The PCI core provides a generic pcibios_setup() routine. Drop this
architecture-specific version in favor of that.
Tested-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
sh_clk_mstp32_register is deprecated. This convert to sh_clk_mstp_register.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* topic/sebastian-devinit-fixups:
scripts/modpost: check for bad references in .pci.fixups area
sh/PCI: move fixup hooks from __init to __devinit
powerpc/PCI: move fixup hooks from __init to __devinit
frv/PCI: move fixup hooks from __init to __devinit
arm/PCI: move fixup hooks from __init to __devinit
alpha/PCI: move fixup hooks from __init to __devinit
PCI: move fixup hooks from __init to __devinit
x86/PCI: move fixup hooks from __init to __devinit
The fixups are executed once the pci-device is found which is during
boot process so __init seems fine as long as the platform does not
support hotplug.
However it is possible to remove the PCI bus at run time and have it
rediscovered again via "echo 1 > /sys/bus/pci/rescan" and this will call
the fixups again.
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Replace the struct pci_bus secondary/subordinate members with the
struct resource busn_res. Later we'll build a resource tree of these
bus numbers.
[bhelgaas: changelog]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Attempt to "tidy" up some of the multi IRQ handling and base + IRQ
management. This should keep it limping along without too much hassle,
and no new parts should ever be enabling or using this API anyways.
It doesn't get any closer to lipstick on a pig as this.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
We don't support the ISA DMA API, so this is only ever misused. The
dma-sh case inadvertently broke the dreamcast case by testing the wrong
variable for the total number of channels, so this fixes that up too.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
If in big-endian mode, switch the PCI bus, too.
Tested on both litte-endian and big-endian sh7785lcr.
Signed-off-by: Thomas Schwinge <thomas@codesourcery.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: linux-sh@vger.kernel.org
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Pull PCI changes (including maintainer change) from Jesse Barnes:
"This pull has some good cleanups from Bjorn and Yinghai, as well as
some more code from Yinghai to better handle resource re-allocation
when enabled.
There's also a new initcall_debug feature from Arjan which will print
out quirk timing information to help identify slow quirks for fixing
or refinement (Yinghai sent in a few patches to do just that once the
new debug code landed).
Beyond that, I'm handing off PCI maintainership to Bjorn Helgaas.
He's been a core PCI and Linux contributor for some time now, and has
kindly volunteered to take over. I just don't feel I have the time
for PCI review and work that it deserves lately (I've taken on some
other projects), and haven't been as responsive lately as I'd like, so
I approached Bjorn asking if he'd like to manage things. He's going
to give it a try, and I'm confident he'll do at least as well as I
have in keeping the tree managed, patches flowing, and keeping things
stable."
Fix up some fairly trivial conflicts due to other cleanups (mips device
resource fixup cleanups clashing with list handling cleanup, ppc iseries
removal clashing with pci_probe_only cleanup etc)
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci: (112 commits)
PCI: Bjorn gets PCI hotplug too
PCI: hand PCI maintenance over to Bjorn Helgaas
unicore32/PCI: move <asm-generic/pci-bridge.h> include to asm/pci.h
sparc/PCI: convert devtree and arch-probed bus addresses to resource
powerpc/PCI: allow reallocation on PA Semi
powerpc/PCI: convert devtree bus addresses to resource
powerpc/PCI: compute I/O space bus-to-resource offset consistently
arm/PCI: don't export pci_flags
PCI: fix bridge I/O window bus-to-resource conversion
x86/PCI: add spinlock held check to 'pcibios_fwaddrmap_lookup()'
PCI / PCIe: Introduce command line option to disable ARI
PCI: make acpihp use __pci_remove_bus_device instead
PCI: export __pci_remove_bus_device
PCI: Rename pci_remove_behind_bridge to pci_stop_and_remove_behind_bridge
PCI: Rename pci_remove_bus_device to pci_stop_and_remove_bus_device
PCI: print out PCI device info along with duration
PCI: Move "pci reassigndev resource alignment" out of quirks.c
PCI: Use class for quirk for usb host controller fixup
PCI: Use class for quirk for ti816x class fixup
PCI: Use class for quirk for intel e100 interrupt fixup
...
Convert calls to free_irq so that the second argument is the same as the
last argument of the corresponding call to request_irq. Without this
property, free_irq does nothing.
