Extend the Intel and AMD event definitions with generic front-end and
back-end stall events.
( These are only approximations - suggestions are welcome for better events. )
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Link: http://lkml.kernel.org/n/tip-7y40wib8n001io7hjpn1dsrm@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add two generic hardware events: front-end and back-end stalled cycles.
These events measure conditions when the CPU is executing code but its
capabilities are not fully utilized. Understanding such situations and
analyzing them is an important sub-task of code optimization workflows.
Both events limit performance: most front end stalls tend to be caused
by branch misprediction or instruction fetch cachemisses, backend
stalls can be caused by various resource shortages or inefficient
instruction scheduling.
Front-end stalls are the more important ones: code cannot run fast
if the instruction stream is not being kept up.
An over-utilized back-end can cause front-end stalls and thus
has to be kept an eye on as well.
The exact composition is very program logic and instruction mix
dependent.
We use the terms 'stall', 'front-end' and 'back-end' loosely and
try to use the best available events from specific CPUs that
approximate these concepts.
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Link: http://lkml.kernel.org/n/tip-7y40wib8n000io7hjpn1dsrm@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
While tracking down the reason for an ioremap() failure I was
distracted by the WARN_ONCE() in __ioremap_caller().
Performing a WARN_ONCE() sanity check before the mapping
is successful seems pointless if the caller sends bad values.
A case in point is when the BIOS provides erroneous screen_info
values causing vesafb_probe() to request an outrageuous size.
The WARN_ONCE is then wasted on bogosity. Move the warning to a
point where the mapping has been successfully allocated.
Addresses:
http://bugs.launchpad.net/bugs/772042
Reviewed-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Link: http://lkml.kernel.org/r/4DB99D2E.9080106@canonical.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Normally sys_rt_sigreturn() restores the old current->blocked which was
changed by handle_signal(), and unblocking is always fine.
But the debugger or application itself can change frame->uc_sigmask and
thus we need set_current_blocked()->retarget_shared_pending().
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: Matt Fleming <matt.fleming@linux.intel.com>
Acked-by: Tejun Heo <tj@kernel.org>
This is ugly, but if sigprocmask() needs retarget_shared_pending() then
handle signal should follow this logic. In theory it is newer correct to
add the new signals to current->blocked, the signal handler can sleep/etc
so we should notify other threads in case we block the pending signal and
nobody else has TIF_SIGPENDING.
Of course, this change doesn't make signals faster :/
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: Matt Fleming <matt.fleming@linux.intel.com>
Acked-by: Tejun Heo <tj@kernel.org>
The USB and SATA ioapic interrrupt pins are configured as edge type,
but need to be level type interrupts to work correctly.
[ tglx: Split out from the combo patch ]
Cc: Torben Hohn <torbenh@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: http://lkml.kernel.org/r/%3C20110427143052.GA15211%40linutronix.de%3E
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We use io_apic_setup_irq_pin() in order to configure pin's interrupt
number polarity and type. This is done on every irq_create_of_mapping()
which happens for instance during pci enable calls. Level typed
interrupts are masked by default, edge are unmasked.
On the first ->xlate() call the level interrupt is configured and
masked. The driver calls request_irq() and the line is unmasked. Lets
assume the interrupt line is shared with another device and we call
pci_enable_device() for this device. The ->xlate() configures the pin
again and it is masked. request_irq() does not unmask the line because
it _is_ already unmasked according to its internal state. So the
interrupt will never be unmasked again.
This patch is based on an earlier work by Torben Hohn and solves the
problem by configuring the pin only once. Since all devices must agree
on the same type and polarity there is no point in configuring the pin
more than once.
[ tglx: Split out the ce4100 part into a separate patch ]
Cc: Torben Hohn <torbenh@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: http://lkml.kernel.org/r/%3C20110427143052.GA15211%40linutronix.de%3E
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Use the UOPS_EXECUTED.*,c=1,i=1 event on Intel CPUs - it is a rather
good indicator of CPU execution stalls, more sensitive and more inclusive
than the 0xa2 resource stalls event (which does not count nearly as many
stall types).
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Link: http://lkml.kernel.org/n/tip-7y40wib8n1eqio7hjpn2dsrm@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
It was noticed that P4 machines were generating double NMIs for
each perf event. These extra NMIs lead to 'Dazed and confused'
messages on the screen.
I tracked this down to a P4 quirk that said the overflow bit had
to be cleared before re-enabling the apic LVT mask. My first
attempt was to move the un-masking inside the perf nmi handler
from before the chipset NMI handler to after.
This broke Nehalem boxes that seem to like the unmasking before
the counters themselves are re-enabled.
In order to keep this change simple for 2.6.39, I decided to
just simply move the apic LVT un-masking to the beginning of all
the chipset NMI handlers, with the exception of Pentium4's to
fix the double NMI issue.
Later on we can move the un-masking to later in the handlers to
save a number of 'extra' NMIs on those particular chipsets.
I tested this change on a P4 machine, an AMD machine, a Nehalem
box, and a core2quad box. 'perf top' worked correctly along
with various other small 'perf record' runs. Anything high
stress breaks all the machines but that is a different problem.
Thanks to various people for testing different versions of this
patch.
Reported-and-tested-by: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Don Zickus <dzickus@redhat.com>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Link: http://lkml.kernel.org/r/1303900353-10242-1-git-send-email-dzickus@redhat.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
CC: Cyrill Gorcunov <gorcunov@gmail.com>
Conflicts:
include/linux/perf_event.h
Merge reason: pick up the latest jump-label enhancements, they are cooked ready.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The new PERF_COUNT_HW_STALLED_CYCLES event tries to approximate
cycles the CPU does nothing useful, because it is stalled on a
cache-miss or some other condition.
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Link: http://lkml.kernel.org/n/tip-fue11vymwqsoo5to72jxxjyl@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
On Nehalem CPUs the retired branch-misses event can be completely bogus,
when there are no branch-misses occuring. When there are a lot of branch
misses then the count is pretty accurate. Still, this leaves us with an
event that over-counts a lot.
Detect this erratum and work it around by using BR_MISP_EXEC.ANY events.
These will also count speculated branches but still it's a lot more
precise in practice than the architectural event.
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Link: http://lkml.kernel.org/n/tip-yyfg0bxo9jsqxd6a0ovfny27@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Currently the x86 backend incorrectly assumes that any BRANCH_INSN
with sample_period==1 is a BTS request. This is not true when we do
frequency driven profiling such as 'perf record -e branches'.
Solves this error:
$ perf record -e branches ./array
Error: sys_perf_event_open() syscall returned with 95 (Operation not supported).
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Reported-by: Ingo Molnar <mingo@elte.hu>
Cc: "Metzger, Markus T" <markus.t.metzger@intel.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Link: http://lkml.kernel.org/n/tip-rd2y4ct71hjawzz6fpvsy9hg@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When we use BIOS function e801 to probe memory, we should use ax/bx
(or cx/dx) as a pair, not mix and match. This was a typo during the
translation from assembly code, and breaks at least one set of
machines in the field (which return cx = dx = 0).
Reported-and-tested-by: Chris Samuel <chris@csamuel.org>
Fix-proposed-by: Thomas Meyer <thomas@m3y3r.de>
Link: http://lkml.kernel.org/r/1303566747.12067.10.camel@localhost.localdomain
While the tracer accesses ptrace breakpoints, the child task may
concurrently exit due to a SIGKILL and thus release its breakpoints
at the same time. We can then dereference some freed pointers.
To fix this, hold a reference on the child breakpoints before
manipulating them.
Reported-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Prasad <prasad@linux.vnet.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: v2.6.33.. <stable@kernel.org>
Link: http://lkml.kernel.org/r/1302284067-7860-3-git-send-email-fweisbec@gmail.com
Recently, we had a build failure on !CONFIG_PARAVIRT due to a
callback ->wbinvd() clashing with a macro wbinvd().
While we worked around the issue, avoid it in the future by
changing the macro (and a few surrounding ones) to an inline
function.
Signed-off-by: Avi Kivity <avi@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Link: http://lkml.kernel.org/r/1303632711-21662-1-git-send-email-avi@redhat.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
It's not enough to simply disable event on overflow the
cpuc->active_mask should be cleared as well otherwise counter
may stall in "active" even in real being already disabled (which
potentially may lead to the situation that user may not use this
counter further).
Don pointed out that:
" I also noticed this patch fixed some unknown NMIs
on a P4 when I stressed the box".
Tested-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Acked-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Don Zickus <dzickus@redhat.com>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Link: http://lkml.kernel.org/r/1303398203-2918-3-git-send-email-dzickus@redhat.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Andi Kleen pointed out that the Intel offcore support patches were merged
without user-space tool support to the functionality:
|
| The offcore_msr perf kernel code was merged into 2.6.39-rc*, but the
| user space bits were not. This made it impossible to set the extra mask
| and actually do the OFFCORE profiling
|
Andi submitted a preliminary patch for user-space support, as an
extension to perf's raw event syntax:
|
| Some raw events -- like the Intel OFFCORE events -- support additional
| parameters. These can be appended after a ':'.
|
| For example on a multi socket Intel Nehalem:
|
| perf stat -e r1b7:20ff -a sleep 1
|
| Profile the OFFCORE_RESPONSE.ANY_REQUEST with event mask REMOTE_DRAM_0
| that measures any access to DRAM on another socket.
|
But this kind of usability is absolutely unacceptable - users should not
be expected to type in magic, CPU and model specific incantations to get
access to useful hardware functionality.
The proper solution is to expose useful offcore functionality via
generalized events - that way users do not have to care which specific
CPU model they are using, they can use the conceptual event and not some
model specific quirky hexa number.
We already have such generalization in place for CPU cache events,
and it's all very extensible.
"Offcore" events measure general DRAM access patters along various
parameters. They are particularly useful in NUMA systems.
We want to support them via generalized DRAM events: either as the
fourth level of cache (after the last-level cache), or as a separate
generalization category.
That way user-space support would be very obvious, memory access
profiling could be done via self-explanatory commands like:
perf record -e dram ./myapp
perf record -e dram-remote ./myapp
... to measure DRAM accesses or more expensive cross-node NUMA DRAM
accesses.
These generalized events would work on all CPUs and architectures that
have comparable PMU features.
( Note, these are just examples: actual implementation could have more
sophistication and more parameter - as long as they center around
similarly simple usecases. )
Now we do not want to revert *all* of the current offcore bits, as they
are still somewhat useful for generic last-level-cache events, implemented
in this commit:
e994d7d23a0b: perf: Fix LLC-* events on Intel Nehalem/Westmere
But we definitely do not yet want to expose the unstructured raw events
to user-space, until better generalization and usability is implemented
for these hardware event features.
( Note: after generalization has been implemented raw offcore events can be
supported as well: there can always be an odd event that is marginally
useful but not useful enough to generalize. DRAM profiling is definitely
*not* such a category so generalization must be done first. )
Furthermore, PERF_TYPE_RAW access to these registers was not intended
to go upstream without proper support - it was a side-effect of the above
e994d7d23a commit, not mentioned in the changelog.
As v2.6.39 is nearing release we go for the simplest approach: disable
the PERF_TYPE_RAW offcore hack for now, before it escapes into a released
kernel and becomes an ABI.
