We get the insertion event before the jack is fully inserted at which point
the second ring on a TRRS connector may short the 2nd ring and sleeve
contacts. Testing has shown that this short-circuit may happen as late
as 500ms after the insertion event, but it never lasts longer then 300ms.
This commit changes the detection algorithm to require 5 identical OVCD
values in a row at 100 ms intervals to fix the jack-type sometimes getting
mis-detected.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add rt5651_jack_inserted() helper to get the jack-detect switch status,
This is a preparation patch for rewriting the jack type-detection to
make it more reliable.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When using RCCLK instead of MCLK / PLL1 the OVCD status often gets stuck
at its last value, which breaks jack-type detection.
This commit fixes this by force-enabling the platform clock when doing
jack-type detection.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When the mic-gnd contacts are short-circuited by a headphones plug, the
hardware periodically retries if it can apply the bias-current leading to
the OVCD status flip-flopping 1-0-1 with it being 0 about 10% of the time.
This commit enables the sticky bit for the OVCD status to deal with this.
This commit also introduces 2 helper functions to deal with the OVCD
status bit, this may seem a bit overkill now, but these will also be
used in future patches.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
OVer-Current-Detection (OVCD) for the micbias current is used to detect if
an inserted jack is a headset or headphones (mic shorted to ground).
The threshold for at which current the OVCD triggers on the rt5651 is not
only controlled by setting the absolute current limit, but also by setting
a scale factor which applies to the limit. Testing has shown that we need
to set both (depending on the board).
This commit adds support for the sofar unused OVCD scale-factor register
and adds support for specifying non-default values for it through the
"realtek,over-current-scale-factor" device-property.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
OVer-Current-Detection (OVCD) for the micbias current is used to detect
if an inserted jack is a headset or headphones (mic shorted to ground).
Some boards may need different values for the OVCD current threshold
because of a resistor on the board in serial with or parallel to the
jack mic contact.
This commit adds support for configuring the OCVD current threshold
through the "realtek,over-current-threshold-microamp" device-property.
Note this commit changes the default value from 600uA to 2000uA,
because testing has shown 600uA to be a poor default.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Configure the jack-detect source through a device-property which can be
set by code outside of the codec driver. Rather then putting platform
specific DMI quirks inside the generic codec driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The idea behind exporting rt5651_apply_properties(), was for it to be used
on platforms where the platform code may need to add device-properties,
rather then relying only on properties set by the firmware. The platform
code could then call rt5651_apply_properties() after adding properties to
make sure that the codec driver was aware of the new properties.
But this is not necessary, as long as we do all property parsing from
the codec component-driver's probe function (or later) then the machine
driver can attach properties before calling snd_soc_register_card and
calling rt5651_apply_properties() for ordering reasons is not necessary.
This commit makes rt5651_apply_properties() private and adds 2 comments
documenting that all property parsing must be done from the codec
component-driver's probe function.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The dock line-out pin (NID 0x17 of ALC3254 codec) on Dell Precision
7520 may route to three different DACs, 0x02, 0x03 and 0x06. The
first two DACS have the volume amp controls while the last one
doesn't. And unfortunately, the auto-parser assigns this pin to DAC3,
resulting in the non-working volume control for the line out.
Fix it by disabling the routing to DAC3 on the corresponding pin.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=199029
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The internal mic boost on the T480 is too high. Fix this by applying the
ALC269_FIXUP_LIMIT_INT_MIC_BOOST fixup to the machine to limit the gain.
Signed-off-by: Benjamin Berg <bberg@redhat.com>
Tested-by: Benjamin Berg <bberg@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This platform was only one phone Jack.
Add dummy lineout verb to fix automute mode disable.
This just the workaround.
[ More background information:
since the platform has only a headphone jack without speaker, the
driver doesn't create the auto-mute control. Meanwhile we do update
the headset mode via the automute hook in the driver, thus with this
setup, the headset won't be updated any longer.
By adding a dummy line-out pin here, the auto-mute is added by the
driver, and the headset update is triggered properly.
Note that this is different from the other
ALC274_FIXUP_DELL_AIO_LINEOUT_VERB, which has the real line-out pin,
while this quirk adds a dummy line-out pin. -- tiwai ]
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Driver probe function has no use and can be deleted.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the error: passing argument 1 of 'nau8824_enable_jack_detect'
from incompatible pointer type
nau8824_enable_jack_detect(codec, jack);
^~~~~
Which expects 'struct snd_soc_component *' but argument is of type
'struct snd_soc_codec *'
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With the alc289, the Pin 0x1b is Headphone-Mic, so we should assign
ALC269_FIXUP_DELL4_MIC_NO_PRESENCE rather than
ALC225_FIXUP_DELL1_MIC_NO_PRESENCE to it. And this change is suggested
by Kailang of Realtek and is verified on the machine.
Fixes: 3f2f7c553d ("ALSA: hda - Fix headset mic detection problem for two Dell machines")
Cc: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Module id is a property of firmware manifest and can vary across
platforms. So use the uuid to find module id dynamically for bind
params like kpb post bind params.
Signed-off-by: Sriram Periyasamy <sriramx.periyasamy@intel.com>
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Create BE DAI link for WoV and accordingly update the DAPM machine map
Signed-off-by: Pawse, GuruprasadX <guruprasadx.pawse@intel.com>
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently DMIC capture and WoV usecase uses same BE DAI but operate at
different sampling rates, this results in config mismatch for WoV when
DMIC is already running in parallel.
DMIC has two slots which can operate with some constraints, so add BE
DAI for DMICvoice pin which can used for WoV usecases to capture 4ch,
16KHz, 16bit data.
Signed-off-by: Pawse, GuruprasadX <guruprasadx.pawse@intel.com>
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The current check is not effective when all the widgets of a card are
involved since other widgets also can be of same type. So, make widget
type check more stringent by checking dev pointer additionally.
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With gcc-4.1.2, if CONFIG_SND_SOC_RT5514_SPI is not set:
sound/soc/codecs/rt5514.c: In function ‘rt5514_dsp_voice_wake_up_put’:
sound/soc/codecs/rt5514.c:363: warning: ‘buf[0]’ is used uninitialized in this function
sound/soc/codecs/rt5514.c:363: warning: ‘buf[1]’ is used uninitialized in this function
sound/soc/codecs/rt5514.c:363: warning: ‘buf[2]’ is used uninitialized in this function
sound/soc/codecs/rt5514.c:363: warning: ‘buf[3]’ is used uninitialized in this function
Fix this by initializing the buffer with zeroes, to avoid random bits
being written to the calibration register later.
