Due to erratum #582743, the Marvell Armada-AP806 can't access 64bit to
ARM SMMUv2 registers.
Provide implementation relevant hooks:
- split the writeq/readq to two accesses of writel/readl.
- mask the MMU_IDR2.PTFSv8 fields to not use AArch64 format (but
only AARCH32_L) since with AArch64 format 32 bits access is not supported.
Note that most 64-bit registers like TTBRn can be accessed as two 32-bit
halves without issue, and AArch32 format ensures that the register writes
which must be atomic (for TLBI etc.) need only be 32-bit.
Signed-off-by: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/20200715070649.18733-3-tn@semihalf.com
Signed-off-by: Will Deacon <will@kernel.org>
'cfg_probe' hook is called at the very end of configuration probing
procedure and therefore features override and workaround may become
complex like for ID register fixups. In preparation for adding Marvell
errata move 'cfg_probe' a bit earlier to have chance to adjust
the detected features before we start consuming them.
Since the Cavium quirk (the only user) does not alter features
it is safe to do so.
Suggested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/20200715070649.18733-2-tn@semihalf.com
Signed-off-by: Will Deacon <will@kernel.org>
Quite some non OF/ACPI users of irqdomains allocate firmware nodes of type
IRQCHIP_FWNODE_NAMED or IRQCHIP_FWNODE_NAMED_ID and free them right after
creating the irqdomain. The only purpose of these FW nodes is to convey
name information. When this was introduced the core code did not store the
pointer to the node in the irqdomain. A recent change stored the firmware
node pointer in irqdomain for other reasons and missed to notice that the
usage sites which do the alloc_fwnode/create_domain/free_fwnode sequence
are broken by this. Storing a dangling pointer is dangerous itself, but in
case that the domain is destroyed later on this leads to a double free.
Remove the freeing of the firmware node after creating the irqdomain from
all affected call sites to cure this.
Fixes: 711419e504 ("irqdomain: Add the missing assignment of domain->fwnode for named fwnode")
Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/873661qakd.fsf@nanos.tec.linutronix.de
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Link: https://lore.kernel.org/r/20200708210434.22518-1-grandmaster@al2klimov.de
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The MMU_CTRL register of MT8173 is different from other SoCs.
The in_order_wr_en is bit[9] which is zero by default.
Other SoCs have the vitcim_tlb_en feature mapped to bit[12].
This bit is set to one by default. We need to preserve the bit
when setting F_MMU_TF_PROT_TO_PROGRAM_ADDR as otherwise the
bit will be cleared and IOMMU performance will drop.
Signed-off-by: Chao Hao <chao.hao@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Yong Wu <yong.wu@mediatek.com>
Link: https://lore.kernel.org/r/20200703044127.27438-10-chao.hao@mediatek.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Starting with mt6779, iommu needs to extend to 256 bytes from 128
bytes which can send the max number of data for memory protection
pa alignment. So we can use a separate patch to modify it.
Signed-off-by: Chao Hao <chao.hao@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/20200703044127.27438-9-chao.hao@mediatek.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Some platforms(ex: mt6779) need to improve performance by setting
REG_MMU_WR_LEN_CTRL register. And we can use WR_THROT_EN macro to control
whether we need to set the register. If the register uses default value,
iommu will send command to EMI without restriction, when the number of
commands become more and more, it will drop the EMI performance. So when
more than ten_commands(default value) don't be handled for EMI, iommu will
stop send command to EMI for keeping EMI's performace by enabling write
throttling mechanism(bit[5][21]=0) in MMU_WR_LEN_CTRL register.
Signed-off-by: Chao Hao <chao.hao@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/20200703044127.27438-8-chao.hao@mediatek.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The max larb number that a iommu HW support is 8(larb0~larb7 in the below
diagram).
If the larb's number is over 8, we use a sub_common for merging
several larbs into one larb. At this case, we will extend larb_id:
bit[11:9] means common-id;
bit[8:7] means subcommon-id;
>From these two variables, we could get the real larb number when
translation fault happen.
The diagram is as below:
EMI
|
IOMMU
|
-----------------
| |
common1 common0
| |
-----------------
|
smi common
|
------------------------------------
| | | | | |
3'd0 3'd1 3'd2 3'd3 ... 3'd7 <-common_id(max is 8)
| | | | | |
Larb0 Larb1 | Larb3 ... Larb7
|
smi sub common
|
--------------------------
| | | |
2'd0 2'd1 2'd2 2'd3 <-sub_common_id(max is 4)
| | | |
Larb8 Larb9 Larb10 Larb11
In this patch we extend larb_remap[] to larb_remap[8][4] for this.
larb_remap[x][y]: x means common-id above, y means subcommon_id above.
We can also distinguish if the M4U HW has sub_common by HAS_SUB_COMM
macro.
Signed-off-by: Chao Hao <chao.hao@mediatek.com>
Reviewed-by: Yong Wu <yong.wu@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/20200703044127.27438-7-chao.hao@mediatek.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
For mt6779, MMU_INV_SEL register's offset is changed from
0x38 to 0x2c, so we can put inv_sel_reg in the plat_data to
use it.
In addition, we renamed it to REG_MMU_INV_SEL_GEN1 and use it
before mt6779.
Signed-off-by: Chao Hao <chao.hao@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Yong Wu <yong.wu@mediatek.com>
Link: https://lore.kernel.org/r/20200703044127.27438-6-chao.hao@mediatek.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Add F_MMU_IN_ORDER_WR_EN_MASK and F_MMU_STANDARD_AXI_MODE_EN_MASK
definitions in MISC_CTRL register.
F_MMU_STANDARD_AXI_MODE_EN_MASK:
If we set F_MMU_STANDARD_AXI_MODE_EN_MASK (bit[3][19] = 0, not follow
standard AXI protocol), the iommu will priorize sending of urgent read
command over a normal read command. This improves the performance.
F_MMU_IN_ORDER_WR_EN_MASK:
If we set F_MMU_IN_ORDER_WR_EN_MASK (bit[1][17] = 0, out-of-order write),
the iommu will re-order write commands and send the write commands with
higher priority. Otherwise the sending of write commands will be done in
order. The feature is controlled by OUT_ORDER_WR_EN platform data flag.
Suggested-by: Yong Wu <yong.wu@mediatek.com>
Signed-off-by: Chao Hao <chao.hao@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/20200703044127.27438-5-chao.hao@mediatek.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Given the fact that we are adding more and more plat_data bool values,
it would make sense to use a u32 flags register and add the appropriate
macro definitions to set and check for a flag present.
No functional change.
Suggested-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Chao Hao <chao.hao@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Yong Wu <yong.wu@mediatek.com>
Link: https://lore.kernel.org/r/20200703044127.27438-4-chao.hao@mediatek.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
For iommu offset=0x48 register, only the previous mt8173/mt8183 use the
name STANDARD_AXI_MODE, all the latest SoC extend the register more
feature by different bits, for example: axi_mode, in_order_en, coherent_en
and so on. So rename REG_MMU_MISC_CTRL may be more proper.
This patch only rename the register name, no functional change.
Signed-off-by: Chao Hao <chao.hao@mediatek.com>
Reviewed-by: Yong Wu <yong.wu@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/20200703044127.27438-3-chao.hao@mediatek.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This driver shouldn't need anything architecture-specific (that isn't
under CONFIG_ARM protection already), and has already been accessible
from certain x86 configurations by virtue of the previously-cleaned-up
"ARM || IOMMU_DMA" dependency. Allow COMPILE_TEST for all architectures.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/1fe2006aa98f008a2e689adba6e8c96e9197f903.1593791968.git.robin.murphy@arm.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Wacky COMPILE_TEST dependencies based on who used to define
dev_archdata.iommu can go.
Dependencies on ARM or ARM64 already implied by the ARCH_* platform
selection can go.
The entire IOMMU_SUPPORT menu already depends on MMU, so those can go.
IOMMU_DMA is for the architecture's DMA API implementation to choose,
and its interface to IOMMU drivers is properly stubbed out if disabled,
so dependencies on or selections of that can go (AMD_IOMMU is the
current exception since the x86 drivers have to provide their own entire
dma_map_ops implementation).
Since commit ed6ccf10f2 ("dma-mapping: properly stub out the DMA API
for !CONFIG_HAS_DMA"), drivers which simply use the dma-mapping API
should not need to depend on HAS_DMA, so those can go.
And a long-dead option for code removed from the MSM driver 4 years ago
can also go.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/7fb9c74dc6bd12a4619ca44c92408e91352f1be0.1593791968.git.robin.murphy@arm.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
When CONFIG_OF=n of_match_device() gets pre-processed out of existence
leaving qcom-smmu_client_of_match unused. Mark it as possibly unused to
keep the compiler from warning in that case.
Fixes: 0e764a0101 ("iommu/arm-smmu: Allow client devices to select direct mapping")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20200604203905.31964-1-jcrouse@codeaurora.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Use the qcom implementation for IOMMU hardware on sm8150 and sm8250 SoCs.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200609194030.17756-3-jonathan@marek.ca
Signed-off-by: Will Deacon <will@kernel.org>
The IOMMU_SYS_CACHE_ONLY flag was never exposed via the DMA API and
has no in-tree users. Remove it.
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: "Isaac J. Manjarres" <isaacm@codeaurora.org>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Rob Clark <robdclark@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Signed-off-by: Will Deacon <will@kernel.org>
At least the version in the header file to fix a compile warning about
the function being unused.
Reported-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Link: https://lore.kernel.org/r/20200630124611.23153-1-joro@8bytes.org
If NO_DMA=y (e.g. Sun-3 all{mod,yes}-config):
drivers/iommu/dma-iommu.o: In function `iommu_dma_mmap':
dma-iommu.c:(.text+0x92e): undefined reference to `dma_pgprot'
IOMMU_DMA must not be selected, unless HAS_DMA=y.
Hence fix this by making SUN50I_IOMMU depend on HAS_DMA.
Fixes: 4100b8c229 ("iommu: Add Allwinner H6 IOMMU driver")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20200629121146.24011-1-geert@linux-m68k.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The pte_dma variable in the unmap callback is set but never used. Remove
it.
Fixes: 4100b8c229 ("iommu: Add Allwinner H6 IOMMU driver")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20200628180844.79205-2-maxime@cerno.tech
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The flush_all_tlb call back can be called from an atomic context, so using
readl_poll_timeout that embeds a udelay doesn't work.