In the case of dmabrg.c the change is merely cosmetic - changing 0 to NULL.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.15 (GNU/Linux)
iEYEABECAAYFAk9HE98ACgkQGkmNcg7/o7g4+QCfYIcWunicH7+tLMjH/h5MgHq2
S5EAoJdIKyAPfV1tsIY0ykJZQP+H4t4X
=QqTI
-----END PGP SIGNATURE-----
Merge tag 'sh-for-linus' of git://github.com/pmundt/linux-sh
SuperH fixes for 3.3-rc5
* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh:
sh: Fix sh2a build error for CONFIG_CACHE_WRITETHROUGH
sh: modify a resource of sh_eth_giga1_resources in board-sh7757lcr
arch/sh: remove references to cpu_*_map.
sh: Fix typo in pci-sh7780.c
sh: add platform_device for SPI1 in setup-sh7757
sh: modify resource for SPI0 in setup-sh7757
sh: se7724: fix compile breakage
sh: clkfwk: bugfix: use clk_reparent() for div6 clocks
sh: clock-sh7724: fixup sh_fsi clock settings
sh: sh7757lcr: update to the new MMCIF DMA configuration
sh: fix the sh_mmcif_plat_data in board-sh7757lcr
video: pvr2fb: Fix up spurious section mismatch warnings.
sh: Defer to asm-generic/device.h.
Correct spelling "erorr" to "error" in
arch/sh/drivers/pci/pci-sh7780.c
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Tell the PCI core about host bridge address translation so it can take
care of bus-to-resource conversion for us.
CC: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
commit 43db595e8b
(sh: switch to GENERIC_PCI_IOMAP)
failed to take into account the PCI channels's
io_map_base for mapping IO BARs.
This also caused a new warning on sh.
Fix this, without re-introducing code duplication,
by setting NO_GENERIC_PCI_IOPORT_MAP
and supplying a sh-specific __pci_ioport_map.
Reported-by: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci: (80 commits)
x86/PCI: Expand the x86_msi_ops to have a restore MSIs.
PCI: Increase resource array mask bit size in pcim_iomap_regions()
PCI: DEVICE_COUNT_RESOURCE should be equal to PCI_NUM_RESOURCES
PCI: pci_ids: add device ids for STA2X11 device (aka ConneXT)
PNP: work around Dell 1536/1546 BIOS MMCONFIG bug that breaks USB
x86/PCI: amd: factor out MMCONFIG discovery
PCI: Enable ATS at the device state restore
PCI: msi: fix imbalanced refcount of msi irq sysfs objects
PCI: kconfig: English typo in pci/pcie/Kconfig
PCI/PM/Runtime: make PCI traces quieter
PCI: remove pci_create_bus()
xtensa/PCI: convert to pci_scan_root_bus() for correct root bus resources
x86/PCI: convert to pci_create_root_bus() and pci_scan_root_bus()
x86/PCI: use pci_scan_bus() instead of pci_scan_bus_parented()
x86/PCI: read Broadcom CNB20LE host bridge info before PCI scan
sparc32, leon/PCI: convert to pci_scan_root_bus() for correct root bus resources
sparc/PCI: convert to pci_create_root_bus()
sh/PCI: convert to pci_scan_root_bus() for correct root bus resources
powerpc/PCI: convert to pci_create_root_bus()
powerpc/PCI: split PHB part out of pcibios_map_io_space()
...
Fix up conflicts in drivers/pci/msi.c and include/linux/pci_regs.h due
to the same patches being applied in other branches.
Many architectures don't want to pull in iomap.c,
so they ended up duplicating pci_iomap from that file.
That function isn't trivial, and we are going to modify it
https://lkml.org/lkml/2011/11/14/183
so the duplication hurts.
This reduces the scope of the problem significantly,
by moving pci_iomap to a separate file and
referencing that from all architectures.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJPBZXBAAoJECgfDbjSjVRpuuYIAIMD0wE96MuTOSBJX4VG8VAP
UyjL9dsfMRy8CKioQo5/fxpTY07YBCWmNauSSX7pzgcoUKBfYIGn4Z1qwGYsWK9M
CzLs6PXLTugw0FtKobHZl/klRTWEBS6YOUjp9x568rplwF+Ppk7b993uj7eS/g+e
T0mUKzqg4/UavbHd9+W5KgC4drQ5hgtu2WZHoUxBK4umnd3C2G+U82Sthg50o/XU
SC8IGm39K8I36HoIWgXj3Y7nkOP3mQELohOT4ZPiVSmLvGS4i47+ix75anO+8ZvZ
jxHr8RC85IK1Nd89NZhbKOyvx0QQiwoKUZaTwcWXJNSOADzZnM6icdIsodc+Elo=
=ccQZ
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
lib: use generic pci_iomap on all architectures
Many architectures don't want to pull in iomap.c,
so they ended up duplicating pci_iomap from that file.
