This patch adds support for setting up an SG table used by the
TMC ETR inbuilt SG unit. The TMC ETR uses 4K page sized tables
to hold pointers to the 4K data pages with the last entry in a
table pointing to the next table with the entries, by kind of
chaining. The 2 LSBs determine the type of the table entry, to
one of :
Normal - Points to a 4KB data page.
Last - Points to a 4KB data page, but is the last entry in the
page table.
Link - Points to another 4KB table page with pointers to data.
The code takes care of handling the system page size which could
be different than 4K. So we could end up putting multiple ETR
SG tables in a single system page, vice versa for the data pages.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch introduces a generic sg table data structure and
associated operations. An SG table can be used to map a set
of Data pages where the trace data could be stored by the TMC
ETR. The information about the data pages could be stored in
different formats, depending on the type of the underlying
SG mechanism (e.g, TMC ETR SG vs Coresight CATU). The generic
structure provides book keeping of the pages used for the data
as well as the table contents. The table should be filled by
the user of the infrastructure.
A table can be created by specifying the number of data pages
as well as the number of table pages required to hold the
pointers, where the latter could be different for different
types of tables. The pages are mapped in the appropriate dma
data direction mode (i.e, DMA_TO_DEVICE for table pages
and DMA_FROM_DEVICE for data pages). The framework can optionally
accept a set of allocated data pages (e.g, perf ring buffer) and
map them accordingly. The table and data pages are vmap'ed to allow
easier access by the drivers. The framework also provides helpers to
sync the data written to the pages with appropriate directions.
This will be later used by the TMC ETR SG unit and CATU.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We are about to add the support for ETR builtin scatter-gather mode
for dealing with large amount of trace buffers. However, on some of
the platforms, using the ETR SG mode can lock up the system due to
the way the ETR is connected to the memory subsystem.
In SG mode, the ETR performs READ from the scatter-gather table to
fetch the next page and regular WRITE of trace data. If the READ
operation doesn't complete(due to the memory subsystem issues,
which we have seen on a couple of platforms) the trace WRITE
cannot proceed leading to issues. So, we by default do not
use the SG mode, unless it is known to be safe on the platform.
We define a DT property for the TMC node to specify whether we
have a proper SG mode.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Mike Leach <mike.leach@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: John Horley <john.horley@arm.com>
Cc: Robert Walker <robert.walker@arm.com>
Cc: devicetree@vger.kernel.org
Cc: frowand.list@gmail.com
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Right now we open code filling the trace buffer with synchronization
packets when the circular buffer wraps around in different drivers.
Move this to a common place. While at it, clean up the barrier_pkt
array to strip off the trailing '\0'.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Mike Leach <mike.leach@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We don't support ETR in perf mode yet. So, don't
even try to enable the hardware, even by mistake.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We zero out the entire trace buffer used for ETR before it is enabled,
for helping with debugging. With the addition of scatter-gather mode,
the buffer could be bigger and non-contiguous.
Get rid of this step; if someone wants to debug, they can always add it
as and when needed.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At the moment we adjust the buffer pointers for reading the trace
data via misc device in the common code for ETF/ETB and ETR. Since
we are going to change how we manage the buffer for ETR, let us
move the buffer manipulation to the respective driver files, hiding
it from the common code. We do so by adding type specific helpers
for finding the length of data and the pointer to the buffer,
for a given length at a file position.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add ETM PIDs of the Arm cortex-A CPUs to the white list of ETMs.
While at it add a helper macro to make it easier to add the new
entries.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As with ETM3x, the ETM4x tracers can trigger trace acquisition based on
contextID value, something that isn't useful when PID namespaces are
enabled. Indeed the PID value of a process has a different representation
in the kernel and the PID namespace, making the feature confusing and
potentially leaking internal kernel information.
As such simply return an error when the feature is being used from a
PID namespace other than the default one.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Kim Phillips <kim.phillips@arm.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tracers can trigger trace acquisition based on contextID value, something
that isn't useful when PID namespaces are enabled. Indeed the PID value
of a process has a different representation in the kernel and the PID
namespace, making the feature confusing and potentially leaking internal
kernel information.
As such simply return an error when the feature is being used from a
PID namespace other than the default one.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Kim Phillips <kim.phillips@arm.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the "big" char and misc driver patches for 4.18-rc1.
It's not a lot of stuff here, but there are some highlights:
- coreboot driver updates
- soundwire driver updates
- android binder updates
- fpga big sync, mostly documentation
- lots of minor driver updates
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWxbXfQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymwCACdFbUy2kWwrpZWSfSBpawfrs75lLMAmwVOe+62
9aDsDWzDVUEFxF20qiE6
=CMJ3
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the "big" char and misc driver patches for 4.18-rc1.
It's not a lot of stuff here, but there are some highlights:
- coreboot driver updates
- soundwire driver updates
- android binder updates
- fpga big sync, mostly documentation
- lots of minor driver updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (81 commits)
vmw_balloon: fixing double free when batching mode is off
MAINTAINERS: Add driver-api/fpga path
fpga: clarify that unregister functions also free
documentation: fpga: move fpga-region.txt to driver-api
documentation: fpga: add bridge document to driver-api
documentation: fpga: move fpga-mgr.txt to driver-api
Documentation: fpga: move fpga overview to driver-api
fpga: region: kernel-doc fixes
fpga: bridge: kernel-doc fixes
fpga: mgr: kernel-doc fixes
fpga: use SPDX
fpga: region: change api, add fpga_region_create/free
fpga: bridge: change api, don't use drvdata
fpga: manager: change api, don't use drvdata
fpga: region: don't use drvdata in common fpga code
Drivers: hv: vmbus: Removed an unnecessary cast from void *
ver_linux: Drop redundant calls to system() to test if file is readable
ver_linux: Move stderr redirection from function parameter to function body
misc: IBM Virtual Management Channel Driver (VMC)
rpmsg: Correct support for MODULE_DEVICE_TABLE()
...
Commit b5e2ced9bf ("stm class: Use vmalloc for the master map") caused
a build error on some arches as vmalloc.h was not explicitly included.
Fix that by adding it to the list of includes.
Fixes: b5e2ced9bf ("stm class: Use vmalloc for the master map")
Reported-by: kbuild test robot <lkp@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit d5c435df4a ("intel_th: msu: Use the real device in case of IOMMU
domain allocation") changes dma buffer allocation to use the actual
underlying device, but forgets to change the deallocation path, which leads
to (if you've got CAP_SYS_RAWIO):
> # echo 0,0 > /sys/bus/intel_th/devices/0-msc0/nr_pages
> ------------[ cut here ]------------
> kernel BUG at ../linux/drivers/iommu/intel-iommu.c:3670!
> CPU: 3 PID: 231 Comm: sh Not tainted 4.17.0-rc1+ #2729
> RIP: 0010:intel_unmap+0x11e/0x130
...
> Call Trace:
> intel_free_coherent+0x3e/0x60
> msc_buffer_win_free+0x100/0x160 [intel_th_msu]
This patch fixes the buffer deallocation code to use the correct device.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Fixes: d5c435df4a ("intel_th: msu: Use the real device in case of IOMMU domain allocation")
Reported-by: Baofeng Tian <baofeng.tian@intel.com>
CC: stable@vger.kernel.org # v4.14+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fengguang is running into a warning from the buddy allocator:
> swapper/0: page allocation failure: order:9, mode:0x14040c0(GFP_KERNEL|__GFP_COMP), nodemask=(null)
> CPU: 1 PID: 1 Comm: swapper/0 Not tainted 4.17.0-rc1 #262
> Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1 04/01/2014
> Call Trace:
...
> __kmalloc+0x14b/0x180: ____cache_alloc at mm/slab.c:3127
> stm_register_device+0xf3/0x5c0: stm_register_device at drivers/hwtracing/stm/core.c:695
...
Which is basically a result of the stm class trying to allocate ~512kB
for the dummy_stm with its default parameters. There's no reason, however,
for it not to be vmalloc()ed instead, which is what this patch does.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
CC: stable@vger.kernel.org # v4.4+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver prints pcsr twice: the first time it uses specifier %px to
print hexadecimal pcsr value and the second time uses specifier %pS for
output kernel symbols.
