Stop enabling the oscillator and removing the oscillator failure flags in
probe. Instead, return -EINVAL in .read_time when the oscillaotr is not
start or when it failed at some point. The oscillator gets enabled on the
first .set_time after failure and the failure flags are cleared.
This also removes the possibility of an infinite loop at probe where a
failing RTC will make the goto read_rtc to be taken every time.
Tested on mcp79411.
Reported-by: Mastro Gippo <gipmad@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
To be consistent change the S35390A_FLAG defines to use the BIT
macro (like the S35390A_INT2_MODE defines).
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
To simplify access and shorten code introduce a struct device pointer in
the s35390a probe function.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Alarms are only supported on a per minute basis. This is why
uie_unsupported is set. Furthermore issue a warning when a second based
alarm is requested.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Fix the INT2 mode mask to not include the "TEST" flag. Furthermore
remove the not needed reversion of bits when parsing the INT2 modes.
Instead reverse the INT2_MODE defines to match the bit order from the
datasheet.
Additionally mention the flag names from the datasheet for the different
modes in the comments.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Alarmtimer interface uses only the RTC with wekeup flags enabled.
Allow to use rtc-test driver with alarmtimer interface.
Signed-off-by: Roman Stratiienko <roman.stratiienko@globallogic.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Converting from hardware to host endiannes was done using reassignment
to the same variable which makes sparse unhappy as it can not verify
the endiannes handling properly. To allow sparse to verify endiannes
handling an explicit __le32 is introduced. Note that this patch does
not change the generated binary (x86_64 and ppc64 binary diff).
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Based on 1 normalized pattern(s):
licensed under gplv2 or later
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 118 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154040.961286471@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
51 franklin street fifth floor boston ma 02110 1301 usa
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option [no]_[pad]_[ctrl] any later version this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 51 franklin street fifth floor boston ma
02110 1301 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 176 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154040.652910950@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have MODULE_LICENCE("GPL*") inside which was used in the initial
scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have EXPORT_.*_SYMBOL_GPL inside which was used in the
initial scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Various driver updates for platforms and a couple of the small driver
subsystems we merge through our tree:
Among the larger pieces:
- Power management improvements for TI am335x and am437x (RTC suspend/wake)
- Misc new additions for Amlogic (socinfo updates)
- ZynqMP FPGA manager
- Nvidia improvements for reset/powergate handling
- PMIC wrapper for Mediatek MT8516
- Misc fixes/improvements for ARM SCMI, TEE, NXP i.MX SCU drivers
-----BEGIN PGP SIGNATURE-----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=YSfu
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms and a couple of the small driver
subsystems we merge through our tree:
Among the larger pieces:
- Power management improvements for TI am335x and am437x (RTC
suspend/wake)
- Misc new additions for Amlogic (socinfo updates)
- ZynqMP FPGA manager
- Nvidia improvements for reset/powergate handling
- PMIC wrapper for Mediatek MT8516
- Misc fixes/improvements for ARM SCMI, TEE, NXP i.MX SCU drivers"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (57 commits)
soc: aspeed: fix Kconfig
soc: add aspeed folder and misc drivers
spi: zynqmp: Fix build break
soc: imx: Add generic i.MX8 SoC driver
MAINTAINERS: Update email for Qualcomm SoC maintainer
memory: tegra: Fix a typos for "fdcdwr2" mc client
Revert "ARM: tegra: Restore memory arbitration on resume from LP1 on Tegra30+"
memory: tegra: Replace readl-writel with mc_readl-mc_writel
memory: tegra: Fix integer overflow on tick value calculation
memory: tegra: Fix missed registers values latching
ARM: tegra: cpuidle: Handle tick broadcasting within cpuidle core on Tegra20/30
optee: allow to work without static shared memory
soc/tegra: pmc: Move powergate initialisation to probe
soc/tegra: pmc: Remove reset sysfs entries on error
soc/tegra: pmc: Fix reset sources and levels
soc: amlogic: meson-gx-pwrc-vpu: Add support for G12A
soc: amlogic: meson-gx-pwrc-vpu: Fix power on/off register bitmask
fpga manager: Adding FPGA Manager support for Xilinx zynqmp
dt-bindings: fpga: Add bindings for ZynqMP fpga driver
firmware: xilinx: Add fpga API's
...
