Pull ARM updates from Russell King:
"This is the first chunk of ARM updates for this merge window.
Conflicts are expected in two files - asm/timex.h and
mach-integrator/integrator_cp.c. Nothing particularly stands out more
than anything else.
Most of the growth is down to the opcodes stuff from Dave Martin,
which is countered by Rob's patches to use more of the asm-generic
headers on ARM."
(A few more conflicts grew since then, but it all looked fairly trivial)
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm: (44 commits)
ARM: 7548/1: include linux/sched.h in syscall.h
ARM: 7541/1: Add ARM ERRATA 775420 workaround
ARM: ensure vm_struct has its phys_addr member filled in
ARM: 7540/1: kexec: Check segment memory addresses
ARM: 7539/1: kexec: scan for dtb magic in segments
ARM: 7538/1: delay: add registration mechanism for delay timer sources
ARM: 7536/1: smp: Formalize an IPI for wakeup
ARM: 7525/1: ptrace: use updated syscall number for syscall auditing
ARM: 7524/1: support syscall tracing
ARM: 7519/1: integrator: convert platform devices to Device Tree
ARM: 7518/1: integrator: convert AMBA devices to device tree
ARM: 7517/1: integrator: initial device tree support
ARM: 7516/1: plat-versatile: add DT support to FPGA IRQ
ARM: 7515/1: integrator: check PL010 base address from resource
ARM: 7514/1: integrator: call common init function from machine
ARM: 7522/1: arch_timers: register a time/cycle counter
ARM: 7523/1: arch_timers: enable the use of the virtual timer
ARM: 7531/1: mark kernelmode mem{cpy,set} non-experimental
ARM: 7520/1: Build dtb files in all target
ARM: Fix build warning in arch/arm/mm/alignment.c
...
This is a pretty significant branch. It's the introduction of the
first multiplatform support on ARM, and with this (and the later
branch) merged, it is now possible to build one kernel that contains
support for highbank, vexpress, mvebu, socfpga, and picoxcell. More
platforms will be convered over in the next few releases.
Two critical last things had to be done for this to be practical and
possible:
* Today each platform has its own include directory under
mach-<mach>/include/mach/*, and traditionally that is where a lot of
driver/platform shared definitions have gone, such as platform data
structures. They now need to move out to a common location instead,
and this branch moves a large number of those out to
include/linux/platform_data.
* Each platform used to list the device trees to compile for its
boards in mach-<mach>/Makefile.boot.
Both of the above changes will mean that there are some merge
conflicts to come (and some to resolve here). It's a one-time move and
once it settles in, we should be good for quite a while. Sorry for the
overhead.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJQaO7aAAoJEIwa5zzehBx3bUIP/02U8PhkHJJrrowyIsWRBOql
7LPJ53PRRgrpBdmEGzFD3TO3zaNyrjQRbYgNDvzHMO6NAMNvdRFouuWYjO11/tuB
i32zssXCC+eUOEgbAo/U/lYq+UOvqw9gv6mU+3+i3OcGEhdKOaoT/DSLPQC4hoDm
222TeLfFB3HJXu5n720dEQ9V3fO6TS1+bbh8TU3cjHqzceXsOrffZqOA5CQxUcRr
KWwOjA0nALDwWcqgv45GJNwY3GTyAQ/hPMQavnuWK0voJ+qUYk5HftKocAK7C+py
0T0OFOAHTwtyhvzJBxLC84M6Ox465BYXyeNjIB+2nG/Um9+mDoP0dnWpGy4c7DMU
P5hyqbeLGeqjUXQuYtRmgMMc3UeHKoUGAfXW9eMsjLa6/M4NLGv//7E7LbZPpgMZ
obkjwuesmcaYn/FRyj/yFmC35YlF4oCLziVzEtURZw3eKHHSUlhkTDSMNnkcZ0kZ
Vv7kFxnD2Y46ixiwSJv30ErQnVkgI3MdqDlDxkE8r5+phYuK4gCrNaJtiwRh/oNw
cFhpPxKuA0sJ9b6YRTzjC45eT/XZomEEr/uifCFeRNaCquyjYP00Mm8F0flSqwx9
zi+emzPAwNmk1bvxMUM/idGnaj0V4p+BAYUAvkbSoqU1p1flzyhU88fGTSIyKOt6
K5TCDS2v5hrVykK9TDwl
=Tc6y
-----END PGP SIGNATURE-----
Merge tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc multiplatform enablement from Olof Johansson:
"This is a pretty significant branch. It's the introduction of the
first multiplatform support on ARM, and with this (and the later
branch) merged, it is now possible to build one kernel that contains
support for highbank, vexpress, mvebu, socfpga, and picoxcell. More
platforms will be convered over in the next few releases.
