To add the core part for the MMC power sequence, let's start by adding
initial support for the simple MMC power sequence provider.
In this initial step, the MMC power sequence node are fetched and the
compatible string for the simple MMC power sequence provider are
verified.
At this point we don't parse the node for any properties, but instead
that will be handled from following patches. Since there are no
properties supported yet, let's just implement the ->alloc() and the
->free() callbacks.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
System on chip designs may specify a specific MMC power sequence. To
successfully detect an (e)MMC/SD/SDIO card, that power sequence must
be followed while initializing the card.
To be able to handle these SOC specific power sequences, let's add a
MMC power sequence interface. It provides the following functions to
help the mmc core to deal with these power sequences.
mmc_pwrseq_alloc() - Invoked from mmc_of_parse(), to initialize data.
mmc_pwrseq_pre_power_on()- Invoked in the beginning of mmc_power_up().
mmc_pwrseq_post_power_on()- Invoked at the end in mmc_power_up().
mmc_pwrseq_power_off()- Invoked from mmc_power_off().
mmc_pwrseq_free() - Invoked from mmc_free_host(), to free data.
Each MMC power sequence provider will be responsible to implement a set
of callbacks. These callbacks mirrors the functions above.
This patch adds the skeleton, following patches will extend the core of
the MMC power sequence and add support for a specific simple MMC power
sequence.
Do note, since the mmc_pwrseq_alloc() is invoked from mmc_of_parse(),
host drivers needs to make use of this API to enable the support for
MMC power sequences. Moreover the MMC power sequence support depends on
CONFIG_OF.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Commit 63589e92c2 ("clk: Ignore error and NULL pointers passed to
clk_{unprepare, disable}()") allows NULL or error pointer to be passed
unconditionally.
This patch is to simplify probe error and remove code paths.
However, we reserve the core clock checks in runtime suspend/resume code
because we want a little smaller latency.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Check sg_count before sending long data xfer.
Because dma_map_sg() return int, and sg_count may be negative,
so using int instead of unsigned.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Return error-code directly if no card exist, this can
make card remove faster.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
drivers/mmc/host/sdhci_f_sdh30.c:143:5-11: inconsistent IS_ERR and PTR_ERR, PTR_ERR on line 144
PTR_ERR should access the value just tested by IS_ERR
Semantic patch information:
There can be false positives in the patch case, where it is the call
IS_ERR that is wrong.
Generated by: scripts/coccinelle/tests/odd_ptr_err.cocci
CC: Vincent Yang <vincent.yang.fujitsu@gmail.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fixed the following warning (reported by cppcheck):
[drivers/mmc/card/block.c:2149]: (warning) %d in format string (no. 1)
requires 'int' but the argument type is 'unsigned int'.
Signed-off-by: Asaf Vertz <asaf.vertz@tandemg.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
tmio_mmc_host has .enable_dma callback now.
We don't need TMIO_MMC_HAVE_CTL_DMA_REG anymore.
Let's remove it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now, sh_mobile_sdhi can use 32bit DMA access in R-Cer Gen2.
Let's use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
getting struct sh_mobile_sdhi from struct mmc_host needs to use
complex container_of(). This patch adds new host_to_priv macro to
get it easily.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Latest SDHI on Renesas has expand register mapping.
update mmc_data->bus_shift for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
No one is using .init/.cleanup callback function.
Let's remove these.
sdhi_ops and .cd_wakeup are also removed
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Renesas SDHI which is based on TMIO driver has 2 type SoC. 1st one is
used as SH-Mobile series, and 2nd is R-Car series. R-Car series SoC has
DMA buswidth setting register which enables 32bit access.
This patch adds .dma_buswidth and enables it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some controllers need DMA special register/setting.
This patch adds new .enable_dma callback for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current .dma_rx_offset is implemented under tmio_mmc_dma.
It goes to tmio_mmc_data by this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current .alignment_shift is implemented under tmio_mmc_dma.
It goes to tmio_mmc_data by this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current .bus_shift is implemented under tmio_mmc_data.
It goes to tmio_mmc_host by this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current .multi_io_quirk is implemented under tmio_mmc_data.
It goes to tmio_mmc_host by this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current .clk_disable is implemented under tmio_mmc_data.
It goes to tmio_mmc_host by this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current .clk_enable is implemented under tmio_mmc_data.
It goes to tmio_mmc_host by this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current .write16_hook is implemented under tmio_mmc_data.
It goes to tmio_mmc_host by this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current .dma is implemented under tmio_mmc_data.
It goes to tmio_mmc_host by this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current tmio_mmc driver is using tmio_mmc_data for driver/platform
specific data/callback, and it is needed for tmio_mmc_host_probe()
function. Because of this style, include/linux/mfd/tmio.h header has
tmio driver/framework specific data which is not needed from platform.
This patch adds new tmio_mmc_host_alloc/free() as cleanup preparation.
tmio driver specific data/callback will be implemented in tmio_mmc_host,
and platform specific data/callback will be implemented in tmio_mmc_data
in this cleanup.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds new host controller driver for
Fujitsu SDHCI controller f_sdh30.
Signed-off-by: Vincent Yang <Vincent.Yang@tw.fujitsu.com>
Signed-off-by: Andy Green <andy.green@linaro.org>
Signed-off-by: Tetsuya Takinishi <t.takinishi@jp.fujitsu.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch defines a quirk to disable the block count
for single block transactions.
It is a preparation and will be used by Fujitsu
SDHCI controller f_sdh30 driver.
Signed-off-by: Vincent Yang <Vincent.Yang@tw.fujitsu.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch defines a quirk for tuning work
around for some sdhci host controller. It sets
both SDHCI_CTRL_EXEC_TUNING and SDHCI_CTRL_TUNED_CLK
for tuning.
It is a preparation and will be used by Fujitsu
SDHCI controller f_sdh30 driver.
Signed-off-by: Vincent Yang <Vincent.Yang@tw.fujitsu.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds a callback function to do
controller-specific actions when switching voltages.
It is a preparation and will be used by Fujitsu
SDHCI controller f_sdh30 driver.
Signed-off-by: Vincent Yang <Vincent.Yang@tw.fujitsu.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If we power up vqmmc in MMC_POWER_ON then we end up turning it on
before mmc_power_up() sets the signal voltage. That's not so great
since we might be powering it up at the wrong voltage.
Note that this is how Yuvaraj originally coded things up in
<https://patchwork.kernel.org/patch/4401231/> but he changed it on my
suggestion. Apparently I was wrong.
Reported-by: Alexandru M Stan <amstan@chromium.org>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch solves the coding style issue by adding a space
before (
Signed-off-by: Mohammad Jamal <md.jamalmohiuddin@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch calls pm_runtime_put_noidle() to restore the device's usage
counter in the ->remove() implementation.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 0dcaa2499b ("sdhci-pxav3: Fix runtime PM initialization") tries
to fix one hang issue caused by calling sdhci_add_host() on a suspended
device. The fix enables the clock twice, once by clk_prepare_enable() and
another by pm_runtime_get_sync(), meaning that the clock will never be
gated at runtime PM suspend. I observed the power consumption regression on
Marvell BG2Q SoCs.
In fact, the fix is not correct. There still be a very small window
during which a runtime suspend might somehow occur after pm_runtime_enable()
but before pm_runtime_get_sync().
This patch fixes all of the two problems by just incrementing the usage
counter before pm_runtime_enable(). It also adjust the order of disabling
runtime pm and storing the usage count in the error path to handle clock
gating properly.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Cc: <stable@vger.kernel.org> # v3.11+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is no point making the initialization
of buf_ready_int conditional on host version.
Simplify by just doing it always. Note that
the other conditional initializations will be
removed when the new way of doing re-tuning
is taken into use.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Both callers of mmc_start_request() call mmc_card_removed()
so move that call into mmc_start_request().
This patch is preparation for adding re-tuning support.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For each MMC, SD and SDIO there is code that
holds the clock, calls ops->execute_tuning, and
releases the clock. Simplify the code a bit by
providing a separate function to do that.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This ensures that all standard options are available to hsmmc,
In particular, I need cap-power-off-card.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Using the common code removes some code duplication, and
makes it easier to switch to using mmc_of_parse() which
will remove more duplication.
This uses the new mmc_gpio_request_cd_isr to provide a non-standard
interrupt service routine for card-detect interrupts.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
One of the reasons omap_hsmmc doesn't use the slot-gpio library
is that it has some non-standard functionality in the card-detect
interrupt service routine.
To make it possible for omap_hsmmc (and maybe others) to be converted
to use slot-gpio, add 'mmc_gpio_request_cd_isr' which provide an
alternate isr to be register by the slot-gpio code.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Just fix the comments, no functional changes.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Enable power cycle and re-initialization of SD cards via the reset
bus_ops. Power cycling a buggy SD card sometimes helps it get back on
track.
Signed-off-by: Johan Rudholm <johanru@axis.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Move the (e)MMC specific hw_reset code from core.c into mmc.c. Call the
code from the new bus_ops member "reset". This also allows for adding
a SD card specific reset procedure.
Signed-off-by: Johan Rudholm <johanru@axis.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Always check if the card is alive after a successful reset. This allows
us to remove mmc_hw_reset_check(), leaving mmc_hw_reset() as the only
card reset interface.
Signed-off-by: Johan Rudholm <johanru@axis.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This adds SDIO devicetree subnode parsing to the mmc core. While
SDIO devices are runtime probable they sometimes need nonprobable
additional information on embedded systems, like an additional gpio
interrupt or a clock. This patch makes it possible to supply this
information from the devicetree. SDIO drivers will find a pointer
to the devicenode in their devices of_node pointer.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
[hdegoede@redhat.com: Misc. cleanups]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch is based on the patches by Per Forlin, Tony Lin and Ryan QIAN.
This patch complete the API 'post_req' and 'pre_req' in sdhci host side,
Test Env:
1. i.MX6Q-SABREAUTO board, CPU @ 996MHz, use ADMA in uSDHC controller.
2. Test command:
$ echo 1 > /proc/sys/vm/drop_caches
write to sd card:
$ dd if=/dev/zero of=/dev/mmcblk0 bs=1M count=2000 conv=fsync
read the sd card:
$ dd if=/dev/mmcblk0 of=/dev/null bs=1M count=2000
3. TOSHIBA 16GB SD3.0 card, running at 4 bit, SDR104 @ 198MHZ
Performance with and without this patch:
-------------------------------------------------
| | read speed | write speed |
|------------------------------------------------
| with this patch | ~76.7 MB/s | ~23.3 MB/s |
|------------------------------------------------
|without this patch | ~60.5 MB/s | ~22.5 MB/s |
-------------------------------------------------
4. SanDisk 8GB SD3.0 card, running at 4 bit, DDR50 @ 50MHZ
Performance with and without this patch:
-------------------------------------------------
| | read speed | write speed |
|------------------------------------------------
| with this patch | ~40.5 MB/s | ~15.6 MB/s |
|------------------------------------------------
|without this patch | ~36.1 MB/s | ~14.1 MB/s |
-------------------------------------------------
5. Kingston 8GB SD2.0 card, running at 4 bit, High-speed @ 50MHZ
Performance with and without this patch:
-------------------------------------------------
| | read speed | write speed |
|------------------------------------------------
| with this patch | ~22.7 MB/s | ~8.2 MB/s |
|------------------------------------------------
|without this patch | ~21.3 MB/s | ~8.0 MB/s |
-------------------------------------------------
6. About eMMC, Sandisk 8GB eMMC on i.MX6DL-sabresd board, CPU @ 792MHZ,
eMMC running at 8 bit, DDR52 @ 52MHZ.
Performance with and without this patch:
-------------------------------------------------
| | read speed | write speed |
|------------------------------------------------
| with this patch | ~37.3 MB/s | ~10.5 MB/s |
|------------------------------------------------
|without this patch | ~33.4 MB/s | ~10.5 MB/s |
-------------------------------------------------
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The bounce buffer, used for misaligned bytes for ADMA access,
resides wholly within the (align_sz)-aligned word, just by construction.
The page addresses are aligned to (align_sz), either for 4 or 8 bytes
alignment, so that the aligned word resides wholly within a single page
and can't cross the page boundary. So, the bounce buffer can't cross
the page boundary too. That's why the warnings are never hit, and can
be safely removed.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since previous patches removed the need for the tuning block patterns
to be exported, let's move them close to the mmc_send_tuning() API.
Those are now intended to be used only by the mmc core.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Instead of having a local hack taking care of sending the tuning
command and as well to verify the response pattern, let's convert to
the common mmc_send_tuning() API.
This change affects the Exynos variant, since it's the only one which
support the dw_mmc's ->execute_tuning() callback.
It's seems like dw_mmc internal logic expects failed data transfers to
be ended using a stop command. Let the tuning requests also fall into
this category, since there are data transfer involved.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Previously the pm_runtime_put() caused the device to be runtime PM
suspended, but then immediately being resumed when we add the host.
Prevent this unnecessary runtime PM suspend/resume cycle during
->probe() by moving the call to pm_runtime_put() after mmc_add_host().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
By configure runtime PM prior we enable the use of it, we close the gap
for strange and unhandled conditions. Moreover it makes us rely on the
driver core, after finalized ->probe(), to request an inactive device
to become runtime PM idle/suspended, which earlier potentially could
happen already at pm_runtime_set_autosuspend_delay().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since sdhci_remove_host() access the device, we need to make sure it's
runtime PM resumed.
To handle clock gating properly in remove, we first have to make sure
the clocks are ungated.
To fix both these issues, by invoking pm_runtime_get_sync() early in
->remove() callback. Later once we disabled runtime PM, we can restore
the usage count.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since commit ab78029ecc (drivers/pinctrl: grab default handles from device
core), we can rely on device core for setting the default pins.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Modify transfer mode for support sdio card,
send cmd and data at the same time for read data transfer,
but send data after cmd for write data transfer.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To support sdio card, transfer mode need make a change,
this need to split code and use it in different place,
Add new function to simplify repeat operation.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
host->cookie is used for handle async request,
we should init it to negative value when new card inserted,
make cookie value invalid.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a new function to dump register within a range.
We print 1 register a line before this patch,
this may make debug info too long when we add more register to dump.
The new dump_reg_range() dump to 8 register a line,
and it is easy to use.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
By moving the allocation of the slot-gpio data into mmc_alloc_host(),
we can remove the slot-gpio internal calls to mmc_gpio_alloc().
This means mmc_gpio_alloc() has now only one caller left, which
consequence allow us to simplify and remove some of the slot-gpio code.
Additionally, this makes the slot-gpio mutex redundant, so let's remove
it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To be consistent when freeing data, let's move the idr_remove() call
from mmc_free_host() into the ->dev_release() callback for the class
device.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As a step in moving slot-gpio functions/structs closer to the MMC core,
let's add a local header file for slot-gpio.
In this initial step we move mmc_gpio_alloc() into the header file,
to make it available for the MMC core. Following patches will show the
utilization of it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We had a mix of using the class device and the parent device while
allocating data through the devm_* managed functions.
Let's be more consistent and always use the parent device.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The slot-gpio uses the devm*_ managed functions. Still it provide APIs
to explicitly free requested CD/WP GPIOs, but these API isn't being
used.
Therefore let's simplify slot-gpio by removing these unused APIs. If it
later turns out we need some of them, we can always consider to restore
the code.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MMC core makes use of the devm_* functions while requesting the
CD/WP GPIOs, let's rely on that.
Cc: Barry Song <baohua@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MMC core makes use of the devm_* functions while requesting the
CD/WP GPIOs, let's rely on that.
