On some systems, the BIOS expects certain SMBus register values to
match the hardware defaults. Restore these configuration registers at
shutdown time to avoid confusing the BIOS. This avoids hard-locking
such systems upon reboot.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jason Andryuk <jandryuk@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@vger.kernel.org
Saving the original value of register SMBSLVCMD in
i801_enable_host_notify() doesn't work, because this function is
called not only at probe time but also at resume time. Do it in
i801_probe() instead, so that the saved value is not overwritten at
resume time.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Fixes: 22e94bd677 ("i2c: i801: store and restore the SLVCMD register at load and unload")
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Jason Andryuk <jandryuk@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@vger.kernel.org # v4.10+
Pull i2c updates from Wolfram Sang:
-I2C core now reports proper OF style module alias. I'd like to repeat
the note from the commit msg here (Thanks, Javier!):
NOTE: This patch may break out-of-tree drivers that were relying
on this behavior, and only had an I2C device ID table even
when the device was registered via OF.
There are no remaining drivers in mainline that do this, but
out-of-tree drivers have to be fixed and define a proper OF
device ID table to have module auto-loading working.
- new driver for the SynQuacer I2C controller
- major refactoring of the QUP driver
- the piix4 driver now uses request_muxed_region which should fix a
long standing resource conflict with the sp5100_tco watchdog
- a bunch of small core & driver improvements
* 'i2c/for-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (53 commits)
i2c: add support for Socionext SynQuacer I2C controller
dt-bindings: i2c: add binding for Socionext SynQuacer I2C
i2c: Update i2c_trace_msg static key to modern api
i2c: fix parameter of trace_i2c_result
i2c: imx: avoid taking clk_prepare mutex in PM callbacks
i2c: imx: use clk notifier for rate changes
i2c: make i2c_check_addr_validity() static
i2c: rcar: fix mask value of prohibited bit
dt-bindings: i2c: document R8A77965 bindings
i2c: pca-platform: drop gpio from platform data
i2c: pca-platform: use device_property_read_u32
i2c: pca-platform: unconditionally use devm_gpiod_get_optional
sh: sh7785lcr: add GPIO lookup table for i2c controller reset
i2c: qup: reorganization of driver code to remove polling for qup v2
i2c: qup: reorganization of driver code to remove polling for qup v1
i2c: qup: send NACK for last read sub transfers
i2c: qup: fix buffer overflow for multiple msg of maximum xfer len
i2c: qup: change completion timeout according to transfer length
i2c: qup: use the complete transfer length to choose DMA mode
i2c: qup: proper error handling for i2c error in BAM mode
...
This is a cleaned up version of the I2C controller driver for
the Fujitsu F_I2C IP, which was never supported upstream, and
has now been incorporated into the Socionext SynQuacer SoC.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
[wsa: updated MAINTAINERS entry and removed two empty lines]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This is unsafe, as the runtime PM callbacks are called from the PM
workqueue, so this may deadlock when handling an i2c attached clock,
which may already hold the clk_prepare mutex from another context.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Instead of repeatedly calling clk_get_rate for each transfer, register
a clock notifier to update the cached divider value each time the clock
rate actually changes.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This removes the entire architecture code for blackfin, cris, frv, m32r,
metag, mn10300, score, and tile, including the associated device drivers.
I have been working with the (former) maintainers for each one to ensure
that my interpretation was right and the code is definitely unused in
mainline kernels. Many had fond memories of working on the respective
ports to start with and getting them included in upstream, but also saw
no point in keeping the port alive without any users.
In the end, it seems that while the eight architectures are extremely
different, they all suffered the same fate: There was one company
in charge of an SoC line, a CPU microarchitecture and a software
ecosystem, which was more costly than licensing newer off-the-shelf
CPU cores from a third party (typically ARM, MIPS, or RISC-V). It seems
that all the SoC product lines are still around, but have not used the
custom CPU architectures for several years at this point. In contrast,
CPU instruction sets that remain popular and have actively maintained
kernel ports tend to all be used across multiple licensees.