Fixes: fc9cab0583 ("ASoC: rt5514: The DSP clock can be calibrated by the other clock source")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
rt5514_dsp_voice_wake_up_put() passes "(u8 *)&buf" to
rt5514_spi_burst_read(), where the cast is needed to silence a compiler
warning:
sound/soc/codecs/rt5514.c: In function ‘rt5514_dsp_voice_wake_up_put’:
sound/soc/codecs/rt5514.c:357: warning: passing argument 2 of ‘rt5514_spi_burst_read’ from incompatible pointer type
However, as the variable is declared as an array ("u8 buf[8]"), the
function should just pass "buf" instead.
Fixes: fc9cab0583 ("ASoC: rt5514: The DSP clock can be calibrated by the other clock source")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
OVCD is not only useful for jack-type detection, but is also useful
to protect against over-current faults in general, so always keep
OVCD enabled, instead of only enabling it for jack-type detection.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Only configure OVCD once at set_jack time, rather then configuring
it on every jack-insertion event and switch to using bit field defines
instead of hardcoding a magic value.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To determine if a plugged in jack is a headset (speakers + mic) or
headphones (mic contact shorted to ground) we use the micbias1 OVer Current
Detect (OVCD) functionality.
For this to work we need to have a micbias current to actually cause an
overcurrent condition when headphones are plugged in, so jack-type
detection requires both the LDO and micbias1 supplies to be on.
Before this commit there were 2 issues with the handling of this:
1) The LDO supply was force-enabled twice and never disabled again even
though it only needs to be forced on when doing jack-type detection
2) micbias1 was not force-enabled, and thus may be off when doing jack-type
detection
This commit fixes both by force-enabling the LDO and micbias1 supplies
before checking for an overcurrent condition and disabling them afterwards.
Note that both supplies will still get turned on normally (and OVCD will
protect against overcurrent) when the micbias1 is enabled normally because
the user has activated a sound stream recording from the mic.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove the "JD power" dapm supply which gets force-enabled once when
using jack-detect and never gets disabled again.
Since the PWR_JD_M bit simply needs to be always on when using jack-detect
there is no need to have it tracked by dapm, instead we can simply set it
to 1 once when initializing the jack-detection.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that rt5651_set_bias_level(BIAS_OFF) no longer modifies the LDO
voltage selection bits, there is no need to set them each time we move
to standby. Instead configure them once at component-probe() time.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove the setup of the PWR_ANLG1 reg which was done directly before
calling snd_soc_component_force_bias_level(SND_SOC_BIAS_OFF), as the
latter will override any settings done to PWR_ANLG1 immediately anyways.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rt5651_set_bias_level(BIAS_OFF) used to unconditionally clear the entire
register, including the jack-detect and PLL power bits. When jack-detection
support was introduced a special case for jack-detect was added which
hard-codes a register value to keep both on.
This commit removes the jack-detect special case, instead simply leaving
these bits as is on BIAS_OFF.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The PWR_ANLG1 reg not only contains various power on/off bits, it also
contains 2 bits which select if the LDO generates 1.0, 1.1 or 1.2V. Note
there is a separate on/off bit for the LDO.
rt5651_set_bias_level(BIAS_OFF) used to unconditionally clear the entire
register, when jack-detection support was introduced a special case for
jack-detect was added which hard-codes a register value to keep the LDO
voltage at 1.2 volt.
This commit removes the jack-detect special case, instead simply always
leaving the LDO voltage control bits as is on BIAS_OFF.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The rt5651_set_bias_level() function was turning everything off at
SND_SOC_BIAS_STANDBY, rather then at SND_SOC_BIAS_OFF, requiring the bias-
level to be raised to SND_SOC_BIAS_PREPARE before turning anything on.
This is not how the bias-levels are supposed to work, this commit fixes
this by turning everything off at the SND_SOC_BIAS_OFF level and enabling
the pwr-bits needed for minimum functionality at SND_SOC_BIAS_STANDBY.
This fixes the minimum set of pwr-bits not getting enabled when
force-enabling some dapm-supplies (e.g. for jack type detection),
which raises the bias-level to standby.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
is_sys_clk_from_pll() is used as a snd_soc_dapm_route.connected callback,
checking RT5651_GBL_CLK to determine if the sys-clk is PLL1 and thus the
PWR_PLL bit in reg PWR_ANLG2 must be set.
RT5651_GBL_CLK is changed by rt5651_set_dai_sysclk(), which gets called by
the pre_pmu / post_pmd functions of the "Platform Clock" dapm-supply.
This creates an ordering issue, during a dapm transition first all
connected() callbacks are called to build a list of supplies to enable
and then the complete list is walked to enable the supplies. Since the
connected() check happens before enabling any supplies,
is_sys_clk_from_pll() ends up deciding if the PWR_PLL bit should be set
based on the state the "Platform Clock" supply had *before* the transition.
This sometimes results in PWR_PLL being off, even though *after* the
transition PLL1 is configured as sys-clk.
This commit removes is_sys_clk_from_pll() instead simply setting / clearing
PWR_PLL in rt5651_set_dai_sysclk() based on the selected sys-clk, which
fixes this and as a bonus results in a nice cleanup.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is an error message within devm_ioremap_resource already,
so remove the redundant dev_err() call.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Codes is stereo only with playback and capture streams bind
to the same rate.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Tell user what are clock rate limits and reindent log messages.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move the applying of the differential input and dmic properties to a new
rt5651_apply_properties() helper function. This new function can be called
by platform code which attaches properties after probe() has run to apply
these new properties.
Note this also moves the time when we apply these properties for DT
platforms from i2c-probe to snd-component-probe time, this should not
result in any functional difference.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the standard component set_jack callback instead of defining a codec
private API for this.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move 2 functions higher up in rt5651.c, this is a preparation patch
to avoid needing forward declarations when moving over from a codec
private function to the standard snd_soc_component_set_jack().
This commit purely moves these 2 functions up, not a single line is
changed.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move all jack-detect initialization to rt5651_set_jack_detect. The main
reason to do this is so that platform code can setup jack-detect properties
after the device has been probed, which unfortunately is necessary on some
platforms.
This has 2 additional advantages:
1) Grouping all jack-detect init together makes it easier to follow what
is happening and results in a small reduction in the number of loc.