Cc: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Instead of just printing an error when mmc_of_parse() fails to request
CD/WP GPIO pins, let's propagate all errors, except for -ENOENT.
Earlier only -EPROBE_DEFER was handled correctly.
As a side effect of this change and by relying on host drivers to
handle the errors during ->probe(), we don't need to free any data in
the error path.
This also means we are actually fixing a bug, since we remove the call
to mmc_gpio_free_cd() which wasn't the correct function to invoke to
handle cleanup. Instead that should have been mmc_gpiod_free_cd().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
At errors, balance sdhci_pltfm_init() with sdhci_pltfm_free(), to make
sure all data is freed properly.
Cc: Srinivas Kandagatla <srinivas.kandagatla@gmail.com>
Cc: Maxime Coquelin <maxime.coquelin@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Since mmc_of_parse() may fail, let's deal with it and thus do proper
error handling.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Since mmc_of_parse() may fail, let's deal with it and thus do proper
error handling.
Cc: Christian Daudt <bcm@fixthebug.org>
Cc: Matt Porter <mporter@linaro.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Since mmc_of_parse() may fail, let's deal with it and thus do proper
error handling.
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Move exynos related definition to header file. And this
also changes some of the registers name to match the standard
naming convention.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
[Alim: updated the commit message]
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Even though 1MB is reserved for descriptor table in IDMAC,
the dw_mmc host driver is allowed to receive only maximum
128KB block length in one request. This is caused by setting
improper max_blk_count. It needs to be e adjusted so that
descriptor table is used fully. It is found that the performance
is improved with the increased the max_blk_count.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Static checkers complain about the inconsistent NULL checking here:
drivers/mmc/host/mxs-mmc.c:680 mxs_mmc_probe()
warn: variable dereferenced before check 'ssp->dmach' (see line 660)
The variable can't actually be NULL so we can remove the check.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Removing a relict from reverse engineering of the Android driver code
in sunxi_mmc_clk_set_rate.
Signed-off-by: David Lanzendörfer <david.lanzendoerfer@o2s.ch>
Reported-by: <lixiang@allwinnertech.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fixing the register name in sunxi_mmc_reset_host since the
SDXC_HARDWARE_RESET bit is actually located within REG_GCTRL and not
REG_CMDR as it was pointed out by Allwinner.
Signed-off-by: David Lanzendörfer <david.lanzendoerfer@o2s.ch>
Reported-by: <lixiang@allwinnertech.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
1) Adding a comment in order to clarify the choice of the locks within
sunxi_mmc_handle_manual_stop
2) As <lixiang@allwinnertech.com> has pointed out the wait_dma variable
was not accessed within the spin lock block in sunxi_mmc_request and so
(even if it should never happend) it would have theoretically been
possible that some other function would access the variable at the same
time as the function. This has been changed now and the function is
using local variables outside the lock and copys the value over during
the lock phase.
Signed-off-by: David Lanzendörfer <david.lanzendoerfer@o2s.ch>
Reported-by: <lixiang@allwinnertech.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The last descriptor might be the first descriptor as well, so use masking to
add the LD (last descriptor) bit and drop the DIC (disable interrupt on
completion) bit rather then hard assignment as hard assignment will override
the FD (first descriptor) bit if there is only 1 descriptor.
Also set the ER (end of ring) bit and clear buf_addr_ptr2 on the last
descriptor, like the android kernel code does.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: David Lanzendörfer <david.lanzendoerfer@o2s.ch>
Reported-by: <lixiang@allwinnertech.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The only function of these 'prepare' and 'complete' is to
disable the 'card detect' irq during suspend.
The commit which added this,
commit a48ce884d5
mmc: omap_hsmmc: Introduce omap_hsmmc_prepare/complete
justified it by the need to avoid the registration of new devices
during suspend.
However mmc_pm_notify will set ->rescan_disable in the 'prepare'
stage and clear it in the 'complete' stage, so no card detection
will actually happen.
Also the interrupt will be disabled before final suspend as part
of common suspend processing.
So this disabling of the interrupt is unnecessary, and interferes
with a transition to using common code for card-detect management.
Cc: Felipe Balbi <balbi@ti.com>
Cc: Venkatraman S <svenkatr@ti.com>
Cc: Chris Ball <cjb@laptop.org>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use the module_pci_driver() macro to make the code simpler
by eliminating module_init and module_exit calls.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The commit 0718e59ae2 ("mmc: sdhci: move FSL ESDHC reset handling quirk into
esdhc code") states that Freescale esdhc is the only controller which needs
the interrupt registers restored after a reset. So it moves
SDHCI_QUIRK_RESTORE_IRQS_AFTER_RESET quirk handling code into the
esdhc-imx driver only. Unfortunately the same controller is used in
other boards which use the of-esdhc driver instead (like powerpc P2020).
Restore interrupts after reset in the sdhci-of-esdhc driver also.
Signed-off-by: Alessio Igor Bogani <alessio.bogani@elettra.eu>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add manual tuning function in CSR atlas7 SoC. It is mainly used
for the UHS-I SD card working SDR50 SDR104 mode.
The tuning principle can be seen in SD spec part1 v3.01 4.2.4.5
(tuning command).
SD host send the cmd19 and set the delay value(0-127).
and the sdcard return 64 bytes data. If the data is same with
the tuning data. The delay value is valid. Execute this commmand
128 times. And calculate the longest window of the valid values.
The value in the middle of this window is the best value.
Signed-off-by: Minda Chen <Minda.Chen@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We're running into cases where our enabling of the SDIO interrupt in
dw_mmc doesn't actually take effect. Specifically, adding patch like
this:
+++ b/drivers/mmc/host/dw_mmc.c
@@ -1076,6 +1076,9 @@ static void dw_mci_enable_sdio_irq(struct mmc_host *mmc, int enb)
mci_writel(host, INTMASK,
(int_mask | SDMMC_INT_SDIO(slot->id)));
+ int_mask = mci_readl(host, INTMASK);
+ if (!(int_mask & SDMMC_INT_SDIO(slot->id)))
+ dev_err(&mmc->class_dev, "failed to enable sdio irq\n");
} else {
...actually triggers the error message. That's because the
dw_mci_enable_sdio_irq() unsafely does a read-modify-write of the
INTMASK register.
We can't just use the standard host->lock since that lock is not irq
safe and mmc_signal_sdio_irq() (called from interrupt context) calls
dw_mci_enable_sdio_irq(). Add a new irq-safe lock to protect INTMASK.
An alternate solution to this is to punt mmc_signal_sdio_irq() to the
tasklet and then protect INTMASK modifications by the standard host
lock. This seemed like a bit more of a high-latency change.
Reported-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In the patch (9623b5b mmc: dw_mmc: Disable low power mode if SDIO
interrupts are used) I added code that disabled the low power mode of
dw_mmc when SDIO interrupts are used. That code worked but always
felt a little hacky because we ended up disabling low power as a side
effect of the first enable_sdio_irq() call. That wouldn't be so bad
except that disabling low power involves a complicated process of
writing to the CMD/CMDARG registers and that extra process makes it
difficult to cleanly the read-modify-write race in
dw_mci_enable_sdio_irq() (see future patch in the series).
Change the code to take advantage of the init_card() callback of the
mmc core to do this right at bootup.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In (3fcb027 ARM: MXC: mxcmmc: work around a bug in the SDHC busy line
handling) the optional init_card() callback was added. According to
the original change it was "for now only called from
mmc_sdio_init_card()".
This callback really ought to be called from the SD and MMC init
functions as well. One current user of this callback
(mxcmci_init_card) will not work as expected if you insert an SDIO
card, then eject it and put a normal SD card in. Specifically the
normal SD card will not get to run with 4-bit data.
I'd like to use the init_card() callback to handle a similar quirk on
dw_mmc when using SDIO Interrupts (the "low power" feature of the card
needs to be disabled), so that will add a second user of the function.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now that we have proper support to use the generic phase API in our clock
driver, switch the MMC driver to use it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: David Lanzendörfer <david.lanzendoerfer@o2s.ch>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Chen-Yu Tsai <wens@csie.org>
Host controllers lacking the required internal vmmc regulator may still
follow the spec with regard to the LSB of SDHCI_POWER_CONTROL. Set the
SDHCI_POWER_ON bit when vmmc is enabled to encourage the controller to
to drive CMD, DAT, SDCLK.
This fixes a regression observed on some Qualcomm and Nvidia boards
caused by 5222161 mmc: sdhci: Improve external VDD regulator support.
Fixes: 52221610dd (mmc: sdhci: Improve external VDD regulator support)
Signed-off-by: Tim Kryger <tim.kryger@gmail.com>
Tested-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Sleep in atomic context happened on Trats2 board after inserting or
removing SD card because mmc_gpio_get_cd() was called under spin lock.
Fix this by moving card detection earlier, before acquiring spin lock.
The mmc_gpio_get_cd() call does not have to be protected by spin lock
because it does not access any sdhci internal data.
The sdhci_do_get_cd() call access host flags (SDHCI_DEVICE_DEAD). After
moving it out side of spin lock it could theoretically race with driver
removal but still there is no actual protection against manual card
eject.
Dmesg after inserting SD card:
[ 41.663414] BUG: sleeping function called from invalid context at drivers/gpio/gpiolib.c:1511
[ 41.670469] in_atomic(): 1, irqs_disabled(): 128, pid: 30, name: kworker/u8:1
[ 41.677580] INFO: lockdep is turned off.
[ 41.681486] irq event stamp: 61972
[ 41.684872] hardirqs last enabled at (61971): [<c0490ee0>] _raw_spin_unlock_irq+0x24/0x5c
[ 41.693118] hardirqs last disabled at (61972): [<c04907ac>] _raw_spin_lock_irq+0x18/0x54
[ 41.701190] softirqs last enabled at (61648): [<c0026fd4>] __do_softirq+0x234/0x2c8
[ 41.708914] softirqs last disabled at (61631): [<c00273a0>] irq_exit+0xd0/0x114
[ 41.716206] Preemption disabled at:[< (null)>] (null)
[ 41.721500]
[ 41.722985] CPU: 3 PID: 30 Comm: kworker/u8:1 Tainted: G W 3.18.0-rc5-next-20141121 #883
[ 41.732111] Workqueue: kmmcd mmc_rescan
[ 41.735945] [<c0014d2c>] (unwind_backtrace) from [<c0011c80>] (show_stack+0x10/0x14)
[ 41.743661] [<c0011c80>] (show_stack) from [<c0489d14>] (dump_stack+0x70/0xbc)
[ 41.750867] [<c0489d14>] (dump_stack) from [<c0228b74>] (gpiod_get_raw_value_cansleep+0x18/0x30)
[ 41.759628] [<c0228b74>] (gpiod_get_raw_value_cansleep) from [<c03646e8>] (mmc_gpio_get_cd+0x38/0x58)
[ 41.768821] [<c03646e8>] (mmc_gpio_get_cd) from [<c036d378>] (sdhci_request+0x50/0x1a4)
[ 41.776808] [<c036d378>] (sdhci_request) from [<c0357934>] (mmc_start_request+0x138/0x268)
[ 41.785051] [<c0357934>] (mmc_start_request) from [<c0357cc8>] (mmc_wait_for_req+0x58/0x1a0)
[ 41.793469] [<c0357cc8>] (mmc_wait_for_req) from [<c0357e68>] (mmc_wait_for_cmd+0x58/0x78)
[ 41.801714] [<c0357e68>] (mmc_wait_for_cmd) from [<c0361c00>] (mmc_io_rw_direct_host+0x98/0x124)
[ 41.810480] [<c0361c00>] (mmc_io_rw_direct_host) from [<c03620f8>] (sdio_reset+0x2c/0x64)
[ 41.818641] [<c03620f8>] (sdio_reset) from [<c035a3d8>] (mmc_rescan+0x254/0x2e4)
[ 41.826028] [<c035a3d8>] (mmc_rescan) from [<c003a0e0>] (process_one_work+0x180/0x3f4)
[ 41.833920] [<c003a0e0>] (process_one_work) from [<c003a3bc>] (worker_thread+0x34/0x4b0)
[ 41.841991] [<c003a3bc>] (worker_thread) from [<c003fed8>] (kthread+0xe4/0x104)
[ 41.849285] [<c003fed8>] (kthread) from [<c000f268>] (ret_from_fork+0x14/0x2c)
[ 42.038276] mmc0: new high speed SDHC card at address 1234
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: 94144a465d ("mmc: sdhci: add get_cd() implementation")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In commit 5491ce3f79 ("mmc: sdhci-pxav3: add support for the Armada
38x SDHCI controller"), the sdhci-pxav3 driver was extended to include
support for the SDHCI controller found in the Armada 38x
processor. This mainly involved adding some MBus window related
configuration.
However, this configuration is currently done too early in ->probe():
it is done before clocks are enabled, while this configuration
involves touching the registers of the controller, which will hang the
SoC if the clock is disabled. It wasn't noticed until now because the
bootloader typically leaves gatable clocks enabled, but in situations
where we have a deferred probe (due to a CD GPIO that cannot be taken,
for example), then the probe will be re-tried later, after a clock
disable has been done in the exit path of the failed probe attempt of
the device. This second probe() will hang the system due to the clock
being disabled.
This can for example be produced on Armada 385 GP, which has a CD GPIO
connected to an I2C PCA9555. If the driver for the PCA9555 is not
compiled into the kernel, then we will have the following sequence of
events:
1. The SDHCI probes
2. It does the MBus configuration (which works, because the clock is
left enabled by the bootloader)
3. It enables the clock
4. It tries to get the CD GPIO, which fails due to the driver being
missing, so -EPROBE_DEFER is returned.
5. Before returning -EPROBE_DEFER, the driver cleans up what was
done, which includes disabling the clock.
6. Later on, the SDHCI probe is tried again.
7. It does the MBus configuration, which hangs because the clock is
no longer enabled.
This commit does the obvious fix of doing the MBus configuration after
the clock has been enabled by the driver.
Fixes: 5491ce3f79 ("mmc: sdhci-pxav3: add support for the Armada 38x SDHCI controller")
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Re-tuning for HS400 mode must be done in HS200
mode. Currently there is no support for that.
That needs to be reflected in the code.
Specifically, if tuning is executed in HS400 mode
then return an error, and do not start the
tuning timer if HS200 tuning is being done prior
to switching to HS400.
Note that periodic re-tuning is not expected
to be needed for HS400 but re-tuning is still
needed after the host controller has lost power.
In the case of suspend/resume that is not necessary
because the card is fully re-initialised. That
just leaves runtime suspend/resume with no support
for HS400 re-tuning.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The tuning timer is always used if the tuning mode
is 1 and there is a tuning count, irrespective of
whether this is the first call, or any subsequent
call. Consequently the logic to start the timer
can be simplified.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
A 'goto' can be used to save duplicating unlocking
and returning.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Re-tuning requires that the maximum data length
is limited to 4MiB. The code currently changes
max_blk_count in an attempt to achieve that.
This is wrong because max_blk_count is a different
limit, but it is also un-necessary because
max_req_size is 512KiB anyway. Consequently, the
changes to max_blk_count are removed and the
comment for max_req_size adjusted accordingly.
The comment is also tweaked to show that the 512KiB
limit is a SDMA limit not an ADMA limit.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_select_bus_width() will try to switch to MMC_BUS_WIDTH_4 even if
MMC_CAP_4_BIT_DATA and MMC_CAP_8_BIT_DATA are not set in host->caps.