As suggested by Kees, using %pS should be sufficient and %px isn't
necessary; the reason is if the pcsr is a kernel space address, we can
easily get to know the code line from %pS format, on the other hand, if
the pcsr value doesn't fall into kernel space range (e.g. if the CPU is
stuck in firmware), %pS also gives out pcsr hexadecimal value.
So this commit removes useless %px and update section "Output format"
in the document for alignment between the code and document.
Suggested-by: Kees Cook <keescook@chromium.org>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The simple removal of an extra newline, no change in functionality.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variable 'paddr' can't be used if uninitialised but is nonetheless
confusing to some static checker. As such simply initialise it to zero.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While operating from sysFS the TMC-ETR driver needs to make sure it has
memory to work with but doesn't allocate memory uselessly either. Since
the main memory handle for this driver is drvdata::vaddr, use it throughout
function tmc_enable_etr_sink_sysfs() so that things are consistent.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Moving all kernel side CoreSight framework and drivers to SPDX identifier.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Never directly free @dev after calling device_register(), even
if it returned an error. Always use put_device() to give up the
reference initialized.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of char/misc driver patches for 4.17-rc1.
There are a lot of little things in here, nothing huge, but all
important to the different hardware types involved:
- thunderbolt driver updates
- parport updates (people still care...)
- nvmem driver updates
- mei updates (as always)
- hwtracing driver updates
- hyperv driver updates
- extcon driver updates
- and a handfull of even smaller driver subsystem and individual
driver updates
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWsShSQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykNqwCfUbfvopswb1PesHCLABDBsFQChgoAniDa6pS9
kI8TN5MdLN85UU27Mkb6
=BzFR
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc updates from Greg KH:
"Here is the big set of char/misc driver patches for 4.17-rc1.
There are a lot of little things in here, nothing huge, but all
important to the different hardware types involved:
- thunderbolt driver updates
- parport updates (people still care...)
- nvmem driver updates
- mei updates (as always)
- hwtracing driver updates
- hyperv driver updates
- extcon driver updates
- ... and a handful of even smaller driver subsystem and individual
driver updates
All of these have been in linux-next with no reported issues"
* tag 'char-misc-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (149 commits)
hwtracing: Add HW tracing support menu
intel_th: Add ACPI glue layer
intel_th: Allow forcing host mode through drvdata
intel_th: Pick up irq number from resources
intel_th: Don't touch switch routing in host mode
intel_th: Use correct method of finding hub
intel_th: Add SPDX GPL-2.0 header to replace GPLv2 boilerplate
stm class: Make dummy's master/channel ranges configurable
stm class: Add SPDX GPL-2.0 header to replace GPLv2 boilerplate
MAINTAINERS: Bestow upon myself the care for drivers/hwtracing
hv: add SPDX license id to Kconfig
hv: add SPDX license to trace
Drivers: hv: vmbus: do not mark HV_PCIE as perf_device
Drivers: hv: vmbus: respect what we get from hv_get_synint_state()
/dev/mem: Avoid overwriting "err" in read_mem()
eeprom: at24: use SPDX identifier instead of GPL boiler-plate
eeprom: at24: simplify the i2c functionality checking
eeprom: at24: fix a line break
eeprom: at24: tweak newlines
eeprom: at24: refactor at24_probe()
...
This is a cosmetic patch that deals with the address filter structure's
ambiguous fields 'filter' and 'range'. The former stands to mean that the
filter's *action* should be to filter the traces to its address range if
it's set or stop tracing if it's unset. This is confusing and hard on the
eyes, so this patch replaces it with 'action' enum. The 'range' field is
completely redundant (meaning that the filter is an address range as
opposed to a single address trigger), as we can use zero size to mean the
same thing.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: Will Deacon <will.deacon@arm.com>
Link: http://lkml.kernel.org/r/20180329120648.11902-1-alexander.shishkin@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
These are:
* Mass conversion to GPL-2 SPDX header
* Moved "hwtracing" to now its own submenu, to uncrowd the parent menu a bit
* Added MAINTAINERS entry for drivers/hwtracing
* Somewhat small Trace Hub fixes
* Added ACPI glue layer for the Trace Hub
* Added more module parameters to dummy_stm for better test coverage
-----BEGIN PGP SIGNATURE-----
iJkEABEIAEEWIQQSviFCoXpKPDNATbnrxfYkYwVX/wUCWrzG7yMcYWxleGFuZGVy
LnNoaXNoa2luQGxpbnV4LmludGVsLmNvbQAKCRDrxfYkYwVX/0jcAQCE/maw6L5P
NdT3Ck3EuDWzij9uimq3Y0UyI9F4Cd+vYgD+N8Skyiua+NqfBGB0oXNsJt2acirg
O3G990RK9dX4H2c=
=CuGw
-----END PGP SIGNATURE-----
Merge tag 'stm-intel_th-for-greg-20180329' of git://git.kernel.org/pub/scm/linux/kernel/git/ash/stm into char-misc-next
Alexander writes:
stm class/intel_th: Updates for 4.17
These are:
* Mass conversion to GPL-2 SPDX header
* Moved "hwtracing" to now its own submenu, to uncrowd the parent menu a bit
* Added MAINTAINERS entry for drivers/hwtracing
* Somewhat small Trace Hub fixes
* Added ACPI glue layer for the Trace Hub
* Added more module parameters to dummy_stm for better test coverage
Make a "HW tracing support" menu and move 2 entries into it.
(No change in Coresight, which is ARM-specific and is only listed for
ARM & ARM64.)
This makes the Device Drivers menu more consistent and prevents these
drivers from being listed at the top level of the Device Drivers menu.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
The Trace Hub devices now can be enumerated as ACPI devices, which
translates into "Host Debugger mode". There are two IDs: one for
PCH Trace Hub, and one for the uncore Trace Hub. These are expected
to stay the same across all platforms.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Some devices can only operate in host mode, so we need means of
communicating this to the core driver on per-device basis. This
adds a flag to drvdata to signal host-only capability to the core.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Platform devices pass their IRQs around as resources, so as a convenience
for the glue layer code, allow them pass the IRQ to the core driver in
the resources array.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
When the Trace Hub is operating in Host Debugger mode, it is up to the
debugger to configure master routing even for the software sources. Do
not do this in the driver in this case.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Since commit 8edc514b01 ("intel_th: Make SOURCE devices children of the
root device") the hub is not the parent of SOURCE devices any more, so the
new helper function should be used for that instead of always using the
parent. The intel_th_set_output() path, however, still uses the old
logic, leading to the hub driver structure being aliased with something
else, like struct pci_driver or struct acpi_driver, and an incorrect call
to an address inferred from that, potentially resulting in a crash.
Fixes: 8edc514b01 ("intel_th: Make SOURCE devices children of the root device")
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
This adds SPDX GPL-2.0 header to the Trace Hub driver and removes the
GPLv2 boilerplate text.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
To allow for more flexible testing of the stm class, make it possible
to specify the ranges of masters and channels that the dummy_stm devices
cover. This is done via module parameters.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
This adds SPDX GPL-2.0 header to to stm core files and removes the
GPLv2 boilerplate text.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
ctxid_pid and vmid_val in config are of type u64. When an integer
0xFF is being left shifted more than 32 bits, the behavior is
undefined. The fix is to specify 0xFF as an unsigned long.
Detected by Coverity scan: CID 37650, 37651 (Bad bit shift operation)
Signed-off-by: Bo Yan <byan@nvidia.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit ad67b74d24 ("printk: hash addresses printed with %p") lets
printk specifier %p to hash all addresses before printing, this was
resulting in the high 32 bits of pcsr can only output zeros. So
module cannot completely print pc value and it's pointless for debugging
purpose.
This patch fixes this by using %px to print pcsr instead.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big pull request for char/misc drivers for 4.16-rc1.
There's a lot of stuff in here. Three new driver subsystems were added
for various types of hardware busses:
- siox
- slimbus
- soundwire
as well as a new vboxguest subsystem for the VirtualBox hypervisor
drivers.
There's also big updates from the FPGA subsystem, lots of Android binder
fixes, the usual handful of hyper-v updates, and lots of other smaller
driver updates.
