Right now callers have to check whether scsi_host->bqt is already
set up, it's much cleaner to just have scsi_init_shared_tag_map()
does this check on its own.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The segment->done functions return a iscsi error value which gives
a lot more info than conn failed, so this patch has us return
that value. I also add a new one for xmit failures.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
I had this in my patchset to add target reset support, but
it got dropped due to patching conflicts. This initial patch
just renames the function and users. We are actually just
dropping the session, and so this does not have anything to do
with the host exactly. It does for software iscsi because
we allocate a host per session, but for cxgb3i this makes no
sense.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Some endpoint code was using unsigned int and some
was using uint64_t. This converts it all to uint64_t.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
If the driver knows when hardware is removed like with cxgb3i,
bnx2i, qla4xxx and iser then we will want to remove the sessions/devices
that are bound to that device before removing the host.
cxgb3i and in the future bnx2i will remove the host and that will
remove all the sessions on the hba. iser can call iscsi_kill_session
when it gets an event that indicates that a hca is removed.
And when qla4xxx is hooked in to the lib (it is only hooked into
the class right now) it can call iscsi remove host like the
partial offload card drivers.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
If the target is blocked and fast io fail tmo has not fired
then we requeue with DID_TRANSPORT_DISRUPTED. Once that
tmo fires we fail with DID_TRANSPORT_FAILFAST.
v2
- seperate from
"fc class: unblock target after calling terminate callback"
to make it easier to review.
- Add JamesS's ack from list.
v2
- initial patch
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Currently, if there is a transport problem the iscsi drivers will return
outstanding commands (commands being exeucted by the driver/fw/hw) with
DID_BUS_BUSY and block the session so no new commands can be queued.
Commands that are caught between the failure handling and blocking are
failed with DID_IMM_RETRY or one of the scsi ml queuecommand return values.
When the recovery_timeout fires, the iscsi drivers then fail IO with
DID_NO_CONNECT.
For fcp, some drivers will fail some outstanding IO (disk but possibly not
tape) with DID_BUS_BUSY or DID_ERROR or some other value that causes a retry
and hits the scsi_error.c failfast check, block the rport, and commands
caught in the race are failed with DID_IMM_RETRY. Other drivers, may
hold onto all IO and wait for the terminate_rport_io or dev_loss_tmo_callbk
to be called.
The following patches attempt to unify what upper layers will see drivers
like multipath can make a good guess. This relies on drivers being
hooked into their transport class.
This first patch just defines two new host byte errors so drivers can
return the same value for when a rport/session is blocked and for
when the fast_io_fail_tmo fires.
The idea is that if the LLD/class detects a problem and is going to block
a rport/session, then if the LLD wants or must return the command to scsi-ml,
then it can return it with DID_TRANSPORT_DISRUPTED. This will requeue
the IO into the same scsi queue it came from, until the fast io fail timer
fires and the class decides what to do.
When using multipath and the fast_io_fail_tmo fires then the class
can fail commands with DID_TRANSPORT_FAILFAST or drivers can use
DID_TRANSPORT_FAILFAST in their terminate_rport_io callbacks or
the equivlent in iscsi if we ever implement more advanced recovery methods.
A LLD, like lpfc, could continue to return DID_ERROR and then it will hit
the normal failfast path, so drivers do not have fully be ported to
work better. The point of the patches is that upper layers will
not see a failure that could be recovered from while the rport/session is
blocked until fast_io_fail_tmo/recovery_timeout fires.
V3
Remove some comments.
V2
Fixed patch/diff errors and renamed DID_TRANSPORT_BLOCKED to
DID_TRANSPORT_DISRUPTED.
V1
initial patch.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
When we block a rport and the driver implements the terminate
callback we will fail IO that was running quickly. However
IO that was in the scsi_device/block queue sits there until
the dev_loss_tmo fires, and this can make it look like IO is
lost because new IO will get executed but that IO stuck in
the blocked queue sits there for some time longer.
With this patch when the fast io fail tmo fires, we will
fail the blocked IO and any new IO. This patch also allows
all drivers to partially support the fast io fail tmo. If the
terminate io callback is not implemented, we will still fail blocked
IO and any new IO, so multipath can handle that.
This patch also allows the fc and iscsi classes to implement the
same behavior. The timers are just unfornately named differently.