Return as soon as possible when those flags are not set
Fixes: 577fb13199 (mmc: rework selection of bus speed mode)
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: <stable@vger.kernel.org> # 3.17
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by
the driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken
into account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should
have used from the start and drop some other unuseful KERN_ERR
messages printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool
(Prarit Bhargava).
- Fix two regressions introduced by recent commits in the OPP
library and clean up some existing minor issues in that code
(Viresh Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout
the tree (or drop it where that can be done) in order to make
it possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki,
Ulf Hansson, Ludovic Desroches). There will be one more
"CONFIG_PM_RUNTIME removal" batch after this one, because some
new uses of it have been introduced during the current merge
window, but that should be sufficient to finally get rid of it.
- Make the ACPI EC driver more robust against race conditions
related to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to
disable GPEs that it has not enabled which confuses ACPICA
and makes it report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver
to make it possible to override the blacklisting of some
systems in that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS
entry for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces
witn names that reflect the IDs of the ACPI device objects
they are associated with, except for "generic" ACPI fans
(PNP ID "PNP0C0B"). That's necessary for user space thermal
management tools to be able to connect the fans with the
parts of the system they are supposed to be cooling properly.
From Srinivas Pandruvada.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=5fo2
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management updates from Rafael Wysocki:
"These are regression fixes (leds-gpio, ACPI backlight driver,
operating performance points library, ACPI device enumeration
messages, cpupower tool), other bug fixes (ACPI EC driver, ACPI device
PM), some cleanups in the operating performance points (OPP)
framework, continuation of CONFIG_PM_RUNTIME elimination, a couple of
minor intel_pstate driver changes, a new MAINTAINERS entry for it and
an ACPI fan driver change needed for better support of thermal
management in user space.
Specifics:
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by the
driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken into
account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should have
used from the start and drop some other unuseful KERN_ERR messages
printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool (Prarit
Bhargava).
- Fix two regressions introduced by recent commits in the OPP library
and clean up some existing minor issues in that code (Viresh
Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout the
tree (or drop it where that can be done) in order to make it
possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki, Ulf
Hansson, Ludovic Desroches).
There will be one more "CONFIG_PM_RUNTIME removal" batch after this
one, because some new uses of it have been introduced during the
current merge window, but that should be sufficient to finally get
rid of it.
- Make the ACPI EC driver more robust against race conditions related
to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to disable
GPEs that it has not enabled which confuses ACPICA and makes it
report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver to
make it possible to override the blacklisting of some systems in
that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS entry
for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces witn
names that reflect the IDs of the ACPI device objects they are
associated with, except for "generic" ACPI fans (PNP ID "PNP0C0B").
That's necessary for user space thermal management tools to be able
to connect the fans with the parts of the system they are supposed
to be cooling properly. From Srinivas Pandruvada"
* tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
MAINTAINERS: add entry for intel_pstate
ACPI / video: update the skip case for acpi_video_device_in_dod()
power / PM: Eliminate CONFIG_PM_RUNTIME
NFC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
SCSI / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / EC: Fix unexpected ec_remove_handlers() invocations
Revert "tools: cpupower: fix return checks for sysfs_get_idlestate_count()"
tracing / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
x86 / PM: Replace CONFIG_PM_RUNTIME in io_apic.c
PM: Remove the SET_PM_RUNTIME_PM_OPS() macro
mmc: atmel-mci: use SET_RUNTIME_PM_OPS() macro
PM / Kconfig: Replace PM_RUNTIME with PM in dependencies
ARM / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
sound / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
phy / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
video / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tty / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
spi: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / PM: Do not disable wakeup GPEs that have not been enabled
ACPI / utils: Drop error messages from acpi_evaluate_reference()
...
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
The currently used SET_PM_RUNTIME_PM_OPS() macro is defined to the
SET_RUNTIME_PM_OPS() macro. Convert to the later, since that's the
proper one to use.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come
from as long as the platform firmware (either DT or ACPI) makes
them available. It covers both devices and "bare" device node
objects without struct device representation as that turns out to
be necessary in some cases. This has been in the works for quite
a few months (and development cycles) and has been approved by
all of the relevant maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO information
in their ACPI tables, but don't assign names to GPIO lines (in which
case the driver needs to do that on the basis of what it knows about
the device in question). That also has been approved by the GPIO
core maintainers and the rfkill driver is now going to use it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by
the processor in which case it will be enabled by default. However,
it can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller).
The support added this time is sufficient to make the ACPI battery
driver work on Asus T100A, but it is general enough to be able to
cover some other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver
for Intel platforms should be able to handle power management of
the DMA engine correctly, the cpufreq-dt driver should interact
with the thermal subsystem in a better way and the ACPI backlight
driver should handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions
in the ACPICA's interrupt handling code which might lead to some
random and strange looking failures on some systems.
In the cleanups department the most visible part is the series
of commits targeted at getting rid of the CONFIG_PM_RUNTIME
configuration option. That was triggered by a discussion
regarding the generic power domains code during which we realized
that trying to support certain combinations of PM config options
was painful and not really worth it, because nobody would use them
in production anyway. For this reason, we decided to make
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and that lead to the
conclusion that the latter became redundant and CONFIG_PM could
be used instead of it. The material here makes that replacement
in a major part of the tree, but there will be at least one more
batch of that in the second part of the merge window.
Specifics:
- Support for retrieving device properties information from ACPI
_DSD device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that.
As stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers
are now going to use this new interface and the GPIO subsystem
is additionally modified to allow device drivers to assign names
to GPIO resources returned by ACPI _CRS objects (in case _DSD is
not present or does not provide the expected data). The changes
in this set are mostly from Mika Westerberg, Rafael J Wysocki,
Aaron Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions
used by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management
(Aaron Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects
and deferred probing support for the ACPI battery driver based
on the _DEP information to make that driver work on Asus T100A
(Lan Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling
code and in the ACPI code related to system suspend and resume
(Lv Zheng and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had
been allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in
that code with synchronize_rcu_expedited() which makes the issue
go away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly.
The problem is that the DMA engine doesn't have ACPI PM support
of its own and it simply is turned off when the last LPSS device
having ACPI PM support goes into D3cold. To work around that,
the PM domain used by the ACPI LPSS driver is redesigned so at
least one device with ACPI PM support will be on as long as the
DMA engine is in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and
Ashwin Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver
fixes and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at
probe time (Ulf Hansson).
- Preliminary support for controlling device clocks from the
generic power domains core code and modifications of the
ARM/shmobile platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power
domains core code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control
code in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and
a new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu,
James Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to
allow OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and
Markus Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=5dox
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come from
as long as the platform firmware (either DT or ACPI) makes them
available. It covers both devices and "bare" device node objects
without struct device representation as that turns out to be necessary
in some cases. This has been in the works for quite a few months (and
development cycles) and has been approved by all of the relevant
maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO
information in their ACPI tables, but don't assign names to GPIO lines
(in which case the driver needs to do that on the basis of what it
knows about the device in question). That also has been approved by
the GPIO core maintainers and the rfkill driver is now going to use
it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by the
processor in which case it will be enabled by default. However, it
can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller). The
support added this time is sufficient to make the ACPI battery driver
work on Asus T100A, but it is general enough to be able to cover some
other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver for
Intel platforms should be able to handle power management of the DMA
engine correctly, the cpufreq-dt driver should interact with the
thermal subsystem in a better way and the ACPI backlight driver should
handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions in the
ACPICA's interrupt handling code which might lead to some random and
strange looking failures on some systems.
In the cleanups department the most visible part is the series of
commits targeted at getting rid of the CONFIG_PM_RUNTIME configuration
option. That was triggered by a discussion regarding the generic
power domains code during which we realized that trying to support
certain combinations of PM config options was painful and not really
worth it, because nobody would use them in production anyway. For
this reason, we decided to make CONFIG_PM_SLEEP select
CONFIG_PM_RUNTIME and that lead to the conclusion that the latter
became redundant and CONFIG_PM could be used instead of it. The
material here makes that replacement in a major part of the tree, but
there will be at least one more batch of that in the second part of
the merge window.
Specifics:
- Support for retrieving device properties information from ACPI _DSD
device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that. As
stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers are
now going to use this new interface and the GPIO subsystem is
additionally modified to allow device drivers to assign names to
GPIO resources returned by ACPI _CRS objects (in case _DSD is not
present or does not provide the expected data). The changes in
this set are mostly from Mika Westerberg, Rafael J Wysocki, Aaron
Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions used
by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management (Aaron
Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects and
deferred probing support for the ACPI battery driver based on the
_DEP information to make that driver work on Asus T100A (Lan
Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling code
and in the ACPI code related to system suspend and resume (Lv Zheng
and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had been
allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in that
code with synchronize_rcu_expedited() which makes the issue go
away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly. The
problem is that the DMA engine doesn't have ACPI PM support of its
own and it simply is turned off when the last LPSS device having
ACPI PM support goes into D3cold. To work around that, the PM
domain used by the ACPI LPSS driver is redesigned so at least one
device with ACPI PM support will be on as long as the DMA engine is
in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and Ashwin
Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver fixes
and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at probe
time (Ulf Hansson).
- Preliminary support for controlling device clocks from the generic
power domains core code and modifications of the ARM/shmobile
platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power domains core
code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control code
in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and a
new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu, James
Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to allow
OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and Markus
Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava)"
* tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (120 commits)
i2c-omap / PM: Drop CONFIG_PM_RUNTIME from i2c-omap.c
dmaengine / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tools: cpupower: fix return checks for sysfs_get_idlestate_count()
drivers: sh / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
e1000e / igb / PM: Eliminate CONFIG_PM_RUNTIME
MMC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
MFD / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
misc / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
media / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
input / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
leds: leds-gpio: Fix multiple instances registration without 'label' property
iio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hsi / OMAP / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
i2c-hid / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
drm / exynos / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
gpio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hwrandom / exynos / PM: Use CONFIG_PM in #ifdef
block / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
USB / PM: Drop CONFIG_PM_RUNTIME from the USB core
PM: Merge the SET*_RUNTIME_PM_OPS() macros
...
Instead of having a local hack taking care of sending the tuning
command and as well to verify the response pattern, let's convert to
the common mmc_send_tuning() API instead.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Georgi Djakov <gdjakov@mm-sol.com>
Acked-by: Georgi Djakov <gdjakov@mm-sol.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Instead of having a local function taking care of sending the tuning
command, let's use the common mmc_send_tuning() API provided by the mmc
core. In this way the request will be handled as any other request by
sdhci core.
As an effect of this change, the pm_runtime_get_sync() call at
esdhc_prepare_tuning() isn't needed any more.
This patch will also introduce another change in behavior, since before
the response pattern to the tuning command wasn't verified by
sdhci-esdhc-imx. The mmc_send_tuning() does that.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Dong Aisheng <b29396@freescale.com>
To be able to use mmc_send_tuning() prior the struct mmc_card has been
allocated, let's convert it to take the struct mmc_host* as parameter
instead.
Suggested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Dong Aisheng <b29396@freescale.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Allocation of previous bounce buffer in mmc_init_queue when the current
bounce buffer allocation fails was leading to a crash later in
__blk_segment_map_sg. Error handling is improved by allocating previous
bounce buffer only if the current bounce buffer allocation succeeds.
Signed-off-by: Bhuvanesh Surachari <bhuvanesh_surachari@mentor.com>
Signed-off-by: Harish Jenny K N <harish_kandiga@mentor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.
Replace CONFIG_PM_RUNTIME with CONFIG_PM everywhere under
drivers/mmc/.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
The SET_PM_RUNTIME_PM_OPS() and SET_RUNTIME_PM_OPS() macros are
identical except that one of them is not empty for CONFIG_PM set,
while the other one is not empty for CONFIG_PM_RUNTIME set,
respectively.
However, after commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if
PM_SLEEP is selected) PM_RUNTIME is always set if PM is set, so one
of these macros is now redundant.
For this reason, replace SET_PM_RUNTIME_PM_OPS() with
SET_RUNTIME_PM_OPS() everywhere and redefine the SET_PM_RUNTIME_PM_OPS
symbol as SET_RUNTIME_PM_OPS in case new code is starting to use the
macro being removed here.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Intel host controllers are capable of doing the bus
width test and of waiting while busy, so add the
capability flags.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
BYT host controllers are capable of doing the bus
width test and of waiting while busy, so add the
capability flags.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC actually causes
standard-compliant behaviour by causing the flagging
of the last DMA transfer descriptor as the end
instead of there being an additional nop descriptor
which is flagged as the end. Consequently, it is
better to have the quirk.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC actually causes
standard-compliant behaviour by causing the flagging
of the last DMA transfer descriptor as the end
instead of there being an additional nop descriptor
which is flagged as the end. Consequently, it is
better to have the quirk. Add it for BYT.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
No more use late initcall to manage probing order. Use probe deferring
if needed.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Using __init/__exit attributes can cause several breakages so remove
them.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
All devices with a DMA controller are DT compliant and legacy support
has been removed. For those reasons, some DMA stuff is useless.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The commit, mmc: omap: clarify DDR timing mode between SD-UHS and eMMC,
switched omap_hsmmc to support MMC DDR mode instead of UHS DDR50 mode.
Add UHS DDR50 mode again and this time let's also keep the MMC DDR mode.
Fixes: 5438ad95a5 (mmc: omap: clarify DDR timing mode between SD-UHS and eMMC)
Reported-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According to the SD card spec, Add a manual tuning command function
for SDR104/HS200.
Sending command 19 or command 21 to read data and compare with the
tunning block pattern.
This patch will help to decrease some platform private codes in SDHCI
platform_execute_tuning() callbacks.
Signed-off-by: Minda Chen <Minda.Chen@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Voltage Switch Procedure
This patch is to fix an issue found on mb86s7x platforms.
[symptom]
There are some UHS-1 SD memory cards sometimes cannot be detected correctly,
e.g., Transcend 600x SDXC 64GB UHS-1 memory card.
During Signal Voltage Switch Procedure, failure to switch is indicated
by the card holding DAT[3:0] low.
[analysis]
According to SD Host Controller Simplified Specification Version 3.00
chapter 3.6.1, the Signal Voltage Switch Procedure should be:
(1) Check S18A; (2) Issue CMD11; (3) Check CMD 11 response;
(4) Stop providing SD clock; (5) Check DAT[3:0] should be 0000b;
(6) Set 1.8V Signal Enable; (7) Wait 5ms; (8) Check 1.8V Signal Enable;
(9) Provide SD Clock; (10) Wait 1ms; (11) Check DAT[3:0] should be 1111b;
(12) error handling
With CONFIG_MMC_CLKGATE=y, sometimes there is one more gating/un-gating
SD clock between (2) and (3). In this case, some UHS-1 SD cards will hold
DAT[3:0] 0000b at (11) and thus fails Signal Voltage Switch Procedure.
[solution]
By mmc_host_clk_hold() before CMD11, the additional gating/un-gating
SD clock between (2) and (3) can be prevented and thus no failure at (11).
It has been verified with many UHS-1 SD cards on mb86s7x platforms and
works correctly.
Signed-off-by: Vincent Yang <Vincent.Yang@tw.fujitsu.com>
Reviewed-by: Johan Rudholm <jrudholm@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
clk_prepare_enable() may fail and in this case we should propagate the error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If platform_get_irq() fails, it is better to propagate the real error value
instead of a 'fake' one.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
devm_ioremap_resource() already checks if 'iores' is NULL or not, so we can
skip this manual check.
