The usage of USB_CTRL_SET_TIMEOUT in xhci is incorrect.
The definition of USB_CTRL_SET_TIMEOUT is 5000ms. The
input timeout to wait_for_completion_interruptible_timeout
is jiffies. That makes the timeout be longer than what
we want, such as 50s in some platform.
The patch is to use XHCI_CMD_DEFAULT_TIMEOUT instead of
USB_CTRL_SET_TIMEOUT as command completion event timeout.
Signed-off-by: xiao jin <jin.xiao@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The USB core currently handles enabling and disabling optional USB power
management features during device transitions (device suspend/resume,
driver bind/unbind, device reset, and device disconnect). Those
optional power features include Latency Tolerance Messaging (LTM),
USB 3.0 Link PM, and USB 2.0 Link PM.
The USB core currently enables LPM on device enumeration and disables
USB 2.0 Link PM when the device is reset. However, the xHCI driver
disables LPM when the device is disconnected and the device context is
freed. Push the call up into the USB core, in order to be consistent
with the core handling all power management enabling and disabling.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
How it's supposed to work:
--------------------------
USB 2.0 Link PM is a lower power state that some newer USB 2.0 devices
support. USB 3.0 devices certified by the USB-IF are required to
support it if they are plugged into a USB 2.0 only port, or a USB 2.0
cable is used. USB 2.0 Link PM requires both a USB device and a host
controller that supports USB 2.0 hardware-enabled LPM.
USB 2.0 Link PM is designed to be enabled once by software, and the host
hardware handles transitions to the L1 state automatically. The premise
of USB 2.0 Link PM is to be able to put the device into a lower power
link state when the bus is idle or the device NAKs USB IN transfers for
a specified amount of time.
...but hardware is broken:
--------------------------
It turns out many USB 3.0 devices claim to support USB 2.0 Link PM (by
setting the LPM bit in their USB 2.0 BOS descriptor), but they don't
actually implement it correctly. This manifests as the USB device
refusing to respond to transfers when it is plugged into a USB 2.0 only
port under the Haswell-ULT/Lynx Point LP xHCI host.
These devices pass the xHCI driver's simple test to enable USB 2.0 Link
PM, wait for the port to enter L1, and then bring it back into L0. They
only start to break when L1 entry is interleaved with transfers.
Some devices then fail to respond to the next control transfer (usually
a Set Configuration). This results in devices never enumerating.
Other mass storage devices (such as a later model Western Digital My
Passport USB 3.0 hard drive) respond fine to going into L1 between
control transfers. They ACK the entry, come out of L1 when the host
needs to send a control transfer, and respond properly to those control
transfers. However, when the first READ10 SCSI command is sent, the
device NAKs the data phase while it's reading from the spinning disk.
Eventually, the host requests to put the link into L1, and the device
ACKs that request. Then it never responds to the data phase of the
READ10 command. This results in not being able to read from the drive.
Some mass storage devices (like the Corsair Survivor USB 3.0 flash
drive) are well behaved. They ACK the entry into L1 during control
transfers, and when SCSI commands start coming in, they NAK the requests
to go into L1, because they need to be at full power.
Not all USB 3.0 devices advertise USB 2.0 link PM support. My Point
Grey USB 3.0 webcam advertises itself as a USB 2.1 device, but doesn't
have a USB 2.0 BOS descriptor, so we don't enable USB 2.0 Link PM. I
suspect that means the device isn't certified.
What do we do about it?
-----------------------
There's really no good way for the kernel to test these devices.
Therefore, the kernel needs to disable USB 2.0 Link PM by default, and
distros will have to enable it by writing 1 to the sysfs file
/sys/bus/usb/devices/../power/usb2_hardware_lpm. Rip out the xHCI Link
PM test, since it's not sufficient to detect these buggy devices, and
don't automatically enable LPM after the device is addressed.
This patch should be backported to kernels as old as 3.11, that
contain the commit a558ccdcc7 "usb: xhci:
add USB2 Link power management BESL support". Without this fix, some
USB 3.0 devices will not enumerate or work properly under USB 2.0 ports
on Haswell-ULT systems.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
To enable USB 2.0 Link Power Management (LPM), the xHCI host controller
needs the device slot ID to generate the device address used in L1 entry
tokens. That information is set in the L1 device slot ID field of the
USB 2.0 LPM registers.