That function isn't trivial, and we are going to modify it
https://lkml.org/lkml/2011/11/14/183
so the duplication hurts.
This reduces the scope of the problem significantly,
by moving pci_iomap to a separate file and
referencing that from all architectures.
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
alpha: drop pci_iomap/pci_iounmap from pci-noop.c
mn10300: switch to GENERIC_PCI_IOMAP
mn10300: add missing __iomap markers
frv: switch to GENERIC_PCI_IOMAP
tile: switch to GENERIC_PCI_IOMAP
tile: don't panic on iomap
sparc: switch to GENERIC_PCI_IOMAP
sh: switch to GENERIC_PCI_IOMAP
powerpc: switch to GENERIC_PCI_IOMAP
parisc: switch to GENERIC_PCI_IOMAP
mips: switch to GENERIC_PCI_IOMAP
microblaze: switch to GENERIC_PCI_IOMAP
arm: switch to GENERIC_PCI_IOMAP
alpha: switch to GENERIC_PCI_IOMAP
lib: add GENERIC_PCI_IOMAP
lib: move GENERIC_IOMAP to lib/Kconfig
Fix up trivial conflicts due to changes nearby in arch/{m68k,score}/Kconfig
Convert from pci_scan_bus() to pci_scan_root_bus() and remove root bus
resource fixups. This fixes the problem of "early" and "header" quirks
seeing incorrect root bus resources.
CC: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The 'latency timer' of PCI devices, both Type 0 and Type 1,
is setup in architecture-specific code [see: 'pcibios_set_master()'].
There are two approaches being taken by all the architectures - check
if the 'latency timer' is currently set between 16 and 255 and if not
bring it within bounds, or, do nothing (and then there is the
gratuitously different PA-RISC implementation).
There is nothing architecture-specific about PCI's 'latency timer' so
this patch pulls its setup functionality up into the PCI core by
creating a generic 'pcibios_set_master()' function using the '__weak'
attribute which can be used by all architectures as a default which,
if necessary, can then be over-ridden by architecture-specific code.
No functional change.
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
After all sysdev classes are ported to regular driver core entities, the
sysdev implementation will be entirely removed from the kernel.
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
sh copied pci_iomap from generic code, probably to avoid
pulling the rest of iomap.c in. Since that's in
a separate file now, we can reuse the common implementation.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
To fix:
arch/sh/drivers/dma/dma-sysfs.c:45:8: error: 'S_IRUGO' undeclared here (not in a function)
arch/sh/drivers/dma/dma-sysfs.c:75:8: error: 'S_IWUSR' undeclared here (not in a function)
make[4]: *** [arch/sh/drivers/dma/dma-sysfs.o] Error 1
drivers/sh/intc/core.c:449: error: 'S_IRUGO' undeclared here (not in a function)
make[5]: *** [drivers/sh/intc/core.o] Error 1
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Since commit [e58aa3d2: genirq: Run irq handlers with interrupts disabled],
We run all interrupt handlers with interrupts disabled
and we even check and yell when an interrupt handler
returns with interrupts enabled (see commit [b738a50a:
genirq: Warn when handler enables interrupts]).
So now this flag is a NOOP and can be removed.
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Aside of the usual motivation for constification, this function has a
history of being abused a hook for interrupt and other fixups so I turned
this function const ages ago in the MIPS code but it should be done
treewide.