The removal came out of a discussion that is now documented at
https://lwn.net/Articles/748074/. Unlike the original plans, I'm not
marking any ports as deprecated but remove them all at once after I made
sure that they are all unused. Some architectures (notably tile, mn10300,
and blackfin) are still being shipped in products with old kernels,
but those products will never be updated to newer kernel releases.
After this series, we still have a few architectures without mainline
gcc support:
- unicore32 and hexagon both have very outdated gcc releases, but the
maintainers promised to work on providing something newer. At least
in case of hexagon, this will only be llvm, not gcc.
- openrisc, risc-v and nds32 are still in the process of finishing their
support or getting it added to mainline gcc in the first place.
They all have patched gcc-7.3 ports that work to some degree, but
complete upstream support won't happen before gcc-8.1. Csky posted
their first kernel patch set last week, their situation will be similar.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=fQ8z
-----END PGP SIGNATURE-----
Merge tag 'arch-removal' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pul removal of obsolete architecture ports from Arnd Bergmann:
"This removes the entire architecture code for blackfin, cris, frv,
m32r, metag, mn10300, score, and tile, including the associated device
drivers.
I have been working with the (former) maintainers for each one to
ensure that my interpretation was right and the code is definitely
unused in mainline kernels. Many had fond memories of working on the
respective ports to start with and getting them included in upstream,
but also saw no point in keeping the port alive without any users.
In the end, it seems that while the eight architectures are extremely
different, they all suffered the same fate: There was one company in
charge of an SoC line, a CPU microarchitecture and a software
ecosystem, which was more costly than licensing newer off-the-shelf
CPU cores from a third party (typically ARM, MIPS, or RISC-V). It
seems that all the SoC product lines are still around, but have not
used the custom CPU architectures for several years at this point. In
contrast, CPU instruction sets that remain popular and have actively
maintained kernel ports tend to all be used across multiple licensees.
[ See the new nds32 port merged in the previous commit for the next
generation of "one company in charge of an SoC line, a CPU
microarchitecture and a software ecosystem" - Linus ]
The removal came out of a discussion that is now documented at
https://lwn.net/Articles/748074/. Unlike the original plans, I'm not
marking any ports as deprecated but remove them all at once after I
made sure that they are all unused. Some architectures (notably tile,
mn10300, and blackfin) are still being shipped in products with old
kernels, but those products will never be updated to newer kernel
releases.
After this series, we still have a few architectures without mainline
gcc support:
- unicore32 and hexagon both have very outdated gcc releases, but the
maintainers promised to work on providing something newer. At least
in case of hexagon, this will only be llvm, not gcc.
- openrisc, risc-v and nds32 are still in the process of finishing
their support or getting it added to mainline gcc in the first
place. They all have patched gcc-7.3 ports that work to some
degree, but complete upstream support won't happen before gcc-8.1.
Csky posted their first kernel patch set last week, their situation
will be similar
[ Palmer Dabbelt points out that RISC-V support is in mainline gcc
since gcc-7, although gcc-7.3.0 is the recommended minimum - Linus ]"
This really says it all:
2498 files changed, 95 insertions(+), 467668 deletions(-)
* tag 'arch-removal' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic: (74 commits)
MAINTAINERS: UNICORE32: Change email account
staging: iio: remove iio-trig-bfin-timer driver
tty: hvc: remove tile driver
tty: remove bfin_jtag_comm and hvc_bfin_jtag drivers
serial: remove tile uart driver
serial: remove m32r_sio driver
serial: remove blackfin drivers
serial: remove cris/etrax uart drivers
usb: Remove Blackfin references in USB support
usb: isp1362: remove blackfin arch glue
usb: musb: remove blackfin port
usb: host: remove tilegx platform glue
pwm: remove pwm-bfin driver
i2c: remove bfin-twi driver
spi: remove blackfin related host drivers
watchdog: remove bfin_wdt driver
can: remove bfin_can driver
mmc: remove bfin_sdh driver
input: misc: remove blackfin rotary driver
input: keyboard: remove bf54x driver
...