2) Before we would register the irq handler before rt5651->hp_jack was
assigned, leading to a potential NULL deref if the jack_detect work runs
before the machine driver has called set_jack.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are no in tree users of platform-data for the rt5651 codec driver,
so lets remove support for it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Create sound card with NAU88L24 codec in Intel Cherryview-based platforms,
Cherrytrail and Braswell.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rt5663 requires mclk/sclk early to synchronize its internal clocks.
Enable these clocks early.
Signed-off-by: Naveen Manohar <naveen.m@intel.com>
Signed-off-by: Kevin Cheng <kevin.cheng@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Bay Trail SST-DSP firmware version looses track of all streams over a
suspend/resume, failing any attempts to resume and/or free streams, with
a SST_ERR_INVALID_STREAM_ID error.
This commit adds support for free-ing the streams on suspend and
re-allocating them on resume, fixing suspend/resume issues on devices
using this firmware version.
This new behavior gets triggered by a new flag in sst_platform_info which
only gets set on Bay Trail platforms.
This has been tested on the following devices:
-Asus T100TA, Bay Trail + ALC5642 codec
-Ployer MOMO7W, Bay Trail CR + ALC5652 codec
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move the struct snd_sst_alloc_mrfld alloc parameters from the stack
into struct stream_info and add a new sst_realloc_stream() function which
can re-alloc a stream with the same parameters as before.
This is a preparation patch for fixing suspend/resume issues with some
SST / DSP firmware versions.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
STREAM_DECODE is completely unused, status == STREAM_RESET was checked
for, but never set, remove both.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
sst_init_stream() has only one caller and all its function arguments are
unused. Inline it on the one call site and remove it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove the unused ops and str_id members from the stream_info struct.
While at it also remove some kernel-doc comments for members which have
already been removed in the past.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The value returned by sst_prepare_and_post_msg() is a negated SST_ERR_*
value, so we must check for -SST_ERR_INVALID_STREAM_ID. Note that
sst_pause_resume() already has the correct check.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Replace unsafe usages of strcpy() to copy the name
argument into the sid.name buffer with strlcpy()
to guard against possible buffer overflows.
Signed-off-by: Joey Pabalinas <joeypabalinas@gmail.com>
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Normal 512-byte get/set of a TLV isn't supported but we were
registering the normal get/set anyway and relying on omitting
the SNDRV_CTL_ELEM_ACCESS_[READ|WRITE] flags to prevent them
being called.
Trouble is if this gets broken in the core ALSA code - as it has
been since at least 4.14 - the standard get/set can be called
unexpectedly and corrupt memory.
There's no point providing functions that won't be called and
it's a trivial change. The benefit is that if the ALSA core gets
broken again we get a big fat immediate NULL dereference instead
of a memory corruption timebomb.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
When LPE audio driver gets some error at probing, it may lead to a
crash because of canceling the pending work in hdmi_lpe_audio_free(),
since some of ports might be still not initialized.
For assuring the proper free of each port, initialize all ports at the
beginning of the probe.
Fixes: b4eb0d522f ("ALSA: x86: Split snd_intelhad into card and PCM specific structures")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit change for supporting the multiple ports moved involved
some code shuffling, and there the initializations of spinlock and
mutex in snd_intelhad object were dropped mistakenly.
This patch adds the missing initializations again for each port.
Fixes: b4eb0d522f ("ALSA: x86: Split snd_intelhad into card and PCM specific structures")
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove a bunch of trailing whitespace errors. They are
fairly annoying if you have your editor set to strip trailing
whitespace because you find you've introduced more changes
than you were trying to make.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The patch "ALSA: control: code refactoring for ELEM_READ/ELEM_WRITE
operations" introduced a potential for kernel memory corruption due
to an incorrect if statement allowing non-readable controls to fall
through and call the get function. For TLV controls a driver can omit
SNDRV_CTL_ELEM_ACCESS_READ to ensure that only the TLV get function
can be called. Instead the normal get() can be invoked unexpectedly
and as the driver expects that this will only be called for controls
<= 512 bytes, potentially try to copy >512 bytes into the 512 byte
return array, so corrupting kernel memory.
The problem is an attempt to refactor the snd_ctl_elem_read function
to invert the logic so that it conditionally aborted if the control
is unreadable instead of conditionally executing. But the if statement
wasn't inverted correctly.
The correct inversion of
if (a && !b)
is
if (!a || b)
Fixes: becf9e5d55 ("ALSA: control: code refactoring for ELEM_READ/ELEM_WRITE operations")
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Motorola CPCAP is a PMIC with audio functionality, that can be
found on Motorola Droid 4 and probably a few other phones from
Motorola's Droid series.
The driver has been written from scratch using Motorola's Android
driver, register dumps from running Android and datasheet for NXP
MC13783UG (which is similar to Motorola CPCAP, but not the same).
The chip provides two audio interfaces, that can be muxed to two
different audio codecs. One provides support for stereo output
(named StDAC or HiFi), while the other only provides mono output
(named Voice). Only the Voice codec provides a Capture interface.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support of the ROHM BD28623MUV
Class D speaker amplifier for Flat-panel TVs.
This IC delivers an output power of 20W + 20W.
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
fsl-asoc-card machine driver also handles wm8962, so there is
really no need for keeping the dedicated imx-wm8962 driver anymore.
Remove the imx-wm8962 machine driver.
Suggested-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The show() method should use scnprintf() not snprintf() because snprintf()
may returns a value that exceeds its second argument.
Signed-off-by: Jaejoong Kim <climbbb.kim@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This reverts commit f91b1e73cc.
As explained by Lars-Peter Clausen:
"This creates a resource leak. dmaengine_pcm_request_chan_of() requests
bothtransmit and receive channels. It might return with an error if one
of them fails, but the other one succeeded. In this case we need to call
dmaengine_pcm_release_chan() to free the requested channel"
So revert the commit.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We've added a quirk to enable the recent Lenovo dock support, where it
overwrites the pin configs of NID 0x17 and 19, not only updating the
pin config cache. It works right after the boot, but the problem is
that the pin configs are occasionally cleared when the machine goes to
PM. Meanwhile the quirk writes the pin configs only at the pre-probe,
so this won't be applied any longer.
For addressing that issue, this patch moves the code to overwrite the
pin configs into HDA_FIXUP_ACT_INIT section so that it's always
applied at both probe and resume time.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=195161
Fixes: 61fcf8ece9 ("ALSA: hda/realtek - Enable Thinkpad Dock device for ALC298 platform")
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add support of S/PDIF iec60958 playback on STM32 SAI.
Signed-off-by: olivier moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Allow dmaengine client to optionally register a processing callback.