Currently, the L1 device slot ID is overwritten when the xHCI driver
initiates the software test of USB 2.0 Link PM in
xhci_usb2_software_lpm_test. It is never cleared when USB 2.0 Link PM
is disabled for the device. That should be harmless, because the
Hardware LPM Enable (HLE) bit is cleared when USB 2.0 Link PM is
disabled, so the host should not pay attention to the slot ID.
This patch should have no effect on host behavior, but since
xhci_usb2_software_lpm_test is going away in an upcoming bug fix patch,
we need to move that code to the function that enables and disables USB
2.0 Link PM.
This patch should be backported to kernels as old as 3.11, that contain
the commit a558ccdcc7 "usb: xhci: add USB2
Link power management BESL support". The upcoming bug fix patch is also
marked for that stable kernel.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
If a command on the command ring needs to be cancelled before it is handled
it can be turned to a no-op operation when the ring is stopped.
We want to store the command ring enqueue pointer in the command structure
when the command in enqueued for the cancellation case.
Some commands used to store the command ring dequeue pointers instead of enqueue
(these often worked because enqueue happends to equal dequeue quite often)
Other commands correctly used the enqueue pointer but did not check if it pointed
to a valid trb or a link trb, this caused for example stop endpoint command to timeout in
xhci_stop_device() in about 2% of suspend/resume cases.
This should also solve some weird behavior happening in command cancellation cases.
This patch is based on a patch submitted by Sarah Sharp to linux-usb, but
then forgotten:
http://marc.info/?l=linux-usb&m=136269803207465&w=2
This patch should be backported to kernels as old as 3.7, that contain
the commit b92cc66c04 "xHCI: add aborting
command ring function"
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
If a USB controller with XHCI_RESET_ON_RESUME goes to runtime suspend,
a reset will be performed upon runtime resume. Any previously suspended
devices attached to the controller will be re-enumerated at this time.
This will cause problems, for example, if an open system call on the
device triggered the resume (the open call will fail).
Note that this change is only relevant when persist_enabled is not set
for USB devices.
This patch should be backported to kernels as old as 3.0, that
contain the commit c877b3b2ad "xhci: Add
reset on resume quirk for asrock p67 host".
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
Hi Greg,
This is the first of three steps to fix your usb-linus and usb-next
trees. As I mentioned, commit 4fae6f0fa8
"USB: handle LPM errors during device suspend correctly" was incorrectly
added to usb-next when it should have been added to usb-linus and marked
for stable.
Two port power off bug fixes touch the same code that patch touches, but
it's not easy to simply move commit 4fae6f0f patch to usb-linus because
commit 28e861658e "USB: refactor code for
enabling/disabling remote wakeup" also touched those code sections.
I propose a two step process to fix this:
1. Pull these four patches into usb-linus.
2. Revert commit 28e861658e from usb-next.
Merge usb-linus into usb-next, and resolve the conflicts.
I will be sending pull requests for these steps.
This pull request is step one, and contains the backported version of
commit 4fae6f0fa8, the two port power off
fixes, and an unrelated xhci-plat bug fix.
Sarah Sharp
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJSDXUgAAoJEBMGWMLi1Gc5KrcP/jVYFI7CRS9sRWaBxtMdAbi7
Ve0q7479ZmPA9o+SwGKVzO8cM8XJ6mb6CmNww6rByxneUFKvcnq0dwWBc31mZltP
+zYzgOKk0GwAYZ644QvpcZfh8lh/ex52qdPb+RKZIfcsmKJzPJwHJSaYUh+LJrTC
NxW4NqWYSMbroh3X0nsvM4bw/vEP2D8BhMjXrBDcDDC9gkj+YGE3eIeW08Hq47x1
Hil6rA0/BERWvKP5SJdgWdRld6z5NzrOMdOea9LJtHTzrhi9Gyvc2hul4cvKfj4P
VMUslkxw2x13oqeY0xp/uCZkIMYGmvHf50BOGjIoRW8JARe92Vh3mb6xE+ywu4LQ
pHWDDH+ANUtrtNEF1/3xu+8mYNgg5prdhKRztkUlzJ/FTvNPjbYAN+t4p0s3O8bh
VRo6iH9G0pydjVpo1YERX1S69noyUHsguXkrZnMPVMfMC7reOAb5mev56hcSjh9Y
S24RYVHYhJNz9A4L8Y7yDu7Z1MorcIvviTI0xa0AS7n2r40vnEQJtQyP2GbK7KZH
iHIUNh2E6GHyCsvDBMuYgIELJM0OswCiF+SKtMiGgwlbOcVvXMXcgNdCSuMJhuo9
PjNT9bs6RsgSEqYemYruFkhomhPBJHPwTr8dy4YsThx2GOTm0AsZ0FCbVmNPqOvI
1NYgwzvX3fr94iNt3xdg
=0/wL
-----END PGP SIGNATURE-----
Merge tag 'for-usb-2013-08-15-step-1' into for-usb-next
xhci: Step 1 to fix usb-linus and usb-next.