Fixes: 4100b8c229 ("iommu: Add Allwinner H6 IOMMU driver")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20200628180844.79205-1-maxime@cerno.tech
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The iommu private pointer is already used in the Mediatek IOMMU v1
driver, so move the dma_iommu_mapping pointer into 'struct
mtk_iommu_data' and do not use dev->archdata.iommu anymore.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Link: https://lore.kernel.org/r/20200625130836.1916-9-joro@8bytes.org
Remove the use of dev->archdata.iommu_domain and use the private
per-device pointer provided by IOMMU core code instead.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Link: https://lore.kernel.org/r/20200625130836.1916-8-joro@8bytes.org
Remove the use of dev->archdata.iommu and use the private per-device
pointer provided by IOMMU core code instead.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Link: https://lore.kernel.org/r/20200625130836.1916-7-joro@8bytes.org
Remove the use of dev->archdata.iommu and use the private per-device
pointer provided by IOMMU core code instead.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Link: https://lore.kernel.org/r/20200625130836.1916-6-joro@8bytes.org
Remove the use of dev->archdata.iommu and use the private per-device
pointer provided by IOMMU core code instead.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Link: https://lore.kernel.org/r/20200625130836.1916-5-joro@8bytes.org
Remove the use of dev->archdata.iommu and use the private per-device
pointer provided by IOMMU core code instead.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Link: https://lore.kernel.org/r/20200625130836.1916-4-joro@8bytes.org
Remove the use of dev->archdata.iommu and use the private per-device
pointer provided by IOMMU core code instead.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20200625130836.1916-3-joro@8bytes.org
Remove the use of dev->archdata.iommu and use the private per-device
pointer provided by IOMMU core code instead.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200625130836.1916-2-joro@8bytes.org
Do not call atomic64_set() directly to update the domain page-table
root and use two new helper functions.
This makes it easier to implement additional work necessary when
the page-table is updated.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Link: https://lore.kernel.org/r/20200626080547.24865-2-joro@8bytes.org
Currently, Linux logs the two messages below.
[ 0.979142] pci 0000:00:00.2: AMD-Vi: Extended features (0xf77ef22294ada):
[ 0.979546] PPR NX GT IA GA PC GA_vAPIC
The log level of these lines differs though. The first one has level
*info*, while the second has level *warn*, which is confusing.
$ dmesg -T --level=info | grep "Extended features"
[Tue Jun 16 21:46:58 2020] pci 0000:00:00.2: AMD-Vi: Extended features (0xf77ef22294ada):
$ dmesg -T --level=warn | grep "PPR"
[Tue Jun 16 21:46:58 2020] PPR NX GT IA GA PC GA_vAPIC
The problem is, that commit 3928aa3f57 ("iommu/amd: Detect and enable
guest vAPIC support") introduced a newline, causing `pr_cont()`, used to
print the features, to default back to the default log level.
/**
* pr_cont - Continues a previous log message in the same line.
* @fmt: format string
* @...: arguments for the format string
*
* This macro expands to a printk with KERN_CONT loglevel. It should only be
* used when continuing a log message with no newline ('\n') enclosed. Otherwise
* it defaults back to KERN_DEFAULT loglevel.
*/
#define pr_cont(fmt, ...) \
printk(KERN_CONT fmt, ##__VA_ARGS__)
So, remove the line break, so only one line is logged.
Fixes: 3928aa3f57 ("iommu/amd: Detect and enable guest vAPIC support")
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Cc: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Cc: iommu@lists.linux-foundation.org
Link: https://lore.kernel.org/r/20200616220420.19466-1-pmenzel@molgen.mpg.de
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Some PCIe devices do not expect a PASID value in PRI Page Responses.
If the "PRG Response PASID Required" bit in the PRI capability is zero,
then the OS should not set the PASID field. Similarly on Arm SMMU,
responses to stall events do not have a PASID.
Currently iommu_page_response() systematically checks that the PASID in
the page response corresponds to the one in the page request. This can't
work with virtualization because a page response coming from a guest OS
won't have a PASID if the passed-through device does not require one.
Add a flag to page requests that declares whether the corresponding
response needs to have a PASID. When this flag isn't set, allow page
responses without PASID.
Reported-by: Shameerali Kolothum Thodi <shameerali.kolothum.thodi@huawei.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Link: https://lore.kernel.org/r/20200616144712.748818-1-jean-philippe@linaro.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Use kzfree() instead of opencoded memset with 0 followed by kfree().
Null check is not required since kzfree() checks for NULL internally.
Signed-off-by: Denis Efremov <efremov@linux.com>
Link: https://lore.kernel.org/r/20200604123709.96561-1-efremov@linux.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Unlike the other instances which represent a complete loss of
consistency within the rcache mechanism itself, or a fundamental
and obvious misconfiguration by an IOMMU driver, the BUG_ON() in
iova_magazine_free_pfns() can be provoked at more or less any time
in a "spooky action-at-a-distance" manner by any old device driver
passing nonsense to dma_unmap_*() which then propagates through to
queue_iova().
Not only is this well outside the IOVA layer's control, it's also
nowhere near fatal enough to justify panicking anyway - all that
really achieves is to make debugging the offending driver more
difficult. Let's simply WARN and otherwise ignore bogus PFNs.
Reported-by: Prakash Gupta <guptap@codeaurora.org>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Prakash Gupta <guptap@codeaurora.org>
Link: https://lore.kernel.org/r/acbd2d092b42738a03a21b417ce64e27f8c91c86.1591103298.git.robin.murphy@arm.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The iommu_domain_identity_map() helper takes start/end PFN as arguments.
Fix a misuse case where the start and end addresses are passed.
Fixes: e70b081c6f ("iommu/vt-d: Remove IOVA handling code from the non-dma_ops path")
Reported-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Cc: Tom Murphy <murphyt7@tcd.ie>
Link: https://lore.kernel.org/r/20200622231345.29722-7-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The Scalable-mode Page-walk Coherency (SMPWC) field in the VT-d extended
capability register indicates the hardware coherency behavior on paging
structures accessed through the pasid table entry. This is ignored in
current code and using ECAP.C instead which is only valid in legacy mode.
Fix this so that paging structure updates could be manually flushed from
the cache line if hardware page walking is not snooped.
Fixes: 765b6a98c1 ("iommu/vt-d: Enumerate the scalable mode capability")
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Kevin Tian <kevin.tian@intel.com>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Link: https://lore.kernel.org/r/20200622231345.29722-6-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
PCI ACS is disabled if Intel IOMMU is off by default or intel_iommu=off
is used in command line. Unfortunately, Intel IOMMU will be forced on if
there're devices sitting on an external facing PCI port that is marked
as untrusted (for example, thunderbolt peripherals). That means, PCI ACS
is disabled while Intel IOMMU is forced on to isolate those devices. As
the result, the devices of an MFD will be grouped by a single group even
the ACS is supported on device.
[ 0.691263] pci 0000:00:07.1: Adding to iommu group 3
[ 0.691277] pci 0000:00:07.2: Adding to iommu group 3
[ 0.691292] pci 0000:00:07.3: Adding to iommu group 3
Fix it by requesting PCI ACS when Intel IOMMU is detected with platform
opt in hint.
Fixes: 89a6079df7 ("iommu/vt-d: Force IOMMU on for platform opt in hint")
Co-developed-by: Lalithambika Krishnakumar <lalithambika.krishnakumar@intel.com>
Signed-off-by: Lalithambika Krishnakumar <lalithambika.krishnakumar@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Link: https://lore.kernel.org/r/20200622231345.29722-5-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Currently, an external malicious PCI device can masquerade the VID:PID
of faulty gfx devices, and thus apply iommu quirks to effectively
disable the IOMMU restrictions for itself.
Thus we need to ensure that the device we are applying quirks to, is
indeed an internal trusted device.
Signed-off-by: Rajat Jain <rajatja@google.com>
Reviewed-by: Ashok Raj <ashok.raj@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20200622231345.29722-4-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
When using first-level translation for IOVA, currently the U/S bit in the
page table is cleared which implies DMA requests with user privilege are
blocked. As the result, following error messages might be observed when
passing through a device to user level:
DMAR: DRHD: handling fault status reg 3
DMAR: [DMA Read] Request device [41:00.0] PASID 1 fault addr 7ecdcd000
[fault reason 129] SM: U/S set 0 for first-level translation
with user privilege
This fixes it by setting U/S bit in the first level page table and makes
IOVA over first level compatible with previous second-level translation.
Fixes: b802d070a5 ("iommu/vt-d: Use iova over first level")
Reported-by: Xin Zeng <xin.zeng@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20200622231345.29722-3-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Current Intel SVM is designed by setting the pgd_t of the processor page
table to FLPTR field of the PASID entry. The first level translation only
supports 4 and 5 level paging structures, hence it's infeasible for the
IOMMU to share a processor's page table when it's running in 32-bit mode.
Let's disable 32bit support for now and claim support only when all the
missing pieces are ready in the future.
Fixes: 1c4f88b7f1 ("iommu/vt-d: Shared virtual address in scalable mode")
Suggested-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20200622231345.29722-2-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
- fix build rules in binderfs sample
- fix build errors when Kbuild recurses to the top Makefile
- covert '---help---' in Kconfig to 'help'
-----BEGIN PGP SIGNATURE-----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=1NIT
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- fix build rules in binderfs sample
- fix build errors when Kbuild recurses to the top Makefile
- covert '---help---' in Kconfig to 'help'
* tag 'kbuild-v5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
treewide: replace '---help---' in Kconfig files with 'help'
kbuild: fix broken builds because of GZIP,BZIP2,LZOP variables
samples: binderfs: really compile this sample and fix build issues
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
- Move the Intel and AMD IOMMU drivers into their own
subdirectory. Both drivers consist of several files by now and
giving them their own directory unclutters the IOMMU top-level
directory a bit.
-----BEGIN PGP SIGNATURE-----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=gX8z
-----END PGP SIGNATURE-----
Merge tag 'iommu-drivers-move-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu driver directory structure cleanup from Joerg Roedel:
"Move the Intel and AMD IOMMU drivers into their own subdirectory.
Both drivers consist of several files by now and giving them their own
directory unclutters the IOMMU top-level directory a bit"
* tag 'iommu-drivers-move-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/vt-d: Move Intel IOMMU driver into subdirectory
iommu/amd: Move AMD IOMMU driver into subdirectory
Move all files related to the Intel IOMMU driver into its own
subdirectory.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20200609130303.26974-3-joro@8bytes.org
Move all files related to the AMD IOMMU driver into its own
subdirectory.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Reviewed-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Link: https://lore.kernel.org/r/20200609130303.26974-2-joro@8bytes.org
- Add support for multi-function devices in pci code.