Due to function pointer passing in varous places a few other functions
had to be constified as well.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
To: Anton Vorontsov <avorontsov@mvista.com>
To: Chris Metcalf <cmetcalf@tilera.com>
To: Colin Cross <ccross@android.com>
Acked-by: "David S. Miller" <davem@davemloft.net>
To: Eric Miao <eric.y.miao@gmail.com>
To: Erik Gilling <konkers@android.com>
Acked-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
To: "H. Peter Anvin" <hpa@zytor.com>
To: Imre Kaloz <kaloz@openwrt.org>
To: Ingo Molnar <mingo@redhat.com>
To: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
To: Jesse Barnes <jbarnes@virtuousgeek.org>
To: Krzysztof Halasa <khc@pm.waw.pl>
To: Lennert Buytenhek <kernel@wantstofly.org>
To: Matt Turner <mattst88@gmail.com>
To: Nicolas Pitre <nico@fluxnic.net>
To: Olof Johansson <olof@lixom.net>
Acked-by: Paul Mundt <lethal@linux-sh.org>
To: Richard Henderson <rth@twiddle.net>
To: Russell King <linux@arm.linux.org.uk>
To: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-alpha@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-pci@vger.kernel.org
Cc: linux-sh@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Cc: sparclinux@vger.kernel.org
Cc: x86@kernel.org
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
For the SMP case we run in to a lockup without a full synchronization
prior to continuing with the boot.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SH-X3 controllers all have pretty dire delays needed for PHY wakeup, so
we attempt to mitigate the damage by bringing them up asynchronously,
simply using the synchronization points for persistent bridge to channel
numbering.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'for-2.6.38' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (33 commits)
usb: don't use flush_scheduled_work()
speedtch: don't abuse struct delayed_work
media/video: don't use flush_scheduled_work()
media/video: explicitly flush request_module work
ioc4: use static work_struct for ioc4_load_modules()
init: don't call flush_scheduled_work() from do_initcalls()
s390: don't use flush_scheduled_work()
rtc: don't use flush_scheduled_work()
mmc: update workqueue usages
mfd: update workqueue usages
dvb: don't use flush_scheduled_work()
leds-wm8350: don't use flush_scheduled_work()
mISDN: don't use flush_scheduled_work()
macintosh/ams: don't use flush_scheduled_work()
vmwgfx: don't use flush_scheduled_work()
tpm: don't use flush_scheduled_work()
sonypi: don't use flush_scheduled_work()
hvsi: don't use flush_scheduled_work()
xen: don't use flush_scheduled_work()
gdrom: don't use flush_scheduled_work()
...
Fixed up trivial conflict in drivers/media/video/bt8xx/bttv-input.c
as per Tejun.
flush_scheduled_work() is deprecated and scheduled to be removed.
Directly flush psw->work on removal instead.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: linux-sh@vger.kernel.org
This takes a bit of a sledgehammer to the machvec I/O routines. The
iomem case requires no special casing and so can just be dropped
outright. This only leaves the ioport casing for PCI and SuperIO
mangling. With the SuperIO case going through the standard ioport
mapping, it's possible to replace everything with generic routines.
With this done the standard I/O routines are tidied up and NO_IOPORT
now gets default-enabled for the vast majority of boards.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The SDK7786 FPGA has secondary control over the PCIe clocks, specifically
relating to the slots and oscillator. This ties the FPGA clocks in to the
clock framework and balances the refcounting similar to how the primary
on-chip clocks are managed. While the on-chip clocks are per-port, the
FPGA clock enable/disable is global for the entire block.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SDK7786 supports connecting either slot3 or 4 to the same PCIe port by
way of FPGA muxing. By default the vertical slot 3 on the baseboard is
enabled, so this adds in a command line option for forcibly enabling the
slot 4 edge connector.
If nothing has been specified on the command line, we fall back to
reading the resistor values for card presence to figure out where to
route the port to.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This copies the pci_config_lock idea from x86 over, allowing us to kill
off a couple of existing private locks. At the same time, these need to
be converted to raw spinlocks for -rt kernels, so we make that change at
the same time. This should make it easier for future parts to get the
locking right instead of inevitable ending up with lock type mismatches.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This gets each port handling its MSTP bit, as well as moving the PHY
clock management in to the clock framework.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Some of the existing code is flipping between __raw_xxx() and
pci_{read,write}_reg(). As the latter are just wrappers for the former,
flip over to using them consistently.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently we error out if a link is disabled and simply drop the port
registration outright. This follows the PPC changes and simply reports on
the link state on boot, leaving the port registered, in order to more
easily deal with hotplug on future parts.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
These settings are properly propagated by the hardware already, so
there's no need to bother with them manually.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The SH7786 PCIe is presently unable to enumerate itself in root complex
mode, and has no visibility through either type 0 or type 1 accesses,
despite having a mostly sensible extended config space for each port.
Attempts to generate type 0 or type 1 config cycles result in completer
aborts, so we're ultimately forced to use SuperHyway transactions
instead.
As each port has a single port <-> device mapping that resolves for any
PCI_SLOT definition, we simply hijack devfn 0 for the SuperHyway
transaction and bump up the devfn limit.
With enumeration of the root complex now possible, we also need to insert
an early fixup to hide the BARs from the kernel. With all of that done,
it's now possible to use the pcieport services with all of the PCIe
ports, which is the first step to power management support.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Previously these IDs were only used by one driver, so there was not much
need for having them generically defined. Now that this will no longer
hold true, move them over.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The spec suggests waiting up to 500ms for the PHY to settle before
testing link state, but practice shows that 100ms is sufficient (this is
the delay value we also use on the other SH-4A PCI controllers, too).
