Fix the following compile warning:
arch/arm/mach-omap2/clkt_clksel.c: In function '_get_div_and_fieldval':
arch/arm/mach-omap2/clkt_clksel.c💯35: warning: 'max_clkr' may be
used uninitialized in this function
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds support for low level debugging on TI816X boards. Currently the
support for UART3 console on TI816X EVM is added.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds minimal support and build configuration for TI816X EVM.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch updates the common machine specific source files with support for
TI816X.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch updates the common platform files with TI816X support.
The approach taken in this patch is to add TI816X as part of OMAP3 variant where
the cpu class is considered as OMAP34XX and the type is TI816X. This means, both
cpu_is_omap34xx() and cpu_is_ti816x() checks return success on TI816X.
A kernel config option CONFIG_SOC_OMAPTI816X is added under OMAP3 to include
support for TI816X build.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Fix text_poke_smp_batch() deadlock
perf tools: Fix thread_map event synthesizing in top and record
watchdog, nmi: Lower the severity of error messages
ARM: oprofile: Fix backtraces in timer mode
oprofile: Fix usage of CONFIG_HW_PERF_EVENTS for oprofile_perf_init and friends
The new init_early hook happens at the end of setup_arch,
which is too early for kzalloc. However, there's no need
to call omap_serial_early_init that early, so fix this
by setting it up as a core_initcall.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Move non-mapping and non-irq initialization code out of .map_io and
.init_irq respectively into the new init_early hook.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some macros defined in mcbsp.h related to audio, which are never being used
is removed.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Charulatha V <charu@ti.com>
Cc: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: G, Manjunath Kondaiah <manjugk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6657/1: hw_breakpoint: fix ptrace breakpoint advertising on unsupported arch
ARM: 6656/1: hw_breakpoint: avoid UNPREDICTABLE behaviour when reading DBGDSCR
ARM: 6658/1: collie: do actually pass locomo_info to locomo driver
ARM: 6659/1: Thumb-2: Make CONFIG_OABI_COMPAT depend on !CONFIG_THUMB2_KERNEL
ARM: 6654/1: perf/oprofile: fix off-by-one in stack check
ARM: fixup SMP alternatives in modules
ARM: make SWP emulation explicit on !CPU_USE_DOMAINS
ARM: Avoid building unsafe kernels on OMAP2 and MX3
ARM: pxa: Properly configure PWM period for palm27x
ARM: pxa: only save/restore registers when pm functions are defined
ARM: pxa/colibri: use correct SD detect pin
ARM: pxa: fix mfpr_sync to read from valid offset
The pointer math in omap_mbox_get() is not quite right, and leads to
passing NULL to strcmp() when searching for an mbox that is not first
in the list.
Convert to using array indexing as is done in all the other functions
which walk the mbox list.
Tested on OMAP2420/n810, OMAP3630/zoom3, OMAP4430/Blaze
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The IRQ numbering for the IVA and DSP mailboxes was switched due
to the wrong ordering in the OMAP2 mbox list. Switch the ordering
so DSP is first and matches all the other SoCs.
Tested on OMAP2420/n810.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The ptrace debug information register was advertising breakpoint and
watchpoint resources for unsupported debug architectures. This meant
that setting breakpoints on these architectures would appear to succeed,
although they would never fire in reality.
This patch fixes the breakpoint slot probing so that it returns 0 when
running on an unsupported debug architecture.
Reported-by: Ulrich Weigand <ulrich.weigand@de.ibm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reading baseline CP14 registers, other than DBGDIDR, when the OS Lock
is set leads to UNPREDICTABLE behaviour.
This patch ensures that we clear the OS lock before accessing anything
other than the DBGDIDR, thereby avoiding this behaviour.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
locomo_info isn't actually used as a platform_data on collie platform:
arm/mach-sa1100/collie.c:237: warning: ‘locomo_info’ defined but not used
So locomo driver doesn't setup IRQs correctly. Pass locomo_info to the
driver.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
rmk says: "You might as well make OABI_COMPAT depend on !THUMB2_KERNEL.
OABI userland is useless without FPA support."
nwfpe doesn't work with Thumb-2 anyway and will probably never get
ported, so I can't argue with that.
This patch implements the dependency change.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Previously we were relying on it being pulled in by other headers for
the prototype of s3c24xx_irq_suspend() and s3c24xx_irq_resume().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch cleans following up.
- Moved definition of System MMU IPNUM into mach/sysmmu.h
- Removed useless SYSMMU_DEBUG configuration
- Removed useless header file plat/sysmmu.h
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The 's5pv310_device_sysmmu' is used on SMDKV310. But since it is not
compiled now, there is a build error. To fix this compilation error,
S5PV310_DEV_SYSMMU needs to be selected for SMDKV310 board.
This patch enables System MMU support on SMDKV310.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
[kgene.kim@samsung.com: Adding description]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Since tail is the previous fp - 1, we need to compare the new fp with tail + 1
to ensure that we don't end up passing in the same tail again, in order to
avoid a potential infinite loop in the perf interrupt handler (which has been
observed to occur). A similar fix seems to be needed in the OProfile code.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
With certain configurations, we inline the unlock functions in modules,
which results in SMP alternatives being created in modules. We need to
fix those up when loading a module to prevent undefined instruction
faults.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
SWP emulation requires that CPU domain support is disabled in order to
work safely. Make that explicit in the kernel configuration to prevent
illegal configurations being generated.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
after these changes omap1_defconfig and omap2plus_defconfig don't have any
section mismatches any more, making it plausible that the patches earlier
in this series are OK.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This variable is only assigned in __init functions and never used later.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
All callers of these functions live in .init.text, so these can go there,
too. There they must not be exported anymore, this is no problem though,
as all callers are always built-in.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
These are only called from omap_nokia770_init which is in .init.text, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP2 (armv6) and MX3 turn off support for the V6K instructions, which
when they include support for SMP kernels means that the resulting
kernel is unsafe on SMP and can result in corrupted filesystems as we
end up using unsafe bitops.