- Enable PF-VF linking for architectures using the
pdev->no_vf_scan flag (currently just s390).
- Add reipl from NVMe support.
- Get rid of critical section cleanup in entry.S.
- Refactor PNSO CHSC (perform network subchannel operation) in cio
and qeth.
- QDIO interrupts and error handling fixes and improvements, more
refactoring changes.
- Align ioremap() with generic code.
- Accept requests without the prefetch bit set in vfio-ccw.
- Enable path handling via two new regions in vfio-ccw.
- Other small fixes and improvements all over the code.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE3QHqV+H2a8xAv27vjYWKoQLXFBgFAl7eVGcACgkQjYWKoQLX
FBhweQgAkicvx31x230rdfG+jQkQkl0UqF99vvWrJHEll77SqadfjzKAGIjUB+K0
EoeHVD5Wcj7BogDGcyHeQ0bZpu4WzE+y1nmnrsvu7TEEvcBmkJH0rF2jF+y0sb/O
3qvwFkX/CB5OqaMzKC/AEeRpcCKR+ZUXkWu1irbYth7CBXaycD9EAPc4cj8CfYGZ
r5njUdYOVk77TaO4aV+t5pCYc5TCRJaWXSsWaAv/nuLcIqsFBYOy2q+L47zITGXp
utZVanIDjzx+ikpaKicOIfC3hJsRuNX9MnlZKsQFwpVEZAUZmIUm29XdhGJTWSxU
RV7m1ORINbFP1nGAqWqkOvGo/LC0ZA==
=VhXR
-----END PGP SIGNATURE-----
Merge tag 's390-5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Vasily Gorbik:
- Add support for multi-function devices in pci code.
- Enable PF-VF linking for architectures using the pdev->no_vf_scan
flag (currently just s390).
- Add reipl from NVMe support.
- Get rid of critical section cleanup in entry.S.
- Refactor PNSO CHSC (perform network subchannel operation) in cio and
qeth.
- QDIO interrupts and error handling fixes and improvements, more
refactoring changes.
- Align ioremap() with generic code.
- Accept requests without the prefetch bit set in vfio-ccw.
- Enable path handling via two new regions in vfio-ccw.
- Other small fixes and improvements all over the code.
* tag 's390-5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (52 commits)
vfio-ccw: make vfio_ccw_regops variables declarations static
vfio-ccw: Add trace for CRW event
vfio-ccw: Wire up the CRW irq and CRW region
vfio-ccw: Introduce a new CRW region
vfio-ccw: Refactor IRQ handlers
vfio-ccw: Introduce a new schib region
vfio-ccw: Refactor the unregister of the async regions
vfio-ccw: Register a chp_event callback for vfio-ccw
vfio-ccw: Introduce new helper functions to free/destroy regions
vfio-ccw: document possible errors
vfio-ccw: Enable transparent CCW IPL from DASD
s390/pci: Log new handle in clp_disable_fh()
s390/cio, s390/qeth: cleanup PNSO CHSC
s390/qdio: remove q->first_to_kick
s390/qdio: fix up qdio_start_irq() kerneldoc
s390: remove critical section cleanup from entry.S
s390: add machine check SIGP
s390/pci: ioremap() align with generic code
s390/ap: introduce new ap function ap_get_qdev()
Documentation/s390: Update / remove developerWorks web links
...
Including:
- A big part of this is a change in how devices get connected to
IOMMUs in the core code. It contains the change from the old
add_device()/remove_device() to the new
probe_device()/release_device() call-backs. As a result
functionality that was previously in the IOMMU drivers has
been moved to the IOMMU core code, including IOMMU group
allocation for each device.
The reason for this change was to get more robust allocation
of default domains for the iommu groups.
A couple of fixes were necessary after this was merged into
the IOMMU tree, but there are no known bugs left. The last fix
is applied on-top of the merge commit for the topic branches.
- Removal of the driver private domain handling in the Intel
VT-d driver. This was fragile code and I am glad it is gone
now.
- More Intel VT-d updates from Lu Baolu:
- Nested Shared Virtual Addressing (SVA) support to the
Intel VT-d driver
- Replacement of the Intel SVM interfaces to the common
IOMMU SVA API
- SVA Page Request draining support
- ARM-SMMU Updates from Will:
- Avoid mapping reserved MMIO space on SMMUv3, so that
it can be claimed by the PMU driver
- Use xarray to manage ASIDs on SMMUv3
- Reword confusing shutdown message
- DT compatible string updates
- Allow implementations to override the default domain
type
- A new IOMMU driver for the Allwinner Sun50i platform
- Support for ATS gets disabled for untrusted devices (like
Thunderbolt devices). This includes a PCI patch, acked by
Bjorn.
- Some cleanups to the AMD IOMMU driver to make more use of
IOMMU core features.
- Unification of some printk formats in the Intel and AMD IOMMU
drivers and in the IOVA code.
- Updates for DT bindings
- A number of smaller fixes and cleanups.
-----BEGIN PGP SIGNATURE-----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=a4z4
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu updates from Joerg Roedel:
"A big part of this is a change in how devices get connected to IOMMUs
in the core code. It contains the change from the old add_device() /
remove_device() to the new probe_device() / release_device()
call-backs.
As a result functionality that was previously in the IOMMU drivers has
been moved to the IOMMU core code, including IOMMU group allocation
for each device. The reason for this change was to get more robust
allocation of default domains for the iommu groups.
A couple of fixes were necessary after this was merged into the IOMMU
tree, but there are no known bugs left. The last fix is applied on-top
of the merge commit for the topic branches.
Other than that change, we have:
- Removal of the driver private domain handling in the Intel VT-d
driver. This was fragile code and I am glad it is gone now.
- More Intel VT-d updates from Lu Baolu:
- Nested Shared Virtual Addressing (SVA) support to the Intel VT-d
driver
- Replacement of the Intel SVM interfaces to the common IOMMU SVA
API
- SVA Page Request draining support
- ARM-SMMU Updates from Will:
- Avoid mapping reserved MMIO space on SMMUv3, so that it can be
claimed by the PMU driver
- Use xarray to manage ASIDs on SMMUv3
- Reword confusing shutdown message
- DT compatible string updates
- Allow implementations to override the default domain type
- A new IOMMU driver for the Allwinner Sun50i platform
- Support for ATS gets disabled for untrusted devices (like
Thunderbolt devices). This includes a PCI patch, acked by Bjorn.
- Some cleanups to the AMD IOMMU driver to make more use of IOMMU
core features.
- Unification of some printk formats in the Intel and AMD IOMMU
drivers and in the IOVA code.
- Updates for DT bindings
- A number of smaller fixes and cleanups.
* tag 'iommu-updates-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (109 commits)
iommu: Check for deferred attach in iommu_group_do_dma_attach()
iommu/amd: Remove redundant devid checks
iommu/amd: Store dev_data as device iommu private data
iommu/amd: Merge private header files
iommu/amd: Remove PD_DMA_OPS_MASK
iommu/amd: Consolidate domain allocation/freeing
iommu/amd: Free page-table in protection_domain_free()
iommu/amd: Allocate page-table in protection_domain_init()
iommu/amd: Let free_pagetable() not rely on domain->pt_root
iommu/amd: Unexport get_dev_data()
iommu/vt-d: Fix compile warning
iommu/vt-d: Remove real DMA lookup in find_domain
iommu/vt-d: Allocate domain info for real DMA sub-devices
iommu/vt-d: Only clear real DMA device's context entries
iommu: Remove iommu_sva_ops::mm_exit()
uacce: Remove mm_exit() op
iommu/sun50i: Constify sun50i_iommu_ops
iommu/hyper-v: Constify hyperv_ir_domain_ops
iommu/vt-d: Use pci_ats_supported()
iommu/arm-smmu-v3: Use pci_ats_supported()
...
- enhance the dma pool to allow atomic allocation on x86 with AMD SEV
(David Rientjes)
- two small cleanups (Jason Yan and Peter Collingbourne)
-----BEGIN PGP SIGNATURE-----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=GT3J
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-5.8' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- enhance the dma pool to allow atomic allocation on x86 with AMD SEV
(David Rientjes)
- two small cleanups (Jason Yan and Peter Collingbourne)
* tag 'dma-mapping-5.8' of git://git.infradead.org/users/hch/dma-mapping:
dma-contiguous: fix comment for dma_release_from_contiguous
dma-pool: scale the default DMA coherent pool size with memory capacity
x86/mm: unencrypted non-blocking DMA allocations use coherent pools
dma-pool: add pool sizes to debugfs
dma-direct: atomic allocations must come from atomic coherent pools
dma-pool: dynamically expanding atomic pools
dma-pool: add additional coherent pools to map to gfp mask
dma-remap: separate DMA atomic pools from direct remap code
dma-debug: make __dma_entry_alloc_check_leak() static
The iommu_group_do_dma_attach() must not attach devices which have
deferred_attach set. Otherwise devices could cause IOMMU faults when
re-initialized in a kdump kernel.
Fixes: deac0b3bed ("iommu: Split off default domain allocation from group assignment")
Reported-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Tested-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Link: https://lore.kernel.org/r/20200604091944.26402-1-joro@8bytes.org
Checking the return value of get_device_id() in a code-path which has
already done check_device() is not needed, as check_device() does the
same check and bails out if it fails.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Reviewed-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Link: https://lore.kernel.org/r/20200527115313.7426-11-joro@8bytes.org
Do not use dev->archdata.iommu anymore and switch to using the private
per-device pointer provided by the IOMMU core code.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Reviewed-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Link: https://lore.kernel.org/r/20200527115313.7426-10-joro@8bytes.org
This is covered by IOMMU_DOMAIN_DMA from the IOMMU core code already,
so remove it.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Reviewed-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Link: https://lore.kernel.org/r/20200527115313.7426-8-joro@8bytes.org
Align release of the page-table with the place where it is allocated.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Reviewed-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Link: https://lore.kernel.org/r/20200527115313.7426-6-joro@8bytes.org
Use 'struct domain_pgtable' instead to free_pagetable(). This solves
the problem that amd_iommu_domain_direct_map() needs to restore
domain->pt_root after the device table has been updated just to make
free_pagetable release the domain page-table.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Reviewed-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Link: https://lore.kernel.org/r/20200527115313.7426-4-joro@8bytes.org
This function is internal to the AMD IOMMU driver and only exported
because the amd_iommu_v2 modules calls it. But the reason it is called
from there could better be handled by amd_iommu_is_attach_deferred().