Two critical last things had to be done for this to be practical and
possible:
* Today each platform has its own include directory under
mach-<mach>/include/mach/*, and traditionally that is where a lot
of driver/platform shared definitions have gone, such as platform
data structures. They now need to move out to a common location
instead, and this branch moves a large number of those out to
include/linux/platform_data.
* Each platform used to list the device trees to compile for its
boards in mach-<mach>/Makefile.boot.
Both of the above changes will mean that there are some merge
conflicts to come (and some to resolve here). It's a one-time move
and once it settles in, we should be good for quite a while. Sorry
for the overhead."
Fix conflicts as per Olof.
* tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (51 commits)
ARM: add v7 multi-platform defconfig
ARM: msm: Move core.h contents into common.h
ARM: highbank: call highbank_pm_init from .init_machine
ARM: dtb: move all dtb targets to common Makefile
ARM: spear: move platform_data definitions
ARM: samsung: move platform_data definitions
ARM: orion: move platform_data definitions
ARM: vexpress: convert to multi-platform
ARM: initial multiplatform support
ARM: mvebu: move armada-370-xp.h in mach dir
ARM: vexpress: remove dependency on mach/* headers
ARM: picoxcell: remove dependency on mach/* headers
ARM: move all dtb targets out of Makefile.boot
ARM: picoxcell: move debug macros to include/debug
ARM: socfpga: move debug macros to include/debug
ARM: mvebu: move debug macros to include/debug
ARM: vexpress: move debug macros to include/debug
ARM: highbank: move debug macros to include/debug
ARM: move debug macros to common location
ARM: make mach/gpio.h headers optional
...
socfpga, picoxcell, and vexpress.
Multi-platform support is dependent on mach/gpio.h removal and
restructuring of DEBUG_LL and dtb build rules included in this branch.
This has been built for all defconfigs, and booted on highbank with
all 5 platforms enabled.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQU4miAAoJEMhvYp4jgsXi1vMH/A4JJXe24cyo31rHJspZDSFg
nnCbnGKfDEOIHwLA8C3OeJuhswMlP/vWlGC512QXL8903XpZ2VJe63f2CLo1mN7Z
hg3JPWrp2VXZ/bqdMnUcw2CtlylrhyG9MUPapkcp+5Agjz2lwaJtRNL6LRRQX4Ei
cWjsJtaFpRj1QraFna0hpTQNO640je6s1rAIJl6eNOuX08l12ZAGDUA+IUUsa1cA
0OGeOAjH6gmkpMI89j1VPPKVRLHIdP4QcxmAZCHJ2LtvylyrlmYskctpAYibobvt
JPLnZgzMFAegnWtJhOYodhBJlfyypEeh2fsZVyDPowqRz9vaAWRjs6u/I4GYaME=
=HR3H
-----END PGP SIGNATURE-----
Merge tag 'multi-platform-for-3.7' of git://sources.calxeda.com/kernel/linux into next/multiplatform
Enable initial ARM multi-platform support for highbank, mvebu,
socfpga, picoxcell, and vexpress.
Multi-platform support is dependent on mach/gpio.h removal and
restructuring of DEBUG_LL and dtb build rules included in this branch.
This has been built for all defconfigs, and booted on highbank with
all 5 platforms enabled.