The blackfin architecture is getting removed, so the
twi driver can also be removed.
Acked-by: Aaron Wu <aaron.wu@analog.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
According to documentation, Bit 7 of ICMSR is unused and 0 should be
written to it. Fix the mask accordingly.
Signed-off-by: Hiromitsu Yamasaki <hiromitsu.yamasaki.ym@renesas.com>
[wsa: edited commit message]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
-----BEGIN PGP SIGNATURE-----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=rCow
-----END PGP SIGNATURE-----
Merge tag 'at24-4.17-updates-for-wolfram' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into i2c/for-4.17
"three new special cases for device tree compatible strings"
Use device_property_read_u32 instead of of_property_read_u32_index to
lookup the "clock-frequency" property.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Allow for the reset-gpios property to be defined in the device tree
or via a GPIO lookup table.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Following are the major issues in current driver code
1. The current driver simply assumes the transfer completion
whenever its gets any non-error interrupts and then simply do the
polling of available/free bytes in FIFO.
2. The block mode is not working properly since no handling in
being done for OUT_BLOCK_WRITE_REQ and IN_BLOCK_READ_READ.
3. An i2c transfer can contain multiple message and QUP v2
supports reconfiguration during run in which the mode should be same
for all the sub transfer. Currently the mode is being programmed
before every sub transfer which is functionally wrong. If one message
is less than FIFO length and other message is greater than FIFO
length, then transfers will fail.
Because of above, i2c v2 transfers of size greater than 64 are failing
with following error message
i2c_qup 78b6000.i2c: timeout for fifo out full
To make block mode working properly and move to use the interrupts
instead of polling, major code reorganization is required. Following
are the major changes done in this patch
1. Remove the polling of TX FIFO free space and RX FIFO available
bytes and move to interrupts completely. QUP has QUP_MX_OUTPUT_DONE,
QUP_MX_INPUT_DONE, OUT_BLOCK_WRITE_REQ and IN_BLOCK_READ_REQ
interrupts to handle FIFO’s properly so check all these interrupts.
2. Determine the mode for transfer before starting by checking
all the tx/rx data length in each message. The complete message can be
transferred either in DMA mode or Programmed IO by FIFO/Block mode.
in DMA mode, both tx and rx uses same mode but in PIO mode, the TX and
RX can be in different mode.
3. During write, For FIFO mode, TX FIFO can be directly written
without checking for FIFO space. For block mode, the QUP will generate
OUT_BLOCK_WRITE_REQ interrupt whenever it has block size of available
space.
4. During read, both TX and RX FIFO will be used. TX will be used
for writing tags and RX will be used for receiving the data. In QUP,
TX and RX can operate in separate mode so configure modes accordingly.
5. For read FIFO mode, wait for QUP_MX_INPUT_DONE interrupt which
will be generated after all the bytes have been copied in RX FIFO. For
read Block mode, QUP will generate IN_BLOCK_READ_REQ interrupts
whenever it has block size of available data.
6. Split the transfer in chunk of one QUP block size(256 bytes)
and schedule each block separately. QUP v2 supports reconfiguration
during run in which QUP can transfer multiple blocks without issuing a
stop events.
7. Port the SMBus block read support for new code changes.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Following are the major issues in current driver code
1. The current driver simply assumes the transfer completion
whenever its gets any non-error interrupts and then simply do the
polling of available/free bytes in FIFO.
2. The block mode is not working properly since no handling in
being done for OUT_BLOCK_WRITE_REQ and IN_BLOCK_READ_REQ.