This patch also fixes the problem where drivers were unblocking
the target in their terminate callback, which was needed for
rport removal, but for fast io fail timeout it would cause
IO to bounce arround the scsi/block layer and the LLD queuecommand.
And it for drivers that could have IO stuck but did not have
a terminate callback the unblock calls in the class will fix
them.
v2.
- fix up bit setting style to meet JamesS's pref.
- Broke out new host byte error changes to make it easier to read.
- added JamesS's ack from list.
v1
- initial patch
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
SCSI-ml manages the queueing limits for the device and host, but
does not do so at the target level. However something something similar
can come in userful when a driver is transitioning a transport object to
the the blocked state, becuase at that time we do not want to queue
io and we do not want the queuecommand to be called again.
The patch adds code similar to the exisiting SCSI_ML_*BUSY handlers.
You can now return SCSI_MLQUEUE_TARGET_BUSY when we hit
a transport level queueing issue like the hw cannot allocate some
resource at the iscsi session/connection level, or the target has temporarily
closed or shrunk the queueing window, or if we are transitioning
to the blocked state.
bnx2i, when they rework their firmware according to netdev
developers requests, will also need to be able to limit queueing at this
level. bnx2i will hook into libiscsi, but will allocate a scsi host per
netdevice/hba, so unlike pure software iscsi/iser which is allocating
a host per session, it cannot set the scsi_host->can_queue and return
SCSI_MLQUEUE_HOST_BUSY to reflect queueing limits on the transport.
The iscsi class/driver can also set a scsi_target->can_queue value which
reflects the max commands the driver/class can support. For iscsi this
reflects the number of commands we can support for each session due to
session/connection hw limits, driver limits, and to also reflect the
session/targets's queueing window.
Changes:
v1 - initial patch.
v2 - Fix scsi_run_queue handling of multiple blocked targets.
Previously we would break from the main loop if a device was added back on
the starved list. We now run over the list and check if any target is
blocked.
v3 - Rediff for scsi-misc.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (37 commits)
[SCSI] zfcp: fix double dbf id usage
[SCSI] zfcp: wait on SCSI work to be finished before proceeding with init dev
[SCSI] zfcp: fix erp list usage without using locks
[SCSI] zfcp: prevent fc_remote_port_delete calls for unregistered rport
[SCSI] zfcp: fix deadlock caused by shared work queue tasks
[SCSI] zfcp: put threshold data in hba trace
[SCSI] zfcp: Simplify zfcp data structures
[SCSI] zfcp: Simplify get_adapter_by_busid
[SCSI] zfcp: remove all typedefs and replace them with standards
[SCSI] zfcp: attach and release SAN nameserver port on demand
[SCSI] zfcp: remove unused references, declarations and flags
[SCSI] zfcp: Update message with input from review
[SCSI] zfcp: add queue_full sysfs attribute
[SCSI] scsi_dh: suppress comparison warning
[SCSI] scsi_dh: add Dell product information into rdac device handler
[SCSI] qla2xxx: remove the unused SCSI_QLOGIC_FC_FIRMWARE option
[SCSI] qla2xxx: fix printk format warnings
[SCSI] qla2xxx: Update version number to 8.02.01-k8.
[SCSI] qla2xxx: Ignore payload reserved-bits during RSCN processing.
[SCSI] qla2xxx: Additional residual-count corrections during UNDERRUN handling.
...
Right now SCSI and others do their own command timeout handling.
Move those bits to the block layer.
Instead of having a timer per command, we try to be a bit more clever
and simply have one per-queue. This avoids the overhead of having to
tear down and setup a timer for each command, so it will result in a lot
less timer fiddling.
Signed-off-by: Mike Anderson <andmike@linux.vnet.ibm.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
There's already a fc_vport_termintate() call exported by
the transport. This patch adds a symmetric call to the API to allow
an NPIV-capable LLD to instantiate vports sans user intervention.
Additional comments/updates:
Re: scsi_fc_transport.txt
Add a function prototype for fc_vport_terminate similar to what's
done for fc_vport_create
Re: fc_vport_create
I recommend we pass the channel number in fc_vport_create rather
than fixing it at zero.
Also, ids->vport_type should be set to FC_PORTTYPE_NPIV prior to
calling fc_vport_create. The comment is also meaningless.
Added-by and
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Brian King <brking@linux.vnet.ibm.com> reported that fibre channel
devices can oops during scanning if their ports block (because the
device goes from CREATED -> BLOCK -> RUNNING rather than CREATED ->
BLOCK -> CREATED).