This callback is intended to apply processing
on samples in buffer copied from/to user space, before/after DMA transfer.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the following sparse warnings are observed:
sound/soc/soc-generic-dmaengine-pcm.c:185:34: warning: restricted snd_pcm_format_t degrades to integer
sound/soc/soc-generic-dmaengine-pcm.c:186:66: warning: incorrect type in argument 1 (different base types)
sound/soc/soc-generic-dmaengine-pcm.c:186:66: expected restricted snd_pcm_format_t [usertype] format
sound/soc/soc-generic-dmaengine-pcm.c:186:66: got int [signed] [assigned] i
Fix it by changing the loop variable to be of 'snd_pcm_format_t'.
Also introduce a SNDRV_PCM_FORMAT_FIRST label, which corresponds to the
first member (index 0) of the snd_pcm_format_t formats.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When dmaengine_pcm_request_chan_of() fails it should release
the previously acquired resources, which in this case is to
call kfree(pcm), so jump to the correct point in the error
path.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Clear the buffer data structure on each trigger start such that the
buffer is in a sensible state even if the DSP itself didn't restart.
This is necessary to support voice control streams which can trigger
multiple times without reloading the firmware.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
I2S's RX slot number of SUN8I should be shifted 4 bit to left.
Fixes: 7d2993811a ("ASoC: sun4i-i2s: Add support for H3")
Signed-off-by: Yong Deng <yong.deng@magewell.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Bit pattern SNDRV_PCM_FMTBIT_S24_LE is being bit-wise or'd twice; remove
the redundant 2nd SNDRV_PCM_FMTBIT_S24_LE
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Bit pattern USP_RXFIFO_THD_INT is being bit-wise or'd twice;
remove the redundant 2nd USP_RXFIFO_THD_INT
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes settings for ports with SRC. These ports need to
set the fixed audio rate and clock. If not, the SRC outputs broken
sound.
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The capture interface doesn't work and the playback interface only
supports 48 kHz sampling rate even though it advertises more rates.
Signed-off-by: Erik Veijola <erik.veijola@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On some boards setting power_save to a non 0 value leads to clicking /
popping sounds when ever we enter/leave powersaving mode. Ideally we would
figure out how to avoid these sounds, but that is not always feasible.
This commit adds a blacklist for devices where powersaving is known to
cause problems and disables it on these devices.
Note I tried to put this blacklist in userspace first:
https://github.com/systemd/systemd/pull/8128
But the systemd maintainers rightfully pointed out that it would be
impossible to then later remove entries once we actually find a way to
make power-saving work on listed boards without issues. Having this list
in the kernel will allow removal of the blacklist entry in the same commit
which fixes the clicks / plops.
The blacklist only applies to the default power_save module-option value,
if a user explicitly sets the module-option then the blacklist is not
used.
[ added an ifdef CONFIG_PM for the build error -- tiwai]
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1525104
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=198611
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
After the conversion from platform to component the following warnings
are seen:
fsl-ssi-dai 2028000.ssi: ASoC: Failed to create component debugfs
directory
fsl-spdif-dai 2004000.spdif: ASoC: Failed to create component debugfs
directory
As explained by Mark Brown:
"It's a legit warning - we shouldn't really be creating two components
for the same device. However this is a bit of a corner case as it's the
dmaengine platform driver which is kind of a virtual device, it's not
really the device that we use with DMA that's being represented but
rather the link between that and the DMA controller."
Disambiguate the DMA component name by adding a "dma" debugfs_prefix
entry.
Suggested-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch changes lisence comment style from C to C++.
And use SPDX instead of boiler plate of GPLv2, as same as
other audio codec drivers.
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The recent support for the multiple PCM devices allowed user to use
multiple HDMI/DP outputs, but at the same time, the PCM stream
assignment has been changed, too. Due to that, the former PCM#0
(there was only one stream in the past) is likely assigned to a
different one (e.g. PCM#2), and it ends up with the regression when
user sticks with the fixed configuration using the device#0.
Although the multiple monitor support shouldn't matter when user
deploys the backend like PulseAudio that checks the jack detection
state, the behavior change isn't always acceptable for some users.
As a mitigation, this patch introduces an option to switch the
behavior back to the old-good-days: when the new option,
single_port=1, is passed, the driver creates only a single PCM device,
and it's assigned to the first connected one, like the earlier
versions did. The option is turned off as default still to support
the multiple monitors.
Fixes: 8a2d6ae1f7 ("ALSA: x86: Register multiple PCM devices for the LPE audio card")
Reported-and-tested-by: Hubert Mantel <mantel@metadox.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since ssi->streams is being updated along with SCR register and
its SSIEN bit, it's simpler to use it instead.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Caleb Crome <caleb@crome.org>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch cleans up probe() function by moving all Device Tree
related code into a separate function. It allows the probe() to
be Device Tree independent. This will be very useful for future
integration of imx-ssi driver which has similar functionalities
while exists only because it supports non-DT cases.
This patch also moves symmetric_channels of AC97 from the probe
to the structure snd_soc_dai_driver for simplification.
Additionally, since PowerPC and AC97 use the same pdev pointer
to register a platform device, this patch also unifies related
code.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Caleb Crome <caleb@crome.org>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
Using symmetric_rates in the cpu_dai_drv is a bit implicit,
so this patch adds a bool synchronous instead.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Caleb Crome <caleb@crome.org>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
The _fsl_ssi_set_dai_fmt() is a helper function being called from
fsl_ssi_set_dai_fmt() as an ASoC operation and fsl_ssi_hw_init()
mainly for AC97 format initialization.
This patch cleans the _fsl_ssi_set_dai_fmt() in following ways:
* Removing *dev pointer in the parameters as it's included in the
*ssi pointer of struct fsl_ssi.
* Using regmap_update_bits() instead of regmap_read() with masking
the value manually.
* Moving baudclk check to the switch-case routine to skip the I2S
master check. And moving SxCCR.DC settings after baudclk check.
* Adding format settings for SND_SOC_DAIFMT_AC97 like others.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Caleb Crome <caleb@crome.org>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
AC97 configures most of registers earlier to start a communication
with CODECs in order to successfully initialize CODEC. Currently,
_fsl_ssi_set_dai_fmt() and fsl_ssi_setup_ac97() are called to get
all SSI registers properly set.
Since now the driver has a fsl_ssi_hw_init() to handle all register
initial settings, this patch moves those register settings of AC97
to the fsl_ssi_hw_init() as well.
Meanwhile it applies _fsl_ssi_set_dai_fmt() call to AC97 only since
other formats would be configured via normal set_dai_fmt() directly.