All of these have been in linux-next for a long time, with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWnLuZw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynS4QCcCrPmwfD5PJwaF+q2dPfyKaflkQMAn0x6Wd+u
Gw3Z2scgjETUpwJ9ilnL
=xcQ0
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big pull request for char/misc drivers for 4.16-rc1.
There's a lot of stuff in here. Three new driver subsystems were added
for various types of hardware busses:
- siox
- slimbus
- soundwire
as well as a new vboxguest subsystem for the VirtualBox hypervisor
drivers.
There's also big updates from the FPGA subsystem, lots of Android
binder fixes, the usual handful of hyper-v updates, and lots of other
smaller driver updates.
All of these have been in linux-next for a long time, with no reported
issues"
* tag 'char-misc-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (155 commits)
char: lp: use true or false for boolean values
android: binder: use VM_ALLOC to get vm area
android: binder: Use true and false for boolean values
lkdtm: fix handle_irq_event symbol for INT_HW_IRQ_EN
EISA: Delete error message for a failed memory allocation in eisa_probe()
EISA: Whitespace cleanup
misc: remove AVR32 dependencies
virt: vbox: Add error mapping for VERR_INVALID_NAME and VERR_NO_MORE_FILES
soundwire: Fix a signedness bug
uio_hv_generic: fix new type mismatch warnings
uio_hv_generic: fix type mismatch warnings
auxdisplay: img-ascii-lcd: add missing MODULE_DESCRIPTION/AUTHOR/LICENSE
uio_hv_generic: add rescind support
uio_hv_generic: check that host supports monitor page
uio_hv_generic: create send and receive buffers
uio: document uio_hv_generic regions
doc: fix documentation about uio_hv_generic
vmbus: add monitor_id and subchannel_id to sysfs per channel
vmbus: fix ABI documentation
uio_hv_generic: use ISR callback method
...
- Security mitigations:
- variant 2: invalidating the branch predictor with a call to secure firmware
- variant 3: implementing KPTI for arm64
- 52-bit physical address support for arm64 (ARMv8.2)
- arm64 support for RAS (firmware first only) and SDEI (software
delegated exception interface; allows firmware to inject a RAS error
into the OS)
- Perf support for the ARM DynamIQ Shared Unit PMU
- CPUID and HWCAP bits updated for new floating point multiplication
instructions in ARMv8.4
- Removing some virtual memory layout printks during boot
- Fix initial page table creation to cope with larger than 32M kernel
images when 16K pages are enabled
-----BEGIN PGP SIGNATURE-----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=iEjP
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Catalin Marinas:
"The main theme of this pull request is security covering variants 2
and 3 for arm64. I expect to send additional patches next week
covering an improved firmware interface (requires firmware changes)
for variant 2 and way for KPTI to be disabled on unaffected CPUs
(Cavium's ThunderX doesn't work properly with KPTI enabled because of
a hardware erratum).
Summary:
- Security mitigations:
- variant 2: invalidate the branch predictor with a call to
secure firmware
- variant 3: implement KPTI for arm64
- 52-bit physical address support for arm64 (ARMv8.2)
- arm64 support for RAS (firmware first only) and SDEI (software
delegated exception interface; allows firmware to inject a RAS
error into the OS)
- perf support for the ARM DynamIQ Shared Unit PMU
- CPUID and HWCAP bits updated for new floating point multiplication
instructions in ARMv8.4
- remove some virtual memory layout printks during boot
- fix initial page table creation to cope with larger than 32M kernel
images when 16K pages are enabled"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (104 commits)
arm64: Fix TTBR + PAN + 52-bit PA logic in cpu_do_switch_mm
arm64: Turn on KPTI only on CPUs that need it
arm64: Branch predictor hardening for Cavium ThunderX2
arm64: Run enable method for errata work arounds on late CPUs
arm64: Move BP hardening to check_and_switch_context
arm64: mm: ignore memory above supported physical address size
arm64: kpti: Fix the interaction between ASID switching and software PAN
KVM: arm64: Emulate RAS error registers and set HCR_EL2's TERR & TEA
KVM: arm64: Handle RAS SErrors from EL2 on guest exit
KVM: arm64: Handle RAS SErrors from EL1 on guest exit
KVM: arm64: Save ESR_EL2 on guest SError
KVM: arm64: Save/Restore guest DISR_EL1
KVM: arm64: Set an impdef ESR for Virtual-SError using VSESR_EL2.
KVM: arm/arm64: mask/unmask daif around VHE guests
arm64: kernel: Prepare for a DISR user
arm64: Unconditionally enable IESB on exception entry/return for firmware-first
arm64: kernel: Survive corrected RAS errors notified by SError
arm64: cpufeature: Detect CPU RAS Extentions
arm64: sysreg: Move to use definitions for all the SCTLR bits
arm64: cpufeature: __this_cpu_has_cap() shouldn't stop early
...
Reuse the new generic helper, of_cpu_node_to_id() to map a
given CPU phandle to a logical CPU number.
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Tested-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
These duplicate includes have been found with scripts/checkincludes.pl but
they have been removed manually to avoid removing false positives.
Signed-off-by: Pravin Shedge <pravin.shedge4linux@gmail.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CoreSight TPIU should be disabled when tracing to other sinks to allow
them to operate at full bandwidth.
This patch fixes tpiu_disable_hw() to correctly disable the TPIU by
configuring the TPIU to stop on flush, initiating a manual flush, waiting
for the flush to complete and then waits for the TPIU to indicate it has
stopped.
Signed-off-by: Robert Walker <robert.walker@arm.com>
Tested-by: Mike Leach <mike.leach@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix ptr_ret.cocci warnings:
drivers/hwtracing/coresight/coresight-tpiu.c:163:1-3: WARNING: PTR_ERR_OR_ZERO can be used
drivers/hwtracing/coresight/coresight-funnel.c:217:1-3: WARNING: PTR_ERR_OR_ZERO can be used
drivers/hwtracing/coresight/coresight-dynamic-replicator.c:166:1-3: WARNING: PTR_ERR_OR_ZERO can be used
Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR
Generated by: scripts/coccinelle/api/ptr_ret.cocci
Signed-off-by: Vasyl Gomonovych <gomonovych@gmail.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No need to reinvent the wheel, we have bus_find_device_by_name().
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By passing an export descriptor to the write function, users don't need to
keep a global static pointer and can rely on container_of() to fetch their
own structure.
Link: http://lkml.kernel.org/r/20170602102025.5140-1-felipe.balbi@linux.intel.com
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Reviewed-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Here is the big set of char/misc and other driver subsystem patches for
4.15-rc1.
There are small changes all over here, hyperv driver updates, pcmcia
driver updates, w1 driver updats, vme driver updates, nvmem driver
updates, and lots of other little one-off driver updates as well. The
shortlog has the full details.
Note, there will be a merge conflict in drivers/misc/lkdtm_core.c when
merging to your tree as one lkdtm patch came in through the perf tree as
well as this one. The resolution is to take the const change that this
tree provides.
All of these have been in linux-next for quite a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWg2Lnw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymTUwCgwp46+I8yPlgDH8oe5TxyyJnpdHQAn1XW0i+a
sBi6WS87In5v1QO1Rgfc
=dH2a
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.15-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc updates from Greg KH:
"Here is the big set of char/misc and other driver subsystem patches
for 4.15-rc1.
There are small changes all over here, hyperv driver updates, pcmcia
driver updates, w1 driver updats, vme driver updates, nvmem driver
updates, and lots of other little one-off driver updates as well. The
shortlog has the full details.
All of these have been in linux-next for quite a while with no
reported issues"
* tag 'char-misc-4.15-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (90 commits)
VME: Return -EBUSY when DMA list in use
w1: keep balance of mutex locks and refcnts
MAINTAINERS: Update VME subsystem tree.
nvmem: sunxi-sid: add support for A64/H5's SID controller
nvmem: imx-ocotp: Update module description
nvmem: imx-ocotp: Enable i.MX7D OTP write support
nvmem: imx-ocotp: Add i.MX7D timing write clock setup support
nvmem: imx-ocotp: Move i.MX6 write clock setup to dedicated function
nvmem: imx-ocotp: Add support for banked OTP addressing
nvmem: imx-ocotp: Pass parameters via a struct
nvmem: imx-ocotp: Restrict OTP write to IMX6 processors
nvmem: uniphier: add UniPhier eFuse driver
dt-bindings: nvmem: add description for UniPhier eFuse
nvmem: set nvmem->owner to nvmem->dev->driver->owner if unset
nvmem: qfprom: fix different address space warnings of sparse
nvmem: mtk-efuse: fix different address space warnings of sparse
nvmem: mtk-efuse: use stack for nvmem_config instead of malloc'ing it
nvmem: imx-iim: use stack for nvmem_config instead of malloc'ing it
thunderbolt: tb: fix use after free in tb_activate_pcie_devices
MAINTAINERS: Add git tree for Thunderbolt development
...
