Add entry for the 10base-T1L full duplex mode.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently these two checks in ethnl_set_rings are added after rtnl_lock()
which will do useless works if the request is invalid.
So this patch moves these checks before the rtnl_lock() to avoid these
costs.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently tx push is a standard driver feature which controls use of a fast
path descriptor push. So this patch extends the ringparam APIs and data
structures to support set/get tx push by ethtool -G/g.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For applications running on a mix of platforms it's useful
to have a clear indication whether host's NIC supports the
geometry requirements of TCP zero-copy. TCP zero-copy Rx
requires data to be neatly placed into memory pages.
Most NICs can't do that.
This patch is adding GET support only, since the NICs
I work with either always have the feature enabled or
enable it whenever MTU is set to jumbo. In other words
I don't need SET. But adding set should be trivial.
(The only note on SET is that we will likely want
the setting to be "sticky" and use 0 / `unknown`
to reset it back to driver default.)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ethtool_get_phy_stats(), the phydev varaible is set to
dev->phydev but dev->phydev is still used. Replace
dev->phydev uses with phydev.
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported by Johannes, the tracker allocated in
ethnl_default_notify() is not really needed, as this
function is not expected to change a device reference count.
Fixes: e4b8954074 ("netlink: add net device refcount tracker to struct ethnl_req_info")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Tested-by: Johannes Berg <johannes@sipsolutions.net>
Link: https://lore.kernel.org/r/20220105170849.2610470-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2021-12-30
The following pull-request contains BPF updates for your *net-next* tree.
We've added 72 non-merge commits during the last 20 day(s) which contain
a total of 223 files changed, 3510 insertions(+), 1591 deletions(-).
The main changes are:
1) Automatic setrlimit in libbpf when bpf is memcg's in the kernel, from Andrii.
2) Beautify and de-verbose verifier logs, from Christy.
3) Composable verifier types, from Hao.
4) bpf_strncmp helper, from Hou.
5) bpf.h header dependency cleanup, from Jakub.
6) get_func_[arg|ret|arg_cnt] helpers, from Jiri.
7) Sleepable local storage, from KP.
8) Extend kfunc with PTR_TO_CTX, PTR_TO_MEM argument support, from Kumar.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The assignment here will be overwritten, so it should be deleted
The clang_analyzer complains as follows:
net/ethtool/netlink.c:
Value stored to 'ret' is never read
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: luo penghao <luo.penghao@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
sock.h is pretty heavily used (5k objects rebuilt on x86 after
it's touched). We can drop the include of filter.h from it and
add a forward declaration of struct sk_filter instead.
This decreases the number of rebuilt objects when bpf.h
is touched from ~5k to ~1k.
There's a lot of missing includes this was masking. Primarily
in networking tho, this time.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Acked-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://lore.kernel.org/bpf/20211229004913.513372-1-kuba@kernel.org
Commit 0976b888a1 ("ethtool: fix null-ptr-deref on ref tracker")
made the write to req_info.dev conditional, but as Eric points out
in a different follow up the structure is often allocated on the
stack and not kzalloc()'d so seems safer to always write the dev,
in case it's garbage on input.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems I missed that most ethnl_parse_header_dev_get() callers
declare an on-stack struct ethnl_req_info, and that they simply call
dev_put(req_info.dev) when about to return.
Add ethnl_parse_header_dev_put() helper to properly untrack
reference taken by ethnl_parse_header_dev_get().
Fixes: e4b8954074 ("netlink: add net device refcount tracker to struct ethnl_req_info")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev can be a NULL here, not all requests set require_dev.
Fixes: e4b8954074 ("netlink: add net device refcount tracker to struct ethnl_req_info")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a short period between a net device starts to be unregistered
and when it is actually gone. In that time frame ethtool operations
could still be performed, which might end up in unwanted or undefined
behaviours[1].
Do not allow ethtool operations after a net device starts its
unregistration. This patch targets the netlink part as the ioctl one
isn't affected: the reference to the net device is taken and the
operation is executed within an rtnl lock section and the net device
won't be found after unregister.
