Manage RoCE gid table with logic in IB/core, which is common to all
vendors, and remove the mechanism from the mlx4 IB driver.
Since management of the GID cache may lead to index mismatch with the
hardware GID table, a translation between indexes is required when
modifying a QP or creating an address handle.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
get_netdev: get the net_device on the physical port of the IB transport port. In
port aggregation mode it is required to return the netdev of the active port.
modify_gid: note for a change in the RoCE gid cache. Handle this by writing to
the harsware GID table. It is possible that indexes in cahce and hardware tables
won't match so a translation is required when modifying a QP or creating an
address handle.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Handling bonding and other devices require us to all all GIDs of the
net-devices which are upper-devices of the RoCE port related
net-device.
Active-backup configurations imposes even more challenges as the
default GID should only be set on the active devices (this is
necessary as otherwise the same MAC could be used for several
slaves and thus several slaves will have identical GIDs).
Managing these configurations are done by listening to:
(a) NETDEV_CHANGEUPPER event
(1) if a related net-device is linked, delete all inactive
slaves default GIDs and add the upper device GIDs.
(2) if a related net-device is unlinked, delete all upper GIDs
and add the default GIDs.
(b) NETDEV_BONDING_FAILOVER:
(1) delete the bond GIDs from inactive slaves
(2) delete the inactive slave's default GIDs
(3) Add the bond GIDs to the active slave.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Smatch says that, based on the indenting, we should probably add curly
braces here.
Fixes: 03db3a2d81 ('IB/core: Add RoCE GID table management')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
RoCE GIDs are based on IP addresses configured on Ethernet net-devices
which relate to the RDMA (RoCE) device port.
Currently, each of the low-level drivers that support RoCE (ocrdma,
mlx4) manages its own RoCE port GID table. As there's nothing which is
essentially vendor specific, we generalize that, and enhance the RDMA
core GID cache to do this job.
In order to populate the GID table, we listen for events:
(a) netdev up/down/change_addr events - if a netdev is built onto
our RoCE device, we need to add/delete its IPs. This involves
adding all GIDs related to this ndev, add default GIDs, etc.
(b) inet events - add new GIDs (according to the IP addresses)
to the table.
For programming the port RoCE GID table, providers must implement
the add_gid and del_gid callbacks.
RoCE GID management requires us to state the associated net_device
alongside the GID. This information is necessary in order to manage
the GID table. For example, when a net_device is removed, its
associated GIDs need to be removed as well.
RoCE mandates generating a default GID for each port, based on the
related net-device's IPv6 link local. In contrast to the GID based on
the regular IPv6 link-local (as we generate GID per IP address),
the default GID is also available when the net device is down (in
order to support loopback).
Locking is done as follows:
The patch modify the GID table code both for new RoCE drivers
implementing the add_gid/del_gid callbacks and for current RoCE and
IB drivers that do not. The flows for updating the table are
different, so the locking requirements are too.
While updating RoCE GID table, protection against multiple writers is
achieved via mutex_lock(&table->lock). Since writing to a table
requires us to find an entry (possible a free entry) in the table and
then modify it, this mutex protects both the find_gid and write_gid
ensuring the atomicity of the action.
Each entry in the GID cache is protected by rwlock. In RoCE, writing
(usually results from netdev notifier) involves invoking the vendor's
add_gid and del_gid callbacks, which could sleep.
Therefore, an invalid flag is added for each entry. Updates for RoCE are
done via a workqueue, thus sleeping is permitted.
In IB, updates are done in write_lock_irq(&device->cache.lock), thus
write_gid isn't allowed to sleep and add_gid/del_gid are not called.
When passing net-device into/out-of the GID cache, the device
is always passed held (dev_hold).
The code uses a single work item for updating all RDMA devices,
following a netdev or inet notifier.
The patch moves the cache from being a client (which was incorrect,
as the cache is part of the IB infrastructure) to being explicitly
initialized/freed when a device is registered/removed.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This gets rid of the weird in-between state where struct ib_device
was allocated but the kobject didn't work.
Consequently ib_device_release is now guaranteed to be called in
all situations and we needn't duplicate its kfrees on error paths.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Fully replaced by a more generic and suitable
ib_alloc_mr.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Use ib_alloc_mr with specific parameters.
Change the existing callers.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This was added in a thought of uniting all mr allocation
and deallocation routines but the fact is we have a single
deallocation routine already, ib_dereg_mr.
And, move mlx5_ib_destroy_mr specific logic into mlx5_ib_dereg_mr
(includes only signature stuff for now).
And, fixup the only callers (iser/isert) accordingly.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When no matching listening ID is found for a given request, the net_dev
that was used to find the request isn't released.
Fixes: 0b3ca768fc ("IB/cma: Use found net_dev for passive connections")
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Now that there are no ib_cm clients using the compare_data feature for
matching IB CM requests' private data, remove the compare_data parameter of
ib_cm_listen and remove the code implementing the feature.
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Use ib_cm_insert_listen to create listening IB CM IDs or share existing
ones if needed. When given a request on a specific CM ID, the code now
matches the request to the RDMA CM ID based on the request parameters, so
it no longer needs to rely on the ib_cm's private data matching
capabilities.
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When receiving a new connection in cma_req_handler, we actually already
know the net_dev that is used for the connection's creation. Instead of
calling cma_translate_addr to resolve the new connection id's source
address, just use the net_dev that was found.
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Pass incoming request parameters through the relevant IPv4/IPv6 routing
tables and make sure the network stack is configured to handle such
requests.
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Instead of relying on a the ib_cm module to check an incoming CM request's
private data header, add these checks to the RDMA CM module. This allows a
following patch to to clean up the ib_cm interface and remove the code that
looks into the private headers. It will also allow supporting namespaces in
RDMA CM by making these checks namespace aware later on.
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The rdma_cm module will later use the P_Key from the BTH to de-mux
requests.
See discussion at:
http://www.spinics.net/lists/netdev/msg336067.html
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Liran Liss <liranl@mellanox.com>
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add helper functions to access the IDRs by port-space and port number.
Pass around the port-space enum in cma.c instead of using pointers to
port-space IDRs.
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Yotam Kenneth <yotamke@mellanox.com>
Signed-off-by: Shachar Raindel <raindel@mellanox.com>
Signed-off-by: Guy Shapiro <guysh@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When receiving a connection request, rdma_cm needs to associate the request
with a network device, in order to disambiguate requests. To do this, it
needs to know the request's destination IP. For this the module needs to
allow getting this information from the private data in the request packet,
instead of relying on the information already being in the listening RDMA
CM ID.
When creating a new incoming connection ID, the code in
cma_save_ip{4,6}_info can no longer rely on the listener's private data to
find the port number, so it reads it from the requested service ID.
Signed-off-by: Guy Shapiro <guysh@mellanox.com>
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Yotam Kenneth <yotamke@mellanox.com>
Signed-off-by: Shachar Raindel <raindel@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Enabling network namespaces for RDMA CM will allow processes on different
namespaces to listen on the same port. In order to leave namespace support
out of the CM layer, this requires that multiple RDMA CM IDs will be able
to share a single CM ID.
This patch adds infrastructure to retrieve an existing listening ib_cm_id,
based on its device and service ID, or create a new one if one does not
already exist. It also adds a reference count for such instances
(cm_id_private.listen_sharecount), and prevents cm_destroy_id from
destroying a CM if it is still shared. See the relevant discussion [1].
[1] Re: [PATCH v3 for-next 05/13] IB/cm: Reference count ib_cm_ids
http://www.spinics.net/lists/netdev/msg328860.html
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Expose the service ID on an incoming CM or SIDR request to the event
handler. This will allow the RDMA CM module to de-multiplex connection
requests based on the information encoded in the service ID.
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Implement the get_net_device_by_port_pkey_ip callback that returns network
device to ib_core according to connection parameters. Check the ipoib
device and iterate over all child devices to look for a match.
For each IPoIB device we iterate through all upper devices when searching
for a matching IP, in order to support bonding.
Signed-off-by: Guy Shapiro <guysh@mellanox.com>
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Yotam Kenneth <yotamke@mellanox.com>
Signed-off-by: Shachar Raindel <raindel@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In the case of IPoIB, and maybe in other cases, the network device is
managed by an upper-layer protocol (ULP). In order to expose this
network device to other users of the IB device, let ULPs implement
a callback that returns network device according to connection parameters.
The IB device and port, together with the P_Key and the GID should
be enough to uniquely identify the ULP net device. However, in current
kernels there can be multiple IPoIB interfaces created with the same GID.
Furthermore, such configuration may be desireable to support ipvlan-like
configurations for RDMA CM with IPoIB. To resolve the device in these
cases the code will also take the IP address as an additional input.
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Yotam Kenneth <yotamke@mellanox.com>
Signed-off-by: Shachar Raindel <raindel@mellanox.com>
Signed-off-by: Guy Shapiro <guysh@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
An ib_client callback that is called with the lists_rwsem locked only for
read is protected from changes to the IB client lists, but not from
ib_unregister_device() freeing its client data. This is because
ib_unregister_device() will remove the device from the device list with
lists_rwsem locked for write, but perform the rest of the cleanup,
including the call to remove() without that lock.
Mark client data that is undergoing de-registration with a new going_down
flag in the client data context. Lock the client data list with lists_rwsem
for write in addition to using the spinlock, so that functions calling the
callback would be able to lock only lists_rwsem for read and let callbacks
sleep.
Since ib_unregister_client() now marks the client data context, no need for
remove() to search the context again, so pass the client data directly to
remove() callbacks.
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Currently the RDMA subsystem's device list and client list are protected by
a single mutex. This prevents adding user-facing APIs that iterate these
lists, since using them may cause a deadlock. The patch attempts to solve
this problem by adding a read-write semaphore to protect the lists. Readers
now don't need the mutex, and are safe just by read-locking the semaphore.
The ib_register_device, ib_register_client, ib_unregister_device, and
ib_unregister_client functions are modified to lock the semaphore for write
during their respective list modification. Also, in order to make sure
client callbacks are called only between add() and remove() calls, the code
is changed to only add items to the lists after the add() calls and remove
from the lists before the remove() calls.
This patch attempts to solve a similar need [1] that was seen in the RoCE
v2 patch series.
[1] http://www.spinics.net/lists/linux-rdma/msg24733.html
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Matan Barak <matanb@mellanox.com>
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Applications must not assume that max_sge and max_sge_rd are the same,
Hence expose max_sge_rd correctly as well.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Acked-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Applications must not assume that max_sge and max_sge_rd are the same,
Hence expose max_sge_rd correctly as well.
Reported-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch adds the value of the CNP opcode to the existing list of enumerated
opcodes in ib_pack.h
Add common OPA header definitions for driver
build:
- opa_port_info.h
- opa_smi.h
- hfi1_user.h
Additionally, ib_mad.h, has additional definitions
that are common to ib_drivers including:
- trap support
- cca support
The qib driver has the duplication removed in favor
those in ib_mad.h
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: John, Jubin <jubin.john@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The HW hasn't been sold since 2005, and the SW has definite bit rot.
Its time to remove it. So move it to staging for a few releases and
then remove it after that.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
It is now time for the ipath driver to begin to be phased out of the kernel.
This patch moves the ipath driver from the Infiniband sub tree to the staging
area where it will remain until the code is removed from the kernel in a few
releases.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add support for ipv6 address handling clip api provided by lld
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Resolving a link-local IPv6 address with an unspecified source address
was broken by commit 5462eddd7a, which prevented the IPv6 stack from
learning the scope id of the link-local IPv6 address, causing random
failures as the IP stack chose a random link to resolve the address on.
This commit 5462eddd7a made us bail out of cma_check_linklocal early if
the address passed in was not an IPv6 link-local address. On the address
resolution path, the address passed in is the source address; if the
source address is the unspecified address, which is not link-local, we
will bail out early.
This is mostly correct, but if the destination address is a link-local
address, then we will be following a link-local route, and we'll need to
tell the IPv6 stack what the scope id of the destination address is.