- proper use of the bool type (Thomas Meyer)
- constification of struct config_item_type (Bhumika Goyal)
-----BEGIN PGP SIGNATURE-----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=+tMO
-----END PGP SIGNATURE-----
Merge tag 'configfs-for-4.15' of git://git.infradead.org/users/hch/configfs
Pull configfs updates from Christoph Hellwig:
"A couple of configfs cleanups:
- proper use of the bool type (Thomas Meyer)
- constification of struct config_item_type (Bhumika Goyal)"
* tag 'configfs-for-4.15' of git://git.infradead.org/users/hch/configfs:
RDMA/cma: make config_item_type const
stm class: make config_item_type const
ACPI: configfs: make config_item_type const
nvmet: make config_item_type const
usb: gadget: configfs: make config_item_type const
PCI: endpoint: make config_item_type const
iio: make function argument and some structures const
usb: gadget: make config_item_type structures const
dlm: make config_item_type const
netconsole: make config_item_type const
nullb: make config_item_type const
ocfs2/cluster: make config_item_type const
target: make config_item_type const
configfs: make ci_type field, some pointers and function arguments const
configfs: make config_item_type const
configfs: Fix bool initialization/comparison
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per coresight standards, PIDR2 register has the following format :
[2-0] - JEP106_bits6to4
[3] - JEDEC, designer ID is specified by JEDEC.
However some of the drivers only use mask of 0x3 for the PIDR2 leaving
bits [3-2] unchecked, which could potentially match the component for
a different device altogether. This patch fixes the mask and the
corresponding id bits for the existing devices.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make config_item_type structures const as they are either passed to a
function having the argument as const or used inside a if statement or
stored in the const "ci_type" field of a config_item structure.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This adds Intel(R) Trace Hub PCI ID for Lewisburg PCH.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds Intel(R) Trace Hub PCI ID for Cedar Fork PCH.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For reasons unknown, the stm_source removal path uses device_destroy()
to kill the underlying device object. Because device_destroy() uses
devt to look for the device to destroy and the fact that stm_source
devices don't have one (or all have the same one), it just picks the
first device in the class, which may well be the wrong one.
That is, loading stm_console and stm_heartbeat and then removing both
will die in dereferencing a freed object.
Since this should have been device_unregister() in the first place,
use it instead of device_destroy().
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Fixes: 7bd1d4093c ("stm class: Introduce an abstraction for System Trace Module devices")
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel TH:
* Updated subdevice management code to better fit host mode
* Added support for Low Power Path (LPP) output type
* Fixed memory allocation with IOMMU enabled (DMAR tables)
* Added Cannon Lake PCH PCI IDs
* Added a quirk to force time sync on devices that need it
STM:
* Fixed potential read overflow in ioctl()
* Documented stm_ftrace source.
-----BEGIN PGP SIGNATURE-----
iJkEABEIAEEWIQQSviFCoXpKPDNATbnrxfYkYwVX/wUCWaBJXyMcYWxleGFuZGVy
LnNoaXNoa2luQGxpbnV4LmludGVsLmNvbQAKCRDrxfYkYwVX/+4vAP9vSdGYkIzJ
i09a14Oqj1Qv2PWFMTSjYolLHZCgZJ6LqQD/S0CY8eVmHeoYv2U6jHpZFIX7yQsP
ahlAiqgqneV6GE0=
=zU1K
-----END PGP SIGNATURE-----
Merge tag 'stm-for-greg-20170825' of git://git.kernel.org/pub/scm/linux/kernel/git/ash/stm into char-misc-next
Alexander writes:
stm class / intel_th: Updates for 4.14
Intel TH:
* Updated subdevice management code to better fit host mode
* Added support for Low Power Path (LPP) output type
* Fixed memory allocation with IOMMU enabled (DMAR tables)
* Added Cannon Lake PCH PCI IDs
* Added a quirk to force time sync on devices that need it
STM:
* Fixed potential read overflow in ioctl()
* Documented stm_ftrace source.
amba_id are not supposed to change at runtime. All functions
working with const amba_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
amba_id are not supposed to change at runtime. All functions
working with const amba_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
amba_id are not supposed to change at runtime. All functions
working with const amba_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
amba_id are not supposed to change at runtime. All functions
working with const amba_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
amba_id are not supposed to change at runtime. All functions
working with const amba_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
amba_id are not supposed to change at runtime. All functions
working with const amba_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
amba_id are not supposed to change at runtime. All functions
working with const amba_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
amba_id are not supposed to change at runtime. All functions
working with const amba_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
amba_id are not supposed to change at runtime. All functions
working with const amba_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The casting and other things here is odd, and causes sparse to
complain:
drivers/hwtracing/coresight/coresight-stm.c:279:35: warning: incorrect type in argument 1 (different address spaces)
drivers/hwtracing/coresight/coresight-stm.c:279:35: expected void [noderef] <asn:2>*addr
drivers/hwtracing/coresight/coresight-stm.c:279:35: got struct stm_drvdata *drvdata
drivers/hwtracing/coresight/coresight-stm.c:327:17: warning: incorrect type in argument 2 (different address spaces)
drivers/hwtracing/coresight/coresight-stm.c:327:17: expected void volatile [noderef] <asn:2>*addr
drivers/hwtracing/coresight/coresight-stm.c:327:17: got void *addr
drivers/hwtracing/coresight/coresight-stm.c:330:17: warning: incorrect type in argument 2 (different address spaces)
drivers/hwtracing/coresight/coresight-stm.c:330:17: expected void volatile [noderef] <asn:2>*addr
drivers/hwtracing/coresight/coresight-stm.c:330:17: got void *addr
drivers/hwtracing/coresight/coresight-stm.c:333:17: warning: incorrect type in argument 2 (different address spaces)
drivers/hwtracing/coresight/coresight-stm.c:333:17: expected void volatile [noderef] <asn:2>*addr
drivers/hwtracing/coresight/coresight-stm.c:333:17: got void *addr
>From what I can tell, we don't really need to treat ch_addr as
anything besides a pointer, and we can just do pointer math
instead of ORing in the bits of the offset and achieve the same
thing.
Also, we were passing a drvdata pointer to the
coresight_timeout() function, but we really wanted to pass the
address of the register base. Luckily the base is the first
member of the structure, so everything works out, but this is
quite unsafe if we ever change the structure layout. Clean this
all up so sparse stops complaining on this code.
Reported-by: Satyajit Desai <sadesai@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The coresight SoC 600 supports ETR save-restore which allows us
to restore a trace session by retaining the RRP/RWP/STS.Full values
when the TMC leaves the Disabled state. However, the TMC doesn't
have a scatter-gather unit in built.
Also, TMCs have different PIDs in different configurations (ETF,
ETB & ETR), unlike the previous generation.
While the DEVID exposes some of the features/changes in the TMC,
it doesn't explicitly advertises the new save-restore feature
as described above.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Coresight SoC 600 TMC ETR supports save-restore feature,
where the values of the RRP/RWP and STS.Full are retained
when it leaves the Disabled state. Hence, we must program the
RRP/RWP and STS.Full to a proper value. For now, set the RRP/RWP
to the base address of the buffer and clear the STS.Full register.
This can be later exploited for proper save-restore of ETR
trace contexts (e.g, perf).
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the ETR supports split cache encoding (i.e, separate bits for
read and write transfers) unlike the older version (where read
and write transfers use the same encoding in AXICTL[2-5]).
This feature is not advertised and has to be described by the
static mask associated with the device id.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch cleans up how we setup the AXICTL register on
TMC ETR. At the moment we don't set the CacheCtrl bits, which
drives the arcache and awcache bits on AXI bus specifying the
cacheablitiy. Set this to Write-back Read and Write-allocate.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TMC in Coresight SoC-600 advertises the AXI address width
in the device configuration register.
