932c435cab ("PCI: Add dev_flags bit to access VPD through function 0")
added PCI_DEV_FLAGS_VPD_REF_F0. Previously, we set the flag on every
non-zero function of quirked devices. If a function turned out to be
different from function 0, i.e., it had a different class, vendor ID, or
device ID, the flag remained set but we didn't make VPD accessible at all.
Flip this around so we only set PCI_DEV_FLAGS_VPD_REF_F0 for functions that
are identical to function 0, and allow regular VPD access for any other
functions.
[bhelgaas: changelog, stable tag]
Fixes: 932c435cab ("PCI: Add dev_flags bit to access VPD through function 0")
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Acked-by: Myron Stowe <myron.stowe@redhat.com>
Acked-by: Mark Rustad <mark.d.rustad@intel.com>
CC: stable@vger.kernel.org
On multi-function JMicron SATA/PATA/AHCI devices, the PATA controller at
function 1 doesn't work if it is powered on before the SATA controller at
function 0. The result is that PATA doesn't work after resume, and we
print messages like this:
pata_jmicron 0000:02:00.1: Refused to change power state, currently in D3
irq 17: nobody cared (try booting with the "irqpoll" option)
Async resume was introduced in v3.15 by 76569faa62 ("PM / sleep:
Asynchronous threads for resume_noirq"). Prior to that, we powered on
the functions in order, so this problem shouldn't happen.
e6b7e41cdd ("ata: Disabling the async PM for JMicron chip 363/361")
solved the problem for JMicron 361 and 363 devices. With async suspend
disabled, we always power on function 0 before function 1.
Barto then reported the same problem with a JMicron 368 (see comment #57 in
the bugzilla).
Rather than extending the blacklist piecemeal, disable async suspend for
all JMicron multi-function SATA/PATA/AHCI devices.
This quirk could stay in the ahci and pata_jmicron drivers, but it's likely
the problem will occur even if pata_jmicron isn't loaded until after the
suspend/resume. Making it a PCI quirk ensures that we'll preserve the
power-on order even if the drivers aren't loaded.
[bhelgaas: changelog, limit to multi-function, limit to IDE/ATA]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=81551
Reported-and-tested-by: Barto <mister.freeman@laposte.net>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.15+
Firmware typically configures the PCIe fabric with a consistent Max Payload
Size setting based on the devices present at boot. A hot-added device
typically has the power-on default MPS setting (128 bytes), which may not
match the fabric.
The previous Linux default, in the absence of any "pci=pcie_bus_*" options,
was PCIE_BUS_TUNE_OFF, in which we never touch MPS, even for hot-added
devices.
Add a new default setting, PCIE_BUS_DEFAULT, in which we make sure every
device's MPS setting matches the upstream bridge. This makes it more
likely that a hot-added device will work in a system with optimized MPS
configuration.
Note that if we hot-add a device that only supports 128-byte MPS, it still
likely won't work because we don't reconfigure the rest of the fabric.
Booting with "pci=pcie_bus_peer2peer" is a workaround for this because it
sets MPS to 128 for everything.
[bhelgaas: changelog, new default, rework for pci_configure_device() path]
Tested-by: Keith Busch <keith.busch@intel.com>
Tested-by: Jordan Hargrave <jharg93@gmail.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
* pci/hotplug:
PCI: pciehp: Remove ignored MRL sensor interrupt events
PCI: pciehp: Remove unused interrupt events
PCI: pciehp: Handle invalid data when reading from non-existent devices
PCI: Hold pci_slot_mutex while searching bus->slots list
PCI: Protect pci_bus->slots with pci_slot_mutex, not pci_bus_sem
PCI: pciehp: Simplify pcie_poll_cmd()
PCI: Use "slot" and "pci_slot" for struct hotplug_slot and struct pci_slot
* pci/iommu:
PCI: Remove pci_ats_enabled()
PCI: Stop caching ATS Invalidate Queue Depth
PCI: Move ATS declarations to linux/pci.h so they're all together
PCI: Clean up ATS error handling
PCI: Use pci_physfn() rather than looking up physfn by hand
PCI: Inline the ATS setup code into pci_ats_init()
PCI: Rationalize pci_ats_queue_depth() error checking
PCI: Reduce size of ATS structure elements
PCI: Embed ATS info directly into struct pci_dev
PCI: Allocate ATS struct during enumeration
iommu/vt-d: Cache PCI ATS state and Invalidate Queue Depth
* pci/irq:
PCI: Kill off set_irq_flags() usage
* pci/virtualization:
PCI: Add ACS quirks for Intel I219-LM/V
The Intel 100-series chipset now includes the integrated Ethernet as part
of a multifunction package. The Ethernet function does not include native
ACS support, but Intel confirms that the device is not capable of peer-to-
peer within the package. We can therefore quirk it to expose the
isolation.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: John Ronciak <john.ronciak@gmail.com>
The PCI capabilities list for Intel DH895xCC VFs (device id 0x0443) with
QuickAssist Technology is prematurely terminated in hardware.