While at it, move platform_get_resource() closer to devm_ioremap_resource() for
better readability.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support for the DW MMC host found on the Imagination Pistachio SoC.
Like the DW MMC hosts found on SOCFPGA and Rockchip SoCs, the DW MMC
host on Pistachio requires the use of SDMMC_CMD_USE_HOLD_REG.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
By using SIMPLE_DEV_PM_OPS we can make the code smaller and cleaner.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Instead of registering the irq name with the driver's name, it's better to pass
the device name so that we have a more explicit indication as to what mmc
instance the irq is related:
$ cat /proc/interrupts
CPU0
...
26: 6 - 96 80010000.ssp
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit f1d2736c81 (mmc: dw_mmc: control card read threshold) added
dw_mci_ctrl_rd_thld() with an unconditional write to the CDTHRCTL
register at offset 0x100. However before version 240a, the FIFO region
started at 0x100, so the write messes with the FIFO and completely
breaks the driver.
If the version id < 240A, return early from dw_mci_ctl_rd_thld() so as
not to hit this problem.
Fixes: f1d2736c81 (mmc: dw_mmc: control card read threshold)
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: <stable@vger.kernel.org> # v3.13+
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We check for NULL pointers after dereferencing so it's too late. Oddly
enough, Smatch misses this code but complains about the caller passing
NULL pointers to this function:
drivers/mmc/host/toshsd.c:389 toshsd_irq()
error: we previously assumed 'host->cmd' could be null (see line 349)
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
All boards with a dma controller have DT support so using
dma_request_slave_channel_compat is no more needed.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The bit of sdio interrupt is 16 in designware implementation,
but it is 24 on Rockchip SoCs.This patch add sdio_id0 for the
number of slot0 in the SDIO interrupt registers.
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In order to use the mvsdio driver for sdio, it has been necessary to
use a module parameter to disable DMA so to force PIO is used. It is
then possible to use wireless LAN devices like mwifiex found on
topkick and mirabox. However, accessing an MMC SD card does work with
DMA.
Investigation has shown that MMC block device accesses are always
aligned to 64 byte boundaries, where as transfers from mwifiex are
rarely more than word aligned. It has also been determined that card
to host transfers work with DMA for SDIO devices, but host to card
transfers with DMA have problems.
This patch extends the current checks for buffers which are not word
aligned or multiple of words. All host to card transfers which are not
64 byte aligned are now also performed via PIO. This should not affect
the performance of SD cards, but allow sdio devices to work out of the
box, and they are likely to be more efficient since DMA will be used
for card to host transfers.
Tested on mirabox for wifi via mwifiex
Tested on 370 RD for file systems on an SD card.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently the driver imposes a limit of 256 total minor numbers,
apparently based on the historic Unix/Linux limit. This is quite
restrictive, particularly if we raise the maximum number of
partitions per card to 256 to match sd.
In order to make the full minor number space available we would
have to replace the static dev_use and name_use arrays with struct
ida. But we can at least allow use of 256 cards rather than just
256 minors, with only a small change.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There are upcoming ARM64 SoCs with dw_mmc host controller.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As we are restoring power to a known card, it makes sense to use
the 'ocr' value known for the card rather than the generic one
for the host interface.
This matches the use of card->ocr passed to mmc_power_up in
mmc_sdio_runtime_resume (just before mmc_sdio_power_restore is
called), and the value passed to mmc_sdio_init_card() a little
later in mmc_sdio_power_restore().
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch resurrects an old never-finished driver for Toshiba PCI SD
controllers found in some older Toshiba laptops (such as Portege R100):
02:0d.0 System peripheral [0880]: Toshiba America Info Systems SD TypA Controller [1179:0805] (rev 05)
The code is fixed, cleaned up and successfully tested with SD, SDHC, SDXC and
MMC cards on Portege R100. (MMC cards don't even work in Windows!)
SDIO probably does not work (don't have any SDIO card).
The hardware is slow (around 2 MB/s - same in Windows) because it does not
support bus mastering (busmaster enable bit cannot be set in PCI control reg).
Also the card clock is limited to 16MHz (33MHz PCI clock divided by 2).
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The Exynos7 has a DWMMC controller (v2.70a) which is different from
prior versions. This patch adds new compatible strings for exynos7.
This patch also fixes the CLKSEL register offset on exynos7.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Tested-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_do_hw_reset(), mmc_power_up() and mmc_power_off() all set similar
initial values for bus_mode, bus_width, chip_select and timing. Let's
make this handling simpler and more consistent by sticking them
together in a common function. This will introduce small changes in
behavior in the following places:
mmc_power_off():
For SPI hosts, explicitly set bus_mode = MMC_BUSMODE_PUSHPULL and
chip_select = MMC_CS_HIGH, before we left them as they were.
For non-SPI hosts, set bus_mode = MMC_BUSMODE_PUSHPULL instead of
MMC_BUSMODE_OPENDRAIN as before.
These two changes should not be a problem since the device will be
powered off anyway.
mmc_do_hw_reset():
Always set bus_mode = MMC_BUSMODE_PUSHPULL, as required by SD/SDIO
cards. MMC cards require MMC_BUSMODE_OPENDRAIN, but this is taken
care of by mmc_init_card() and mmc_attach_mmc().
Signed-off-by: Johan Rudholm <johanru@axis.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
omap_hsmmc only supports one slot. So slot id is always zero, and
slot id was never used in the callbacks anyway
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
These callbacks are set during driver probe and not from the platform
init, -- evtl. they had been for oamp 1/2 -- for omap3 they are local
functions of the driver. These indirection could be dropped
altogether in favor of regular function calls TODO
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
this is needed when installing callbacks in the host struct and not
in the platform data, e.g. cover detect irq should be stored in
omap_hsmmc_host and not platform data
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
omap_hsmmc supports only one slot per controller, see OMAP_MMC_MAX_SLOTS.
This unnecessary indirection leads to confusion in the omap_hsmmc driver.
For example the card_detect callback is not installed by platform code
but from the driver probe function. So it should be a field of
omap_hsmmc_host. But since it is declared under the platform slot while
the drivers struct omap_hsmmc_host has no slot abstraction, this looks
like a bug, especially when not familiar that this driver only supports
1 slot anyway.
Either we should add a slot abstraction to omap_hsmmc_host or remove
it from the platform data struct. Removed since slot multiplexing is
an un-implemented feature
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
these callbacks are not set, probably legacy omap 1/2 features
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- omap mmc driver supports multiplexing, omap_mmc_hs doesn't
this leads to one of the major confusions in the omap_hsmmc driver
- platform data should be read-only for the driver
most callbacks are not set by the omap3 platform init code while still
required. So they are set from the driver probe function, which is against
the paradigm that platform-data should not be modified by the driver
typical examples are card_detect, read_only callbacks
un-bundling by searching for driver name \"omap_hsmmc in the
arch/arm folder. omap_hsmmc_platform_data is not initialized directly,
but from omap2_hsmmc_info, which is defined in a separate header file
not touched by this patch
hwmod includes platform headers to declare features of the platform. All
the declared features are prefixed OMAP_HSMMC. There is no need to
include platform header from hwmod other except for feature defines
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Amend the atmel mci pin controller to optionally take a pin control
handle and set the state of the pins to:
- "default" on boot, resume and before performing an transfer.
- "sleep" on suspend().
This should make it possible to optimize energy usage for the pins
both for the suspend/resume cycle.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
MMC core already has support for HS400. Add HS400
support to SDHCI driver. The SDHC Standard specification
does not define HS400 so consequently HS400 support is
non-standard. However HS400 is not selected without
the host controller setting the corresponding capability
flags so host controllers not yet supporting HS400
will not be affected. To support that, a quirk
SDHCI_QUIRK2_CAPS_BIT63_FOR_HS400 is introduced to
enable the use of capabilities register reserved bit-63
to indicate HS400 support.
Because HS400 is non-standard for SDHCI, it is possible
that different vendors will do things in different ways.
However HS200 support faced the same issue but currently
there is only one solution. As such, no attempt has
been made to provide for alternate HS400 solutions except
for SDHCI_QUIRK2_CAPS_BIT63_FOR_HS400.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
1.2V HS200 mode capability is cleared if there is not a voltage
regulator that supports 1.2V. Do the same for 1.2V HS400 mode.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
supply.vqmmc is used with the IS_ERR macro which means
the value must be valid or an error code. NULL is
neither, so replace with ERR_PTR(-EINVAL).
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Synopsys DW_MMC IP core supports Internal DMA Controller with 64-bit address mode from IP version 2.70a onwards.
Updated the driver to support IDMAC 64-bit addressing mode.
Signed-off-by: Prabu Thangamuthu <prabu.t@synopsys.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
AMD SD controller supports the SDR104 mode, but caps2 can not
be promoted to support hs200 for eMMC.
Signed-off-by: Vincent Wan <vincent.wan@amd.com>
Signed-off-by: Wan Zongshun <mcuos.com@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch is to enable the quirk for AMD sdhci requiring transfer
mode register need to be cleared for commands without data
Signed-off-by: Vincent Wan <vincent.wan@amd.com>
Signed-off-by: Wan Zongshun <mcuos.com@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDHC controller in AMD chipsets require SDHC transfer mode
register to be cleared for commands without data. The issue was
uncovered during testing eMMC cards on KB/ML based platforms
Signed-off-by: Vincent Wan <vincent.wan@amd.com>
Signed-off-by: Wan Zongshun <mcuos.com@gmail.com>
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Tested-by: Vikram B <vikram.b@amd.com>
Tested-by: Raghavendra Swamy <raghavendra.swamy@amd.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It is possible that we may fail to set the clock rate, if we do so then
log the failure and don't bother reprogramming the IP.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The "Badly aligned" tests, test reading/writing with alignments
of 1,2 and 3. SDHCI now has 64-bit ADMA which has 8-byte
alignment, so extend the tests to test up to 7.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Set a 64-bit DMA mask when using 64-bit DMA.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Set the DMA mask during the first call to ->enable_dma() to
make use of the SDHCI_USE_64_BIT_DMA flag.
This patch is dependent on
commit 8a2f38ddfe ("ACPI / platform: provide default DMA mask")
which provides the dev->dma_mask pointer without
which dma_set_mask_and_coherent() will always fail.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add 64-bit ADMA support including:
- add 64-bit ADMA descriptor
- add SDHCI_USE_64_BIT_DMA flag
- set upper 32-bits of DMA addresses
- ability to select 64-bit ADMA
- ability to use 64-bit ADMA sizes and alignment
- display "ADMA 64-bit" when host is added
It is assumed that a 64-bit capable device has set a 64-bit DMA mask
and *must* do 64-bit DMA. A driver has the opportunity to change
that during the first call to ->enable_dma(). Similarly
SDHCI_QUIRK2_BROKEN_64_BIT_DMA must be left to the drivers to
implement.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Define the ADMA descriptor structure instead of
using manual offsets and casts.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Define all the ADMA constants instead of having numbers
scattered throughout the code.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Define the maximum number of segments instead of
having the constant 128 appearing in the code in
various places.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation for 64-bit ADMA, parameterize ADMA sizes
and alignment. 64-bit ADMA has a larger descriptor
because it contains a 64-bit address instead of a 32-bit
address. Also data must be 8-byte aligned instead
of 4-byte aligned. Consequently, sdhci_host members
are added for descriptor, table, and buffer sizes
and alignment.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It is kernel-style to use 'void *' for anonymous data.
This is being applied to the ADMA bounce buffer which
contains unaligned bytes, and to the ADMA descriptor
table which will contain 32-bit ADMA descriptors
or 64-bit ADMA descriptors when support is added.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation for 64-bit ADMA, separate out code
that touches the ADMA descriptor by adding
sdhci_adma_mark_end().
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation for 64-bit ADMA, rename adma_desc to
adma_table. That is because members will be added
for descriptor size and table size, so using adma_desc
(which is the table) is confusing.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Rename sdhci_set_adma_desc to sdhci_adma_write_desc and
sdhci_show_adma_error to sdhci_adma_show_error so that
all ADMA functions start with sdhci_adma_.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The intent of the warning is to warn if the ADMA table
overflows. However there can be one more 'end' entry
so the condition should be adjusted accordingly.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Bytes are being copied from/to a single page. The intent
of the warning is to warn if the page boundary is crossed.
There are two problems. First, PAGE_MASK is mistaken for
(PAGE_SIZE - 1). Secondly, instead of using the number
of bytes to copy, the warning is using the maximum that
that value could be. Fix both.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The ADMA2 descriptor table size was being calculated incorrectly
Fix it.
Note that it has been wrong for a long time and likely has not
caused any problems because of a combination of 1) not needing
alignment descriptors for block operations 2) more memory being
allocated than was requested 3) the use of
SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC which does not use an extra
descriptor for the end marker.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support for non-removable slots which have no card detection GPIO
and which should not be polled for a card change.
Signed-off-by: Timo Kokkonen <timo.kokkonen@offcode.fi>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Besides the I/O clock, some PXAv3 SDHCI IP also requires a core clock to
be enabled. Add an optional core clock to the corresponding driver.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
With support for more than one clock, we'll need to distinguish between
the clock by name. Change clock probing to first try to get "io" clock
before falling back to unnamed clock.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As we are using references to the I/O clock throughout the driver,
move it to the private data. Also, in preparation for core clock,
rename it to clk_io.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci_add_host and sdhci_platfm_init already report failure,
so don't emit error messages when a failure occurs. This prevents
occurences of "deferred" messages when required power supplies
are not ready for operation yet.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Due to previous patches, all callers of mmc_send_cxd_data() now
allocates their buffers from the heap. This enables us to simplify
mmc_send_cxd_data() by removing the support of handling buffers, which
are allocated from the stack.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Previous patches has replaced the calls to mmc_send_ext_csd() into
mmc_get_ext_csd(), thus mmc_send_ext_csd() has become redundant. Let's
remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Callers of mmc_send_ext_csd() will be able to decrease code duplication
by using mmc_get_ext_csd() instead. Let's make it available.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The callers of mmc_get_ext_csd() need the flexibility to handle errors
themselves, because they behave differently.
Let's clean up mmc_get_ext_csd() with its friends and adopt the error
handling as stated above.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As a step in cleaning up code around reading/decoding EXT_CSD, convert
the current mmc_read_ext_csd(), to handle both fetching the EXT_CSD
and decoding its data.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The helper function mmc_can_ext_csd() will return a positive value if
the card supports the EXT_CSD register. Start using it at relavant
places in the mmc core.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If the MMC spec version is < CSD_SPEC_VER_4, there aren't support for
the EXT_CSD register. Since max_dtr is fetched from there, it will
default to zero, which thus isn't needed to verify.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The validation of the buswidth and the MMC spec version in
__mmc_select_powerclass() is redundant, let's remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_send_ext_csd() is an exported function used by both the mmc core
and the mmc block layer. Let's remove the local duplicated definition
in the mmc core.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The dw_mmc driver had a bunch of code that ran whenever a card was
ejected and inserted. However, this code was old and crufty and
should be removed. Some evidence that it's really not needed:
1. Is is supposed to be legal to use 'cd-gpio' on dw_mmc instead of
using the built-in card detect mechanism. The 'cd-gpio' code
doesn't run any of the crufty old code but yet still works.
2. While looking at this, I realized that my old change (369ac86 mmc:
dw_mmc: don't queue up a card detect at slot startup) actually
castrated the old code a little bit already and nobody noticed.
Specifically "last_detect_state" was left as 0 at bootup. That
means that on the first card removal none of the crufty code ran.