So unexport get_dev_data() and use amd_iommu_is_attach_deferred()
instead.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Reviewed-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Link: https://lore.kernel.org/r/20200527115313.7426-3-joro@8bytes.org
kobject_init_and_add() takes reference even when it fails.
Thus, when kobject_init_and_add() returns an error,
kobject_put() must be called to properly clean up the kobject.
Fixes: d72e31c937 ("iommu: IOMMU Groups")
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Link: https://lore.kernel.org/r/20200527210020.6522-1-wu000273@umn.edu
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Make intel_svm_unbind_mm() a static function.
Fixes: 064a57d7dd ("iommu/vt-d: Replace intel SVM APIs with generic SVA APIs")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/1590689031-79318-1-git-send-email-jacob.jun.pan@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
By removing the real DMA indirection in find_domain(), we can allow
sub-devices of a real DMA device to have their own valid
device_domain_info. The dmar lookup and context entry removal paths have
been fixed to account for sub-devices.
Fixes: 2b0140c696 ("iommu/vt-d: Use pci_real_dma_dev() for mapping")
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20200527165617.297470-4-jonathan.derrick@intel.com
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=207575
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Sub-devices of a real DMA device might exist on a separate segment than
the real DMA device and its IOMMU. These devices should still have a
valid device_domain_info, but the current dma alias model won't
allocate info for the subdevice.
This patch adds a segment member to struct device_domain_info and uses
the sub-device's BDF so that these sub-devices won't alias to other
devices.
Fixes: 2b0140c696 ("iommu/vt-d: Use pci_real_dma_dev() for mapping")
Cc: stable@vger.kernel.org # v5.6+
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20200527165617.297470-3-jonathan.derrick@intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Domain context mapping can encounter issues with sub-devices of a real
DMA device. A sub-device cannot have a valid context entry due to it
potentially aliasing another device's 16-bit ID. It's expected that
sub-devices of the real DMA device uses the real DMA device's requester
when context mapping.
This is an issue when a sub-device is removed where the context entry is
cleared for all aliases. Other sub-devices are still valid, resulting in
those sub-devices being stranded without valid context entries.
The correct approach is to use the real DMA device when programming the
context entries. The insertion path is correct because device_to_iommu()
will return the bus and devfn of the real DMA device. The removal path
needs to only operate on the real DMA device, otherwise the entire
context entry would be cleared for all sub-devices of the real DMA
device.
This patch also adds a helper to determine if a struct device is a
sub-device of a real DMA device.
Fixes: 2b0140c696 ("iommu/vt-d: Use pci_real_dma_dev() for mapping")
Cc: stable@vger.kernel.org # v5.6+
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20200527165617.297470-2-jonathan.derrick@intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
After binding a device to an mm, device drivers currently need to
register a mm_exit handler. This function is called when the mm exits,
to gracefully stop DMA targeting the address space and flush page faults
to the IOMMU.
This is deemed too complex for the MMU release() notifier, which may be
triggered by any mmput() invocation, from about 120 callsites [1]. The
upcoming SVA module has an example of such complexity: the I/O Page
Fault handler would need to call mmput_async() instead of mmput() after
handling an IOPF, to avoid triggering the release() notifier which would
in turn drain the IOPF queue and lock up.
Another concern is the DMA stop function taking too long, up to several
minutes [2]. For some mmput() callers this may disturb other users. For
example, if the OOM killer picks the mm bound to a device as the victim
and that mm's memory is locked, if the release() takes too long, it
might choose additional innocent victims to kill.
To simplify the MMU release notifier, don't forward the notification to
device drivers. Since they don't stop DMA on mm exit anymore, the PASID
lifetime is extended:
(1) The device driver calls bind(). A PASID is allocated.
Here any DMA fault is handled by mm, and on error we don't print
anything to dmesg. Userspace can easily trigger errors by issuing DMA
on unmapped buffers.
(2) exit_mmap(), for example the process took a SIGKILL. This step
doesn't happen during normal operations. Remove the pgd from the
PASID table, since the page tables are about to be freed. Invalidate
the IOTLBs.
Here the device may still perform DMA on the address space. Incoming
transactions are aborted but faults aren't printed out. ATS
Translation Requests return Successful Translation Completions with
R=W=0. PRI Page Requests return with Invalid Request.
(3) The device driver stops DMA, possibly following release of a fd, and
calls unbind(). PASID table is cleared, IOTLB invalidated if
necessary. The page fault queues are drained, and the PASID is
freed.
If DMA for that PASID is still running here, something went seriously
wrong and errors should be reported.
For now remove iommu_sva_ops entirely. We might need to re-introduce
them at some point, for example to notify device drivers of unhandled
IOPF.
[1] https://lore.kernel.org/linux-iommu/20200306174239.GM31668@ziepe.ca/
[2] https://lore.kernel.org/linux-iommu/4d68da96-0ad5-b412-5987-2f7a6aa796c3@amd.com/
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20200423125329.782066-3-jean-philippe@linaro.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The struct sun50i_iommu_ops is not modified and can be made const to
allow the compiler to put it in read-only memory.
Before:
text data bss dec hex filename
14358 2501 64 16923 421b drivers/iommu/sun50i-iommu.o
After:
text data bss dec hex filename
14726 2117 64 16907 420b drivers/iommu/sun50i-iommu.o
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20200525214958.30015-3-rikard.falkeborn@gmail.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The struct hyperv_ir_domain_ops is not modified and can be made const to
allow the compiler to put it in read-only memory.
Before:
text data bss dec hex filename
2916 1180 1120 5216 1460 drivers/iommu/hyperv-iommu.o
After:
text data bss dec hex filename
3044 1052 1120 5216 1460 drivers/iommu/hyperv-iommu.o
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Acked-by: Wei Liu <wei.liu@kernel.org>
Link: https://lore.kernel.org/r/20200525214958.30015-2-rikard.falkeborn@gmail.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The pci_ats_supported() helper checks if a device supports ATS and is
allowed to use it. By checking the ATS capability it also integrates the
pci_ats_disabled() check from pci_ats_init(). Simplify the vt-d checks.
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20200520152201.3309416-5-jean-philippe@linaro.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The new pci_ats_supported() function checks if a device supports ATS and
is allowed to use it.
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20200520152201.3309416-4-jean-philippe@linaro.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The pci_ats_supported() function checks if a device supports ATS and is
allowed to use it. In addition to checking that the device has an ATS
capability and that the global pci=noats is not set
(pci_ats_disabled()), it also checks if a device is untrusted.
A device is untrusted if it is plugged into an external-facing port such
as Thunderbolt and could be spoofing an existing device to exploit
weaknesses in the IOMMU configuration. By calling pci_ats_supported() we
keep DTE[I]=0 for untrusted devices and abort transactions with
Pretranslated Addresses.
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
Link: https://lore.kernel.org/r/20200520152201.3309416-3-jean-philippe@linaro.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The iommu_alloc_default_domain() function takes a reference to an IOMMU
group without releasing it. This causes the group to never be released,
with undefined side effects.
The function has only one call-site, which takes a group reference on
its own, so to fix this leak, do not take another reference in
iommu_alloc_default_domain() and pass the group as a function parameter
instead.
Fixes: 6e1aa20491 ("iommu: Move default domain allocation to iommu_probe_device()")
Reported-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Tested-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Cc: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Link: https://lore.kernel.org/r/20200525130122.380-1-joro@8bytes.org
Reference: https://lore.kernel.org/lkml/20200522130145.30067-1-saiprakash.ranjan@codeaurora.org/
Pointers should be casted to unsigned long to avoid "cast from pointer
to integer of different size" warnings.
drivers/iommu/intel-pasid.c:818:6: warning:
cast from pointer to integer of different size [-Wpointer-to-int-cast]
drivers/iommu/intel-pasid.c:821:9: warning:
cast from pointer to integer of different size [-Wpointer-to-int-cast]
drivers/iommu/intel-pasid.c:824:23: warning:
cast from pointer to integer of different size [-Wpointer-to-int-cast]
drivers/iommu/intel-svm.c:343:45: warning:
cast to pointer from integer of different size [-Wint-to-pointer-cast]
Fixes: b0d1f8741b ("iommu/vt-d: Add nested translation helper function")
Fixes: 56722a4398 ("iommu/vt-d: Add bind guest PASID support")
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20200519013423.11971-1-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The .probe_finalize() call-back of some IOMMU drivers calls into
arm_iommu_attach_device(). This function will call back into the
IOMMU core code, where it tries to take group->mutex again, resulting
in a deadlock.
As there is no reason why .probe_finalize() needs to be called under
that mutex, move it after the lock has been released to fix the
deadlock.
Fixes: deac0b3bed ("iommu: Split off default domain allocation from group assignment")
Reported-by: Yong Wu <yong.wu@mediatek.com>
Tested-by: Yong Wu <yong.wu@mediatek.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Cc: Yong Wu <yong.wu@mediatek.com>
Link: https://lore.kernel.org/r/20200519132824.15163-1-joro@8bytes.org
In preparation for sharing some ASIDs with the CPU, use a global xarray to
store ASIDs and their context. ASID#0 is now reserved, and the ASID
space is global.
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Link: https://lore.kernel.org/r/20200519175502.2504091-9-jean-philippe@linaro.org
Signed-off-by: Will Deacon <will@kernel.org>
The IOMMU core code has support for deferring the attachment of a domain
to a device. This is needed in kdump kernels where the new domain must
not be attached to a device before the device driver takes it over.
When the AMD IOMMU driver got converted to use the dma-iommu
implementation, the deferred attaching got lost. The code in
dma-iommu.c has support for deferred attaching, but it calls into
iommu_attach_device() to actually do it. But iommu_attach_device()
will check if the device should be deferred in it code-path and do
nothing, breaking deferred attachment.
Move the is_deferred_attach() check out of the attach_device path and
into iommu_group_add_device() to make deferred attaching work from the
dma-iommu code.
Fixes: 795bbbb9b6 ("iommu/dma-iommu: Handle deferred devices")
Reported-by: Jerry Snitselaar <jsnitsel@redhat.com>
Suggested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Tested-by: Jerry Snitselaar <jsnitsel@redhat.com>
Cc: Jerry Snitselaar <jsnitsel@redhat.com>
Cc: Tom Murphy <murphyt7@tcd.ie>
Cc: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/20200519130340.14564-1-joro@8bytes.org
On some SoCs like MSM8939 with A405 adreno, there is a gfx_tbu clock
needs to be on while doing TLB invalidate. Otherwise, TLBSYNC status
will not be correctly reflected, causing the system to go into a bad
state. Add it as an optional clock, so that platforms that have this
clock can pass it over DT.