Because of above, i2c v1 transfers of size greater than 32 are failing
with following error message
i2c_qup 78b6000.i2c: timeout for fifo out full
To make block mode working properly and move to use the interrupts
instead of polling, major code reorganization is required. Following
are the major changes done in this patch
1. Remove the polling of TX FIFO free space and RX FIFO available
bytes and move to interrupts completely. QUP has QUP_MX_OUTPUT_DONE,
QUP_MX_INPUT_DONE, OUT_BLOCK_WRITE_REQ and IN_BLOCK_READ_REQ
interrupts to handle FIFO’s properly so check all these interrupts.
2. During write, For FIFO mode, TX FIFO can be directly written
without checking for FIFO space. For block mode, the QUP will generate
OUT_BLOCK_WRITE_REQ interrupt whenever it has block size of available
space.
3. During read, both TX and RX FIFO will be used. TX will be used
for writing tags and RX will be used for receiving the data. In QUP,
TX and RX can operate in separate mode so configure modes accordingly.
4. For read FIFO mode, wait for QUP_MX_INPUT_DONE interrupt which
will be generated after all the bytes have been copied in RX FIFO. For
read Block mode, QUP will generate IN_BLOCK_READ_REQ interrupts
whenever it has block size of available data.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
According to I2c specification, “If a master-receiver sends a
repeated START condition, it sends a not-acknowledge (A) just
before the repeated START condition”. QUP v2 supports sending
of NACK without stop with QUP_TAG_V2_DATARD_NACK so added the
same.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Austin Christ <austinwc@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The BAM mode requires buffer for start tag data and tx, rx SG
list. Currently, this is being taken for maximum transfer length
(65K). But an I2C transfer can have multiple messages and each
message can be of this maximum length so the buffer overflow will
happen in this case. Since increasing buffer length won’t be
feasible since an I2C transfer can contain any number of messages
so this patch does following changes to make i2c transfers working
for multiple messages case.
1. Calculate the required buffers for 2 maximum length messages
(65K * 2).
2. Split the descriptor formation and descriptor scheduling.
The idea is to fit as many messages in one DMA transfers for 65K
threshold value (max_xfer_sg_len). Whenever the sg_cnt is
crossing this, then schedule the BAM transfer and subsequent
transfer will again start from zero.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Currently the completion timeout is being taken according to
maximum transfer length which is too high if SCL is operating in
high frequency. This patch calculates timeout on the basis of
one-byte transfer time and uses the same for completion timeout.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Currently each message length in complete transfer is being
checked for determining DMA mode and if any of the message length
is less than FIFO length then non DMA mode is being used which
will increase overhead. DMA can be used for any length and it
should be determined with complete transfer length. Now, this
patch selects DMA mode if the total length is greater than FIFO
length.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Austin Christ <austinwc@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Currently the i2c error handling in BAM mode is not working
properly in stress condition.
1. After an error, the FIFO are being written with FLUSH and
EOT tags which should not be required since already these tags
have been written in BAM descriptor itself.
2. QUP state is being moved to RESET in IRQ handler in case
of error. When QUP HW encounters an error in BAM mode then it
moves the QUP STATE to PAUSE state. In this case, I2C_FLUSH
command needs to be executed while moving to RUN_STATE by writing
to the QUP_STATE register with the I2C_FLUSH bit set to 1.
3. In Error case, sometimes, QUP generates more than one
interrupt which will trigger the complete again. After an error,
the flush operation will be scheduled after doing
reinit_completion which should be triggered by BAM IRQ callback.
If the second QUP IRQ comes during this time then it will call
the complete and the transfer function will assume the all the
BAM HW descriptors have been completed.