3. I can run "while true; do dd if=/dev/mmcblk1 of=/dev/null; done"
while ejecting and inserting an SD Card and the world doesn't
explode.
If some of the crufty old code is actually needed, we should justify
it and also put it in some place where it will be run even with
"cd-gpio".
Note that in my case I'm using the "cd-gpio" mechanism but for various
reasons the hardware triggers a dw_mmc "card detect" at bootup. That
was actually causing a real bug. The card detect workqueue was
running while the system was trying to enumerate the card. The
"present != slot->last_detect_state" triggered and we were doing all
kinds of crazy stuff and messing up enumeration. The new mechanism of
just asking the core to check the card is much safer and then the
bogus interrupt doesn't hurt.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: alim.akhtar <alim.akhtar@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Presumably ->slotno is normally fairly small and the shift doesn't wrap
but static checkers will complain about it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
"ret" is a signed int, so use "%d" in format strings instead of "%u".
This prevents cryptic codes in error messages like this:
sdhci-arasan e0101000.sdhci: platform register failed (4294966779)
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Move the mach header that can come either from arm/mach-at91 or avr32 to
platform_data to be able to switch the AT91 platforms to multiplatform.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
[Ulf: Fixed compile error]
For eMMC 5.0 compliant device, firmware version is stored in ext_csd.
Report firmware as a 64bit hexa decimal. Vendor can use hexa or ascii
string to report firmware version.
Also add FFU related EXT_CSD register and note if the device is FFU capable.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The "set_ios" function is called with a clock of 0 when the clock is
turning off. There's no reason to go through all the extra Rockchip
logic (whose goal is to make sure DIV is 0 or 1) in that case. The
Rockchip logic happened to work because the CCF will pick the lowest
possible rate when you ask it for a clock of 0, but it's silly to go
through all the remuxing and adjusting for no reason.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In (28f92b5 mmc: core: Try other signal levels during power up) we can
see that there are times when it's valid to try several signal
voltages. Don't print an ugly error in the logs when that happens.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We've already got a reset of DMA after it's done. Add one before we
start DMA too. This fixes a data corruption on Rockchip SoCs which
will get bad data when doing a DMA transfer after doing a PIO transfer.
We tested this on an Exynos 5800 with HS200 and didn't notice any
difference in sequential read throughput.
Signed-off-by: Sonny Rao <sonnyrao@chromium.org>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In most of the cases mmc_get|set_drvdata() didn't simplify code, which
should be the primary reason for such macros.
Let's remove them and convert to the common device_driver macros,
dev_set|get_drvdata() instead.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The msm_sdcc host shall not use mmc core specific macros to handle its
driver data. Instead, convert to use the platform device driver macros.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The struct mmc_driver adds an extra layer on top of the struct
device_driver. That would be fine, if there were a good reason, but
that's not the case.
Let's simplify code by converting to the common struct device_driver
instead and thus also removing superfluous overhead.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Instead of having specific mmc system PM callbacks for the mmc driver,
let's convert to use the common ones.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
NULL-checking a struct clk it not only wrong but also not required as
for PXAv3 driver the corresponding clock is mandatory. Remove the
checks from sdhci_pxav3_runtime_{suspend,resume}.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
clk_enable from struct sdhci_pxa is unused, remove it from the private
driver data.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
struct sdhci_pxa is only used in sdhci_pxa driver itself, so move it
there.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
commit bb8175a8aa
("mmc: sdhci: clarify DDR timing mode between SD-UHS and eMMC")
added MMC_DDR52 as eMMC's DDR mode to be distinguished from SD-UHS.
While the differentation may be useful, pxav3 SDHCI controller lacks
a corresponding check in its custom .set_uhs_signaling callback for
MMC_DDR52. This patch adds a new switch case for MMC_TIMING_MMC_DDR52
to MMC_TIMING_UHS_DDR50 case.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
struct sdhci_pxa is private data of PXA SDHCI driver, but not used in
sdhci-pxav2 at all. Drop unused references to struct sdhci_pxa.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
While starting the bkops the previously prepared request should be canceled
and restarted after the bkops. As the prepared resource might already
setup the dma channels and ready to be started. Now with the arrival of bkops
request this prepared request can be serviced ONLY after the bkops. So
holding on to the prepared request in the host driver is confusing at
this point in time, so it makes sense to cleanup such dangling requests and
reissue this request once bkops is done.
Canceling the prepared request would give opportunity to the host drivers
to perform cleanup on the prepared request.
Without this patch host drivers like mmci gets confused when a blocking
request like send_ext_csd(CMD8) is issued while there is already a prepared
request. With the help of this patch, the driver can better manage such
blocking requests and cleanup the prepared requests which are not started yet.
Without this patch I hit below crash on Qualcomm APQ8064 based IFC6410 board
with mmci host driver.
mmci-pl18x 12400000.sdcc: error during DMA transfer!
Unable to handle kernel paging request at virtual address 40000000
pgd = c0204000
[40000000] *pgd=00000000
Internal error: Oops: 805 [#1] SMP ARM
Modules linked in: ipv6 ath6kl_sdio ath6kl_core
CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W 3.17.0-rc7-linaro-multi-v7 #1
task: c0c9d7e0 ti: c0c92000 task.ti: c0c92000
PC is at v7_dma_inv_range+0x34/0x4c
LR is at __dma_page_dev_to_cpu+0x80/0x100
pc : [<c021efc0>] lr : [<c021af18>] psr: 400f0193
sp : c0c93e20 ip : c0c9a478 fp : c08ea538
r10: c0c9f548 r9 : 00000002 r8 : e97d9000
r7 : 00000200 r6 : c0c9d504 r5 : c0db0880 r4 : 00000000
r3 : 0000003f r2 : 00000040 r1 : 40000200 r0 : 40000000
Flags: nZcv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel
Control: 10c5787d Table: a9ef406a DAC: 00000015
Process swapper/0 (pid: 0, stack limit = 0xc0c92250)
Stack: (0xc0c93e20 to 0xc0c94000)
3e20: c021f058 e9a17178 e9a171bc e99dfd6c 00000001 00000001 e995de10 00000002
3e40: 00000000 c021b574 00000000 c04bc4a4 00000000 e9b49ac0 c0ce6e6c e99dfda4
3e60: 00000088 e9810780 c0d8291c c072ea58 00000000 c072d3fc 00000000 c072f534
3e80: 00000000 e9b49ac0 00000100 c0c9a444 00000088 c072f6b4 c072f5d4 e9d40080
3ea0: e98107dc 00000000 00000000 c0280a60 00000000 7d55bf61 e9810780 e98107dc
3ec0: 00000000 f0002000 c0d460e8 c0d460e8 c0c92000 c0280b60 e9810780 c0ce7190
3ee0: 00000000 c028369c c02835f4 00000088 00000088 c0280278 c0c8ec70 c020f080
3f00: f000200c c0c9a958 c0c93f28 c02088e4 c04bd630 c04bd5bc 200f0013 ffffffff
3f20: c0c93f5c c0212800 00000001 a987c000 c0c93f3c c04bd574 00000000 0000015b
3f40: ea7a0e40 00000000 c0d460e8 c0d460e8 c0c92000 c08ea538 29b12000 c0c93f70
3f60: c04bd630 c04bd5bc 200f0013 ffffffff c04bd574 c071bd24 7d50c9b4 c0719a44
3f80: 7d50c9b4 0000015b c0c9a498 c0c92028 c0c9a498 c0c9a4fc ea7a0e40 c0c8ee38
3fa0: c0d460e8 c0276198 00000000 c0d8291a 00000000 c0c9a400 00000000 c0be0bc4
3fc0: ffffffff ffffffff c0be05f8 00000000 00000000 c0c533d8 c0d82ed4 c0c9a47c
3fe0: c0c533d4 c0c9e870 8020406a 511f06f0 00000000 80208074 00000000 00000000
[<c021efc0>] (v7_dma_inv_range) from [<c021af18>] (__dma_page_dev_to_cpu+0x80/0x100)
[<c021af18>] (__dma_page_dev_to_cpu) from [<c021b574>] (arm_dma_unmap_sg+0x5c/0x84)
[<c021b574>] (arm_dma_unmap_sg) from [<c072ea58>] (mmci_dma_unmap.isra.16+0x60/0x74)
[<c072ea58>] (mmci_dma_unmap.isra.16) from [<c072f534>] (mmci_data_irq+0x1fc/0x29c)
[<c072f534>] (mmci_data_irq) from [<c072f6b4>] (mmci_irq+0xe0/0x114)
[<c072f6b4>] (mmci_irq) from [<c0280a60>] (handle_irq_event_percpu+0x78/0x134)
[<c0280a60>] (handle_irq_event_percpu) from [<c0280b60>] (handle_irq_event+0x44/0x64)
[<c0280b60>] (handle_irq_event) from [<c028369c>] (handle_fasteoi_irq+0xa8/0x1a8)
[<c028369c>] (handle_fasteoi_irq) from [<c0280278>] (generic_handle_irq+0x2c/0x3c)
[<c0280278>] (generic_handle_irq) from [<c020f080>] (handle_IRQ+0x40/0x90)
[<c020f080>] (handle_IRQ) from [<c02088e4>] (gic_handle_irq+0x38/0x68)
[<c02088e4>] (gic_handle_irq) from [<c0212800>] (__irq_svc+0x40/0x54)
Exception stack(0xc0c93f28 to 0xc0c93f70)
3f20: 00000001 a987c000 c0c93f3c c04bd574 00000000 0000015b
3f40: ea7a0e40 00000000 c0d460e8 c0d460e8 c0c92000 c08ea538 29b12000 c0c93f70
3f60: c04bd630 c04bd5bc 200f0013 ffffffff
[<c0212800>] (__irq_svc) from [<c04bd5bc>] (msm_cpu_pm_enter_sleep+0x48/0x4c)
[<c04bd5bc>] (msm_cpu_pm_enter_sleep) from [<c071bd24>] (qcom_lpm_enter_spc+0x20/0x2c)
[<c071bd24>] (qcom_lpm_enter_spc) from [<c0719a44>] (cpuidle_enter_state+0x44/0xf0)
[<c0719a44>] (cpuidle_enter_state) from [<c0276198>] (cpu_startup_entry+0x1f4/0x238)
[<c0276198>] (cpu_startup_entry) from [<c0be0bc4>] (start_kernel+0x384/0x390)
Code: 1e070f3e e1110003 e1c11003 1e071f3e (ee070f36)
---[ end trace cf6cb3f6432c9834 ]---
Kernel panic - not syncing: Fatal exception in interrupt
Reported-by: Nicolas Dechesne <nicolas.dechesne@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In mmc_init_card function some of the branches in error handling paths
go to "err" label, which skips removing of newly allocated card structure,
that will actually not be used. Fix that by using proper "free_card" label.
Also, some messages in these branches are reported as warnings,
although the operation processing is not continued. Change these
messages to error level.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The debug messages with commands execution results, that are printed
after processing the request, do not include results of sbc (set block count)
part of request. Add the debug message for that part too.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some request fields are initialized just before request processing
for sanity purposes. This is done for command, data, and stop parts
of the request, but not for sbc (set block count) part. Add such
initialization for that part too.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add the case of SET_BLOCK_COUNT command error to the error conditions
check for making a controller reset at request handling finish.
Otherwise, if the SET_BLOCK_COUNT command failed, e.g. with a timeout,
the controller state was not reset, and the next command failed too.
In the case of data error the controller reset is already done in
finish_data() function before sending stop command (if present),
so the finish tasklet should make a reset after data error only
if no stop command existed in the request.
Also, fix the indentation of this condition check to make it more logical.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As a follow-up of commit
"mmc: sdhci: Balance vmmc regulator_enable(), and always enable vqmmc"
vmmc regulator disable is also not needed in sdhci_remove_host.
The regulator is completely controlled by mmc_power_up and mmc_power_off
functions and is already disabled by the time of removing the host.
Extra regulator_disable call in sdhci_remove_host is unbalanced and
causes a warning reported by regulator core, so should be removed.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The commit ad93220de7 ("mmc: sdhci-esdhc-imx: change pinctrl state
according to uhs mode") exits the probe in case there are no valid
pinctrl states found.
As there are configurations doing the pin mux properly in the boot
loader, don't exit. Just warn, but go on in case if there are no
pinctrl states in the device tree.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If available voltages are not given, mmc_regulator_get_supply() function
returns 0 and mxcmmc driver doesn't set a value for ocr_avail mask.
In accordance with the comment in platform_data/mmc-mxcmmc.h,
fix it, assuming MMC_VDD_32_33 | MMC_VDD_33_34 as default value.
Signed-off-by: Matteo Facchinetti <matteo.facchinetti@sirius-es.it>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
During a read of data block using dma, driver might have two ways to finish to read
and free the resources:
1) checking STATUS_DATA_TRANS_DONE mask, in the mxcmci_irq() routine
(pending to mmc irq)
2) mxmmc driver, registers also a mxcmci_dma_callback() and when transfer is finished,
dma driver calls this callback. (pending to dma irq)
Both ways are concurrent with each other.
Race condition happens when following events occur:
/* (1) mxcmci driver start data transfer */
158.418970: mpc_dma_execute: mpc_dma_execute(): will_access_peripheral start cid=31
158.418976: mpc_dma_issue_pending <-mxcmci_request
158.418983: mxcmci_start_cmd <-mxcmci_request
/* (2) mxcmci driver receive mmc irq */
158.419656: mxcmci_irq <-handle_irq_event_percpu
158.419692: mxcmci_read_response <-mxcmci_irq
/* (3) mxcmci driver checks that transfer is complete and call mxcmci_finish_data() */
158.419726: mxcmci_data_done <-mxcmci_irq
158.419729: mxcmci_finish_data <-mxcmci_data_done
158.419733: dma_direct_unmap_sg <-mxcmci_finish_data
158.419736: mxcmci_swap_buffers.isra.24 <-mxcmci_finish_data
158.419762: mxcmci_read_response <-mxcmci_data_done
/* (4) mxcmci driver (no dma): send stop command */
158.419765: mxcmci_start_cmd <-mxcmci_data_done
/* (5) mxcmci driver (no dma): receive the stop command irq response */
158.419782: mxcmci_irq <-handle_irq_event_percpu
158.419812: mxcmci_read_response <-mxcmci_irq
158.419843: mxcmci_finish_request <-mxcmci_irq
/* (6) dma driver: receive dma irq (finish data transfer) related by request on step 1 */
158.419853: mpc_dma_irq <-handle_irq_event_percpu
158.420001: mpc_dma_irq_process <-mpc_dma_irq
158.420004: mpc_dma_irq_process <-mpc_dma_irq
/* (7) dma driver: start dma tasklet to finish the dma irq handling */
158.420008: mpc_dma_irq_process: mpc_dma_irq_process(): completed ch:31
/* (8) mxcmci driver: start next data transfer using dma */
158.420174: mxcmci_request <-mmc_start_req
158.420182: dma_direct_map_sg <-mxcmci_request
158.420192: mpc_dma_prep_slave_sg <-mxcmci_request
/* (9) dma driver: schedule irq tasklet and execute mxcmci dma driver callback */
158.420250: mpc_dma_tasklet <-tasklet_action
158.420254: mpc_dma_process_completed <-tasklet_action
158.420267: mxcmci_dma_callback <-mpc_dma_process_completed
/* ERROR!!! (10) mxcmci driver callback works on dma data related to the step 1
that is already finished */
158.420271: mxcmci_data_done <-mpc_dma_process_completed
158.420273: mxcmci_finish_data <-mxcmci_data_done
/* ERROR!!! (11) mxcmci driver: clear data that should be used by step 8 and
send an other mmc stop command (already sended on step 4) */
158.420276: dma_direct_unmap_sg <-mxcmci_finish_data
158.420279: mxcmci_swap_buffers.isra.24 <-mxcmci_finish_data
158.420330: mxcmci_read_response <-mxcmci_data_done
158.420333: mxcmci_start_cmd <-mxcmci_data_done
158.420338: dma_run_dependencies <-mpc_dma_process_completed
...