Workaround the issue by hard-coding the known expected next capability
pointer and saving the PCIE cap into internal buffer.
Patch generated against cryptodev-2.6
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Set the PCI_DEV_FLAGS_VPD_REF_F0 flag on all Intel Ethernet device
functions other than function 0, so that on multi-function devices, we will
always read VPD from function 0 instead of from the other functions.
[bhelgaas: changelog]
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Alexander Duyck <alexander.h.duyck@redhat.com>
CC: stable@vger.kernel.org
Some quirks search for a HyperTransport capability and use a hard-coded TTL
value of 48 to avoid an infinite loop.
Move the definition of PCI_FIND_CAP_TTL to pci.h and use it instead of the
hard-coded TTL values.
[bhelgaas: changelog]
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCI class in dev->class is a three-byte value comprising a base class,
sub-class, and interface type. PCI_CLASS_NOT_DEFINED includes the base
class and sub-class, but not the interface type, so it should be shifted to
make space for the interface. It happens that PCI_CLASS_NOT_DEFINED is
zero, so it doesn't matter in the end, but we should still use it
consistently with other class definitions.
Treat PCI_CLASS_NOT_DEFINED as a base class/sub-class value that should
appear in bits 8-23 of dev->class.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Revert aeb30016fe ("PCI: add Intel USB specific reset method").
We checked for "dev->class == PCI_CLASS_SERIAL_USB", but dev->class
contains the entire three-byte base class/sub-class/interface, while
PCI_CLASS_SERIAL_USB is only the two-byte base class/sub-class.
This error meant that we used the Intel device-specific reset on devices
with class code 0x000c03 instead of those with class code 0x0c03xx.
0x000c03 is a reserved value in the 0x00 backwards compatibility base
class and shouldn't match any devices, so I think reset_intel_generic_dev()
always failed.
I considered adding a shift, but I can't test it, so it's as likely to
break something as to fix something.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Yu Zhao <yu.zhao@intel.com>
CC: Mathias Nyman <mathias.nyman@intel.com>
In fixup_ti816x_class(), we assigned "class = PCI_CLASS_MULTIMEDIA_VIDEO".
But PCI_CLASS_MULTIMEDIA_VIDEO is only the two-byte base class/sub-class
and needs to be shifted to make space for the low-order interface byte.
Shift PCI_CLASS_MULTIMEDIA_VIDEO to set the correct class code.
Fixes: 63c4408074 ("PCI: Add quirk for setting valid class for TI816X Endpoint")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Hemant Pedanekar <hemantp@ti.com>
In the generic quirk fixup_rev1_53c810(), added by a5312e28c1 ("[PATCH]
PCI: NCR 53c810 quirk"), we assigned "class = PCI_CLASS_STORAGE_SCSI". But
PCI_CLASS_STORAGE_SCSI is only the two-byte base class/sub-class and needs
to be shifted to make space for the low-order interface byte.
Furthermore, we had a similar quirk, pci_fixup_ncr53c810(), for arch/x86,
which assigned class correctly. The arch code is linked before the PCI
core, so arch quirks run before generic quirks. Therefore, on x86, the x86
arch quirk ran first, and the generic quirk did nothing because it saw that
dev->class was already set. But on other arches, the generic quirk set the
wrong class code.
Fix the generic quirk to set the correct class code and remove the
now-unnecessary x86-specific quirk.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Matthew Wilcox <matthew@wil.cx>
be6646bfba ("PCI: Prevent xHCI driver from claiming AMD Nolan USB3 DRD
device") added a quirk to override the PCI class code of the AMD Nolan
device.
Use PCI_CLASS_SERIAL_USB instead of a bare number to improve greppability.
Also add a log message about what we're doing.
No functional change except the new message.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Huang Rui <ray.huang@amd.com>
CC: Jason Chang <jason.chang@amd.com>
CC: Felipe Balbi <balbi@ti.com>
Intersil/Techwell TW686[4589]-based video capture cards have an empty
(zero) class code. Fix it.
Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Just like Haswell, Intel Atom Cherrytrail does not need the default 10ms
d3_delay imposed by the PCI specification.
Expand quirk_remove_d3_delay() to apply to Cherrytrail devices, so we can
ignore the 10ms delay before entering or exiting D3 suspend.
[bhelgaas: changelog, comment]
Signed-off-by: Srinidhi Kasagar <srinidhi.kasagar@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Marvell 9120 SATA controller has the same issue as a number of others, so
use the same quirk for this one. The other quirks were added by
cc346a4714 ("PCI: Add function 1 DMA alias quirk for Marvell devices").
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Intel confirms that 9-series chipset root ports provide ACS-equivalent
isolation when configured via the existing Intel PCH ACS quirk setup.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Don Dugger <donald.d.dugger@intel.com>
The PCI core now disables MSI and MSI-X for all devices during enumeration
regardless of CONFIG_PCI_MSI. Remove device-specific code to disable
MSI/MSI-X.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The SiS apic bug workaround is now obsolete as we cache the register
values for performance reasons.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: David Cohen <david.a.cohen@linux.intel.com>
Cc: Sander Eikelenboom <linux@eikelenboom.it>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dimitri Sivanich <sivanich@sgi.com>
Cc: Grant Likely <grant.likely@linaro.org>
Link: http://lkml.kernel.org/r/1428978610-28986-22-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* pci/misc:
PCI: Read capability list as dwords, not bytes
PCI: Don't clear ASPM bits when the FADT declares it's unsupported
PCI: Clarify policy for vendor IDs in pci.txt
PCI/ACPI: Optimize device state transition delays
PCI: Export pci_find_host_bridge() for use inside PCI core
PCI: Make a shareable UUID for PCI firmware ACPI _DSM
PCI: Fix typo in Thunderbolt kernel message
Intel has verified that there is no peer-to-peer between functions for the
below selection of 82580, 82576, 82575, I350, and 82571 multi-port devices.
This adds the necessary quirks to consider the functions isolated from each
other. 82571 quad-port devices are omitted due to likely lack of
ACS/isolation in the onboard switch, rendering quirks for the downstream
endpoints useless.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: John Ronciak <john.ronciak@intel.com>
Some AMD CS553x devices have read-only BARs because of a firmware or
hardware defect. There's a workaround in quirk_cs5536_vsa(), but it no
longer works after 36e8164882 ("PCI: Restore detection of read-only
BARs"). Prior to 36e8164882, we filled in res->start; afterwards we
leave it zeroed out. The quirk only updated the size, so the driver tried
to use a region starting at zero, which didn't work.
Expand quirk_cs5536_vsa() to read the base addresses from the BARs and
hard-code the sizes.
On Nix's system BAR 2's read-only value is 0x6200. Prior to 36e8164882,
we interpret that as a 512-byte BAR based on the lowest-order bit set. Per
datasheet sec 5.6.1, that BAR (MFGPT) requires only 64 bytes; use that to
avoid clearing any address bits if a platform uses only 64-byte alignment.
[bhelgaas: changelog, reduce BAR 2 size to 64]
Fixes: 36e8164882 ("PCI: Restore detection of read-only BARs")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=85991#c4
Link: http://support.amd.com/TechDocs/31506_cs5535_databook.pdf
Link: http://support.amd.com/TechDocs/33238G_cs5536_db.pdf
Reported-and-tested-by: Nix <nix@esperi.org.uk>
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v.2.6.27+
Intel has confirmed that the Wellsburg chipset, while not reporting ACS,
does provide the proper isolation through the RCBA/BSPR registers, so the
same quirk works for this set of device IDs.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Don Dugger <donald.d.dugger@intel.com>
The Adaptec 3405 is actually an Intel 80333 I/O processor where the exposed
device at 0e.0 is actually the address translation unit of the I/O
processor and a hidden, private device at 01.0 masters the DMA for the
device. Create a fixed alias between the exposed and hidden devfn so we
can enable the IOMMU.
Scenarios like this are potentially likely for any device incorporating
this I/O processor, so this little bit of abstraction with the fixed alias
table should make future additions trivial.