CrOS EC:
- Add EC host command support using rpmsg
- Add new CrOS USB PD logging driver
- Transfer spi messages at high priority
- Add support to trace CrOS EC commands
- Minor fixes and cleanups in protocol and debugfs
Wilco EC:
- Standardize Wilco EC mailbox interface
- Add h1_gpio status to debugfs
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEE6gYDF28Li+nEiKLaHwn1ewov5lgFAlzV61YACgkQHwn1ewov
5lgEFw//S7GVmBrFxcqu5wAjF1CW+mOGi3y6nVuTAHanWG/hJGWT+itOwsdDp6c9
TggYgohprz64JAZOPqPCTonV/qbxgsfKrSQRxFDtHH4F1iEUF46fnlsULDKi8VwM
Qzj4g4d//ePsOwHOsYVrbJRU2qKyF6Rm2hpOxKfI9u2Dv5fxLFu6fxUhrSq1Inr6
U67j7pxBwOnBtN2A6hMKHZaOUVkSNYT6azSPO3Z2YH0aky2Baxw/LPoRnbCNhwUQ
iyneX5+K0wpCz2fpnBF/QSh1QBACeyfrO6HHA+flfaejhShaWttrS36Gar+sdHFN
p6eeR1CoEJZbRY79Eetj8Cv5Be1ivVG/SC5JF4O1apAAn87wXLI6AaLG/03ul0vc
KOkcjrXMxISRlAUr+OKD0rg3Uo2oI0ht70XMT9DDsCRNDoVHvkDQJNdkWrKq+E1c
xL4YeLofZpcEN+Oe/WnwUZtYUdY3qcWs+C4hV+h0L0Ke5xir25DEUfF3j3J/uK2B
JEgkTpH8j6YjbGAErBPkTxWt5HE3oWtkK4moPlrfPKfxoSo2eRDvqz68qHsgIn8p
WBM+FSr+dQ7qyYDigMKrFSesiBpwCBI4lIgPxkvTxqbubaoZcsABHm3BUGjykXII
E5z2qsgRnDrB+uGGDkTvDoR0Kr3U0hGlag7u/N61H86PoiMLUig=
=NF5N
-----END PGP SIGNATURE-----
Merge tag 'tag-chrome-platform-for-v5.2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux
Pull chrome platform updates from Benson Leung:
"CrOS EC:
- Add EC host command support using rpmsg
- Add new CrOS USB PD logging driver
- Transfer spi messages at high priority
- Add support to trace CrOS EC commands
- Minor fixes and cleanups in protocol and debugfs
Wilco EC:
- Standardize Wilco EC mailbox interface
- Add h1_gpio status to debugfs"
* tag 'tag-chrome-platform-for-v5.2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux:
platform/chrome: cros_ec_proto: Add trace event to trace EC commands
platform/chrome: cros_ec_debugfs: Use cros_ec_cmd_xfer_status helper
platform/chrome: cros_ec: Add EC host command support using rpmsg
platform/chrome: wilco_ec: Add h1_gpio status to debugfs
platform/chrome: wilco_ec: Standardize mailbox interface
platform/chrome: cros_ec_proto: check for NULL transfer function
platform/chrome: Add CrOS USB PD logging driver
platform/chrome: cros_ec_spi: Transfer messages at high priority
platform/chrome: cros_ec_debugfs: no need to check return value of debugfs_create functions
platform/chrome: cros_ec_debugfs: Remove dev_warn when console log is not supported
Subsystem:
- set_mmss and set_mmss64 rtc_ops removal
- Fix timestamp value for RTC_TIMESTAMP_BEGIN_1900
- Use SPDX identifier for the core
- validate upper bound of tm->tm_year
New driver:
- Aspeed BMC SoC RTC
Drivers:
- abx80x: use rtc_add_group
- ds3232: nvram support
- pcf85063: add alarm, nvram, offset correction and microcrystal rv8263 support
- x1205: add of_match_table
- Use set_time instead of set_mms/set_mmss64 for: ab3100, coh901331, digicolor,
ds1672, ds2404, ep93xx, imxdi, jz4740, lpc32xx, mc13xxx, mxc, pcap, stmp3xxx,
test, wm831x, xgene.
- Set RTC range for: ab3100, at91sam9, coh901331, da9063, digicolor, dm355evm,
ds1672, ds2404, ep39xx, goldfish, imxdi, jz4740, lpc32xx, mc13xxx, mv, mxc,
omap, pcap, pcf85063, pcf85363, ps3, sh, stmp3xxx, sun4v, tegra, wm831x,
xgene.
- Switch to rtc_time64_to_tm/rtc_tm_to_time64 for the driver that properly set
the RTC range.
- Use dev_get_drvdata instead of multiple indirections.
-----BEGIN PGP SIGNATURE-----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=NyAx
-----END PGP SIGNATURE-----
Merge tag 'rtc-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"A huge series from me this cycle. I went through many drivers to set
the date and time range supported by the RTC which helps solving HW
limitation when the time comes (as early as next year for some). This
time, I focused on drivers using .set_mms and .set_mmss64, allowing me
to remove those callbacks. About a third of the patches got reviews, I
actually own the RTCs and I tested another third and the remaining one
are unlikely to cause any issues.
Other than that, a single new driver and the usual fixes here and there.
Summary:
Subsystem:
- set_mmss and set_mmss64 rtc_ops removal
- Fix timestamp value for RTC_TIMESTAMP_BEGIN_1900
- Use SPDX identifier for the core
- validate upper bound of tm->tm_year
New driver:
- Aspeed BMC SoC RTC
Drivers:
- abx80x: use rtc_add_group
- ds3232: nvram support
- pcf85063: add alarm, nvram, offset correction and microcrystal
rv8263 support
- x1205: add of_match_table
- Use set_time instead of set_mms/set_mmss64 for: ab3100, coh901331,
digicolor, ds1672, ds2404, ep93xx, imxdi, jz4740, lpc32xx, mc13xxx,
mxc, pcap, stmp3xxx, test, wm831x, xgene.
- Set RTC range for: ab3100, at91sam9, coh901331, da9063, digicolor,
dm355evm, ds1672, ds2404, ep39xx, goldfish, imxdi, jz4740, lpc32xx,
mc13xxx, mv, mxc, omap, pcap, pcf85063, pcf85363, ps3, sh,
stmp3xxx, sun4v, tegra, wm831x, xgene.