Hi Greg,
This is the first of three steps to fix your usb-linus and usb-next
trees. As I mentioned, commit 4fae6f0fa8
"USB: handle LPM errors during device suspend correctly" was incorrectly
added to usb-next when it should have been added to usb-linus and marked
for stable.
Two port power off bug fixes touch the same code that patch touches, but
it's not easy to simply move commit 4fae6f0f patch to usb-linus because
commit 28e861658e "USB: refactor code for
enabling/disabling remote wakeup" also touched those code sections.
I propose a two step process to fix this:
1. Pull these four patches into usb-linus.
2. Revert commit 28e861658e from usb-next.
Merge usb-linus into usb-next, and resolve the conflicts.
I will be sending pull requests for these steps.
This pull request is step one, and contains the backported version of
commit 4fae6f0fa8, the two port power off
fixes, and an unrelated xhci-plat bug fix.
Sarah Sharp
Resolved conflicts:
drivers/usb/core/hub.c
Hi Greg,
This pull request includes one new feature for the xhci-plat driver (device
tree support). Felipe was fine with the patch last I checked, but hadn't
provided an official Acked-by line.
This pull request also includes 13 patches from my FOSS Outreach Program for
Women (OPW) intern, Xenia. She fixed a bug in the xHCI driver so that the
driver can allocate 64-bit consistent DMA, converted the driver to use dynamic
debugging, and added a bunch of new trace events for the xHCI driver. The
python plugin for trace-cmd should be up on git hub shortly, although the trace
events are usable without it.
I'm very happy with the progress that Xenia has made, and I look forward to her
future contributions to the Linux kernel.
Sarah Sharp
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=n45I
-----END PGP SIGNATURE-----
Merge tag 'for-usb-next-2013-08-15' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-next
Sarah writes:
xhci: Platform updates, 64-bit DMA, and trace events for 3.12.
Hi Greg,
This pull request includes one new feature for the xhci-plat driver (device
tree support). Felipe was fine with the patch last I checked, but hadn't
provided an official Acked-by line.
This pull request also includes 13 patches from my FOSS Outreach Program for
Women (OPW) intern, Xenia. She fixed a bug in the xHCI driver so that the
driver can allocate 64-bit consistent DMA, converted the driver to use dynamic
debugging, and added a bunch of new trace events for the xHCI driver. The
python plugin for trace-cmd should be up on git hub shortly, although the trace
events are usable without it.
I'm very happy with the progress that Xenia has made, and I look forward to her
future contributions to the Linux kernel.
Sarah Sharp
The xHCI platform driver calls into usb_add_hcd to register the irq for
its platform device. It does not want the xHCI generic driver to
register an interrupt for it at all. The original code did that by
setting the XHCI_BROKEN_MSI quirk, which tells the xHCI driver to not
enable MSI or MSI-X for a PCI host.
Unfortunately, if CONFIG_PCI is enabled, and CONFIG_USB_DW3 is enabled,
the xHCI generic driver will attempt to register a legacy PCI interrupt
for the xHCI platform device in xhci_try_enable_msi(). This will result
in a bogus irq being registered, since the underlying device is a
platform_device, not a pci_device, and thus the pci_device->irq pointer
will be bogus.
Add a new quirk, XHCI_PLAT, so that the xHCI generic driver can
distinguish between a PCI device that can't handle MSI or MSI-X, and a
platform device that should not have its interrupts touched at all.
This quirk may be useful in the future, in case other corner cases like
this arise.
This patch should be backported to kernels as old as 3.9, that
contain the commit 00eed9c814 "USB: xhci:
correctly enable interrupts".