[1] For example adding Tx queues after unregister ends up in NULL
pointer exceptions and UaFs, such as:
BUG: KASAN: use-after-free in kobject_get+0x14/0x90
Read of size 1 at addr ffff88801961248c by task ethtool/755
CPU: 0 PID: 755 Comm: ethtool Not tainted 5.15.0-rc6+ #778
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-4.fc34 04/014
Call Trace:
dump_stack_lvl+0x57/0x72
print_address_description.constprop.0+0x1f/0x140
kasan_report.cold+0x7f/0x11b
kobject_get+0x14/0x90
kobject_add_internal+0x3d1/0x450
kobject_init_and_add+0xba/0xf0
netdev_queue_update_kobjects+0xcf/0x200
netif_set_real_num_tx_queues+0xb4/0x310
veth_set_channels+0x1c3/0x550
ethnl_set_channels+0x524/0x610
Fixes: 041b1c5d4a ("ethtool: helper functions for netlink interface")
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Link: https://lore.kernel.org/r/20211203101318.435618-1-atenart@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This helper might hold a netdev reference for a long time,
lets add reference tracking.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The 'dest' bitmap is fully initialized by the 'for' loop, so there is no
need to explicitly reset it.
This also makes this function in line with 'ethnl_features_to_bitmap32()'
which does not clear the destination before writing it.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/17fca158231c6f03689bd891254f0dd1f4e84cb8.1638091829.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The netdev (e.g. ifb, bareudp), which not support ethtool ops
(e.g. .get_drvinfo), we can use the rtnl kind as a default name.
ifb netdev may be created by others prefix, not ifbX.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Hao Chen <chenhao288@hisilicon.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: "Gustavo A. R. Silva" <gustavoars@kernel.org>
Cc: Danielle Ratson <danieller@nvidia.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20211125163049.84970-1-xiangxia.m.yue@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ethtool_set_coalesce() now uses both the .get_coalesce() and
.set_coalesce() callbacks. But the check for their availability is
buggy, so changing the coalesce settings on a device where the driver
provides only _one_ of the callbacks results in a NULL pointer
dereference instead of an -EOPNOTSUPP.
Fix the condition so that the availability of both callbacks is
ensured. This also matches the netlink code.
Note that reproducing this requires some effort - it only affects the
legacy ioctl path, and needs a specific combination of driver options:
- have .get_coalesce() and .coalesce_supported but no
.set_coalesce(), or
- have .set_coalesce() but no .get_coalesce(). Here eg. ethtool doesn't
cause the crash as it first attempts to call ethtool_get_coalesce()
and bails out on error.
Fixes: f3ccfda193 ("ethtool: extend coalesce setting uAPI with CQE mode")
Cc: Yufeng Mo <moyufeng@huawei.com>
Cc: Huazhong Tan <tanhuazhong@huawei.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Link: https://lore.kernel.org/r/20211126175543.28000-1-jwi@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add two new parameters kernel_ringparam and extack for
.get_ringparam and .set_ringparam to extend more ring params
through netlink.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to set rx buf len via ethtool -G parameter and get
rx buf len via ethtool -g parameter.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for ethtool to set/get tx copybreak buf size.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memset(), avoid intentionally writing across
neighboring fields.
Add struct_group() to mark region of struct stats_reply_data that should
be initialized, which can now be done in a single memset() call.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
ETHTOOL_A_PAUSE_STAT_MAX is the MAX attribute id,
so we need to subtract non-stats and add one to
get a count (IOW -2+1 == -1).
Otherwise we'll see:
ethnl cmd 21: calculated reply length 40, but consumed 52
Fixes: 9a27a33027 ("ethtool: add standard pause stats")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
devlink compat code needs to drop rtnl_lock to take
devlink->lock to ensure correct lock ordering.
This is problematic because we're not strictly guaranteed
that the netdev will not disappear after we re-lock.
It may open a possibility of nested ->begin / ->complete
calls.
Instead of calling into devlink under rtnl_lock take
a ref on the devlink instance and make the call after
we've dropped rtnl_lock.
We (continue to) assume that netdevs have an implicit
reference on the devlink returned from ndo_get_devlink_port
Note that ndo_get_devlink_port will now get called
under rtnl_lock. That should be fine since none of
the drivers seem to be taking serious locks inside
ndo_get_devlink_port.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to increase the lifetime of the data for .get_info
and .flash_update beyond their handlers inside rtnl_lock.
Allocate a union on the heap and use it instead.
Note that we now copy the ethcmd before we lookup dev,
hopefully there is no crazy user space depending on error
codes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't take the lock in net/core/dev_ioctl.c,
we'll have things to do outside rtnl_lock soon.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a pair of new ethtool messages, 'ETHTOOL_MSG_MODULE_SET' and
'ETHTOOL_MSG_MODULE_GET', that can be used to control transceiver
modules parameters and retrieve their status.
The first parameter to control is the power mode of the module. It is
only relevant for paged memory modules, as flat memory modules always
operate in low power mode.
When a paged memory module is in low power mode, its power consumption
is reduced to the minimum, the management interface towards the host is
available and the data path is deactivated.