- Switch to rtc_time64_to_tm/rtc_tm_to_time64 for the driver that
properly set the RTC range.
- Use dev_get_drvdata instead of multiple indirections"
* tag 'rtc-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (177 commits)
rtc: snvs: Use __maybe_unused instead of #if CONFIG_PM_SLEEP
rtc: imxdi: remove unused variable
rtc: drop set_mms and set_mmss64
rtc: pcap: convert to SPDX identifier
rtc: pcap: use .set_time
rtc: pcap: switch to rtc_time64_to_tm/rtc_tm_to_time64
rtc: pcap: set range
rtc: digicolor: convert to SPDX identifier
rtc: digicolor: use .set_time
rtc: digicolor: set range
rtc: digicolor: fix possible race condition
rtc: jz4740: convert to SPDX identifier
rtc: jz4740: rework invalid time detection
rtc: jz4740: use dev_pm_set_wake_irq() to simplify code
rtc: jz4740: use .set_time
rtc: jz4740: remove useless check
rtc: jz4740: switch to rtc_time64_to_tm/rtc_tm_to_time64
rtc: jz4740: set range
rtc: 88pm860x: prevent use-after-free on device remove
rtc: Use dev_get_drvdata()
...
Use __maybe_unused for power management related functions
instead of #if CONFIG_PM_SLEEP to simply the code.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This variable is no longer used and the compiler rightly complains that
it should be removed.
../drivers/rtc/rtc-imxdi.c: In function ‘dryice_rtc_set_alarm’:
../drivers/rtc/rtc-imxdi.c:633:16: warning: unused variable ‘now’ [-Wunused-variable]
unsigned long now;
^~~
Rework to remove the unused variable.
Fixes: 629d488a3e ("rtc: imxdi: remove unnecessary check")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
There are no users of set_mms and set_mmss64 as they have all been
converted to set_time and are handling the tm to time conversion on their
own.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Call the 64bit versions of rtc_tm time conversion now that the range is
enforced by the core.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
While PCAP_RTC_DAY_MASK is set to 0x3ffff, it is very unlikely to be
correct as this ends in june 1992, before the product even existed. It is
more likely to be a 14-bit day counter. The next product in the family (the
mc13xxx) has a 15-bit day counter.
The same issue is seen with PCAP_RTC_TOD_MASK which only has 65535 seconds
and falls short of the necessary 86400 seconds.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Use .set_time instead of the deprecated .set_mmss.
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
While the range of REFERENCE + TIME is actually 33 bits, the counter
itself (TIME) is a 32-bits seconds counter.
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The IRQ is requested before the struct rtc is allocated and registered, but
this struct is used in the IRQ handler. This may lead to a NULL pointer
dereference.
Switch to devm_rtc_allocate_device/rtc_register_device to allocate the rtc
struct before requesting the IRQ.
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Using scripts/coccinelle/api/stream_open.cocci added in 10dce8af34
("fs: stream_open - opener for stream-like files so that read and write
can run simultaneously without deadlock"), search and convert to
stream_open all in-kernel nonseekable_open users for which read and
write actually do not depend on ppos and where there is no other methods
in file_operations which assume @offset access.
I've verified each generated change manually - that it is correct to convert -
and each other nonseekable_open instance left - that it is either not correct
to convert there, or that it is not converted due to current stream_open.cocci
limitations. The script also does not convert files that should be valid to
convert, but that currently have .llseek = noop_llseek or generic_file_llseek
for unknown reason despite file being opened with nonseekable_open (e.g.
drivers/input/mousedev.c)
Among cases converted 14 were potentially vulnerable to read vs write deadlock
(see details in 10dce8af34):
drivers/char/pcmcia/cm4000_cs.c:1685:7-23: ERROR: cm4000_fops: .read() can deadlock .write(); change nonseekable_open -> stream_open to fix.
drivers/gnss/core.c:45:1-17: ERROR: gnss_fops: .read() can deadlock .write(); change nonseekable_open -> stream_open to fix.
drivers/hid/uhid.c:635:1-17: ERROR: uhid_fops: .read() can deadlock .write(); change nonseekable_open -> stream_open to fix.
drivers/infiniband/core/user_mad.c:988:1-17: ERROR: umad_fops: .read() can deadlock .write(); change nonseekable_open -> stream_open to fix.
drivers/input/evdev.c:527:1-17: ERROR: evdev_fops: .read() can deadlock .write(); change nonseekable_open -> stream_open to fix.
drivers/input/misc/uinput.c:401:1-17: ERROR: uinput_fops: .read() can deadlock .write(); change nonseekable_open -> stream_open to fix.
drivers/isdn/capi/capi.c:963:8-24: ERROR: capi_fops: .read() can deadlock .write(); change nonseekable_open -> stream_open to fix.
drivers/leds/uleds.c:77:1-17: ERROR: uleds_fops: .read() can deadlock .write(); change nonseekable_open -> stream_open to fix.
drivers/media/rc/lirc_dev.c:198:1-17: ERROR: lirc_fops: .read() can deadlock .write(); change nonseekable_open -> stream_open to fix.
drivers/s390/char/fs3270.c:488:1-17: ERROR: fs3270_fops: .read() can deadlock .write(); change nonseekable_open -> stream_open to fix.