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Yu Y Wang <yu.y.wang@intel.com>
Tested-by: Yu Y Wang <yu.y.wang@intel.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Cc: stable@vger.kernel.org
The function dma_set_mask() tests internally whether the dma_mask pointer
for the device is initialized and fails if the dma_mask pointer is NULL.
On pci platforms, the device dma_mask pointer is initialized, when pci
devices are enumerated, to point to the pci_dev->dma_mask which is 0xffffffff.
However, for non-pci platforms, the dma_mask pointer may not be initialized
and in that case dma_set_mask() will fail.
This patch initializes the dma_mask and the coherent_dma_mask to 32bits
in xhci_plat_probe(), before the call to usb_create_hcd() that sets the
"uses_dma" flag for the usb bus and the call to usb_add_hcd() that creates
coherent dma pools for the usb hcd.
Moreover, a call to dma_set_mask() does not set the device coherent_dma_mask.
Since the xhci-hcd driver calls dma_alloc_coherent() and dma_pool_alloc()
to allocate consistent DMA memory blocks, the coherent DMA address mask
has to be set explicitly.
This patch sets the coherent_dma_mask to 64bits in xhci_gen_setup() when
the xHC is capable for 64-bit DMA addressing.
If dma_set_mask() succeeds, for a given bitmask, it is guaranteed that
the given bitmask is also supported for consistent DMA mappings.
Other changes introduced in this patch are:
- The return value of dma_set_mask() is checked to ensure that the required
dma bitmask conforms with the host system's addressing capabilities.
- The dma_mask setup code for the non-primary hcd was removed since both
primary and non-primary hcd refer to the same generic device whose
dma_mask and coherent_dma_mask are already set during the setup of
the primary hcd.
- The code for reading the HCCPARAMS register to find out the addressing
capabilities of xHC was removed since its value is already cached in
xhci->hccparams.
- hcd->self.controller was replaced with the dev variable since it is
already available.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch defines a new trace event, which is called xhci_dbg_init
and belongs to the event class xhci_log_msg, and adds tracepoints that
trace the debug statements in the functions used to start and stop the
xhci-hcd driver.
Also, it removes an unnecessary cast of variable val to unsigned int
in xhci_mem_init(), since val is already declared as unsigned int.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch defines a new trace event, which is called xhci_dbg_cancel_urb
and belongs to the event class xhci_log_msg, and adds tracepoints that
trace the debug messages related to the removal of a cancelled URB from
the endpoint's transfer ring.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch defines a new event class, called xhci_log_ctx,
that records in the ring buffer the context data, the
context type (input or output), the context dma and virtual
addresses, the context endpoint entries, the slot ID and
whether the xHC uses 64 byte context data structures.
This information can be used, later, to parse and display
the context data fields with the appropriate plugin using
the trace-cmd tool.
Also, this patch defines a trace event, called xhci_address_ctx,
to trace the contexts related to the Address Device command and
adds the associated tracepoints in xhci_address_device().
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch defines a new trace event, which is called xhci_dbg_reset_ep
and belongs in the event class xhci_log_msg, and adds tracepoints that
trace the debug messages associated with resetting an endpoint after
the reception of a STALL packet.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch defines a new trace event, which is called xhci_dbg_quirks
and belongs in the event class xhci_log_msg, and adds tracepoints that
trace the debug messages associated with xHCs' quirks.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch defines a new trace event, which is called xhci_dbg_context_change
and belongs in the event class xhci_log_msg, and adds tracepoints for tracing
the debug messages related to context updates performed with Configure Endpoint
and Evaluate Context commands.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch declares an event class for trace events that
trace messages with variadic arguments, called xhci_log_msg,
and defines a trace event for tracing the debug messages in
xhci_address_device() function, called xhci_dbg_address.
In order to implement this type of trace events, a wrapper function,
called xhci_dbg_trace(), was created that records the format string
and variadic arguments into a va_format structure which is passed as
argument to the tracepoints of the class xhci_log_msg.
All the xhci_dbg() calls in xhci_address_device() are replaced
with calls to xhci_dbg_trace(). The functionality of xhci_dbg()
log messages was not removed though, but it is placed inside
xhci_dbg_trace().
This trace event aims to give the ability to the user or the
developper to isolate and trace the debug messages generated
when an Address Device Command is issued to xHC.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
CONFIG_USB_XHCI_HCD_DEBUGGING option is used to enable
verbose debugging output for the xHCI host controller
driver.