Re-enable the use of V6K instructions on such kernels, and let such
kernels running on V6 CPUs eat undefined instruction faults which will
be much safer than filesystem corruption. Next merge window we can fix
this properly (as it requires a much bigger set of changes.)
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The use of wrong SD detect pin was introduced by this commit:
ARM: pxa: Push Colibri evalboard MFP into module files
This fixes it.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Since mfpr_mmio_base[0] is not always valid on later SoCs,
fixed mpfr_sync() to read back from valid mfp offset always.
Signed-off-by: Yu Tang <ytang5@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
* master.kernel.org:/home/rmk/linux-2.6-arm:
ALSA: AACI: allow writes to MAINCR to take effect
ARM: Update mach-types
ARM: 6652/1: ep93xx: correct the end address of the AC97 memory resource
ARM: mxs/imx28: remove now unused clock lookup "fec.0"
ARM: mxs: fix clock base address missing
ARM: mxs: acknowledge gpio irq
ARM: mach-imx/mach-mx25_3ds: Fix section type
ARM: imx: Add VPR200 and MX51_3DS entries to uncompress.h
ARM i.MX23: use correct register for setting the rate
ARM i.MX23/28: remove secondary field from struct clk. It's unused
ARM i.MX28: use correct register for setting the rate
ARM i.MX28: fix bit operation
FREQ is a ridiculously short name for a platform-specific macro in a
generic header, and it now conflicts with an enumeration in the
gspca/ov519 driver.
Also delete conditional reference to ixp4xx_get_board_tick_rate()
which is not defined anywhere.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Queues should be empty when released, if not, there is a safety valve.
Make sure the queue is usable after it triggers.
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
The last register is at offset 0xa8 making the resource end to be 0xac - 1
instead of 0xb0 - 1.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Don't allow all users to change timer settings.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Do not create mux debugfs files as world-writable.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Panda uses both twl6030 otg phy(vbus, id) and internal
phy(data lines, DP/DM), so removes usb_nop_xceiv_register to make
twl6030 otg driver working since current otg code only supports
one global transceiver. Otherwise, musb doesn't work without
the remove.
Reviewd-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes bug introduced in revision:
f8e9e98454
omap1: DMA: move LCD related code from plat-omap to mach-omap1
The code introduced by this patch didn't consider any other CPUs but OMAP1510,
which rendered OMAP310 -- which has the same LCD controller -- non-working. Use
cpu_is_omap15xx() instead of cpu_is_omap1510() to squash this issue.
Bug found on Palm Zire 71 hardware.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes a wrongly used lcd enable pin.
The Devkit8000 uses twl4030_ledA configured as output gpio only for
the lcd enable line. twl4030_gpio.1 is used through the generic
gpio functions while ledA is used via low level twl4030 calls.
This patch removes the low level calls and use the generic gpio functions
for initialization and use of ledA. This patch also fixes a bug where the
lcd would not power down when blanking.
Further this patch fixes an indentation issue. The comment line uses
eight whitespace and is replaced with a hard tab.
gpio_request + gpio_direction_output are replaced with gpio_request_one.
The return value of gpio_request_one is used to set the value of the
gpio to -EINVAL when unsuccessful, so that gpio_is_valid can detect the
unsuccessful request. But already successful requested gpios are not freed.
Reported-by: Daniel Morsing <daniel.morsing@gmail.com>
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With the commit 7579025130 (regulator:
Factor out voltage set operation into a separate function) fixed voltage
regulator setup will fail if there are voltage constraints defined. This
made MMC unusable on this board. Fix by just deleting those redundant
constraints.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Reviewed-by: Jarkko Nikula <jhnikula@gmail.com>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit b2878fa (ARM: mx28: update clock and device name for dual fec
support) added only the new lookups without removing the old one.
Cc: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
arch/arm/mach-omap2/dma.c: Convert IS_ERR result to PTR_ERR
arm: omap2: mux: fix compile warning
omap1: Simplify use of omap_irq_flags
omap2+: Fix unused variable warning for omap_irq_base
Allow non-ARM SMP processors to use the SMP_ON_UP feature. CPUs
supporting SMP must have the new CPU ID format, so check for this first.
Then check for ARM11MPCore, which fails the MPIDR check. Lastly check
the MPIDR reports multiprocessing extensions and that the CPU is part of
a multiprocessing system.
Cc: <stable@kernel.org>
Reported-and-Tested-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
These errors were found by cppcheck:
arch/arm/mach-omap2/smartreflex.c:784: error: Possible null pointer dereference: sr_info
arch/arm/mach-omap2/smartreflex.c:799: error: Possible null pointer dereference: sr_info
Both conditional statements are executed when sr_info == NULL,
so accessing sr_info->voltdm would fail.
Cc: Russell King <linux@arm.linux.org.uk>
Cc: linux-omap@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Kevin Hilman <khilman@ti.com>
sr_info was allocated and needs a kfree before returning.
This error was reported by cppcheck:
arch/arm/mach-omap2/smartreflex.c:837: error: Memory leak: sr_info
To: Tony Lindgren <tony@atomide.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: linux-omap@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Acked-by: Shweta Gulati <shweta.gulati@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The temporary string holding the directory name to be created should
be released.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Ensure that the ISA/PCI IO space accessors are properly ordered on
ARMv6+ architectures. These should always be ordered with respect to
all other accesses.
This also fixes __iormb() and __iowmb() not being visible to ioread/
iowrite if a platform defines its own MMIO accessors.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Disable the initrd if the passed address already overlaps the reserved
region. This avoids oopses on Netwinders when NeTTrom tells the kernel
that an initrd is located at mem+4MB, but this overlaps the BSS,
resulting in the kernels in-use BSS being freed.
This should be applied to v2.6.37-stable.
Cc: <stable@kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
0ea1293 (arm: return both physical and virtual addresses from addruart)
changed the way the 'addruart' worked, making it return both the virt
and phys addresses. Unfortunately, for footbridge, these were reversed.