Fix this by adding a new state: CREATED_BLOCK which can only transition
back to CREATED and disallow the CREATED -> BLOCK transition. Now both
the created and blocked states that the mid-layer recognises can include
CREATED_BLOCK.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The created and blocked states are very shortly going to correspond to
mixed sdev_state states.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch adds scsi netlink recieve and event support for transport
and scsi LLDD's. It is a reimplementation of the patch posted last
week by David Somayajulu.
http://marc.info/?l=linux-scsi&m=121745486221819&w=2
There are a few things done differently:
- Transport support is included
- Event delivery is included
- The vendor message is now its own unique message type, considered
part of the generic "SCSI Transport".
- LLDD entry points are now registered rather than included in the
scsi_host_template.
Background: When I started to implement the event handler via template,
I had to either: muck up scsi_add_host and scsi_remove_host; or have
the event handler search all possible shosts. Neither was acceptable.
Moving to a registration solves this, and also limits the scope of
the changes to something that could be backported to a distro without
breaking an already-released-distro kabi. However, I admit it isn't
as elegant, as the passing of the LLDD host template in the
registration and the complexity around dynamic add/remove shows.
- The receive path was augmented to require a unique identifier for
the LLDD before the message was allowed to be handed off to the
driver. Given how quickly very fatal errors occur if there's msg
mismatches (which I saw in testing my own tools :), I believe this
to be a very good thing. The id plays off the vendor id scheme already
introduced for the vendor unique event messages used by FC.
Additionally, the id use as the basis of the registration/deregistration.
- Send assist functions, for both the transport and LLDDs are included.
[fujita.tomonori@lab.ntt.co.jp: fix missing cast]
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
For IBM z series certain LUNs can no longer be accessed.
This is because kernel version 2.6.19 a check was introduced not to
create a generic SCSI device for devices that return PQ=1 and
PDT=0x1f. For WLUNs (see SAM-3, p. 41ff) generic SCSI devices should
be created unconditionally without looking at the PQ bit, so add a
check for WLUNs in with this test.
Acked-by: Martin Petermann <martin@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Some USB devices set the protect bit in the INQUIRY data which
currently causes the DIF code in sd to assume (incorrectly) that they
support READ_CAPACITY(16). Fix this (only for the time being) by
making sure we only believe the protect bit in the inquiry data if the
device claims conformance to SCSI-3 or above.
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This re-introduces commit 2b14290078,
which was reverted due to the regression it caused by commit
fca082c9f1.
That regression was not root-caused by the original commit, it was just
uncovered by it, and the real fix was done by Alan Stern in commit
580da34847 ("Fix USB storage hang on
command abort").
We can thus re-introduce the change that was confirmed by Alan Jenkins
to be still required by his odd card reader.
Cc: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit 2b14290078, since it
seems to break some other USB storage devices (at least a JMicron USB to
ATA bridge). As such, while it apparently fixes some cardreaders, it
would need to be made conditional on the exact reader it fixes in order
to avoid causing regressions.
Cc: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The last_sector_bug flag was added to work around a bug in certain usb
cardreaders, where they would crash if a multiple sector read included the
last sector. The original implementation avoids this by e.g. splitting an 8
sector read which includes the last sector into a 7 sector read, and a single
sector read for the last sector. The flag is enabled for all USB devices.
This revealed a second bug in other usb cardreaders, which crash when they
get a multiple sector read which stops 1 sector short of the last sector.
Affected hardware includes the Kingston "MobileLite" external USB cardreader
and the internal USB cardreader on the Asus EeePC.
Extend the last_sector_bug workaround to ensure that any access which touches
the last 8 hardware sectors of the device is a single sector long. Requests
are shrunk as necessary to meet this constraint.
This gives us a safety margin against potential unknown or future bugs
affecting multi-sector access to the end of the device. The two known bugs
only affect the last 2 sectors. However, they suggest that these devices
are prone to fencepost errors and that multi-sector access to the end of the
device is not well tested. Popular OS's use multi-sector accesses, but they
rarely read the last few sectors. Linux (with udev & vol_id) automatically
reads sectors from the end of the device on insertion. It is assumed that
single sector accesses are more thoroughly tested during development.
Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Tested-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch (as1116) fixes a bug in scsi_eh_prep_cmnd() and
scsi_eh_restore_cmnd(). These routines are supposed to save any
values they change and restore them later, but someone forgot to
save & restore scmd->underflow.