Once proper structure is implemented for these hardware events and users
are offered usable solutions we can revisit this issue.
Reported-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1302658203-4239-1-git-send-email-andi@firstfloor.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The default notifier doesn't make a lot of sense to call in the
correctable errors case. Drop it and emit the mcelog decoding
hint only in the uncorrectable errors case and when no notifier
is registered. Also, limit issuing the "mcelog --ascii" message
in the rare case when we dump unreported CEs before panicking.
While at it, remove unused old x86_mce_decode_callback from the
header.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Nagananda Chumbalkar <Nagananda.Chumbalkar@hp.com>
Cc: Russ Anderson <rja@sgi.com>
Link: http://lkml.kernel.org/r/20110420102349.GB1361@aftab
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The cpu<->node mappings under CONFIG_DEBUG_PER_CPU_MAPS=y
when NUMA emulation is enabled is currently broken because it does
not iterate through every emulated node and bind cpus that have
affinity to it.
NUMA emulation should bind each cpu to every local node to
accurately represent the true NUMA topology of the underlying
machine.
debug_cpumask_set_cpu() needs to be fixed at the same time so
that the debugging information that it emits shows the new
cpumask of the node being assigned when the cpu is being added
or removed.
It can now take responsibility of setting or clearing the cpu
itself to remove the need for duplicate code.
Also change its last parameter, "enable", to have the correct bool
type since it can only be true or false.
-v2: Fix the return statements, by Kosaki Motohiro
Acked-and-Tested-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Andreas Herrmann <herrmann.der.user@googlemail.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/alpine.DEB.2.00.1104201918470.12634@chino.kir.corp.google.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Andreas Herrmann reported that 7d6b46707f ("x86, NUMA: Fix fakenuma
boot failure") causes certain physical NUMA topologies (for example
AMD Magny-Cours) to move sibling cpus to a single node when in reality
they are in separate domains.
This may result in some nodes being completely void of cpus, which
doesn't accurately represent the correct topology. The system will
boot, but will have suboptimal NUMA performance.
This commit was intended as a fix for NUMA emulation, but should
not cause a regression for real NUMA machines as a side effect.
( There will be a separate fix for the numa-debug code, which
will not affect physical topologies. )
Reported-by: Andreas Herrmann <herrmann.der.user@googlemail.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/alpine.DEB.2.00.1104201918110.12634@chino.kir.corp.google.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'stable/bug-fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen: mask_rw_pte: do not apply the early_ioremap checks on x86_32
xen: do not create the extra e820 region at an addr lower than 4G
If the backends, which use these two functions, are compiled as
a module we need these two functions to be exported.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The two "is_early_ioremap_ptep" checks in mask_rw_pte are only used on
x86_64, in fact early_ioremap is not used at all to setup the initial
pagetable on x86_32.
Moreover on x86_32 the two checks are wrong because the range
pgt_buf_start..pgt_buf_end initially should be mapped RW because
the pages in the range are not pagetable pages yet and haven't been
cleared yet. Afterwards considering the pgt_buf_start..pgt_buf_end is
part of the initial mapping, xen_alloc_pte is capable of turning
the ptes RO when they become pagetable pages.
Fix the issue and improve the readability of the code providing two
different implementation of mask_rw_pte for x86_32 and x86_64.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Do not add the extra e820 region at a physical address lower than 4G
because it breaks e820_end_of_low_ram_pfn().
It is OK for us to move the xen_extra_mem_start up and down because this
is the index of the memory that can be ballooned in/out - it is memory
not available to the kernel during bootup.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Device suspend/resume infrastructure is used not only by the suspend
and hibernate code in kernel/power, but also by APM, Xen and the
kexec jump feature. However, commit 40dc166cb5
(PM / Core: Introduce struct syscore_ops for core subsystems PM)
failed to add syscore_suspend() and syscore_resume() calls to that
code, which generally leads to breakage when the features in question
are used.
To fix this problem, add the missing syscore_suspend() and
syscore_resume() calls to arch/x86/kernel/apm_32.c, kernel/kexec.c
and drivers/xen/manage.c.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, gart: Make sure GART does not map physmem above 1TB
x86, gart: Set DISTLBWALKPRB bit always
x86, gart: Convert spaces to tabs in enable_gart_translation
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf, x86: Fix AMD family 15h FPU event constraints
perf, x86: Fix pre-defined cache-misses event for AMD family 15h cpus
perf evsel: Fix use of inherit
perf hists browser: Fix seg fault when annotate null symbol
Correctable errors are considered something rather normal on
modern hardware these days. Even more importantly, correctable
errors mean exactly that - they've been corrected by the
hardware - and there's no need to taint the kernel since
execution hasn't been compromised so far.
Also, drop tainting in the thermal throttling code for a similar
reason: crossing a thermal threshold does not mean corruption.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Acked-by: Nagananda Chumbalkar <Nagananda.Chumbalkar@hp.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Russ Anderson <rja@sgi.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/1303135222-17118-1-git-send-email-bp@amd64.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
End users worry about the error interrupt printout we generate
currently:
pr_debug("APIC error on CPU%d: %02x(%02x)\n",
smp_processor_id(), v , v1);
... and would like to know the reason why error interrupts are generated.
This patch prints out more detailed debug information.
Another practical problem is that dynamic debug is not initialized yet
when the APIC initializes, so the pr_debug() will not output the error
interrupt debug information on bootup. In this patch, we use
apic_printk(APIC_DEBUG, ...), so the apic=debug boot option will print
verbose error interupts during bootup.
Signed-off-by: Youquan Song <youquan.song@intel.com>
Cc: Joe Perches <joe@perches.com>
Cc: hpa@linux.intel.com
Cc: suresh.b.siddha@intel.com
Cc: yong.y.wang@linux.intel.com
Cc: jbaron@redhat.com
Cc: trenn@suse.de
Cc: kent.liu@intel.com
Cc: chaohong.guo@intel.com
Link: http://lkml.kernel.org/r/1302762968-24380-2-git-send-email-youquan.song@intel.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Using ALTERNATIVE() when checking for X86_FEATURE_PERFCTR_CORE avoids
an extra pointer chase and data cache hit.
Signed-off-by: Robert Richter <robert.richter@amd.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1302913676-14352-4-git-send-email-robert.richter@amd.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Depending on the unit mask settings some FPU events may be scheduled
only on cpu counter #3. This patch fixes this.
Signed-off-by: Robert Richter <robert.richter@amd.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Stephane Eranian <eranian@googlemail.com>
Link: http://lkml.kernel.org/r/1302913676-14352-3-git-send-email-robert.richter@amd.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
With AMD cpu family 15h a unit mask was introduced for the Data Cache
Miss event (0x041/L1-dcache-load-misses). We need to enable bit 0
(first data cache miss or streaming store to a 64 B cache line) of
this mask to proper count data cache misses.
Now we set this bit for all families and models. In case a PMU does
not implement a unit mask for event 0x041 the bit is ignored.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Robert Richter <robert.richter@amd.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1302913676-14352-2-git-send-email-robert.richter@amd.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Due to a decoder implementation quirk, some specific Intel CPUs
actually perform better with the "k8_nops" than with the
SDM-recommended NOPs. For runtime-selected NOPs, if we detect those
specific CPUs then use the k8_nops instead of the ones we would
normally use.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jason Baron <jbaron@redhat.com>
Link: http://lkml.kernel.org/r/1303166160-10315-4-git-send-email-hpa@linux.intel.com
Clean up and unify the NOP selection infrastructure:
- Make the atomic 5-byte NOP a part of the selection system.
- Pick NOPs once during early boot and then be done with it.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jason Baron <jbaron@redhat.com>
Link: http://lkml.kernel.org/r/1303166160-10315-3-git-send-email-hpa@linux.intel.com
This patch changes the allocation of the GART aperture to
enforce only natural alignment instead of aligning it on
512MB. This big alignment was used to force the GART
aperture to be over 512MB. This is enforced by using 512MB
as the lower-bound address in the allocation range.
[ hpa: The actual number 512 MiB needs to be revisited, too. ]
Cc: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Link: http://lkml.kernel.org/r/1303134346-5805-2-git-send-email-joerg.roedel@amd.com
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The GART can only map physical memory below 1TB. Make sure
the gart driver in the kernel does not try to map memory
above 1TB.
Cc: <stable@kernel.org>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Link: http://lkml.kernel.org/r/1303134346-5805-5-git-send-email-joerg.roedel@amd.com
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The DISTLBWALKPRB bit must be set for the GART because the
gatt table is mapped UC. But the current code does not set
the bit at boot when the BIOS setup the aperture correctly.
Fix that by setting this bit when enabling the GART instead
of the other places.
Cc: <stable@kernel.org>
Cc: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Link: http://lkml.kernel.org/r/1303134346-5805-4-git-send-email-joerg.roedel@amd.com
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
We only supported the M2P (and P2M) override only for the
GNTMAP_contains_pte type mappings. Meaning that we grants
operations would "contain the machine address of the PTE to update"
If the flag is unset, then the grant operation is
"contains a host virtual address". The latter case means that
the Hypervisor takes care of updating our page table
(specifically the PTE entry) with the guest's MFN. As such we should
not try to do anything with the PTE. Previous to this patch
we would try to clear the PTE which resulted in Xen hypervisor
being upset with us:
(XEN) mm.c:1066:d0 Attempt to implicitly unmap a granted PTE c0100000ccc59067
(XEN) domain_crash called from mm.c:1067
(XEN) Domain 0 (vcpu#0) crashed on cpu#3:
(XEN) ----[ Xen-4.0-110228 x86_64 debug=y Not tainted ]----
and crashing us.
This patch allows us to inhibit the PTE clearing in the PV guest
if the GNTMAP_contains_pte is not set.
On the m2p_remove_override path we provide the same parameter.
Sadly in the grant-table driver we do not have a mechanism to
tell m2p_remove_override whether to clear the PTE or not. Since
the grant-table driver is used by user-space, we can safely assume
that it operates only on PTE's. Hence the implementation for
it to work on !GNTMAP_contains_pte returns -EOPNOTSUPP. In the future
we can implement the support for this. It will require some extra
accounting structure to keep track of the page[i], and the flag.
[v1: Added documentation details, made it return -EOPNOTSUPP instead
of trying to do a half-way implementation]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
futex: Set FLAGS_HAS_TIMEOUT during futex_wait restart setup
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf_event: Fix cgrp event scheduling bug in perf_enable_on_exec()
perf: Fix a build error with some GCC versions
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: Fix erroneous all_pinned logic
sched: Fix sched-domain avg_load calculation
* 'timer-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
RTC: rtc-mrst: follow on to the change of rtc_device_register()
RTC: add missing "return 0" in new alarm func for rtc-bfin.c
RTC: Fix s3c compile error due to missing s3c_rtc_setpie
RTC: Fix early irqs caused by calling rtc_set_alarm too early
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, amd: Disable GartTlbWlkErr when BIOS forgets it
x86, NUMA: Fix fakenuma boot failure
x86/mrst: Fix boot crash caused by incorrect pin to irq mapping
x86/ce4100: Add reg property to bridges
This patch disables GartTlbWlk errors on AMD Fam10h CPUs if
the BIOS forgets to do is (or is just too old). Letting
these errors enabled can cause a sync-flood on the CPU
causing a reboot.