While adding the third clock, let's switch to bulk clk API to simplify
the enable/disable calls. clk_bulk_get() cannot used because the
existing two clocks are required while the new one is optional.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200518141656.26284-1-shawn.guo@linaro.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
In case of error, the function devm_platform_ioremap_resource() returns
ERR_PTR() not NULL. The NULL test in the return value check must be
replaced with IS_ERR().
Fixes: 4100b8c229 ("iommu: Add Allwinner H6 IOMMU driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20200519091857.134170-1-weiyongjun1@huawei.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Some SMMUv3 implementation embed the Perf Monitor Group Registers (PMCG)
inside the first 64kB region of the SMMU. Since PMCG are managed by a
separate driver, this layout causes resource reservation conflicts
during boot.
To avoid this conflict, don't reserve the MMIO regions that are
implementation defined. Although devm_ioremap_resource() still works on
full pages under the hood, this way we benefit from resource conflict
checks.
Fixes: 7d839b4b9e ("perf/smmuv3: Add arm64 smmuv3 pmu driver")
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/20200513110255.597203-1-jean-philippe@linaro.org
Signed-off-by: Will Deacon <will@kernel.org>
The modem remote processor has two access paths to DDR. One path is
directly connected to DDR and another path goes through an SMMU. The
SMMU path is configured to be a direct mapping because it's used by
various peripherals in the modem subsystem. Typically this direct
mapping is configured statically at EL2 by QHEE (Qualcomm's Hypervisor
Execution Environment) before the kernel is entered.
In certain firmware configuration, especially when the kernel is already
in full control of the SMMU, defer programming the modem SIDs to the
kernel. Let's add compatibles here so that we can have the kernel
program the SIDs for the modem in these cases.
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20200511175532.25874-1-sibis@codeaurora.org
Signed-off-by: Will Deacon <will@kernel.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/iommu/arm-smmu-v3.c:2989:26:
warning: variable ‘smmu’ set but not used [-Wunused-but-set-variable]
struct arm_smmu_device *smmu;
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Chen Zhou <chenzhou10@huawei.com>
Link: https://lore.kernel.org/r/20200508014955.87630-1-chenzhou10@huawei.com
Signed-off-by: Will Deacon <will@kernel.org>
The MediaTek V1 IOMMU is arm32 whose default domain type is
IOMMU_DOMAIN_UNMANAGED. Add this to satisfy the bus_iommu_probe to
enter "probe_finalize".
The iommu framework will create a iommu domain for each a device.
But all the devices share a iommu domain here, thus we skip all the
other domains in the "attach_device" except the domain we create
internally with arm_iommu_create_mapping.
Also a minor change: in the attach_device, "data" always is not null.
Remove "if (!data) return".
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Link: https://lore.kernel.org/r/1589530123-30240-1-git-send-email-yong.wu@mediatek.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The fwnode pointer must be passed to the iommu core, so that the core
can map the IOMMU towards device requests properly. Without this, some
IOMMU clients like OMAP remoteproc will fail the iommu configuration
multiple times with -EPROBE_DEFER, which will eventually be ignored with
a kernel warning banner.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Link: https://lore.kernel.org/r/20200424145828.3159-1-t-kristo@ti.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
There's no need for the non-dma_ops path to keep track of IOVAs. The
whole point of the non-dma_ops path is that it allows the IOVAs to be
handled separately. The IOVA handling code removed in this patch is
pointless.
Signed-off-by: Tom Murphy <murphyt7@tcd.ie>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20200516062101.29541-19-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The info and info->pasid_support have already been checked in previous
intel_iommu_enable_pasid() call. No need to check again.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20200516062101.29541-18-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
IOTLB flush already included in the PASID tear down and the page request
drain process. There is no need to flush again.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Link: https://lore.kernel.org/r/20200516062101.29541-17-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
When a PASID is stopped or terminated, there can be pending PRQs
(requests that haven't received responses) in remapping hardware.
This adds the interface to drain page requests and call it when a
PASID is terminated.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Liu Yi L <yi.l.liu@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20200516062101.29541-16-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
When a PASID is used for SVA by the device, it's possible that the PASID
entry is cleared before the device flushes all ongoing DMA requests. The
IOMMU should tolerate and ignore the non-recoverable faults caused by the
untranslated requests from this device.
For example, when an exception happens, the process terminates before the
device driver stops DMA and call IOMMU driver to unbind PASID. The flow
of process exist is as follows:
do_exit() {
exit_mm() {
mm_put();
exit_mmap() {
intel_invalidate_range() //mmu notifier
tlb_finish_mmu()
mmu_notifier_release(mm) {
intel_iommu_release() {
[2] intel_iommu_teardown_pasid();
intel_iommu_flush_tlbs();
}
}
unmap_vmas();
free_pgtables();
};
}
exit_files(tsk) {
close_files() {
dsa_close();
[1] dsa_stop_dma();
intel_svm_unbind_pasid();
}
}
}
Care must be taken on VT-d to avoid unrecoverable faults between the time
window of [1] and [2]. [Process exist flow was contributed by Jacob Pan.]
Intel VT-d provides such function through the FPD bit of the PASID entry.
This sets FPD bit when PASID entry is changing from present to nonpresent
in the mm notifier and will clear it when the pasid is unbound.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Link: https://lore.kernel.org/r/20200516062101.29541-15-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Current qi_submit_sync() only supports single invalidation descriptor
per submission and appends wait descriptor after each submission to
poll the hardware completion. This extends the qi_submit_sync() helper
to support multiple descriptors, and add an option so that the caller
could specify the Page-request Drain (PD) bit in the wait descriptor.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Link: https://lore.kernel.org/r/20200516062101.29541-13-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This patch is an initial step to replace Intel SVM code with the
following IOMMU SVA ops:
intel_svm_bind_mm() => iommu_sva_bind_device()
intel_svm_unbind_mm() => iommu_sva_unbind_device()
intel_svm_is_pasid_valid() => iommu_sva_get_pasid()
The features below will continue to work but are not included in this patch
in that they are handled mostly within the IOMMU subsystem.
- IO page fault
- mmu notifier
Consolidation of the above will come after merging generic IOMMU sva
code[1]. There should not be any changes needed for SVA users such as
accelerator device drivers during this time.
[1] http://jpbrucker.net/sva/
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20200516062101.29541-12-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Query Shared Virtual Address/Memory capability is a generic feature.
SVA feature check is the required first step before calling
iommu_sva_bind_device().
VT-d checks SVA feature enabling at per IOMMU level during this step,
SVA bind device will check and enable PCI ATS, PRS, and PASID capabilities
at device level.
This patch reports Intel SVM as SVA feature such that generic code
(e.g. Uacce [1]) can use it.
[1] https://lkml.org/lkml/2020/1/15/604
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20200516062101.29541-11-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
When VT-d driver runs in the guest, PASID allocation must be
performed via virtual command interface. This patch registers a
custom IOASID allocator which takes precedence over the default
XArray based allocator. The resulting IOASID allocation will always
come from the host. This ensures that PASID namespace is system-
wide.
Virtual command registers are used in the guest only, to prevent
vmexit cost, we cache the capability and store it during initialization.
Signed-off-by: Liu, Yi L <yi.l.liu@intel.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Link: https://lore.kernel.org/r/20200516062101.29541-9-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Enabling IOMMU in a guest requires communication with the host
driver for certain aspects. Use of PASID ID to enable Shared Virtual
Addressing (SVA) requires managing PASID's in the host. VT-d 3.0 spec
provides a Virtual Command Register (VCMD) to facilitate this.
Writes to this register in the guest are trapped by vIOMMU which
proxies the call to the host driver.
This virtual command interface consists of a capability register,
a virtual command register, and a virtual response register. Refer
to section 10.4.42, 10.4.43, 10.4.44 for more information.
This patch adds the enlightened PASID allocation/free interfaces
via the virtual command interface.
Signed-off-by: Liu Yi L <yi.l.liu@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Link: https://lore.kernel.org/r/20200516062101.29541-8-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
When Shared Virtual Address (SVA) is enabled for a guest OS via
vIOMMU, we need to provide invalidation support at IOMMU API and driver
level. This patch adds Intel VT-d specific function to implement
iommu passdown invalidate API for shared virtual address.
The use case is for supporting caching structure invalidation
of assigned SVM capable devices. Emulated IOMMU exposes queue
invalidation capability and passes down all descriptors from the guest
to the physical IOMMU.
The assumption is that guest to host device ID mapping should be
resolved prior to calling IOMMU driver. Based on the device handle,
host IOMMU driver can replace certain fields before submit to the
invalidation queue.
Signed-off-by: Liu Yi L <yi.l.liu@intel.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Link: https://lore.kernel.org/r/20200516062101.29541-7-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
When Shared Virtual Memory is exposed to a guest via vIOMMU, scalable
IOTLB invalidation may be passed down from outside IOMMU subsystems.
This patch adds invalidation functions that can be used for additional
translation cache types.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Link: https://lore.kernel.org/r/20200516062101.29541-6-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
When supporting guest SVA with emulated IOMMU, the guest PASID
table is shadowed in VMM. Updates to guest vIOMMU PASID table
will result in PASID cache flush which will be passed down to
the host as bind guest PASID calls.
For the SL page tables, it will be harvested from device's
default domain (request w/o PASID), or aux domain in case of
mediated device.
.-------------. .---------------------------.
| vIOMMU | | Guest process CR3, FL only|
| | '---------------------------'
.----------------/
| PASID Entry |--- PASID cache flush -
'-------------' |
| | V
| | CR3 in GPA
'-------------'
Guest
------| Shadow |--------------------------|--------
v v v
Host
.-------------. .----------------------.
| pIOMMU | | Bind FL for GVA-GPA |
| | '----------------------'
.----------------/ |
| PASID Entry | V (Nested xlate)
'----------------\.------------------------------.
| | |SL for GPA-HPA, default domain|
| | '------------------------------'
'-------------'
Where:
- FL = First level/stage one page tables
- SL = Second level/stage two page tables
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Liu Yi L <yi.l.liu@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20200516062101.29541-5-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Nested translation mode is supported in VT-d 3.0 Spec.CH 3.8.
With PASID granular translation type set to 0x11b, translation
result from the first level(FL) also subject to a second level(SL)
page table translation. This mode is used for SVA virtualization,
where FL performs guest virtual to guest physical translation and
SL performs guest physical to host physical translation.