4. The release DMA is being called after each error which
will free the DMA tx and rx channels. The error like NACK is very
common in I2C transfer and every time this will be overhead. Now,
since the error handling is proper so this release channel can be
completely avoided.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Sricharan R <sricharan@codeaurora.org>
Reviewed-by: Austin Christ <austinwc@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In case of FLUSH operation, BAM copies INPUT EOT FLUSH (0x94)
instead of normal EOT (0x93) tag in input data stream when an
input EOT tag is received during flush operation. So only one tag
will be written instead of 2 separate tags.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The role of FLUSH and EOT tag is to flush already scheduled
descriptors in BAM HW in case of error. EOT is required only
when descriptors are scheduled in RX FIFO. If all the messages
are WRITE, then only FLUSH tag will be used.
A single BAM transfer can have multiple read and write messages.
The EOT and FLUSH tags should be scheduled at the end of BAM HW
descriptors. Since the READ and WRITE can be present in any order
so for some of the cases, these tags are not being written
correctly.
Following is one of the example
READ, READ, READ, READ
Currently EOT and FLUSH tags are being written after each READ.
If QUP gets NACK for first READ itself, then flush will be
triggered. It will look for first FLUSH tag in TX FIFO and will
stop there so only descriptors for first READ descriptors be
flushed. All the scheduled descriptors should be cleared to
generate BAM DMA completion.
Now this patch is scheduling FLUSH and EOT only once after all the
descriptors. So, flush will clear all the scheduled descriptors and
BAM will generate the completion interrupt.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The rx_nents and tx_nents are redundant. rx_buf and tx_buf can
be used for total number of SG entries. Since rx_buf and tx_buf
give the impression that it is buffer instead of count so rename
it to tx_cnt and rx_cnt for giving it more meaningful variable
name.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Austin Christ <austinwc@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
1. Assigns use_dma in qup_dev structure itself which will
help in subsequent patches to determine the mode in IRQ handler.
2. Does minor code reorganization for loops to reduce the
unnecessary comparison and assignment.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Austin Christ <austinwc@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The QUP BSLP BAM generates the following error sometimes if the
current I2C DMA transfer fails and the flush operation has been
scheduled
“bam-dma-engine 7884000.dma: Cannot free busy channel”
If any I2C error comes during BAM DMA transfer, then the QUP I2C
interrupt will be generated and the flush operation will be
carried out to make I2C consume all scheduled DMA transfer.
Currently, the same completion structure is being used for BAM
transfer which has already completed without reinit. It will make
flush operation wait_for_completion_timeout completed immediately
and will proceed for freeing the DMA resources where the
descriptors are still in process.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Acked-by: Sricharan R <sricharan@codeaurora.org>
Reviewed-by: Austin Christ <austinwc@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The file has been updated from 2016 to 2018 so fixed the
copyright years.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In case we receive NACK on DATA we shouldn't be resetting the controller,
rather we should issue STOP command. This will terminate the current
transaction and -EIO is returned.
While at that handle the SMBus Quick Command properly.
We shouldn't be setting the XLP9XX_I2C_CMD_READ/WRITE for such
transactions.
Signed-off-by: George Cherian <george.cherian@cavium.com>
Reviewed-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I2C bus enters the STOP condition after the DATA_DONE interrupt is raised.
Essentially the driver should be checking the bus state before sending
any transaction. In case a transaction is initiated while the
bus is busy, the prior transaction's stop condition is not achieved.
Add the check to make sure the bus is not busy before every transaction.
Signed-off-by: George Cherian <george.cherian@cavium.com>
Reviewed-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The hardware may not support SDA hold time configuration, but if it is
not set in the Device Tree either, there is no need to print a warning.
Reported-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Alexander Monakov <amonakov@ispras.ru>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The errata FE-8471889 description has been updated. There is still a
timing violation for repeated start. But the errata now states that it
was only the case for the Standard mode (100 kHz), in Fast mode (400 kHz)
there is no issue.
This patch limit the errata fix to the Standard mode.
It has been tesed successfully on the clearfog (Aramda 388 based board).
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Suspend functions seem to have been copied from i2c-cadence driver.
Rename the functions to match the rest of the driver.