The AMD BKDG recommends disabling GART TLB Wlk Error completely.
This patch is the fix for
https://bugzilla.kernel.org/show_bug.cgi?id=33012
on my machine.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Link: http://lkml.kernel.org/r/20110415131152.GJ18463@8bytes.org
Tested-by: Alexandre Demers <alexandre.f.demers@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Currently, numa=fake boot parameter is broken. If it's used,
kernel may panic due to devide by zero error depending on CPU
configuration
Call Trace:
[<ffffffff8104ad4c>] find_busiest_group+0x38c/0xd30
[<ffffffff81086aff>] ? local_clock+0x6f/0x80
[<ffffffff81050533>] load_balance+0xa3/0x600
[<ffffffff81050f53>] idle_balance+0xf3/0x180
[<ffffffff81550092>] schedule+0x722/0x7d0
[<ffffffff81550538>] ? wait_for_common+0x128/0x190
[<ffffffff81550a65>] schedule_timeout+0x265/0x320
[<ffffffff81095815>] ? lock_release_holdtime+0x35/0x1a0
[<ffffffff81550538>] ? wait_for_common+0x128/0x190
[<ffffffff8109bb6c>] ? __lock_release+0x9c/0x1d0
[<ffffffff815534e0>] ? _raw_spin_unlock_irq+0x30/0x40
[<ffffffff815534e0>] ? _raw_spin_unlock_irq+0x30/0x40
[<ffffffff81550540>] wait_for_common+0x130/0x190
[<ffffffff81051920>] ? try_to_wake_up+0x510/0x510
[<ffffffff8155067d>] wait_for_completion+0x1d/0x20
[<ffffffff8107f36c>] kthread_create_on_node+0xac/0x150
[<ffffffff81077bb0>] ? process_scheduled_works+0x40/0x40
[<ffffffff8155045f>] ? wait_for_common+0x4f/0x190
[<ffffffff8107a283>] __alloc_workqueue_key+0x1a3/0x590
[<ffffffff81e0cce2>] cpuset_init_smp+0x6b/0x7b
[<ffffffff81df3d07>] kernel_init+0xc3/0x182
[<ffffffff8155d5e4>] kernel_thread_helper+0x4/0x10
[<ffffffff81553cd4>] ? retint_restore_args+0x13/0x13
[<ffffffff81df3c44>] ? start_kernel+0x400/0x400
[<ffffffff8155d5e0>] ? gs_change+0x13/0x13
The divede by zero is caused by the following line,
group->cpu_power==0:
kernel/sched_fair.c::update_sg_lb_stats()
/* Adjust by relative CPU power of the group */
sgs->avg_load = (sgs->group_load * SCHED_LOAD_SCALE) / group->cpu_power;
This regression was caused by commit e23bba6044 ("x86-64, NUMA: Unify
emulated distance mapping") because it changes cpu -> node
mapping in the process of dropping fake_physnodes().
old) all cpus are assinged node 0
now) cpus are assigned round robin
(the logic is implemented by numa_init_array())
Note: The change in behavior only happens if the system doesn't
have neither ACPI SRAT table nor AMD northbridge NUMA
information.
Round robin assignment doesn't work because init_numa_sched_groups_power()
assumes all logical cpus in the same physical cpu share the same node
(then it only accounts for group_first_cpu()), and the simple round robin
breaks the above assumption.
Thus, this patch implements a reassignment of node-ids if buggy firmware
or numa emulation makes wrong cpu node map. Tt enforce all logical cpus
in the same physical cpu share the same node.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: Shaohui Zheng <shaohui.zheng@intel.com>
Cc: David Rientjes <rientjes@google.com>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Link: http://lkml.kernel.org/r/20110415203928.1303.A69D9226@jp.fujitsu.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We check if there is a domain owner for the PCI device. In case of failure
(meaning no domain has registered for this device) we make DOMID_SELF the owner.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
[v2: deal with rebasing on v2.6.37-1]
[v3: deal with rebasing on stable/irq.cleanup]
[v4: deal with rebasing on stable/irq.ween_of_nr_irqs]
[v5: deal with rebasing on v2.6.39-rc3]
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Acked-by: Xiantao Zhang <xiantao.zhang@intel.com>
When the Xen PCI backend is told to enable or disable MSI/MSI-X functions,
the initial domain performs these operations. The initial domain needs
to know which domain (guest) is going to use the PCI device so when it
makes the appropiate hypercall to retrieve the MSI/MSI-X vector it will
also assign the PCI device to the appropiate domain (guest).
This boils down to us needing a mechanism to find, set and unset the domain
id that will be using the device.
[v2: EXPORT_SYMBOL -> EXPORT_SYMBOL_GPL.]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
For future rework of try_to_wake_up() we'd like to push part of that
function onto the CPU the task is actually going to run on.
In order to do so we need a generic callback from the existing scheduler IPI.
This patch introduces such a generic callback: scheduler_ipi() and
implements it as a NOP.
BenH notes: PowerPC might use this IPI on offline CPUs under rare conditions!
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Reviewed-by: Frank Rowand <frank.rowand@am.sony.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20110405152728.744338123@chello.nl
This patch adds detection of the extended features of an
AMD IOMMU. The available features are printed to dmesg on
boot.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Moorestown systems crash on boot because the secondary CPU
clockevent (apbt1) will fail to request irq#1, which does not
have ioapic chip in its irq_desc[] entry.
Background:
Moorestown platform does not have ISA bus nor legacy IRQs. It
reuses the range of legacy IRQs for regular device interrupts.
The routing information of early system device IRQs (timers) are
obtained from firmware provided SFI tables. We reuse/fake MP
configuration table to facilitate IRQ setup with IOAPIC.
Maintaining a 1:1 mapping of IOAPIC pin (RTE entry) and IRQ#
makes routing information clean and easy to understand on
Moorestown. Though optional.
This patch allows SFI timer and vRTC IRQ to be treated as ISA
IRQ so that pin2irq mapping will be 1:1.
Also fixed MP table type and use macros to clearly set MP IRQ
entries. As a result, apbt timer and RTC interrupts on
Moorestown are within legacy IRQ range:
# cat /proc/interrupts
CPU0 CPU1
0: 11249 0 IO-APIC-edge apbt0
1: 0 12271 IO-APIC-edge apbt1
8: 887 0 IO-APIC-fasteoi dw_spi
13: 0 0 IO-APIC-fasteoi INTEL_MID_DMAC2
14: 0 0 IO-APIC-fasteoi rtc0
Further discussion of this patch can be found at:
https://lkml.org/lkml/2010/6/10/70
Suggested-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Link: http://lkml.kernel.org/r/1302286980-21139-1-git-send-email-jacob.jun.pan@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'stable/bug-fixes-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen: Allow PV-OPS kernel to detect whether XSAVE is supported
xen: just completely disable XSAVE
xen/debug: Don't be so verbose with WARN on 1-1 mapping errors.
xen: events: fix error checks in bind_*_to_irqhandler()
Make XEN_SAVE_RESTORE select HIBERNATE_CALLBACKS.
Remove XEN_SAVE_RESTORE dependency from PM_SLEEP.
Signed-off-by: Shriram Rajagopalan <rshriram@cs.ubc.ca>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
without the reg property Ben's new code won't find the PCI & ISA
bridge and the devices won't get the DT-node attached.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: davem@davemloft.net
Cc: monstr@monstr.eu
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Link: http://lkml.kernel.org/r/20110407121315.GA9204@linutronix.de
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch adds the necessary code to the AMD IOMMU driver
for enabling and disabling the ATS capability on a device
and to setup the IOMMU data structures correctly.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This patch adds a flag to the AMD IOMMU driver to indicate
that all IOMMUs present in the system support device IOTLBs.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This patch implements a function to flush the IOTLB on
devices supporting ATS and makes sure that this TLB is also
flushed if necessary.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
In order to support ATS in the AMD IOMMU driver this patch
makes sure that the generic support for ATS is compiled in.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Currently the option resides under X86_EXTENDED_PLATFORM due to historical
nonstandard A20M# handling. However that is no longer the case and so Elan can
be treated as part of the standard processor choice Kconfig option.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Link: http://lkml.kernel.org/r/1302245177.31620.47.camel@localhost.localdomain
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86-32, fpu: Fix FPU exception handling on non-SSE systems
x86, hibernate: Initialize mmu_cr4_features during boot
x86-32, NUMA: Fix ACPI NUMA init broken by recent x86-64 change
x86: visws: Fixup irq overhaul fallout
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: Clean up rebalance_domains() load-balance interval calculation
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86/mrst/vrtc: Fix boot crash in mrst_rtc_init()
rtc, x86/mrst/vrtc: Fix boot crash in rtc_read_alarm()
* 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
genirq: Fix cpumask leak in __setup_irq()
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf probe: Fix listing incorrect line number with inline function
perf probe: Fix to find recursively inlined function
perf probe: Fix multiple --vars options behavior
perf probe: Fix to remove redundant close
perf probe: Fix to ensure function declared file
The sfi_mrtc_array[] only gets initialized when the sfi mrtc
table is parsed, so the vrtc_paddr should be initalized after it
too.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1302140389-27603-1-git-send-email-feng.tang@intel.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The old code only flushed a DTE or a domain TLB before it is
actually used by the IOMMU driver. While this is efficient
and works when done right it is more likely to introduce new
bugs when changing code (which happened in the past).
This patch adds code to flush all DTEs and all domain TLBs
in each IOMMU right after it is enabled (at boot and after
resume). This reduces the complexity of the driver and makes
it less likely to introduce stale-TLB bugs in the future.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This function operates on a struct device, so give it a name
that represents that. As a side effect a new function is
introduced which operates on am iommu and a device-id. It
will be used again in a later patch.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This patch improved the handling of commands when the IOMMU
command buffer is nearly full. In this case it issues an
completion wait command and waits until the IOMMU has
processed it before continuing queuing new commands.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
These functions all operate on protection domains and not on
singe IOMMUs. Represent that in their name.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
The logic to reset the command buffer caused more problems
than it actually helped. The logic jumped in when the IOMMU
hardware doesn't execute commands anymore but the reasons
for this are usually not fixed by just resetting the command
buffer. So the code can be removed to reduce complexity.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This patch cleans up the implementation of completion-wait
command sending. It also switches the completion indicator
from the MMIO bit to a memory store which can be checked
without IOMMU locking.
As a side effect this patch makes the __iommu_queue_command
function obsolete and so it is removed too.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Now that remap allocator is cleaned up, update comments such that they
are in docbook function description format and reflect the actual
implementation.
Signed-off-by: Tejun Heo <tj@kernel.org>
Link: http://lkml.kernel.org/r/1301955840-7246-15-git-send-email-tj@kernel.org
Acked-by: Yinghai Lu <yinghai@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Remap area size can be determined from node_remap_start_vaddr[] and
node_remap_end_vaddr[] making node_remap_size[] redundant. Remove it.
While at it, make resume_map_numa_kva() use @nr_pages for number of
pages instead of @size.