This patch also adds fsl_ssi_hw_clean() to cleanup control bits for
AC97 in the platform remote() function.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Caleb Crome <caleb@crome.org>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
The probe() could handle some one-time configurations since
they will not be changed once being configured.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Caleb Crome <caleb@crome.org>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since there is a helper function, use it to help readability.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Caleb Crome <caleb@crome.org>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
It'd be safer to enable both FIFOs for TX or RX at the same time.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Caleb Crome <caleb@crome.org>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch cleans fsl_ssi_setup_regvals() by following changes:
1) Moving DBG bits to the first lines.
2) Setting SSIE, RE/TE as default and cleaning it for AC97
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Caleb Crome <caleb@crome.org>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
The _fsl_ssi_set_dai_fmt() bypasses an undefined format for AC97
mode. However, it's not really necessary if AC97 has its complete
format defined.
So this patch adds a DAIFMT macro of complete format including a
clock direction and polarity.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Caleb Crome <caleb@crome.org>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
The trigger() calls fsl_ssi_tx_config() and fsl_ssi_rx_config(),
and both of them jump to fsl_ssi_config(). And fsl_ssi_config()
later calls another fsl_ssi_rxtx_config().
However, the whole routine, especially fsl_ssi_config() function,
is too complicated because of the folowing reasons:
1) It has to handle the concern of the opposite stream.
2) It has to handle cases of offline configurations support.
3) It has to handle enable and disable operations while they're
mostly different.
Since the enable and disable routines have more differences than
TX and RX rountines, this patch simplifies these helper functions
with the following changes:
- Changing to two helper functions of enable and disable instead
of TX and RX.
- Removing fsl_ssi_rxtx_config() by separately integrating it to
two newly introduced enable & disable functions.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Caleb Crome <caleb@crome.org>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
The FIFO clear helper function is just one line of code now.
So it could be cleaned up by removing it and calling regmap
directly.
Meanwhile, FIFO clear could be applied to all use cases, not
confined to AC97. So this patch also moves FIFO clear in the
trigger() to fsl_ssi_config() and removes the AC97 check.
Note that SOR register is safe from offline_config HW limit.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Caleb Crome <caleb@crome.org>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
The define of fsl_ssi_disable_val is not so clear as it mixes two
steps of calculations together. And those parameter names are also
a bit long to read.
Since it just tries to exclude the shared bits from the regvals of
current stream while the opposite stream is active, it's better to
use something like ssi_excl_shared_bits.
This patch also bisects fsl_ssi_disable_val into two macros of two
corresponding steps and then shortens its parameter names. It also
updates callers in the fsl_ssi_config() accordingly.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Caleb Crome <caleb@crome.org>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
Checking TE and RE bits in SCR register doesn't work for AC97 mode
which enables SSIEN, TE and RE in the fsl_ssi_setup_ac97() that's
called during probe().
So when running into the trigger(), it will always get the result
of both TE and RE being enabled already, even if actually there is
no active stream.
This patch fixes this issue by adding a variable to log the active
streams manually.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Caleb Crome <caleb@crome.org>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch replaces the register read with ssi->i2s_net for
simplification. It also removes masking SSIEN from scr value
since it's handled later by regmap_update_bits() to set this
scr value back.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Caleb Crome <caleb@crome.org>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
The hw_params() overwrites i2s_net settings for special cases like
mono-channel support, however, it doesn't update ssi->i2s_net as
set_dai_fmt() does.
This patch removes the local i2s_net variable and directly updates
ssi->i2s_net in the hw_params() so that the driver can simply look
up the ssi->i2s_net instead of reading the register.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Caleb Crome <caleb@crome.org>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
The RX and TX macros were defined implicitly and there was
a potential risk if someone changes their values.
Since they were defined to index the array ssi->regvals[2],
this patch moves these two macros to fsl_ssi.c, closer to
its owner ssi->regvals. And it also puts some comments here
to limit their value within [0, 1].
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Caleb Crome <caleb@crome.org>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
Repair any formatting/style issues that can be fixed without major
code refactoring.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use // for .c and /* for .h files according to:
Documentation/process/license-rules.rst file.
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The hcp->chmap_info must not be freed up in the hdmi_codec_remove()
function as it leads to kernel crash due ALSA core's
pcm_chmap_ctl_private_free() is trying to free it up again when the card
destroyed via snd_card_free.
Since the driver was converted to devm_snd_soc_register_component() the
whole platform_device.remove can be removed.
Commit cd6111b262 ("ASoC: hdmi-codec: add channel mapping control")
should not have added the kfree(hcp->chmap_info); to the hdmi_codec_remove
function.
[Separate verison of the fix for -next -- broonie]
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The hcp->chmap_info must not be freed up in the hdmi_codec_remove()
function as it leads to kernel crash due ALSA core's
pcm_chmap_ctl_private_free() is trying to free it up again when the card
destroyed via snd_card_free.
Commit cd6111b262 ("ASoC: hdmi-codec: add channel mapping control")
should not have added the kfree(hcp->chmap_info); to the hdmi_codec_remove
function.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Jyri Sarha <jsarha@ti.com>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The max9759 is a gpio controlled amplifier.
Tested on a Variscite Dart MX6 SoM based custom board.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Modify SPDX comment style to match the rules. Since the original
code had a GPL-2.0 license and SPDX is compatible with GPL-2.0+,
we also modified the MODULE_LICENSE.
Signed-off-by: Cosmin-Gabriel Samoila <cosmin.samoila@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adding ACPI entry id for probing the driver.
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Removed hardcoding in dma descriptor programming api's.
These changes are required to extend the logic to support
dma descriptor programming for multiple i2s controller
instances.
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With in ACP, There are three I2S controllers can be configured.
(I2S SP ,I2S MICSP and I2S BT).These controllers can
support both playback/capture scenarios.
Default enabled i2s controller instance is i2s sp instance.
Renamed stream names and bytescount params as i2ssp.
These changes required to distinguish with other I2S controller
instance pcm substreams and bytescount params.
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now codec can be replaced to component, let's do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On some systems a delay is needed after switching on the clocks, to allow
the output to stabilize and avoid a popping noise at the beginning of
the recording. Add the optional device tree property 'wakeup-delay-ms'
and apply the specified delay after enabling the mic. A blocking delay
can't be applied in dmic_daiops_trigger() since the function is called
in atomic context. Instead use a DAPM event handler to set the enable
GPIO and apply the delay in the handler.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ALC5651 does not like multi-write accesses, avoid them. This fixes:
rt5651 i2c-10EC5651:00: Unable to sync registers 0x27-0x28. -121
Errors on resume (and all registers after the registers in the error not
being synced).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Enable 5-band graphic equalizer which allows manipulation of
gain in range -11.75dB to 12dB for 5 specific sound bands:
115Hz, 330Hz, 990Hz, 3000Hz, 9900Hz.