By Rob Herring (18) and Arnd Bergmann (1)
via Rob Herring
* tag 'multi-platform-for-3.7' of git://sources.calxeda.com/kernel/linux:
ARM: vexpress: convert to multi-platform
ARM: initial multiplatform support
ARM: mvebu: move armada-370-xp.h in mach dir
ARM: vexpress: remove dependency on mach/* headers
ARM: picoxcell: remove dependency on mach/* headers
ARM: move all dtb targets out of Makefile.boot
ARM: picoxcell: move debug macros to include/debug
ARM: socfpga: move debug macros to include/debug
ARM: mvebu: move debug macros to include/debug
ARM: vexpress: move debug macros to include/debug
ARM: highbank: move debug macros to include/debug
ARM: move debug macros to common location
ARM: make mach/gpio.h headers optional
ARM: orion: move custom gpio functions to orion-gpio.h
ARM: shmobile: move custom gpio functions to sh-gpio.h
ARM: pxa: use gpio_to_irq for sharppm_sl
net: pxaficp_ir: add irq resources
usb: pxa27x_udc: remove IRQ_USB define
staging: ste_rmi4: remove gpio.h include
Conflicts due to addition of bcm2835 and removal of pnx4008 in:
arch/arm/Kconfig
arch/arm/Makefile
Conflicts due to new dtb targets, moved to arch/arm/boot/dts/Makefile in:
arch/arm/mach-imx/Makefile.boot
arch/arm/mach-mxs/Makefile.boot
arch/arm/mach-tegra/Makefile.boot
Signed-off-by: Olof Johansson <olof@lixom.net>
The zImage loader needs to turn on the MMU in order to take
advantage of caching while decompressing the zImage. Running this
in hyp mode would require the LPAE pagetable format to be
supported; to avoid this complexity, this patch switches out of hyp
mode, and returns back to hyp mode just before booting the kernel.
This implementation assumes that the Hyp mode view of memory and the
PL1 view of memory are coherent, providing that the MMU and caches
are off in both, as required by the boot protocol. The zImage
decompression code must drain the write buffer on completion anyway, and
entry into Hyp mode should flush any prefetch buffer, avoiding hazards
associated with local write buffers and the pipeline.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This patch zeroes the SCTLR.TRE bit prior to setting the mapping as
cacheable for ARMv7 cores in the decompressor, ensuring that the
memory region attributes are obtained from the C and B bits, not from
the page tables.
Cc: Nicolas Pitre <nico@fluxnic.net>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Matthew Leach <matthew.leach@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This lets us build a multiplatform kernel for experimental purposes.
However, it will not be useful for any real work, because it relies
on a number of useful things to be disabled for now:
* SMP support must be turned off because of conflicting symbols.
Marc Zyngier has proposed a solution by adding a new SOC
operations structure to hold indirect function pointers
for these, but that work is currently stalled
* We turn on SPARSE_IRQ unconditionally, which is not supported
on most platforms. Each of them is currently in a different
state, but most are being worked on.
* A common clock framework is in place since v3.4 but not yet
being used. Work on this is on its way.
* DEBUG_LL for early debugging is currently disabled.
* THUMB2_KERNEL does not work with allyesconfig because the
kernel gets too big
[Rob Herring]: Rebased to not be dependent on the mass mach header rename.
As a result, omap2plus, imx, mxs and ux500 are not converted. Highbank,
picoxcell, mvebu, and socfpga are converted.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
With the generic unaligned.h, more kernel headers get pulled in including
dynamic_debug.h which needs strstr. As it is not really used, we only need
a declaration here.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When enabling the MMU for ARMv7 CPUs, the decompressor does not touch
the ttbcr register, assuming that it will be zeroed (N == 0, EAE == 0).
Given that only EAE is defined as 0 for non-secure copies of the
register (and a bootloader such as kexec may leave it set to 1 anyway),
we should ensure that we reset the register ourselves before turning on
the MMU.
This patch zeroes TTBCR.EAE and TTBCR.N prior to enabling the MMU for
ARMv7 cores in the decompressor, configuring us exclusively for 32-bit
translation tables via TTBR0.
Cc: <stable@vger.kernel.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Matthew Leach <matthew.leach@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch allows the ATAG_CMDLINE provided by the bootloader to be
concatenated to the bootargs property of the device tree.