Signed-off-by: Tejun Heo <tj@kernel.org>
Link: http://lkml.kernel.org/r/1301955840-7246-14-git-send-email-tj@kernel.org
Acked-by: Yinghai Lu <yinghai@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
With lowmem address reservation moved into init_alloc_remap(),
node_remap_offset[] is no longer useful. Remove it and related offset
handling code.
Signed-off-by: Tejun Heo <tj@kernel.org>
Link: http://lkml.kernel.org/r/1301955840-7246-13-git-send-email-tj@kernel.org
Acked-by: Yinghai Lu <yinghai@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
pgdat allocation is handled differnetly from other remap allocations -
it's reserved during initialization. There's no reason to handle this
any differnetly. Remap allocator is initialized for every node and if
init failed the allocation will fail and pgdat allocation can fall
back to generic code like anyone else.
Remove special init-time pgdat reservation and make allocate_pgdat()
use alloc_remap() like everyone else.
Signed-off-by: Tejun Heo <tj@kernel.org>
Link: http://lkml.kernel.org/r/1301955840-7246-12-git-send-email-tj@kernel.org
Acked-by: Yinghai Lu <yinghai@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
There's no reason to perform the actual remapping separately.
Collapse remap_numa_kva() into init_alloc_remap() and, while at it,
make it less verbose.
Signed-off-by: Tejun Heo <tj@kernel.org>
Link: http://lkml.kernel.org/r/1301955840-7246-11-git-send-email-tj@kernel.org
Acked-by: Yinghai Lu <yinghai@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Remap alloc init is done in the following stages.
1. init_alloc_remap() calculates how much memory is necessary for each
node and reserves node local memory.
2. initmem_init() collects how much each node needs and reserves a
single contiguous lowmem area which can contain all.
3. init_remap_allocator() initializes allocator parameters from the
determined lowmem address and per-node offsets.
4. Actual remap happens.
There is no reason for the lowmem remap area to be reserved as a
single contiguous area at one go. They don't interact with each other
and the memblock allocator will put them side-by-side anyway.
This patch breaks up the single lowmem address reservation and put
per-node lowmem address reservation into init_alloc_remap() and
initializes allocator parameters directly in the function as all the
addresses are determined there. This merges steps 2 and 3 into 1.
While at it, remove now largely irrelevant comments in
init_alloc_remap().
This change causes the following behavior changes.
* Remap lowmem areas are allocated in smaller per-node chunks.
* Remap lowmem area reservation failure fail future remap allocations
instead of panicking.
* Remap allocator initialization is less verbose.
Signed-off-by: Tejun Heo <tj@kernel.org>
Link: http://lkml.kernel.org/r/1301955840-7246-10-git-send-email-tj@kernel.org
Acked-by: Yinghai Lu <yinghai@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Remap allocator failure isn't fatal. The callers are required to fall
back to regular early memory allocation mechanisms on failure anyway,
so there's no reason to panic on remap init failure. Whining and
returning are enough.
Signed-off-by: Tejun Heo <tj@kernel.org>
Link: http://lkml.kernel.org/r/1301955840-7246-9-git-send-email-tj@kernel.org
Acked-by: Yinghai Lu <yinghai@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Only pgdat and memmap use remap area and there isn't much benefit in
allowing per-node override. In addition, the use of node_remap_size[]
is confusing in that it contains number of bytes before remap
initialization and then number of pages afterwards.
Move remap size calculation for memap from specific NUMA config
implementations to init_alloc_remap() and make node_remap_size[]
static.
The only behavior difference is that, before this patch, numaq_32
didn't consider max_pfn when calculating the memmap size but it's
enforced after this patch, which is the right thing to do.
Signed-off-by: Tejun Heo <tj@kernel.org>
Link: http://lkml.kernel.org/r/1301955840-7246-8-git-send-email-tj@kernel.org
Acked-by: Yinghai Lu <yinghai@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
@size variable in init_alloc_remap() is confusing in that it starts as
number of bytes as its name implies and then becomes number of pages.
Make it consistently represent bytes.
Signed-off-by: Tejun Heo <tj@kernel.org>
Link: http://lkml.kernel.org/r/1301955840-7246-7-git-send-email-tj@kernel.org
Acked-by: Yinghai Lu <yinghai@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
init_alloc_remap() is about to do more and using _kva suffix for
physical address becomes confusing because the function will be
handling both physical and virtual addresses. Rename @node_kva to
@node_pa.
This is trivial rename and doesn't cause any behavior difference.
Signed-off-by: Tejun Heo <tj@kernel.org>
Link: http://lkml.kernel.org/r/1301955840-7246-6-git-send-email-tj@kernel.org
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Separate the outer node walking loop and per-node logic from
calculate_numa_remap_pages(). The outer loop is collapsed into
initmem_init() and the per-node logic is moved into a new function -
init_alloc_remap().
The new function name is confusing with the existing
init_remap_allocator() and the behavior is the function isn't very
clean either at this point, but this is to prepare for further
cleanups and it will become prettier.
This function doesn't introduce any behavior change.
Signed-off-by: Tejun Heo <tj@kernel.org>
Link: http://lkml.kernel.org/r/1301955840-7246-5-git-send-email-tj@kernel.org
Acked-by: Yinghai Lu <yinghai@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
memblock_find_in_range() now does top-down allocation by default, so
there's no reason for its callers to explicitly implement it by
gradually lowering the start address.
Remove redundant top-down allocation logic from init_meminit() and
calculate_numa_remap_pages().
Signed-off-by: Tejun Heo <tj@kernel.org>
Link: http://lkml.kernel.org/r/1301955840-7246-4-git-send-email-tj@kernel.org
Acked-by: Yinghai Lu <yinghai@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
When pgdat is reserved in init_remap_allocator(), PAGE_SIZE aligned
size will be used. Match the size alignment in initialization to
avoid allocation failure down the road.
Signed-off-by: Tejun Heo <tj@kernel.org>
Link: http://lkml.kernel.org/r/1301955840-7246-3-git-send-email-tj@kernel.org
Acked-by: Yinghai Lu <yinghai@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
node_remap_{start|end}_vaddr[] describe [start, end) ranges; however,
alloc_remap() incorrectly failed when the current allocation + size
equaled the end but it should fail only when it goes over. Fix it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Link: http://lkml.kernel.org/r/1301955840-7246-2-git-send-email-tj@kernel.org
Acked-by: Yinghai Lu <yinghai@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Restore the initialization of mmu_cr4_features during boot, which was
removed without comment in checkin e5f15b45dd
x86: Cleanup highmap after brk is concluded
thereby breaking resume from hibernate. This restores previous
functionality in approximately the same place, and corrects the
reading of %cr4 on pre-CPUID hardware (%cr4 exists if and only if
CPUID is supported.)
However, part of the problem is that the hibernate suspend/resume
sequence should manage the save/restore of %cr4 explicitly.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Cc: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <201104020154.57136.rjw@sisk.pl>
Xen fails to mask XSAVE from the cpuid feature, despite not historically
supporting guest use of XSAVE. However, now that XSAVE support has been
added to Xen, we need to reliably detect its presence.
The most reliable way to do this is to look at the OSXSAVE feature in
cpuid which is set iff the OS (Xen, in this case), has set
CR4.OSXSAVE.
[ Cleaned up conditional a bit. - Jeremy ]
Signed-off-by: Shan Haitao <haitao.shan@intel.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Some (old) versions of Xen just kill the domain if it tries to set any
unknown bits in CR4, so we can't reliably probe for OSXSAVE in
CR4.
Since Xen doesn't support XSAVE for guests at the moment, and no such
support is being worked on, there's no downside in just unconditionally
masking XSAVE support.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
If KVM cannot find an exact match for a requested CPUID leaf, the
code will try to find the closest match instead of simply confessing
it's failure.
The implementation was meant to satisfy the CPUID specification, but
did not properly check for extended and standard leaves and also
didn't account for the index subleaf.
Beside that this rule only applies to CPUID intercepts, which is not
the only user of the kvm_find_cpuid_entry() function.
So fix this algorithm and call it from kvm_emulate_cpuid().
This fixes a crash of newer Linux kernels as KVM guests on
AMD Bulldozer CPUs, where bogus values were returned in response to
a CPUID intercept.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
When KVM scans the 0xD CPUID leaf for propagating the XSAVE save area
leaves, it assumes that the leaves are contigious and stops at the
first zero one. On AMD hardware there is a gap, though, as LWP uses
leaf 62 to announce it's state save area.
So lets iterate through all 64 possible leaves and simply skip zero
ones to also cover later features.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch reworks the processing of invalidate-pages
commands to the IOMMU. The function building the the command
is extended so we can get rid of another function. It was
also renamed to match with the other function names.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
We have a never ending stream of 'reboot quirks' for new boxes
that will not reboot properly under Linux (they will hang on
reboot).
The reason is widespread 'Windows compatible' assumption of modern
x86 hardware, which expects the following reboot sequence:
- hitting the ACPI reboot vector (if available)
- trying the keyboard controller
- hitting the ACPI reboot vector again
- then giving the keyboard controller one last go
This sequence expectation gets more and more embedded in modern
hardware, which often lacks a keyboard controller and may even
lock up if the legacy io ports are hit - and which hardware is
often not tested with Linux during development.
The end result is that reboot works under Windows-alike OSs but not
under Linux.
Rework our reboot process to meet this hardware externality a little
better and match this assumption of newer x86 hardware.
In addition to the ACPI,kbd,ACPI,kbd sequence we'll still fall
through to attempting a legacy triple fault if nothing else
works - and keep trying that and the kbd reset.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
[ this commit will also save special casing Oaktrail boards ]
Acked-by: Alan Cox <alan@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Leann Ogasawara <leann.ogasawara@canonical.com>
Cc: Dave Jones <davej@redhat.com>
Cc: Len Brown <len.brown@intel.com>
LKML-Reference: <1301939705-2404-1-git-send-email-mjg@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
There are valid situations in which this error is not
a warning. Mainly when QEMU maps a guest memory and uses
the VM_IO flag to set the MFNs. For right now make the
WARN be WARN_ONCE. In the future we will:
1). Remove the VM_IO code handling..
2). .. which will also remove this debug facility.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The linker should not be adding holes to word size aligned pointers, but
out of paranoia we are explicitly specifying that alignment. I have not
seen any holes in the jump label section in practice.
Signed-off-by: Jason Baron <jbaron@redhat.com>
LKML-Reference: <e119fbd060c9452c56063ea6148ba1070e7434cc.1300299760.git.jbaron@redhat.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Introduce:
static __always_inline bool static_branch(struct jump_label_key *key);
instead of the old JUMP_LABEL(key, label) macro.
In this way, jump labels become really easy to use:
Define:
struct jump_label_key jump_key;
Can be used as:
if (static_branch(&jump_key))
do unlikely code
enable/disale via:
jump_label_inc(&jump_key);
jump_label_dec(&jump_key);
that's it!
For the jump labels disabled case, the static_branch() becomes an
atomic_read(), and jump_label_inc()/dec() are simply atomic_inc(),
atomic_dec() operations. We show testing results for this change below.
Thanks to H. Peter Anvin for suggesting the 'static_branch()' construct.
Since we now require a 'struct jump_label_key *key', we can store a pointer into
the jump table addresses. In this way, we can enable/disable jump labels, in
basically constant time. This change allows us to completely remove the previous
hashtable scheme. Thanks to Peter Zijlstra for this re-write.