drivers/usb/misc/ldusb.c:310:1-17: ERROR: ld_usb_fops: .read() can deadlock .write(); change nonseekable_open -> stream_open to fix.
drivers/xen/evtchn.c:667:8-24: ERROR: evtchn_fops: .read() can deadlock .write(); change nonseekable_open -> stream_open to fix.
net/batman-adv/icmp_socket.c:80:1-17: ERROR: batadv_fops: .read() can deadlock .write(); change nonseekable_open -> stream_open to fix.
net/rfkill/core.c:1146:8-24: ERROR: rfkill_fops: .read() can deadlock .write(); change nonseekable_open -> stream_open to fix.
and the rest were just safe to convert to stream_open because their read and
write do not use ppos at all and corresponding file_operations do not
have methods that assume @offset file access(*):
arch/powerpc/platforms/52xx/mpc52xx_gpt.c:631:8-24: WARNING: mpc52xx_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
arch/powerpc/platforms/cell/spufs/file.c:591:8-24: WARNING: spufs_ibox_fops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
arch/powerpc/platforms/cell/spufs/file.c:591:8-24: WARNING: spufs_ibox_stat_fops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
arch/powerpc/platforms/cell/spufs/file.c:591:8-24: WARNING: spufs_mbox_fops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
arch/powerpc/platforms/cell/spufs/file.c:591:8-24: WARNING: spufs_mbox_stat_fops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
arch/powerpc/platforms/cell/spufs/file.c:591:8-24: WARNING: spufs_wbox_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
arch/powerpc/platforms/cell/spufs/file.c:591:8-24: WARNING: spufs_wbox_stat_fops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
arch/um/drivers/harddog_kern.c:88:8-24: WARNING: harddog_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
arch/x86/kernel/cpu/microcode/core.c:430:33-49: WARNING: microcode_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/char/ds1620.c:215:8-24: WARNING: ds1620_fops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/char/dtlk.c:301:1-17: WARNING: dtlk_fops: .read() and .write() have stream semantic; safe to change nonseekable_open -> stream_open.
drivers/char/ipmi/ipmi_watchdog.c:840:9-25: WARNING: ipmi_wdog_fops: .read() and .write() have stream semantic; safe to change nonseekable_open -> stream_open.
drivers/char/pcmcia/scr24x_cs.c:95:8-24: WARNING: scr24x_fops: .read() and .write() have stream semantic; safe to change nonseekable_open -> stream_open.
drivers/char/tb0219.c:246:9-25: WARNING: tb0219_fops: .read() and .write() have stream semantic; safe to change nonseekable_open -> stream_open.
drivers/firewire/nosy.c:306:8-24: WARNING: nosy_ops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/hwmon/fschmd.c:840:8-24: WARNING: watchdog_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/hwmon/w83793.c:1344:8-24: WARNING: watchdog_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/infiniband/core/ucma.c:1747:8-24: WARNING: ucma_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/infiniband/core/ucm.c:1178:8-24: WARNING: ucm_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/infiniband/core/uverbs_main.c:1086:8-24: WARNING: uverbs_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/input/joydev.c:282:1-17: WARNING: joydev_fops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/pci/switch/switchtec.c:393:1-17: WARNING: switchtec_fops: .read() and .write() have stream semantic; safe to change nonseekable_open -> stream_open.
drivers/platform/chrome/cros_ec_debugfs.c:135:8-24: WARNING: cros_ec_console_log_fops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/rtc/rtc-ds1374.c:470:9-25: WARNING: ds1374_wdt_fops: .read() and .write() have stream semantic; safe to change nonseekable_open -> stream_open.
drivers/rtc/rtc-m41t80.c:805:9-25: WARNING: wdt_fops: .read() and .write() have stream semantic; safe to change nonseekable_open -> stream_open.
drivers/s390/char/tape_char.c:293:2-18: WARNING: tape_fops: .read() and .write() have stream semantic; safe to change nonseekable_open -> stream_open.
drivers/s390/char/zcore.c:194:8-24: WARNING: zcore_reipl_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/s390/crypto/zcrypt_api.c:528:8-24: WARNING: zcrypt_fops: .read() and .write() have stream semantic; safe to change nonseekable_open -> stream_open.
drivers/spi/spidev.c:594:1-17: WARNING: spidev_fops: .read() and .write() have stream semantic; safe to change nonseekable_open -> stream_open.