This is useful to merge static values defined in the device tree
with the boot loader's (possibly) more dynamic values, such as
startup reasons and more.
The bootloader should use the device tree to pass those values to
the kernel, but that's not always simple (old bootloader or very
small one).
The behaviour is the same as the one introduced by Victor Boivie in
4394c12442 by extending the CONFIG_CMDLINE.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
These cleanups are basically all over the place. The idea is to collect
changes with minimal impact but large number of changes so we can avoid
them from distracting in the diffstat in the other series.
A significant number of lines get removed here, in particular because
the ixp2000 and ixp23xx platforms get removed. These have never been
extremely popular and have fallen into disuse over time with no active
maintainer taking care of them. The u5500 soc never made it into a
product, so we are removing it from the ux500 platform.
Many good cleanups also went into the at91 and omap platforms, as has
been the case for a number of releases.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Hcjs
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull first batch of arm-soc cleanups from Olof Johansson:
"These cleanups are basically all over the place. The idea is to
collect changes with minimal impact but large number of changes so we
can avoid them from distracting in the diffstat in the other series.
A significant number of lines get removed here, in particular because
the ixp2000 and ixp23xx platforms get removed. These have never been
extremely popular and have fallen into disuse over time with no active
maintainer taking care of them. The u5500 soc never made it into a
product, so we are removing it from the ux500 platform.
Many good cleanups also went into the at91 and omap platforms, as has
been the case for a number of releases."
Trivial modify-delete conflicts in arch/arm/mach-{ixp2000,ixp23xx}
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (152 commits)
ARM: clps711x: Cleanup IRQ handling
ARM clps711x: Removed unused header mach/time.h
ARM: clps711x: Added note about support EP731x CPU to Kconfig
ARM: clps711x: Added missing register definitions
ARM: clps711x: Used own subarch directory for store header file
Dove: Fix Section mismatch warnings
ARM: orion5x: ts78xx debugging changes
ARM: orion5x: remove PM dependency from ts78xx
ARM: orion5x: ts78xx fix NAND resource off by one
ARM: orion5x: ts78xx whitespace cleanups
Orion5x: Fix Section mismatch warnings
Orion5x: Fix warning: struct pci_dev declared inside paramter list
ARM: clps711x: Combine header files into one for clps711x-targets
ARM: S3C24XX: Use common macro to define resources on mach-qt2410.c
ARM: S3C24XX: Use common macro to define resources on mach-osiris.c
ARM: EXYNOS: Adapt to cpuidle core time keeping and irq enable
ARM: S5PV210: Use common macro to define resources on mach-smdkv210.c
ARM: S5PV210: Use common macro to define resources on dev-audio.c
ARM: S5PC100: Use common macro to define resources on dev-audio.c
ARM: S5P64X0: Use common macro to define resources on dev-audio.c
...
We setup identity MMU mappings across the entire 4GB of space, which
are permissionless because the domain is set to manager.
This unfortunately allows ARMv6 and later CPUs to speculatively
prefetch from the entire address space, which can cause undesirable
side effects if those regions contain devices.
As we setup the mappings with read/write permission, we can switch
the domain to client mode, and then use the XN bit for ARMv6 and
above to control speculative prefetch to non-RAM areas.
Reported-by: R Sricharan <r.sricharan@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- The biggest improvement of this series is the ability to compile several
AT91 SoCs in one kernel image.
For now on it's limited to the DT-enabled boards but we can compile all
the core together.
- The Kconfig series is stacked before other patches as it is simple and
non-intrusive. Its goal is to remove too restrictive dependencies on
SoC names. This will allow to add support for newer SoC seamlessly.