Bit 16 - AXIAW_VALID
0 - AXI Address Width not valid
1 - Valid AXI Address width in Bits[23-17]
Bits [23-17] - AXIAW. If AXIAW_VALID = b01 then
0x20 - 32bit AXI address bus
0x28 - 40bit AXI address bus
0x2c - 44bit AXI address bus
0x30 - 48bit AXI address bus
0x34 - 52bit AXI address bus
Use the address bits from the device configuration register, if
available. Otherwise, default to 40bit.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SG unit in the TMC has been removed in Coresight SoC-600.
This is however advertised by DEVID:Bit 24 = 0b1. On the
previous generation, the bit is RES0, hence we can rely on the
DEVID to detect the support.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Mike Leach <mike.leach@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With new version of TMC ETR, there are differing set of
features supported by the TMC. Add the capability of a
given TMC ETR for making safer decisions at runtime.
The device configuration register of the TMC (DEVID) lists
some of the capabilities. So, we can detect some of them at
probe. However, some of the features (or changes in behavior)
are not advertised and we have to depend on the PID to infer
the features. So we use a static description of the "unadvertised"
capabilities attached to the PID. Combining both, the static
and the dynamic capabilities, we maintain a bitmask of the
available features which can be later checked to take
appropriate actions.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Coresight SoC 600 defines a new configuration for TMC, Embedded Trace
Streamer (ETS), indicated by 0x3 in MODE:CONFIG_TYPE. This would break
the existing driver which will treat anything other than ETR/ETB as an
ETF. Fix the driver to check the configuration type properly and also
add a warning if we encounter an unsupported configuration (ETS).
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Coresight TMC splits 64bit registers into a pair of 32bit registers
(e.g DBA, RRP, RWP). Provide helpers to read/write to these registers.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the new helpers for exposing coresight component registers,
choosing the 64bit variants for appropriate registers.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for reading a lower and upper 32bits of a register
as a single 64bit register. Also add simplified macros for
direct register accesses.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Linux coresight drivers define the programmable ATB replicator as
Qualcomm replicator, while this is designed by ARM. This can cause
confusion to a user selecting the driver. Cleanup all references to
make it explicitly clear. This patch :
1) Replace the compatible string for the replicator :
qcom,coresight-replicator1x => arm,coresight-dynamic-replicator
2) Changes the Kconfig symbol (since this is not part of any defconfigs)
CORESIGHT_QCOM_REPLICATOR => CORESIGHT_DYNAMIC_REPLICATOR
3) Improves the help message in the Kconfig.
4) Changes the name of the driver and the file :
coresight-replicator-qcom => coresight-dynamic-replicator
Cc: Pratik Patel <pratikp@codeaurora.org>
Cc: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: devicetree@vger.kernel.org
Cc: Mark Rutland <mark.rutland@arm.com>
Acked-by: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds handling to program the return stack option into ETMv4 hardware if
specified in the perf command line.
If option is not supported by the hardware then it will be ignored.
This allows capture to move between core/ETM combinations that have the
hardware support to those that do not.
Signed-off-by: Mike Leach <mike.leach@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds handling to program the return stack option into PTM hardware if
specified in the perf command line.
If option is not supported by the hardware then it will be ignored.
This allows capture to move between core/ETM combinations that have the
hardware support to those that do not.
Signed-off-by: Mike Leach <mike.leach@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Return stack is a programmable option on some ETM and PTM hardware.
Adds the option flags to enable this from the perf event command line.
Signed-off-by: Mike Leach <mike.leach@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
attribute_groups are not supposed to change at runtime. All functions
working with attribute_groups provided by <linux/sysfs.h> work with const
attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
2573 288 296 3157 c55 coresight-etm-perf.o
File size After adding 'const':
text data bss dec hex filename
2613 224 296 3133 c3d coresight-etm-perf.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Register ETMSYNCFR holds the number of by that need to be generated before
periodic synchronisation packets are inserted in the trace stream. By
zeroing out the config structure, the current code effectively disable
periodic synchronization.
This patch simply initialise the recommended value for this register as
specified in the technical reference manual.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Function etb_disable_hw() is already taking care of unlocking and locking
the coresight access register and as such doesn't need to be placed
within the unlock/lock of function etb_update_buffer().
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a buffer overflow happens the synchronisation patckets usually
present at the beginning of the buffer are lost, a situation that
prevents the decoder from knowing the context of the traces being
decoded.
This patch adds a barrier packet to be used by sink IPs when a buffer
overflow condition is detected. These barrier packets are then used
by the decoding library as markers to force re-synchronisation.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Internal CoreSight components are rendering trace data in little-endian
format. As such there is no need to convert the data once more, hence
removing the extra step.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many conditions may cause synchronisation to be lost when updating
the perf ring buffer but the end result is still the same: synchronisation
is lost. As such there is no need to increment the lost count for each
condition, just once will suffice.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some devices (TH 2.x devices at the moment), the internal time counter
is initially not synchronized to the global crystal clock, so the time
stamps it produces will not be useful. In this case, the driver needs
to force the time counter resync.
This applies the workaround to relevant devices.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
A glue layer may want to install its own hooks into trace capture start
and stop paths to apply workarounds. This adds optional callbacks.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
This adds Intel(R) Trace Hub PCI ID for Cannon Lake PCH-LP.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: <stable@vger.kernel.org>
This adds Intel(R) Trace Hub PCI ID for Cannon Lake PCH-H.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: <stable@vger.kernel.org>
The Low Power Path (LPP) output port type, looks mostly like PTI to
the software, with a few additional bits in the control register.
This extends the PTI driver to support LPP ports as well.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Trace Hub 2.x adds Low Power Path (LPP) output port type, which provides
a low power mode trace path from sources to PTI or BSSB.
This adds an output subdevice for the LPP port.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Instead of allocating devices for every possible output subdevice,
allow the switch to allocate only the ones that it knows about.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
The switch (GTH) does not directly interact with SOURCE type devices and
may not even be present (in host mode). To reflect this and avoid
inconsistencies between target and host mode, make SOURCE devices
descendant directly from the root (i.e. PCI) device. Their symlinks
will no longer appear under the switch device, but they can still
be found under intel_th bus.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Output subdevices that rely on other output subdevices (or otherwise
don't directly talk to an output port on the switch) don't need to be
assigned an output port either.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
The "size" variable comes from the user so we need to verify that it's
large enough to hold an stp_policy_id struct.
Fixes: 7bd1d4093c ("stm class: Introduce an abstraction for System Trace Module devices")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Here is the "big" char/misc driver patchset for 4.13-rc1.
Lots of stuff in here, a large thunderbolt update, w1 driver header
reorg, the new mux driver subsystem, google firmware driver updates, and
a raft of other smaller things. Full details in the shortlog.
All of these have been in linux-next for a while with the only reported
issue being a merge problem with this tree and the jc-docs tree in the
w1 documentation area. The fix should be obvious for what to do when it
happens, if not, we can send a follow-up patch for it afterward.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWVpXKA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynLrQCdG9SxRjAbOd6pT9Fr2NAzpUG84YsAoLw+I3iO
EMi60UXWqAFJbtVMS9Aj
=yrSq
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc updates from Greg KH:
"Here is the "big" char/misc driver patchset for 4.13-rc1.
Lots of stuff in here, a large thunderbolt update, w1 driver header
reorg, the new mux driver subsystem, google firmware driver updates,
and a raft of other smaller things. Full details in the shortlog.
All of these have been in linux-next for a while with the only
reported issue being a merge problem with this tree and the jc-docs
tree in the w1 documentation area"
* tag 'char-misc-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (147 commits)
misc: apds990x: Use sysfs_match_string() helper
mei: drop unreachable code in mei_start
mei: validate the message header only in first fragment.