Fix that. Tested on Netwinder.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Eliminates the following sparse warnings:
arch/arm/mach-omap1/board-voiceblue.c:253:6: warning: symbol 'voiceblue_wdt_enable' was not declared. Should it be static?
arch/arm/mach-omap1/board-voiceblue.c:261:6: warning: symbol 'voiceblue_wdt_disable' was not declared. Should it be static?
arch/arm/mach-omap1/board-voiceblue.c:269:6: warning: symbol 'voiceblue_wdt_ping' was not declared. Should it be static?
arch/arm/mach-omap1/board-voiceblue.c:278:6: warning: symbol 'voiceblue_reset' was not declared. Should it be static?
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds a clean method to allow platforms to hook into the reset
code if they require to.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Eliminates the following sparse warning:
arch/arm/mach-omap1/board-h3.c:207:27: warning: symbol 'nand_platdata' was not declared. Should it be static?
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Eliminates the following sparse warnings:
arch/arm/mach-omap1/board-htcherald.c:334:34: warning: symbol 'htcpld_chips' was not declared. Should it be static?
arch/arm/mach-omap1/board-htcherald.c:369:34: warning: symbol 'htcpld_pfdata' was not declared. Should it be static?
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Eliminates the following sparse warning:
arch/arm/mach-omap1/board-innovator.c:368:13: warning: symbol 'innovator_mmc_init' was not declared. Should it be static?
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Eliminates the following sparse warning:
arch/arm/mach-omap1/board-h2.c:205:27: warning: symbol 'h2_nand_platdata' was not declared. Should it be static?
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Eliminates the following sparse warning:
arch/arm/plat-omap/dma.c:137:5: warning: symbol 'omap_dma_in_1510_mode' was not declared. Should it be static?
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix the following compile warning:
arch/arm/mach-omap2/irq.c:64:31: warning: 'intc_context' defined but not
used
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix the following section mismatches:
WARNING: arch/arm/mach-omap1/built-in.o(.data+0x491c): Section mismatch
in reference from the variable fsample_config to the (unknown reference)
.init.data:(unknown)
The variable fsample_config references
the (unknown reference) __initdata (unknown)
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the
variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
WARNING: arch/arm/mach-omap1/built-in.o(.data+0x8f0c): Section mismatch
in reference from the variable ams_delta_config to the (unknown
reference) .init.data:(unknown)
The variable ams_delta_config references
the (unknown reference) __initdata (unknown)
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the
variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
WARNING: arch/arm/mach-omap1/built-in.o(.data+0x93ac): Section mismatch
in reference from the variable ams_delta_camera_device to the (unknown
reference) .init.data:(unknown)
The variable ams_delta_camera_device references
the (unknown reference) __initdata (unknown)
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the
variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
WARNING: vmlinux.o(.data+0x5e94): Section mismatch in reference from the
variable fsample_config to the (unknown reference) .init.data:(unknown)
The variable fsample_config references
the (unknown reference) __initdata (unknown)
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the
variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
WARNING: vmlinux.o(.data+0xa484): Section mismatch in reference from the
variable ams_delta_config to the (unknown reference)
.init.data:(unknown)
The variable ams_delta_config references
the (unknown reference) __initdata (unknown)
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the
variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
WARNING: vmlinux.o(.data+0xa924): Section mismatch in reference from the
variable ams_delta_camera_device to the (unknown reference)
.init.data:(unknown)
The variable ams_delta_camera_device references
the (unknown reference) __initdata (unknown)
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the
variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix the following compile warnings:
arch/arm/mach-omap1/board-innovator.c:165:3: warning: initialization
makes integer from pointer without a cast
arch/arm/mach-omap1/board-perseus2.c:305:3: warning: initialization
makes integer from pointer without a cast
arch/arm/mach-omap1/board-fsample.c:338:3: warning: initialization makes
integer from pointer without a cast
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix the following compile warning:
arch/arm/mach-omap1/board-palmte.c:233:13: warning:
'palmte_headphones_detect' defined but not used
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix the following compile warning:
arch/arm/plat-omap/i2c.c:120:13: warning:
'omap_pm_set_max_mpu_wakeup_lat_compat' defined but not used
arch/arm/plat-omap/i2c.c:125:38: warning: 'omap_i2c_latency'
defined but not used
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We want to have just CONFIG_ARCH_OMAP2, 3 and 4. The rest
are nowadays just subcategories of these.
Search and replace the following:
ARCH_OMAP2420 SOC_OMAP2420
ARCH_OMAP2430 SOC_OMAP2430
ARCH_OMAP3430 SOC_OMAP3430
No functional changes.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Thomas Weber <weber@corscience.de>
Acked-by: Sourav Poddar <sourav.poddar@ti.com>
This code elsewhere returns a negative constant to an indicate an error,
while IS_ERR returns the result of a >= operation.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x;
@@
if (...) { ...
- return IS_ERR(x);
+ return PTR_ERR(x);
}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 8419fdbaf2
(omap2+: Add omap_mux_get_by_name) introduced the following
compile warning:
arch/arm/mach-omap2/mux.c: In function '_omap_mux_get_by_name':
arch/arm/mach-omap2/mux.c:163:17: warning: 'found_mode' may be used
uninitialized in this function
Signed-off-by: Felipe Balbi <balbi@ti.com>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 03a9e51261
(omap1: Use asm_irq_flags for entry-macro.S) added support
for multi-omap builds with addition of the omap_irq_flags.
Commit 9f9605c2ed
(omap2+: Fix unused variable warning for omap_irq_base)
simplified omap2+ entry-macro.S by moving omap_irq_flags
out of entry-macro.S.
Simplify omap1 entry-macro.S in a similar way to keep the
code consistent. Based on a similar earlier patch for omap2+
by Russell King <rmk+kernel@arm.linux.org.uk>.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 5d190c4010
(omap2+: Initialize omap_irq_base for entry-macro.S from
platform code) simplified the handling of omap_irq_base
for multi-omap builds. However, this patch also introduced
a build warning for !MULTI_OMAP2 builds:
arch/arm/mach-omap2/io.c: In function 'omap_irq_base_init':
arch/arm/mach-omap2/io.c:322: warning: unused variable 'omap_irq_base'
Fix this by removing the ifdef. Also simplify things further
by moving omap_irq_base out of entry-macro.S.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
A future patch will export gic_mask_irq and gic_unmask_irq.