This used to be done by last line of cma_check_linklocal, which is
skipped when bailing out early:
dev_addr->bound_dev_if = sin6->sin6_scope_id;
(In cma_bind_addr, the sin6_scope_id of the source address is set to the
sin6_scope_id of the destination address, so this is correct)
This line is required in turn for the following line, L279 of
addr6_resolve, to actually inform the IPv6 stack of the scope id:
fl6.flowi6_oif = addr->bound_dev_if;
Since we can only know we are in this failure case when we have access
to both the source IPv6 address and destination IPv6 address, we have to
deal with this further up the stack. So detect this failure case in
cma_bind_addr, and set bound_dev_if to the destination address scope id
to correct it.
Signed-off-by: Spencer Baugh <sbaugh@catern.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Something like this:
CPU A CPU B
Acked-by: Sean Hefty <sean.hefty@intel.com>
======================== ================================
ucma_destroy_id()
wait_for_completion()
.. anything
ucma_put_ctx()
complete()
.. continues ...
ucma_leave_multicast()
mutex_lock(mut)
atomic_inc(ctx->ref)
mutex_unlock(mut)
ucma_free_ctx()
ucma_cleanup_multicast()
mutex_lock(mut)
kfree(mc)
rdma_leave_multicast(mc->ctx->cm_id,..
Fix it by latching the ref at 0. Once it goes to 0 mc and ctx cannot
leave the mutex(mut) protection.
The other atomic_inc in ucma_get_ctx is OK because mutex(mut) protects
it from racing with ucma_destroy_id.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This enables ORD/IRD negotiation and its about time to enable it by
default
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Currently the sg tablesize, which dictates fast register page list
depth to use, does not take into account the limits of the rdma device.
So adjust it once we discover the device fastreg max depth limit. Also
adjust the max_sectors based on the resulting sg tablesize.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The only place that assigns mr inside the loop already does a break.
So "if (mr)" will never be true here since the function initializes mr
to NULL at the top. We can just drop the extra if and break here.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Acked-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The lkey table is allocated with with a get_user_pages() with an
order based on a number of index bits from a module parameter.
The underlying kernel code cannot allocate that many contiguous pages.
There is no reason the underlying memory needs to be physically
contiguous.
This patch:
- switches the allocation/deallocation to vmalloc/vfree
- caps the number of bits to 23 to insure at least 1 generation bit
o this matches the module parameter description
Cc: stable@vger.kernel.org
Reviewed-by: Vinit Agnihotri <vinit.abhay.agnihotri@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Should be all the page sizes that are supported by the
device.
Reported-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The mlx5 driver exposes device capability IB_DEVICE_LOCAL_DMA_LKEY
but does not set the the device local_dma_lkey. This breaks
rpcrdma drivers.
Query and set this lkey when creating the device resources.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
It appears to be what the rest of the kernel does, so let's do it too.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Very similar to how it went with local_sockaddr.
It was embedded in iscsi_login_stats so some changes there, and we needed
to copy in a sockaddr_storage comparison function. Hopefully the kernel
will get a standard one soon, our implementation makes the 3rd.
isert_set_conn_info() became much smaller.
IPV6_ADDRESS_SPACE define goes away, had to modify a call to in6_pton(),
can just use -1 since we are sure string is null-terminated.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This is a more natural format that lets us format it with the appropriate
printk specifier as needed.
This also lets us handle v4-mapped ipv6 addresses a little more nicely, by
storing the addr as an actual v4 sockaddr in conn->local_sockaddr.
Finally, we no longer need to maintain variables for port, since this is
contained in sockaddr. Remove iscsi_np.np_port and iscsi_conn.local_port.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The verbs are obsolete. The ib_rereg_phys_mr() verb is not used by
kernel ULPs, and the last ib_reg_phys_mr() call site in the kernel
tree has now been removed.
Two staging tree call sites remain in the Lustre client. The Lustre
team has been notified of the deprecation of reg_phys_mr.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Acked-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Conflicts:
arch/s390/net/bpf_jit_comp.c
drivers/net/ethernet/ti/netcp_ethss.c
net/bridge/br_multicast.c
net/ipv4/ip_fragment.c
All four conflicts were cases of simple overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull SCSI target fixes from Nicholas Bellinger:
"This series is larger than what I'd normally be conformable with
sending for a -rc5 PULL request..
However, the bulk of the series is localized to qla2xxx target
specific fixes that address a number of real-world correctness issues,
that have been outstanding on the list for ~6 weeks now. They where
submitted + verified + acked by the HW LLD vendor, contributed by a
major production customer of the code, and are marked for v3.18.y
stable code.
That said, I don't see a good reason to wait another month to get
these fixes into mainline.
Beyond the qla2xx specific fixes, this series also includes:
- bugfix for a long standing use-after-free in iscsi-target during
TPG shutdown + demo-mode sessions.
- bugfix for a >= v4.0 regression OOPs in iscsi-target during a
iscsi_start_kthreads() failure.
- bugfix for a >= v4.0 regression hang in iscsi-target for iser
explicit session/connection logout.
- bugfix for a iser-target bug where a early CMA REJECTED status
during login triggers a NULL pointer dereference OOPs.
- bugfixes for a handful of v4.2-rc1 specific regressions related to
the larger set of recent backend configfs attribute changes.
A big thanks to QLogic + Pure Storage for the qla2xxx target bugfixes"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (28 commits)
Documentation/target: Fix tcm_mod_builder.py build breakage
iser-target: Fix REJECT CM event use-after-free OOPs
iscsi-target: Fix iser explicit logout TX kthread leak
iscsi-target: Fix iscsit_start_kthreads failure OOPs
iscsi-target: Fix use-after-free during TPG session shutdown
qla2xxx: terminate exchange when command is aborted by LIO
qla2xxx: drop cmds/tmrs arrived while session is being deleted
qla2xxx: disable scsi_transport_fc registration in target mode
qla2xxx: added sess generations to detect RSCN update races
qla2xxx: Abort stale cmds on qla_tgt_wq when plogi arrives
qla2xxx: delay plogi/prli ack until existing sessions are deleted
qla2xxx: cleanup cmd in qla workqueue before processing TMR
qla2xxx: kill sessions/log out initiator on RSCN and port down events
qla2xxx: fix command initialization in target mode.
qla2xxx: Remove msleep in qlt_send_term_exchange
qla2xxx: adjust debug flags
qla2xxx: release request queue reservation.
qla2xxx: Add flush after updating ATIOQ consumer index.
qla2xxx: Enable target mode for ISP27XX
qla2xxx: Fix hardware lock/unlock issue causing kernel panic.
...
c4iw_poll_cq_on() shouldn't fail the poll operation just because
the CQE status is unknown. Rather, it should map this to the
"fatal error" status and log the anomaly.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
To add Hardware accelerated support in 802.1ad vlan, replace
Current VLAN macros to CVLAN.
Replace:
MLX4_WQE_CTRL_INS_VLAN
MLX4_CQE_VLAN_PRESENT_MASK
With:
MLX4_WQE_CTRL_INS_CVLAN
MLX4_CQE_CVLAN_PRESENT_MASK
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a bug in iser-target code where the REJECT CM event
handler code currently performs a isert_put_conn() for the final
isert_conn->kref put, while iscsi_np process context is still blocked
in isert_get_login_rx().
Once isert_get_login_rx() is awoking due to login timeout, iscsi_np
process context will attempt to invoke iscsi_target_login_sess_out()
to cleanup iscsi_conn as expected, and calls isert_wait_conn() +
isert_free_conn() which triggers the use-after-free OOPs.
To address this bug, move the kref_get_unless_zero() call from
isert_connected_handler() into isert_connect_request() immediately
preceeding isert_rdma_accept() to ensure the CM handler cleanup
paths and isert_free_conn() are always operating with two refs.
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Change of license from GPLv2 to dual-license (GPLv2 and BSD 2-Clause)
All contributors were contacted off-list and permission to make this
change was received. The complete list of contributors are Cc:ed here.
Cc: Tejun Heo <tj@kernel.org>
Cc: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Jes Sorensen <Jes.Sorensen@redhat.com>
Cc: Sasha Levin <levinsasha928@gmail.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Cc: Moni Shoua <monis@mellanox.com>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Li RongQing <roy.qing.li@gmail.com>
Cc: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: Devesh Sharma <devesh.sharma@avagotech.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
If the above is turned off then ipoib_cm_dev_init unconditionally
returns ENOSYS, and the newly added error handling in
0b3957 prevents ipoib from coming up at all:
kernel: mlx4_0: ipoib_transport_dev_init failed
kernel: mlx4_0: failed to initialize port 1 (ret = -12)
Fixes: 0b39578bcd (IB/ipoib: Use dedicated workqueues per interface)
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
T3 HW only supports 32 bit MRs. If the system uses 64 bit memory
addresses, then a registered 32 bit MR will wrap and write to the
wrong memory when used with addresses > 4GB. To prevent this,
simply fail to allocate an MR on 64 bit machines (other means
of registering memory are still available and software can still
work, we just don't allow this means of memory registration).
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
There is little chance our memory allocation will fail, so we can
combine initializing the work structs with allocating them instead of
looping through all of them once to allocate and again to initialize.
Then when we need to actually find out if our device is up or in the
process of going down, have all of our work structs batched up, take the
spin_lock once and only once, and do all of the batch under the one
spin_lock invocation instead of incurring all of the locked memory cycles
we would otherwise incur to take/release the spin_lock over and over
again.
Signed-off-by: Doug Ledford <dledford@redhat.com>
We create a number of work structs to be queued up to a workqueue, and
on completion of the workqueue handler, the workqueue handler frees the
allocated memory. If, however, we don't queue the work struct because
the device is going down, then we need to free the memory ourselves.
Signed-off-by: Doug Ledford <dledford@redhat.com>
On failure, we loop through all possible pointers and test them before
calling kfree. But really, why even attempt to free items we didn't
allocate when we can easily loop through exactly and only the devices
for which the original memory allocation succeeded and free just those.
Signed-off-by: Maninder Singh <maninder1.s@samsung.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
For IB links, reading HCA flow counters through iboe_process_mad() should
be used when mlx4_ib_process_mad() is invoked only for VFs PMA queries and
exactly nothing else.
Fixes: 7193a141eb ('IB/mlx4: Set VF to read from QP counters')
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In little endian cases, the macros be16_to_cpu and cpu_to_be64
unfolds to __swab{16,64} which provides special case for constants.
In big endian cases, __constant_be16_to_cpu and be16_to_cpu
expand directly to the same expression. The same applies for
__constant_cpu_to_be64 and cpu_to_be64.
So, replace __constant_be16_to_cpu with be16_to_cpu and
__constant_cpu_to_be64 with cpu_to_be64, with the goal of getting
rid of the definition of __constant_be16_to_cpu and
__constant_cpu_to_be64 completely.
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When switching between modes (datagram / connected) change the MTU
accordingly.
datagram mode up to 4K, connected mode up to (64K - 0x10).
Signed-off-by: ELi Cohen <eli@mellanox.com>
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
By default, IPoIB-CM driver uses 64k MTU. Larger MTU gives better
performance.
This MTU plus overhead puts the memory allocation for IP based packets at
32 4k pages (order 5), which have to be contiguous.
When the system memory under pressure, it was observed that allocating 128k
contiguous physical memory is difficult and causes serious errors (such as
system becomes unusable).
This enhancement resolve the issue by removing the physically contiguous
memory requirement using Scatter/Gather feature that exists in Linux stack.
With this fix Scatter-Gather will be supported also in connected mode.
This change reverts some of the change made in commit e112373fd6
("IPoIB/cm: Reduce connected mode TX object size").
The ability to use SG in IPoIB CM is possible because the coupling
between NETIF_F_SG and NETIF_F_CSUM was removed in commit
ec5f061564 ("net: Kill link between CSUM and SG features.")
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Acked-by: Christian Marie <christian@ponies.io>
Signed-off-by: Doug Ledford <dledford@redhat.com>
ib_ucm_release_dev clears the wrong bit if devnum is greater
than IB_UCM_MAX_DEVICES.
