATA disk fua detection on default"
[libata] scsi: implement MODE SELECT command
[libata] scsi: support MODE SENSE request for changeable and default parameters
[libata] scsi: Remove unlikely() from FUA check
libata: enable SATA disk fua detection on default
No framework work here, only a bunch of driver updates of varying sizes:
- Factoring out of the core hardware support from the MXS MMC driver by
Marek Vasut to allow the hardware to also be used for SPI.
- Lots of error handling cleanups from Guenter Roeck
- Removal of the existing Tegra driver which is quite comprehensively
broken as detailed in the changelog for the removal.
- DT suppport for the PL022 and GPIO drivers.
- pinctrl support for OMAP and PL022.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=ld23
-----END PGP SIGNATURE-----
Merge tag 'spi-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc
Pull spi updates from Mark Brown:
"No framework work here, only a bunch of driver updates of varying
sizes:
- Factoring out of the core hardware support from the MXS MMC driver
by Marek Vasut to allow the hardware to also be used for SPI.
- Lots of error handling cleanups from Guenter Roeck
- Removal of the existing Tegra driver which is quite comprehensively
broken as detailed in the changelog for the removal.
- DT suppport for the PL022 and GPIO drivers.
- pinctrl support for OMAP and PL022."
Pulling from Mark Brown as Grant Likely is still busy moving.
* tag 'spi-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc: (53 commits)
spi: remove completely broken Tegra driver
spi/imx: set the inactive state of the clock according to the clock polarity
spi/pl022: get/put resources on suspend/resume
spi/pl022: use more managed resources
spi/pl022: Devicetree support w/o platform data
spi/s3c64xx: Don't free controller_data on non-dt platforms
spi: omap2-mcspi: add pinctrl support
spi/pl022: adopt pinctrl support
spi: omap2-mcspi: Cleanup the omap2_mcspi_txrx_dma function
spi/gpio: Fix stub for spi_gpio_probe_dt()
spi/mxs: Make the SPI block clock speed configurable via DT
spi: spi-sh-hspi: drop frees of devm_ alloc'd data
spi/pl022: Fix chipselects pointer computation
spi: spi-tle62x0: Use module_spi_driver macro
mxs/spi: Rework the mxs_ssp_timeout to be more readable
mxs/spi: Decrement the DMA/PIO border
mxs/spi: Increment the transfer length only if transfer succeeded
mxs/spi: Fix issues when doing long continuous transfer
spi: spi-gpio: Add DT bindings
spi: spi-gpio: store chipselect information in private structure
...
Pull input updates from Dmitry Torokhov:
"A few drivers were updated with device tree bindings and others got a
few small cleanups and fixes."
Fix trivial conflict in drivers/input/keyboard/omap-keypad.c due to
changes clashing with a whitespace cleanup.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (28 commits)
Input: wacom - mark Intuos5 pad as in-prox when touching buttons
Input: synaptics - adjust threshold for treating position values as negative
Input: hgpk - use %*ph to dump small buffer
Input: gpio_keys_polled - fix dt pdata->nbuttons
Input: Add KD[GS]KBDIACRUC ioctls to the compatible list
Input: omap-keypad - fixed formatting
Input: tegra - move platform data header
Input: wacom - add support for EMR on Cintiq 24HD touch
Input: s3c2410_ts - make s3c_ts_pmops const
Input: samsung-keypad - use of_get_child_count() helper
Input: samsung-keypad - use of_match_ptr()
Input: uinput - fix formatting
Input: uinput - specify exact bit sizes on userspace APIs
Input: uinput - mark failed submission requests as free
Input: uinput - fix race that can block nonblocking read
Input: uinput - return -EINVAL when read buffer size is too small
Input: uinput - take event lock when fetching events from buffer
Input: get rid of MATCH_BIT() macro
Input: rotary-encoder - add DT bindings
Input: rotary-encoder - constify platform data pointers
...
- Add subdrivers for the DB8540 and NHK8815 Nomadik-type ASICs,
provide platform config for the Nomadik.
- Add a driver for the i.MX35.
- Add a driver for the BCM2835, an advanced GPIO expander.
- Various fixes and clean-ups and minor improvements for the core,
Nomadik, pinctr-single, sirf drivers.
- Some platform config for the ux500.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=g2i2
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl changes from Linus Walleij:
"Some of this stuff is hitting arch/arm/* and have been ACKed by the
ARM SoC folks, or it's device tree bindings pertaining to the specific
driver.
These are the bulk pinctrl changes for kernel v3.7:
- Add subdrivers for the DB8540 and NHK8815 Nomadik-type ASICs,
provide platform config for the Nomadik.
- Add a driver for the i.MX35.
- Add a driver for the BCM2835, an advanced GPIO expander.
- Various fixes and clean-ups and minor improvements for the core,
Nomadik, pinctr-single, sirf drivers.
- Some platform config for the ux500."
* tag 'pinctrl-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (27 commits)
pinctrl: add bcm2835 driver
pinctrl: clarify idle vs sleep states
pinctrl/nomadik: use irq_find_mapping()
pinctrl: sirf: add lost chained_irq_enter and exit in sirfsoc_gpio_handle_irq
pinctrl: sirf: initialize the irq_chip pointer of pinctrl_gpio_range
pinctrl: sirf: fix spinlock deadlock in sirfsoc_gpio_set_input
pinctrl: sirf: add missing pins to pinctrl list
pinctrl: sirf: fix a typo in sirfsoc_gpio_probe
pinctrl: pinctrl-single: add debugfs pin h/w state info
ARM: ux500: 8500: update I2C sleep states pinctrl
pinctrl: Fix potential memory leak in pinctrl_register_one_pin()
ARM: ux500: tidy up pin sleep modes
ARM: ux500: fix spi2 pin group
pinctrl: imx: remove duplicated const
pinctrl: document semantics vs GPIO
ARM: ux500: 8500: use hsit_a_2 group for HSI
pinctrl: use kasprintf() in pinmux_request_gpio()
pinctrl: pinctrl-single: Add pinctrl-single,bits type of mux
pinctrl/nomadik : add MC1_a_2 pin MC1 function group list
pinctrl: pinctrl-single: Make sure we do not change bits outside of mask
...