Rename the pointers in arch/arm/mach-tegra/irq.c to avoid
a compile error.
Signed-off-by: Colin Cross <ccross@android.com>
Commit 37337a8d5e, "ARM: tegra: irq_data
conversion." missed changing one reference to 'irq' in the function
tegra_gpio_irq_set_type(). This patch fixes the build error.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Lennert Buytenhek <buytenh@secretlab.ca>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
Currently, on HS/EMU devices, MPU power state forced to on during PM
init by the save secure RAM code. Rather than forcing the state of
MPU powerdomain to on, simply read the current value and restore it
after the ROM code has run.
This only affects the !CPUidle case since when CPUidle is enabled, the
MPU power state is dynamically changed by CPUidle. In the !CPUidle
case, MPU power state is initialized once at init and never touched.
Acked-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Always allow backtraces when using oprofile on ARM, even if a PMU
isn't present. Restores functionality originally introduced in commit
1b7b56982f ("oprofile: Always allow
backtraces on ARM") by Richard Purdie.
It is not that obvious, but there is now only one oprofile_arch_init()
function. So the .backtrace callback is available also in timer mode.
Implemented by removing code and using stubs for oprofile_perf_{init,
exit} provided by <linux/oprofile.h>. This allows cleaning of other
architecture specific implementations too.
Cc: stable@kernel.org # 37.x
Signed-off-by: Ari Kauppi <kauppi@papupata.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Robert Richter <robert.richter@amd.com>
This fixes a machine hang after a gpio irq triggered.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: wacom - pass touch resolution to clients through input_absinfo
Input: wacom - add 2 Bamboo Pen and touch models
Input: sysrq - ensure sysrq_enabled and __sysrq_enabled are consistent
Input: sparse-keymap - fix KEY_VSW handling in sparse_keymap_setup
Input: tegra-kbc - add tegra keyboard driver
Input: gpio_keys - switch to using request_any_context_irq
Input: serio - allow registered drivers to get status flag
Input: ct82710c - return proper error code for ct82c710_open
Input: bu21013_ts - added regulator support
Input: bu21013_ts - remove duplicate resolution parameters
Input: tnetv107x-ts - don't treat NULL clk as an error
Input: tnetv107x-keypad - don't treat NULL clk as an error
Fix up trivial conflicts in drivers/input/keyboard/Makefile due to
additions of tc3589x/Tegra drivers
The -rt patches change the console_semaphore to console_mutex. As a
result, a quite large chunk of the patches changes all
acquire/release_console_sem() to acquire/release_console_mutex()
This commit makes things use more neutral function names which dont make
implications about the underlying lock.
The only real change is the return value of console_trylock which is
inverted from try_acquire_console_sem()
This patch also paves the way to switching console_sem from a semaphore to
a mutex.
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: make console_trylock return 1 on success, per Geert]
Signed-off-by: Torben Hohn <torbenh@gmx.de>
Cc: Thomas Gleixner <tglx@tglx.de>
Cc: Greg KH <gregkh@suse.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm:
ALSA: AACI: fix timeout duration
ALSA: AACI: fix timeout condition checking
ARM: 6636/1: ep93xx: default multiplexed gpio ports to gpio mode
ARM: 6637/1: Make the argument to virt_to_phys() "const volatile"
ARM: twd: ensure timer reload is reprogrammed on entry to periodic mode
ARM: 6635/2: Configure reference clock for Versatile Express timers
ARM: versatile: name configuration options after actual board names
ARM: realview: name configuration options after actual board names
ARM: realview,vexpress: fix section mismatch warning for pen_release
ARM: 6632/3: mmci: stop using the blockend interrupts
The EP93xx C and D GPIO ports are multiplexed with the Keypad Interface
peripheral. At power-up they default into non-GPIO mode with the Key
Matrix controller enabled so these ports are unusable for GPIO. Note
that the Keypad Interface peripheral is only available in the EP9307,
EP9312, and EP9315 processor variants.
The keypad support will clear the DeviceConfig bits appropriately to
enable the Keypad Interface when the driver is loaded. And, when the
driver is unloaded it will set the bits to return the ports to GPIO mode.
To make these ports available for GPIO after power-up on all EP93xx
processor variants, set the KEYS and GONK bits in the DeviceConfig
register.
Similarly, the E, G, and H ports are multiplexed with the IDE Interface
peripheral. At power-up these also default into non-GPIO mode. Note
that the IDE peripheral is only available in the EP9312 and EP9315
processor variants.
Since an IDE driver is not even available in mainline, set the EONIDE,
GONIDE, and HONIDE bits in the DeviceConfig register so that these
ports will be available for GPIO use after power-up.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Changing the virt_to_phys() argument to "const volatile void *" avoids
compiler warnings in some situations where this function is used.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ensure that the twd timer reload value is reprogrammed each time we
enter periodic mode. This ensures that the reload value is always
reset correctly.
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Timers on Versatile Express mainboard are used as system clock/event
sources. Driver assumes that they are clocked with 1MHz signal.
Old V2M firmware apparently configured it by default, but on newer
boards one can observe that "sleep 1" command takes over 30 seconds
to finish, as the timers are fed with 32kHz instead...
This patch performs required magic and also removes code clearing
timer's control registers, as exactly the same operations are
performed by the timer driver few jiffies later.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Update the option text to those which appear on the front of the
appropriate board user guides. This gives consistent board naming, and
makes it obvious which option is for which platform.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As no one seems to really know which configuration options tie up with
which boards, I thought I'd do some investigation and try to work it
out. After discussion with some folk in linaro, I think I have this
nailed.
The names are updated to use the name on the front of the appropriate
board user guide for the various baseboards, which I've taken to be
the official name for each board.