In the current version of the xhci-hcd driver, this
option must be turned on, in order for the debugging
log messages to be displayed, and users may need to
recompile the linux kernel to obtain debugging
information that will help them track down problems.
This patch removes the above debug option to enable
debugging log messages at all times.
The aim of this is to rely on the debugfs and the
dynamic debugging feature for fine-grained management
of debugging messages and to not force users to set
the debug config option and compile the linux kernel
in order to have access in that information.
This patch, also, removes the XHCI_DEBUG symbol and the
functions dma_to_stream_ring(), xhci_test_radix_tree()
and xhci_event_ring_work() that are not useful anymore.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch replaces the calls to printk(KERN_DEBUG ...)
with either calls to xhci_dbg() or calls to pr_debug(),
depending on whether the xhci_hcd structure is available
at callsite, so that the correspoding debugging messages
are not enabled by default when CONFIG_DYNAMIC_DEBUG option
is set but rather can be enabled dynamically taking advantage
of the dynamic debugging feature.
Also, it adds a newline at the end of debugging messages in
case there is not, so that messages don't appear broken
when printed.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch replaces the calls to xhci_info() with calls to
xhci_dbg() and removes the unused xhci_info() definition
from xhci-hcd.
By replacing the xhci_info() with xhci_dbg(), the calls to
dev_info() are replaced with calls to dev_dbg() so that
their output can be dynamically controlled via the dynamic
debugging mechanism.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch marks all xHCI controllers as no_sg_constraint
since xHCI supports building packet from discontinuous buffers.
Cc: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A randconfig build hit the following build errors because xhci.c and
xhci-mem.c use dma mapping functions but don't include
<linux/dma-mapping.h>. Add the missing includes to fix the build errors.
drivers/usb/host/xhci.c In function 'xhci_gen_setup':
drivers/usb/host/xhci.c +4872 : error: implicit declaration of function 'dma_set_mask'
drivers/usb/host/xhci.c +4872 : error: implicit declaration of function 'DMA_BIT_MASK'
drivers/usb/host/xhci-mem.c In function 'xhci_free_stream_ctx':
drivers/usb/host/xhci-mem.c +435 : error: implicit declaration of function 'dma_free_coherent'
drivers/usb/host/xhci-mem.c In function 'xhci_alloc_stream_ctx':
drivers/usb/host/xhci-mem.c +463 : error: implicit declaration of function 'dma_alloc_coherent'
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Xhci controllers with hci_version > 0.96 gives spurious success
events on short packet completion. During webcam capture the
"ERROR Transfer event TRB DMA ptr not part of current TD" was observed.
The same application works fine with synopsis controllers hci_version 0.96.
The same issue is seen with Intel Pantherpoint xhci controller. So enabling
this quirk in xhci_gen_setup if controller verion is greater than 0.96.
For xhci-pci move the quirk to much generic place xhci_gen_setup.
Note from Sarah:
The xHCI 1.0 spec changed how hardware handles short packets. The HW
will notify SW of the TRB where the short packet occurred, and it will
also give a successful status for the last TRB in a TD (the one with the
IOC flag set). On the second successful status, that warning will be
triggered in the driver.
Software is now supposed to not assume the TD is not completed until it
gets that last successful status. That means we have a slight race
condition, although it should have little practical impact. This patch
papers over that issue.
It's on my long-term to-do list to fix this race condition, but it is a
much more involved patch that will probably be too big for stable. This
patch is needed for stable to avoid serious log spam.
This patch should be backported to kernels as old as 3.0, that
contain the commit ad808333d8 "Intel xhci:
Ignore spurious successful event."
The patch will have to be modified for kernels older than 3.2, since
that kernel added the xhci_gen_setup function for xhci platform devices.
The correct conflict resolution for kernels older than 3.2 is to set
XHCI_SPURIOUS_SUCCESS in xhci_pci_quirks for all xHCI 1.0 hosts.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
Resolves the following build warnings:
drivers/usb/host/xhci.c:332:13: warning: 'xhci_msix_sync_irqs' defined but not used [-Wunused-function]
drivers/usb/host/xhci.c:3901:12: warning: 'xhci_change_max_exit_latency' defined but not used [-Wunused-function]
These functions are not always used, and since they're marked static
they will produce build warnings:
- xhci_msix_sync_irqs is only used with CONFIG_PCI.