Signed-off-by: Carol L Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Fix for incorrect recording of the MAC address
Signed-off-by: Tatyana Nikolova <Tatyana.E.Nikolova@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Neighbor resolution doesn't work without this fix
Signed-off-by: Tatyana Nikolova <Tatyana.E.Nikolova@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Fixes to allow clients to make remove mapping requests, after
they have provided the user space service with the mapping
information, they are using when the service is restarted.
1) Adding IWPM_REG_VALID, IWPM_REG_INCOMPL and IWPM_REG_UNDEF
registration types for the port mapper clients and functions
to set/check the registration type.
2) If the port mapper user space service is not available to register
the client, then its registration stays IWPM_REG_UNDEF and the
registration isn't checked until the service becomes available
(no mappings are possible, if the user space service isn't running).
3) After the service is restarted, the user space port mapper pid is set
to valid and the client registration is set to IWPM_REG_INCOMPL
to allow the client to make remove mapping requests.
Signed-off-by: Tatyana Nikolova <Tatyana.E.Nikolova@intel.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Tested-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Error values of ib_query_port() and ib_query_device() weren't propagated
correctly. Because of that, ipoib_add_port() could return NULL value,
which escaped the IS_ERR() check in ipoib_add_one() and we crashed.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
mlx4 VFs can provide CQE raw time-stamping services, but they
don't have the hca core clock mapped to their PCI bars.
As such, we should not attempt to query and report the clock offset
to user space for VFs. Doing so causes query_device over VFs to fail
with -ENOSUPP.
Fixes: 4b664c4355 ('IB/mlx4: Add support for CQ time-stamping')
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Whenever ib_cm gets remove_one call, like when there is a hot-unplug
event, the driver should mark itself as going_down and confirm that no
new works are going to be queued for that device.
so, the order of the actions are:
1. mark the going_down bit.
2. flush the wq.
3. [make sure no new works for that device.]
4. unregister mad agent.
otherwise, works that are already queued can be scheduled after the mad
agent was freed.
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
We might return res which is not initialized. Also
reduce code duplication by exporting srp_parse_tmo so
srp_tmo_set can reuse it.
Detected by Coverity.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Jenny Falkovich <jennyf@mellanox.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In little endian cases, the macro cpu_to_be{16,32,64} unfolds to
__swab{16,32,64} which provides special case for constants. In
big endian cases, __constant_cpu_to_be{16,32,64} and
cpu_to_be{16,32,64} expand directly to the same expression. So,
replace __constant_cpu_to_be{16,32,64} with cpu_to_be{16,32,64}
with the goal of getting rid of the definitions of
__constant_cpu_to_be{16,32,64} completely.
The Coccinelle semantic patch that performs this transformation
is as follows:
@@expression x;@@
(
- __constant_cpu_to_be16(x)
+ cpu_to_be16(x)
|
- __constant_cpu_to_be32(x)
+ cpu_to_be32(x)
|
- __constant_cpu_to_be64(x)
+ cpu_to_be64(x)
)
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
We recently added BUG_ON's which were inappropriate for a condition which
should never happen. Change these to be WARN_ON_ONCE as a debugging aid.
Fixes: 4cd7c9479a ('IB/mad: Add support for additional MAD info to/from drivers')
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The define OPA_LID_PERMISSIVE is big endian and was compared to the
cpu endian variable opa_drslid.
Problem caught by 0-day build infrastructure.
Fixes: 8e4349d13f (IB/mad: Add final OPA MAD processing)
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: John, Jubin <jubin.john@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Persuant to Liran's comments on node_type on linux-rdma
mailing list:
In an effort to reform the RDMA core and ULPs to minimize use of
node_type in struct ib_device, an additional bit is added to
struct ib_device for is_switch (IB switch). This is needed
to be initialized by any IB switch device driver. This is a
NEW requirement on such device drivers which are all
"out of tree".
In addition, an ib_switch helper was added to ib_verbs.h
based on the is_switch device bit rather than node_type
(although those should be consistent).
The RDMA core (MAD, SMI, agent, sa_query, multicast, sysfs)
as well as (IPoIB and SRP) ULPs are updated where
appropriate to use this new helper. In some cases,
the helper is now used under the covers of using
rdma_[start end]_port rather than the open coding
previously used.
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Reviewed-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Tested-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Hal Rosenstock <hal@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Pull more vfs updates from Al Viro:
"Assorted VFS fixes and related cleanups (IMO the most interesting in
that part are f_path-related things and Eric's descriptor-related
stuff). UFS regression fixes (it got broken last cycle). 9P fixes.
fs-cache series, DAX patches, Jan's file_remove_suid() work"
[ I'd say this is much more than "fixes and related cleanups". The
file_table locking rule change by Eric Dumazet is a rather big and
fundamental update even if the patch isn't huge. - Linus ]
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (49 commits)
9p: cope with bogus responses from server in p9_client_{read,write}
p9_client_write(): avoid double p9_free_req()
9p: forgetting to cancel request on interrupted zero-copy RPC
dax: bdev_direct_access() may sleep
block: Add support for DAX reads/writes to block devices
dax: Use copy_from_iter_nocache
dax: Add block size note to documentation
fs/file.c: __fget() and dup2() atomicity rules
fs/file.c: don't acquire files->file_lock in fd_install()
fs:super:get_anon_bdev: fix race condition could cause dev exceed its upper limitation
vfs: avoid creation of inode number 0 in get_next_ino
namei: make set_root_rcu() return void
make simple_positive() public
ufs: use dir_pages instead of ufs_dir_pages()
pagemap.h: move dir_pages() over there
remove the pointless include of lglock.h
fs: cleanup slight list_entry abuse
xfs: Correctly lock inode when removing suid and file capabilities
fs: Call security_ops->inode_killpriv on truncate
fs: Provide function telling whether file_remove_privs() will do anything
...
Pull SCSI target updates from Nicholas Bellinger:
"It's been a busy development cycle for target-core in a number of
different areas.
The fabric API usage for se_node_acl allocation is now within
target-core code, dropping the external API callers for all fabric
drivers tree-wide.
There is a new conversion to RCU hlists for se_node_acl and
se_portal_group LUN mappings, that turns fast-past LUN lookup into a
completely lockless code-path. It also removes the original
hard-coded limitation of 256 LUNs per fabric endpoint.
The configfs attributes for backends can now be shared between core
and driver code, allowing existing drivers to use common code while
still allowing flexibility for new backend provided attributes.
The highlights include:
- Merge sbc_verify_dif_* into common code (sagi)
- Remove iscsi-target support for obsolete IFMarker/OFMarker
(Christophe Vu-Brugier)
- Add bidi support in target/user backend (ilias + vangelis + agover)
- Move se_node_acl allocation into target-core code (hch)
- Add crc_t10dif_update common helper (akinobu + mkp)
- Handle target-core odd SGL mapping for data transfer memory
(akinobu)
- Move transport ID handling into target-core (hch)
- Move task tag into struct se_cmd + support 64-bit tags (bart)
- Convert se_node_acl->device_list[] to RCU hlist (nab + hch +
paulmck)
- Convert se_portal_group->tpg_lun_list[] to RCU hlist (nab + hch +
paulmck)
- Simplify target backend driver registration (hch)
- Consolidate + simplify target backend attribute implementations
(hch + nab)
- Subsume se_port + t10_alua_tg_pt_gp_member into se_lun (hch)
- Drop lun_sep_lock for se_lun->lun_se_dev RCU usage (hch + nab)
- Drop unnecessary core_tpg_register TFO parameter (nab)
- Use 64-bit LUNs tree-wide (hannes)
- Drop left-over TARGET_MAX_LUNS_PER_TRANSPORT limit (hannes)"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (76 commits)
target: Bump core version to v5.0
target: remove target_core_configfs.h
target: remove unused TARGET_CORE_CONFIG_ROOT define
target: consolidate version defines
target: implement WRITE_SAME with UNMAP bit using ->execute_unmap
target: simplify UNMAP handling
target: replace se_cmd->execute_rw with a protocol_data field
target/user: Fix inconsistent kmap_atomic/kunmap_atomic
target: Send UA when changing LUN inventory
target: Send UA upon LUN RESET tmr completion
target: Send UA on ALUA target port group change
target: Convert se_lun->lun_deve_lock to normal spinlock
target: use 'se_dev_entry' when allocating UAs
target: Remove 'ua_nacl' pointer from se_ua structure
target_core_alua: Correct UA handling when switching states
xen-scsiback: Fix compile warning for 64-bit LUN
target: Remove TARGET_MAX_LUNS_PER_TRANSPORT
target: use 64-bit LUNs
target: Drop duplicate + unused se_dev_check_wce
target: Drop unnecessary core_tpg_register TFO parameter
...
Merge third patchbomb from Andrew Morton:
- the rest of MM
- scripts/gdb updates
- ipc/ updates
- lib/ updates
- MAINTAINERS updates
- various other misc things
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (67 commits)
genalloc: rename of_get_named_gen_pool() to of_gen_pool_get()
genalloc: rename dev_get_gen_pool() to gen_pool_get()
x86: opt into HAVE_COPY_THREAD_TLS, for both 32-bit and 64-bit
MAINTAINERS: add zpool
MAINTAINERS: BCACHE: Kent Overstreet has changed email address
MAINTAINERS: move Jens Osterkamp to CREDITS
MAINTAINERS: remove unused nbd.h pattern
MAINTAINERS: update brcm gpio filename pattern
MAINTAINERS: update brcm dts pattern
MAINTAINERS: update sound soc intel patterns
MAINTAINERS: remove website for paride
MAINTAINERS: update Emulex ocrdma email addresses
bcache: use kvfree() in various places
libcxgbi: use kvfree() in cxgbi_free_big_mem()
target: use kvfree() in session alloc and free
IB/ehca: use kvfree() in ipz_queue_{cd}tor()
drm/nouveau/gem: use kvfree() in u_free()
drm: use kvfree() in drm_free_large()
cxgb4: use kvfree() in t4_free_mem()
cxgb3: use kvfree() in cxgb_free_mem()
...
Main excitement here is Peter Zijlstra's lockless rbtree optimization to
speed module address lookup. He found some abusers of the module lock
doing that too.
A little bit of parameter work here too; including Dan Streetman's breaking
up the big param mutex so writing a parameter can load another module (yeah,
really). Unfortunately that broke the usual suspects, !CONFIG_MODULES and
!CONFIG_SYSFS, so those fixes were appended too.
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tWPQ
-----END PGP SIGNATURE-----
Merge tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module updates from Rusty Russell:
"Main excitement here is Peter Zijlstra's lockless rbtree optimization
to speed module address lookup. He found some abusers of the module
lock doing that too.
A little bit of parameter work here too; including Dan Streetman's
breaking up the big param mutex so writing a parameter can load
another module (yeah, really). Unfortunately that broke the usual
suspects, !CONFIG_MODULES and !CONFIG_SYSFS, so those fixes were
appended too"
* tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (26 commits)
modules: only use mod->param_lock if CONFIG_MODULES
param: fix module param locks when !CONFIG_SYSFS.
rcu: merge fix for Convert ACCESS_ONCE() to READ_ONCE() and WRITE_ONCE()
module: add per-module param_lock
module: make perm const
params: suppress unused variable error, warn once just in case code changes.
modules: clarify CONFIG_MODULE_COMPRESS help, suggest 'N'.
kernel/module.c: avoid ifdefs for sig_enforce declaration
kernel/workqueue.c: remove ifdefs over wq_power_efficient
kernel/params.c: export param_ops_bool_enable_only
kernel/params.c: generalize bool_enable_only
kernel/module.c: use generic module param operaters for sig_enforce
kernel/params: constify struct kernel_param_ops uses
sysfs: tightened sysfs permission checks
module: Rework module_addr_{min,max}
module: Use __module_address() for module_address_lookup()
module: Make the mod_tree stuff conditional on PERF_EVENTS || TRACING
module: Optimize __module_address() using a latched RB-tree
rbtree: Implement generic latch_tree
seqlock: Introduce raw_read_seqcount_latch()
...
Use kvfree() instead of open-coding it.
Signed-off-by: Pekka Enberg <penberg@kernel.org>
Cc: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Cc: Christoph Raisch <raisch@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking updates from David Miller:
1) Add TX fast path in mac80211, from Johannes Berg.