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
These patches remove the metag architecture and tightly dependent
drivers from the kernel. With the 4.16 kernel the ancient gcc 4.2.4
based metag toolchain we have been using is hitting compiler bugs, so
now seems a good time to drop it altogether.
-----BEGIN PGP SIGNATURE-----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=zDIl
-----END PGP SIGNATURE-----
Merge tag 'metag_remove_2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/jhogan/metag into asm-generic
Remove metag architecture
These patches remove the metag architecture and tightly dependent
drivers from the kernel. With the 4.16 kernel the ancient gcc 4.2.4
based metag toolchain we have been using is hitting compiler bugs, so
now seems a good time to drop it altogether.
* tag 'metag_remove_2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/jhogan/metag:
i2c: img-scb: Drop METAG dependency
media: img-ir: Drop METAG dependency
watchdog: imgpdc: Drop METAG dependency
MAINTAINERS/CREDITS: Drop METAG ARCHITECTURE
tty: Remove metag DA TTY and console driver
clocksource: Remove metag generic timer driver
irqchip: Remove metag irqchip drivers
Drop a bunch of metag references
docs: Remove remaining references to metag
docs: Remove metag docs
metag: Remove arch/metag/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Now that arch/metag/ has been removed, remove the METAG dependency from
the IMG SCB I2C device driver. The hardware is also present on MIPS SoCs
so the driver still has value.
Signed-off-by: James Hogan <jhogan@kernel.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Cc: linux-i2c@vger.kernel.org
Cc: linux-metag@vger.kernel.org
ACPI_ERROR and ACPI_DEBUG_PRINT are not intended to be used by device
drivers. Use acpi_handle message logging functions instead.
As a nice side effect, it removes the following compiler warnings
which were printed when ACPI debug is disabled:
drivers/i2c/busses/i2c-scmi.c: In function "acpi_smbus_cmi_add_cap":
drivers/i2c/busses/i2c-scmi.c:328:39: warning: suggest braces around empty body in an "else" statement [-Wempty-body]
drivers/i2c/busses/i2c-scmi.c:338:12: warning: suggest braces around empty body in an "else" statement [-Wempty-body]
Suggested-by: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Accesses to SB800_PIIX4_SMB_IDX can occur from multiple drivers.
One example for another driver is the sp5100_tco driver.
Use request_muxed_region() to ensure synchronization.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The piix4 i2c driver is extremely slow. Replacing msleep()
with usleep_range() increases its speed substantially.
Use sleep ranges similar to those used in the i2c-801 driver
to keep things simple.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The error message:
[Fri Feb 16 13:42:13 2018] i2c-thunderx 0000:01:09.4: unhandled state: 0
is mis-leading as state 0 (bus error) is not an unknown state.
Return -EIO as before but avoid printing the message. Also rename
STAT_ERROR to STATE_BUS_ERROR.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The pointer reg is assigned a value that is never read, it is later
overwritten with a new value, hence the redundant initialization can
be removed.
Cleans up clang warning:
drivers/i2c/busses/i2c-stm32f4.c:352:16: warning: Value stored to 'reg'
during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
HSI2C_MASTER_ST_LOSE state is not documented properly, extensive tests
show that hardware is usually able to recover from this state without
interrupting the transfer. Moreover documentation says that
such state can be caused by slave clock stretching, and should not be
treated as an error during transaction. The only place it indicates
an error is just before starting transaction. In such case bus recovery
procedure should be performed - master should pulse SCL line nine times
and then send STOP condition, it can be repeated until SDA goes high.
The procedure can be performed using manual commands HSI2C_CMD_READ_DATA
and HSI2C_CMD_SEND_STOP.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In case of transaction with I2C_M_RECV_LEN set, make sure the driver reads
the first byte and then updates the RX fifo with the expected length. Set
threshold to 1 byte so that driver gets an interrupt on receiving the first byte.
After which the transfer length is updated depending on the received length.
Also report SMBus block read functionality.