...
...
168.474223: mxcmci_watchdog <-call_timer_fn
168.474236: mxcmci_watchdog: mxcmci_watchdog
168.474397: mpc_dma_device_control <-mxcmci_watchdog
In accordance with the other drivers that using the dma engine,
fix it, leaving *only* to dma driver the complete control to
ending the read operation.
Removing STATUS_READ_OP_DONE event activation, has as effect
to force mxcmci driver to handle the finish data transfer only
by mxcmci dma callback.
Signed-off-by: Matteo Facchinetti <matteo.facchinetti@sirius-es.it>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since commit 89168b4899 ("mmc: core: restore detect line inversion
semantics"), the SD card on i.MX28 (and possibly other) devices isn't
detected and booting stops at:
[ 4.120617] Waiting for root device /dev/mmcblk0p3...
This is caused by the MMC_CAP2_CD_ACTIVE_HIGH flag being set incorrectly
when the host controller doesn't use a GPIO for card detection (but
instead uses a dedicated pin). In this case mmc_gpiod_request_cd() will
return before assigning to the gpio_invert variable, leaving the
variable uninitialized. The variable then gets used to set the flag.
This patch fixes the issue by making sure gpio_invert is set to false
when a GPIO isn't used. After this patch, i.MX28 boots fine.
The MMC_CAP2_RO_ACTIVE_HIGH (write protect) flag is also set incorrectly
for the exact same reason (it uses the same uninitialized variable), so
this patch fixes that too.
Fixes: 89168b4899 ("mmc: core: restore detect line inversion semantics")
Reported-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Kristina Martšenko <kristina.martsenko@gmail.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Pull block layer driver update from Jens Axboe:
"This is the block driver pull request for 3.18. Not a lot in there
this round, and nothing earth shattering.
- A round of drbd fixes from the linbit team, and an improvement in
asender performance.
- Removal of deprecated (and unused) IRQF_DISABLED flag in rsxx and
hd from Michael Opdenacker.
- Disable entropy collection from flash devices by default, from Mike
Snitzer.
- A small collection of xen blkfront/back fixes from Roger Pau Monné
and Vitaly Kuznetsov"
* 'for-3.18/drivers' of git://git.kernel.dk/linux-block:
block: disable entropy contributions for nonrot devices
xen, blkfront: factor out flush-related checks from do_blkif_request()
xen-blkback: fix leak on grant map error path
xen/blkback: unmap all persistent grants when frontend gets disconnected
rsxx: Remove deprecated IRQF_DISABLED
block: hd: remove deprecated IRQF_DISABLED
drbd: use RB_DECLARE_CALLBACKS() to define augment callbacks
drbd: compute the end before rb_insert_augmented()
drbd: Add missing newline in resync progress display in /proc/drbd
drbd: reduce lock contention in drbd_worker
drbd: Improve asender performance
drbd: Get rid of the WORK_PENDING macro
drbd: Get rid of the __no_warn and __cond_lock macros
drbd: Avoid inconsistent locking warning
drbd: Remove superfluous newline from "resync_extents" debugfs entry.
drbd: Use consistent names for all the bi_end_io callbacks
drbd: Use better variable names
- Fix SDIO IRQ bug.
- MMC regulator improvements.
- Fix slot-gpio card detect bug.
- Add support for Driver Stage Register.
- Convert the common MMC OF parser to use GPIO descriptors.
- Convert MMC_CAP2_NO_MULTI_READ into a callback, ->multi_io_quirk().
- Some additional minor fixes.
MMC host:
- mmci: Support Qualcomm specific DML layer for DMA.
- dw_mmc: Use common MMC regulators.
- dw_mmc: Add support for Rock-chips RK3288.
- tmio: Enable runtime PM support.
- tmio: Add support for R-Car Gen2 SoCs.
- tmio: Several fixes and improvements.
- omap_hsmmc: Removed Balaji from MAINTAINERS.
- jz4740: add DMA and pre/post support.
- sdhci: Add support for Intel Braswell.
- sdhci: Several fixes and improvements.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=VFRY
-----END PGP SIGNATURE-----
Merge tag 'mmc-v3.18-1' of git://git.linaro.org/people/ulf.hansson/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Fix SDIO IRQ bug
- MMC regulator improvements
- Fix slot-gpio card detect bug
- Add support for Driver Stage Register
- Convert the common MMC OF parser to use GPIO descriptors
- Convert MMC_CAP2_NO_MULTI_READ into a callback, ->multi_io_quirk()
- Some additional minor fixes
MMC host:
- mmci: Support Qualcomm specific DML layer for DMA
- dw_mmc: Use common MMC regulators
- dw_mmc: Add support for Rock-chips RK3288
- tmio: Enable runtime PM support
- tmio: Add support for R-Car Gen2 SoCs
- tmio: Several fixes and improvements
- omap_hsmmc: Removed Balaji from MAINTAINERS
- jz4740: add DMA and pre/post support
- sdhci: Add support for Intel Braswell
- sdhci: Several fixes and improvements"
* tag 'mmc-v3.18-1' of git://git.linaro.org/people/ulf.hansson/mmc: (119 commits)
ARM: dts: fix MMC2 regulators for Exynos5420 Arndale Octa board
mmc: sdhci-acpi: Fix Braswell eMMC timeout clock frequency
mmc: sdhci-acpi: Pass HID and UID to probe_slot
mmc: sdhci-acpi: Get UID directly from acpi_device
mmc, sdhci, bcm-kona, LLVMLinux: Remove use of __initconst
mmc: sdhci-pci: Fix Braswell eMMC timeout clock frequency
mmc: sdhci: Let a driver override timeout clock frequency
mmc: sdhci-pci: Add Bay Trail and Braswell SD card detect
mmc: sdhci-pci: Set SDHCI_QUIRK2_STOP_WITH_TC for Intel BYT host controllers
mmc: sdhci-acpi: Add a HID and UID for a SD Card host controller
mmc: sdhci-acpi: Set SDHCI_QUIRK2_STOP_WITH_TC for Intel host controllers
mmc: sdhci: Add quirk for always getting TC with stop cmd
mmc: core: restore detect line inversion semantics
mmc: Fix incorrect warning when setting 0 Hz via debugfs
mmc: Fix use of wrong device in mmc_gpiod_free_cd()
mmc: atmel-mci: fix mismatched section on atmci_cleanup_slot
mmc: rtsx_pci: Set power related cap2 macros
mmc: core: Add new power_mode MMC_POWER_UNDEFINED
mmc: sdhci: execute tuning when device is not busy
mmc: atmel-mci: Release mmc resources on failure in probe
..
Braswell eMMC host controller specifies an incorrect
timeout clock frequncy in the capabilities registers.
The correct value is 1 MHz. A similar fix was done
for sdhci-pci, however in the sdhci-acpi case the
HID/UID is not unique so the capabilities register
values are matched also.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Pass HID and UID to probe_slot so extra setup
can be done for specific ids.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
UID was made available on acpi_device since
commit ccf7804026 ("ACPI: Add _UID support for ACPI devices.")
Use it from there instead of reprocessing the
ACPI object info.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Clear QUEUE_FLAG_ADD_RANDOM in all block drivers that set
QUEUE_FLAG_NONROT.
Historically, all block devices have automatically made entropy
contributions. But as previously stated in commit e2e1a148 ("block: add
sysfs knob for turning off disk entropy contributions"):
- On SSD disks, the completion times aren't as random as they
are for rotational drives. So it's questionable whether they
should contribute to the random pool in the first place.
- Calling add_disk_randomness() has a lot of overhead.
There are more reliable sources for randomness than non-rotational block
devices. From a security perspective it is better to err on the side of
caution than to allow entropy contributions from unreliable "random"
sources.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The __initconst is in the wrong place, and when moved to the correct place
it uncovers an error where the variable is used by non-init data structures.
Instead merely make them const and put the const in the right spot.
Signed-off-by: Behan Webster <behanw@converseincode.com>
Reviewed-by: Mark Charlebois <charlebm@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Matt Porter <mporter@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Braswell eMMC host controller specifies an incorrect
timeout clock frequncy in the capabilities registers.
The correct value is 1 MHz.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Let a driver override the timeout clock frequency by
populating it before calling sdhci_add_host(). Note
the value will otherwise be zero because sdhci_host is
zeroed when allocated.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support for card detect for Bay Trail
and Braswell SD Card host controllers in PCI
mode.
This uses the gpio descriptor API which can find
gpio descriptors, for example, on an ACPI comapnion
device.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a HID (INT33BB) and UID (3) for a SD Card host controller.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a quirk for a host controller that always sets
a Transfer Complete interrupt status for the stop
command even when a busy response is not indicated.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
commit 98e90de99a
"mmc: host: switch OF parser to use gpio descriptors"
switched the semantic behaviour of card detect and read
only flags such that the inversion capability flag would
only be set if inversion was explicitly specified in the
device tree, in the hopes that no-one was using double
inversion.
It turns out that the XOR:ing between the explicit
inversion was indeed in use, so we need to restore the
old semantics where both ways of inversion are checked
and the end result XOR:ed.
Reported-by: Javier Martinez Canillas <javier@dowhile0.org>
Tested-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The commit 46420dd73b (PM / Domains: Add APIs to attach/detach a PM
domain for a device) started using errno values in pm.h header file.
It also failed to include the header for these, thus it caused
compiler errors.
Instead of including the errno header to pm.h, let's move the functions
to pm_domain.h, since it's a better match.
Fixes: 46420dd73b (PM / Domains: Add APIs to attach/detach a PM domain for a device)
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
It is possible to turn off the card clock by setting
the frequency to zero via debugfs e.g.
echo 0 > /sys/kernel/debug/mmc0/clock
However that produces an incorrect warning that is
designed to warn if the frequency is below the minimum
operating frequency. So correct the warning.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_gpiod_free_cd() is paired with mmc_gpiod_request_cd()
and both must reference the same device which is the
actual host controller device not the mmc_host class
device.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As of 528bc7808f ("mmc: atmel-mci: Release mmc resources on failure in probe"),
the atmci_probe() function calls atmci_cleanup_slot in the failure path.
This causes a new warning whenever the driver is built:
WARNING: drivers/mmc/host/built-in.o(.init.text+0xa04): Section mismatch in reference from the function atmci_probe() to the function .exit.text:atmci_cleanup_slot()
The function __init atmci_probe() references
a function __exit atmci_cleanup_slot().
Gcc correctly warns about this function getting dropped in the link stage
for the built-in case, which would cause undefined behavior when this error
path is hit. The solution is to simply drop the __exit annotation.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 528bc7808f ("mmc: atmel-mci: Release mmc resources on failure in probe")
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Set MMC_CAP2_NO_PRESCAN_POWERUP and MMC_CAP2_FULL_PWR_CYCLE for
rtsx_pci_sdmmc and rtsx_usb_sdmmc to reflect properties of Realtek
card reader hosts.
Signed-off-by: Roger Tseng <rogerable@realtek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add MMC_POWER_UNDEFINED for power_mode in struct mmc_ios and use it as
the initial value of host->ios.power_mode.
For hosts with MMC_CAP2_NO_PRESCAN_POWERUP, this makes the later
mmc_power_off() do real power-off things instead of NOP, and further
prevents state messed up in cards that was already initialized (eg. by
BIOS of UEFI driver).
Signed-off-by: Roger Tseng <rogerable@realtek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We find tuning timeout because of the secure erase operation lasts too
long, so don't do tuning when device is busy.
Signed-off-by: Yi Sun <yi.y.sun@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This change takes care of releasing mmc resources on error cases in
probe function which was missing. Also release timer in remove function.
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This change uses managed resource APIs to allocate resources such as,
clk, gpio, io in order to simplify the driver unload or failure cases.
Hence does away with release statements of the same resources in error
labels and remove function.
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use the much more common pr_warn instead of pr_warning.
Other miscellanea:
o Coalesce formats
o Realign arguments
o Remove extra spaces when coalescing formats
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The same tuning block exists in the dw_mmc h.c and sdhci-msm.c
files. Move these into mmc.c so that they can be shared across
drivers.
Reported-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If we're tuning on a big-endian CPU we'll never determine we properly
tuned the device because we compare the data we received from the
controller with a table that assumes the CPU is little-endian.
Change the table to be an array of bytes instead of 32-bit words
so we can use memcmp() without needing to byte-swap every word
depending on the endianess of the CPU.
Cc: Asutosh Das <asutoshd@codeaurora.org>
Cc: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Reviewed-by: Georgi Djakov <gdjakov@mm-sol.com>
Fixes: 415b5a75da "mmc: sdhci-msm: Add platform_execute_tuning implementation"
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As soon as the CD IRQ is requested, it can trigger, since it's an
externally controlled event. If it does, delayed_work host->detect will
be scheduled.
Many host controller probe()s are roughly structured as:
*_probe() {
host = sdhci_pltfm_init();
mmc_of_parse(host->mmc);
rc = sdhci_add_host(host);
if (rc) {
sdhci_pltfm_free();
return rc;
}
In 3.17, CD IRQs can are enabled quite early via *_probe() ->
mmc_of_parse() -> mmc_gpio_request_cd() -> mmc_gpiod_request_cd_irq().
Note that in linux-next, mmc_of_parse() calls mmc_gpio*d*_request_cd()
rather than mmc_gpio_request_cd(), and mmc_gpio*d*_request_cd() doesn't
call mmc_gpiod_request_cd_irq(). However, this issue still exists if
mmc_gpio_request_cd() is called directly before mmc_start_host().
sdhci_add_host() may fail part way through (e.g. due to deferred
probe for a vmmc regulator), and sdhci_pltfm_free() does nothing to
unrequest the CD IRQ nor cancel the delayed_work. sdhci_pltfm_free() is
coded to assume that if sdhci_add_host() failed, then the delayed_work
cannot (or should not) have been triggered.
This can lead to the following with CONFIG_DEBUG_OBJECTS_* enabled, when
kfree(host) is eventually called inside sdhci_pltfm_free():
WARNING: CPU: 2 PID: 6 at lib/debugobjects.c:263 debug_print_object+0x8c/0xb4()
ODEBUG: free active (active state 0) object type: timer_list hint: delayed_work_timer_fn+0x0/0x18
The object being complained about is host->detect.
There's no need to request the CD IRQ so early; mmc_start_host() already
requests it. For most SDHCI hosts at least, the typical call path that
does this is: *_probe() -> sdhci_add_host() -> mmc_add_host() ->
mmc_start_host(). Therefore, remove the call to mmc_gpiod_request_cd_irq()
from mmc_gpio_request_cd(). This also matches mmc_gpio*d*_request_cd(),
which already doesn't call mmc_gpiod_request_cd_irq().
However, some host controller drivers call mmc_gpio_request_cd() after
mmc_start_host() has already been called, and assume that this will also
call mmc_gpiod_request_cd_irq(). Update those drivers to explicitly call
mmc_gpiod_request_cd_irq() themselves. Ideally, these drivers should be
modified to move their call to mmc_gpio_request_cd() before their call
to mmc_add_host(). However that's too large a change for stable.