- Some very "cosmetic" Kconfig changes are also added (entry names,
comments, etc.).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJPjYz4AAoJEAf03oE53VmQ/0wH/3kXJYM/8nX8fqlQ8eTh0SHi
lRsoNL+4arHFKcocYhZyiXEidUKCUMLuQSdvL9MWy1e286+ABsaFgrjfLsp/ZDqE
jDJBCZIxUD6rL94VRnYEHrhWqGzzPKi8/syVZ8JOv/1HGml402CqPcRDKmWY/e4Q
ajl/d463q0ufwfQ4LMP+DsR29TxEdecs4DkxnhwcrRCbJ2hDPLmWVER+tPITPwqp
R8qVGY3K6axG68b964B/hsACjRF7C1lqRQsiQbi8pVPPGEhekmgnW8hF6dNdy1VW
wVo8F0GCST6jLk9YFbirBdKsDRJTLc+WsyP6jUZyWkrrM6p4ycs+voGFDNZbhPw=
=CXyd
-----END PGP SIGNATURE-----
Merge tag 'at91-3.5-cleanup' of git://github.com/at91linux/linux-at91 into next/cleanup
Nicolas Ferre <nicolas.ferre@atmel.com> writes:
First batch of AT91 cleanup for 3.5 kernel.
- The biggest improvement of this series is the ability to compile several
AT91 SoCs in one kernel image.
For now on it's limited to the DT-enabled boards but we can compile all
the core together.
- The Kconfig series is stacked before other patches as it is simple and
non-intrusive. Its goal is to remove too restrictive dependencies on
SoC names. This will allow to add support for newer SoC seamlessly.
- Some very "cosmetic" Kconfig changes are also added (entry names,
comments, etc.).
* tag 'at91-3.5-cleanup' of git://github.com/at91linux/linux-at91: (19 commits)
ARM: at91: add defconfig for device tree
ARM: at91/dt: do not specify the board any more
ARN: at91: introduce SOC_AT91xxx define to allow to compile SoC core support
ARM: at91: add SOC_AT91SAM9 kconfig option to factorise select
ARM: at91: pm select memory controler at runtime
ARM: at91: move at91_init_leds to board init
ARM: at91: do not pin mux the UARTs in init_early
ARM: at91: drop at91_set_serial_console
ARM: at91: uncompress: autodetect the uart to use
ARM: at91: uncompress Store UART address in a variable
hwrng: Kconfig: remove dependency for atmel-rng driver
Input: Kconfig: remove dependency for atmel_tsadcc driver
rtc: Kconfig: remove dependency for AT91 rtc driver
ARM: at91/Kconfig: website link for AT91SAM9G20-EK
ARM: at91/Kconfig: add AT91SAM9x5 family to AT91_EARLY_DBGU0 entry
ARM: at91/Kconfig: add clarifications to AT91SAM9M10G45-EK entry
ARM: at91/Kconfig: add comment to at91sam9x5 family entry
ARM: at91/Kconfig: change at91sam9g45 entry
ARM: at91: change AT91 Kconfig entry comment
Also updates the cleanup branch to v3.4-rc3.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Some bootloaders are broken enough to expose an ATAG_MEM with
a null size. Converting such tag to a memory node leads to
an unbootable system.
Skip over zero sized ATAG_MEM to avoid this situation.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
atags_to_fdt() returns 1 when it fails to find a valid FDT signature.
The CONFIG_ARM_ATAG_DTB_COMPAT code is supposed to retry with another
location, but only does so when the initial call doesn't fail.
Fix this by using the correct condition in the assembly code.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ixp2xxx platforms have had no real changes since ~2006 and the maintainer
has said on irc that they can be removed:
13:05 < nico> do you still care about ixp2000?
13:22 < lennert> not really, no
13:58 < nico> do you think we could remove it from the kernel tree?
14:01 < lennert> go for it, and remove ixp23xx too while you're at it
Removing will help simplify ARM consolidation in general and PCI re-work
specifically.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Pull more ARM updates from Russell King.
This got a fair number of conflicts with the <asm/system.h> split, but
also with some other sparse-irq and header file include cleanups. They
all looked pretty trivial, though.