drivers/staging/pi433/pi433_if.c:974:1-17: WARNING: pi433_fops: .read() and .write() have stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/acquirewdt.c:203:8-24: WARNING: acq_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/advantechwdt.c:202:8-24: WARNING: advwdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/alim1535_wdt.c:252:8-24: WARNING: ali_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/alim7101_wdt.c:217:8-24: WARNING: wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/ar7_wdt.c:166:8-24: WARNING: ar7_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/at91rm9200_wdt.c:113:8-24: WARNING: at91wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/ath79_wdt.c:135:8-24: WARNING: ath79_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/bcm63xx_wdt.c:119:8-24: WARNING: bcm63xx_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/cpu5wdt.c:143:8-24: WARNING: cpu5wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/cpwd.c:397:8-24: WARNING: cpwd_fops: .read() and .write() have stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/eurotechwdt.c:319:8-24: WARNING: eurwdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/f71808e_wdt.c:528:8-24: WARNING: watchdog_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/gef_wdt.c:232:8-24: WARNING: gef_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/geodewdt.c:95:8-24: WARNING: geodewdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/ib700wdt.c:241:8-24: WARNING: ibwdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/ibmasr.c:326:8-24: WARNING: asr_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/indydog.c:80:8-24: WARNING: indydog_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/intel_scu_watchdog.c:307:8-24: WARNING: intel_scu_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/iop_wdt.c:104:8-24: WARNING: iop_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/it8712f_wdt.c:330:8-24: WARNING: it8712f_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/ixp4xx_wdt.c:68:8-24: WARNING: ixp4xx_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/ks8695_wdt.c:145:8-24: WARNING: ks8695wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/m54xx_wdt.c:88:8-24: WARNING: m54xx_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/machzwd.c:336:8-24: WARNING: zf_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/mixcomwd.c:153:8-24: WARNING: mixcomwd_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/mtx-1_wdt.c:121:8-24: WARNING: mtx1_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/mv64x60_wdt.c:136:8-24: WARNING: mv64x60_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/nuc900_wdt.c:134:8-24: WARNING: nuc900wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/nv_tco.c:164:8-24: WARNING: nv_tco_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/pc87413_wdt.c:289:8-24: WARNING: pc87413_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/pcwd.c:698:8-24: WARNING: pcwd_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/pcwd.c:737:8-24: WARNING: pcwd_temp_fops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/pcwd_pci.c:581:8-24: WARNING: pcipcwd_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/pcwd_pci.c:623:8-24: WARNING: pcipcwd_temp_fops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/pcwd_usb.c:488:8-24: WARNING: usb_pcwd_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/pcwd_usb.c:527:8-24: WARNING: usb_pcwd_temperature_fops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/pika_wdt.c:121:8-24: WARNING: pikawdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/pnx833x_wdt.c:119:8-24: WARNING: pnx833x_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/rc32434_wdt.c:153:8-24: WARNING: rc32434_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/rdc321x_wdt.c:145:8-24: WARNING: rdc321x_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/riowd.c:79:1-17: WARNING: riowd_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/sa1100_wdt.c:62:8-24: WARNING: sa1100dog_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/sbc60xxwdt.c:211:8-24: WARNING: wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/sbc7240_wdt.c:139:8-24: WARNING: wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/sbc8360.c:274:8-24: WARNING: sbc8360_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/sbc_epx_c3.c:81:8-24: WARNING: epx_c3_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/sbc_fitpc2_wdt.c:78:8-24: WARNING: fitpc2_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/sb_wdog.c:108:1-17: WARNING: sbwdog_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/sc1200wdt.c:181:8-24: WARNING: sc1200wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/sc520_wdt.c:261:8-24: WARNING: wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/sch311x_wdt.c:319:8-24: WARNING: sch311x_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/scx200_wdt.c:105:8-24: WARNING: scx200_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/smsc37b787_wdt.c:369:8-24: WARNING: wb_smsc_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/w83877f_wdt.c:227:8-24: WARNING: wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/w83977f_wdt.c:301:8-24: WARNING: wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/wafer5823wdt.c:200:8-24: WARNING: wafwdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/watchdog_dev.c:828:8-24: WARNING: watchdog_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/wdrtas.c:379:8-24: WARNING: wdrtas_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/wdrtas.c:445:8-24: WARNING: wdrtas_temp_fops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/wdt285.c:104:1-17: WARNING: watchdog_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/wdt977.c:276:8-24: WARNING: wdt977_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/wdt.c:424:8-24: WARNING: wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/wdt.c:484:8-24: WARNING: wdt_temp_fops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/wdt_pci.c:464:8-24: WARNING: wdtpci_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/wdt_pci.c:527:8-24: WARNING: wdtpci_temp_fops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
net/batman-adv/log.c:105:1-17: WARNING: batadv_log_fops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
sound/core/control.c:57:7-23: WARNING: snd_ctl_f_ops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
sound/core/rawmidi.c:385:7-23: WARNING: snd_rawmidi_f_ops: .read() and .write() have stream semantic; safe to change nonseekable_open -> stream_open.
sound/core/seq/seq_clientmgr.c:310:7-23: WARNING: snd_seq_f_ops: .read() and .write() have stream semantic; safe to change nonseekable_open -> stream_open.
sound/core/timer.c:1428:7-23: WARNING: snd_timer_f_ops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
One can also recheck/review the patch via generating it with explanation comments included via
$ make coccicheck MODE=patch COCCI=scripts/coccinelle/api/stream_open.cocci SPFLAGS="-D explain"
(*) This second group also contains cases with read/write deadlocks that
stream_open.cocci don't yet detect, but which are still valid to convert to
stream_open since ppos is not used. For example drivers/pci/switch/switchtec.c
calls wait_for_completion_interruptible() in its .read, but stream_open.cocci
currently detects only "wait_event*" as blocking.