Testing:
I ran a series of 'tbench 20' runs 5 times (with reboots) for 3
configurations, where tracepoints were disabled.
jump label configured in
avg: 815.6
jump label *not* configured in (using atomic reads)
avg: 800.1
jump label *not* configured in (regular reads)
avg: 803.4
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <20110316212947.GA8792@redhat.com>
Signed-off-by: Jason Baron <jbaron@redhat.com>
Suggested-by: H. Peter Anvin <hpa@linux.intel.com>
Tested-by: David Daney <ddaney@caviumnetworks.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, UV: Fix kdump reboot
x86, amd-nb: Rename CPU PCI id define for F4
sound: Add delay.h to sound/soc/codecs/sn95031.c
x86, mtrr, pat: Fix one cpu getting out of sync during resume
x86, microcode: Unregister syscore_ops after microcode unloaded
x86: Stop including <linux/delay.h> in two asm header files
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
rcu: create new rcu_access_index() and use in mce
WARN_ON_SMP(): Add comment to explain ({0;})
check_slot() is only called from replace_intsrc_all() - which is
in the .init section.
So, put check_slot into the .init section as well, so it can be freed
after system boot.
Signed-off-by: Rakib Mullick <rakib.mullick@gmail.com>
LKML-Reference: <AANLkTing52ntzRcHkODCWDKOfRF=0uhXw5-cCUhx6M54@mail.gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Commit d8fc3afc49 (x86, NUMA: Move *_numa_init() invocations
into initmem_init()) moved acpi_numa_init() call into NUMA
initmem_init() but forgot to update 32bit NUMA init breaking ACPI
NUMA configuration for 32bit.
acpi_numa_init() call was later moved again to srat_64.c. Match
it by adding the call to get_memcfg_from_srat() in srat_32.c.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: David Rientjes <rientjes@google.com>
Cc: H. Peter Anvin <hpa@linux.intel.com>
LKML-Reference: <20110404100645.GE1420@mtj.dyndns.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In case !CONFIG_ACPI_NUMA and !CONFIG_AMD_NUMA gcc emits a warning
about the unused variable ret.
As that variable is in fact not needed I choose to remove it.
Signed-off-by: Florian Mickler <florian@mickler.org>
LKML-Reference: <1301843624-22364-1-git-send-email-florian@mickler.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
The MCE subsystem needs to sample an RCU-protected index outside of
any protection for that index. If this was a pointer, we would use
rcu_access_pointer(), but there is no corresponding rcu_access_index().
This commit therefore creates an rcu_access_index() and applies it
to MCE.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Tested-by: Zdenek Kabelac <zkabelac@redhat.com>
* Remove bogus dependency on ARCH_SELECT_MEMORY_MODEL from
ARCH_FLATMEM_ENABLE. ENABLE configs don't interfere with
SELECT_MEMORY_MODEL. They just need to indicate whether the
specific memory model is supported.
* Relocate HAVE_ARCH_ALLOC_REMAP, ARCH_PROC_KCORE_TEXT and
ARCH_SPARSEMEM_DEFAULT so that memory model related configs are
together in consistent order.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Christoph Lameter <cl@linux.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
phys_to_nid() maps physical address to NUMA node id. This is
implemented by building perfect hash in compute_hash_shift() during
initialization.
However, with SPARSE memory model, the nid is encoded in page flags.
The perfect hash implementation was for DISCONTIG memory model which
got removed years ago by b263295dbf (x86: 64-bit, make sparsemem
vmemmap the only memory model).
So, the perfect hash ends up being used only during initialization
when the core SPARSE code already provides perfectly acceptable
generic early_pfn_to_nid() implementation.
Drop phys_to_nid() and use the generic ealry_pfn_to_nid() instead.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Christoph Lameter <cl@linux-foundation.org>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
After a crash dump on an SGI Altix UV system the crash kernel
fails to cause a reboot. EFI mode is disabled in the kdump
kernel, so only the reboot_type of BOOT_ACPI works.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Cc: rja@sgi.com
LKML-Reference: <E1Q5Iuo-00013b-UK@eag09.americas.sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
With increasing number of PCI function ids, add the PCI function
id in the define name instead of its symbolic name in the BKDG
for more clarity. This renames function 4 define.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
LKML-Reference: <20110330183447.GA3668@aftab>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
On laptops with core i5/i7, there were reports that after resume
graphics workloads were performing poorly on a specific AP, while
the other cpu's were ok. This was observed on a 32bit kernel
specifically.
Debug showed that the PAT init was not happening on that AP
during resume and hence it contributing to the poor workload
performance on that cpu.
On this system, resume flow looked like this:
1. BP starts the resume sequence and we reinit BP's MTRR's/PAT
early on using mtrr_bp_restore()
2. Resume sequence brings all AP's online
3. Resume sequence now kicks off the MTRR reinit on all the AP's.
4. For some reason, between point 2 and 3, we moved from BP
to one of the AP's. My guess is that printk() during resume
sequence is contributing to this. We don't see similar
behavior with the 64bit kernel but there is no guarantee that
at this point the remaining resume sequence (after AP's bringup)
has to happen on BP.
5. set_mtrr() was assuming that we are still on BP and skipped the
MTRR/PAT init on that cpu (because of 1 above)
6. But we were on an AP and this led to not reprogramming PAT
on this cpu leading to bad performance.
Fix this by doing unconditional mtrr_if->set_all() in set_mtrr()
during MTRR/PAT init. This might be unnecessary if we are still
running on BP. But it is of no harm and will guarantee that after
resume, all the cpu's will be in sync with respect to the
MTRR/PAT registers.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <1301438292-28370-1-git-send-email-eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
Tested-by: Keith Packard <keithp@keithp.com>
Cc: stable@kernel.org [v2.6.32+]
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
The lonely user of the internal interface was not in the coccinelle
script.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix section mismatch warnings:
set_phys_range_identity() is called by __init xen_set_identity(),
so also mark set_phys_range_identity() as __init.
then:
__early_alloc_p2m() is called set_phys_range_identity(), so also mark
__early_alloc_p2m() as __init.
WARNING: arch/x86/built-in.o(.text+0x7856): Section mismatch in reference from the function __early_alloc_p2m() to the function .init.text:extend_brk()
The function __early_alloc_p2m() references
the function __init extend_brk().
This is often because __early_alloc_p2m lacks a __init
annotation or the annotation of extend_brk is wrong.
WARNING: arch/x86/built-in.o(.text+0x7967): Section mismatch in reference from the function set_phys_range_identity() to the function .init.text:extend_brk()
The function set_phys_range_identity() references
the function __init extend_brk().
This is often because set_phys_range_identity lacks a __init
annotation or the annotation of extend_brk is wrong.
[v2: Per Stephen Hemming recommonedation made __early_alloc_p2m static]
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Currently, microcode doesn't unregister syscore_ops after it's
unloaded. So if we modprobe then rmmod microcode, the stale
microcode syscore_ops info will stay on syscore_ops_list.
Later when we're trying to reboot/halt/shutdown the machine, kernel
will panic on syscore_shutdown().
With the patch applied, I can reboot/halt/shutdown my machine successfully.
Signed-off-by: Xiaotian Feng <dfeng@redhat.com>
Cc: Tigran Aivazian <tigran@aivazian.fsnet.co.uk>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
LKML-Reference: <1301387672-23661-1-git-send-email-dfeng@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
It is more effective to use a segment prefix instead of calculating the
address of the current cpu area amd then testing flags.
Signed-off-by: Christoph Lameter <cl@linux.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Add this_cpu_has() which determines if the current cpu has a certain
ability using a segment prefix and a bit test operation.
For that we need to add bit operations to x86s percpu.h.
Many uses of cpu_has use a pointer passed to a function to determine
the current flags. That is no longer necessary after this patch.
However, this patch only converts the straightforward cases where
cpu_has is used with this_cpu_ptr. The rest is work for later.
-tj: Rolled up patch to add x86_ prefix and use percpu_read() instead
of percpu_read_stable().
Signed-off-by: Christoph Lameter <cl@linux.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Stop including <linux/delay.h> in x86 header files which don't
need it. This will let the compiler complain when this header is
not included by source files when it should, so that
contributors can fix the problem before building on other
architectures starts to fail.
Credits go to Geert for the idea.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: James E.J. Bottomley <James.Bottomley@suse.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
LKML-Reference: <20110325152014.297890ec@endymion.delvare>
[ this also fixes an upstream build bug in drivers/media/rc/ite-cir.c ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
No change on the functional level, just align the table properly.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Lin Ming <ming.m.lin@intel.com>
LKML-Reference: <4D8FA213.5050108@openvz.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Omit the segment prefix in the UP case. GS is not used then
and we will generate segfaults if cmpxchg16b is used otherwise.
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes problem with packets that are not multiple of 64bytes.
Signed-off-by: Adrian Hoban <adrian.hoban@intel.com>
Signed-off-by: Aidan O'Mahony <aidan.o.mahony@intel.com>
Signed-off-by: Gabriele Paoloni <gabriele.paoloni@intel.com>
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The cs5535-pms cell doesn't actually need to be cloned, so we can drop that
and simply have the olpc-xo1.c driver use "cs5535-pms" directly.
Also, rename the cs5535-acpi clones to what we actually use for the (currently
out-of-tree) SCI driver. In the process, that fixes a subtle bug in
olpc-xo1.c which broke powerdown on XO-1s.. olpc-xo1-ac-acpi was a typo, not
something that actually existed.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Replace mfd_shared_platform_driver_register with mfd_clone_cell. The
former was called by an mfd client, and registered both a platform driver
and device. The latter is called by an mfd driver, and registers only a
platform device.
The downside of this is that mfd drivers need to be modified whenever
new clients are added that share a cell; the upside is that it fits
Linux's driver model better. It's also simpler.
This also converts cs5535-mfd/olpc-xo1 from the old API. cs5535-mfd
now creates the olpc-xo1-{acpi,pms} devices, while olpc-xo1 binds to
them via platform drivers.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* 'syscore' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
Introduce ARCH_NO_SYSDEV_OPS config option (v2)
cpufreq: Use syscore_ops for boot CPU suspend/resume (v2)
KVM: Use syscore_ops instead of sysdev class and sysdev
PCI / Intel IOMMU: Use syscore_ops instead of sysdev class and sysdev
timekeeping: Use syscore_ops instead of sysdev class and sysdev
x86: Use syscore_ops instead of sysdev classes and sysdevs
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb:
kdb: add usage string of 'per_cpu' command
kgdb,x86_64: fix compile warning found with sparse
kdb: code cleanup to use macro instead of value
kgdboc,kgdbts: strlen() doesn't count the terminator
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf, x86: Complain louder about BIOSen corrupting CPU/PMU state and continue
perf, x86: P4 PMU - Read proper MSR register to catch unflagged overflows
perf symbols: Look at .dynsym again if .symtab not found
perf build-id: Add quirk to deal with perf.data file format breakage
perf session: Pass evsel in event_ops->sample()
perf: Better fit max unprivileged mlock pages for tools needs
perf_events: Fix stale ->cgrp pointer in update_cgrp_time_from_cpuctx()
perf top: Fix uninitialized 'counter' variable
tracing: Fix set_ftrace_filter probe function display
perf, x86: Fix Intel fixed counters base initialization
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
futex: Fix WARN_ON() test for UP
WARN_ON_SMP(): Allow use in if() statements on UP
x86, dumpstack: Use %pB format specifier for stack trace
vsprintf: Introduce %pB format specifier
lockdep: Remove unused 'factor' variable from lockdep_stats_show()
Fix sparse warning:
arch/x86/kernel/kgdb.c:123:9: warning: switch with no cases
Reported-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Eric Dumazet reported that hardware PMU events do not work on his
system, due to the BIOS corrupting PMU state:
Performance Events: PEBS fmt0+, Core2 events, Broken BIOS detected, using software events only.