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm: (59 commits)
ARM: fix Kconfig warning for HAVE_BPF_JIT
ARM: 7361/1: provide XIP_VIRT_ADDR for no-MMU builds
ARM: 7349/1: integrator: convert to sparse irqs
ARM: 7259/3: net: JIT compiler for packet filters
ARM: 7334/1: add jump label support
ARM: 7333/2: jump label: detect %c support for ARM
ARM: 7338/1: add support for early console output via semihosting
ARM: use set_current_blocked() and block_sigmask()
ARM: exec: remove redundant set_fs(USER_DS)
ARM: 7332/1: extract out code patch function from kprobes
ARM: 7331/1: extract out insn generation code from ftrace
ARM: 7330/1: ftrace: use canonical Thumb-2 wide instruction format
ARM: 7351/1: ftrace: remove useless memory checks
ARM: 7316/1: kexec: EOI active and mask all interrupts in kexec crash path
ARM: Versatile Express: add NO_IOPORT
ARM: get rid of asm/irq.h in asm/prom.h
ARM: 7319/1: Print debug info for SIGBUS in user faults
ARM: 7318/1: gic: refactor irq_start assignment
ARM: 7317/1: irq: avoid NULL check in for_each_irq_desc loop
ARM: 7315/1: perf: add support for the Cortex-A7 PMU
...
This patch changes the ARCH name to "ARCH_S3C24XX" for Samsung
S3C2410, S3C2412, S3C2413, S3C2416, S3C2440, S3C2442, S3C2443,
and S3C2450 SoCs so that we can merge the mach-xxx directories
and plat-s3c24xx dir. to just one mach-s3c24xx for them.
I think this should be sent to upstream via samsung tree because
this touches many samsung stuff.
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
[for the gadget part:]
Acked-by: Felipe Balbi <balbi@ti.com>
[for the framebuffer (video) part:]
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
[For the watchdog-part:]
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Cc: Sangbeom Kim <sbkim73@samsung.com>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Before we enable the MMU, we must ensure that the TTBR registers contain
sane values. After the MMU has been enabled, we jump to the *virtual*
address of the following function, so we also need to ensure that the
SCTLR write has taken effect.
This patch adds ISB instructions around the SCTLR write to ensure the
visibility of the above.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
If TEXT_OFFSET is too large (e.g. like on MSM) the resulting immediate
argument gets wider than 8 bits.
Noticed by David Brown <davidb@codeaurora.org>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Get rid of this complaint from dash:
AS arch/arm/boot/compressed/lib1funcs.o
/bin/sh: 1: [: y: unexpected operator
LD arch/arm/boot/compressed/vmlinux
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Without CONFIG_AUTO_ZRELADDR being set the kernel needs a single
zreladdr for building zImages. Bail out if we detect multiple
zreladdrs without CONFIG_AUTO_ZRELADDR.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The rule to copy this file doesn't have to be forced. However
lib1funcs.[So] have to be listed amongst the targets.
This prevents zImage from being recreated needlessly.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Dave Martin <dave.martin@linaro.org>
Tested-by: Thomas Abraham <thomas.abraham@linaro.org>
Some old bootloaders can't be updated to a device tree capable one,
yet they provide ATAGs with memory configuration, the ramdisk address,
the kernel cmdline string, etc. To allow a device tree enabled
kernel to be used with such bootloaders, it is necessary to convert those
ATAGs into FDT properties and fold them into the DTB appended to zImage.
Currently the following ATAGs are converted:
ATAG_CMDLINE
ATAG_MEM
ATAG_INITRD2
If the corresponding information already exists in the appended DTB, it
is replaced, otherwise the required node is created to hold it.
The code looks for ATAGs at the location pointed by the value of r2 upon
entry into the zImage code. If no ATAGs are found there, an attempt at
finding ATAGs at the typical 0x100 offset from start of RAM is made.
Otherwise the DTB is left unchanged.
Thisstarted from an older patch from John Bonesio <bones@secretlab.ca>,
with contributions from David Brown <davidb@codeaurora.org>.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Dave Martin <dave.martin@linaro.org>
Tested-by: Thomas Abraham <thomas.abraham@linaro.org>
This is a small subset of string functions needed by commits to come.
Except for memcpy() which is unchanged from its original location, their
implementation is meant to be small, and -Os is enforced to prevent gcc
from doing pointless loop unrolling.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Dave Martin <dave.martin@linaro.org>
Tested-by: Thomas Abraham <thomas.abraham@linaro.org>
The appended DTB gets relocated with the decompressor code to get out
of the way of the decompressed kernel. However the kernel's .bss section
may be larger than the relocated code and data, and then the DTB gets
overwritten. Let's make sure the relocation takes care of moving zImage
far enough so no such conflict with .bss occurs.