- xhci_change_max_exit_latency is a little more complicated with
dependencies on CONFIG_PM and CONFIG_PM_RUNTIME.
Instead of building a bigger maze of ifdefs in this code, I've just
marked both with __maybe_unused.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
When the host controller fails to respond to an Enable Slot command, and
the host fails to respond to the register write to abort the command
ring, the xHCI driver will assume the host is dead, and call
usb_hc_died().
The USB device's slot_id is still set to zero, and the pointer stored at
xhci->devs[0] will always be NULL. The call to xhci_check_args in
xhci_free_dev should have caught the NULL virt_dev pointer.
However, xhci_free_dev is designed to free the xhci_virt_device
structures, even if the host is dead, so that we don't leak kernel
memory. xhci_free_dev checks the return value from the generic
xhci_check_args function. If the return value is -ENODEV, it carries on
trying to free the virtual device.
The issue is that xhci_check_args looks at the host controller state
before it looks at the xhci_virt_device pointer. It will return -ENIVAL
because the host is dead, and xhci_free_dev will ignore the return
value, and happily dereference the NULL xhci_virt_device pointer.
The fix is to make sure that xhci_check_args checks the xhci_virt_device
pointer before it checks the host state.
See https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1203453 for
further details. This patch doesn't solve the underlying issue, but
will ensure we don't see any more NULL pointer dereferences because of
the issue.
This patch should be backported to kernels as old as 3.1, that
contain the commit 7bd89b4017 "xhci: Don't
submit commands or URBs to halted hosts."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Vincent Thiele <vincentthiele@gmail.com>
Cc: stable@vger.kernel.org
Logging messages end in newlines, not have
them put in the middle of messages.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch adds missing unlocks on error paths in the
xhci_free_streams and xhci_configure_endpoint functions.
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fail gracefully, instead of causing the kernel to panic, if the input
control context doesn't have the right type (XHCI_CTX_TYPE_INPUT). Push
finding the pointer to the input control context up into functions that
can fail.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: John Youn <johnyoun@synopsys.com>
Adds abitilty to tune L1 timeout (inactivity timer for usb2 link sleep)
and BESL (best effort service latency)via sysfs.
This also adds a new usb2_lpm_parameters structure with those variables to
struct usb_device.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
usb 2.0 devices with link power managment (LPM) can describe their idle link
timeouts either in BESL or HIRD format, so far xHCI has only supported HIRD but
later xHCI errata add BESL support as well
BESL timeouts need to inform exit latency changes with an evaluate
context command the same way USB 3.0 link PM code does.
The same xhci_change_max_exit_latency() function is used as with USB3
but code is pulled out from #ifdef CONFIG_PM as USB2.0 BESL LPM
funcionality does not depend on CONFIG_PM.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Hardware link powermanagement in usb2 is a per-port capability.
Previously support for hw lpm was enabled for all ports if any usb2 port supported it.
Now instead cache the capability values and check them for each port individually
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
According to Felipe and Alan's comments the second parameter of irq
handler should be 'void *' not a specific structure pointer.
So change it.
Signed-off-by: Alex Shi <alex.shi@intel.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
When CONFIG_XHCI_HCD_DEBUGGING is activated, the XHCI driver can dump
device and input contexts to the console. The endpoint contexts in that
dump are labeled "Endpoint N Context", where N is the XHCI endpoint
index (DCI - 1). This can be very confusing, especially for people who
are not that familiar with the XHCI specification. This patch introduces
an xhci_get_endpoint_address function (as a counterpart to the reverse
xhci_get_endpoint_index), and uses it to additionally display the
endpoint number and direction when dumping contexts, which are much more
commonly used concepts in USB.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Some xHCI hosts contain a "redriver" from TI that silently drops port
status connect changes if the port slips into Compliance Mode. If the
port slips into compliance mode while the host is in D0, there will not
be a port status change event. If the port slips into compliance mode
while the host is in D3, the host will not send a PME. This includes
when the system is suspended (S3) or hibernated (S4).
If this happens when the system is in S3/S4, there is nothing software
can do. Other port status change events that would normally cause the
host to wake the system from S3/S4 may also be lost. This includes
remote wakeup, disconnects and connects on other ports, and overrcurrent
events. A decision was made to _NOT_ disable system suspend/hibernate
on these systems, since users are unlikely to enable wakeup from S3/S4
for the xHCI host.