This fixes part of the problem reported in Bugzilla #9638.
[jejb: fix up rejections around DIF/DIX]
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Implement support for DMA of protection information for devices that
are data integrity capable.
- Add support for mapping an extra scatter-gather list containing
the protection information.
- Allocate protection scsi_data_buffer if host is DIX (integrity DMA)
capable.
- Accessor function for checking whether a device has protection
enabled.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Controllers that support DMA of protection information must be told
explicitly how to handle the I/O. The controller has no knowledge of
the protection capabilities of the target device so this information
must be passed in the scsi_cmnd.
- The protection operation tells the HBA whether to generate, strip or
verify protection information.
- The protection type tells the HBA which layout the target is
formatted with. This is necessary because the controller must be
able to correctly interpret the included protection information in
order to verify it.
- When a scsi_cmnd is reused for error handling the protection
operation must be cleared and saved while error handling is in
progress.
- prot_op and prot_type are placed in an existing hole in scsi_cmnd
and don't cause the structure to grow.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Controllers that support protection information must indicate this to
the SCSI midlayer so that the ULD can prepare scsi_cmnds accordingly.
This patch implements a host mask and various types of protection:
- DIF Type 1-3 (between HBA and disk)
- DIX Type 0-3 (between OS and HBA)
The patch also allows the HBA to set the guard type to something
different than the T10-mandated CRC.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
multipath keeps a separate device table which may be
more current than the built-in one.
So we should make sure to always call ->attach whenever
a multipath map with hardware handler is instantiated.
And we should call ->detach on removal, too.
[sekharan: update as per comments from agk]
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch converts the EMC device handler to use a proper
state machine. We now also parse the extended INQUIRY
information to determine if long trespass commands are
supported. And we're now using the long trespass command
correctly. And finally there's now an check at init time
to refuse to attach to devices not supporting EMC-specific
VPD pages.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Instead of having each and every driver implement its own
device table scanning code we should rather implement a common
routine and scan the device tables there.
This allows us also to implement a general notifier chain
callback for all device handler instead for one per handler.
[sekharan: Fix rejections caused by conflicting bug fix]
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Daniel Debonzi reports that he has managed to wrap host_no. Increasing
the number of host numbers available to 32-bit from 16-bit allows the
problem to be evaded for another hundred years.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Kobjects do not have a limit in name size since a while, so stop
pretending that they do.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (102 commits)
[SCSI] scsi_dh: fix kconfig related build errors
[SCSI] sym53c8xx: Fix bogus sym_que_entry re-implementation of container_of
[SCSI] scsi_cmnd.h: remove double inclusion of linux/blkdev.h
[SCSI] make struct scsi_{host,target}_type static
[SCSI] fix locking in host use of blk_plug_device()
[SCSI] zfcp: Cleanup external header file
[SCSI] zfcp: Cleanup code in zfcp_erp.c
[SCSI] zfcp: zfcp_fsf cleanup.
[SCSI] zfcp: consolidate sysfs things into one file.
[SCSI] zfcp: Cleanup of code in zfcp_aux.c
[SCSI] zfcp: Cleanup of code in zfcp_scsi.c
[SCSI] zfcp: Move status accessors from zfcp to SCSI include file.
[SCSI] zfcp: Small QDIO cleanups
[SCSI] zfcp: Adapter reopen for large number of unsolicited status
[SCSI] zfcp: Fix error checking for ELS ADISC requests
[SCSI] zfcp: wait until adapter is finished with ERP during auto-port
[SCSI] ibmvfc: IBM Power Virtual Fibre Channel Adapter Client Driver
[SCSI] sg: Add target reset support
[SCSI] lib: Add support for the T10 (SCSI) Data Integrity Field CRC
[SCSI] sd: Move scsi_disk() accessor function to sd.h
...
Do not automatically "select" SCSI_DH for dm-multipath. If SCSI_DH
doesn't exist,just do not allow hardware handlers to be used.
Handle SCSI_DH being a module also. Make sure it doesn't allow DM_MULTIPATH
to be compiled in when SCSI_DH is a module.
[jejb: added comment for Kconfig syntax]
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Adds a new scsi_device flag, start_stop_pwr_cond: If enabled, the sd
driver will not send plain START STOP UNIT commands but ones with the
power condition field set to 3 (standby) or 1 (active) respectively.