[Firmware Bug]: the BIOS has corrupted hw-PMU resources (MSR 186 is 43003c)
Linus suggested that we continue in the face of such BIOS-induced CPU
state corruption:
http://lkml.org/lkml/2011/3/24/608
Such BIOSes will have to be fixed - Linux developers rely on a working and
fully capable PMU and the BIOS interfering with the CPU's PMU state is simply
not acceptable.
So this patch changes perf to continue when it detects such BIOS
interaction, some hardware events may be unreliable due to the BIOS
writing and re-writing them - there's not much the kernel can do
about that but to detect the corruption and report it.
Reported-and-tested-by: Eric Dumazet <eric.dumazet@gmail.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Steven Rostedt <rostedt@goodmis.org>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
That call escaped the name space cleanup. Fix it up.
We really want to call there. The chip might have changed since the
irq was setup initially. So let the core code and the chip decide what
to do. The status is just an unreliable snapshot.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
The xlate() function returns 0 or a negative error code. Returning the
error code blindly will be seen as an huge irq number by the calling
function because irq_create_of_mapping() returns an unsigned value.
Return 0 (NO_IRQ) as required.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
The read of a proper MSR register was missed and instead of
counter the configration register was tested (it has
ARCH_P4_UNFLAGGED_BIT always cleared) leading to unknown NMI
hitting the system. As result the user may obtain "Dazed and
confused, but trying to continue" message. Fix it by reading a
proper MSR register.
When an NMI happens on a P4, the perf nmi handler checks the
configuration register to see if the overflow bit is set or not
before taking appropriate action. Unfortunately, various P4
machines had a broken overflow bit, so a backup mechanism was
implemented. This mechanism checked to see if the counter
rolled over or not.
A previous commit that implemented this backup mechanism was
broken. Instead of reading the counter register, it used the
configuration register to determine if the counter rolled over
or not. Reading that bit would give incorrect results.
This would lead to 'Dazed and confused' messages for the end
user when using the perf tool (or if the nmi watchdog is
running).
The fix is to read the counter register before determining if
the counter rolled over or not.
Signed-off-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Lin Ming <ming.m.lin@intel.com>
LKML-Reference: <4D8BAB49.3080701@openvz.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
For some performance events it's useful to set the EDGE and INV
bits and the CMASK mask in the counter control register. The list
of predefined events Intel releases for each CPU has some events which
require these settings to get more "natural" to use higher level events.
oprofile currently doesn't allow this.
This patch adds new extra configuration fields for them, so that
they can be specified in oprofilefs.
An updated oprofile daemon can then make use of this to set them.
v2: Write back masked extra value to variable.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Robert Richter <robert.richter@amd.com>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (42 commits)
ACPI: minor printk format change in acpi_pad
ACPI: make acpi_pad /sys output more readable
ACPICA: Update version to 20110316
ACPICA: Header support for SLIC table
ACPI: Make sure the FADT is at least rev 2 before using the reset register
ACPI: Bug compatibility for Windows on the ACPI reboot vector
ACPICA: Fix access width for reset vector
ACPI battery: fribble sysfs files from a resume notifier
ACPI button: remove unused procfs I/F
ACPI, APEI, Add PCIe AER error information printing support
PCIe, AER, use pre-generated prefix in error information printing
ACPI, APEI, Add ERST record ID cache
ACPI: Use syscore_ops instead of sysdev class and sysdev
ACPI: Remove the unused EC sysdev class
ACPI: use __cpuinit for the acpi_processor_set_pdc() call tree
ACPI: use __init where possible in processor driver
Thermal_Framework-Fix_crash_during_hwmon_unregister
ACPICA: Update version to 20110211.
ACPICA: Add mechanism to defer _REG methods for some installed handlers
ACPICA: Add support for FunctionalFixedHW in acpi_ut_get_region_name
...
It is possible to add a p2m override on pages that are currently mapped
to INVALID_P2M_ENTRY; in particular, this will happen when using
ballooned pages in gntdev. This means that set_phys_to_machine must be
used instead of __set_phys_to_machine.
Signed-off-by: Daniel De Graaf <dgdegra@tycho.nsa.gov>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
'ret' isn't used by check_slot(), gets initialized but has no real use,
so remove it.
Signed-off-by: Rakib Mullick <rakib.mullick@gmail.com>
LKML-Reference: <AANLkTikh3y+is3xixKBdyHhr_cHxzPFJF729Fcvt8+Ns@mail.gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
deal with races in /proc/*/{syscall,stack,personality}
proc: enable writing to /proc/pid/mem
proc: make check_mem_permission() return an mm_struct on success
proc: hold cred_guard_mutex in check_mem_permission()
proc: disable mem_write after exec
mm: implement access_remote_vm
mm: factor out main logic of access_process_vm
mm: use mm_struct to resolve gate vma's in __get_user_pages
mm: arch: rename in_gate_area_no_task to in_gate_area_no_mm
mm: arch: make in_gate_area take an mm_struct instead of a task_struct
mm: arch: make get_gate_vma take an mm_struct instead of a task_struct
x86: mark associated mm when running a task in 32 bit compatibility mode
x86: add context tag to mark mm when running a task in 32-bit compatibility mode
auxv: require the target to be tracable (or yourself)
close race in /proc/*/environ
report errors in /proc/*/*map* sanely
pagemap: close races with suid execve
make sessionid permissions in /proc/*/task/* match those in /proc/*
fix leaks in path_lookupat()
Fix up trivial conflicts in fs/proc/base.c
The Xen PV drivers in a crashed HVM guest can not connect to the dom0
backend drivers because both frontend and backend drivers are still in
connected state. To run the connection reset function only in case of a
crashdump, the is_kdump_kernel() function needs to be available for the PV
driver modules.
Consolidate elfcorehdr_addr, setup_elfcorehdr and saved_max_pfn into
kernel/crash_dump.c Also export elfcorehdr_addr to make is_kdump_kernel()
usable for modules.
Leave 'elfcorehdr' as early_param(). This changes powerpc from __setup()
to early_param(). It adds an address range check from x86 also on ia64
and powerpc.
[akpm@linux-foundation.org: additional #includes]
[akpm@linux-foundation.org: remove elfcorehdr_addr export]
[akpm@linux-foundation.org: fix for Tejun's mm/nobootmem.c changes]
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is no user now.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: David Miller <davem@davemloft.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
1. Add an option to include RapidIO support if the PCI is available.
2. Add FSL_RIO configuration option to enable controller selection.
3. Add RapidIO support option into x86 and MIPS architectures.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Cc: Micha Nelissen <micha@neli.hopto.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
minix bit operations are only used by minix filesystem and useless by
other modules. Because byte order of inode and block bitmaps is different
on each architecture like below:
m68k:
big-endian 16bit indexed bitmaps
h8300, microblaze, s390, sparc, m68knommu:
big-endian 32 or 64bit indexed bitmaps
m32r, mips, sh, xtensa:
big-endian 32 or 64bit indexed bitmaps for big-endian mode
little-endian bitmaps for little-endian mode
Others:
little-endian bitmaps
In order to move minix bit operations from asm/bitops.h to architecture
independent code in minix filesystem, this provides two config options.
CONFIG_MINIX_FS_BIG_ENDIAN_16BIT_INDEXED is only selected by m68k.
CONFIG_MINIX_FS_NATIVE_ENDIAN is selected by the architectures which use
native byte order bitmaps (h8300, microblaze, s390, sparc, m68knommu,
m32r, mips, sh, xtensa). The architectures which always use little-endian
bitmaps do not select these options.
Finally, we can remove minix bit operations from asm/bitops.h for all
architectures.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Michal Simek <monstr@monstr.eu>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Cc: Chris Zankel <chris@zankel.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As the result of conversions, there are no users of ext2 non-atomic bit
operations except for ext2 filesystem itself. Now we can put them into
architecture independent code in ext2 filesystem, and remove from
asm/bitops.h for all architectures.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Jan Kara <jack@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce little-endian bit operations to the big-endian architectures
which do not have native little-endian bit operations and the
little-endian architectures. (alpha, avr32, blackfin, cris, frv, h8300,
ia64, m32r, mips, mn10300, parisc, sh, sparc, tile, x86, xtensa)
These architectures can just include generic implementation
(asm-generic/bitops/le.h).
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Mikael Starvik <starvik@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Matthew Wilcox <willy@debian.org>
Cc: Grant Grundler <grundler@parisc-linux.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Zankel <chris@zankel.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce Kconfig option allowing architectures where sysdev
operations used during system suspend, resume and shutdown have been
completely replaced with struct sycore_ops operations to avoid
building sysdev code that will never be used.
Make callbacks in struct sys_device and struct sysdev_driver depend
on ARCH_NO_SYSDEV_OPS to allows us to verify if all of the references
have been actually removed from the code the given architecture
depends on.
Make x86 select ARCH_NO_SYSDEV_OPS.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Some subsystems in the x86 tree need to carry out suspend/resume and
shutdown operations with one CPU on-line and interrupts disabled and
they define sysdev classes and sysdevs or sysdev drivers for this
purpose. This leads to unnecessarily complicated code and excessive
memory usage, so switch them to using struct syscore_ops objects for
this purpose instead.
Generally, there are three categories of subsystems that use
sysdevs for implementing PM operations: (1) subsystems whose
suspend/resume callbacks ignore their arguments entirely (the
majority), (2) subsystems whose suspend/resume callbacks use their
struct sys_device argument, but don't really need to do that,
because they can be implemented differently in an arguably simpler
way (io_apic.c), and (3) subsystems whose suspend/resume callbacks
use their struct sys_device argument, but the value of that argument
is always the same and could be ignored (microcode_core.c). In all
of these cases the subsystems in question may be readily converted to
using struct syscore_ops objects for power management and shutdown.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Now that gate vma's are referenced with respect to a particular mm and not a
particular task it only makes sense to propagate the change to this predicate as
well.
Signed-off-by: Stephen Wilson <wilsons@start.ca>
Reviewed-by: Michel Lespinasse <walken@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Morally, the question of whether an address lies in a gate vma should be asked
with respect to an mm, not a particular task. Moreover, dropping the dependency
on task_struct will help make existing and future operations on mm's more
flexible and convenient.
Signed-off-by: Stephen Wilson <wilsons@start.ca>
Reviewed-by: Michel Lespinasse <walken@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Morally, the presence of a gate vma is more an attribute of a particular mm than
a particular task. Moreover, dropping the dependency on task_struct will help
make both existing and future operations on mm's more flexible and convenient.