Software can deal with this issue when the system is in S0. A work
around was put in to poll the port status registers for Compliance Mode.
The xHCI driver will continue to poll the registers while the host is
runtime suspended. Unfortunately, that means we can't allow the PCI
device to go into D3cold, because power will be removed from the host,
and the config space will read as all Fs.
Disable D3cold in the xHCI PCI runtime suspend function.
This patch should be backported to kernels as old as 3.2, that
contain the commit 71c731a296 "usb: host:
xhci: Fix Compliance Mode on SN65LVPE502CP Hardware"
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: stable@vger.kernel.org
Commit 71c731a2 (usb: host: xhci: Fix Compliance Mode on SN65LVPE502CP
Hardware) was a workaround for systems using the SN65LVPE502CP,
controller, but it introduced a bug in resume from hibernate.
The fix created a timer, comp_mode_recovery_timer, which is deleted from
a timer list when xhci_suspend() is called. However, the hibernate image,
including the timer list containing the comp_mode_recovery_timer, had
already been saved before the timer was deleted.
Upon resume from hibernate, the list containing the comp_mode_recovery_timer
is restored from the image saved to disk, and xhci_resume(), assuming that
the timer had been deleted by xhci_suspend(), makes a call to
compliance_mode_recoery_timer_init(), which creates a new instance of the
comp_mode_recovery_timer and attempts to place it into the same list in which
it is already active, thus corrupting the list during the list_add() call.
At this point, a call trace is emitted indicating the list corruption.
Soon afterward, the system locks up, the watchdog times out, and the
ensuing NMI crashes the system.
The problem did not occur when resuming from suspend. In suspend, the
image in RAM remains exactly as it was when xhci_suspend() deleted the
comp_mode_recovery_timer, so there is no problem when xhci_resume()
creates a new instance of this timer and places it in the still empty
list.
This patch avoids the problem by deleting the timer in xhci_resume()
when resuming from hibernate. Now xhci_resume() can safely make the
call to create a new instance of this timer, whether returning from
suspend or hibernate.
Thanks to Alan Stern for his help with understanding the problem.
[Sarah reworked this patch to cover the case where the xHCI restore
register operation fails, and (temp & STS_SRE) is true (and we re-init
the host, including re-init for the compliance mode), but hibernate is
false. The original patch would have caused list corruption in this
case.]
This patch should be backported to kernels as old as 3.2, that
contain the commit 71c731a296 "usb: host:
xhci: Fix Compliance Mode on SN65LVPE502CP Hardware"
Signed-off-by: Tony Camuso <tcamuso@redhat.com>
Tested-by: Tony Camuso <tcamuso@redhat.com>
Acked-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
There are no functional changes in this patch. However, because the
compliance mode timer can be deleted in more than one function, it
seemed expedient to include the function name in the debug strings.
Also limited the use of capitals to the first word in the compliance
mode debug messages, except after a function name where all words
start with lower case, in keeping with the style prevalent elsewhere
in xhci.c.
Signed-off-by: Tony Camuso <tcamuso@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch (as1675) removes the CONFIG_USB_SUSPEND option, essentially
replacing it everywhere with CONFIG_PM_RUNTIME (except for one place
in hub.c, where it is replaced with CONFIG_PM because the code needs
to be used in both runtime and system PM). The net result is code
shrinkage and simplification.
There's very little point in keeping CONFIG_USB_SUSPEND because almost
everybody enables it. The few that don't will find that the usbcore
module has gotten somewhat bigger and they will have to take active
measures if they want to prevent hubs from being runtime suspended.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci driver divides the root hub into two logical hubs which work
respectively for usb 2.0 and usb 3.0 devices. They are independent
devices in the usb core. But in the ACPI table, it's one device node
and all usb2.0 and usb3.0 ports are under it. Binding usb port with
its acpi node needs the raw port number which is reflected in the xhci
extended capabilities table. This patch is to add find_raw_port_number
callback to struct hc_driver(), fill it with xhci_find_raw_port_number()
which will return raw port number and add a wrap usb_hcd_find_raw_port_number().
Otherwise, refactor xhci_find_real_port_number(). Using
xhci_find_raw_port_number() to get real index in the HW port status
registers instead of scanning through the xHCI roothub port array.
This can help to speed up.