I haven't significantly updated the descriptions for the tiles as that
is even less clear - as far as I can see on ARMs website, there is no
Cortex-A9 tile for Realview EB - only ARM11MPCore, ARM1156T2F-S,
ARM1176TZF-S and Cortex-R4F. So exactly what this 'Multicore Cortex-A9
Tile' is...
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix two section mismatch warnings in the platform SMP bringup code for
Realview and Versatile Express:
WARNING: arch/arm/mach-realview/built-in.o(.text+0x8ac): Section mismatch in reference from the function write_pen_release() to the variable .cpuinit.data:pen_release
The function write_pen_release() references
the variable __cpuinitdata pen_release.
This is often because write_pen_release lacks a __cpuinitdata
annotation or the annotation of pen_release is wrong.
WARNING: arch/arm/mach-vexpress/built-in.o(.text+0x7b4): Section mismatch in reference from the function write_pen_release() to the variable .cpuinit.data:pen_release
The function write_pen_release() references
the variable __cpuinitdata pen_release.
This is often because write_pen_release lacks a __cpuinitdata
annotation or the annotation of pen_release is wrong.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Function _sr_lookup, defined in the same file, returns ERR_PTR not NULL in
an error case.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier f;
@@
f(...) { ... return ERR_PTR(...); }
@@
identifier r.f, fld;
expression x;
statement S1,S2;
@@
x = f(...)
... when != IS_ERR(x)
(
if (IS_ERR(x) ||...) S1 else S2
|
*x->fld
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Kevin Hilman <khilman@ti.com>
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
omap: DMA: clear interrupt status correctly
OMAP3: Devkit8000: Fix tps65930 pullup/pulldown configuration
arm: omap3: cm-t3517: minor comment fix
arm: omap3: cm-t3517: rtc fix
omap1: Fix sched_clock implementation when both MPU timer and 32K timer are used
omap1: Fix booting for 15xx and 730 with omap1_defconfig
omap1: Fix sched_clock for the MPU timer
OMAP: PRCM: remove duplicated headers
OMAP4: clockdomain: bypass unimplemented wake-up dependency functions on OMAP4
OMAP: counter_32k: init clocksource as part of machine timer init
_CLK_SET_RATE does not only handle the cpu clock but also other
clocks, so do not hardcode the HW_CLKCTRL_CPU register.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
reg | (1 << clk->enable_shift) always evaluates to true. Switch it
to & which makes much more sense
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
This patch adds support for the internal matrix keyboard controller for
Nvidia Tegra platforms.
Signed-off-by: Rakesh Iyer <riyer@nvidia.com>
Reviewed-by: Trilok Soni <tsoni@codeaurora.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* akpm:
kernel/smp.c: consolidate writes in smp_call_function_interrupt()
kernel/smp.c: fix smp_call_function_many() SMP race
memcg: correctly order reading PCG_USED and pc->mem_cgroup
backlight: fix 88pm860x_bl macro collision
drivers/leds/ledtrig-gpio.c: make output match input, tighten input checking
MAINTAINERS: update Atmel AT91 entry
mm: fix truncate_setsize() comment
memcg: fix rmdir, force_empty with THP
memcg: fix LRU accounting with THP
memcg: fix USED bit handling at uncharge in THP
memcg: modify accounting function for supporting THP better
fs/direct-io.c: don't try to allocate more than BIO_MAX_PAGES in a bio
mm: compaction: prevent division-by-zero during user-requested compaction
mm/vmscan.c: remove duplicate include of compaction.h
memblock: fix memblock_is_region_memory()
thp: keep highpte mapped until it is no longer needed
kconfig: rename CONFIG_EMBEDDED to CONFIG_EXPERT
The meaning of CONFIG_EMBEDDED has long since been obsoleted; the option
is used to configure any non-standard kernel with a much larger scope than
only small devices.
This patch renames the option to CONFIG_EXPERT in init/Kconfig and fixes
references to the option throughout the kernel. A new CONFIG_EMBEDDED
option is added that automatically selects CONFIG_EXPERT when enabled and
can be used in the future to isolate options that should only be
considered for embedded systems (RISC architectures, SLOB, etc).
Calling the option "EXPERT" more accurately represents its intention: only
expert users who understand the impact of the configuration changes they
are making should enable it.
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Acked-by: David Woodhouse <david.woodhouse@intel.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Greg KH <gregkh@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Robin Holt <holt@sgi.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add platform data for MIPI-DSI and LCDC on the AG5EVM
board. The sh73a0 clkdev bindings are also updated.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
PLL1 and PLL2 in the sh73a0 CPGA has a CFG bit that
must be taken into account to correctly calculate the
frequency.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
When clearing the DMA channel, clear all status bits.
When handling a DMA interrupt, clear only the interrupt
status bits that have been read and are passed to the
channel's interrupt handler, not every status bit.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: G, Manjunath Kondaiah <manjugk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
gpio7 on the tps65930 is used as an output on the devkit8000 and
gpio1 is not connected. Remove gpio7 and change gpio1 to pulldown
Signed-off-by: Daniel Morsing <daniel.morsing@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Earlier patches select HAVE_SCHED_CLOCK for omaps. To have working sched_clock
also for MPU timer, we need to implement it in a way where the right one gets
selected during the runtime.
Signed-off-by: Tony Lindgren <tony@atomide.com>
For omap15xx and 730 we need to use the MPU timer
as the 32K timer is not available. For omap16xx
we want to use the 32K timer because of PM. Fix this
by allowing to build in both timers.
Signed-off-by: Tony Lindgren <tony@atomide.com>
* Pins 2 and 4 of switch 33 are documented as don't care on the PCB,
my testing seems to confirm this.
* I have been unable to do anything sensible with S1 set to on.
Am I missing something with regards to MMC1?
* Clarify which driver is needed for each switch setting.
* Should the AP4 board code be updated to allow the
SHDI driver to access SHDI1 as the mackerel code does?
Signed-off-by: Simon Horman <horms@verge.net.au>
Acked-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
A few headers are included twice, remove them.