DocBook: w1: Update W1 file locations and names in DocBook
mux: adg792a: always require I2C support
nvmem: rockchip-efuse: add support for rk322x-efuse
nvmem: core: add locking to nvmem_find_cell
nvmem: core: Call put_device() in nvmem_unregister()
nvmem: core: fix leaks on registration errors
nvmem: correct Broadcom OTP controller driver writes
w1: Add subsystem kernel public interface
drivers/fsi: Add module license to core driver
drivers/fsi: Use asynchronous slave mode
drivers/fsi: Add hub master support
drivers/fsi: Add SCOM FSI client device driver
drivers/fsi/gpio: Add tracepoints for GPIO master
drivers/fsi: Add GPIO based FSI master
drivers/fsi: Document FSI master sysfs files in ABI
drivers/fsi: Add error handling for slave
drivers/fsi: Add tracepoints for low-level operations
...
Here is the big driver core update for 4.13-rc1.
The large majority of this is a lot of cleanup of old fields in the
driver core structures and their remaining usages in random drivers.
All of those fixes have been reviewed by the various subsystem
maintainers. There's also some small firmware updates in here, a new
kobject uevent api interface that makes userspace interaction easier,
and a few other minor things.
All of these have been in linux-next for a long while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWVpX4A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymobgCfd0d13IfpZoq1N41wc6z2Z0xD7cwAnRMeH1/p
kEeISGpHPYP9f8PBh9FO
=Hfqt
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the big driver core update for 4.13-rc1.
The large majority of this is a lot of cleanup of old fields in the
driver core structures and their remaining usages in random drivers.
All of those fixes have been reviewed by the various subsystem
maintainers. There's also some small firmware updates in here, a new
kobject uevent api interface that makes userspace interaction easier,
and a few other minor things.
All of these have been in linux-next for a long while with no reported
issues"
* tag 'driver-core-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (56 commits)
arm: mach-rpc: ecard: fix build error
zram: convert remaining CLASS_ATTR() to CLASS_ATTR_RO()
driver-core: remove struct bus_type.dev_attrs
powerpc: vio_cmo: use dev_groups and not dev_attrs for bus_type
powerpc: vio: use dev_groups and not dev_attrs for bus_type
USB: usbip: convert to use DRIVER_ATTR_RW
s390: drivers: convert to use DRIVER_ATTR_RO/WO
platform: thinkpad_acpi: convert to use DRIVER_ATTR_RO/RW
pcmcia: ds: convert to use DRIVER_ATTR_RO
wireless: ipw2x00: convert to use DRIVER_ATTR_RW
net: ehea: convert to use DRIVER_ATTR_RO
net: caif: convert to use DRIVER_ATTR_RO
TTY: hvc: convert to use DRIVER_ATTR_RW
PCI: pci-driver: convert to use DRIVER_ATTR_WO
IB: nes: convert to use DRIVER_ATTR_RW
HID: hid-core: convert to use DRIVER_ATTR_RO and drv_groups
arm: ecard: fix dev_groups patch typo
tty: serdev: use dev_groups and not dev_attrs for bus_type
sparc: vio: use dev_groups and not dev_attrs for bus_type
hid: intel-ish-hid: use dev_groups and not dev_attrs for bus_type
...
Coresight includes debug module and usually the module connects with CPU
debug logic. ARMv8 architecture reference manual (ARM DDI 0487A.k) has
description for related info in "Part H: External Debug".
Chapter H7 "The Sample-based Profiling Extension" introduces several
sampling registers, e.g. we can check program counter value with
combined CPU exception level, secure state, etc. So this is helpful for
analysis CPU lockup scenarios, e.g. if one CPU has run into infinite
loop with IRQ disabled. In this case the CPU cannot switch context and
handle any interrupt (including IPIs), as the result it cannot handle
SMP call for stack dump.
This patch is to enable coresight debug module, so firstly this driver
is to bind apb clock for debug module and this is to ensure the debug
module can be accessed from program or external debugger. And the driver
uses sample-based registers for debug purpose, e.g. when system triggers
panic, the driver will dump program counter and combined context
registers (EDCIDSR, EDVIDSR); by parsing context registers so can
quickly get to know CPU secure state, exception level, etc.
Some of the debug module registers are located in CPU power domain, so
this requires the CPU power domain stays on when access related debug
registers, but the power management for CPU power domain is quite
dependent on SoC integration for power management. For the platforms
which with sane power controller implementations, this driver follows
the method to set EDPRCR to try to pull the CPU out of low power state
and then set 'no power down request' bit so the CPU has no chance to
lose power.
If the SoC has not followed up this design well for power management
controller, the user should use the command line parameter or sysfs
to constrain all or partial idle states to ensure the CPU power
domain is enabled and access coresight CPU debug component safely.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is refactor to add function of_coresight_get_cpu(), so it's used to
retrieve CPU id for coresight component. Finally can use it as a common
function for multiple places.
Suggested-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The of_get_coresight_platform_data iterates over the possible CPU nodes
to find a given cpu phandle. However it does not drop the reference
to the node pointer returned by the of_get_coresight_platform_data.
This patch also introduces another minor fix is to use
of_cpu_device_node_get() to replace of_get_cpu_node().
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
[Leo: minor tweaks for of_get_coresight_platform_data]
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before making any DMA API calls, the ETR driver should really be setting
its masks to ensure that DMA is possible. Especially since it can
address more than the 32-bit default mask set by the AMBA bus code.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Delete a character in this description for a condition check.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Link: http://events.linuxfoundation.org/sites/events/files/slides/LCJ16-Refactor_Strings-WSang_0.pdf
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Almost low level functions from open firmware have used const to
qualify device_node structures, so add const for device_node
parameters in of_coresight related functions.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In current code the output logs are not well symmetric for sink and link
enabling and disabling. This patch is to fix that so can output paired
logs.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For software sources (i.e STM), there could be multiple agents
generating the trace data, unlike the ETMs. So we need to
properly do the accounting for the active number of users
to disable the device when the last user goes away. Right
now, the reference counting is broken for sources as we skip
the actions when we detect that the source is enabled.
This patch fixes the problem by adding the refcounting for
software sources, even when they are enabled.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Reported-by: Robert Walker <robert.walker@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With a coresight tracing session, the components along the path
from the source to sink are disabled after the source is disabled.
However, if the source was not actually disabled due to active
users, we should not disable the components in the path.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dev_attrs field has long been "depreciated" and is finally being
removed, and as this driver isn't even using it, just drop the NULL
setting, it is pointless.
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
etm_probe4() holds get_online_cpus() while invoking
cpuhp_setup_state_nocalls().
cpuhp_setup_state_nocalls() invokes get_online_cpus() as well. This is
correct, but prevents the conversion of the hotplug locking to a percpu
rwsem.
Use cpuhp_setup_state_nocalls_cpuslocked() to avoid the nested
call. Convert *_online_cpus() to the new interfaces while at it.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/20170524081547.983493849@linutronix.de
etm_probe() holds get_online_cpus() while invoking
cpuhp_setup_state_nocalls().
cpuhp_setup_state_nocalls() invokes get_online_cpus() as well. This is
correct, but prevents the conversion of the hotplug locking to a percpu
rwsem.
Use cpuhp_setup_state_nocalls_cpuslocked() to avoid the nested
call. Convert *_online_cpus() to the new interfaces while at it.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/20170524081547.889092478@linutronix.de
set_memory_* functions have moved to set_memory.h. Switch to this
explicitly.
Link: http://lkml.kernel.org/r/1488920133-27229-9-git-send-email-labbott@redhat.com
Signed-off-by: Laura Abbott <labbott@redhat.com>
Acked-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here is the big set of new char/misc driver drivers and features for
4.12-rc1.
There's lots of new drivers added this time around, new firmware drivers
from Google, more auxdisplay drivers, extcon drivers, fpga drivers, and
a bunch of other driver updates. Nothing major, except if you happen to
have the hardware for these drivers, and then you will be happy :)
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWQvAgg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yknsACgzkAeyz16Z97J3UTaeejbR7nKUCAAoKY4WEHY
8O9f9pr9gj8GMBwxeZQa
=OIfB
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big set of new char/misc driver drivers and features for
4.12-rc1.