- refactoring from Thierry Redding at Arnd Bergmann's request to use
the seq_file iterator interface in gpiolib.
- A new driver for Avionic Design's N-bit GPIO expander.
- Two instances of mutexes replaced by spinlocks from Axel Lin to
code that is supposed to be fastpath compliant.
- IRQ demuxer and gpio_to_irq() support for pcf857x by Kuninori
Morimoto.
- Dynamic GPIO numbers, device tree support, daisy chaining and some
other fixes for the 74x164 driver by Maxime Ripard.
- IRQ domain and device tree support for the tc3589x driver by
Lee Jones.
- Some conversion to use managed resources devm_* code.
- Some instances of clk_prepare() or clk_prepare_enable() added to
support the new, stricter common clock framework.
- Some for_each_set_bit() simplifications.
- Then a lot of fixes as we fixed up all of the above tripping over
our own shoelaces and that kind of thing.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=jbUM
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO changes from Linus Walleij:
"So this is the LW GPIO patch stack for v3.7:
- refactoring from Thierry Redding at Arnd Bergmann's request to use
the seq_file iterator interface in gpiolib.
- A new driver for Avionic Design's N-bit GPIO expander.
- Two instances of mutexes replaced by spinlocks from Axel Lin to
code that is supposed to be fastpath compliant.
- IRQ demuxer and gpio_to_irq() support for pcf857x by Kuninori
Morimoto.
- Dynamic GPIO numbers, device tree support, daisy chaining and some
other fixes for the 74x164 driver by Maxime Ripard.
- IRQ domain and device tree support for the tc3589x driver by Lee
Jones.
- Some conversion to use managed resources devm_* code.
- Some instances of clk_prepare() or clk_prepare_enable() added to
support the new, stricter common clock framework.
- Some for_each_set_bit() simplifications.
- Then a lot of fixes as we fixed up all of the above tripping over
our own shoelaces and that kind of thing."
* tag 'gpio-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (34 commits)
gpio: pcf857x: select IRQ_DOMAIN
gpio: Document device_node's det_debounce
gpio-lpc32xx: Add GPI_28
gpio: adnp: dt: Reference generic interrupt binding
gpio: Add Avionic Design N-bit GPIO expander support
gpio: pxa: using for_each_set_bit to simplify the code
gpio_msm: using for_each_set_bit to simplify the code
gpio: Enable the tc3298x GPIO expander driver for Device Tree
gpio: Provide the tc3589x GPIO expander driver with an IRQ domain
ARM: shmobile: kzm9g: use gpio-keys instead of gpio-keys-polled
gpio: pcf857x: fixup smatch WARNING
gpio: 74x164: Add support for the daisy-chaining
gpio: 74x164: dts: Add documentation for the dt binding
dt: Fix incorrect reference in gpio-led documentation
gpio: 74x164: Add device tree support
gpio: 74x164: Use dynamic gpio number assignment if no pdata is present
gpio: 74x164: Use devm_kzalloc
gpio: 74x164: Use module_spi_driver boiler plate function
gpio: sx150x: Use irq_data_get_irq_chip_data() at appropriate places
gpio: em: Use irq_data_get_irq_chip_data() at appropriate places
...
Select POWER_SUPPLY from POWER_AVS_OMAP entry in Kconfig.
This avoids the following build problems using a randconfig
that has CONFIG_POWER_SUPPLY not set:
LD init/built-in.o
arch/arm/mach-omap2/built-in.o: In function `sr_class3_configure':
arch/arm/mach-omap2/smartreflex-class3.c:44: undefined reference to `sr_configure_errgen'
arch/arm/mach-omap2/built-in.o: In function `sr_class3_disable':
arch/arm/mach-omap2/smartreflex-class3.c:33: undefined reference to `sr_disable_errgen'
arch/arm/mach-omap2/smartreflex-class3.c:35: undefined reference to `sr_disable'
arch/arm/mach-omap2/built-in.o: In function `sr_class3_enable':
arch/arm/mach-omap2/smartreflex-class3.c:28: undefined reference to `sr_enable'
arch/arm/mach-omap2/built-in.o: In function `sr_class3_init':
arch/arm/mach-omap2/smartreflex-class3.c:59: undefined reference to `sr_register_class'
make: *** [vmlinux] Error 1
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
In case of error, the function voltdm_lookup() returns NULL
not ERR_PTR(). The IS_ERR() test in the return value check
should be replaced with NULL test.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
In case of error, the function voltdm_lookup() returns NULL
not ERR_PTR(). The IS_ERR() test in the return value check
should be replaced with NULL test.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
In case of error, the function omap_device_alloc() returns ERR_PTR()
and never returns NULL pointer. The NULL test in the return value
check should be replaced with IS_ERR().
dpatch engine is used to auto generated this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Kevin Hilman <khilman@ti.com>
In case of error, the function omap_device_get_by_hwmod_name()
returns ERR_PTR() not NULL pointer. The NULL test in the return
value check should be replaced with IS_ERR().
dpatch engine is used to auto generated this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Set up empty UAPI Kbuild files to be populated by the header splitter.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
Convert #include "..." to #include <path/...> in kernel system headers.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
Arnd Bergmann