Signed-off-by: Stephen Wilson <wilsons@start.ca>
Reviewed-by: Michel Lespinasse <walken@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This patch simply follows the same practice as for setting the TIF_IA32 flag.
In particular, an mm is marked as holding 32-bit tasks when a 32-bit binary is
exec'ed. Both ELF and a.out formats are updated.
Signed-off-by: Stephen Wilson <wilsons@start.ca>
Reviewed-by: Michel Lespinasse <walken@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This tag is intended to mirror the thread info TIF_IA32 flag. Will be used to
identify mm's which support 32 bit tasks running in compatibility mode without
requiring a reference to the task itself.
Signed-off-by: Stephen Wilson <wilsons@start.ca>
Reviewed-by: Michel Lespinasse <walken@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
As requested by Samuel, there's not really any reason to have "shared"
in the name.
This also modifies the only user of the function, as well.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This enables sharing of cs5535-mfd cells via the new mfd_shared_* API.
Hooks for enable/disble of resources are added, with refcounting of
resources being automatically handled so that cs5535_mfd_res_enable/disable
are only called when necessary.
Clients of cs5535-mfd (in this case, olpc-xo1.c) are also modified to
use the mfd_shared API. The platform drivers are also renamed to
olpc-xo1-{pms,acpi}, and resource enabling/disabling is replaced
with mfd_shared API calls.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Not all 64-bit systems require ISA-style DMA, so allow it to be
configurable. x86 utilizes the generic ISA DMA allocator from
kernel/dma.c, so require it only when CONFIG_ISA_DMA_API is enabled.
Disabling CONFIG_ISA_DMA_API is dependent on x86_64 since those machines
do not have ISA slots and benefit the most from disabling the option (and
on CONFIG_EXPERT as required by H. Peter Anvin).
When disabled, this also avoids declaring claim_dma_lock(),
release_dma_lock(), request_dma(), and free_dma() since those interfaces
will no longer be provided.
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The generic floppy disk driver utilizies the interface provided by
CONFIG_ISA_DMA_API, specifically claim_dma_lock(), release_dma_lock(),
request_dma(), and free_dma(). Thus, there's a strict dependency on the
config option and the driver should only be loaded if the kernel supports
ISA-style DMA.
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
8237A utilizes the interface provided by CONFIG_ISA_DMA_API, specifically
claim_dma_lock() and release_dma_lock(). Thus, there's a strict
dependency on the config option and the module should only be loaded if
the kernel supports ISA-style DMA.
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The oops=panic cmdline option is not x86 specific, move it to generic code.
Update documentation.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All architectures can use the common dma_addr_t typedef now. We can
remove the arch specific dma_addr_t.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Matt Turner <mattst88@gmail.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a node parameter to alloc_thread_info(), and change its name to
alloc_thread_info_node()
This change is needed to allow NUMA aware kthread_create_on_cpu()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Tejun Heo <tj@kernel.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: David Howells <dhowells@redhat.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
xen: update mask_rw_pte after kernel page tables init changes
xen: set max_pfn_mapped to the last pfn mapped
x86: Cleanup highmap after brk is concluded
Fix up trivial onflict (added header file includes) in
arch/x86/mm/init_64.c
When CONFIG_X86_MPPARSE=y and CONFIG_X86_IO_APIC=n, then we get
the following warning:
arch/x86/kernel/mpparse.c:723: warning: 'check_slot' defined but not used
So, put check_slot into CONFIG_X86_IO_APIC context. Its only
called from CONFIG_X86_IO_APIC=y context.
Signed-off-by: Rakib Mullick <rakib.mullick@gmail.com>
LKML-Reference: <AANLkTinsUfGc=NG_GeH_B+zFVu+DXJzZbJKdQLscqfuH@mail.gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
APEI ERST firmware interface and implementation has no multiple users
in mind. For example, if there is four records in storage with ID: 1,
2, 3 and 4, if two ERST readers enumerate the records via
GET_NEXT_RECORD_ID as follow,
reader 1 reader 2
1
2
3
4
-1
-1
where -1 signals there is no more record ID.
Reader 1 has no chance to check record 2 and 4, while reader 2 has no
chance to check record 1 and 3. And any other GET_NEXT_RECORD_ID will
return -1, that is, other readers will has no chance to check any
record even they are not cleared by anyone.
This makes raw GET_NEXT_RECORD_ID not suitable for used by multiple
users.
To solve the issue, an in-memory ERST record ID cache is designed and
implemented. When enumerating record ID, the ID returned by
GET_NEXT_RECORD_ID is added into cache in addition to be returned to
caller. So other readers can check the cache to get all record ID
available.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
It is frequently useful to sync a single file system, instead of all
mounted file systems via sync(2):
- On machines with many mounts, it is not at all uncommon for some of
them to hang (e.g. unresponsive NFS server). sync(2) will get stuck on
those and may never get to the one you do care about (e.g., /).
- Some applications write lots of data to the file system and then
want to make sure it is flushed to disk. Calling fsync(2) on each
file introduces unnecessary ordering constraints that result in a large
amount of sub-optimal writeback/flush/commit behavior by the file
system.
There are currently two ways (that I know of) to sync a single super_block:
- BLKFLSBUF ioctl on the block device: That also invalidates the bdev
mapping, which isn't usually desirable, and doesn't work for non-block
file systems.
- 'mount -o remount,rw' will call sync_filesystem as an artifact of the
current implemention. Relying on this little-known side effect for
something like data safety sounds foolish.
Both of these approaches require root privileges, which some applications
do not have (nor should they need?) given that sync(2) is an unprivileged
operation.
This patch introduces a new system call syncfs(2) that takes an fd and
syncs only the file system it references. Maybe someday we can
$ sync /some/path
and not get
sync: ignoring all arguments
The syscall is motivated by comments by Al and Christoph at the last LSF.
syncfs(2) seems like an appropriate name given statfs(2).
A similar ioctl was also proposed a while back, see
http://marc.info/?l=linux-fsdevel&m=127970513829285&w=2
Signed-off-by: Sage Weil <sage@newdream.net>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
After "x86-64, mm: Put early page table high" already existing kernel
page table pages can be mapped using early_ioremap too so we need to
update mask_rw_pte to make sure these pages are still mapped RO.
The reason why we have to do that is explain by the commit message of
fef5ba797991f9335bcfc295942b684f9bf613a1:
"Xen requires that all pages containing pagetable entries to be mapped
read-only. If pages used for the initial pagetable are already mapped
then we can change the mapping to RO. However, if they are initially
unmapped, we need to make sure that when they are later mapped, they
are also mapped RO.
..SNIP..
the pagetable setup code early_ioremaps the pages to write their
entries, so we must make sure that mappings created in the early_ioremap
fixmap area are mapped RW. (Those mappings are removed before the pages
are presented to Xen as pagetable pages.)"
We accomplish all this in mask_rw_pte by mapping RO all the pages mapped
using early_ioremap apart from the last one that has been allocated
because it is not a page table page yet (it has not been hooked into the
page tables yet).
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
LKML-Reference: <alpine.DEB.2.00.1103171739050.3382@kaball-desktop>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Do not set max_pfn_mapped to the end of the initial memory mappings,
that also contain pages that don't belong in pfn space (like the mfn
list).
Set max_pfn_mapped to the last real pfn mapped in the initial memory
mappings that is the pfn backing _end.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
LKML-Reference: <alpine.DEB.2.00.1103171739050.3382@kaball-desktop>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Now cleanup_highmap actually is in two steps: one is early in head64.c
and only clears above _end; a second one is in init_memory_mapping() and
tries to clean from _brk_end to _end.
It should check if those boundaries are PMD_SIZE aligned but currently
does not.
Also init_memory_mapping() is called several times for numa or memory
hotplug, so we really should not handle initial kernel mappings there.
This patch moves cleanup_highmap() down after _brk_end is settled so
we can do everything in one step.
Also we honor max_pfn_mapped in the implementation of cleanup_highmap.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
LKML-Reference: <alpine.DEB.2.00.1103171739050.3382@kaball-desktop>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The following patch solves the problems introduced by Robert's
commit 41bf498 and reported by Arun Sharma. This commit gets rid
of the base + index notation for reading and writing PMU msrs.
The problem is that for fixed counters, the new calculation for
the base did not take into account the fixed counter indexes,
thus all fixed counters were read/written from fixed counter 0.
Although all fixed counters share the same config MSR, they each
have their own counter register.
Without:
$ task -e unhalted_core_cycles -e instructions_retired -e baclears noploop 1 noploop for 1 seconds
242202299 unhalted_core_cycles (0.00% scaling, ena=1000790892, run=1000790892)
2389685946 instructions_retired (0.00% scaling, ena=1000790892, run=1000790892)
49473 baclears (0.00% scaling, ena=1000790892, run=1000790892)
With:
$ task -e unhalted_core_cycles -e instructions_retired -e baclears noploop 1 noploop for 1 seconds
2392703238 unhalted_core_cycles (0.00% scaling, ena=1000840809, run=1000840809)
2389793744 instructions_retired (0.00% scaling, ena=1000840809, run=1000840809)
47863 baclears (0.00% scaling, ena=1000840809, run=1000840809)
Signed-off-by: Stephane Eranian <eranian@google.com>
Cc: peterz@infradead.org
Cc: ming.m.lin@intel.com
Cc: robert.richter@amd.com
Cc: asharma@fb.com
Cc: perfmon2-devel@lists.sf.net
LKML-Reference: <20110319172005.GB4978@quad>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: label: remove #include of ACPI header to avoid warnings
PCI: label: Fix compilation error when CONFIG_ACPI is unset
PCI: pre-allocate additional resources to devices only after successful allocation of essential resources.