Some FireWire disk firmwares do not stop the motor if power condition is
zero. Or worse, they become unresponsive after a START STOP UNIT with
power condition = 0 and start = 0.
http://lkml.org/lkml/2008/4/29/704
This patch only adds the necessary code to sd_mod but doesn't activate
it. Follow-up patches to the FireWire drivers will add detection of
affected devices and enable the code for them.
I did not add power condition values to scsi_error.c::scsi_eh_try_stu()
for now. The three firmwares which suffer from above mentioned problems
do not need START STOP UNIT in the error handler, and they are not
adversely affected by START STOP UNIT with power condition = 0 and start
= 1 (like scsi_eh_try_stu() sends it if scsi_device.allow_restart is
enabled).
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Tested-by: Tino Keitel <tino.keitel@gmx.de>
Move the accessor functions for the scsi_cmnd status from zfcp to the
SCSI include file. Change the interface to the functions to pass the
scsi_cmnd pointer instead of the status pointer.
Signed-off-by: Martin Petermann <martin@linux.vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Adds support for target reset to SG_SCSI_RESET.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Christoph objected to having sd.h in include/scsi since it is internal
to the sd driver. Move it to drivers/scsi/sd.h.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Let through upto the largest command of 260 defined by the scsi standard.
iscsi core supports this already. Now that the scsi-ml supports it we can
start using large commands.
[jejb:rejections fixed up]
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Acked-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The recv lock was defined so the iscsi layer could block
the recv path from processing IO during recovery. It
turns out iser just set a lock to that pointer which was pointless.
We now disconnect the transport connection before doing recovery
so we do not need the recv lock. For iscsi_tcp we still stop
the recv path incase older tools are being used.
This patch also has iscsi_itt_to_ctask user grab the session lock
and has the caller access the task with the lock or get a ref
to it in case the target is broken and sends a tmf success response
then sends data or a response for the command that was supposed to
be affected bty the tmf.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Drivers expect that the cmds_max value they pass to the iscsi layer
is the max scsi commands + mgmt tasks. This patch implements that
and fixes some checks for nr cmd limits.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This adds two new attrs used for creating initiator ports and
binding sessions to hardware.
The session level initiatorname:
Since bnx2i does a scsi_host per host device, we need to add the
iface initiator port settings on the session, so we can create
multiple initiator ports (each with different inames) per device/scsi_host.
The current iname reflects that qla4xxx can have one iname per hba, and we are
allocating a host per session for software. The iname on the host will
remain so we can export and set the hba level qla4xxx setting.
The ifacename attr:
To bind a session to a some peice of hardware in userspace we maintain
some mappings, but during boot or iscsid restart (iscsid contains the user
space part of the driver) we need to be able to figure out which of those
host mappings abstractions maps to certain sessions. This patch adds
a ifacename attr, which userspace can set to id the host side of the
endpoint across pivot_roots and iscsid restarts.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Add sysfs representation for the endpoint, so userspace can match the
host and session to the endpoint. This will allow us to set the host's
parent correctly at host creation time.
The next patches will convert tcp and iser, and fix iser's dma_mask
bug.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Currently we duplicate the list of sessions, because we were using the
test for if a session was on the host list to indicate if the session
was bound or unbound. We can instead use the target_id and fix up
the class so that drivers like bnx2i do not have to manage the target id
space.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This is the second part of the iscsi task merging, and
all it does it rename iscsi_cmd_task to iscsi_task and
mtask/ctask to just task.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
There is no need to have the mgmt and cmd tasks separate
structs. It used to save a lot of memory when we overprealocated
memory for tasks, but the next patches will set up the
driver so in the future they can use a mempool or some other
common scsi command allocator and common tagging.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Currently to get a ctask from the session cmd array, you have to
know to use the itt modifier. To make this easier on LLDs and
so in the future we can easilly kill the session array and use
the host shared map instead, this patch adds a nice wrapper
to strip the itt into a session->cmds index and return a ctask.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Some drivers want to be able to just pass in the driver data pointers
to the iscsi objects. To enable this we need the iscsi printk macro
to cast the object.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This removes the session and conn data_size fields from the iscsi_transport.
Just pass in the value like with host allocation. This patch also makes
it so the LLD iscsi_conn data is allocated with the iscsi_cls_conn.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This finishes the host/session unbinding, by adding some helpers
to add and remove hosts and the session they manage.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Jens Axboe