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Yongzhi Pan <panyongzhi@gmail.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: Tejun Heo <tj@kernel.org>
Cc: Kirill Tkhai <ktkhai@virtuozzo.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Nikolaus Rath <Nikolaus@rath.org>
Cc: Han-Wen Nienhuys <hanwen@google.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "James R. Van Zandt" <jrv@vanzandt.mv.com>
Cc: Corey Minyard <minyard@acm.org>
Cc: Harald Welte <laforge@gnumonks.org>
Acked-by: Lubomir Rintel <lkundrak@v3.sk> [scr24x_cs]
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Johan Hovold <johan@kernel.org>
Cc: David Herrmann <dh.herrmann@googlemail.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: Jean Delvare <jdelvare@suse.com>
Acked-by: Guenter Roeck <linux@roeck-us.net> [watchdog/* hwmon/*]
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Acked-by: Logan Gunthorpe <logang@deltatee.com> [drivers/pci/switch/switchtec]
Acked-by: Bjorn Helgaas <bhelgaas@google.com> [drivers/pci/switch/switchtec]
Cc: Benson Leung <bleung@chromium.org>
Acked-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> [platform/chrome]
Cc: Alessandro Zummo <a.zummo@towertech.it>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com> [rtc/*]
Cc: Mark Brown <broonie@kernel.org>
Cc: Wim Van Sebroeck <wim@linux-watchdog.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Zwane Mwaikambo <zwanem@gmail.com>
Cc: Marek Lindner <mareklindner@neomailbox.ch>
Cc: Simon Wunderlich <sw@simonwunderlich.de>
Cc: Antonio Quartulli <a@unstable.cc>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Signed-off-by: Kirill Smelkov <kirr@nexedi.com>
The scratchpad register is used to detect an invalid time when power to the
RTC has been lost. Instead of deleting that precious information and set
the time to the UNIX epoch, forward it to userspace.
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Use dev_pm_set_wake_irq() to set the RTC as a wakeup source for suspend.
This allows to remove the whole dev_pm_ops structure.
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Use .set_time instead of the deprecated .set_mmss.
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
rtc_time64_to_tm always returns a valid tm, it is not necessary to validate
it.
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Call the 64bit versions of rtc_tm time conversion now that the range is
enforced by the core.
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The device's remove() attempts to shut down the delayed_work scheduled
on the kernel-global workqueue by calling flush_scheduled_work().
Unfortunately, flush_scheduled_work() does not prevent the delayed_work
from re-scheduling itself. The delayed_work might run after the device
has been removed, and touch the already de-allocated info structure.
This is a potential use-after-free.
Fix by calling cancel_delayed_work_sync() during remove(): this ensures
that the delayed work is properly cancelled, is no longer running, and
is not able to re-schedule itself.
This issue was detected with the help of Coccinelle.
Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The RTC core already ensures the alarm is set to a time in the future, it
is not necessary to check again in the driver.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Call the 64bit versions of rtc_tm time conversion now that the range is
enforced by the core.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The RTC Time Counter MSB Register contains the 32 most significant bits
(47:16) of the 47-bit RTC Time Counter. Clocked by a 32.768 KHz clock, this
register is effectively a 32-bit seconds counter.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Let the core handle the range, and in particular the imx1 offsetting. This
has the benefit of extending the range of the RTC further than 365 days and
making .read_time useful again on imx1.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The IRQ is requested before the struct rtc is allocated and registered, but
this struct is used in the IRQ handler. This may lead to a NULL pointer
dereference.
Switch to devm_rtc_allocate_device/rtc_register_device to allocate the rtc
struct before requesting the IRQ.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Manage the -EPROBE_DEFER error case for the wake IRQ.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Acked-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add missing <of_device_id> table for SPI driver relying on SPI
device match since compatible is in a DT binding or in a DTS.
Before this patch:
modinfo drivers/rtc/rtc-rx6110.ko | grep alias
alias: spi:rx6110
After this patch:
modinfo drivers/rtc/rtc-rx6110.ko | grep alias
alias: spi:rx6110
alias: of:N*T*Cepson,rx6110C*
alias: of:N*T*Cepson,rx6110
Reported-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Daniel Gomez <dagmcr@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Use .set_time instead of the deprecated .set_mmss.
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
There is only one ds2404_chip_ops struct that is implemented, remove the
unnecessary indirection.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The real-time clock is a 5-byte binary counter. It is incremented 256 times
per second. The least significant byte is a count of fractional seconds.
The upper four bytes are a count of seconds. The realtime clock can
accumulate 136 years of seconds before rolling over.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Use rtc_add_group to add the sysfs group in a race free manner.
This has the side effect of moving the files to their proper location.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Since commit 28dc5f8038 ("drivers/rtc/rtc-ep93xx.c: use
dev_get_platdata()"), platform_data is not used directly, it is not
necessary to set it anymore.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
DS3232 RTC has 236 bytes of persistent memory.
Add RTC SRAM read and write access using
the NVMEM Framework.
Signed-off-by: Han Nandor <nandor.han@vaisala.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Handling of extended interrupts (kickstart, wake-up, ram-clear) was
moved off to a work queue, but the interrupts aren't acknowledged
in the interrupt handler. This leads to a deadlock, if driver
is used with interrupts. To fix this we use a threaded interrupt, get rid
of the work queue and do locking with just the rtc mutex lock.
Fixes: aaaf5fbf56 ("rtc: add driver for DS1685 family of real time clocks")
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
ds1685_rtc_begin_ctrl_access/ds1685_rtc_end_ctrl_access aren't used,
so get rid of it.
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The current API for the wilco EC mailbox interface is bad.