This makes device detection much more reliable, although in the future it
should be a bit faster to simply serialize with a TLP IRQ.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that the resource assignment issues are resolved, we can finally wire
up the small third memory window -- in the future we may reclaim this for
MSI.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
An IORESOURCE_IO was missing here, which meant that we weren't properly
establishing the I/O window for this particular slot. With this
corrected, cards with I/O BARs have them actually assigned and
accessible.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Certain memory windows are only available for 32-bit space, so skip over
these in 29-bit mode. This will severely restrict the amount of memory
that can be mapped, but since a boot loader bug makes booting in 29-bit
mode close to impossible anyways, everything is ok.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This bumps up the low address to match the physical memory windows for
SHway<->PCIe transfers. The previous implementation was banking on a 1:1
virt<->phys SHway mapping, which doesn't apply here.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SH7786 PCIe has 1 slot per port, but no specific restriction on function.
Relax the devfn restriction and look to the slot number instead when
configured as a root complex.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This brings the clocking and register setting in line with the somewhat
factually ambiguous specification.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This enables support for type 1 config space accesses on the SH7786
PCI controller. At the same time, add in some extra sanity checks for
controller asserted errors.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
create_proc_read_entry() may fail, if so return -ENOMEM.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This typo seems to have been copy and pasted in the PCI initialization
code. Replace 'intialization' with 'initialization'.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
pcibios_fixup_device_resources() presently skips over resources flagged
with IORESOURCE_PCI_FIXED, which is a remnant of the old PCI-auto code.
The only user for this at present is the Dreamast GAPSPCI code which
can't tolerate any adjustments to the BARs, but a combination of the
IORESOURCE_PCI_FIXED and zeroed out hose offsets does the right thing for
this case already, so we simply kill off the special casing.
Reported-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the sh7751 pci code to handle io ports
correctly. The code is based on the sh7788x implementation.
Tested on a R2D-1 board with CONFIG_8139TOO_PIO=y.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (187 commits)
sh: remove dead LED code for migo-r and ms7724se
sh: ecovec build fix for CONFIG_I2C=n
sh: ecovec r-standby support
sh: ms7724se r-standby support
sh: SH-Mobile R-standby register save/restore
clocksource: Fix up a registration/IRQ race in the sh drivers.
sh: ms7724: modify scan_timing for KEYSC
sh: ms7724: Add sh_sir support
sh: mach-ecovec24: Add sh_sir support
sh: wire up SET/GET_UNALIGN_CTL.
sh: allow alignment fault mode to be configured at kernel boot.
sh: sh7724: Update FSI/SPU2 clock
sh: always enable sh7724 vpu_clk and set to 166MHz on Ecovec
sh: add sh7724 kick callback to clk_div4_table
sh: introduce struct clk_div4_table
sh: clock-cpg div4 set_rate() shift fix
sh: Turn on speculative return for SH7785 and SH7786
sh: Merge legacy and dynamic PMB modes.
sh: Use uncached I/O helpers in PMB setup.
sh: Provide uncached I/O helpers.
...
Now that we return the new resource start position, there is no
need to update "struct resource" inside the align function.
Therefore, mark the struct resource as const.
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
As suggested by Linus, align functions should return the start
of a resource, not void. An update of "res->start" is no longer
necessary.
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This reworks some of the SH7786 PCIe initialization code to dynamically
setup and size the various resource windows, as opposed to the original
code that simply wired in a couple of them statically.
At the same time, we tidy up the initialization code a bit, kill off some
read-only register twiddling that was gleaned from the bus analyzer, and
also propagate the physical slot/channel mapping.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds in some of the missing memory resources for channels 1/2 and
gets the code building again for the recent changes.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Both the original arch/sh/drivers/dma/dma-sh.c and the new SH dmaengine drivers
do not take into account bits 3:2 of the Transfer Size field in the CHCR
register, besides, bit-field defines set bit 2, but the mask only passes bits
1:0 through. TS_16BLK and TS_32BLK macros are bogus too. This patch fixes all
these issues for sh7722 and sh7724, other CPUs stay unchanged and might need to
be fixed too.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for handling early PERR/SERR triggering in between
controller registration and the initial bus scan. Buggy cards end up
asserting these as soon as the M66EN scan is undertaken, resulting in
an early crash.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The SH7780 PCI controller supports 3 different ranges of PCI memory in
addition to its PCI I/O window. In the case of 29-bit mode, only 2 memory
windows are supported, while in 32-bit mode all 3 are visible. This
attempts to make the resource handling completely dynamic and to permit
platforms to map in as many apertures as they can handle.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
These were never handled before, so implement some common infrastructure
to support them, then make use of that in the SH7780-specific code. In
practice there is little here that can not be generalized for SH4 parts,
which will be an incremental change as the 7780/7751 code is gradually
unified.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
register_pci_controller() can fail, but presently is a void function.