2) Add TSO/GRO support to ibmveth, from Thomas Falcon
3) Move away from cached routes in ipv6, just like ipv4, from Martin
KaFai Lau.
4) Lots of new rhashtable tests, from Thomas Graf.
5) Run ingress qdisc lockless, from Alexei Starovoitov.
6) Allow servers to fetch TCP packet headers for SYN packets of new
connections, for fingerprinting. From Eric Dumazet.
7) Add mode parameter to pktgen, for testing receive. From Alexei
Starovoitov.
8) Cache access optimizations via simplifications of build_skb(), from
Alexander Duyck.
9) Move page frag allocator under mm/, also from Alexander.
10) Add xmit_more support to hv_netvsc, from KY Srinivasan.
11) Add a counter guard in case we try to perform endless reclassify
loops in the packet scheduler.
12) Extern flow dissector to be programmable and use it in new "Flower"
classifier. From Jiri Pirko.
13) AF_PACKET fanout rollover fixes, performance improvements, and new
statistics. From Willem de Bruijn.
14) Add netdev driver for GENEVE tunnels, from John W Linville.
15) Add ingress netfilter hooks and filtering, from Pablo Neira Ayuso.
16) Fix handling of epoll edge triggers in TCP, from Eric Dumazet.
17) Add an ECN retry fallback for the initial TCP handshake, from Daniel
Borkmann.
18) Add tail call support to BPF, from Alexei Starovoitov.
19) Add several pktgen helper scripts, from Jesper Dangaard Brouer.
20) Add zerocopy support to AF_UNIX, from Hannes Frederic Sowa.
21) Favor even port numbers for allocation to connect() requests, and
odd port numbers for bind(0), in an effort to help avoid
ip_local_port_range exhaustion. From Eric Dumazet.
22) Add Cavium ThunderX driver, from Sunil Goutham.
23) Allow bpf programs to access skb_iif and dev->ifindex SKB metadata,
from Alexei Starovoitov.
24) Add support for T6 chips in cxgb4vf driver, from Hariprasad Shenai.
25) Double TCP Small Queues default to 256K to accomodate situations
like the XEN driver and wireless aggregation. From Wei Liu.
26) Add more entropy inputs to flow dissector, from Tom Herbert.
27) Add CDG congestion control algorithm to TCP, from Kenneth Klette
Jonassen.
28) Convert ipset over to RCU locking, from Jozsef Kadlecsik.
29) Track and act upon link status of ipv4 route nexthops, from Andy
Gospodarek.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1670 commits)
bridge: vlan: flush the dynamically learned entries on port vlan delete
bridge: multicast: add a comment to br_port_state_selection about blocking state
net: inet_diag: export IPV6_V6ONLY sockopt
stmmac: troubleshoot unexpected bits in des0 & des1
net: ipv4 sysctl option to ignore routes when nexthop link is down
net: track link-status of ipv4 nexthops
net: switchdev: ignore unsupported bridge flags
net: Cavium: Fix MAC address setting in shutdown state
drivers: net: xgene: fix for ACPI support without ACPI
ip: report the original address of ICMP messages
net/mlx5e: Prefetch skb data on RX
net/mlx5e: Pop cq outside mlx5e_get_cqe
net/mlx5e: Remove mlx5e_cq.sqrq back-pointer
net/mlx5e: Remove extra spaces
net/mlx5e: Avoid TX CQE generation if more xmit packets expected
net/mlx5e: Avoid redundant dev_kfree_skb() upon NOP completion
net/mlx5e: Remove re-assignment of wq type in mlx5e_enable_rq()
net/mlx5e: Use skb_shinfo(skb)->gso_segs rather than counting them
net/mlx5e: Static mapping of netdev priv resources to/from netdev TX queues
net/mlx4_en: Use HW counters for rx/tx bytes/packets in PF device
...
This is the usual grab bag of driver updates (lpfc, hpsa,
megaraid_sas, cxgbi, be2iscsi) plus an assortment of minor updates.
There are also one new driver: the Cisco snic; the advansys driver has
been rewritten to get rid of the warning about converting it to the
DMA API, the tape statistics patch got in and finally, there's a
resuffle of SCSI header files to separate more cleanly initiator from
target mode (and better share the common definitions).
Signed-off-by: James Bottomley <JBottomley@Odin.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJViKWdAAoJEDeqqVYsXL0MAr8IAMmlA6HBVjMJJFCEOY9corHj
e70MNQa7LUgf+JCdOtzGcvHXTiFFd4IHZAwXUJAnsC4IU2QWEfi1bjUTErlqBIGk
LoZlXXpEHnFpmWot3OluOzzcGcxede8rVgPiKWVVdojIngBC2+LL/i2vPCJ84ri9
WCVlk6KBvWZXuU6JuOKAb2FO9HOX7Q61wuKAMast2Qc6RNc2ksgc7VbstsITqzZ9
FVEsjmQ5lqUj+xdxBpiUOdUpc22IJ4VcpBgQ2HrThvg6vf4aq937RJ/g4vi/g0SU
Utk0a3bUw1H/WnYAfJVFx83nVEsS/954Z7/ERDg1sjlfLYwQtQnpov0XIbPIbZU=
=k9IT
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is the usual grab bag of driver updates (lpfc, hpsa,
megaraid_sas, cxgbi, be2iscsi) plus an assortment of minor updates.
There is also one new driver: the Cisco snic. The advansys driver has
been rewritten to get rid of the warning about converting it to the
DMA API, the tape statistics patch got in and finally, there's a
resuffle of SCSI header files to separate more cleanly initiator from
target mode (and better share the common definitions)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (156 commits)
snic: driver for Cisco SCSI HBA
qla2xxx: Fix indentation
qla2xxx: Comment out unreachable code
fusion: remove dead MTRR code
advansys: fix compilation errors and warnings when CONFIG_PCI is not set
mptsas: fix depth param in scsi_track_queue_full
megaraid: fix irq setup process regression
lpfc: Update version to 10.7.0.0 for upstream patch set.
lpfc: Fix to drop PLOGIs from fabric node till LOGO processing completes
lpfc: Fix scsi task management error message.
lpfc: Fix cq_id masking problem.
lpfc: Fix scsi prep dma buf error.
lpfc: Add support for using block multi-queue
lpfc: Devices are not discovered during takeaway/giveback testing
lpfc: Fix vport deletion failure.
lpfc: Check for active portpeerbeacon.
lpfc: Update driver version for upstream patch set 10.6.0.1.
lpfc: Change buffer pool empty message to miscellaneous category
lpfc: Fix incorrect log message reported for empty FCF record.
lpfc: Fix rport leak.
...
- A large cleanup of how device capabilities are checked for various
features
- Additional cleanups in the MAD processing
- Update to the srp driver
- Creation and use of centralized log message helpers
- Add const to a number of args to calls and clean up call chain
- Add support for extended cq create verb
- Add support for timestamps on cq completion
- Add support for processing OPA MAD packets
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=yISf
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma updates from Doug Ledford:
- a large cleanup of how device capabilities are checked for various
features
- additional cleanups in the MAD processing
- update to the srp driver
- creation and use of centralized log message helpers
- add const to a number of args to calls and clean up call chain
- add support for extended cq create verb
- add support for timestamps on cq completion
- add support for processing OPA MAD packets
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (92 commits)
IB/mad: Add final OPA MAD processing
IB/mad: Add partial Intel OPA MAD support
IB/mad: Add partial Intel OPA MAD support
IB/core: Add OPA MAD core capability flag
IB/mad: Add support for additional MAD info to/from drivers
IB/mad: Convert allocations from kmem_cache to kzalloc
IB/core: Add ability for drivers to report an alternate MAD size.
IB/mad: Support alternate Base Versions when creating MADs
IB/mad: Create a generic helper for DR forwarding checks
IB/mad: Create a generic helper for DR SMP Recv processing
IB/mad: Create a generic helper for DR SMP Send processing
IB/mad: Split IB SMI handling from MAD Recv handler
IB/mad cleanup: Generalize processing of MAD data
IB/mad cleanup: Clean up function params -- find_mad_agent
IB/mlx4: Add support for CQ time-stamping
IB/mlx4: Add mmap call to map the hardware clock
IB/core: Pass hardware specific data in query_device
IB/core: Add timestamp_mask and hca_core_clock to query_device
IB/core: Extend ib_uverbs_create_cq
IB/core: Add CQ creation time-stamping flag
...
Pull x86 core updates from Ingo Molnar:
"There were so many changes in the x86/asm, x86/apic and x86/mm topics
in this cycle that the topical separation of -tip broke down somewhat -
so the result is a more traditional architecture pull request,
collected into the 'x86/core' topic.
The topics were still maintained separately as far as possible, so
bisectability and conceptual separation should still be pretty good -
but there were a handful of merge points to avoid excessive
dependencies (and conflicts) that would have been poorly tested in the
end.
The next cycle will hopefully be much more quiet (or at least will
have fewer dependencies).
The main changes in this cycle were:
* x86/apic changes, with related IRQ core changes: (Jiang Liu, Thomas
Gleixner)
- This is the second and most intrusive part of changes to the x86
interrupt handling - full conversion to hierarchical interrupt
domains:
[IOAPIC domain] -----
|
[MSI domain] --------[Remapping domain] ----- [ Vector domain ]
| (optional) |
[HPET MSI domain] ----- |
|
[DMAR domain] -----------------------------
|
[Legacy domain] -----------------------------
This now reflects the actual hardware and allowed us to distangle
the domain specific code from the underlying parent domain, which
can be optional in the case of interrupt remapping. It's a clear
separation of functionality and removes quite some duct tape
constructs which plugged the remap code between ioapic/msi/hpet
and the vector management.
- Intel IOMMU IRQ remapping enhancements, to allow direct interrupt
injection into guests (Feng Wu)
* x86/asm changes:
- Tons of cleanups and small speedups, micro-optimizations. This
is in preparation to move a good chunk of the low level entry
code from assembly to C code (Denys Vlasenko, Andy Lutomirski,
Brian Gerst)
- Moved all system entry related code to a new home under
arch/x86/entry/ (Ingo Molnar)
- Removal of the fragile and ugly CFI dwarf debuginfo annotations.
Conversion to C will reintroduce many of them - but meanwhile
they are only getting in the way, and the upstream kernel does
not rely on them (Ingo Molnar)
- NOP handling refinements. (Borislav Petkov)
* x86/mm changes:
- Big PAT and MTRR rework: making the code more robust and
preparing to phase out exposing direct MTRR interfaces to drivers -
in favor of using PAT driven interfaces (Toshi Kani, Luis R
Rodriguez, Borislav Petkov)
- New ioremap_wt()/set_memory_wt() interfaces to support
Write-Through cached memory mappings. This is especially
important for good performance on NVDIMM hardware (Toshi Kani)
* x86/ras changes:
- Add support for deferred errors on AMD (Aravind Gopalakrishnan)
This is an important RAS feature which adds hardware support for
poisoned data. That means roughly that the hardware marks data
which it has detected as corrupted but wasn't able to correct, as
poisoned data and raises an APIC interrupt to signal that in the
form of a deferred error. It is the OS's responsibility then to
take proper recovery action and thus prolonge system lifetime as
far as possible.