There's lots of new drivers added this time around, new firmware
drivers from Google, more auxdisplay drivers, extcon drivers, fpga
drivers, and a bunch of other driver updates. Nothing major, except if
you happen to have the hardware for these drivers, and then you will
be happy :)
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (136 commits)
firmware: google memconsole: Fix return value check in platform_memconsole_init()
firmware: Google VPD: Fix return value check in vpd_platform_init()
goldfish_pipe: fix build warning about using too much stack.
goldfish_pipe: An implementation of more parallel pipe
fpga fr br: update supported version numbers
fpga: region: release FPGA region reference in error path
fpga altera-hps2fpga: disable/unprepare clock on error in alt_fpga_bridge_probe()
mei: drop the TODO from samples
firmware: Google VPD sysfs driver
firmware: Google VPD: import lib_vpd source files
misc: lkdtm: Add volatile to intentional NULL pointer reference
eeprom: idt_89hpesx: Add OF device ID table
misc: ds1682: Add OF device ID table
misc: tsl2550: Add OF device ID table
w1: Remove unneeded use of assert() and remove w1_log.h
w1: Use kernel common min() implementation
uio_mf624: Align memory regions to page size and set correct offsets
uio_mf624: Refactor memory info initialization
uio: Allow handling of non page-aligned memory regions
hangcheck-timer: Fix typo in comment
...
Corrected to get the port numbering to allow programmable replicator driver
to operate correctly.
By convention, CoreSight devices number ports, not endpoints in
the .dts files:-
port {
reg<N>
endpoint {
}
}
Existing code read endpoint number - always 0x0, rather than the correct
port number.
Signed-off-by: Mike Leach <mike.leach@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for adding more flags to perf AUX records, introduce a
separate API for setting the flags for a session, rather than appending
more bool arguments to perf_aux_output_end. This allows to set each
flag at the time a corresponding condition is detected, instead of
tracking it in each driver's private state.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: vince@deater.net
Link: http://lkml.kernel.org/r/20170220133352.17995-3-alexander.shishkin@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Output 'activation' may fail for the reasons of the output driver,
for example, if msc's buffer is not allocated. We forget, however,
to drop the module reference in this case. So each attempt at
activation in this case leaks a reference, preventing the module
from ever unloading.
This patch adds the missing module_put() in the activation error
path.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: stable@vger.kernel.org # v4.8+
->fault(), ->page_mkwrite(), and ->pfn_mkwrite() calls do not need to
take a vma and vmf parameter when the vma already resides in vmf.
Remove the vma parameter to simplify things.
[arnd@arndb.de: fix ARM build]
Link: http://lkml.kernel.org/r/20170125223558.1451224-1-arnd@arndb.de
Link: http://lkml.kernel.org/r/148521301778.19116.10840599906674778980.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Darrick J. Wong <darrick.wong@oracle.com>
Cc: Matthew Wilcox <mawilcox@microsoft.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Jan Kara <jack@suse.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When using the ETM4x tracers from the perf interface two trace options are
available: cycle accurate and timestamp.
Enabling the timestamp feature is done by setting TRCCONFIGR.TS (bit 11).
The position of the timestamp bit in that register coincidentally happens
to be the same as what was chosen to enable timestamping from the 'mode'
sysFS entry. The code does the right thing but the semantic is wrong.
This patch sets TRCCONFIGR.TS explicitly, as it is done from the sysFS
interface. That way timestamps are set the same way from both perf and
sysFS and there is no misunderstanding as to what is intended.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using perf record 'cyclacc' option in cs_etm event was not setting up cycle
accurate trace correctly.
Corrects bit set in TRCCONFIGR to enable cycle accurate trace.
Programs TRCCCCTLR with a valid threshold value as required by ETMv4 spec.
Signed-off-by: Mike Leach <mike.leach@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The stm is automatically enabled when an application sets the policy
via ->link() call back by using coresight_enable(), which keeps the
refcount of the current users of the STM. However, the unlink() callback
issues stm_disable() directly, which leaves the STM turned off, without
the coresight layer knowing about it. This prevents any further uses
of the STM hardware as the coresight layer still thinks the STM is
turned on and doesn't enable the hardware when required. Even manually
enabling the STM via sysfs can't really enable the hw.
e.g,
$ echo 1 > $CS_DEVS/$ETR/enable_sink
$ mkdir -p $CONFIG_FS/stp-policy/$source.0/stm_test/
$ echo 32768 65535 > $CONFIG_FS/stp-policy/$source.0/stm_test/channels
$ echo 64 > $CS_DEVS/$source/traceid
$ ./stm_app
Sending 64000 byte blocks of pattern 0 at 0us intervals
Success to map channel(32768~32783) to 0xffffa95fa000
Sending on channel 32768
$ dd if=/dev/$ETR of=~/trace.bin.1
597+1 records in
597+1 records out
305920 bytes (306 kB) copied, 0.399952 s, 765 kB/s
$ ./stm_app
Sending 64000 byte blocks of pattern 0 at 0us intervals
Success to map channel(32768~32783) to 0xffff7e9e2000
Sending on channel 32768
$ dd if=/dev/$ETR of=~/trace.bin.2
0+0 records in
0+0 records out
0 bytes (0 B) copied, 0.0232083 s, 0.0 kB/s
Note that we don't get any data from the ETR for the second session.
Also dmesg shows :
[ 77.520458] coresight-tmc 20800000.etr: TMC-ETR enabled
[ 77.537097] coresight-replicator etr_replicator@20890000: REPLICATOR enabled
[ 77.558828] coresight-replicator main_replicator@208a0000: REPLICATOR enabled
[ 77.581068] coresight-funnel 208c0000.main_funnel: FUNNEL inport 0 enabled
[ 77.602217] coresight-tmc 20840000.etf: TMC-ETF enabled
[ 77.618422] coresight-stm 20860000.stm: STM tracing enabled
[ 139.554252] coresight-stm 20860000.stm: STM tracing disabled
# End of first tracing session
[ 146.351135] coresight-tmc 20800000.etr: TMC read start
[ 146.514486] coresight-tmc 20800000.etr: TMC read end
# Note that the STM is not turned on via stm_generic_link()->coresight_enable()
# and hence none of the components are turned on.
[ 152.479080] coresight-tmc 20800000.etr: TMC read start
[ 152.542632] coresight-tmc 20800000.etr: TMC read end
This patch fixes the problem by balancing the unlink operation by using
the coresight_disable(), keeping the coresight layer in sync with the
hardware state and thus allowing normal usage of the STM component.
Fixes: commit 237483aa5c ("coresight: stm: adding driver for CoreSight STM component")
Cc: Pratik Patel <pratikp@codeaurora.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable@vger.kernel.org # 4.7+
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Reported-by: Robert Walker <robert.walker@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Even if both drivers are compiled in only one instance can run on a given
system depending on the available tracer cell.
So having seperate hotplug states for them is pointless.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: http://lkml.kernel.org/r/20161221192112.162765484@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When the state names got added a script was used to add the extra argument
to the calls. The script basically converted the state constant to a
string, but the cleanup to convert these strings into meaningful ones did
not happen.
Replace all the useless strings with 'subsys/xxx/yyy:state' strings which
are used in all the other places already.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Link: http://lkml.kernel.org/r/20161221192112.085444152@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
o STM can hook into the function tracer
o Function filtering now supports more advance glob matching
o Ftrace selftests updates and added tests
o Softirq tag in traces now show only softirqs
o ARM nop added to non traced locations at compile time
o New trace_marker_raw file that allows for binary input
o Optimizations to the ring buffer
o Removal of kmap in trace_marker
o Wakeup and irqsoff tracers now adhere to the set_graph_notrace file
o Other various fixes and clean ups
Note, there are two patches marked for stable. These were discovered
near the end of the 4.9 rc release cycle. By the time I had them tested
it was just a matter of days before 4.9 would be released, and I
figured I would just submit them in the merge window. They are old
bugs and not critical. Nothing non-root could abuse.