This solves the problem (eliminates the kernel error message above),
since it guarantees that the IRQ can't trigger before mmc_start_host()
is called.
The critical point here is that once sdhci_add_host() calls
mmc_add_host() -> mmc_start_host(), sdhci_add_host() is coded not to
fail. In other words, if there's a chance that mmc_start_host() may have
been called, and CD IRQs triggered, and the delayed_work scheduled,
sdhci_add_host() won't fail, and so cleanup is no longer via
sdhci_pltfm_free() (which doesn't free the IRQ or cancel the work queue)
but instead must be via sdhci_remove_host(), which calls mmc_remove_host()
-> mmc_stop_host(), which does free the IRQ and cancel the work queue.
CC: Russell King <linux@arm.linux.org.uk>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexandre Courbot <acourbot@nvidia.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Previously only the ACPI PM domain was supported by the sdio bus.
Let's convert to the common attach/detach functions for PM domains,
which currently means we are extending the support to include the
generic PM domain as well.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
I spent a couple of days with the driver just hanging due to me forgetting to
specify the external crystal frequency, so that clk_get_rate() returned 0 and
thus the loop in tmio_mmc_set_clock() never ended. I don't think that's an
acceptable behavior, so I suggest that the minimum frequency is checked for 0
in tmio_mmc_host_probe().
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Ian Molton <ian.molton@codethink.co.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current tmio is using sd_ctrl_read16/write16_rep()
for data transfer.
It works if transfer size was even number,
but, last 1 byte will be ignored if
transfer size was odd number.
This patch adds new tmio_mmc_transfer_data()
and solve this issue.
Tested-by: Shinobu Uehara <shinobu.uehara.xc@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Stop command errors are not fatal to the transfer since we make sure
that the card returns to the transfer state and check the card status.
Change an unnecessary error to an info.
Signed-off-by: Johan Rudholm <johanru@axis.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dw_mci_of_find_slot_node() is only used in dw_mci_of_get_slot_quirks()
if CONFIG_OF is defined, thus there is no need to have a !CONFIG_OF
version of it. Fixes the following compile warning with !CONFIG_OF:
CC [M] drivers/mmc/host/dw_mmc.o
drivers/mmc/host/dw_mmc.c:2223:28: warning: ‘dw_mci_of_find_slot_node’ defined but not used [-Wunused-function]
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Checks EXT_CSD_PARTITION_SETTING_COMPLETED bit before
computing enhanced user area offset and size, and
adding mmc general purpose partitions. The two needs
EXT_CSD_PARTITION_SETTING_COMPLETED bit be set to be
valid (as described in JEDEC standard).
Warn user in case of misconfiguration.
Signed-off-by: Grégory Soutadé <gsoutade@neotion.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Replace ext_csd "enhanced_area_en" attribute by
"partition_setting_completed". It was used whether or
not enhanced user area is defined and without checks of
EXT_CSD_PARTITION_SETTING_COMPLETED bit.
Signed-off-by: Grégory Soutadé <gsoutade@neotion.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Move code that manages user area and general purpose
partitions into functions.
Signed-off-by: Grégory Soutadé <gsoutade@neotion.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 0dcaa2499b improved error
handling of sdhci_add_host. However, "err_of_parse" and "err_cd_req"
should be placed after "pm_runtime_disable(&pdev->dev)".
Signed-off-by: Xiang Wang <wangx@marvell.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch renames sdio flag in vendor data to st_sdio, as this flag is
only used to enable ST specific sdio setup. This will also ensure that
the ST specfic setup is not done on other vendor like Qualcomm.
Originally the issue was detected while testing WLAN ath6kl on IFC6410
board with APQ8064 SOC.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds sdio enable mask in variant data, SOCs like ST have
special bits in datactrl register to enable sdio. Unconditionally setting
this bit in this driver breaks other SOCs like Qualcomm which maps this
bits to something else, so making this enable bit to come from variant
data solves the issue.
Originally the issue is detected while testing WLAN ath6kl on Qualcomm
APQ8064.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently the MMCI driver will only handle GPIO descriptors
implicitly through the device tree probe glue in mmc_of_init(),
but devices instatiated other ways such as through board files
and passing descriptors using the GPIO descriptor table will
not be able to exploit descriptors.
Augment the driver to look for a GPIO descriptor if device
tree is not used for the device, and if that doesn't work,
fall back to platform data GPIO assignment using the old
API. The end goal is to get rid of the platform data integer
GPIO assingments from the kernel.
This enable the MMCI-embedding platforms to be converted to
GPIO descritor tables.
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This switches the central MMC OF parser to use gpio descriptors
instead of grabbing GPIOs explicitly from the device tree.
This strips out an unecessary use of the integer-based GPIO
API that we want to get rid of, cuts down on code as the
gpio descriptor code will handle active low flags.
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This makes it possible to get the write protect (read only)
GPIO line from a GPIO descriptor. Written to exactly mirror
the card detect function.
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When the slot GPIO driver gets the GPIO to be used for card
detect, it is now possible to specify a flag to have the line
set up as input. Get rid of the explicit setup call for input
and use the flag.
The extra argument works as there are transition varargs
macros in place in the <linux/gpio/consumer.h> header, in
the future we will make the flags argument compulsory.
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It seems very unlikely that eMMC devices would hold a standard
partitiontable in one of it's boot areas. Therefore, let's prevent
them from being scanned.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now, sh_mobile_sdhi can use .multi_io_quirk callback
instead of MMC_CAP2_NO_MULTI_READ flags.
let's use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now, tmio_mmc can use .multi_io_quirk callback
instead of MMC_CAP2_NO_MULTI_READ flags.
let's use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now, omap_hsmmc can use .multi_io_quirk callback
instead of MMC_CAP2_NO_MULTI_READ flags.
let's use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Due to HW issue, SDHCI host controller on Intel
Baytrail/Merrifield platforms can not use preset
register. So, disable preset registers for them by quirks.
Signed-off-by: Yunpeng Gao <yunpeng.gao@intel.com>
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Historically, we have been using MMC_CAP* to handle host HW issues and
currently the block layer uses MMC_CAP2_NO_MULTI_READ flag for a multi
I/O HW bug workaround.
There are a few tweaks needed to make MMC_CAP2_NO_MULTI_READ suite all
situations. Therefore let's add an optional host ops callback to enable
host drivers to return the number of blocks it allows per request.
In a future patch and when host drivers have converted to the new
callback, MMC_CAP2_NO_MULTI_READ shall be removed.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Right now enable 1.2v IO voltage for SDHC is by using vqmmc.
Thus for the host which doesn't have vqmmc, or its vqmmc does
not support 1.2v, directly use MMC_CAP2_HS200 may cause HS200
failure.
So needs to check if vqmmc is able to support 1.2v. If it does
not support, disable 1.2v IO for HS200.
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Even (e)MMC card can support 3.3v to 1.2v vccq in DDR, but not all
host controller can support this, like some of the SDHCI host
which connect to an eMMC device. Some of these host controller
still needs to use 1.8v vccq for supporting DDR mode.
So the sequence will be:
if (host and device can both support 1.2v IO)
use 1.2v IO;
else if (host and device can both support 1.8v IO)
use 1.8v IO;
so if host and device can only support 3.3v IO, this is the last choice.
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: Yunpeng Gao <yunpeng.gao@intel.com>
Tested-by: Jean-Michel Hautbois <jhautbois@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add the clock prepare and unprepare call to the driver set_ios calls
phase. This will remove a warning once the PXA architecture is migrated
to the clock infrastructure.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Similar to sdhci-pci controller, also add probe_slot
and remove_slot method in the sdhci-acpi driver.
Signed-off-by: Yunpeng Gao <yunpeng.gao@intel.com>
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It is fully legal for a controller to start handling busy-end interrupt
before it has signaled that the command has completed. So make sure
we do things in the proper order, Or it results that command interrupt
is ignored so it can cause unexpected operations. This is founded at some
toshiba emmc with the bellow warning.
"mmc0: Got command interrupt 0x00000001 even though
no command operation was in progress."
This issue has been also reported by Youssef TRIKI:
It is not specific to Toshiba devices, and happens with eMMC devices
as well as SD card which support Auto-CMD12 rather than CMD23.
Also, similar patch is submitted by:
Gwendal Grignou <gwendal@chromium.org>
Changes since v1:
Fixed conflict with the next of git.linaro.org/people/ulf.hansson/mmc.git
and Tested if issue is fixed again.
Signed-off-by: Hankyung Yu <hankyung.yu@lge.com>
Signed-off-by: Chanho Min <chanho.min@lge.com>
Tested-by: Youssef TRIKI <youssef.triki@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci_disable_irq_wakeups() is exported, but it is not called outside sdhci.c.
Make it static and do not export it, so that the following sparse warning is
fixed:
drivers/mmc/host/sdhci.c:2548:6: warning: symbol 'sdhci_disable_irq_wakeups' was not declared. Should it be static?
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The timeout_clk calculation code for SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK case
is common and could be moved into common sdhci_do_set_ios, then platform code
which is not using sdhci_set_clock does not need to write the same code again.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The timeout_clk calculation code in sdhci_add_host is meaningless for
SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK.
So only execute them with no SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK set.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The default sdhci driver write 0xE into timeout counter register to
set the maximum timeout. The value is not correct for uSDHC since the
max counter value for uSDHC is 0xF.
Instead of using common timeout code in sdhci, we implement esdhc_set_timeout
to handle the difference between eSDHC and uSDHC.
Currently we simply set the max timeout value as before.
But in the future, we probably may implement IMX specific timeout
setting algorithm and use suitable timeout for different CMDs.
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently the common code assume 0xE is the maximum timeout counter
value and use it to write into the timeout counter register.
However, it's fairly possible that some other SoCs may have different
max timeout register value. That means 0xE may be incorrect and
becomes meaningless.
It's also possible that other platforms has different timeout
calculation algorithm. To be flexible, this patch provides a .set_timeout
hook for those platforms to set the timeout on their way if they need.
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The default sdhci code use the 1 << 27 as the max timeout counter to
to calculate the max_busy_timeout, however it's not correct for uSDHC
since its the max counter is 1 << 28.
Implement esdhc_get_max_timeout_cout to handle it correctly.
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently the max timeout count is hardcode to 1 << 27 for calcuate
the max_busy_timeout, however, for some platforms the max timeout
count may not be 1 << 27, e.g. i.MX uSDHC is 1 << 28.
Thus 1 << 27 is not correct for such platform.
It is also possible that other platforms may have different values.
To be flexible, we add a get_max_timeout_count hook to get the correct
maximum timeout value for these platforms.
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It's possible that mmc_of_parse() could return errors (possibly in
some future version it might return -EPROBE_DEFER even). Let's pass
those errors back.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
the implementation of CSR SDHCI controller is a modified version of
the one described in the 1.0 specification, and not a normal 3.0
controller.
and 8bit-width enable bit of CSR MMC hosts is 3, while stardard hosts
use bit 5.
this patch fixes the functionality of 8bit transfer in mmc controllers
and improve performance for mmc0 a lot.
Signed-off-by: Minda Chen <Minda.Chen@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Reviewed-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For UHS cards we need the ability to switch voltages from 3.3V to
1.8V. Add support to the dw_mmc driver to handle this. Note that
dw_mmc needs a little bit of extra code since the interface needs a
special bit programmed to the CMD register while CMD11 is progressing.
This means adding a few extra states to the state machine to track.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch makes use of mmc_regulator_get_supply() to handle
the vmmc and vqmmc regulators.Also it moves the code handling
the these regulators to dw_mci_set_ios().It turned on the vmmc
and vqmmc during MMC_POWER_UP and MMC_POWER_ON,and turned off
during MMC_POWER_OFF.
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Declare ERASE capability so we can use filesystems with the discard
option and the fstrim tool.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The hardware is the same as used in Baytrail. Add these new PCI IDs to the
driver's list of supported IDs.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To support HS200 and UHS-1, we need add a big hunk of code,
as shown in the following patches. So a separate file for
rockchip SOCs is suitable.
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some controller is supporting actual clock on SD_CLK_CTRL :: DIV[7:0].
Renesas SH-Mobile SDHI doesn't support,
but, Renesas R-Car SDHI supports it.
This patch adds new TMIO_MMC_CLK_ACTUAL flag for it.
[Kuninori Morimoto: tidyuped for upstreaming]
Tested-by: Nguyen Xuan Nui <nx-nui@jinso.co.jp>
Tested-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Signed-off-by: Shinobu Uehara <shinobu.uehara.xc@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
TMIO clock is set via tmio_mmc_set_clock() -> tmio_mmc_clk_start(),
and SCLKEN bit will be set on tmio_mmc_clk_start().
It is not needed on tmio_mmc_set_clock() function.
The required clock setting will not be able to set
in some clocks without this patch.
Tested-by: Nguyen Xuan Nui <nx-nui@jinso.co.jp>
Tested-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds new TMIO_MMC_HAVE_CTL_DMA_REG flag,
and remove Renesas specific #ifdef from tmio driver
Tested-by: Nguyen Xuan Nui <nx-nui@jinso.co.jp>
Tested-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some controllers need to check SD bus status when writing data.
Then, it checks ILL_FUNC bit on SD_INFO2 register,
and this method is controlled via TMIO_MMC_HAS_IDLE_WAIT flags.
Same method is required on tmio_mmc_data_irq() which will
be called after writing data.
Current driver is checking CBSY bit for this purpose,
but, some controllers doesn't have CBSY bit.
This patch checks ILL_FUNC bit instead of CBSY bit
if it has TMIO_MMC_HAS_IDLE_WAIT flags
[Kuninori Morimoto: tidyuped for upstreaming]
Tested-by: Nguyen Xuan Nui <nx-nui@jinso.co.jp>
Tested-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Signed-off-by: Shinobu Uehara <shinobu.uehara.xc@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Renesas R-Car SDHI should set reserved bits
on CTL_SDIO_STATUS register when writing.
This patch adds new TMIO_MMC_SDIO_STATUS_QUIRK flags
for this purpose
[Kuninori Morimoto: tidyuped for upstreaming
enabled this flags for all SH-Mobile/R-Car]
Tested-by: Nguyen Xuan Nui <nx-nui@jinso.co.jp>
Tested-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Signed-off-by: Shinobu Uehara <shinobu.uehara.xc@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Renesas SDHI has "Multiple Block Transfer Mode" settings
on SD_CMD register which controls CMD12 automatically.
This patch cares it, because
CMD12 is not needed when CMD53 (= SD_IO_RW_EXTENDED)
[Kuninori Morimoto: tidyuped for upstreaming
enabled this flags for all SH-Mobile/R-Car]
Tested-by: Nguyen Xuan Nui <nx-nui@jinso.co.jp>
Tested-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Signed-off-by: Shinobu Uehara <shinobu.uehara.xc@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Next card access will be always
error if it didn't clear error status
Tested-by: Nguyen Xuan Nui <nx-nui@jinso.co.jp>
Tested-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Signed-off-by: Shinobu Uehara <shinobu.uehara.xc@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Basically, SD_BUF0 Tx/Rx addresses are same
in normal TMIO controller,
but, it is different on Renesas R-Car SDHI controller
if it uses DMAC
(Rx address needs to add 0x2000 to Tx address)
This patch adds new .dma_rx_offset and cares it
Tested-by: Nguyen Xuan Nui <nx-nui@jinso.co.jp>
Tested-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
These library functions aren't used and nor needed, let's remove them.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
At system PM suspend, the tmio core accessed the internal registers of
the controller without first moving the device into active state. This
caused a lock-up in system PM suspend phase.