- Add support for Intel "Local MCE"s: upcoming CPUs will support
CPU-local MCE interrupts, as opposed to the traditional system-
wide broadcasted MCE interrupts (Ashok Raj)
- Misc cleanups (Borislav Petkov)
* x86/platform changes:
- Intel Atom SoC updates
... and lots of other cleanups, fixlets and other changes - see the
shortlog and the Git log for details"
* 'x86-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (222 commits)
x86/hpet: Use proper hpet device number for MSI allocation
x86/hpet: Check for irq==0 when allocating hpet MSI interrupts
x86/mm/pat, drivers/infiniband/ipath: Use arch_phys_wc_add() and require PAT disabled
x86/mm/pat, drivers/media/ivtv: Use arch_phys_wc_add() and require PAT disabled
x86/platform/intel/baytrail: Add comments about why we disabled HPET on Baytrail
genirq: Prevent crash in irq_move_irq()
genirq: Enhance irq_data_to_desc() to support hierarchy irqdomain
iommu, x86: Properly handle posted interrupts for IOMMU hotplug
iommu, x86: Provide irq_remapping_cap() interface
iommu, x86: Setup Posted-Interrupts capability for Intel iommu
iommu, x86: Add cap_pi_support() to detect VT-d PI capability
iommu, x86: Avoid migrating VT-d posted interrupts
iommu, x86: Save the mode (posted or remapped) of an IRTE
iommu, x86: Implement irq_set_vcpu_affinity for intel_ir_chip
iommu: dmar: Provide helper to copy shared irte fields
iommu: dmar: Extend struct irte for VT-d Posted-Interrupts
iommu: Add new member capability to struct irq_remap_ops
x86/asm/entry/64: Disentangle error_entry/exit gsbase/ebx/usermode code
x86/asm/entry/32: Shorten __audit_syscall_entry() args preparation
x86/asm/entry/32: Explain reloading of registers after __audit_syscall_entry()
...
Pull scsi target fixes from Nicholas Bellinger:
"Apologies for the late pull request.
Here are the outstanding target-pending fixes for v4.1 code.
The series contains three patches from Sagi + Co that address a few
iser-target issues that have been uncovered during recent testing at
Mellanox.
Patch #1 has a v3.16+ stable tag, and #2-3 have v3.10+ stable tags"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
iser-target: Fix possible use-after-free
iser-target: release stale iser connections
iser-target: Fix variable-length response error completion
We are burrying direct access to MTRR code support on
x86 in order to take advantage of PAT. In the future, we
also want to make the default behaviour of ioremap_nocache()
to use strong UC, use of mtrr_add() on those systems
would make write-combining void.
In order to help both enable us to later make strong
UC default and in order to phase out direct MTRR access
code port the driver over to arch_phys_wc_add() and
annotate that the device driver requires systems to
boot with PAT disabled, with the 'nopat' kernel parameter.
This is a workable compromise given that the ipath device
driver powers the old HTX bus cards that only work in
AMD systems, while the newer IB/qib device driver
powers all PCI-e cards. The ipath device driver is
obsolete, hardware is hard to find and because of this
its a reasonable compromise to require users of ipath
to boot with 'nopat'.
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Doug Ledford <dledford@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andy Walls <awalls@md.metrocast.net>
Cc: Antonino Daplas <adaplas@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Mike Marciniszyn <mike.marciniszyn@intel.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Cc: Roger Pau Monné <roger.pau@citrix.com>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Stefan Bader <stefan.bader@canonical.com>
Cc: Suresh Siddha <sbsiddha@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Ville Syrjälä <syrjala@sci.fi>
Cc: infinipath@intel.com
Cc: jbeulich@suse.com
Cc: konrad.wilk@oracle.com
Cc: linux-rdma@vger.kernel.org
Cc: mchehab@osg.samsung.com
Cc: toshi.kani@hp.com
Link: http://lkml.kernel.org/r/1434053994-2196-4-git-send-email-mcgrof@do-not-panic.com
Link: http://lkml.kernel.org/r/1434356898-25135-5-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch drops unnecessary target_core_fabric_ops parameter usage
for core_tpg_register() during fabric driver TFO->fabric_make_tpg()
se_portal_group creation callback execution.
Instead, use the existing se_wwn->wwn_tf->tf_ops pointer to ensure
fabric driver is really using the same TFO provided at module_init
time.
Also go ahead and drop the forward TFO declarations tree-wide, and
handling the special case for iscsi-target discovery TPG.
Cc: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This is an infrastructure step for querying VF and PF counters.
This code was in the IB driver, move it to the mlx4 core driver
so it will be accessible for more use cases.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As IB VFs are not capable to read the port counters through MADs,
move there to read their own QP counters to gather statistics.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is an infrastructure step to attach all the QPs opened from the
IB driver to a counter in order to collect VF stats from the PF using
those counters.
If the port's type is Ethernet, the counter policy demands two counters
per port (one for RoCE and one for Ethernet). The port default counter
(allocated in mlx4_core) is used for the Ethernet netdev QPs and we
allocate another counter for RoCE.
If the port's traffic is Infiniband, the counter policy demands
one counter per port, so it can use the port's default counter.
Also, Add 'allocated' flag for each counter in order to clean it at
unload.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reserve the last valid counter index for "sink" counter, when a
new counter cannot be allocated, the driver will use this counter.
In order to avoid allocating this counter on any other flow, fix the
indices bitmap allocation range, and reserve the sink counter index.
Add macro for the sink counter index and replace all appearences of the
index with the macro.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For devices which support OPA MADs
1) Use previously defined SMP support functions.
2) Pass correct base version to ib_create_send_mad when processing OPA MADs.
3) Process out_mad_key_index returned by agents for a response. This is
necessary because OPA SMP packets must carry a valid pkey.
4) Carry the correct segment size (OPA vs IBTA) of RMPP messages within
ib_mad_recv_wc.
5) Handle variable length OPA MADs by:
* Adjusting the 'fake' WC for locally routed SMP's to represent the
proper incoming byte_len
* out_mad_size is used from the local HCA agents
1) when sending agent responses on the wire
2) when passing responses through the local_completions
function
NOTE: wc.byte_len includes the GRH length and therefore is different
from the in_mad_size specified to the local HCA agents.
out_mad_size should _not_ include the GRH length as it is added
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add OPA SMP processing functionality.
Define the new OPA SMP format, create support functions for this format using
the previously defined helper functions as appropriate.
These functions are defined in this patch and used in the final OPA MAD support
patch.
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch is the first of 3 which adds processing of OPA MADs
1) Add Intel Omni-Path Architecture defines
2) Increase max management version to accommodate OPA
3) update ib_create_send_mad
If the device supports OPA MADs and the MAD being sent is the OPA base
version alter the MAD size and sg lengths as appropriate
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In order to support alternate sized MADs (and variable sized MADs on OPA
devices) add in/out MAD size parameters to the process_mad core call.
In addition, add an out_mad_pkey_index to communicate the pkey index the driver
wishes the MAD stack to use when sending OPA MAD responses.
The out MAD size and the out MAD PKey index are required by the MAD
stack to generate responses on OPA devices.
Furthermore, the in and out MAD parameters are made generic by specifying them
as ib_mad_hdr rather than ib_mad.
Drivers are modified as needed and are protected by BUG_ON flags if the MAD
sizes passed to them is incorrect.
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch implements allocating alternate receive MAD buffers within the MAD
stack. Support for OPA to send/recv variable sized MADs is implemented later.
1) Convert MAD allocations from kmem_cache to kzalloc
kzalloc is more flexible to support devices with different sized MADs
and research and testing showed that the current use of kmem_cache does
not provide performance benefits over kzalloc.
2) Change struct ib_mad_private to use a flex array for the mad data
3) Allocate ib_mad_private based on the size specified by devices in
rdma_max_mad_size.
4) Carry the allocated size in ib_mad_private to be used when processing
ib_mad_private objects.
5) Alter DMA mappings based on the mad_size of ib_mad_private.
6) Replace the use of sizeof and static defines as appropriate
7) Add appropriate casts for the MAD data when calling processing
functions.
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add max MAD size to the device immutable data set and have all drivers that
support MADs report the current IB MAD size (IB_MGMT_MAD_SIZE) to the core.
Verify MAD size data in both the MAD core and when reading the immutable data.
OPA drivers will report alternate MAD sizes in subsequent patches.
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In preparation to support the new OPA MAD Base version, add a base version
parameter to ib_create_send_mad and set it to IB_MGMT_BASE_VERSION for current
users.
Definition of the new base version and it's processing will occur in later
patches.
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
IB and OPA SMPs share the same processing algorithm but have different header
formats and permissive LID detection.
Add a helper function which is generic to processing the DR forwarding checks which
can be used by both IB and OPA SMP code.
Use this function in the current IB function smi_check_forward_dr_smp.
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
IB and OPA SMPs share the same processing algorithm but have different header
formats and permissive LID detection.
Add a helper function which is generic to processing DR SMP Recv messages which
can be used by both IB and OPA SMP code.
Use this function in the current IB function smi_handle_dr_smp_recv.
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
IB and OPA SMPs share the same processing algorithm but have different header
formats and permissive LID detection.
Add a helper function which is generic to processing DR SMP Send messages which
can be used by both IB and OPA SMP code.
Use this function in the current IB function smi_handle_dr_smp_send.
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Make a helper function to process Directed Route SMPs to be called by the IB
MAD Recv Handler, ib_mad_recv_done_handler.
This cleans up the MAD receive handler code a bit and allows for us to better
share the SMP processing code between IB and OPA SMPs.
IB and OPA SMPs share the same processing algorithm but have different header
formats and permissive LID detection. Therefore this and subsequent patches
split the common processing code from the IB specific code in anticipation of
sharing those algorithms with the OPA code.
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
ib_find_send_mad only needs access to the MAD header not the full IB MAD.
Change the local variable to ib_mad_hdr and change the corresponding cast.
This allows for clean usage of this function with both IB and OPA MADs because
OPA MADs carry the same header as IB MADs.
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
find_mad_agent only needs read only access to the MAD header. Update the
ib_mad pointer to be const ib_mad_hdr. Adjust call tree.
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This includes:
* support allocation of CQ with the TIMESTAMP_COMPLETION creation flag.
* add timestamp_mask and hca_core_clock to query_device, reporting the
number of supported timestamp bits (mask) and the hca_core_clock frequency.
* return hca core clock's offset in query_device vendor's data,
this is needed in order to read the HCA's core clock.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In order to read the HCA's cycle counter efficiently in
user space, we need to map the HCA's register.
This is done through mmap call.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Vendors should be able to pass vendor specific data to/from
user-space via query_device uverb. In order to do this,
we need to pass the vendors' specific udata.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In order to expose timestamp we need to expose two new attributes in
query_device to be used for CQ completion time-stamping:
timestamp_mask - how many bits are valid in the timestamp, where timestamp
values could be 64bits the most.
hca_core_clock - timestamp is given in HW cycles, the frequency in KHZ units
of the HCA, necessary in order to convert cycles to seconds.
This is added both to ib_query_device and its respective uverbs counterpart.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
ib_uverbs_ex_create_cq follows the extension verbs
mechanism. New features (for example, CQ creation flags
field which is added in a downstream patch) could used
via user-space libraries without breaking the ABI.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Currently, ib_create_cq uses cqe and comp_vecotr instead
of the extendible ib_cq_init_attr struct.
Earlier patches already changed the vendors to work with
ib_cq_init_attr. This patch changes the consumers too.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add a new ib_cq_init_attr structure which contains the
previous cqe (minimum number of CQ entries) and comp_vector
(completion vector) in addition to a new flags field.
All vendors' create_cq callbacks are changed in order
to work with the new API.
This commit does not change any functionality.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-By: Devesh Sharma <devesh.sharma@avagotech.com> to patch #2
Signed-off-by: Doug Ledford <dledford@redhat.com>
Previously we configured HW MTU to be netdev->mtu, actually we
need to configure netdev->mtu + (ETH_HLEN + VLAN_HLEN + ETH_FCS_LEN).
Also, query MTU can not fail, hence make the relevant helper a
void functionm, add mlx5e_set_dev_port_mtu, helper function to
handle MTU setting.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle this configuration:
Queues Per Page * SGE BAR2 Queue Register Area Size > Page Size
Use cxgb4_bar2_sge_qregs() to obtain the proper location within the
bar2 region for a given qid.
Rework the DB and GTS write functions to make use of this bar2 info.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
A reorganisation of the PD allocation and deallocation in commit
9ba1377daa ("RDMA/ocrdma: Move PD resource management to driver.")
introduced a double free on pd, as detected by static analysis by
smatch:
drivers/infiniband/hw/ocrdma/ocrdma_verbs.c:682 ocrdma_alloc_pd()
error: double free of 'pd'^
The original call to ocrdma_mbx_dealloc_pd() (which does not kfree
pd) was replaced with a call to _ocrdma_dealloc_pd() (which does
kfree pd). The kfree following this call causes the double free,
so just remove it to fix the problem.