Found the following errors using make includecheck:
arch/arm/mach-omap2/clock44xx_data.c: prm44xx.h is
included more than once.
arch/arm/mach-omap2/clockdomains44xx_data.c: cm1_44xx.h
is included more than once.
arch/arm/mach-omap2/clockdomains44xx_data.c: cm2_44xx.h
is included more than once.
arch/arm/mach-omap2/powerdomain2xxx_3xxx.c: prm-regbits-34xx.h
is included more than once.
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Felipe Balbi <balbi@ti.com>
[paul@pwsan.com: dropped lists from patch cc:s; tweaked subject line]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit 56a6a19dff ("omap2plus: prm:
Trvial build break fix for undefined reference to
'omap2_prm_read_mod_reg'") generates a lot of warnings on boot since
clockdomain functions that manipulate wake-up dependencies are not
implemented yet on OMAP4 for 2.6.38. This patch bypasses the OMAP2/3
functions on OMAP4, which in turn avoids the warnings when the
functions would attempt to call the underlying OMAP2/3 PRCM functions.
A one-line warning is still logged from the clockdomain code that the
OMAP4 wake-up dependency code is not yet implemented.
A clockdomain wake-up and sleep dependency implementation for OMAP4
from Rajendra should be possible to merge during the 2.6.39 merge
window:
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg41748.htmlhttp://www.mail-archive.com/linux-omap@vger.kernel.org/msg42222.html
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
After commit dc548fbbd2 ("ARM: omap: convert
sched_clock() to use new infrastructure"), OMAPs that use the 32KiHz
"synchronization timer" as their clocksource crash during boot:
[ 0.000000] OMAP clockevent source: GPTIMER1 at 32768 Hz
[ 0.000000] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[ 0.000000] pgd = c0004000
[ 0.000000] [00000000] *pgd=00000000
[ 0.000000] Internal error: Oops: 80000005 [#1] SMP
[ 0.000000] last sysfs file:
[ 0.000000] Modules linked in:
[ 0.000000] CPU: 0 Tainted: G W (2.6.37-07734-g2467802 #7)
[ 0.000000] PC is at 0x0
[ 0.000000] LR is at sched_clock_poll+0x2c/0x3c
[ 0.000000] pc : [<00000000>] lr : [<c0060b74>] psr: 600001d3
[ 0.000000] sp : c058bfd0 ip : c058a000 fp : 00000000
[ 0.000000] r10: 00000000 r9 : 411fc092 r8 : 800330c8
[ 0.000000] r7 : c05a08e0 r6 : c0034c48 r5 : c05ffc40 r4 : c0034c4c
[ 0.000000] r3 : c05ffe6c r2 : c05a0bc0 r1 : c059f098 r0 : 00000000
[ 0.000000] Flags: nZCv IRQs off FIQs off Mode SVC_32 ISA ARM Segment kernel
[ 0.000000] Control: 10c53c7f Table: 8000404a DAC: 00000017
This is due to the recent ARM init_sched_clock() changes and the late
initialization of the counter_32k clock source. More information here:
http://marc.info/?l=linux-omap&m=129513468605208&w=2
Fix by initializing the counter_32k clocksource during the machine timer
initialization.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Fix a typo for the sh73a0 CPGA code dealing with the IrDA
hardware block on the AG5EVM board.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix the M3 field offset for the FRQCRA register
in the sh73a0 CPGA. It should be 12, not 8.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
set_irq_type() should only be used for external IRQ pins,
so update the G3EVM board code to remove low level request.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Enable the MFIS2 interrupt source in the INTCS interrupt
controller included in the sh7372 processor. The priority
field is constantly enabled to let the interrupt through to
both the ARM side and the SH side.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* git://git.infradead.org/mtd-2.6: (59 commits)
mtd: mtdpart: disallow reading OOB past the end of the partition
mtd: pxa3xx_nand: NULL dereference in pxa3xx_nand_probe
UBI: use mtd->writebufsize to set minimal I/O unit size
mtd: initialize writebufsize in the MTD object of a partition
mtd: onenand: add mtd->writebufsize initialization
mtd: nand: add mtd->writebufsize initialization
mtd: cfi: add writebufsize initialization
mtd: add writebufsize field to mtd_info struct
mtd: OneNAND: OMAP2/3: prevent regulator sleeping while OneNAND is in use
mtd: OneNAND: add enable / disable methods to onenand_chip
mtd: m25p80: Fix JEDEC ID for AT26DF321
mtd: txx9ndfmc: limit transfer bytes to 512 (ECC provides 6 bytes max)
mtd: cfi_cmdset_0002: add support for Samsung K8D3x16UxC NOR chips
mtd: cfi_cmdset_0002: add support for Samsung K8D6x16UxM NOR chips
mtd: nand: ams-delta: drop omap_read/write, use ioremap
mtd: m25p80: add debugging trace in sst_write
mtd: nand: ams-delta: select for built-in by default
mtd: OneNAND: lighten scary initial bad block messages
mtd: OneNAND: OMAP2/3: add support for command line partitioning
mtd: nand: rearrange ONFI revision checking, add ONFI 2.3
...
Fix up trivial conflict in drivers/mtd/Kconfig as per DavidW.
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx: (63 commits)
ARM: PL08x: cleanup comments
Update CONFIG_MD_RAID6_PQ to CONFIG_RAID6_PQ in drivers/dma/iop-adma.c
ARM: PL08x: fix a warning
Fix dmaengine_submit() return type
dmaengine: at_hdmac: fix race while monitoring channel status
dmaengine: at_hdmac: flags located in first descriptor
dmaengine: at_hdmac: use subsys_initcall instead of module_init
dmaengine: at_hdmac: no need set ACK in new descriptor
dmaengine: at_hdmac: trivial add precision to unmapping comment
dmaengine: at_hdmac: use dma_address to program DMA hardware
pch_dma: support new device ML7213 IOH
ARM: PL08x: prevent dma_set_runtime_config() reconfiguring memcpy channels
ARM: PL08x: allow dma_set_runtime_config() to return errors
ARM: PL08x: fix locking between prepare function and submit function
ARM: PL08x: introduce 'phychan_hold' to hold on to physical channels
ARM: PL08x: put txd's on the pending list in pl08x_tx_submit()
ARM: PL08x: rename 'desc_list' as 'pend_list'
ARM: PL08x: implement unmapping of memcpy buffers
ARM: PL08x: store prep_* flags in async_tx structure
ARM: PL08x: shrink srcbus/dstbus in txd structure
...
* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: fix missing branch in __error_a
ARM: fix /proc/$PID/stack on SMP
ARM: Fix build regression on SA11x0, PXA, and H720x targets
ARM: 6625/1: use memblock memory regions for "System RAM" I/O resources
ARM: fix wrongly patched constants
ARM: 6624/1: fix dependency for CONFIG_SMP_ON_UP
ARM: 6623/1: Thumb-2: Fix out-of-range offset for Thumb-2 in proc-v7.S
ARM: 6622/1: fix dma_unmap_sg() documentation
ARM: 6621/1: bitops: remove condition code clobber for CLZ
ARM: 6620/1: Change misleading warning when CONFIG_CMDLINE_FORCE is used
ARM: 6619/1: nommu: avoid mapping vectors page when !CONFIG_MMU
ARM: sched_clock: make minsec argument to clocks_calc_mult_shift() zero
ARM: sched_clock: allow init_sched_clock() to be called early
ARM: integrator: fix compile warning in cpu.c
ARM: 6616/1: Fix ep93xx-fb init/exit annotations
ARM: twd: fix display of twd frequency
ARM: udelay: prevent math rounding resulting in short udelays
When DEBUG_LL is not set, we don't want __error_a re-entering
__lookup_machine_type - we want it to go to the error function. This
used to be the case before we reorganized the layout for hotplug cpu,
as we used to fall through to __error. With the changed layout, we
need an explicit branch here instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Drive strength for PXA910 is a 2 bit value but because of the mapping in
plat-pxa/mfp.h needs to be shifted up one bit to handle real
location in mfp registers. (MMP2 and PXA910 drive strength start
at bit 11 while PXA168 starts at bit 10).
Values 0, 1, 2, and 3 effectively need to be
0, 2, 4, and 6 to fit into register. 8 does not work.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Drive strength for MMP2 is a 2 bit value but because of the mapping in
plat-pxa/mfp.h needs to be shifted up one bit to handle real
location in mfp registers. (MMP2 and PXA910 drive strength start
at bit 11 while PXA168 starts at bit 10).
Values 0, 1, 2, and 3 effectively need to be
0, 2, 4, and 6 to fit into register. 8 does not work.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Tested-by: John Watlington <wad@laptop.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Rabin Vincent reports:
| On SMP, this BUG() in save_stack_trace_tsk() can be easily triggered
| from user space by reading /proc/$PID/stack, where $PID is any pid but
| the current process:
|
| if (tsk != current) {
| #ifdef CONFIG_SMP
| /*
| * What guarantees do we have here that 'tsk'
| * is not running on another CPU?
| */
| BUG();
| #else
Fix this by replacing the BUG() with an entry to terminate the stack
trace, returning an empty trace - I'd rather not expose the dwarf
unwinder to a volatile stack of a running thread.
Reported-by: Rabin Vincent <rabin@rab.in>
Tested-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Build errors similar this appeared in todays kautobuild for the above
targets:
In file included from arch/arm/include/asm/pgtable.h:461,
from arch/arm/mach-pxa/generic.c:26:
include/asm-generic/pgtable.h: In function 'ptep_test_and_clear_young':
include/asm-generic/pgtable.h:29: error: dereferencing pointer to incomplete type
None of the .c files including asm/pgtable.h with this error is using
this header, so simply remove the include.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Do not use memory bank info to request the "system ram" resources as
they do not track holes created by memblock_remove inside
machine's reserve callback. If the removed memory is passed as
platform_device's ioresource, then drivers that call
request_mem_region would fail due to a conflict with the incorrectly
configured system ram resource.
Instead, iterate through the regions of memblock.memory and add
those as "System RAM" resources.
Signed-off-by: Dima Zavin <dima@android.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (27 commits)
omap4: Fix ULPI PHY init for ES1.0 SDP
omap3: beaglexm: fix power on of DVI
omap3: igep3: Add omap_reserve functionality
omap3: beaglexm: fix DVI reset GPIO
omap3: beaglexm: fix EHCI power up GPIO dir
omap3: igep2: Add keypad support
omap3: igep3: Fix IGEP module second MMC channel power supply
omap3: igep3: Add USB EHCI support for IGEP module
omap3: clocks: Fix build error 'CK_3430ES2' undeclared here
arm: omap4: pandaboard: turn on PHY reference clock at init
omap2plus: prm: Trvial build break fix for undefined reference to 'omap2_prm_read_mod_reg'
omap2plus: voltage: Trivial linking fix for 'EINVAL' undeclared
omap2plus: voltage: Trivial linking fix 'undefined reference'
omap2plus: voltage: Trivial warning fix 'no return statement'
omap2plus: clockdomain: Trivial fix for build break because of clktrctrl_mask
arm: omap: gpio: don't access irq_desc array directly
omap2+: pm_bus: make functions used as pointers as static
OMAP: GPIO: fix _set_gpio_triggering() for OMAP2+
OMAP2+: TWL: include pm header for init protos
OMAP2+: TWL: make conversion routines static
...
Fix up conflicts in arch/arm/mach-omap2/board-omap3beagle.c ("DVI reset
GPIO" vs "use generic DPI panel driver")
The GS_IA18_S (GMS) is a carrier board from GeoSIG Ltd used with the
Stamp9G20 SoM from Taskit company.
It operate as an internet accelerometer.
Signed-off-by: Igor Plyatov <plyatov@gmail.com>
[nicolas.ferre@atmel.com: rm Kconfig, whitespace fixes, change machine name]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
e3d9c625 (ARM: CPU hotplug: fix hard-coded control register constants)
changed the wrong constants in the hotplug assembly code. Fix this.