User space can choose to put modules that are not currently in use in
low power mode and transition them to high power mode before putting the
associated ports administratively up. This is useful for user space that
favors reduced power consumption and lower temperatures over reduced
link up times. In QSFP-DD modules the transition from low power mode to
high power mode can take a few seconds and this transition is only
expected to get longer with future / more complex modules.
User space can control the power mode of the module via the power mode
policy attribute ('ETHTOOL_A_MODULE_POWER_MODE_POLICY'). Possible
values:
* high: Module is always in high power mode.
* auto: Module is transitioned by the host to high power mode when the
first port using it is put administratively up and to low power mode
when the last port using it is put administratively down.
The operational power mode of the module is available to user space via
the 'ETHTOOL_A_MODULE_POWER_MODE' attribute. The attribute is not
reported to user space when a module is not plugged-in.
The user API is designed to be generic enough so that it could be used
for modules with different memory maps (e.g., SFF-8636, CMIS).
The only implementation of the device driver API in this series is for a
MAC driver (mlxsw) where the module is controlled by the device's
firmware, but it is designed to be generic enough so that it could also
be used by implementations where the module is controlled by the CPU.
CMIS testing
============
# ethtool -m swp11
Identifier : 0x18 (QSFP-DD Double Density 8X Pluggable Transceiver (INF-8628))
...
Module State : 0x03 (ModuleReady)
LowPwrAllowRequestHW : Off
LowPwrRequestSW : Off
The module is not in low power mode, as it is not forced by hardware
(LowPwrAllowRequestHW is off) or by software (LowPwrRequestSW is off).
The power mode can be queried from the kernel. In case
LowPwrAllowRequestHW was on, the kernel would need to take into account
the state of the LowPwrRequestHW signal, which is not visible to user
space.
$ ethtool --show-module swp11
Module parameters for swp11:
power-mode-policy high
power-mode high
Change the power mode policy to 'auto':
# ethtool --set-module swp11 power-mode-policy auto
Query the power mode again:
$ ethtool --show-module swp11
Module parameters for swp11:
power-mode-policy auto
power-mode low
Verify with the data read from the EEPROM:
# ethtool -m swp11
Identifier : 0x18 (QSFP-DD Double Density 8X Pluggable Transceiver (INF-8628))
...
Module State : 0x01 (ModuleLowPwr)
LowPwrAllowRequestHW : Off
LowPwrRequestSW : On
Put the associated port administratively up which will instruct the host
to transition the module to high power mode:
# ip link set dev swp11 up
Query the power mode again:
$ ethtool --show-module swp11
Module parameters for swp11:
power-mode-policy auto
power-mode high
Verify with the data read from the EEPROM:
# ethtool -m swp11
Identifier : 0x18 (QSFP-DD Double Density 8X Pluggable Transceiver (INF-8628))
...
Module State : 0x03 (ModuleReady)
LowPwrAllowRequestHW : Off
LowPwrRequestSW : Off
Put the associated port administratively down which will instruct the
host to transition the module to low power mode:
# ip link set dev swp11 down
Query the power mode again:
$ ethtool --show-module swp11
Module parameters for swp11:
power-mode-policy auto
power-mode low
Verify with the data read from the EEPROM:
# ethtool -m swp11
Identifier : 0x18 (QSFP-DD Double Density 8X Pluggable Transceiver (INF-8628))
...
Module State : 0x01 (ModuleLowPwr)
LowPwrAllowRequestHW : Off
LowPwrRequestSW : On
SFF-8636 testing
================
# ethtool -m swp13
Identifier : 0x11 (QSFP28)
...
Extended identifier description : 5.0W max. Power consumption, High Power Class (> 3.5 W) enabled
Power set : Off
Power override : On
...
Transmit avg optical power (Channel 1) : 0.7733 mW / -1.12 dBm
Transmit avg optical power (Channel 2) : 0.7649 mW / -1.16 dBm
Transmit avg optical power (Channel 3) : 0.7790 mW / -1.08 dBm
Transmit avg optical power (Channel 4) : 0.7837 mW / -1.06 dBm
Rcvr signal avg optical power(Channel 1) : 0.9302 mW / -0.31 dBm
Rcvr signal avg optical power(Channel 2) : 0.9079 mW / -0.42 dBm
Rcvr signal avg optical power(Channel 3) : 0.8993 mW / -0.46 dBm
Rcvr signal avg optical power(Channel 4) : 0.8778 mW / -0.57 dBm
The module is not in low power mode, as it is not forced by hardware
(Power override is on) or by software (Power set is off).