Fixes: 9ba1377daa ("RDMA/ocrdma: Move PD resource management to driver.")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-By: Devesh Sharma <devesh.sharma@avagotech.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This code causes a static checker warning:
drivers/infiniband/hw/usnic/usnic_uiom.c:476 usnic_uiom_alloc_pd()
warn: passing zero to 'PTR_ERR'
This code isn't buggy, but iommu_domain_alloc() doesn't return an error
pointer so we can simplify the error handling and silence the static
checker warning.
The static checker warning is to catch place which do:
if (!ptr)
return ERR_PTR(ptr);
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Dave Goodell <dgoodell@cisco.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Use kernel.h macro definition.
Thanks to Julia Lawall for Coccinelle scripting support.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Registering an event handler is done for a device. This device may have
one RoCE port (no SA cap) and one InfiniBand port (has SA cap).
Therefore, warning from the event handler about a specific port that
doesn't have SA cap is correct but pollutes the kernel log without a
need.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
iser connection termination process happens in 2 stages:
- isert_wait_conn:
- resumes rdma disconnect
- wait for session commands
- wait for flush completions (post a marked wr to signal we are done)
- wait for logout completion
- queue work for connection cleanup (depends on disconnected/timewait
events)
- isert_free_conn
- last reference put on the connection
In case we are terminating during IOs, we might be posting send/recv
requests after we posted the last work request which might lead
to a use-after-free condition in isert_handle_wc.
After we posted the last wr in isert_wait_conn we are guaranteed that
no successful completions will follow (meaning no new work request posts
may happen) but other flush errors might still come. So before we
put the last reference on the connection, we repeat the process of
posting a marked work request (isert_wait4flush) in order to make sure all
pending completions were flushed.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Jenny Falkovich <jennyf@mellanox.com>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
When receiving a new iser connect request we serialize
the pending requests by adding the newly created iser connection
to the np accept list and let the login thread process the connect
request one by one (np_accept_wait).
In case we received a disconnect request before the iser_conn
has begun processing (still linked in np_accept_list) we should
detach it from the list and clean it up and not have the login
thread process a stale connection. We do it only when the connection
state is not already terminating (initiator driven disconnect) as
this might lead us to access np_accept_mutex after the np was released
in live shutdown scenarios.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Jenny Falkovich <jennyf@mellanox.com>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Since commit "2426bd456a6 target: Report correct response ..."
we might get a command with data_size that does not fit to
the number of allocated data sg elements. Given that we rely on
cmd t_data_nents which might be different than the data_size,
we sometimes receive local length error completion. The correct
approach would be to take the command data_size into account when
constructing the ib sg_list.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Jenny Falkovich <jennyf@mellanox.com>
Cc: stable@vger.kernel.org # 3.16+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Ethernet functionality is only available when working in ISSI > 0 mode.
Previously, the IB driver wasn't ready to work on that mode, and hence
building both the IB driver and the Ethernet functionality in the core
driver were disallowed by Kconfigs.
Now, once we have all the pre-steps in place, we can remove this limitation.
The last steps in the IB driver for getting that setup to work are:
create dummy SRQ for the driver's use (until now we could use XRC_SRQ
as SRQ and XRC_SRQ, after moving to ISSI > 0, we separate XRC SRQs from
basic SRQs) and adapt the create QP function to be compatible with ISSI > 0.
Signed-off-by: Haggai Abramovsky <hagaya@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we still don't have RoCE support in mlx5, avoid
creating IB driver instance over Ethernet ports.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ISSI > 0 mode, most of the MAD_IFC command features are deprecated, and can't
be used. Therefore, when in that mode, we replace all of them with other commands
that provide the required functionality.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When working in ISSI > 0 mode, the model exposed by the device for
XRCs and SRQs is different. XRCs use XRC SRQs and plain SRQs are based
on RPM (Receive Memory Pool).
Add helper functions to create, modify, query, and arm XRC SRQs and RMPs.
Signed-off-by: Haggai Abramovsky <hagaya@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ethtool support to get adapter specific hardware statistics
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only include SCSI initiator header files in target code that needs
these header files, namely the SCSI pass-through code and the tcm_loop
driver. Change SCSI_SENSE_BUFFERSIZE into TRANSPORT_SENSE_BUFFER in
target code because the former is intended for initiator code and the
latter for target code. With this patch the only initiator include
directives in target code that remain are as follows:
$ git grep -nHE 'include .scsi/(scsi.h|scsi_host.h|scsi_device.h|scsi_cmnd.h)' drivers/target drivers/infiniband/ulp/{isert,srpt} drivers/usb/gadget/legacy/tcm_*.[ch] drivers/{vhost,xen} include/{target,trace/events/target.h}
drivers/target/loopback/tcm_loop.c:29:#include <scsi/scsi.h>
drivers/target/loopback/tcm_loop.c:31:#include <scsi/scsi_host.h>
drivers/target/loopback/tcm_loop.c:32:#include <scsi/scsi_device.h>
drivers/target/loopback/tcm_loop.c:33:#include <scsi/scsi_cmnd.h>
drivers/target/target_core_pscsi.c:39:#include <scsi/scsi_device.h>
drivers/target/target_core_pscsi.c:40:#include <scsi/scsi_host.h>
drivers/xen/xen-scsiback.c:52:#include <scsi/scsi_host.h> /* SG_ALL */
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
In order to support constant callers of agent_send_response we add const
specifiers to the its pointer arguments.
Adjust the call tree accordingly.
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Hal Rosenstock <hal@mellanox.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The process_mad device function declares some parameters as "in". Make those
parameters const and adjust the call tree under process_mad in the various
drivers accordingly.
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Hal Rosenstock <hal@mellanox.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The unwinding clean up code are err_create_flow starts at the current
index i. That means we shouldn't increment i until we're really sure
we won't have to destroy the current flow; otherwise we might
increment the index, fail inside an is_bonded block, and end up
accessing off the end of the reg_id[] array.
This was detected by Coverity (CID 1271229).
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
If ocrdma_get_pd_num() fails, then we need to free the pd struct we allocated.
This was detected by Coverity (CID 1271245).
Signed-off-by: Roland Dreier <roland@purestorage.com>
Acked-By: Devesh Sharma <devesh.sharma@avagotech.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Avoid that sparse complains about ipoib_neigh_hash_init(). This
patch does not change any functionality. See also patch "IPoIB:
Fix memory leak in the neigh table deletion flow" (commit ID
66172c0993).
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Shlomo Pongratz <shlomop@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
RDMA/nes: Enable the use of the tos field in the nes driver
Signed-off-by: Faisal Latif <Faisal.Latif@intel.com>
Signed-off-by: Tatyana Nikolova <Tatyana.E.Nikolova@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
rdma-cma/iw_cm: Export tos field to iwarp providers
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Tatyana Nikolova <Tatyana.E.Nikolova@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Conflicts:
drivers/net/phy/amd-xgbe-phy.c
drivers/net/wireless/iwlwifi/Kconfig
include/net/mac80211.h
iwlwifi/Kconfig and mac80211.h were both trivial overlapping
changes.
The drivers/net/phy/amd-xgbe-phy.c file got removed in 'net-next' and
the bug fix that happened on the 'net' side is already integrated
into the rest of the amd-xgbe driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull SCSI target fixes from Nicholas Bellinger:
"These are mostly minor fixes, with the exception of the following that
address fall-out from recent v4.1-rc1 changes:
- regression fix related to the big fabric API registration changes
and configfs_depend_item() usage, that required cherry-picking one
of HCH's patches from for-next to address the issue for v4.1 code.
- remaining TCM-USER -v2 related changes to enforce full CDB
passthrough from Andy + Ilias.
Also included is a target_core_pscsi driver fix from Andy that
addresses a long standing issue with a Scsi_Host reference being
leaked on PSCSI device shutdown"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
iser-target: Fix error path in isert_create_pi_ctx()
target: Use a PASSTHROUGH flag instead of transport_types
target: Move passthrough CDB parsing into a common function
target/user: Only support full command pass-through
target/user: Update example code for new ABI requirements
target/pscsi: Don't leak scsi_host if hba is VIRTUAL_HOST
target: Fix se_tpg_tfo->tf_subsys regression + remove tf_subsystem
target: Drop signal_pending checks after interruptible lock acquire
target: Add missing parentheses
target: Fix bidi command handling
target/user: Disallow full passthrough (pass_level=0)
ISCSI: fix minor memory leak
Previously, mlx4_en allocated EQs and used them exclusively.
This affected RoCE performance, as applications which are
events sensitive were limited to use only the legacy EQs.
Change that by introducing an EQ pool. This pool is managed
by mlx4_core. EQs are assigned to ports (when there are limited
number of EQs, multiple ports could be assigned to the same EQs).
An exception to this rule is the ASYNC EQ which handles various events.
Legacy EQs are completely removed as all EQs could be shared.
When a consumer (mlx4_ib/mlx4_en) requests an EQ, it asks for
EQ serving on a specific port. The core driver calculates which
EQ should be assigned to that request.
Because IRQs are shared between IB and Ethernet modules, their
names only include the PCI device BDF address.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In SRIOV, when simple (i.e - Ethernet L2 only) flow steering rules are
created, always create them at MLX4_DOMAIN_NIC priority (instead of
the real priority the function created them at). This is done in order
to let multiple functions add broadcast/multicast rules without
affecting other functions, which is necessary for DPDK in SRIOV.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Detected these variables by building with W=1.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Simplify target core and target drivers by storing the task tag
a.k.a. command identifier inside struct se_cmd.
For several transports (e.g. SRP) tags are 64 bits wide.
Hence add support for 64-bit tags.
(Fix core_tmr_abort_task conversion spec warnings - nab)
(Fix up usb-gadget to use 16-bit tags - HCH + bart)
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: <qla2xxx-upstream@qlogic.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Now that struct se_portal_group contains a protocol identifier field we can
take all the code to format an parse protocol identifiers in CDBs into common
code instead of leaving this to low-level drivers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Now that we store the protocol identifier in the tpg structure we don't
need this method.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Remove the unneeded fabric_ptr argument, and change the type argument
to pass in a SPC protocol identifier.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
By always allocating and adding, respectively removing and freeing
the se_node_acl structure in core code we can remove tons of repeated
code in the init_nodeacl and drop_nodeacl routines. Additionally
this now respects the get_default_queue_depth method in this code
path as well.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
All fabric drivers except for iSCSI always return 1, so implement
that as default behavior.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The first argument of these two functions is always identical
to se_cmd->se_sess. Hence remove the first argument.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: <qla2xxx-upstream@qlogic.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We don't assign pi_ctx to desc->pi_ctx until we're certain to succeed
in the function. That means the cleanup path should use the local
pi_ctx variable, not desc->pi_ctx.
This was detected by Coverity (CID 1260062).
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This is the Ethernet part of the driver for the Mellanox ConnectX(R)-4
Single/Dual-Port Adapter supporting 100Gb/s with VPI. The driver
extends the existing mlx5 driver with Ethernet functionality.
This patch contains the driver entry points but does not include
transmit and receive (see the previous patch in the series) routines.
It also adds the option MLX5_CORE_EN to Kconfig to enable/disable the
Ethernet functionality. Currently, Kconfig is programmed to make
Ethernet and Infiniband functionality mutally exclusive.
Also changed MLX5_INFINIBAND to be depandant on MLX5_CORE instead of
selecting it, since MLX5_CORE could be selected without MLX5_INFINIBAND
being selected.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Query all supported types of dev caps on driver load.
- Store the Cap data outbox per cap type into driver private data.
- Introduce new Macros to access/dump stored caps (using the auto
generated data types).
- Obsolete SW representation of dev caps (no need for SW copy for each
cap).
- Modify IB driver to use new macros for checking caps.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As David Daney pointed in mlx4_core driver [1], mlx5_core is also
misusing the DMA-API.
This patch is removing the code that vmap() memory allocated by
dma_alloc_coherent().
After this patch, users of this drivers might fail allocating resources
on memory fragmeneted systems. This will be fixed later on.