Signed-off-by: Michal Oleszczyk <oleszczyk.m@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add mux for choosing DAC source: ADC, I2S or DAP. DAP - digital
audio processing block. Moreover create choosing mux for DAP main
source (ADC or I2S) and DAP mixer source (ADC or I2S). Mixer block
allows summing DAP main and mixer sources togheter with defined
volumes.
Signed-off-by: Michal Oleszczyk <oleszczyk.m@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With P0 R29, Bit2 set the I2S clocks will be running when the DAC/ADC is
powered down, but still the codec need to be powered up by needing at least
one complete DAPM path for the stream.
If the AIF is not needed (analog loopback for example) the I2S clocks will
not run as they are not needed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Suggested-by: Stefan Müller-Klieser <s.mueller-klieser@phytec.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The audio interface is not really the DAC input. Use more generic name for
it.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now we can replace Codec to Component. Let's do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now we can replace Codec to Component. Let's do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When we have same register to tell capture and playback capability
of a device and we want separate cpu dais for playback and
capture. Then, DW_I2S_QUIRK_COMP_PARAM1 is used to enable one
capability per dai.
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
base and sysclk_reg should be unsigned int, as that is what
regmap takes as a register address.
sysclk_mask is used to mask unsigned register values so
should be unsigned.
sysclk_shift is a shift value so is not allowed to be negative.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 8419caa727 ("ASoC: sgtl5000: Do not disable regulators in
SND_SOC_BIAS_OFF") causes the sgtl5000 to fail after a suspend/resume
sequence:
Playing WAVE '/media/a2002011001-e02.wav' : Signed 16 bit Little
Endian, Rate 44100 Hz, Stereo
aplay: pcm_write:2051: write error: Input/output error
The problem is caused by the fact that the aforementioned commit
dropped the cache handling, so re-introduce the register map
resync to fix the problem.
Suggested-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
Fixes: 08660086ef ("ASoC: ak4458: Add support for AK4458 DAC driver")
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
AK5558 is a 32-bit, 768 kHZ sampling, differential input ADC
for digital audio systems.
Datasheet is available at:
https://www.akm.com/akm/en/file/datasheet/AK5558VN.pdf
Initial patch includes support for normal and TDM modes.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Junichi Wakasugi <wakasugi.jb@om.asahi-kasei.co.jp>
[initial coding for 3.18 kernel]
Signed-off-by: Mihai Serban <mihai.serban@nxp.com>
[cleanups and porting to 4.9 kernel]
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
[tdm support]
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
[pm support, cleanups and porting to latest kernel]
Signed-off-by: Mark Brown <broonie@kernel.org>
The AK4458 is a 32-bit 8ch Premium DAC that corresponds
to a 768kHz PCM input and an 11.2MHz DSD input at maximum.
It supports I2S, DSD and TDM modes with 24 or 32 bit MSB
or 16, 24, 32 LSB formats. Its datasheet is available here:
https://www.akm.com/akm/en/file/datasheet/AK4458VN.pdf
Signed-off-by: Junichi Wakasugi <wakasugi.jb@om.asahi-kasei.co.jp>
Signed-off-by: Mihai Serban <mihai.serban@nxp.com>
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Cosmin-Gabriel Samoila <cosmin.samoila@nxp.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds Kabylake-y I2S machine driver which uses
DA7219 as headset on ssp1 and MAX98357A codec as speaker
on ssp0.
Signed-off-by: Naveen Manohar <naveen.m@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
One of the recently introduced commits hadn't been build tested, fix
that.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is some duplicate code in soc-core.c, and the kernel provides
DEFINE_SHOW_ATTRIBUTE() helper macro to decrease it in seq_file.h.
Signed-off-by: Peng Donglin <dolinux.peng@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Don't populate the const array norm_addrs on the stack, instead make it
static. Makes the object code smaller by over 230 bytes. Also re-format
array data as the insertion of the static keywork made the first line
overly long.
Before:
text data bss dec hex filename
53780 34752 256 88788 15ad4 linux/sound/soc/codecs/tscs42xx.o
After:
text data bss dec hex filename
53461 34840 256 88557 159ed linux/sound/soc/codecs/tscs42xx.o
(gcc version 7.2.0 x86_64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The check of blk_id == AUD_CLK_IO is redundant as it also being performed
in the following switch statement with the same return of -ENOTSUPP. Fix
this by removing the redundant comparison.
Detected by CoverityScan, CID#1465227 ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In usecases like hot plug-unplug DP panel or modeset during a playback,
sometimes we observe no audio after codec resets. During no audio
condition, we have noticed that the power state of the pin or the
connector is D3. Optimizing the way we set the power mitigates the
issue. With this changes the verb is sent to set the power state and
waits until actual state reaches target state. Thus ensuring power
state is set.
Signed-off-by: Abhijeet Kumar <abhijeet.kumar@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
{ NULL } only clears the first member of the structure.
Even though the first member of the snd_soc_dapm_update struct is a
pointer,it is more robust to use the empty struct initializer that
clears all the struct members.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
{ 0 } only clears the first member of the structure.
The first member of the snd_soc_dapm_update struct is a pointer,
and writing 0 to a pointer results in a sparse warning.
Use the empty struct initializer that clears all the struct members
and fixes the sparse warning.
Cc: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
{ 0 } only clears the first member of the structure.
The first member of the snd_soc_dapm_update struct is a pointer,
and writing 0 to a pointer results in a sparse warning.
Use the empty struct initializer that clears all the struct members
and fixes the sparse warning.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current implementation mute codec in global way (DAC block).
That means when user routes sound not from I2S but from
AUX source (LINE_IN) it also will be muted by alsa core.
This should not happen.
Signed-off-by: Michal Oleszczyk <oleszczyk.m@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In the reset state of the codec we do not have complete playback or capture
routes.
The audio playback/capture will not work due to missing clock signals on
the I2S bus if PLL, MDAC/NDAC/DAC MADC/NADC/ADC is powered down.
To make sure that even if all output/input is disconnected the codec is
generating clocks, we need to have valid DAPM route in every case to power
up the must needed parts of the codec.