This patch adds a helper function for setting up nested translation
where second level comes from a domain and first level comes from
a guest PGD.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Liu Yi L <yi.l.liu@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Link: https://lore.kernel.org/r/20200516062101.29541-4-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
An Intel iommu domain uses 5-level page table by default. If the iommu
that the domain tries to attach supports less page levels, the top level
page tables should be skipped. Add a helper to do this so that it could
be used in other places.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Link: https://lore.kernel.org/r/20200516062101.29541-3-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Move domain helper to header to be used by SVA code.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Link: https://lore.kernel.org/r/20200516062101.29541-2-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Most of the devices in OMAP family of SoCs are not using IOMMU. The
patch for converting the OMAP IOMMU to use generic IOMMU bus probe
functionality failed to add a check for this, so add it here.
Fixes: c822b37cac ("iommu/omap: Remove orphan_dev tracking")
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Link: https://lore.kernel.org/r/20200518111057.23140-1-t-kristo@ti.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
After moving iommu_group setup to iommu core code [1][2] and removing
private domain support in vt-d [3], there are no users for functions such
as iommu_request_dm_for_dev(), iommu_request_dma_domain_for_dev() and
request_default_domain_for_dev(). So, remove these functions.
[1] commit dce8d6964e ("iommu/amd: Convert to probe/release_device()
call-backs")
[2] commit e5d1841f18 ("iommu/vt-d: Convert to probe/release_device()
call-backs")
[3] commit 327d5b2fee ("iommu/vt-d: Allow 32bit devices to uses DMA
domain")
Signed-off-by: Sai Praneeth Prakhya <sai.praneeth.prakhya@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20200513224721.20504-1-sai.praneeth.prakhya@intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
A few compile warnings show up when building this driver:
CC drivers/iommu/sun50i-iommu.o
drivers/iommu/sun50i-iommu.c: In function ‘sun50i_dte_get_page_table’:
drivers/iommu/sun50i-iommu.c:486:16: warning: unused variable ‘flags’ [-Wunused-variable]
486 | unsigned long flags;
| ^~~~~
drivers/iommu/sun50i-iommu.c: In function ‘sun50i_iommu_unmap’:
drivers/iommu/sun50i-iommu.c:559:23: warning: unused variable ‘iommu’ [-Wunused-variable]
559 | struct sun50i_iommu *iommu = sun50i_domain->iommu;
| ^~~~~
drivers/iommu/sun50i-iommu.c: In function ‘sun50i_iommu_probe_device’:
drivers/iommu/sun50i-iommu.c:749:22: warning: unused variable ‘group’ [-Wunused-variable]
749 | struct iommu_group *group;
| ^~~~~
Remove the unused variables.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Cc: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20200514124621.25999-1-joro@8bytes.org
The Allwinner H6 has introduced an IOMMU for a few DMA controllers, mostly
video related: the display engine, the video decoders / encoders, the
camera capture controller, etc.
The design is pretty simple compared to other IOMMUs found in SoCs: there's
a single instance, controlling all the masters, with a single address
space.
It also features a performance monitoring unit that allows to retrieve
various informations (per-master and global TLB accesses, hits and misses,
access latency, etc) that isn't supported at the moment.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/d122a8670361e36fc26b4ce2674a2223d30dc4cc.1589378833.git-series.maxime@cerno.tech
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Unify format of the printed messages, i.e. replace printk(LEVEL ... )
with pr_level(...).
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20200507161804.13275-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Current Intel IOMMU driver sets the system level dma_ops. This causes
each dma API to go through the IOMMU driver even the devices are using
identity mapped domains. This sets per-device dma_ops only if a device
is using a DMA domain. Otherwise, use the default system level dma_ops
for direct dma.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Tested-by: Daniel Drake <drake@endlessm.com>
Reviewed-by: Jon Derrick <jonathan.derrick@intel.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Link: https://lore.kernel.org/r/20200506015947.28662-4-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Before commit fa954e6831 ("iommu/vt-d: Delegate the dma domain
to upper layer"), Intel IOMMU started off with all devices in the
identity domain, and took them out later if it found they couldn't
access all of memory. This required devices behind a PCI bridge to
use a DMA domain at the beginning because all PCI devices behind
the bridge use the same source-id in their transactions and the
domain couldn't be changed at run-time.
Intel IOMMU driver is now aligned with the default domain framework,
there's no need to keep this requirement anymore.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Tested-by: Daniel Drake <drake@endlessm.com>
Reviewed-by: Jon Derrick <jonathan.derrick@intel.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Link: https://lore.kernel.org/r/20200506015947.28662-3-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Currently, if a 32bit device initially uses an identity domain, Intel
IOMMU driver will convert it forcibly to a DMA one if its address
capability is not enough for the whole system memory. The motivation was
to overcome the overhead caused by possible bounced buffer.
Unfortunately, this improvement has led to many problems. For example,
some 32bit devices are required to use an identity domain, forcing them
to use DMA domain will cause the device not to work anymore. On the
other hand, the VMD sub-devices share a domain but each sub-device might
have different address capability. Forcing a VMD sub-device to use DMA
domain blindly will impact the operation of other sub-devices without
any notification. Further more, PCI aliased devices (PCI bridge and all
devices beneath it, VMD devices and various devices quirked with
pci_add_dma_alias()) must use the same domain. Forcing one device to
switch to DMA domain during runtime will cause in-fligh DMAs for other
devices to abort or target to other memory which might cause undefind
system behavior.
With the last private domain usage in iommu_need_mapping() removed, all
private domain helpers are also cleaned in this patch. Otherwise, the
compiler will complain that some functions are defined but not used.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Tested-by: Daniel Drake <drake@endlessm.com>
Reviewed-by: Jon Derrick <jonathan.derrick@intel.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Cc: Daniel Drake <drake@endlessm.com>
Cc: Derrick Jonathan <jonathan.derrick@intel.com>
Cc: Jerry Snitselaar <jsnitsel@redhat.com>
Link: https://lore.kernel.org/r/20200506015947.28662-2-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Fix the following sparse warning:
drivers/iommu/msm_iommu.c:37:1: warning: symbol 'msm_iommu_lock' was not declared.
The msm_iommu_lock has only call site within msm_iommu.c
It should be static
Fixes: 0720d1f052 ("msm: Add MSM IOMMU support")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Samuel Zou <zou_wei@huawei.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1589249839-105820-1-git-send-email-zou_wei@huawei.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
acpi_dev_hid_uid_match() expects a null pointer for UID if it doesn't
exist. The acpihid_map_entry contains a char buffer for holding the
UID. If no UID was provided in the IVRS table, this buffer will be
zeroed. If we pass in a null string, acpi_dev_hid_uid_match() will
return false because it will try and match an empty string to the ACPI
UID of the device.
Fixes: ae5e6c6439 ("iommu/amd: Switch to use acpi_dev_hid_uid_match()")
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200511103229.v2.1.I6f1b6f973ee6c8af1348611370c73a0ec0ea53f1@changeid
Signed-off-by: Joerg Roedel <jroedel@suse.de>
IVRS parsing code always tries to read 255 bytes from memory when
retrieving ACPI device path, and makes an assumption that firmware
provides a zero-terminated string. Both of those are bugs: the entry
is likely to be shorter than 255 bytes, and zero-termination is not
guaranteed.
With Acer SF314-42 firmware these issues manifest visibly in dmesg:
AMD-Vi: ivrs, add hid:AMDI0020, uid:\_SB.FUR0\xf0\xa5, rdevid:160
AMD-Vi: ivrs, add hid:AMDI0020, uid:\_SB.FUR1\xf0\xa5, rdevid:160
AMD-Vi: ivrs, add hid:AMDI0020, uid:\_SB.FUR2\xf0\xa5, rdevid:160
AMD-Vi: ivrs, add hid:AMDI0020, uid:\_SB.FUR3>\x83e\x8d\x9a\xd1...
The first three lines show how the code over-reads adjacent table
entries into the UID, and in the last line it even reads garbage data
beyond the end of the IVRS table itself.
Since each entry has the length of the UID (uidl member of ivhd_entry
struct), use that for memcpy, and manually add a zero terminator.
Avoid zero-filling hid and uid arrays up front, and instead ensure
the uid array is always zero-terminated. No change needed for the hid
array, as it was already properly zero-terminated.
Fixes: 2a0cb4e2d4 ("iommu/amd: Add new map for storing IVHD dev entry type HID")
Signed-off-by: Alexander Monakov <amonakov@ispras.ru>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: iommu@lists.linux-foundation.org
Link: https://lore.kernel.org/r/20200511102352.1831-1-amonakov@ispras.ru
Signed-off-by: Joerg Roedel <jroedel@suse.de>
gcc warns because the only reference to ipmmu_find_group
is inside of an #ifdef:
drivers/iommu/ipmmu-vmsa.c:878:28: error: 'ipmmu_find_group' defined but not used [-Werror=unused-function]
Change the #ifdef to an equivalent IS_ENABLED().
Fixes: 6580c8a784 ("iommu/renesas: Convert to probe/release_device() call-backs")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Simon Horman <horms@verge.net.au>
Link: https://lore.kernel.org/r/20200508220224.688985-1-arnd@arndb.de
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The host1x bus implemented on Tegra SoCs is primarily an abstraction to
create logical device from multiple platform devices. Since the devices
in such a setup are typically hierarchical, DMA setup still needs to be
done so that DMA masks can be properly inherited, but we don't actually
want to attach the host1x logical devices to any IOMMU. The platform
devices that make up the logical device are responsible for memory bus
transactions, so it is them that will need to be attached to the IOMMU.
Add a check to __iommu_probe_device() that aborts IOMMU setup early for
busses that don't have the IOMMU operations pointer set since they will
cause a crash otherwise.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20200511161000.3853342-1-thierry.reding@gmail.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The commit dce8d6964e ("iommu/amd: Convert to probe/release_device()
call-backs") introduced an unused variable,
drivers/iommu/amd_iommu.c: In function 'amd_iommu_uninit_device':
drivers/iommu/amd_iommu.c:422:20: warning: variable 'iommu' set but not
used [-Wunused-but-set-variable]
struct amd_iommu *iommu;
^~~~~
Signed-off-by: Qian Cai <cai@lca.pw>
Link: https://lore.kernel.org/r/20200509015645.3236-1-cai@lca.pw
Fixes: dce8d6964e ("iommu/amd: Convert to probe/release_device() call-backs")
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Elsewhere in the file, there is a list_for_each_entry with
&vdev->resv_regions as the second argument, suggesting that
&vdev->resv_regions is the list head. So exchange the
arguments on the list_add call to put the list head in the
second argument.