It assumes that most messages sent to the EC follow a similar structure,
with a command byte in MBOX[0], followed by a junk byte, followed by
actual data. This doesn't happen in several cases, such as setting the
RTC time, using the raw debugfs interface, and reading or writing
properties such as the Peak Shift policy (this last to be submitted soon).
Similarly for the response message from the EC, the current interface
assumes that the first byte of data is always 0, and the second byte
is unused. However, in both setting and getting the RTC time, in the
debugfs interface, and for reading and writing properties, this isn't
true.
The current way to resolve this is to use WILCO_EC_FLAG_RAW* flags to
specify when and when not to skip these initial bytes in the sent and
received message. They are confusing and used so much that they are
normal, and not exceptions. In addition, the first byte of
response in the debugfs interface is still always skipped, which is
weird, since this raw interface should be giving the entire result.
Additionally, sent messages assume the first byte is a command, and so
struct wilco_ec_message contains the "command" field. In setting or
getting properties however, the first byte is not a command, and so this
field has to be filled with a byte that isn't actually a command. This
is again inconsistent.
wilco_ec_message contains a result field as well, copied from
wilco_ec_response->result. The message result field should be removed:
if the message fails, the cause is already logged, and the callers are
alerted. They will never care about the actual state of the result flag.
These flags and different cases make the wilco_ec_transfer() function,
used in wilco_ec_mailbox(), really gross, dealing with a bunch of
different cases. It's difficult to figure out what it is doing.
Finally, making these assumptions about the structure of a message make
it so that the messages do not correspond well with the specification
for the EC's mailbox interface. For instance, this interface
specification may say that MBOX[9] in the received message contains
some information, but the calling code needs to remember that the first
byte of response is always skipped, and because it didn't set the
RESPONSE_RAW flag, the next byte is also skipped, so this information
is actually contained within wilco_ec_message->response_data[7]. This
makes it difficult to maintain this code in the future.
To fix these problems this patch standardizes the mailbox interface by:
- Removing the WILCO_EC_FLAG_RAW* flags
- Removing the command and reserved_raw bytes from wilco_ec_request
- Removing the mbox0 byte from wilco_ec_response
- Simplifying wilco_ec_transfer() because of these changes
- Gives the callers of wilco_ec_mailbox() the responsibility of exactly
and consistently defining the structure of the mailbox request and
response
- Removing command and result from wilco_ec_message.
This results in the reduction of total code, and makes it much more
maintainable and understandable.
Signed-off-by: Nick Crews <ncrews@chromium.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
sysfs entries added by rtc_add_group are called with the rtc device
as argument and not the underlying device. Fixed by using the dev->parent
Fixes: cfb74916e2 ("rtc: ds1685: use rtc_add_group")
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Call the 64bit versions of rtc_tm time conversion now that the range is
enforced by the core.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
With calling dev_pm_set_wake_irq() to set MXC_V2 RTC as wakeup source
for suspend, generic wake irq mechanism will automatically enable
it as wakeup source when suspend, then the suspend/resume callback
which are ONLY for enabling/disabling irq wake can be removed, it
simplifies the code.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
With calling dev_pm_set_wake_irq() to set MXC RTC as wakeup source
for suspend, generic wake irq mechanism will automatically enable
it as wakeup source when suspend, then the suspend/resume callback
which are ONLY for enabling/disabling irq wake can be removed, it
simplifies the code.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The commit 1921cab117 ("rtc: rx8025: Switch to use %ptR") converted
the driver to use new %p extension, but actually used wrong type of
the parameter in one case.
Fix a parameter to %ptR in rx8025_read_alarm().
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Fix sparse warning:
drivers/rtc/rtc-sirfsoc.c:282:28: warning:
symbol 'sysrtc_regmap_config' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Use .set_time instead of the deprecated .set_mmss64.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The ab3100 has a 48bit counter running at 65536 Hz (despite one of the
comment). The max value is then (2^48 - 1)/2^16 == 2^32 - 1.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
It is not necessary to forward declare pcf85363_driver as it is not used
before being declared.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
regmap is abstracting the i2c functionalities the best it can, there is no
need to check.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Call the 64bit versions of rtc_tm time conversion now that the range is
enforced by the core.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
From the datasheet: "HW_RTC_SECONDS provides access to the 32-bit real-time
seconds counter."
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Prepare rtc driver for rtc-only with DDR in self-refresh mode.
omap_rtc_power_off now should cater to two features:
1) RTC plus DDR in self-refresh is power a saving mode where in the
entire system including the different voltage rails from PMIC are
shutdown except the ones feeding on to RTC and DDR. DDR is kept in
self-refresh hence the contents are preserved. RTC ALARM2 is connected
to PMIC_EN line once we the ALARM2 is triggered we enter the mode with
DDR in self-refresh and RTC Ticking. After a predetermined time an RTC
ALARM1 triggers waking up the system[1]. The control goes to bootloader.
The bootloader then checks RTC scratchpad registers to confirm it was an
rtc_only wakeup and follows a different path, configure bare minimal
clocks for ddr and then jumps to the resume address in another RTC
scratchpad registers and transfers the control to Kernel. Kernel then
restores the saved context. omap_rtc_power_off_program does the ALARM2
programming part.