I have verified that switching DAC (during playback) or ADC (during
capture) will stop the I2S clocks, so the only solution is to connect the
'Off' routes as well to output/input.
The routes will be only added if the codec is clock master. In case the
role changes runtime, the applied routes are removed.
Tested on am43x-epos-evm with aic3111 codec in master mode.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch defines I2S1 - HDMI DAI link and implements related
hw_params callback. The AUD PLL frequency is configured through
the CLK_SCLK_I2S1 leaf clock, the exynos5433 clock tree
definitions are updated in a separate patch.
The device tree parsing part is changed is a way it supports older
DTBs with just a single CPU DAI specified, without the HDMI link.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The SAMSUNG_I2S_OPCLK is not currently used by any card driver thus we can
safely change semantics of 'dir' argument of the I2S set_sysclk() callback.
Now an enumeration is exported instead of directly using register bit field
values.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
It seems both PCLK_I2S1 and SCLK_I2S1 clocks need to be enabled before
I2S1 control registers can be accessed on exynos5433. If SCLK clock
is disabled an exception is triggered. To fix this parent clock of
the RCLK_SRC clock is assigned to pri_dai->op_clk so required gate
clock is handled by the runtime PM ops.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
In order to support multiple instances of the I2S IP block the platform
device name is prepended to each clock registered by the driver.
The clock-output-names property is now not used, this should not cause
any issues as, for example, CDCLK clock is referenced through DT 'clocks'
property, not by name.
This change allows to have both I2S0 and I2S1 enabled simultaneously
on exynos5433 and working properly when #clock-cells property is specified
in respective DT nodes.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current soc_probe_dai() is using deep nested condition.
Thus, it is difficult to read/understand.
This patch simplification it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The dma_mapping_error() returns true or false, but we want to return
-ENOMEM if there was an error.
Fixes: e98131222f ("ASoC: uniphier: add support for UniPhier AIO compress audio")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Tested-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
{ 0 } only clears the first member of the structure.
The first member of the snd_soc_dapm_update struct is a pointer,
and writing 0 to a pointer results in the following sparse warning:
sound/soc/codecs/tlv320aic3x.c:175:47: warning: Using plain integer as NULL pointer
Use the empty struct initializer that clears all the struct members
and fixes the sparse warning.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
{ 0 } only clears the first member of the structure.
The first member of the snd_soc_dapm_update struct is a pointer,
and writing 0 to a pointer results in the following sparse warning:
sound/soc/codecs/wm9712.c:229:47: warning: Using plain integer as NULL pointer
Use the empty struct initializer that clears all the struct members
and fixes the sparse warning.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_runtime_ignore_pmdown_time() returns "ignore pmdown time"
decision. Then, it collects each component driver's .use_pmdown_time
settings by using AND operation.
But, ak4613 has no reason to ignore/use pmdown time.
Thus, It should has use_pmdown_time=0, it means it doesn't have
decision right of "ignore pmdown time".
Otherwise, ak4642 paired driver's pmdown_time settings doesn't
have meaning. In other words, "ignore pmdown time" is determined
irrespective of the value of paired driver's settings
(= ignore will be 0 by ak4642).
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_runtime_ignore_pmdown_time() returns "ignore pmdown time"
decision. Then, it collects each component driver's .use_pmdown_time
settings by using AND operation.
But, ak4613 has no reason to ignore/use pmdown time.
Thus, It should has use_pmdown_time=0, it means it doesn't have
decision right of "ignore pmdown time".
Otherwise, ak4613 paired driver's pmdown_time settings doesn't
have meaning. In other words, "ignore pmdown time" is determined
irrespective of the value of paired driver's settings
(= ignore will be 0 by ak4613).
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
These laptops have a combined jack to attach headsets, the U727 on
the left, the U757 on the right, but a headsets microphone doesn't
work. Using hdajacksensetest I found that pin 0x19 changed the
present state when plugging the headset, in addition to 0x21, but
didn't have the correct configuration (shown as "Not connected").
So this sets the configuration to the same values as the headphone
pin 0x21 except for the device type microphone, which makes it
work correctly. With the patch the configured pins for U727 are
Pin 0x12 (Internal Mic, Mobile-In): present = No
Pin 0x14 (Internal Speaker): present = No
Pin 0x19 (Black Mic, Left side): present = No
Pin 0x1d (Internal Aux): present = No
Pin 0x21 (Black Headphone, Left side): present = No
Signed-off-by: Jan-Marek Glogowski <glogow@fbihome.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALSA sequencer core initializes the event pool on demand by invoking
snd_seq_pool_init() when the first write happens and the pool is
empty. Meanwhile user can reset the pool size manually via ioctl
concurrently, and this may lead to UAF or out-of-bound accesses since
the function tries to vmalloc / vfree the buffer.
A simple fix is to just wrap the snd_seq_pool_init() call with the
recently introduced client->ioctl_mutex; as the calls for
snd_seq_pool_init() from other side are always protected with this
mutex, we can avoid the race.
Reported-by: 范龙飞 <long7573@126.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Audigy 2 CA0102 chip (but most likely others from the emu10k1 family,
too) has a problem that from time to time it likes to do few DMA reads a
bit beyond its normal allocation and gets very confused if these reads get
blocked by a IOMMU.
For the first (reserved) page this happens multiple times at every
playback, for various synth pages it happens randomly, rarely for PCM
playback buffers and the page table memory itself.
All these reads seem to follow a similar pattern, observed read offsets
beyond the allocation end were 0x00, 0x40, 0x80 and 0xc0 (PCI cache line
multiples), so it looks like the device tries to accesses up to 256 extra
bytes.
As a workaround let's widen these DMA allocations by an extra page if we
detect that the device is behind a non-passthrough IOMMU (the DMA memory
should be relatively plenty on IOMMU systems).
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit a5003fc041 ("[ALSA] emu10k1 - simplify page allocation for synth")
switched from using the DMA allocator for synth DMA pages to manually
calling alloc_page().
However, this usage has an implicit assumption that the DMA address space
for the emu10k1-family chip is the same as the CPU physical address space
which is not true for a system with a IOMMU.
Since this made the synth part of the driver non-functional on such systems
let's effectively revert that commit (while keeping the
__synth_free_pages() simplification).
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When we get a IOMMU page fault for a emu10k1 device it is very hard to
discover which of chip many DMA allocations triggered it (since on a IOMMU
system the DMA address space is often very different from the CPU one).
Let's add optional debug printouts providing this information.