Change this over to an int so that we can bail early before continuing on
with post-registration initialization (such as throwing the controller in
to 66MHz mode in the case of the SH7780 host controller).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds some helper glue for scanning the bus and determining if all
of the devices are 66MHz capable or not before flipping on 66MHz mode.
This isn't quite to spec, but it's fairly consistent with what other
embedded controllers end up having to do.
Scanning code cribbed from the MIPS txx9 PCI code.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
For systems that have more than 512MB we need to set up an additional
mapping, this fixes up the rounding to the next power of two and splits
out the mapping accordingly between the two local bus mapping windows.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The host controllers only support type 1, so there's not much else to
test for. Some of the older controllers also supported type 2 accesses,
but we've never supported those, and likely never will. Beyond that, the
P1SEG test is meaningless for 32-bit mode, so rather than refactoring it,
just kill the type 1 test off completely.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Newer SH parts are now commonly shipping with multiple controllers, so
we wire up PCI domain support to deal with them. Shamelessly cloned from
the MIPS implementation.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently we just call in to request_resource() for the ioport and iomem
resources without checking for errors. This has already hidden a couple
of bugs, so add some error handling in for good measure.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This consolidates the PCI initialization code for all of the pci-sh7780
users, and sets up the memory window dynamically as opposed to using
hardcoded window positions.
A number of bugs were fixed at the same time, including the PIO handling
and master abort timeout settings being incorrect.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The old ctrl in/out routines are non-portable and unsuitable for
cross-platform use. While drivers/sh has already been sanitized, there
is still quite a lot of code that is not. This converts the arch/sh/ bits
over, which permits us to flag the routines as deprecated whilst still
building with -Werror for the architecture code, and to ensure that
future users are not added.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Previously this was only built in for Urquell boards, but the same
approach can be used on SDK7786 now that the mode pin reading is
supported, so make it generic to SH7786.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This permits the resource access size to be handed off through the
resource flags, which saves platforms from having to establish
platform data only to specify the register width.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Michal Marek <mmarek@suse.cz>
This is a static symbol, so the export is wholly superfluous. Recent
kbuild updates flagged this as an error, resulting in build failure,
so this tidies that up.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that this contains a grand total of 1 Kconfig option, it's hardly
worth keeping split out. Roll CONFIG_PCI back in to the top-level
architecture Kconfig, along with the other bus types.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Leaving this configurable caused more trouble than it was ever worth, so
just make it explicit. Boards that are verified one way or the other can
fix up their selects accordingly. We presently default to non-coherent
for most platforms.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This supported all DMA channels, and it was tested in SH7722,
SH7780, SH7785 and SH7763.
This can not use with SH DMA API.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Reviewed-by: Matt Fleming <matt@console-pimps.org>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The synopsys PCI cell used in the later STMicro chips requires code to
be run in order to do IO cycles, rather than just memory mapping the IO
space. Rather than extending the existing SH infrastructure to allow
this, use the GENERIC_IOMAP implmentation to save re-inventing the
wheel.
This set of changes allows the SH to be built with GENERIC_IOMAP
enabled, it just ifdef's out the functions provided by the GENERIC_IOMAP
implementation, and provides a few required missing functions.
Signed-off-by: David McKay <david.mckay@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
While most platforms implement LED banks in sets of 8/16/32, some use
different configurations. This adds a LED mask to the heartbeat platform
data to allow platforms to constrain the bitmap, which is otherwise
derived from the register size.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds initial support for the PCI-Express module in the SH7786,
particularly as it relates to the urquell platform. Presently it is
only supported in root complex mode, with endpoint mode still requiring
more debugging. 29/32-bit mode and lane configurations are selectable via
board mode pins, and are otherwise fixed.
Only 4x and 1x PCI channels are presently handled, the PCI bridge still
requires additional debugging and stabilization in hardware.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds in preliminary support for the SH7786 PCIe module PCI ops,
and the corresponding module definitions.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Myron Stowe