Reported-by: viresh kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since commit
6d803ba (ARM: 6483/1: arm & sh: factorised duplicated clkdev.c)
platforms need to select CLKDEV_LOOKUP instead of COMMON_CLKDEV and need
to include <linux/clkdev.h>.
Cc: Shawn Guo <shawn.guo@freescale.com>
Cc: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This depends on !XIP_KERNEL and not !XIP.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit d30e45e (ARM: pgtable: switch order of Linux vs hardware page tables)
introduced a pre-increment addressing offset which is out of range for
Thumb-2. Thumb-2 only permits offsets <256. So split the intruction in
two for Thumb-2.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'idle-release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-idle-2.6:
cpuidle/x86/perf: fix power:cpu_idle double end events and throw cpu_idle events from the cpuidle layer
intel_idle: open broadcast clock event
cpuidle: CPUIDLE_FLAG_CHECK_BM is omap3_idle specific
cpuidle: CPUIDLE_FLAG_TLB_FLUSHED is specific to intel_idle
cpuidle: delete unused CPUIDLE_FLAG_SHALLOW, BALANCED, DEEP definitions
SH, cpuidle: delete use of NOP CPUIDLE_FLAGS_SHALLOW
cpuidle: delete NOP CPUIDLE_FLAG_POLL
ACPI: processor_idle: delete use of NOP CPUIDLE_FLAGs
cpuidle: Rename X86 specific idle poll state[0] from C0 to POLL
ACPI, intel_idle: Cleanup idle= internal variables
cpuidle: Make cpuidle_enable_device() call poll_idle_init()
intel_idle: update Sandy Bridge core C-state residency targets
pte alloc routines must wait for split_huge_page if the pmd is not present
and not null (i.e. pmd_trans_splitting). The additional branches are
optimized away at compile time by pmd_trans_splitting if the config option
is off. However we must pass the vma down in order to know the anon_vma
lock to wait for.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Four architectures (arm, mips, sparc, x86) use __vmalloc_area() for
module_init(). Much of the code is duplicated and can be generalized in a
globally accessible function, __vmalloc_node_range().
__vmalloc_node() now calls into __vmalloc_node_range() with a range of
[VMALLOC_START, VMALLOC_END) for functionally equivalent behavior.
Each architecture may then use __vmalloc_node_range() directly to remove
the duplication of code.
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Because ag5evm board setup code uses gpio functions,
ARCH_REQUIRE_GPIOLIB should be set in Kconfig.
Otherwise, the first build with defconfig fails.
Signed-off-by: Takashi YOSHII <takashi.yoshii.zj@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The latest rmobile-latest doesn't run on ag5evm because of a
small mistake on initialization.
Though, I don't have any idea to write them smart.
anyway,
On sh73a0, GIC cpu_base is 0xf0000100 but 0xf0001000.
Signed-off-by: Takashi YOSHII <takashi.yoshii.zj@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'rmobile-latest' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
ARM: mach-shmobile: Kill off unused !gpio_is_valid() case
ARM: mach-shmobile: sh7372 Enable SDIO IRQs for Mackerel
ARM: mach-shmobile: sh7377 Enable SDIO IRQs
ARM: mach-shmobile: sh7367 Enable SDIO IRQs
ARM: mach-shmobile: sh7372 Enable SDIO IRQs
ARM: mach-shmobile: mackerel: Add touchscreen ST1232 support
ARM: mach-shmobile: ap4eb: SCIF port for earlyprintk when using zboot
ARM: mach-shmobile: mackerel: SCIF port for earlyprintk when using zboot
ARM: mach-shmobile: mackerel: Add support get_cd in CN23
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/fbdev-2.6: (29 commits)
video: move SH_MIPI_DSI/SH_LCD_MIPI_DSI to the top of menu
fbdev: Implement simple blanking in pseudocolor modes for vt8500lcdfb
video: imx: Update the manufacturer's name
nuc900fb: don't treat NULL clk as an error
s3c2410fb: don't treat NULL clk as an error
video: tidy up modedb formatting.
video: matroxfb: Correct video option in comments and kernel config help.
fbdev: sh_mobile_hdmi: simplify pointer handling
fbdev: sh_mobile_hdmi: framebuffer notifiers have to be registered
fbdev: sh_mobile_hdmi: add command line option to use the preferred EDID mode
OMAP: DSS2: Introduce omap_channel as an omap_dss_device parameter, add new overlay manager.
OMAP: DSS2: Use dss_features to handle DISPC bits removed on OMAP4
OMAP: DSS2: LCD2 Channel Changes for DISPC
OMAP: DSS2: Change remaining DISPC functions for new omap_channel argument
OMAP: DSS2: Introduce omap_channel argument to DISPC functions used by interface drivers
OMAP: DSS2: Represent DISPC register defines with channel as parameter
OMAP: DSS2: Add dss_features for omap4 and overlay manager related features
OMAP: DSS2: Clean up DISPC color mode validation checks
OMAP: DSS2: Add back authors of panel-generic.c based drivers
OMAP: DSS2: remove generic DPI panel driver duplicated panel drivers
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6: (45 commits)
regulator: missing index in PTR_ERR() in isl6271a_probe()
regulator: Assign return value of mc13xxx_reg_rmw to ret
regulator: Add initial per-regulator debugfs support
regulator: Make regulator_has_full_constraints a bool
regulator: Clean up logging a bit
regulator: Optimise out noop voltage changes
regulator: Add API to re-apply voltage to hardware
regulator: Staticise non-exported functions in mc13892
regulator: Only notify voltage changes when they succeed
regulator: Provide a selector based set_voltage_sel() operation
regulator: Factor out voltage set operation into a separate function
regulator: Convert WM8994 to use get_voltage_sel()
regulator: Convert WM835x to use get_voltage_sel()
regulator: Allow modular build of mc13xxx-core
regulator: support PMIC mc13892
make mc13783 regulator code generic
Change the register name definitions for mc13783
mach-ux500: Updated and connected ab8500 regulator board configuration
regulators: Removed macros for initialization of ab8500 regulators
regulators: Added verbose debug messages to ab8500 regulators
...
Kukjin Kim