Without this fix, booting a system with the Intel IOMMU enabled and an
Adaptec 3405 at 02:0e.0 results in a flood of errors like this:
dmar: DRHD: handling fault status reg 3
dmar: DMAR:[DMA Write] Request device [02:01.0] fault addr ffbff000
DMAR:[fault reason 02] Present bit in context entry is clear
[bhelgaas: changelog, comment]
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Adaptec OEM Raid Solutions <aacraid@adaptec.com>
As Skyhawk and BE3-R (both multi-function devices) don't advertise the
PCI-ACS capability, the vfio driver places all the functions of these
devices in a single IOMMU group. Attaching (via PCI-passthru) two
different Skyhawk/BE3-R partitions (nPAR, Flex, etc. PFs) using vfio, to
different guests doesn't work as vfio only allows functions in *different*
IOMMU groups to be assigned to different guests.
As peer-to-peer access between PFs in Skyhawk/BE3-R is not possible, we can
treat them as "fully isolated" even though the device doesn't advertise
ACS. Add a PCI quirk for Skyhawk and BE3-R chips to fix this problem.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Some AMD/ATI GPUs report NoSoftRst- to indicate that they perform a reset
when software transitions them from D3hot to D0, but there is no apparent
effect on the device: the monitor remains synced and the framebuffer
contents are retained.
Callers of pci_reset_function() don't necessarily have a way to validate
whether a reset was effective, so we don't want to rely on NoSoftRst if
it's known to be inaccurate. Returning an error in such cases appears to
be the better option. For users like vfio-pci, this allows the driver to
escalate to the bus reset interfaces.
If a device lives on the root bus, there's really no further
escalation path, so we exempt PM reset as potentially better than
nothing.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reports against the TL-WDN4800 card indicate that PCI bus reset of this
Atheros device cause system lock-ups and resets. I've also been able to
confirm this behavior on multiple systems. The device never returns from
reset and attempts to access config space of the device after reset result
in hangs. Blacklist bus reset for the device to avoid this issue.
[bhelgaas: This regression appeared in v3.14. Andreas bisected it to
425c1b223d ("PCI: Add Virtual Channel to save/restore support"), but we
don't understand the mechanism by which that commit affects the reset
path.]
[bhelgaas: changelog, references]
Link: http://lkml.kernel.org/r/20140923210318.498dacbd@dualc.maya.org
Reported-by: Andreas Hartmann <andihartmann@freenet.de>
Tested-by: Andreas Hartmann <andihartmann@freenet.de>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.14+
The AMD Nolan (NL) SoC contains a DesignWare USB3 Dual-Role Device that can
be operated either as a USB Host or a USB Device. In the AMD NL platform,
this device ([1022:7912]) has a class code of PCI_CLASS_SERIAL_USB_XHCI
(0x0c0330), which means the xhci driver will claim it.
But the dwc3 driver is a more specific driver for this device, and we'd
prefer to use it instead of xhci. To prevent xhci from claiming the
device, change the class code to 0x0c03fe, which the PCI r3.0 spec defines
as "USB device (not host controller)". The dwc3 driver can then claim it
based on its Vendor and Device ID.
Suggested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jason Chang <jason.chang@amd.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
AMD has confirmed that peer-to-peer between two southbridge functions does
not occur.
Add a quirk to indicate that these functions are isolated even though they
don't have an ACS capability.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=81841
Signed-off-by: Marti Raudsepp <marti@juffo.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Joel Schopp <joel.schopp@amd.com>
Intel has verified there is no peer-to-peer between functions for the below
selection of 82598, 82599, and X520 10G NICs. These NICs lack an ACS
capability, so we're not able to determine this isolation without the help
of quirks.
Generalize the Solarflare quirk and add these Intel 10G NICs.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: John Ronciak <John.ronciak@intel.com>
Solarflare confirms that these devices do not allow peer-to-peer between
functions. Quirk them to allow IOMMU grouping to expose this isolation.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Robert Stonehouse <rstonehouse@solarflare.com>
pci_get_dma_source() is unused, so remove it. We now have
dma_alias_devfn() to describe this.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/enumeration:
PCI: Enable CRS Software Visibility for root port if it is supported
PCI: Check only the Vendor ID to identify Configuration Request Retry
* pci/misc:
PCI: Parenthesize PCI_DEVID and PCI_VPD_LRDT_ID parameters
PCI: Increase IBM ipr SAS Crocodile BARs to at least system page size
PCI/AER: Make <linux/aer.h> standalone includable
* pci/virtualization:
PCI: Use device flag helper functions
xen/pciback: Use PCI device flag helper functions
KVM: Use PCI device flag helper functions
PCI: Add device flag helper functions
PCI: Assume all Mellanox devices have broken INTx masking
The Crocodile chip occasionally comes up with 4k and 8k BAR sizes. Due to
an erratum, setting the SR-IOV page size causes the physical function BARs
to expand to the system page size. Since ppc64 uses 64k pages, when Linux
tries to assign the smaller resource sizes to the now 64k BARs the address
will be truncated and the BARs will overlap.