[1] http://www.ti.com/lit/ug/spruhl7h/spruhl7h.pdf Page 2884
2) Power-off: This is usual poweroff mode. omap_rtc_power_off calls the
above omap_rtc_power_off_program function and in addition to that
programs the OMAP_RTC_PMIC_REG for any external wake ups for PMIC like
the pushbutton and shuts off the PMIC.
Hence the split in omap_rtc_power_off.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
[tony@atomide.com: folded in a fix for compile warning]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Call the 64bit versions of rtc_tm time conversion now that the range is
enforced by the core.
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Use .set_time instead of the deprecated .set_mmss.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Call the 64bit versions of rtc_tm time conversion now that the range is
enforced by the core.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
ds1672_get_datetime and ds1672_set_mmss are only used after casting dev
to an i2c_client. Remove that useless indirection.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Remove the control sysfs file as it is not documented, read only and was
only used to provide the oscillator state.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Return -EINVAL when trying to read an invalid time instead of just probe
because this is a useful information for userspace.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The ds1672 is a 32bit seconds counter.
Also remove erroneous comment claiming that epoch is set to 2000, it was
not.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The mentioned function pointer is long gone since early 2011. Remove the
reference in the comment and reword it slightly.
Fixes: 51ba60c5bb ("RTC: Cleanup rtc_class_ops->update_irq_enable()")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Remove the unused "depends on I2C" as the config options are already
guarded by if I2C.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Allow reading the oscillator status bit. Also allow clearing it even if
that makes little sense and can't be done in a race free way.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The PCF850363 has an offset correction with two modes:
With mode 0, the correction is triggered once every two hours and then
correction pulses are applied once per minute until the programmed
correction values have been implemented. This gives a step of 4.34 ppm.
With mode 1, the correction is triggered once every four minutes and then
correction pulses are applied once per second up to a maximum of 60 pulses.
When correction values greater than 60 pulses are used, additional
correction pulses are made in the 59 th second. This gives a step of 4.069
ppm.
Use the correction closest to the requested value.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The Micro Crystal RV8263 has the same IC as the pcf85063 but has an on
board crystal. This means that the CAP_SEL bit has to be cleared so the
correct capacitance is selected for the crystal.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add support for the alarms. The match on the weekday is not used as it it
not necessarily properly set.
The tested RTC shows a behaviour where setting an alarm on the second right
after an alarm that fired is not working, probably because of the circuit
that ensures an alarm only fires once. This is why uie_unsupported is set.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
As stated in a comment pcf85063a and pcf85063tp don't have the same number
of registers. Especially, pcf85063tp doesn't have alarm support.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Switch to regmap to simplify register accesses and remove the need for
pcf85063_stop_clock/pcf85063_start_clock.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Only smbus reads and write are done in the driver, plain i2c functionality
is not required.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Use the new helper devm_platform_ioremap_resource() which wraps the
platform_get_resource() and devm_ioremap_resource() together, to
simplify the code.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Use the new helper devm_platform_ioremap_resource() which wraps the
platform_get_resource() and devm_ioremap_resource() together, to
simplify the code.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
With calling dev_pm_set_wake_irq() to set SNVS RTC as wakeup
source for suspend, generic wake irq mechanism will automatically
enable it as wakeup source when suspend, then the suspend/resume
callback which are ONLY for enabling/disabling irq wake can be
removed, it simplifies the code.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Read and writes the time to the non-battery backed RTC in the ASPEED BMC
system on chip families.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Call the 64bit version of rtc_time_to_tm as the range is enforced by the
core.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The IRQ mapping was changed to not being created in the rtc-mt6397
driver, so the irq_dispose_mapping is no longer needed.
Also the dev_id passed to free_irq should be the same as the last
argument passed to request_threaded_irq.
This prevents a "Trying to free already-free IRQ 274" warning when
unbinding the driver.
Fixes: e695d3a0b3 ("mfd: mt6397: Create irq mappings in mfd core driver")
Signed-off-by: Pi-Hsun Shih <pihsun@chromium.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Fix sparse warning:
drivers/rtc/rtc-opal.c:227:5:
warning: symbol 'opal_tpo_alarm_irq_enable' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Use SPDX-License-Identifier instead of a verbose license text.
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Call the 64bit versions of rtc_tm time conversion now that the range is
enforced by the core.
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
There is no specific handling in the error path of wm831x_rtc_probe, remove
the unnecessary goto and label.
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The wm831x has a 32bit second counter.
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Call the 64bit versions of rtc_tm time conversion now that the range is
enforced by the core.
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The DA9062 and DA9063 have a year register that can go up to 0x3F.
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Use SPDX-License-Identifier to be clearer on the license. Choose the v2
only as this is the default Linux license.
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The Sun4v Hypervisor Core API Specification states:
Time is described by a single unsigned 64-bit word equivalent to a time_t
for the POSIX time(2) system call. The word contains the time since the
Epoch (00:00:00 UTC, January 1, 1970), measured in seconds.
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Call the 64bit versions of rtc_tm time conversion as the hypervisor handles
64bit values.
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The PS3 has a 64bit second counter from 2000. While this exceeds the 64bit
UNIX timestamp, there is not doubt that non of them will still be working
by then.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Use SPDX-License-Identifier instead of a verbose license text
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Call the 64bit versions of rtc_tm time conversion as the range is enforced
by the core.
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The AT91 RTT is a 32bit second counter that is saved in a 32bit global
purpose register.
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Alexandre Belloni