-----BEGIN PGP SIGNATURE-----
iQExBAABCAAbBQJYUrFHFBxyb3N0ZWR0QGdvb2RtaXMub3JnAAoJEMm5BfJq2Y3L
2+AIAIr20kSQV/nA5htGAeCTobVk3WUxY6bvjd9mIJDKPP19akNLyREW0G3KnfCr
yhx4aFRZG98fRu/6F8qieRosyN36lADDVYHelMFHMpcTOpE2aZGjaaOuNGxOEA9v
FmMPTX+K3+dzKyFP4l68R3+5JuQ1/AqLTioTWeLW8IDQ2OOVsjD8+0BuXrNKMJDY
o6U4Hk5U/vn+zHc6BmgBzloAXemBd7iJ1t5V3FRRGvm8yv3HU85Twc5ofGeYTWvB
J8PboEywRlIzxg0Kd8mxnMI5PgaKZSEc2ub8E7cY/CZ5PYpDE2xDA2hJmJgfYp00
1VW+DHRpRZfElsCcya6S6P4bs5Y=
=MGZ/
-----END PGP SIGNATURE-----
Merge tag 'trace-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
"This release has a few updates:
- STM can hook into the function tracer
- Function filtering now supports more advance glob matching
- Ftrace selftests updates and added tests
- Softirq tag in traces now show only softirqs
- ARM nop added to non traced locations at compile time
- New trace_marker_raw file that allows for binary input
- Optimizations to the ring buffer
- Removal of kmap in trace_marker
- Wakeup and irqsoff tracers now adhere to the set_graph_notrace file
- Other various fixes and clean ups"
* tag 'trace-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (42 commits)
selftests: ftrace: Shift down default message verbosity
kprobes/trace: Fix kprobe selftest for newer gcc
tracing/kprobes: Add a helper method to return number of probe hits
tracing/rb: Init the CPU mask on allocation
tracing: Use SOFTIRQ_OFFSET for softirq dectection for more accurate results
tracing/fgraph: Have wakeup and irqsoff tracers ignore graph functions too
fgraph: Handle a case where a tracer ignores set_graph_notrace
tracing: Replace kmap with copy_from_user() in trace_marker writing
ftrace/x86_32: Set ftrace_stub to weak to prevent gcc from using short jumps to it
tracing: Allow benchmark to be enabled at early_initcall()
tracing: Have system enable return error if one of the events fail
tracing: Do not start benchmark on boot up
tracing: Have the reg function allow to fail
ring-buffer: Force rb_end_commit() and rb_set_commit_to_write() inline
ring-buffer: Froce rb_update_write_stamp() to be inlined
ring-buffer: Force inline of hotpath helper functions
tracing: Make __buffer_unlock_commit() always_inline
tracing: Make tracepoint_printk a static_key
ring-buffer: Always inline rb_event_data()
ring-buffer: Make rb_reserve_next_event() always inlined
...
Most error branches following the call to alloc_event_data contain a call
to etm_free_aux. This patch add a call to etm_free_aux to an error branch
that does not call it.
This issue was found with Hector.
Signed-off-by: Quentin Lambert <lambert.quentin@gmail.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tmc_etr_enable_hw() fills the buffer with 0's before enabling
the hardware. So, we don't need an explicit memset() in
tmc_enable_etr_sink_sysfs() before calling the tmc_etr_enable_hw().
This patch removes the explicit memset from tmc_enable_etr_sink_sysfs.
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Get rid of the superfluous mode parameter and the check for
the mode in tmc_etX_enable_sink_{perf/sysfs}. While at it, also
remove the unnecessary WARN_ON() checks.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mode of operation of the TMC tracked in drvdata->mode is defined
as a local_t type. This is always checked and modified under the
drvdata->spinlock and hence we don't need local_t for it and the
unnecessary synchronisation instructions that comes with it. This
change makes the code a bit more cleaner.
Also fixes the order in which we update the drvdata->mode to
CS_MODE_DISABLED. i.e, in tmc_disable_etX_sink we change the
mode to CS_MODE_DISABLED before invoking tmc_disable_etX_hw()
which in turn depends on the mode to decide whether to dump the
trace to a buffer.
Applies on mathieu's coresight/next tree [1]
https://git.linaro.org/kernel/coresight.git next
Reported-by: Venkatesh Vivekanandan <venkatesh.vivekanandan@broadcom.com>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using coresight from the perf interface sinks are specified
as part of the perf command line. As such the sink needs to be
disabled once it has been acknowledged by the coresight framework.
Otherwise the sink stays enabled, which may interfere with other
sessions.
This patch removes the sink selection check from the build path
process and make it a function on it's own. The function is
then used when operating from sysFS or perf to determine what
sink has been selected.
If operated from perf the status of the "enable_sink" flag is
reset so that concurrent session can use a different sink. When
used from sysFS the status of the flag is left untouched since
users have full control.
The implementation doesn't handle a scenario where a sink has
been enabled from sysFS and another sink is selected from the
perf command line as both modes of operation are mutually
exclusive.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the current driver for Coresight components, two features of PTM
components are missing:
1. Branch Broadcasting (present also in ETM but called Branch Output)
2. Return Stack (only present in PTM v1.0 and PTMv1.1)
These features can be added simply to the code using `mode` field of
`etm_config` struct.
1. **Branch Broadcast** : The branch broadcast feature is present in ETM
components as well and is called Branch output. It allows to retrieve
addresses for direct branch addresses alongside the indirect branch
addresses. For example, it could be useful in cases when tracing without
source code.
2. **Return Stack** : The return stack option allows to retrieve the
return addresses of function calls. It can be useful to avoid CRA
(Code Reuse Attacks) by keeping a shadowstack.
Signed-off-by: Muhammad Abdul Wahab <muhammadabdul.wahab@centralesupelec.fr>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An extra space is removed.
Signed-off-by: Muhammad Abdul Wahab <muhammadabdul.wahab@centralesupelec.fr>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In STM framework driver, the trace data writing loop would keep running
until it received a negative return value or the whole trace packet has
been written to STM device. So if the .packet() of STM device always
returns zero since the device is not enabled or the parameter isn't
supported, STM framework driver will stall into a dead loop.
Returning -EACCES (Permission denied) in .packet() if the device is
disabled makes more sense, and this is the same for returning -EINVAL
if the channel passed into is not supported.
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If CONFIG_STM_SOURCE_FTRACE is selected, Function trace data can be
writen to sink via STM, all functions that related to writing data
packets to STM should be marked 'notrace' to avoid being traced by
Ftrace, otherwise the program would stall into an endless loop.
Link: http://lkml.kernel.org/r/1479715043-6534-7-git-send-email-zhang.chunyan@linaro.org
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Acked-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
If CONFIG_STM_SOURCE_FTRACE is selected, Function trace data can be
writen to sink via STM, all functions that related to writing data
packets to STM should be marked 'notrace' to avoid being traced by
Ftrace, otherwise the program would stall into an endless loop.
Link: http://lkml.kernel.org/r/1479715043-6534-6-git-send-email-zhang.chunyan@linaro.org
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Acked-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
If CONFIG_STM_SOURCE_FTRACE is selected, Function trace data can be
writen to sink via STM, all functions that related to writing data
packets to STM should be marked 'notrace' to avoid being traced by
Ftrace, otherwise the program would stall into an endless loop.
Link: http://lkml.kernel.org/r/1479715043-6534-5-git-send-email-zhang.chunyan@linaro.org
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Acked-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
If CONFIG_STM_SOURCE_FTRACE is selected, Function trace data can be
writen to sink via STM, all functions that related to writing data
packets to STM should be marked 'notrace' to avoid being traced by
Ftrace, otherwise the program would stall into an endless loop.
Link: http://lkml.kernel.org/r/1479715043-6534-4-git-send-email-zhang.chunyan@linaro.org
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Acked-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
This patch adds a driver that models itself as an stm_source called
stm_ftrace. Once the stm device and stm_ftrace have been linked via
sysfs, the driver registers itself as a trace_export and everything
passed to the interface from Ftrace subsystem will end up in the STM
trace engine.
Link: http://lkml.kernel.org/r/1479715043-6534-3-git-send-email-zhang.chunyan@linaro.org
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Acked-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
When detecting host debugger mode either though a module option or via
the scratchpad register, do not export any configuration or capture
related attributes to userspace and refuse attempts by the output drivers
to configure output ports.
This way, GTH can still act as a hub and ensure that the other components
that rely on its presence continue to function properly, namely the
source devices.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
This patch adds a 'host_mode' module option to enable host-driven
operational mode in the driver. In this mode, the driver does not
perform trace configuration or enable trace capture, but still
provides all the means necessary for software trace sources to
write their data to the Trace Hub. This means that the debug host
takes care of all the configuration and enabling and we do not
interfere.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Suzuki K Poulose