The power mode can be queried from the kernel. In case Power override
was off, the kernel would need to take into account the state of the
LPMode signal, which is not visible to user space.
$ ethtool --show-module swp13
Module parameters for swp13:
power-mode-policy high
power-mode high
Change the power mode policy to 'auto':
# ethtool --set-module swp13 power-mode-policy auto
Query the power mode again:
$ ethtool --show-module swp13
Module parameters for swp13:
power-mode-policy auto
power-mode low
Verify with the data read from the EEPROM:
# ethtool -m swp13
Identifier : 0x11 (QSFP28)
Extended identifier description : 5.0W max. Power consumption, High Power Class (> 3.5 W) not enabled
Power set : On
Power override : On
...
Transmit avg optical power (Channel 1) : 0.0000 mW / -inf dBm
Transmit avg optical power (Channel 2) : 0.0000 mW / -inf dBm
Transmit avg optical power (Channel 3) : 0.0000 mW / -inf dBm
Transmit avg optical power (Channel 4) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 1) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 2) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 3) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 4) : 0.0000 mW / -inf dBm
Put the associated port administratively up which will instruct the host
to transition the module to high power mode:
# ip link set dev swp13 up
Query the power mode again:
$ ethtool --show-module swp13
Module parameters for swp13:
power-mode-policy auto
power-mode high
Verify with the data read from the EEPROM:
# ethtool -m swp13
Identifier : 0x11 (QSFP28)
...
Extended identifier description : 5.0W max. Power consumption, High Power Class (> 3.5 W) enabled
Power set : Off
Power override : On
...
Transmit avg optical power (Channel 1) : 0.7934 mW / -1.01 dBm
Transmit avg optical power (Channel 2) : 0.7859 mW / -1.05 dBm
Transmit avg optical power (Channel 3) : 0.7885 mW / -1.03 dBm
Transmit avg optical power (Channel 4) : 0.7985 mW / -0.98 dBm
Rcvr signal avg optical power(Channel 1) : 0.9325 mW / -0.30 dBm
Rcvr signal avg optical power(Channel 2) : 0.9034 mW / -0.44 dBm
Rcvr signal avg optical power(Channel 3) : 0.9086 mW / -0.42 dBm
Rcvr signal avg optical power(Channel 4) : 0.8885 mW / -0.51 dBm
Put the associated port administratively down which will instruct the
host to transition the module to low power mode:
# ip link set dev swp13 down
Query the power mode again:
$ ethtool --show-module swp13
Module parameters for swp13:
power-mode-policy auto
power-mode low
Verify with the data read from the EEPROM:
# ethtool -m swp13
Identifier : 0x11 (QSFP28)
...
Extended identifier description : 5.0W max. Power consumption, High Power Class (> 3.5 W) not enabled
Power set : On
Power override : On
...
Transmit avg optical power (Channel 1) : 0.0000 mW / -inf dBm
Transmit avg optical power (Channel 2) : 0.0000 mW / -inf dBm
Transmit avg optical power (Channel 3) : 0.0000 mW / -inf dBm
Transmit avg optical power (Channel 4) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 1) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 2) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 3) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 4) : 0.0000 mW / -inf dBm
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use array_size() helper instead of the open-coded version in
copy_{from,to}_user(). These sorts of multiplication factors
need to be wrapped in array_size().
Link: https://github.com/KSPP/linux/issues/160
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It shouldn't happen, but can happen that readable eeprom size is smaller
than announced. Then we would be stuck in an endless loop here because
after reaching the actual end reads return eeprom.len = 0. I faced this
issue when making a mistake in driver development. Detect this scenario
and return an error.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support more coalesce parameters through netlink,
add two new parameter kernel_coal and extack for .set_coalesce
and .get_coalesce, then some extra info can return to user with
the netlink API.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, there are many drivers who support CQE mode configuration,
some configure it as a fixed when initialized, some provide an
interface to change it by ethtool private flags. In order to make it
more generic, add two new 'ETHTOOL_A_COALESCE_USE_CQE_TX' and
'ETHTOOL_A_COALESCE_USE_CQE_RX' coalesce attributes, then these
parameters can be accessed by ethtool netlink coalesce uAPI.
Also add an new structure kernel_ethtool_coalesce, then the
new parameter can be added into this struct.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Julian reported that after d43c65b05b Coverity complains about a
missing check whether dev is NULL in ethnl_ops_complete().
There doesn't seem to be any valid case where dev could be NULL when
calling ethnl_ops_begin(), therefore return an error if dev is NULL.