Thanks to Tony Lindgren <tony@atomide.com> for figuring out this issue.
While at it, let's clean up the code a bit so that the wont_overwrite
symbol is used while determining if a conflict exists, making the above
change more precise as well as eliminating some ARM/THUMB alternates.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Dave Martin <dave.martin@linaro.org>
Tested-by: Thomas Abraham <thomas.abraham@linaro.org>
This patch provides the ability to boot using a device tree that is appended
to the raw binary zImage (e.g. cat zImage <filename>.dtb > zImage_w_dtb).
Signed-off-by: John Bonesio <bones@secretlab.ca>
[nico: ported to latest zImage changes plus additional cleanups/improvements]
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Dave Martin <dave.martin@linaro.org>
Tested-by: Thomas Abraham <thomas.abraham@linaro.org>
This is needed for proper alignment when the DTB appending feature
is used.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Dave Martin <dave.martin@linaro.org>
Tested-by: Thomas Abraham <thomas.abraham@linaro.org>
This corrects a logic-error that I made in the original implementation.
An alternate patch would be to just remove these lines and
leave the clock running as it is reconfigured later on during
boot anyway.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Currently, the documented kernel entry requirements are not
explicit about whether the kernel should be entered in ARM or
Thumb, leading to an ambiguitity about how to enter Thumb-2
kernels. As a result, the kernel is reliant on the zImage
decompressor to enter the kernel proper in the correct instruction
set state.
This patch changes the boot entry protocol for head.S and Image to
be the same as for zImage: in all cases, the kernel is now entered
in ARM.
Documentation/arm/Booting is updated to reflect this new policy.
A different rule will be needed for Cortex-M class CPUs as and when
support for those lands in mainline, since these CPUs don't support
the ARM instruction set at all: a note is added to the effect that
the kernel must be entered in Thumb on such systems.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Place read-only data in a .rodata output section, and the compressed
piggy data in .piggydata. Place the .got.plt section before the .got
section as is standard ELF practise.
This allows the piggydata to be more easily extracted from the
compressed vmlinux file for verification purposes.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This allows a ROM-able zImage to be written to eSD and for SuperH Mobile
ARM to boot directly from the SDHI hardware block.
This is achieved by the MaskROM loading the first portion of the image into
MERAM and then jumping to it. This portion contains loader code which
copies the entire image to SDRAM and jumps to it. From there the zImage
boot code proceeds as normal, uncompressing the image into its final
location and then jumping to it.
Cc: Paul Mundt <lethal@linux-sh.org>
Acked-by: Magnus Damm <magnus.damm@gmail.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It is easy to mis-maintain the proc_types table such that the
entries become wrongly-sized and misaligned when the kernel is
built in Thumb-2.
This patch adds an assembly-time check which will turn most common
size/alignment mistakes in this table into build failures, to avoid
having to debug the boot-time kernel hang which would happen if the
resulting kernel were actually booted.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit af3e4fd37a "ARM: 6859/1: Add writethrough dcache support for
ARM926EJS processor" broke Thumb2 compilation by omitting to maintain
the wide encoding for the added branch instructions which made the
ARM926EJ-S record smaller than expected, breaking the record walk code.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The ARM kernel supports writethrough data cache via the
CONFIG_CPU_DCACHE_WRITETHROUGH option. However, that
functionality wasn't implemented in the arch/arm/boot/compressed
code. It is now necessary due to a new ARM926EJS processor
that has an issue with writeback data cache.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
To be able to relocate the .bss section at run time independently from
the rest of the code, we must make sure that no GOTOFF relocations are
used with .bss symbols. This usually means that no global variables can
be marked static unless they're also const.
To enforce this, suffice to fail the build whenever a private symbol
is allocated to .bss and list those symbols for convenience.
The user_stack and user_stack_end labels in head.S were converted into
non exported symbols to remove false positives.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Russell King