[1] - https://patchwork.ozlabs.org/patch/458531/
CC: David Daney <david.daney@cavium.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most code already uses consts for the struct kernel_param_ops,
sweep the kernel for the last offending stragglers. Other than
include/linux/moduleparam.h and kernel/params.c all other changes
were generated with the following Coccinelle SmPL patch. Merge
conflicts between trees can be handled with Coccinelle.
In the future git could get Coccinelle merge support to deal with
patch --> fail --> grammar --> Coccinelle --> new patch conflicts
automatically for us on patches where the grammar is available and
the patch is of high confidence. Consider this a feature request.
Test compiled on x86_64 against:
* allnoconfig
* allmodconfig
* allyesconfig
@ const_found @
identifier ops;
@@
const struct kernel_param_ops ops = {
};
@ const_not_found depends on !const_found @
identifier ops;
@@
-struct kernel_param_ops ops = {
+const struct kernel_param_ops ops = {
};
Generated-by: Coccinelle SmPL
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Junio C Hamano <gitster@pobox.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: cocci@systeme.lip6.fr
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
As part of enabling single ported VFs over IB ports we need to handle
some of the flows for generting EQ events for VFs which don't come
into play under Eth ports.
This mainly includes port management events derived from changes of the
phyiscal port (lid change, client re-register, down/up, etc), VF pkey table
changes and VF guid changes initiated by the IB driver.
(1) make sure that events are generated only for VFs sitting on
the relevant physical port (under the ALL_SLAVES flow).
(2) before generating the event, convert from physical (one or two)
to VF port (always equals one).
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
When multiplexling a MAD sent from VF, we should convert the port used
by the guest to send the packet to the actual physical port which will be
used to transmit the packet, before building the relevant address-handle (AH).
This is needed under VPI for single ported VFs, since the code that builds
the AH (mlx4_ib_query_ah()) makes decisions based on the input port. If we
use the port number provided by the guest, it might have different protocol
vs. the one this packat has to go from, and hence the result could be wrong.
So far, the conversion was done after the AH was built and it worked for
single ported Eth VFs which were not enabled under VPI. When adding support
for single ported IB VFs and VPI, we hit that.
Fixes: 449fc48866 ('net/mlx4: Adapt code for N-Port VF')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support for using UD and AF_IB is currently broken. The
IB_CM_SIDR_REQ_RECEIVED message is not handled properly in
cma_save_net_info() and we end up falling into code that will try and
process the request as ipv4/ipv6, which will end up failing.
The resolution is to add a check for the SIDR_REQ and call
cma_save_ib_info() with a NULL path record. Change cma_save_ib_info()
to copy the src sib info from the listen_id when the path record is NULL.
Reported-by: Hari Shankar <Hari.Shankar@netapp.com>
Signed-off-by: Matt Finlay <matt@mellanox.com>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
After discussion upstream, it was agreed to transition the usage of iboe
in the kernel to roce. This keeps our terminology consistent with what
was finalized in the IBTA Annex 16 and IBTA Annex 17 publications.
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Problem reported by: Ted Kim <ted.h.kim@oracle.com>:
We have a case where a Linux system and a non-Linux system are
trying to interoperate. The Linux host is the active side and
starts the connection establishment, but later decides to not go
through with the connection setup and does rdma_destroy_id().
The rdma_destroy_id() eventually works its way down to cm_destroy_id()
in core/cm.c, where a REJ is sent. The non-Linux system
has some trouble recognizing the REJ because of:
A. CM states which can't receive the REJ
B. Some issues about REJ formatting (missing comm ID)
ISSUE A: That part of the spec says, a Consumer Reject REJ can be
sent for a connection abort, but it goes further
and says: can send a REJ message with a "Consumer Reject"
Reason code if they are in a CM state (i.e. REP
Rcvd, MRA(REP) Sent, REQ Rcvd, MRA Sent) that allows
a REJ to be sent (lines 35-38).
Of the states listed there in that sentence, it would
seem to limit the active side to using the Consumer Reject
(for the abort case) in just the REP-Rcvd and MRA-REP-Sent
states. That is basically only after the active side
sees a REP (or alternatively goes down the state transitions
to timeout in which case a Timeout REJ is sent).
As a fix, in cm-destroy-id() move the IB-CM-MRA-REQ-RCVD case
to the same as REQ-SENT. Essentially, make a REJ sent after
getting an MRA on active side a timeout rather than Consumer-
Reject, which is arguably more correct with the CM state
diagrams previous to getting a REP.
Signed-off-by: Ted Kim <ted.h.kim@oracle.com>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
As of commit 5eb620c81c "IB/core: Add helpers for uncached GID and P_Key
searches"; pkey_tbl_len and gid_tbl_len are immutable data which are stored in
the ib_device.
The per port core capability flags to be added later are also immutable data to
be stored in the ib_device object.
In preparation for this create a structure for per port immutable data and
place the pkey and gid table lengths within this structure.
"get_port_immutable" is added as a mandatory device function to allow the
drivers to fill in this data.
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The addition of the rdma_cap_ib_mad is technically broken in ib_umad_remove_one
because the loop "i" value is not a port value.
This bug resulted in the ib_umad failing to properly remove its resources when
the core capability functions were converted to bit fields.
NOTE: e17371d73908 did not result in broken behavior on its own. It was only
an issue when the implementation of rdma_cap_ib_mad was changed.
Pass the port value to rdma_cap_ib_mad.
Fixes: e17371d73908 ("IB/Verbs: Use management helper rdma_cap_ib_mad()")
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Use the new common rdma_[start|end]_port functions instead of using
local variables and figuring it out on the fly.
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The following functions only need read access to the data passed to them.
ib_mad_kernel_rmpp_agent
is_rmpp_data_mad
rcv_has_same_gid
ib_find_send_mad
Clarify with const specifiers
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
rcv_has_same_class only needs access to the MAD header
specify WR and Receive WC as const
Reviewed-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
ib_response_mad only needs read access to the MAD header, not write access
to the entire mad struct, so replace struct ib_mad with const struct
ib_mad_hdr
Reviewed-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
validate_mad only needs read access to the MAD header, not write access
to the entire mad struct, so replace struct ib_mad with const struct
ib_mad_hdr
Reviewed-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Some of us keep revisiting the code to decode enumerations that
appear in out logs. Let's borrow the nice logging helpers that
exists in xprtrdma and rds for CMA events, IB events and WC statuses.
Reviewd-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The SCSI standard defines 64-bit values for LUNs. Large arrays
employing large or hierarchical LUN numbers become more and more
common. So update the SRP initiator to use 64-bit LUN numbers.
See also Hannes Reinecke, commit 9cb78c16f5 ("scsi: use 64-bit LUNs"),
June 2014.
The largest LUN number that has been tested is 0xd2003fff00000000.
Checked the following structure sizes with gdb:
* sizeof(struct srp_cmd) = 48
* sizeof(struct srp_tsk_mgmt) = 48
* sizeof(struct srp_aer_req) = 36
The ibmvscsi changes have been compile tested only (on a PPC system).
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Yann Droneaud <ydroneaud@opteya.com>
Cc: Sebastian Parschauer <sebastian.riemer@profitbricks.com>
Cc: Brian King <brking@linux.vnet.ibm.com>
Cc: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Cc: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Remove the !ch->target tests from the reconnect code. These
tests are not needed: upon entry of srp_rport_reconnect()
it is guaranteed that all ch->target pointers are non-NULL.
None of the functions srp_new_cm_id(), srp_finish_req(),
srp_create_ch_ib() nor srp_connect_ch() modifies this pointer.
srp_free_ch_ib() is never called concurrently with
srp_rport_reconnect().
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Sebastian Parschauer <sebastian.riemer@profitbricks.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The function srp_free_req_data() does not use ch->target.
Hence remove the ch->target != NULL check.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Sebastian Parschauer <sebastian.riemer@profitbricks.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Move the module version and release date into separate fields.
This makes the modinfo output easier to read.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Sebastian Parschauer <sebastian.riemer@profitbricks.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
A long time ago the data type int64_t was declared as long long
on x86 systems and as long on PPC systems. Today that data type
is declared as long long on all Linux architectures. This means
that the casts from uint64_t into unsigned long long are
superfluous. Remove these superfluous casts.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Sebastian Parschauer <sebastian.riemer@profitbricks.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Although it is possible to let SRP I/O continue if a reconnect
results in a reduction of the number of channels, the current
code does not handle this scenario correctly. Instead of making
the reconnect code more complex, consider this as a reconnection
failure.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Sebastian Parschauer <sebastian.riemer@profitbricks.com>
Cc: <stable@vger.kernel.org> #v3.19
Signed-off-by: Doug Ledford <dledford@redhat.com>
Reception of a DREQ message only causes the state of a single
channel to change. Hence move the 'connected' member variable
from the target to the channel data structure. This patch
avoids that following false positive warning can be reported
by srp_destroy_qp():
WARNING: at drivers/infiniband/ulp/srp/ib_srp.c:617 srp_destroy_qp+0xa6/0x120 [ib_srp]()
Call Trace:
[<ffffffff8106e10f>] warn_slowpath_common+0x7f/0xc0
[<ffffffff8106e16a>] warn_slowpath_null+0x1a/0x20
[<ffffffffa0440226>] srp_destroy_qp+0xa6/0x120 [ib_srp]
[<ffffffffa0440322>] srp_free_ch_ib+0x82/0x1e0 [ib_srp]
[<ffffffffa044408b>] srp_create_target+0x7ab/0x998 [ib_srp]
[<ffffffff81346f60>] dev_attr_store+0x20/0x30
[<ffffffff811dd90f>] sysfs_write_file+0xef/0x170
[<ffffffff8116d248>] vfs_write+0xc8/0x190
[<ffffffff8116d411>] sys_write+0x51/0x90
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Sebastian Parschauer <sebastian.riemer@profitbricks.com>
Cc: <stable@vger.kernel.org> #v3.19
Signed-off-by: Doug Ledford <dledford@redhat.com>
Avoid that receiving a DREQ while RDMA channels are being
established causes target->qp_in_error to be reset.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Sebastian Parschauer <sebastian.riemer@profitbricks.com>
Cc: <stable@vger.kernel.org> #v3.19
Signed-off-by: Doug Ledford <dledford@redhat.com>
Fix a scsi_get_host() / scsi_host_put() imbalance in the error
path of srp_create_target(). See also patch "IB/srp: Avoid that
I/O hangs due to a cable pull during LUN scanning" (commit ID
34aa654ecb).
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Sebastian Parschauer <sebastian.riemer@profitbricks.com>
Cc: <stable@vger.kernel.org> #v3.19
Signed-off-by: Doug Ledford <dledford@redhat.com>
Return values of 0 do not make sense for functions which return enum
smi_action
Reviewed-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
is_rmpp_data_mad is more descriptive for this function.
Reviewed-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Previously start_port and end_port were defined in 2 places, cache.c and
device.c and this prevented their use in other modules.
Make these common functions, change the name to reflect the rdma
name space, and update existing users.
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Introduce helper rdma_cap_eth_ah() to help us check if the port of an
IB device support Ethernet Address Handler.
Signed-off-by: Michael Wang <yun.wang@profitbricks.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Tested-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Introduce helper rdma_cap_af_ib() to help us check if the port of an
IB device support Native Infiniband Address.
Signed-off-by: Michael Wang <yun.wang@profitbricks.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Tested-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Introduce helper rdma_cap_ib_mcast() to help us check if the port of an
IB device support Infiniband Multicast.
Signed-off-by: Michael Wang <yun.wang@profitbricks.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Tested-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Introduce helper rdma_cap_ib_sa() to help us check if the port of an
IB device support Infiniband Subnet Administration.
Signed-off-by: Michael Wang <yun.wang@profitbricks.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Tested-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Introduce helper rdma_cap_iw_cm() to help us check if the port of an
IB device support IWARP Communication Manager.
Signed-off-by: Michael Wang <yun.wang@profitbricks.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Tested-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Introduce helper rdma_cap_ib_cm() to help us check if the port of an
IB device support Infiniband Communication Manager.
Signed-off-by: Michael Wang <yun.wang@profitbricks.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Tested-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Introduce helper rdma_cap_ib_smi() to help us check if the port of an
IB device support Infiniband Subnet Management Interface.