Force Linux to allocate the resource as a full page, which avoids the
overlap.
[bhelgaas: print expanded resource, too]
Signed-off-by: Douglas Lehr <dllehr@us.ibm.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Milton Miller <miltonm@us.ibm.com>
CC: stable@vger.kernel.org
The VFIO driver routes LSI interrupts by capturing, masking, and then
delivering. When passing though Mellanox adapters from host to guest,
interrupt storm are reported from host and guest. That's because the PCI
command register INTx Disable bit doesn't work on Mellanox devices.
# lspci | grep Mellanox
0001:05:00.0 Ethernet controller: Mellanox Technologies MT27500 Family [ConnectX-3]
0005:01:00.0 Ethernet controller: Mellanox Technologies MT26448 [ConnectX EN 10GigE, PCIe 2.0 5GT/s] (rev b0)
Amir Vadai confirmed that all Mellanox devices have same problem.
The patch marks broken INTx masking for all Mellanox adapters.
Suggested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-By: Amir Vadai <amirv@mellanox.com>
Here's the big driver misc / char pull request for 3.17-rc1.
Lots of things in here, the thunderbolt support for Apple laptops, some
other new drivers, testing fixes, and other good things. All have been
in linux-next for a long time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlPf1LcACgkQMUfUDdst+ymaVwCgqMrKFmpduBufOSFROhxlfB5Q
ajsAoNDmIn3pgla+kj23Y5ib20aMi++s
=IdIr
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc driver patches from Greg KH:
"Here's the big driver misc / char pull request for 3.17-rc1.
Lots of things in here, the thunderbolt support for Apple laptops,
some other new drivers, testing fixes, and other good things. All
have been in linux-next for a long time"
* tag 'char-misc-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (119 commits)
misc: bh1780: Introduce the use of devm_kzalloc
Lattice ECP3 FPGA: Correct endianness
drivers/misc/ti-st: Load firmware from ti-connectivity directory.
dt-bindings: extcon: Add support for SM5502 MUIC device
extcon: sm5502: Change internal hardware switch according to cable type
extcon: sm5502: Detect cable state after completing platform booting
extcon: sm5502: Add support new SM5502 extcon device driver
extcon: arizona: Get MICVDD against extcon device
extcon: Remove unnecessary OOM messages
misc: vexpress: Fix sparse non static symbol warnings
mei: drop unused hw dependent fw status functions
misc: bh1770glc: Use managed functions
pcmcia: remove DEFINE_PCI_DEVICE_TABLE usage
misc: remove DEFINE_PCI_DEVICE_TABLE usage
ipack: Replace DEFINE_PCI_DEVICE_TABLE macro use
drivers/char/dsp56k.c: drop check for negativity of unsigned parameter
mei: fix return value on disconnect timeout
mei: don't schedule suspend in pm idle
mei: start disconnect request timer consistently
mei: reset client connection state on timeout
...
This bridge sometimes shows up as a root complex device and sometimes as a
discrete PCIe-to-PCI bridge. Testing indicates that in the latter case, we
need to enable the PCIe bridge DMA alias quirk.
Reported-by: Milos Kaurin <milos.kaurin@gmail.com>
Tested-by: Milos Kaurin <milos.kaurin@gmail.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add two quirks to support thunderbolt suspend/resume on Apple systems.
We need to perform two different actions during suspend and resume:
The whole controller has to be powered down before suspend. If this is
not done then the native host interface device will be gone after resume
if a thunderbolt device was plugged in before suspending. The controller
represents itself as multiple PCI devices/bridges. To power it down we
hook into the upstream bridge of the controller and call the magic ACPI
methods. Power will be restored automatically during resume (by the
firmware presumably).
During resume we have to wait for the native host interface to
reestablish all pci tunnels. Since there is no parent-child relationship
between the NHI and the bridges we have to explicitly wait for them
using device_pm_wait_for_dev. We do this in the resume_noirq phase of
the downstream bridges of the controller (which lead into the
thunderbolt tunnels).
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add pci_fixup_suspend_late as a new pci_fixup_pass. The pass is called
from suspend_noirq and poweroff_noirq. Using the same pass for suspend
and hibernate is consistent with resume_early which is called by
resume_noirq and restore_noirq.
The new quirk pass is required for Thunderbolt support on Apple
hardware.
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alex Williamson