Fixes: 2a5a314874 ("iommu/virtio: Add probe request")
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Reviewed-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Link: https://lore.kernel.org/r/1588704467-13431-1-git-send-email-Julia.Lawall@inria.fr
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Some client devices want to directly map the IOMMU themselves instead
of using the DMA domain. Allow those devices to opt in to direct
mapping by way of a list of compatible strings.
Co-developed-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/7cf1f64167b5545b7f42275395be1f1e2ea3a6ac.1587407458.git.saiprakash.ranjan@codeaurora.org
Signed-off-by: Will Deacon <will@kernel.org>
Currently the QCOM specific smmu reset implementation is very
specific to SDM845 SoC and has a wait-for-safe logic which
may not be required for other SoCs. So move the SDM845 specific
logic to its specific reset function. Also add SC7180 SMMU
compatible for calling into QCOM specific implementation.
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/d24a0278021bc0b2732636c5728efe55e7318a8b.1587407458.git.saiprakash.ranjan@codeaurora.org
Signed-off-by: Will Deacon <will@kernel.org>
Currently on reboot/shutdown, the following messages are
displayed on the console as error messages before the
system reboots/shutdown as part of remove callback.
On SC7180:
arm-smmu 15000000.iommu: removing device with active domains!
arm-smmu 5040000.iommu: removing device with active domains!
Make this error message more informative and less scary.
Reported-by: Douglas Anderson <dianders@chromium.org>
Suggested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200423095531.9868-1-saiprakash.ranjan@codeaurora.org
[will: use dev_notice() as per Robin]
Signed-off-by: Will Deacon <will@kernel.org>
The flush of the Device Table Entries for the domain has already
happened in increase_address_space(), if necessary. Do no flush them
again in iommu_map_page().
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Tested-by: Qian Cai <cai@lca.pw>
Link: https://lore.kernel.org/r/20200504125413.16798-6-joro@8bytes.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The Device Table needs to be updated before the new page-table root
can be published in domain->pt_root. Otherwise a concurrent call to
fetch_pte might fetch a PTE which is not reachable through the Device
Table Entry.
Fixes: 92d420ec02 ("iommu/amd: Relax locking in dma_ops path")
Reported-by: Qian Cai <cai@lca.pw>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Tested-by: Qian Cai <cai@lca.pw>
Link: https://lore.kernel.org/r/20200504125413.16798-5-joro@8bytes.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The update_domain() function is expected to also inform the hardware
about domain changes. This needs a COMPLETION_WAIT command to be sent
to all IOMMUs which use the domain.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Tested-by: Qian Cai <cai@lca.pw>
Link: https://lore.kernel.org/r/20200504125413.16798-4-joro@8bytes.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
When increase_address_space() fails to allocate memory, alloc_pte()
will call it again until it succeeds. Do not loop forever while trying
to increase the address space and just return an error instead.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Tested-by: Qian Cai <cai@lca.pw>
Link: https://lore.kernel.org/r/20200504125413.16798-3-joro@8bytes.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The 'pt_root' and 'mode' struct members of 'struct protection_domain'
need to be get/set atomically, otherwise the page-table of the domain
can get corrupted.
Merge the fields into one atomic64_t struct member which can be
get/set atomically.
Fixes: 92d420ec02 ("iommu/amd: Relax locking in dma_ops path")
Reported-by: Qian Cai <cai@lca.pw>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Tested-by: Qian Cai <cai@lca.pw>
Link: https://lore.kernel.org/r/20200504125413.16798-2-joro@8bytes.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The function is now only used in IOMMU core code and shouldn't be used
outside of it anyway, so remove the export for it.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200429133712.31431-35-joro@8bytes.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Move the calls to dev_iommu_get() and try_module_get() into
__iommu_probe_device(), so that the callers don't have to do it on
their own.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200429133712.31431-34-joro@8bytes.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
All drivers are converted to use the probe/release_device()
call-backs, so the add_device/remove_device() pointers are unused and
the code using them can be removed.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200429133712.31431-33-joro@8bytes.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Convert the Exynos IOMMU driver to use the probe_device() and
release_device() call-backs of iommu_ops, so that the iommu core code
does the group and sysfs setup.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200429133712.31431-32-joro@8bytes.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
On Exynos platforms there can be more than one SYSMMU (IOMMU) for one
DMA master device. Since the IOMMU core code expects only one hardware
IOMMU, use the first SYSMMU in the list.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200429133712.31431-31-joro@8bytes.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Convert the OMAP IOMMU driver to use the probe_device() and
release_device() call-backs of iommu_ops, so that the iommu core code
does the group and sysfs setup.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Link: https://lore.kernel.org/r/20200429133712.31431-30-joro@8bytes.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Remove the tracking of device which could not be probed because
their IOMMU is not probed yet. Replace it with a call to
bus_iommu_probe() when a new IOMMU is probed.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Link: https://lore.kernel.org/r/20200429133712.31431-29-joro@8bytes.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Convert the Renesas IOMMU driver to use the probe_device() and
release_device() call-backs of iommu_ops, so that the iommu core code
does the group and sysfs setup.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Link: https://lore.kernel.org/r/20200429133712.31431-28-joro@8bytes.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Convert the Tegra IOMMU drivers to use the probe_device() and
release_device() call-backs of iommu_ops, so that the iommu core code
does the group and sysfs setup.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Link: https://lore.kernel.org/r/20200429133712.31431-27-joro@8bytes.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Convert the Rockchip IOMMU driver to use the probe_device() and
release_device() call-backs of iommu_ops, so that the iommu core code
does the group and sysfs setup.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Link: https://lore.kernel.org/r/20200429133712.31431-26-joro@8bytes.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Convert the QCOM IOMMU driver to use the probe_device() and
release_device() call-backs of iommu_ops, so that the iommu core code
does the group and sysfs setup.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Link: https://lore.kernel.org/r/20200429133712.31431-25-joro@8bytes.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Convert the Mediatek-v1 IOMMU driver to use the probe_device() and
release_device() call-backs of iommu_ops, so that the iommu core code
does the group and sysfs setup.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Link: https://lore.kernel.org/r/20200429133712.31431-24-joro@8bytes.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Convert the Mediatek IOMMU driver to use the probe_device() and
release_device() call-backs of iommu_ops, so that the iommu core code
does the group and sysfs setup.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Link: https://lore.kernel.org/r/20200429133712.31431-23-joro@8bytes.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Convert the MSM IOMMU driver to use the probe_device() and
release_device() call-backs of iommu_ops, so that the iommu core code
does the group and sysfs setup.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Link: https://lore.kernel.org/r/20200429133712.31431-22-joro@8bytes.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Convert the VirtIO IOMMU driver to use the probe_device() and
release_device() call-backs of iommu_ops, so that the iommu core code
does the group and sysfs setup.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Link: https://lore.kernel.org/r/20200429133712.31431-21-joro@8bytes.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Convert the S390 IOMMU driver to use the probe_device() and
release_device() call-backs of iommu_ops, so that the iommu core code
does the group and sysfs setup.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Link: https://lore.kernel.org/r/20200429133712.31431-20-joro@8bytes.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Convert the PAMU IOMMU driver to use the probe_device() and
release_device() call-backs of iommu_ops, so that the iommu core code
does the group and sysfs setup.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Link: https://lore.kernel.org/r/20200429133712.31431-19-joro@8bytes.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Convert the arm-smmu and arm-smmu-v3 drivers to use the probe_device() and
release_device() call-backs of iommu_ops, so that the iommu core code does the
group and sysfs setup.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Link: https://lore.kernel.org/r/20200429133712.31431-18-joro@8bytes.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Convert the Intel IOMMU driver to use the probe_device() and
release_device() call-backs of iommu_ops, so that the iommu core code
does the group and sysfs setup.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20200429133712.31431-17-joro@8bytes.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Convert the AMD IOMMU Driver to use the probe_device() and
release_device() call-backs of iommu_ops, so that the iommu core code
does the group and sysfs setup.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Link: https://lore.kernel.org/r/20200429133712.31431-16-joro@8bytes.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Make use of generic IOMMU infrastructure to gather the same information
carried in dev_data->passthrough and remove the struct member.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Link: https://lore.kernel.org/r/20200429133712.31431-15-joro@8bytes.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Add a check to the bus_iommu_probe() call-path to make sure it ignores
devices which have already been successfully probed. Then export the
bus_iommu_probe() function so it can be used by IOMMU drivers.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200429133712.31431-14-joro@8bytes.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
After the previous changes the iommu group may not have a default
domain when iommu_group_add_device() is called. With no default domain
iommu_group_create_direct_mappings() will do nothing and no direct
mappings will be created.
Rename iommu_group_create_direct_mappings() to
iommu_create_device_direct_mappings() to better reflect that the
function creates direct mappings only for one device and not for all
devices in the group. Then move the call to the places where a default
domain actually exists.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200429133712.31431-13-joro@8bytes.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
When a bus is initialized with iommu-ops, all devices on the bus are
scanned and iommu-groups are allocated for them, and each groups will
also get a default domain allocated.
Until now this happened as soon as the group was created and the first
device added to it. When other devices with different default domain
requirements were added to the group later on, the default domain was
re-allocated, if possible.
This resulted in some back and forth and unnecessary allocations, so
change the flow to defer default domain allocation until all devices
have been added to their respective IOMMU groups.
The default domains are allocated for newly allocated groups after
each device on the bus is handled and was probed by the IOMMU driver.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200429133712.31431-12-joro@8bytes.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This makes it easier to remove to old code-path when all drivers are
converted. As a side effect that it also fixes the error cleanup
path.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200429133712.31431-11-joro@8bytes.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This is needed to defer default_domain allocation for new IOMMU groups
until all devices have been added to the group.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200429133712.31431-10-joro@8bytes.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Well, not really. The call to iommu_alloc_default_domain() in
iommu_group_get_for_dev() has to stay around as long as there are
IOMMU drivers using the add/remove_device() call-backs instead of
probe/release_device().
Those drivers expect that iommu_group_get_for_dev() returns the device
attached to a group and the group set up with a default domain (and
the device attached to the groups current domain).
But when all drivers are converted this compatability mess can be
removed.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200429133712.31431-9-joro@8bytes.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Add call-backs to 'struct iommu_ops' as an alternative to the
add_device() and remove_device() call-backs, which will be removed when
all drivers are converted.