The reason for the register access were masking of IRQs. Since that is
managed via the runtime PM suspend path, let's just re-use that path
for system PM suspend.
In other words force the device into runtime PM suspend state at system
PM suspend and restore it to active state at system PM resume.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
At system PM suspend, the tmio core accessed the internal registers of
the controller without first moving the device into active state. This
caused a lock-up in system PM suspend phase.
The reason for the register access were masking of IRQs. Since that is
managed via the runtime PM suspend path, let's just re-use that path
for system PM suspend.
In other words force the device into runtime PM suspend state at system
PM suspend and restore it to active state at system PM resume.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
To take advantage of the clock gating support, use the runtime PM
callbacks provided by the tmio core.
Additionally, we make use of the SET_PM_RUNTIME_PM_OPS, which is a
preparation needed to simplify system PM.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
To be able to simplify system PM, let's re-use the runtime PM callbacks
by converting to the SET_PM_RUNTIME_PM_OPS macro.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
To give the option for tmio hosts to use the runtime PM callbacks for
CONFIG_PM_SLEEP as well as CONFIG_PM_RUNTIME, move them to CONFIG_PM.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
To make sure we don't receive any spurious IRQs while we are inactive,
mask the IRQs from within the ->runtime_suspend() callback.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add clock gating control as a part of the tmio library functions for
runtime PM.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
An internal power state machine were beeing used to keep ->probe() and
->set_ios() in sync. Especially for handling specific scenarios while
using CONFIG_MMC_CLKGATE. Moreover dependency to CONFIG_MMC_CLKGATE
existed to handle runtime PM properly, which we moves away from here.
By removing the state machine and instead make ->set_ios() rely on the
information provided through the function's in-parameters, the code
becomes significantly simplier.
Additonally as a part of this rework we prepares for making the runtime
PM callbacks responsible of clock gating.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Move code for bus_width modification, out of the ->set_ios() callback
and into a separate function, to simplify code.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Use runtime PM to keep the host active during I/O operations and other
requests which requires the tmio hardware to be powered.
Additionally make use of the runtime PM autosuspend feature with a
default timeout of 50 ms.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
The host must be kept active to be able to serve SDIO IRQs, thus let's
prevent it from going inactive while SDIO IRQ is enabled.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
The operation conditions register (OCR) stores the voltage
profile of the card, however the list of possible voltages
is restricted by the voltage range supported by the supply
used as VCC/VDD. So in mmc_vddrange_to_ocrmask() a OCR mask
is obtained to filter the not supported voltages, from the
value read in the host controller OCR register.
For fixed regulators, regulator_list_voltage() returns the
fixed output for the first selector but this doesn't happen
for switch (FET) regulators that obtain their voltage from
their parent supply. A call to regulator_get_voltage() is
needed in this case so the regulator core can return the
FET's parent supply voltage output.
This change is consistent with the fact that for other
fixed regulators (that are not FETs) the OCR mask is
returned even when mmc_regulator_set_ocr() checks if the
regulator is fixed before calling regulator_set_voltage().
Without this patch, the following warning is reported when
a FET is used as a vmmc-supply:
dwmmc_exynos 12220000.mmc: Failed getting OCR mask: -22
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some eMMC and SD cards implement a DSR register that allows to tune
raise/fall times and drive strength of the CMD and DATA outputs.
The values to use depend on the card in use and the host.
It might be needed to reduce the drive strength to prevent voltage peaks
above the host's specification.
Implement a 'dsr' devicetree property that allows to specify the value
to set the DSR to. For non-dt setups the new members of mmc_host can be
set by board code.
This patch was initially authored by Sascha Hauer. It contains
improvements authored by Markus Niebel and Uwe Kleine-König.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
.set_uhs_signaling field is currently initialised twice once to the
arch specific callback pxav3_set_uhs_signaling, and also to the generic
sdhci_set_uhs_signaling callback.
This means that uhs is currently broken for this platform currently, as pxav3
has some special constriants which means it can't use the generic callback.
This happened in
commit 96d7b78cfc ("mmc: sdhci: convert sdhci_set_uhs_signaling() into a library function")
commit a702c8abb2 ("mmc: host: split up sdhci-pxa, create sdhci-pxav3.c")'
Fix this and hopefully prevent it happening in the future by ensuring named
initialisers always follow the declaration order in the structure definition.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Cc: <stable@vger.kernel.org> # v3.16+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This allows us to get rid of the #else condition, as the macro compiles
away to nothing if not enabled.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This allows us to get rid of the #else condition, as the macro compiles
away to nothing if not enabled.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As the code is using SIMPLE_DEV_PM_OPS helper, this compiles away to
nothing if CONFIG_PM_SLEEP is disabled. Thus we don't need to #define
the suspend/resume callbacks to NULL.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As the code is using SIMPLE_DEV_PM_OPS helper, this compiles away to
nothing if CONFIG_PM_SLEEP is disabled. Thus we don't need to #define
the suspend/resume callbacks to NULL.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch removes the superflous .owner field for drivers which
use the module_platform_driver API, as this is overriden in
platform_driver_register anyway.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
781e989cf5 ("mmc: sdhci: convert to new SDIO IRQ handling") and
bf3b5ec66b ("mmc: sdio_irq: rework sdio irq handling") disabled
the use of our own custom threaded IRQ handler, but left in an
unconditional wake_up_process() on that handler at resume-time.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=80151
In addition, the check for MMC_CAP_SDIO_IRQ capability is added
before enable sdio IRQ.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <chris@printf.net>
Signed-off-by: Fu Zhonghui <zhonghui.fu@linux.intel.com>
Cc: <stable@vger.kernel.org> # v3.16+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There are upcoming MIPS SoCs with dw_mmc hosts.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The dw_mmc drivers rely on the DMA API, so update the Kconfig entry
to depend on HAS_DMA. Since the drivers should build on any platform
with DMA, allow the driver to compile tested on non-ARC/ARM platforms.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
when SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK is set, timeout_clk is sdclk.
We need to update it when we change sdclk in sdhci_set_clock.
This allow to have a more precisse timeout and max_busy_timeout. This
can help for command that need a big busy wait (erase, ...).
Signed-off-by: Matthieu CASTET <matthieu.castet@parrot.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When we wait for busy after sending a command, if there is
a timeout, we got SDHCI_INT_DATA_TIMEOUT flags.
Before this commit we got the message :
"Got data interrupt 0x00100000 even though no data operation was in progress."
and we need to wait 10s that sdhci_timeout_timer expires.
Signed-off-by: Matthieu CASTET <matthieu.castet@parrot.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current code erroneously fill the last byte of R2 response with an undefined
value. In addition, the controller actually 'offloads' the last byte
(CRC7, end bit) while receiving R2 response and thus it's impossible to get the
actual value. This could cause mmc stack to obtain inconsistent CID from the
same card after resume and misidentify it as a different card.
Fix by assigning dummy CRC and end bit: {7'b0, 1} = 0x1 to the last byte of R2.
Cc: <stable@vger.kernel.org> # v3.16+
Fixes: c7f6558d84 ("mmc: Add realtek USB sdmmc host driver")
Signed-off-by: Roger Tseng <rogerable@realtek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current code erroneously fill the last byte of R2 response with an undefined
value. In addition, the controller actually 'offloads' the last byte
(CRC7, end bit) while receiving R2 response and thus it's impossible to get the
actual value. This could cause mmc stack to obtain inconsistent CID from the
same card after resume and misidentify it as a different card.
Fix by assigning dummy CRC and end bit: {7'b0, 1} = 0x1 to the last byte of R2.
Cc: <stable@vger.kernel.org> # v3.8+
Fixes: ff984e57d3 ("mmc: Add realtek pcie sdmmc host driver")
Signed-off-by: Roger Tseng <rogerable@realtek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If we happened to get a data error at just the wrong time the dw_mmc
driver could get into a state where it would never complete its
request. That would leave the caller just hanging there.
We fix this two ways and both of the two fixes on their own appear to
fix the problems we've seen:
1. Fix a race in the tasklet where the interrupt setting the data
error happens _just after_ we check for it, then we get a
EVENT_XFER_COMPLETE. We fix this by repeating a bit of code.
2. Fix it so that if we detect that we've got an error in the "data
busy" state and we're not going to do anything else we end the
request and unblock anyone waiting.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@gmail.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
curr should use signed type since it will contain the returned
value which is possible to be a negative value. Using u32 will
make the returned value to be true even there is a negative result.
Change to use int instead of u32
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Make use of the MMC asynchronous request capability to prepare the
next DMA transfer request in parallel with the current transfer.
This is done by adding pre-request and post-request callbacks that are
used by the MMC framework during an active data transfer.
It should help reduce the impact of DMA preparation overhead on the SD
card performance.
Signed-off-by: Apelete Seketeli <apelete@seketeli.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Until now the MMC driver for JZ4740 SoC was relying on PIO mode only
for data transfers.
This patch allows the use of DMA for data trasnfers in addition to PIO
mode by relying on DMA Engine.
DMA tranfers performance might be further improved by taking advantage
of the asynchronous request capability of the MMC framework.
Signed-off-by: Apelete Seketeli <apelete@seketeli.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch focuses on clock setting for RK3288 mmc controller.
In RK3288 mmc controller, CLKDIV register can only be set 0 or 1,
and if DDR 8bit mode, CLKDIV register must be set 1.
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The code selecting a device for the sdhci host has been
continuously tweaked (4b711cb138
"mmc: sdhci-pltfm: Add structure for host-specific data" and
a4d2177f00 "mmc: sdhci-pltfm: dt
device does not pass parent to sdhci_alloc_host" while there
does not seem to be any reason to use platform device's parent
in the first place.
The comment saying "Some PCI-based MFD need the parent here"
seem to refer to Timberdale FPGA driver (the only MFD driver
registering SDHCI cell, drivers/mfd/timberdale.c) but again,
the only situation when parent device matter is runtime PM,
which is not implemented for Timberdale.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is no need for regulator consumers to include special logic for
fixed voltage regulators as they support regulator_set_voltage() just
like their non-fixed regulator counterparts.
Signed-off-by: Tim Kryger <tim.kryger@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On Qualcomm APQ8064 SOCs, SD card controller has an additional glue
called DML (Data Mover Local/Lite) to assist dma transfers.
This hardware needs to be setup before any dma transfer is requested.
DML itself is not a DMA engine, its just a gule between the SD card
controller and dma controller.
Most of this code has been ported from qualcomm's 3.4 kernel.
This patch adds the code necessary to intialize the hardware and setup
before doing any dma transfers.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Miscellaneous
- Remove DEFINE_PCI_DEVICE_TABLE macro use (Benoit Taine)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jJGu
-----END PGP SIGNATURE-----
Merge tag 'pci-v3.17-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull DEFINE_PCI_DEVICE_TABLE removal from Bjorn Helgaas:
"Part two of the PCI changes for v3.17:
- Remove DEFINE_PCI_DEVICE_TABLE macro use (Benoit Taine)
It's a mechanical change that removes uses of the
DEFINE_PCI_DEVICE_TABLE macro. I waited until later in the merge
window to reduce conflicts, but it's possible you'll still see a few"
* tag 'pci-v3.17-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Remove DEFINE_PCI_DEVICE_TABLE macro use
- Forward compatibility for eMMC.
- Fix some blacklisted cards with broken secure discard.
MMC host:
- mmci: Add support for Qualcomm variant.
- mmci: Fix regression for arm_variant.
- sdhci: Various fixes and cleanups.
- sdhci: Improve external VDD regulator support.
- sdhci: Support for DDR50 1.8V mode for BayTrail.
- sdhci-st: Add driver for ST SDHCI controller.
- sh-mmcif: DMA fixes.
- omap_hsmmc: Add support for SDIO interrupts.
- sdhci-pci: Add support for Intel Quark X1000.
- dw_mmc: Update the reset sequence.
- s3cmci: port DMA code to dmaengine API.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=kGSY
-----END PGP SIGNATURE-----
Merge tag 'mmc-v3.17-1' of git://git.linaro.org/people/ulf.hansson/mmc
Pull MMC updates from Ulf Hansson:
"Me and Chris Ball decided to try out using my MMC tree as the primary
one, to simplify handling of patches.
This pull does thus contains all the MMC patches for 3.17 rc1, no pull
from Chris this time.
Details:
MMC core:
- forward compatibility for eMMC
- fix some blacklisted cards with broken secure discard
MMC host:
- mmci: Add support for Qualcomm variant
- mmci: Fix regression for arm_variant
- sdhci: Various fixes and cleanups
- sdhci: Improve external VDD regulator support
- sdhci: Support for DDR50 1.8V mode for BayTrail
- sdhci-st: Add driver for ST SDHCI controller
- sh-mmcif: DMA fixes
- omap_hsmmc: Add support for SDIO interrupts
- sdhci-pci: Add support for Intel Quark X1000
- dw_mmc: Update the reset sequence
- s3cmci: port DMA code to dmaengine API"
* tag 'mmc-v3.17-1' of git://git.linaro.org/people/ulf.hansson/mmc: (67 commits)
mmc: dw_mmc: modify the dt-binding for removing slot-node and supports-highspeed
mmc: dw_mmc: Slot quirk "disable-wp" is deprecated.
mmc: mmci: Reverse IRQ handling for the arm_variant
mmc: mmci: Move all CMD irq handling to mmci_cmd_irq()
mmc: mmci: Remove redundant check of status for DATA irq
mmc: dw_mmc: change to use recommended reset procedure
mmc: sdhci-pxav3: Use devm_* managed helpers
mmc: tmio: Configure DMA slave bus width
mmc: sh_mmcif: Configure DMA slave bus width
mmc: sh_mmcif: Fix DMA slave address configuration
mmc: sh_mmcif: Document DT bindings
mmc: sdhci-pci: remove PCI PM functions in suspend/resume callback
mmc: Do not advertise secure discard if it is blacklisted
mmc: sdhci-msm: Get COMPILE_TEST support
mmc: sdhci-msm: Remove unnecessary header file inclusion
mmc: sdhci-msm: Fix the binding example
mmc: sdhci: add DDR50 1.8V mode support for BayTrail eMMC Controller
mmc: sdhci: Preset value not supported in Baytrail eMMC
mmc: MMC_USDHI6ROL0 should depend on HAS_DMA
mmc: MMC_SH_MMCIF should depend on HAS_DMA
...
We should prefer `struct pci_device_id` over `DEFINE_PCI_DEVICE_TABLE` to
meet kernel coding style guidelines. This issue was reported by checkpatch.
A simplified version of the semantic patch that makes this change is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@@
identifier i;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer z;
@@
- DEFINE_PCI_DEVICE_TABLE(i)
+ const struct pci_device_id i[]
= z;
// </smpl>
[bhelgaas: add semantic patch]
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Commit "mmc: mmci: Handle CMD irq before DATA irq", caused an issue
when using the ARM model of the PL181 and running QEMU.
The bug was reported for the following QEMU version:
$ qemu-system-arm -version
QEMU emulator version 2.0.0 (Debian 2.0.0+dfsg-2ubuntu1.1), Copyright
(c) 2003-2008 Fabrice Bellard
To resolve the problem, let's restore the old behavior were the DATA
irq is handled prior the CMD irq, but only for the arm_variant, which
the problem was reported for.
Reported-by: John Stultz <john.stultz@linaro.org>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Russell King <linux@arm.linux.org.uk>
Tested-by: Kees Cook <keescook@chromium.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ulf Hansson