Signed-off-by: George Cherian <george.cherian@cavium.com>
Tested-by: dann frazier <dann.frazier@canonical.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fix the driver violation of the common practice to return
ENXIO error on a slave address NACK.
Signed-off-by: Dmitry Bazhenov <dmitry.bazhenov@auriga.com>
Signed-off-by: George Cherian <george.cherian@cavium.com>
Tested-by: dann frazier <dann.frazier@canonical.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
GPIO library can return -ENOSYS for the failed request.
Instead of failing ->probe() in this case override error code to 0.
Fixes: ca382f5b38 ("i2c: designware: add i2c gpio recovery option")
Reported-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We were leaving them in the power on state (or the state the firmware
had set up for some client, if we were taking over from them). The
boot state was 30 core clocks, when we actually want to sample some
time after (to make sure that the new input bit has actually arrived).
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Commits adding PCI IDs for Intel Braswell and Kaby Lake PCH-H lacked the
respective Kconfig and Documentation/i2c/busses/i2c-i801 change. Add
them now.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
One I2C bus on my Atom E3845 board has been broken since 4.9.
It has two devices, both declared by ACPI and with built-in drivers.
There are two back-to-back transactions originating from the kernel, one
targeting each device. The first transaction works, the second one locks
up the I2C controller. The controller never recovers.
These kernel logs show up whenever an I2C transaction is attempted after
this failure.
i2c-designware-pci 0000:00:18.3: timeout in disabling adapter
i2c-designware-pci 0000:00:18.3: timeout waiting for bus ready
Waiting for the I2C controller status to indicate that it is enabled
before programming it fixes the issue.
I have tested this patch on 4.14 and 4.15.
Fixes: commit 2702ea7dbe ("i2c: designware: wait for disable/enable only if necessary")
Cc: linux-stable <stable@vger.kernel.org> #4.13+
Signed-off-by: Ben Gardner <gardner.ben@gmail.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c updates from Wolfram Sang:
"I2C has the following changes for you:
- new flag to mark DMA safe buffers in i2c_msg. Also, some
infrastructure around it. And docs.
- huge refactoring of the at24 driver led by the new maintainer
Bartosz
- update I2C bus recovery to send STOP after recovery
- conversion from gpio to gpiod for I2C bus recovery
- adding a fault-injector to the i2c-gpio driver
- lots of small driver improvements, and bigger ones to
i2c-sh_mobile"
* 'i2c/for-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (99 commits)
i2c: mv64xxx: Add myself as maintainer for this driver
i2c: mv64xxx: Fix clock resource by adding an optional bus clock
i2c: mv64xxx: Remove useless test before clk_disable_unprepare
i2c: mxs: use true and false for boolean values
i2c: meson: update doc description to fix build warnings
i2c: meson: add configurable divider factors
dt-bindings: i2c: update documentation for the Meson-AXG
i2c: imx-lpi2c: add runtime pm support
i2c: rcar: fix some trivial typos in comments
i2c: davinci: fix the cpufreq transition
i2c: rk3x: add proper kerneldoc header
i2c: rk3x: account for const type of of_device_id.data
i2c: acorn: remove outdated path from file header
i2c: acorn: add MODULE_LICENSE tag
i2c: rcar: implement bus recovery
i2c: send STOP after successful bus recovery
i2c: ensure SDA is released in recovery if SDA is controllable
i2c: add 'set_sda' to bus_recovery_info
i2c: add identifier in declarations for i2c_bus_recovery
i2c: make kerneldoc about bus recovery more precise
...
These are mostly minor bugfixes, cleanup and many defconfig updates to
support added drivers. In particular OMAP and PXA keep cleaning up the
legacy code base, as usual.
Nvidia adds some more SoC support code for Tegra 186.
