Since both tx_ring and first_tx are the head of tx ring, it not
necessary to use two structure members to statically indicate
the head of tx ring. So first_tx is removed.
CC: Srinivas Eeda <srinivas.eeda@oracle.com>
CC: Joe Jin <joe.jin@oracle.com>
CC: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the requested dump level parameter to big-endian at the start of
nfp_net_dump_calculate_size() and nfp_net_dump_populate_buffer(), then
compare and assign it directly where needed in the traversal and prolog
code. This decreases the total number of conversions used.
Signed-off-by: Carl Heymann <carl.heymann@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Delete match field defines that are not supported at this time.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Port matching is selected by default on every rule so remove check for it
and delete 'else' side of the statement. Remove nfp_flower_meta_one as now
it will not feature in the code. Rename nfp_flower_meta_two given that one
has been removed.
'Additional metadata' if statement can never be true so remove it as well.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the matching of mac/mpls as a default selection. These are not
necessarily set by a TC rule (unlike the port). Previously a mac/mpls
field would exist in every match and be masked out if not used. This patch
has no impact on functionality but removes unnessary memory assignment in
the match cmsg.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all variants of the sh_eth hardware have Gigabit
support. Unfortunately, the current driver doesn't tell the PHY about
the limited MAC capabilities. Due to this, if you have a Gigabit
capable PHY, the PHY will advertise its Gigabit capability and
establish a link at 1Gbit/s, even though the MAC doesn't support it.
In order to avoid this, we use the recently introduced
phy_set_max_speed() to tell the PHY to not advertise speed higher than
100 MBit/s.
Tested on a SH7786 platform, with a Gigabit PHY.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most callers of rhashtable_walk_start don't care about a resize event
which is indicated by a return value of -EAGAIN. So calls to
rhashtable_walk_start are wrapped wih code to ignore -EAGAIN. Something
like this is common:
ret = rhashtable_walk_start(rhiter);
if (ret && ret != -EAGAIN)
goto out;
Since zero and -EAGAIN are the only possible return values from the
function this check is pointless. The condition never evaluates to true.
This patch changes rhashtable_walk_start to return void. This simplifies
code for the callers that ignore -EAGAIN. For the few cases where the
caller cares about the resize event, particularly where the table can be
walked in mulitple parts for netlink or seq file dump, the function
rhashtable_walk_start_check has been added that returns -EAGAIN on a
resize event.
Signed-off-by: Tom Herbert <tom@quantonium.net>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macro used to access or set an RSS table entry was using an offset
of 8, while it should use an offset of 0. This lead to wrongly configure
the RSS table, not accessing the right entries.
Fixes: 1d7d15d79f ("net: mvpp2: initialize the RSS tables")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use meminfo to identify the egress and ingress context regions and
fetch all valid contexts from those regions. Also flush all contexts
before attempting collection to prevent stale information.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use meminfo to identify TX and RX payload regions and skip them in
collection of EDC, MC, and HMA.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use meminfo to get base address and size of MC memory. Also use same
meminfo for EDC memory dumps.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Collect memory layout of various on-chip memory regions. Move code
for collecting on-chip memory information to cudbg_lib.c and update
cxgb4_debugfs.c to use the common function. Also include
cudbg_entity.h before cudbg_lib.h to avoid adding cudbg entity
structure forward declarations in cudbg_lib.h.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is nothing that says that number of TX queues == number of RX
queues. E.g. the ARTPEC-6 SoC has 2 TX queues and 1 RX queue.
This code is obviously wrong:
for (chan = 0; chan < tx_channel_count; chan++) {
struct stmmac_rx_queue *rx_q = &priv->rx_queue[chan];
priv->rx_queue has size MTL_MAX_RX_QUEUES, so this will send an
uninitialized napi_struct to __napi_schedule(), causing us to
crash in net_rx_action(), because napi_struct->poll is zero.