All addresses in xhci->usb2_ports and xhci->usb3_ports array are
kown good ports and don't include following bad ports in the extended
capabilities talbe.
(1) root port that doesn't have an entry
(2) root port with unknown speed
(3) root port that is listed twice and with different speeds.
So xhci_find_raw_port_number() will only return port num of good ones
and never touch bad ports above.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
xhci has its own interrupt enabling routine, which will try to
use MSI-X/MSI if present. So the usb core shouldn't try to enable
legacy interrupts; on some machines the xhci legacy IRQ setting
is invalid.
v3: Be careful to not break XHCI_BROKEN_MSI workaround (by trenn)
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Oliver Neukum <oneukum@suse.de>
Cc: Thomas Renninger <trenn@suse.de>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Frederik Himpe <fhimpe@vub.ac.be>
Cc: David Haerdeman <david@hardeman.nu>
Cc: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reviewed-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB core hub thread (khubd) is designed with external USB hubs in
mind. It expects that if a port status change bit is set, the hub will
continue to send a notification through the hub status data transfer.
Basically, it expects hub notifications to be level-triggered.
The xHCI host controller is designed to be edge-triggered on the logical
'OR' of all the port status change bits. When all port status change
bits are clear, and a new change bit is set, the xHC will generate a
Port Status Change Event. If another change bit is set in the same port
status register before the first bit is cleared, it will not send
another event.
This means that the hub code may lose port status changes because of
race conditions between clearing change bits. The user sees this as a
"dead port" that doesn't react to device connects.
The fix is to turn on port polling whenever a new change bit is set.
Once the USB core issues a hub status request that shows that no change
bits are set in any USB ports, turn off port polling.
We can't allow the USB core to poll the roothub for port events during
host suspend because if the PCI host is in D3cold, the port registers
will be all f's. Instead, stop the port polling timer, and
unconditionally restart it when the host resumes. If there are no port
change bits set after the resume, the first call to hub_status_data will
disable polling.
This patch should be backported to stable kernels with the first xHCI
support, 2.6.31 and newer, that include the commit
0f2a79300a "USB: xhci: Root hub support."
There will be merge conflicts because the check for HC_STATE_SUSPENDED
was moved into xhci_suspend in 3.8.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable@vger.kernel.org
that check will have to be done by all users
of xhci_suspend() so it sounds a lot better to
move the check to xhci_suspend() in order to
avoid code duplication.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This minor patch creates a more stricter conditional for the Z1 sytems for applying
the Compliance Mode Patch, this to avoid the quirk to be applied to models that
contain a "Z1" in their dmi product string but are different from Z1 systems.
This patch should be backported to stable kernels as old as 3.2, that
contain the commit 71c731a296 "usb: host:
xhci: Fix Compliance Mode on SN65LVPE502CP Hardware"
Signed-off-by: Alexis R. Cortes <alexis.cortes@ti.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
David reports that at drivers/usb/host/xhci.c:2257:
static bool xhci_is_sync_in_ep(unsigned int ep_type)
{
return (ep_type == ISOC_IN_EP || ep_type != INT_IN_EP);
}
The static analyser cppcheck says
[linux-3.7-rc2/drivers/usb/host/xhci.c:2257]: (style) Redundant condition: If ep_type == 5, the comparison ep_type != 7 is always true.
Maybe the original programmer intention was something like
static bool xhci_is_sync_in_ep(unsigned int ep_type)
{
return (ep_type == ISOC_IN_EP || ep_type == INT_IN_EP);
}
Fix this.
This patch should be backported to stable kernels as old as 3.2, that
contain the commit 2b69899934 "xhci: USB
3.0 BW checking."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: David Binderman <dcb314@hotmail.com>
Cc: stable@vger.kernel.org
Non-static xHCI driver symbols should start with the "xhci_" prefix, in
order to avoid namespace pollution. Rename the "handshake" function to
"xhci_handshake".
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Remove the variable ep_ctx from xhci_add_endpoint(), since it is
assigned but unused. Caught by Coverity.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Coverity complains that xhci_evaluate_context_result() is missing a
break statement after the COMP_EBADSLT switch case. It's not a big
deal, since we wanted to return the same error code as the case
statement below it does. The end result would be one that a Slot
Disabled error completion code would also print the warning message
associated with a Context State error code. No other bad behavior would
result.
It's not worth backporting to stable kernels, since it only fixes an
issue with too much debugging.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
xiao jin