PCI: introduce reset_resource()
PCI: data structure agnostic free list function
PCI: refactor io size calculation code
PCI: do not create quirk I/O regions below PCIBIOS_MIN_IO for ICH
PCI hotplug: acpiphp: set current_state to D0 in register_slot
PCI: Export ACPI _DSM provided firmware instance number and string name to sysfs
PCI: add more checking to ICH region quirks
PCI: aer-inject: Override PCIe AER Mask Registers
PCI: fix tlan build when CONFIG_PCI is not enabled
PCI: remove quirk for pre-production systems
PCI: Avoid potential NULL pointer dereference in pci_scan_bridge
PCI/lpc: irq and pci_ids patch for Intel DH89xxCC DeviceIDs
PCI: sysfs: Fix failure path for addition of "vpd" attribute
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Flush TLB if PGD entry is changed in i386 PAE mode
x86, dumpstack: Correct stack dump info when frame pointer is available
x86: Clean up csum-copy_64.S a bit
x86: Fix common misspellings
x86: Fix misspelling and align params
x86: Use PentiumPro-optimized partial_csum() on VIA C7
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (30 commits)
trace, filters: Initialize the match variable in process_ops() properly
trace, documentation: Fix branch profiling location in debugfs
oprofile, s390: Cleanups
oprofile, s390: Remove hwsampler_files.c and merge it into init.c
perf: Fix tear-down of inherited group events
perf: Reorder & optimize perf_event_context to remove alignment padding on 64 bit builds
perf: Handle stopped state with tracepoints
perf: Fix the software events state check
perf, powerpc: Handle events that raise an exception without overflowing
perf, x86: Use INTEL_*_CONSTRAINT() for all PEBS event constraints
perf, x86: Clean up SandyBridge PEBS events
perf lock: Fix sorting by wait_min
perf tools: Version incorrect with some versions of grep
perf evlist: New command to list the names of events present in a perf.data file
perf script: Add support for H/W and S/W events
perf script: Add support for dumping symbols
perf script: Support custom field selection for output
perf script: Move printing of 'common' data from print_event and rename
perf tracing: Remove print_graph_cpu and print_graph_proc from trace-event-parse
perf script: Change process_event prototype
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (47 commits)
doc: CONFIG_UNEVICTABLE_LRU doesn't exist anymore
Update cpuset info & webiste for cgroups
dcdbas: force SMI to happen when expected
arch/arm/Kconfig: remove one to many l's in the word.
asm-generic/user.h: Fix spelling in comment
drm: fix printk typo 'sracth'
Remove one to many n's in a word
Documentation/filesystems/romfs.txt: fixing link to genromfs
drivers:scsi Change printk typo initate -> initiate
serial, pch uart: Remove duplicate inclusion of linux/pci.h header
fs/eventpoll.c: fix spelling
mm: Fix out-of-date comments which refers non-existent functions
drm: Fix printk typo 'failled'
coh901318.c: Change initate to initiate.
mbox-db5500.c Change initate to initiate.
edac: correct i82975x error-info reported
edac: correct i82975x mci initialisation
edac: correct commented info
fs: update comments to point correct document
target: remove duplicate include of target/target_core_device.h from drivers/target/target_core_hba.c
...
Trivial conflict in fs/eventpoll.c (spelling vs addition)
According to intel CPU manual, every time PGD entry is changed in i386 PAE
mode, we need do a full TLB flush. Current code follows this and there is
comment for this too in the code.
But current code misses the multi-threaded case. A changed page table
might be used by several CPUs, every such CPU should flush TLB. Usually
this isn't a problem, because we prepopulate all PGD entries at process
fork. But when the process does munmap and follows new mmap, this issue
will be triggered.
When it happens, some CPUs keep doing page faults:
http://marc.info/?l=linux-kernel&m=129915020508238&w=2
Reported-by: Yasunori Goto<y-goto@jp.fujitsu.com>
Tested-by: Yasunori Goto<y-goto@jp.fujitsu.com>
Reviewed-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Shaohua Li<shaohua.li@intel.com>
Cc: Mallick Asit K <asit.k.mallick@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-mm <linux-mm@kvack.org>
Cc: stable <stable@kernel.org>
LKML-Reference: <1300246649.2337.95.camel@sli10-conroe>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Current stack dump code scans entire stack and check each entry
contains a pointer to kernel code. If CONFIG_FRAME_POINTER=y it
could mark whether the pointer is valid or not based on value of
the frame pointer. Invalid entries could be preceded by '?' sign.
However this was not going to happen because scan start point
was always higher than the frame pointer so that they could not
meet.
Commit 9c0729dc80 ("x86: Eliminate bp argument from the stack
tracing routines") delayed bp acquisition point, so the bp was
read in lower frame, thus all of the entries were marked
invalid.
This patch fixes this by reverting above commit while retaining
stack_frame() helper as suggested by Frederic Weisbecker.
End result looks like below:
before:
[ 3.508329] Call Trace:
[ 3.508551] [<ffffffff814f35c9>] ? panic+0x91/0x199
[ 3.508662] [<ffffffff814f3739>] ? printk+0x68/0x6a
[ 3.508770] [<ffffffff81a981b2>] ? mount_block_root+0x257/0x26e
[ 3.508876] [<ffffffff81a9821f>] ? mount_root+0x56/0x5a
[ 3.508975] [<ffffffff81a98393>] ? prepare_namespace+0x170/0x1a9
[ 3.509216] [<ffffffff81a9772b>] ? kernel_init+0x1d2/0x1e2
[ 3.509335] [<ffffffff81003894>] ? kernel_thread_helper+0x4/0x10
[ 3.509442] [<ffffffff814f6880>] ? restore_args+0x0/0x30
[ 3.509542] [<ffffffff81a97559>] ? kernel_init+0x0/0x1e2
[ 3.509641] [<ffffffff81003890>] ? kernel_thread_helper+0x0/0x10
after:
[ 3.522991] Call Trace:
[ 3.523351] [<ffffffff814f35b9>] panic+0x91/0x199
[ 3.523468] [<ffffffff814f3729>] ? printk+0x68/0x6a
[ 3.523576] [<ffffffff81a981b2>] mount_block_root+0x257/0x26e
[ 3.523681] [<ffffffff81a9821f>] mount_root+0x56/0x5a
[ 3.523780] [<ffffffff81a98393>] prepare_namespace+0x170/0x1a9
[ 3.523885] [<ffffffff81a9772b>] kernel_init+0x1d2/0x1e2
[ 3.523987] [<ffffffff81003894>] kernel_thread_helper+0x4/0x10
[ 3.524228] [<ffffffff814f6880>] ? restore_args+0x0/0x30
[ 3.524345] [<ffffffff81a97559>] ? kernel_init+0x0/0x1e2
[ 3.524445] [<ffffffff81003890>] ? kernel_thread_helper+0x0/0x10
-v5:
* fix build breakage with oprofile
-v4:
* use 0 instead of regs->bp
* separate out printk changes
-v3:
* apply comment from Frederic
* add a couple of printk fixes
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Soren Sandmann <ssp@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Robert Richter <robert.richter@amd.com>
LKML-Reference: <1300416006-3163-1-git-send-email-namhyung@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The many stray whitespaces and other uncleanlinesses made this code
almost unreadable to me - so fix those.
No changes to the code.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
They were generated by 'codespell' and then manually reviewed.
Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Cc: trivial@kernel.org
LKML-Reference: <1300389856-1099-3-git-send-email-lucas.demarchi@profusion.mobi>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'kvm-updates/2.6.39' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (55 commits)
KVM: unbreak userspace that does not sets tss address
KVM: MMU: cleanup pte write path
KVM: MMU: introduce a common function to get no-dirty-logged slot
KVM: fix rcu usage in init_rmode_* functions
KVM: fix kvmclock regression due to missing clock update
KVM: emulator: Fix permission checking in io permission bitmap
KVM: emulator: Fix io permission checking for 64bit guest
KVM: SVM: Load %gs earlier if CONFIG_X86_32_LAZY_GS=n
KVM: x86: Remove useless regs_page pointer from kvm_lapic
KVM: improve comment on rcu use in irqfd_deassign
KVM: MMU: remove unused macros
KVM: MMU: cleanup page alloc and free
KVM: MMU: do not record gfn in kvm_mmu_pte_write
KVM: MMU: move mmu pages calculated out of mmu lock
KVM: MMU: set spte accessed bit properly
KVM: MMU: fix kvm_mmu_slot_remove_write_access dropping intermediate W bits
KVM: Start lock documentation
KVM: better readability of efer_reserved_bits
KVM: Clear async page fault hash after switching to real mode
KVM: VMX: Initialize vm86 TSS only once.
...
* 'stable/irq.fairness' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen: events: Remove redundant clear of l2i at end of round-robin loop
xen: events: Make round-robin scan fairer by snapshotting each l2 word once only
xen: events: Clean up round-robin evtchn scan.
xen: events: Make last processed event channel a per-cpu variable.
xen: events: Process event channels notifications in round-robin order.
* 'stable/irq.ween_of_nr_irqs' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen: events: Fix compile error if CONFIG_SMP is not defined.
xen: events: correct locking in xen_irq_from_pirq
xen: events: propagate irq allocation failure instead of panicking
xen: events: do not workaround too-small nr_irqs
xen: events: remove use of nr_irqs as upper bound on number of pirqs
xen: events: dynamically allocate irq info structures
xen: events: maintain a list of Xen interrupts
xen: events: push setup of irq<->{evtchn,ipi,virq,pirq} maps into irq_info init functions
xen: events: turn irq_info constructors into initialiser functions
xen: events: use per-cpu variable for cpu_evtchn_mask
xen: events: refactor GSI pirq bindings functions
xen: events: rename restore_cpu_pirqs -> restore_pirqs
xen: events: remove unused public functions
xen: events: fix xen_map_pirq_gsi error return
xen: events: simplify comment
xen: events: separate two unrelated halves of if condition
Fix up trivial conflicts in drivers/xen/events.c
* 'stable/hvc-console' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/hvc: Disable probe_irq_on/off from poking the hvc-console IRQ line.
* 'stable/gntalloc.v6' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen: gntdev: fix build warning
xen/p2m/m2p/gnttab: do not add failed grant maps to m2p override
xen-gntdev: Add cast to pointer
xen-gntdev: Fix incorrect use of zero handle
xen: change xen/[gntdev/gntalloc] to default m
xen-gntdev: prevent using UNMAP_NOTIFY_CLEAR_BYTE on read-only mappings
xen-gntdev: Avoid double-mapping memory
xen-gntdev: Avoid unmapping ranges twice
xen-gntdev: Use map->vma for checking map validity
xen-gntdev: Fix unmap notify on PV domains
xen-gntdev: Fix memory leak when mmap fails
xen/gntalloc,gntdev: Add unmap notify ioctl
xen-gntalloc: Userspace grant allocation driver
xen-gntdev: Support mapping in HVM domains
xen-gntdev: Add reference counting to maps
xen-gntdev: Use find_vma rather than iterating our vma list manually
xen-gntdev: Change page limit to be global instead of per-open
* 'stable/balloon' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen: (24 commits)
xen-gntdev: Use ballooned pages for grant mappings
xen-balloon: Add interface to retrieve ballooned pages
xen-balloon: Move core balloon functionality out of module
xen/balloon: Remove pr_info's and don't alter retry_count
xen/balloon: Protect against CPU exhaust by event/x process
xen/balloon: Migration from mod_timer() to schedule_delayed_work()
xen/balloon: Removal of driver_pages
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp: (38 commits)
amd64_edac: Fix decode_syndrome types
amd64_edac: Fix DCT argument type
amd64_edac: Fix ranges signedness
amd64_edac: Drop local variable
amd64_edac: Fix PCI config addressing types
amd64_edac: Fix DRAM base macros
amd64_edac: Fix node id signedness
amd64_edac: Drop redundant declarations
amd64_edac: Enable driver on F15h
amd64_edac: Adjust ECC symbol size to F15h
amd64_edac: Simplify scrubrate setting
PCI: Rename CPU PCI id define
amd64_edac: Improve DRAM address mapping
amd64_edac: Sanitize ->read_dram_ctl_register
amd64_edac: Adjust sys_addr to chip select conversion routine to F15h
amd64_edac: Beef up early exit reporting
amd64_edac: Revamp online spare handling
amd64_edac: Fix channel interleave removal
amd64_edac: Correct node interleaving removal
amd64_edac: Add support for interleaved region swapping
...
Fix up trivial conflict in include/linux/pci_ids.h due to
AMD_15H_NB_MISC being renamed as AMD_15H_NB_F3 next to the new
AMD_15H_NB_LINK entry.
Ingo Molnar