These debug printouts are only enabled on an explicit request via the
kernel dynamic debug mechanism.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We have been calling dma_set_mask() and then dma_set_coherent_mask() with
the same value, but there is a dma_set_mask_and_coherent() function that
does exactly that so let's use it instead.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The emu10k1-family chips need the first page (index 0) reserved in their
page tables for some reason (every emu10k1 driver I've checked does this
without much of an explanation).
Using the first page for normal samples results in a broken playback.
However, we already have a dummy page allocated - so called "silent page"
and, in fact, had always been setting it as the first page in the chip page
table because an initialization of every entry of the page table to point
to a silent page happens after and overwrites the reserved_page allocation.
So the only thing remaining to remove the reserved_page allocation is a
trivial change to the page allocation logic to ignore the first page entry
and start its allocations from the second entry (index 1).
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now platform can be replaced to component, let's do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 48c3387642 ("ASoC: wm9081: replace codec to component")
replaced codec to component, but it didn't keep WM9081_DAC_DIGITAL_2
value to reg. This patch fixup it.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes: 041e74b714 ("ASoC: rt5659: Add the support of Intel HDA Header")
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes: f37fe2f998 ("ASoC: uniphier: add support for UniPhier AIO common driver")
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd_dai_call() is using dev_dbg(), but its message is sometimes
blocks nessesary other messages. If RSND_DEBUG_NO_DAI_CALL was
defined it will be suppressed by this patch.
Reported-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SSI/SRC have under/over flow error handling, and its status is useful
for debuging. But sometimes it might be too much message,
and it might blocks necessity other information.
To avoid such situation, basically this patch indicates interrupt
status debug message if DEBUG was defined, but it will be suppressed
if RSND_DEBUG_NO_IRQ_STATUS was defined.
Reported-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since sync_power_state is moved to core it's better to use the helper
function to ensure the actual power state reaches target instead of
using the local helper functions already exsisting in hda code.
Signed-off-by: Abhijeet Kumar <abhijeet.kumar@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current sync_power_state is local to hda code, moving it
core so that other users apart from hda legacy can use it.
The helper function ensures the actual state reaches the target state.
Signed-off-by: Abhijeet Kumar <abhijeet.kumar@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds support for UniPhier AIO sound driver
which is included in UniPhier LD11/LD20 SoCs.
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support of UniPhier AIO compress audio.
For passing through compress audio to S/PDIF.
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds CPU DAI driver for UniPhier AIO audio sound system.
This module provides PCM devices for all input/output port of AIO
such as I2S, S/PDIF.
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds supports for UniPhier AIO DMA.
This module shared register area with all sound devices for
I2S, S/PDIF and so on. Since the AIO has mixed register map
for those I/Os, it is hard to split register areas for each
sound devices.
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds common functions for UniPhier AIO audio sound
system. This provides commonly used APIs for input/output control
registers for UniPhier AIO.
This module provides all sound devices for I2S, S/PDIF and so on.
Since the AIO has mixed register map for those I/Os, it is hard
to split register areas for each sound devices.
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use dai name provided by framework from dev_name() function.
Signed-off-by: olivier moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Deferred probes shouldn't cause error messages in the boot log, so
change the dev_err() to the more harmless dev_info().
Signed-off-by: Martin Hundebøll <mnhu@prevas.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove rt5668 support from rt5665 codec driver since rt5668 will
not go into mass production.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
All sn95031 stuff was removed in commit 987da3fe17 ("ASoC: sn95031: remove this code")
Since SND_SOC_SN95031 was gone, remove makefile about it.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Clean makefile rules about inexistant files.
Thoses files were removed in commit a076d41823 ("ASoC: samsung: Drop AC97 drivers")
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now platform can be replaced to component, let's do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now platform can be replaced to component, let's do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Garlic Tseng <garlic.tseng@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now platform can be replaced to component, let's do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now platform can be replaced to component, let's do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now platform can be replaced to component, let's do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now platform can be replaced to component, let's do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now platform can be replaced to component, let's do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now platform can be replaced to component, let's do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now platform can be replaced to component, let's do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now platform can be replaced to component, let's do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now platform can be replaced to component, let's do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now platform can be replaced to component, let's do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now platform can be replaced to component, let's do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now platform can be replaced to component, let's do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now platform can be replaced to component, let's do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now platform can be replaced to component, let's do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now platform can be replaced to component, let's do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now platform can be replaced to component, let's do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now platform can be replaced to component, let's do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now platform can be replaced to component, let's do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now platform can be replaced to component, let's do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now platform can be replaced to component, let's do it.
This patch merges wm5102_compr_platform into soc_codec_dev_wm5102
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Tested-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now platform can be replaced to component, let's do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Tested-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now platform can be replaced to component, let's do it.
This patch merges rt5514_spi_dai_component into rt5514_spi_component
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now platform can be replaced to component, let's do it.
This patch merges cs47l24_compr_platform into soc_codec_dev_cs47l24
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Tested-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now platform can be replaced to component, let's do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Mukunda,Vijendar <vijendar.mukunda@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now platform can be replaced to component, let's do it.
To avoid complex operation, this patch adds device pointer
to atmel_classd.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now platform can be replaced to component, let's do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now platform can be replaced to component, let's do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now platform can be replaced to component, let's do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now platform can be replaced to component, let's do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now platform can be replaced to component, let's do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now platform can be replaced to component, let's do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now platform can be replaced to component, let's do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now platform can be replaced to component, let's do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: "Kp, Jeeja" <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now platform can be replaced to component, let's do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: "Kp, Jeeja" <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now platform can be replaced to component, let's do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now platform can be replaced to component, let's do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now, we are ready to replace rtd->platform to rtdcom list.
From this patch, rtd->platform check is no longer needed.
It will be replaced into rtdcom.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now we can replace Codec to Component. Let's do it.
Because Intel/Mediatek platforms are using rt5645/rt5677,
we need to update these all related drivers in same time.
Otherwise compile error/warning happen
rt5645:
xxx_codec_xxx() -> xxx_component_xxx()
.idle_bias_off = 1 -> .idle_bias_on = 0
.ignore_pmdown_time = 0 -> .use_pmdown_time = 1
- -> .endianness = 1
- -> .non_legacy_dai_naming = 1
rt5677:
xxx_codec_xxx() -> xxx_component_xxx()
.idle_bias_off = 1 -> .idle_bias_on = 0
.ignore_pmdown_time = 0 -> .use_pmdown_time = 1
- -> .endianness = 1
- -> .non_legacy_dai_naming = 1
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Hans de Goede