For the first time on years, we are actually adding a non-DT platform for,
the EP93xx based Liebherr controller BK3.1. It's a minor variation of
the EP93xx reference design and in active use, while EP93xx apparently
doesn't have enough new development to have any device tree support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJac0azAAoJEGCrR//JCVInuaAQAJBfJeqhFC01JeO+Oy/Sz3qh
WuZpT0ExfU1EFLnyBhEYJujDmlzNPcVacI53gSazpiksHboLpOodW+pX19NwOyzC
RSbyLa+W5MH1uXtIzV8dqwXboOWJ/Fh348VTSG4dw2JJ6i4k3U/9xboOVtnynCic
ww66FEEpFvJfNgch+7zcpHDwACqJ8nsrortNzEM8eV2jA/DOgv48EemTJqf1Lv1E
Z0nqIBEPvInPgCB3MX3KTD6CgbQ1qZOcWcEgR1tDRqmCuCgvp4xawiOBKos6QHaG
Iqgi3jI5rPJ391mhIQqK5duU5IKMY0FO6qxir7U+YNZm8vMmijPMwgEmlkG28mTT
6B7+ZNHXnSnFklpMetvCBDB8a+Lximft/oqecumowKJo0R9vZontnP4Jdbt9HLic
T99nzw2Xwhxo/J7kQXcGDoLyRAPgS1iiHyWXKbXADRlaftACeXL9iVTg+F9EAveq
WTDNmN6hbha4fN5PXUkcTAco96JtevT/H2ZDmYFBCSaqHy3QrNPJtDcVSIJd4CGT
uQJwXINHvR/nJrEl2ZLLsfMSJMBXWp79w7xb+QfkIa6UXL3hUwGC9Wd2jQZsdHf3
AQ/Q1oJ6epCvd2+4xo0EwiUMjr2MGqfLmtGBQkMzdSbFe50RhHe3w2Amy3VU03X+
vFB4zAmReWDZXgQ7+Dhg
=frm4
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"These are mostly minor bugfixes, cleanup and many defconfig updates to
support added drivers. In particular OMAP and PXA keep cleaning up the
legacy code base, as usual.
Nvidia adds some more SoC support code for Tegra 186.
For the first time on years, we are actually adding a non-DT platform
for the EP93xx based Liebherr controller BK3.1. It's a minor variation
of the EP93xx reference design and in active use, while EP93xx
apparently doesn't have enough new development to have any device tree
support"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (73 commits)
ARM: omap: hwmod: fix section mismatch warnings
ARM: pxa/tosa-bt: add MODULE_LICENSE tag
arm64: defconfig: enable CONFIG_ACPI_APEI_EINJ
arm64: defconfig: enable EDAC GHES option
arm64: defconfig: enable CONFIG_ACPI_APEI_MEMORY_FAILURE
ARM: imx_v6_v7_defconfig: enable CONFIG_CPU_FREQ_STAT
Wind down ARM/TANGO port
ARM: davinci: constify gpio_led
ARM: davinci: drop unneeded newline
soc: Add SoC driver for Gemini
ARM: SAMSUNG: Add SPDX license identifiers
ARM: S5PV210: Add SPDX license identifiers
ARM: S3C64XX: Add SPDX license identifiers
ARM: S3C24XX: Add SPDX license identifiers
ARM: EXYNOS: Add SPDX license identifiers
ARM: imx: remove unused imx3 pm definitions
ARM: imx: don't abort MMDC probe if power saving status doesn't match
ARM: imx_v6_v7_defconfig: enable RTC_DRV_MXC_V2
ARM: imx_v6_v7_defconfig: Add missing config for DART-MX6 SoM
ARM: davinci: Use PTR_ERR_OR_ZERO()
...
On Armada 7K/8K we need to explicitly enable the bus clock. The bus clock
is optional because not all the SoCs need them but at least for Armada
7K/8K it is actually mandatory.
The binding documentation is updating accordingly.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
clk_disable_unprepare() already checks that the clock pointer is valid.
No need to test it before calling it.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Jean Delvare