The new call-backs will not setup IOMMU groups and domains anymore,
so also add a probe_finalize() call-back where the IOMMU driver can do
per-device setup work which require the device to be set up with a
group and a domain.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200429133712.31431-8-joro@8bytes.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
When check_device() fails on the device, it is not handled by the
IOMMU and amd_iommu_add_device() needs to return -ENODEV.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Link: https://lore.kernel.org/r/20200429133712.31431-7-joro@8bytes.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The check was only needed for the DMA-API implementation in the AMD
IOMMU driver, which no longer exists.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Link: https://lore.kernel.org/r/20200429133712.31431-6-joro@8bytes.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The Intel VT-d driver already has a matching function to determine the
default domain type for a device. Wire it up in intel_iommu_ops.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20200429133712.31431-5-joro@8bytes.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Some devices are reqired to use a specific type (identity or dma)
of default domain when they are used with a vendor iommu. When the
system level default domain type is different from it, the vendor
iommu driver has to request a new default domain with
iommu_request_dma_domain_for_dev() and iommu_request_dm_for_dev()
in the add_dev() callback. Unfortunately, these two helpers only
work when the group hasn't been assigned to any other devices,
hence, some vendor iommu driver has to use a private domain if
it fails to request a new default one.
This adds def_domain_type() callback in the iommu_ops, so that
any special requirement of default domain for a device could be
aware by the iommu generic layer.
Signed-off-by: Sai Praneeth Prakhya <sai.praneeth.prakhya@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
[ jroedel@suse.de: Added iommu_get_def_domain_type() function and use
it to allocate the default domain ]
Co-developed-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200429133712.31431-3-joro@8bytes.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Move the code out of iommu_group_get_for_dev() into a separate
function.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200429133712.31431-2-joro@8bytes.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The function qcom_iommu_device_probe() does not perform sufficient
error checking after executing devm_ioremap_resource(), which can
result in crashes if a critical error path is encountered.
Fixes: 0ae349a0f3 ("iommu/qcom: Add qcom_iommu")
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200418134703.1760-1-tangbin@cmss.chinamobile.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
In commit a7ba5c3d00 ("drivers/iommu: Export core IOMMU API symbols to
permit modular drivers") a bunch of iommu symbols were exported, all
with _GPL markings except iommu_group_get_for_dev(). That export should
also be _GPL like the others.
Fixes: a7ba5c3d00 ("drivers/iommu: Export core IOMMU API symbols to permit modular drivers")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Will Deacon <will@kernel.org>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: John Garry <john.garry@huawei.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20200430120120.2948448-1-gregkh@linuxfoundation.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The CONFIG_ prefix should be added in the code.
Fixes: 046182525d ("iommu/vt-d: Add Kconfig option to enable/disable scalable mode")
Reported-and-tested-by: Kumar, Sanjay K <sanjay.k.kumar@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Link: https://lore.kernel.org/r/20200501072427.14265-1-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Currently, system fails to boot because the legacy interrupt remapping
mode does not enable 128-bit IRTE (GA), which is required for x2APIC
support.
Fix by using AMD_IOMMU_GUEST_IR_LEGACY_GA mode when booting with
kernel option amd_iommu_intr=legacy instead. The initialization
logic will check GASup and automatically fallback to using
AMD_IOMMU_GUEST_IR_LEGACY if GA mode is not supported.
Fixes: 3928aa3f57 ("iommu/amd: Detect and enable guest vAPIC support")
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Link: https://lore.kernel.org/r/1587562202-14183-1-git-send-email-suravee.suthikulpanit@amd.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Although SPAPR_TCE_IOMMU itself can be compile tested on certain PowerPC
configurations, its presence makes arch/powerpc/kvm/Makefile to select
modules which do not build in such configuration.
The arch/powerpc/kvm/ modules use kvm_arch.spapr_tce_tables which exists
only with CONFIG_PPC_BOOK3S_64. However these modules are selected when
COMPILE_TEST and SPAPR_TCE_IOMMU are chosen leading to build failures:
In file included from arch/powerpc/include/asm/book3s/64/mmu-hash.h:20:0,
from arch/powerpc/kvm/book3s_64_vio_hv.c:22:
arch/powerpc/include/asm/book3s/64/pgtable.h:17:0: error: "_PAGE_EXEC" redefined [-Werror]
#define _PAGE_EXEC 0x00001 /* execute permission */
In file included from arch/powerpc/include/asm/book3s/32/pgtable.h:8:0,
from arch/powerpc/include/asm/book3s/pgtable.h:8,
from arch/powerpc/include/asm/pgtable.h:18,
from include/linux/mm.h:95,
from arch/powerpc/include/asm/io.h:29,
from include/linux/io.h:13,
from include/linux/irq.h:20,
from arch/powerpc/include/asm/hardirq.h:6,
from include/linux/hardirq.h:9,
from include/linux/kvm_host.h:7,
from arch/powerpc/kvm/book3s_64_vio_hv.c:12:
arch/powerpc/include/asm/book3s/32/hash.h:29:0: note: this is the location of the previous definition
#define _PAGE_EXEC 0x200 /* software: exec allowed */
Fixes: e93a1695d7 ("iommu: Enable compile testing for some of drivers")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200414142630.21153-1-krzk@kernel.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
If NO_DMA=y (e.g. Sun-3 all{mod,yes}-config):
drivers/iommu/dma-iommu.o: In function `iommu_dma_mmap':
dma-iommu.c:(.text+0x836): undefined reference to `dma_pgprot'
IOMMU_DMA must not be selected, unless HAS_DMA=y.
Hence fix this by making MTK_IOMMU depend on HAS_DMA.
While at it, remove the dependency on ARM || ARM64, as that is already
implied by the dependency on ARCH_MEDIATEK.
Fixes: e93a1695d7 ("iommu: Enable compile testing for some of drivers")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/20200410143047.19691-1-geert@linux-m68k.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
In the future the bus sysdata may not directly point to the
zpci_dev.
In preparation of upcoming patches let us abstract the
access to the zpci_dev from the device inside the pci device.
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
The single atomic pool is allocated from the lowest zone possible since
it is guaranteed to be applicable for any DMA allocation.
Devices may allocate through the DMA API but not have a strict reliance
on GFP_DMA memory. Since the atomic pool will be used for all
non-blockable allocations, returning all memory from ZONE_DMA may
unnecessarily deplete the zone.
Provision for multiple atomic pools that will map to the optimal gfp
mask of the device.
When allocating non-blockable memory, determine the optimal gfp mask of
the device and use the appropriate atomic pool.
The coherent DMA mask will remain the same between allocation and free
and, thus, memory will be freed to the same atomic pool it was allocated
from.
__dma_atomic_pool_init() will be changed to return struct gen_pool *
later once dynamic expansion is added.
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Make use of dev_iommu_priv_set/get() functions and simplify the code
where possible with this change.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Tested-by: Will Deacon <will@kernel.org> # arm-smmu
Link: https://lore.kernel.org/r/20200326150841.10083-12-joro@8bytes.org
In preparation for restructuring iommu_fwspec, refactor the way we
access the arm_smmu_master_cfg private data to be less dependent on
the current layout.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Link: https://lore.kernel.org/r/20200326150841.10083-11-joro@8bytes.org
Make use of dev_iommu_priv_set/get() functions in the code.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Tested-by: Hanjun Guo <guohanjun@huawei.com>
Reviewed-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Link: https://lore.kernel.org/r/20200326150841.10083-10-joro@8bytes.org
Some unrelated changes in the iommu code caused a new warning to
appear in the arm-smmu driver:
CC drivers/iommu/arm-smmu.o
drivers/iommu/arm-smmu.c: In function 'arm_smmu_add_device':
drivers/iommu/arm-smmu.c:1441:2: warning: 'smmu' may be used uninitialized in this function [-Wmaybe-uninitialized]
arm_smmu_rpm_put(smmu);
^~~~~~~~~~~~~~~~~~~~~~
The warning is a false positive, but initialize the variable to NULL
to get rid of it.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Tested-by: Will Deacon <will@kernel.org> # arm-smmu
Reviewed-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Link: https://lore.kernel.org/r/20200326150841.10083-8-joro@8bytes.org
Move the iommu_fwspec pointer in struct device into struct dev_iommu.
This is a step in the effort to reduce the iommu related pointers in
struct device to one.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Tested-by: Will Deacon <will@kernel.org> # arm-smmu
Reviewed-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20200326150841.10083-7-joro@8bytes.org
We don't currently support IOMMUs with a page granule larger than the
system page size. The IOVA allocator has a BUG_ON() in this case, and
VFIO has a WARN_ON().
Removing these obstacles ranges doesn't seem possible without major
changes to the DMA API and VFIO. Some callers of iommu_map(), for
example, want to map multiple page-aligned regions adjacent to each
others for scatter-gather purposes. Even in simple DMA API uses, a call
to dma_map_page() would let the endpoint access neighbouring memory. And
VFIO users cannot ensure that their virtual address buffer is physically
contiguous at the IOMMU granule.
Rather than triggering the IOVA BUG_ON() on mismatched page sizes, abort
the vdomain finalise() with an error message. We could simply abort the
viommu probe(), but an upcoming extension to virtio-iommu will allow
setting different page masks for each endpoint.
Reported-by: Bharat Bhushan <bbhushan2@marvell.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Bharat Bhushan <bbhushan2@marvell.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/20200326093558.2641019-4-jean-philippe@linaro.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Calling viommu_domain_free() on a domain that hasn't been finalised (not
attached to any device, for example) can currently cause an Oops,
because we attempt to call ida_free() on ID 0, which may either be
unallocated or used by another domain.
Only initialise the vdomain->viommu pointer, which denotes a finalised
domain, at the end of a successful viommu_domain_finalise().
Fixes: edcd69ab9a ("iommu: Add virtio-iommu driver")
Reported-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/20200326093558.2641019-3-jean-philippe@linaro.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
IOASID code is needed by VT-d scalable mode for PASID allocation.
Add explicit dependency such that IOASID is built-in whenever Intel
IOMMU is enabled.
Otherwise, aux domain code will fail when IOMMU is built-in and IOASID
is compiled as a module.
Fixes: 59a623374d ("iommu/vt-d: Replace Intel specific PASID allocator with IOASID")
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Move canonical address check before mmget_not_zero() to avoid mm
reference leak.
Fixes: 9d8c3af316 ("iommu/vt-d: IOMMU Page Request needs to check if address is canonical.")
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Hanna Hawa