Fixes: d43c65b05b ("ethtool: runtime-resume netdev parent in ethnl_ops_begin")
Reported-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'if (dev)' statement already move into dev_{put , hold}, so remove
redundant if statements.
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a network device is runtime-suspended then:
- network device may be flagged as detached and all ethtool ops (even if not
accessing the device) will fail because netif_device_present() returns
false
- ethtool ops may fail because device is not accessible (e.g. because being
in D3 in case of a PCI device)
It may not be desirable that userspace can't use even simple ethtool ops
that not access the device if interface or link is down. To be more friendly
to userspace let's ensure that device is runtime-resumed when executing the
respective ethtool op in kernel.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If device is runtime-suspended and not accessible then it may be
flagged as not present. If checking whether device is present is
done too early then we may bail out before we have the chance to
runtime-resume the device. Therefore move this check to
ethnl_ops_begin(). This is in preparation of a follow-up patch
that tries to runtime-resume the device before executing ethtool
ops.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation of subsequent extensions to both functions move the
implementations from netlink.h to netlink.c.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a network device is runtime-suspended then:
- network device may be flagged as detached and all ethtool ops (even if not
accessing the device) will fail because netif_device_present() returns
false
- ethtool ops may fail because device is not accessible (e.g. because being
in D3 in case of a PCI device)
It may not be desirable that userspace can't use even simple ethtool ops
that not access the device if interface or link is down. To be more friendly
to userspace let's ensure that device is runtime-resumed when executing the
respective ethtool op in kernel.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The compat handlers for SIOCDEVPRIVATE are incorrect for any driver that
passes data as part of struct ifreq rather than as an ifr_data pointer, or
that passes data back this way, since the compat_ifr_data_ioctl() helper
overwrites the ifr_data pointer and does not copy anything back out.
Since all drivers using devprivate commands are now converted to the
new .ndo_siocdevprivate callback, fix this by adding the missing piece
and passing the pointer separately the whole way.
This further unifies the native and compat logic for socket ioctls,
as the new code now passes the correct pointer as well as the correct
data for both native and compat ioctls.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool compat ioctl handling is hidden away in net/socket.c,
which introduces a couple of minor oddities:
- The implementation may end up diverging, as seen in the RXNFC
extension in commit 84a1d9c482 ("net: ethtool: extend RXNFC
API to support RSS spreading of filter matches") that does not work
in compat mode.
- Most architectures do not need the compat handling at all
because u64 and compat_u64 have the same alignment.
- On x86, the conversion is done for both x32 and i386 user space,
but it's actually wrong to do it for x32 and cannot work there.
- On 32-bit Arm, it never worked for compat oabi user space, since
that needs to do the same conversion but does not.
- It would be nice to get rid of both compat_alloc_user_space()
and copy_in_user() throughout the kernel.
None of these actually seems to be a serious problem that real
users are likely to encounter, but fixing all of them actually
leads to code that is both shorter and more readable.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since PTP virtual clock support is added, there can be
several PTP virtual clocks based on one PTP physical
clock for timestamping.
This patch is to extend SO_TIMESTAMPING API to support
PHC (PTP Hardware Clock) binding by adding a new flag
SOF_TIMESTAMPING_BIND_PHC. When PTP virtual clocks are
in use, user space can configure to bind one for
timestamping, but PTP physical clock is not supported
and not needed to bind.
This patch is preparation for timestamp conversion from
raw timestamp to a specific PTP virtual clock time in
core net.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an interface for getting PHC (PTP Hardware Clock)
virtual clocks, which are based on PHC physical clock
providing hardware timestamp to network packets.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Validate the offset to read from module EEPROM as part of the netlink
policy and remove the corresponding check from the code.
This also makes it possible to query the offset range from user space:
$ genl ctrl policy name ethtool
...
ID: 0x14 policy[32]:attr[2]: type=U32 range:[0,255]
...
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Validate the number of bytes to read from the module EEPROM as part of
the netlink policy and remove the corresponding check from the code.
This also makes it possible to query the length range from user space:
$ genl ctrl policy name ethtool
...
ID: 0x14 policy[32]:attr[3]: type=U32 range:[1,128]
...
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'ETHTOOL_A_MODULE_EEPROM_DATA' attribute is not part of the get
request.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial conflicts in net/can/isotp.c and
tools/testing/selftests/net/mptcp/mptcp_connect.sh
scaled_ppm_to_ppb() was moved from drivers/ptp/ptp_clock.c
to include/linux/ptp_clock_kernel.h in -next so re-apply
the fix there.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alexandru Tachici