Signed-off-by: Michael Wang <yun.wang@profitbricks.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Tested-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Introduce helper rdma_cap_ib_mad() to help us check if the port of an
IB device support Infiniband Management Datagrams.
Signed-off-by: Michael Wang <yun.wang@profitbricks.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Tested-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Use raw management helpers to reform rest part in IB-core cma.
Signed-off-by: Michael Wang <yun.wang@profitbricks.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Tested-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Reform cma_acquire_dev() with management helpers, introduce
cma_validate_port() to make the code more clean.
Signed-off-by: Michael Wang <yun.wang@profitbricks.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Tested-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Use raw management helpers to reform mcast related part in IB-core cma.
Signed-off-by: Michael Wang <yun.wang@profitbricks.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Tested-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Use raw management helpers to reform route related part in IB-core cma.
Signed-off-by: Michael Wang <yun.wang@profitbricks.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Tested-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Use raw management helpers to reform cm related part in IB-core cma/ucm.
Few checks focus on the device cm type rather than the port capability,
directly pass port 1 works currently, but can't support mixing cm type
device in future.
Signed-off-by: Michael Wang <yun.wang@profitbricks.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Tested-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Use raw management helpers to reform IB-core verbs
Signed-off-by: Michael Wang <yun.wang@profitbricks.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Tested-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Use raw management helpers to reform IB-ulp ipoib.
Signed-off-by: Michael Wang <yun.wang@profitbricks.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Tested-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Use raw management helpers to reform IB-core multicast.
Signed-off-by: Michael Wang <yun.wang@profitbricks.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Tested-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Use raw management helpers to reform IB-core sa_query.
Signed-off-by: Michael Wang <yun.wang@profitbricks.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Tested-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Use raw management helpers to reform IB-core cm.
Signed-off-by: Michael Wang <yun.wang@profitbricks.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Tested-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Use raw management helpers to reform IB-core mad/agent/user_mad.
Signed-off-by: Michael Wang <yun.wang@profitbricks.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Tested-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
HW currently restricts the IB MTU range between 512 and 4096.
Fail connection for MTUs lesser than 512.
Signed-off-by: Naga Irrinki <naga.irrinki@avagotech.com>
Signed-off-by: Selvin Xavier <selvin.xavier@avagotech.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
rdma_addr_find_dmac_by_grh fails to resolve dmac for link local address.
Use rdma_get_ll_mac to resolve the link local address.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@avagotech.com>
Signed-off-by: Mitesh Ahuja <mitesh.ahuja@avagotech.com>
Signed-off-by: Devesh Sharma <devesh.sharma@avagotech.com>
Signed-off-by: Selvin Xavier <selvin.xavier@avagotech.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
If DPP PDs are not supported by the FW, allocate only normal PDs.
Signed-off-by: Mitesh Ahuja <mitesh.ahuja@avagotech.com>
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@avagotech.com>
Signed-off-by: Selvin Xavier <selvin.xavier@avagotech.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
If the adapter ports are in PFC mode and VLAN is not configured,
use vlan tag 0 for RoCE traffic. Also, log an advisory message
in system logs.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@avagotech.com>
Signed-off-by: Devesh Sharma <devesh.sharma@avagotech.com>
Signed-off-by: Selvin Xavier <selvin.xavier@avagotech.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Don't move QP to error state, if QP is in reset state during QP
destroy operation.
Signed-off-by: Devesh Sharma <devesh.sharma@avagotech.com>
Signed-off-by: Selvin Xavier <selvin.xavier@avagotech.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Changing the destroy sequence of mailbox queue and event queues.
FW expects mailbox queue to be destroyed before desroying the EQs.
Signed-off-by: Selvin Xavier <selvin.xavier@avagotech.com>
Signed-off-by: Devesh Sharma <devesh.sharma@avagotech.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
These KERN_<LEVEL> uses are unnecessary with pr_<level> and cause
bad logging output so remove them.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Commit d4988623cc ("IB/qib: use arch_phys_wc_add()")
adjusted mtrr inititialization to use the new interface.
Unfortunately, the new interface returns a signed
value and the patch tested the unsigned wc_cookie.
Fix the issue by changing the type of wc_cookie to int. For
the success case the ret left at zero to avoid
a warning from the caller. For failure wc_cookie
is used as the ret.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The string iwpm_ulib_name is recorded in a nlmsg as a netlink attribute.
Without this fix parsing of the nlmsg by the userspace port mapper service fails
because of unknown attribute length, causing the port mapper service not to
register the client, which has sent the nlmsg.
Signed-off-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Cc: <stable@vger.kernel.org> #v3.16
Reviewed-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
For listening endpoints bound to the wildcard address, we need to pass
the wildcard address mapping to iwpm_get_remote_info() instead of the
mapped address of the new child connection.
Without this fix, and with iwarp port mapping enabled, each iw_cxgb4
connection that is spawned from a listening endpoint bound to the wildcard
address, will generate an annoying dmesg entry about failing to find
the remote address mapping info, and the connection state displayed in
debugfs under /sys/kernel/debug/iw_cxgb4/<pci-slot-no>/eps will not have
the peer's address/port mapping info. The connection still works though.
Fixes: 5b6b8fe ("RDMA/cxgb4: Report the actual address of the remote connecting peer")
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Reviewed-by: Tatyana Nikolova <Tatyana.E.Nikolova@intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Using an element of a struct as the address for the memcpy of the whole
struct may introduce a buffer overflow and does not help readability either
simply pass the real thing as first argument to memcpy.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
See also patch "IPoIB/cm: Add connected mode support for devices
without SRQs" (commit ID 68e995a295). Detected by smatch.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Pradeep Satyanarayana <pradeeps@linux.vnet.ibm.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Remove these log messages in favor of per-endpoint counters as well as
device-global counters that can be inspected via debugfs.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Addresses the following kernel logs seen during boot of sparc systems:
Kernel unaligned access at TPC[103bce50] cm_find_listen+0x34/0xf8 [ib_cm]
Kernel unaligned access at TPC[103bce50] cm_find_listen+0x34/0xf8 [ib_cm]
Kernel unaligned access at TPC[103bce50] cm_find_listen+0x34/0xf8 [ib_cm]
Kernel unaligned access at TPC[103bce50] cm_find_listen+0x34/0xf8 [ib_cm]
Kernel unaligned access at TPC[103bce50] cm_find_listen+0x34/0xf8 [ib_cm]
Signed-off-by: David Ahern <david.ahern@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This driver already makes use of ioremap_wc() on PIO buffers,
so convert it to use arch_phys_wc_add().
The qib driver uses a mmap() special case for when PAT is
not used, this behaviour used to be determined with a
module parameter but since we have been asked to just
remove that module parameter this checks for the WC cookie,
if not set we can assume PAT was used. If its set we do
what we used to do for the mmap for when MTRR was enabled.
The removal of the module parameter is OK given that Andy
notes that even if users of module parameter are still around
it will not prevent loading of the module on recent kernels.
Cc: Doug Ledford <dledford@redhat.com>
Cc: Toshi Kani <toshi.kani@hp.com>
Cc: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Cc: Mike Marciniszyn <mike.marciniszyn@intel.com>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: Dennis Dalessandro <dennis.dalessandro@intel.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Suresh Siddha <sbsiddha@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Juergen Gross <jgross@suse.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Antonino Daplas <adaplas@gmail.com>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Stefan Bader <stefan.bader@canonical.com>
Cc: konrad.wilk@oracle.com
Cc: ville.syrjala@linux.intel.com
Cc: david.vrabel@citrix.com
Cc: jbeulich@suse.com
Cc: Roger Pau Monné <roger.pau@citrix.com>
Cc: infinipath@intel.com
Cc: linux-rdma@vger.kernel.org
Cc: linux-fbdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: xen-devel@lists.xensource.com
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
There is no good reason not to, we eventually delete it as well.
Cc: Toshi Kani <toshi.kani@hp.com>
Cc: Suresh Siddha <sbsiddha@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Juergen Gross <jgross@suse.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Antonino Daplas <adaplas@gmail.com>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Mike Marciniszyn <infinipath@intel.com>
Cc: Roland Dreier <roland@kernel.org>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: linux-rdma@vger.kernel.org
Cc: linux-fbdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
While unmapping an ODP writable page, the dirty bit of the page is set. In
order to do so, the head of the compound page is found.
Currently, the compound head is found even on non-writable pages, where it is
never used, leading to unnecessary cpu barrier that impacts performance.
This patch moves the search for the compound head to be done only when needed.
Signed-off-by: Guy Shapiro <guysh@mellanox.com>
Acked-by: Shachar Raindel <raindel@mellanox.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Currently, while mapping or unmapping pages for ODP, the umem mutex is locked
and unlocked once for each page. Such lock/unlock operation take few tens to
hundreds of nsecs. This makes a significant impact when mapping or unmapping few
MBs of memory.
To avoid this, the mutex should be locked only once per operation, and not per
page.
Signed-off-by: Guy Shapiro <guysh@mellanox.com>
Acked-by: Shachar Raindel <raindel@mellanox.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Get the actual (non-mapped) ip/tcp address of the connecting peer from
the port mapper
Also setup the passive side endpoint to correctly display the actual
and mapped addresses for the new connection.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Get the actual (non-mapped) ip/tcp address of the connecting peer from
the port mapper and report the address info to the user space application
at the time of connection establishment
Signed-off-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add functionality to enable the port mapper on the passive side to provide to its
clients the actual (non-mapped) ip/tcp address information of the connecting peer
1) Adding remote_info_cb() to process the address info of the connecting peer
The address info is provided by the user space port mapper service when
the connection is initiated by the peer
2) Adding a hash list to store the remote address info
3) Adding functionality to add/remove the remote address info
After the info has been provided to the port mapper client,
it is removed from the hash list
Signed-off-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Currently the iw_cxgb4 implementation requires the qp and cq qid densities
to match as well as the qp and cq id ranges. So fail a device open if
the device configuration doesn't meet the requirements.
The reason for these restictions has to do with the fact that IQ qid X
has a UGTS register in the same bar2 page as EQ qid X. Thus both qids
need to be allocated to the same user process for security reasons.
The logic that does this (the qpid allocator in iw_cxgb4/resource.c)
handles this but requires the above restrictions.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
For T5, we must not use the kdb/kgts registers, in order avoid db drops
under extreme loads.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
- get_dma_mr() was using ~0UL which is should be ~0ULL. This causes the
DMA MR to get setup incorrectly in hardware.
- wr_log_show() needed a 64b divide function div64_u64() instead of
doing
division directly.
- fixed warnings about recasting a pointer to a u64
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When accepting a new IPv4 connect to an IPv6 socket, the CMA tries to
canonize the address family to IPv4, but does not properly process
the listening sockaddr to get the listening port, and does not properly
set the address family of the canonized sockaddr.
Fixes: e51060f08a ("IB: IP address based RDMA connection manager")
Cc: <stable@vger.kernel.org>
Reported-By: Yotam Kenneth <yotamke@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Pull fourth vfs update from Al Viro:
"d_inode() annotations from David Howells (sat in for-next since before
the beginning of merge window) + four assorted fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
RCU pathwalk breakage when running into a symlink overmounting something
fix I_DIO_WAKEUP definition
direct-io: only inc/dec inode->i_dio_count for file systems
fs/9p: fix readdir()
VFS: assorted d_backing_inode() annotations
VFS: fs/inode.c helpers: d_inode() annotations
VFS: fs/cachefiles: d_backing_inode() annotations
VFS: fs library helpers: d_inode() annotations
VFS: assorted weird filesystems: d_inode() annotations
VFS: normal filesystems (and lustre): d_inode() annotations
VFS: security/: d_inode() annotations
VFS: security/: d_backing_inode() annotations
VFS: net/: d_inode() annotations
VFS: net/unix: d_backing_inode() annotations
VFS: kernel/: d_inode() annotations
VFS: audit: d_backing_inode() annotations
VFS: Fix up some ->d_inode accesses in the chelsio driver
VFS: Cachefiles should perform fs modifications on the top layer only
VFS: AF_UNIX sockets should call mknod on the top layer only
Moni Shoua