[12846.759880] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[12846.768014] pgd = (ptrval)
[12846.770742] [00000000] *pgd=39ec7831, *pte=00000000, *ppte=00000000
[12846.777023] Internal error: Oops: 80000007 [#1] PREEMPT SMP ARM
[12846.782942] Modules linked in:
[12846.785998] CPU: 0 PID: 161 Comm: dropbear Not tainted 4.15.0-rc2-00285-gf5fb5f2f39a7 #36
[12846.794177] Hardware name: Axis ARTPEC-6 Platform
[12846.798879] task: (ptrval) task.stack: (ptrval)
[12846.803407] PC is at 0x0
[12846.805942] LR is at net_rx_action+0x274/0x43c
[12846.810383] pc : [<00000000>] lr : [<80bff064>] psr: 200e0113
[12846.816648] sp : b90d9ae8 ip : b90d9ae8 fp : b90d9b44
[12846.821871] r10: 00000008 r9 : 0013250e r8 : 00000100
[12846.827094] r7 : 0000012c r6 : 00000000 r5 : 00000001 r4 : bac84900
[12846.833619] r3 : 00000000 r2 : b90d9b08 r1 : 00000000 r0 : bac84900
Since each DMA channel can be used for rx and tx simultaneously,
the current code should probably be rewritten so that napi_struct is
embedded in a new struct stmmac_channel.
That way, stmmac_poll() can call stmmac_tx_clean() on just the tx queue
where we got the IRQ, instead of looping through all tx queues.
This is also how the xgbe driver does it (another driver for this IP).
Fixes: c22a3f48ef ("net: stmmac: adding multiple napi mechanism")
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After applying 2270bc5da3 ("bnxt_en: Fix netpoll handling") and
903649e718 ("bnxt_en: Improve -ENOMEM logic in NAPI poll loop."),
we still see the following WARN fire:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1875170 at net/core/netpoll.c:165 netpoll_poll_dev+0x15a/0x160
bnxt_poll+0x0/0xd0 exceeded budget in poll
<snip>
Call Trace:
[<ffffffff814be5cd>] dump_stack+0x4d/0x70
[<ffffffff8107e013>] __warn+0xd3/0xf0
[<ffffffff8107e07f>] warn_slowpath_fmt+0x4f/0x60
[<ffffffff8179519a>] netpoll_poll_dev+0x15a/0x160
[<ffffffff81795f38>] netpoll_send_skb_on_dev+0x168/0x250
[<ffffffff817962fc>] netpoll_send_udp+0x2dc/0x440
[<ffffffff815fa9be>] write_ext_msg+0x20e/0x250
[<ffffffff810c8125>] call_console_drivers.constprop.23+0xa5/0x110
[<ffffffff810c9549>] console_unlock+0x339/0x5b0
[<ffffffff810c9a88>] vprintk_emit+0x2c8/0x450
[<ffffffff810c9d5f>] vprintk_default+0x1f/0x30
[<ffffffff81173df5>] printk+0x48/0x50
[<ffffffffa0197713>] edac_raw_mc_handle_error+0x563/0x5c0 [edac_core]
[<ffffffffa0197b9b>] edac_mc_handle_error+0x42b/0x6e0 [edac_core]
[<ffffffffa01c3a60>] sbridge_mce_output_error+0x410/0x10d0 [sb_edac]
[<ffffffffa01c47cc>] sbridge_check_error+0xac/0x130 [sb_edac]
[<ffffffffa0197f3c>] edac_mc_workq_function+0x3c/0x90 [edac_core]
[<ffffffff81095f8b>] process_one_work+0x19b/0x480
[<ffffffff810967ca>] worker_thread+0x6a/0x520
[<ffffffff8109c7c4>] kthread+0xe4/0x100
[<ffffffff81884c52>] ret_from_fork+0x22/0x40
This happens because we increment rx_pkts on -ENOMEM and -EIO, resulting
in rx_pkts > 0. Fix this by only bumping rx_pkts if we were actually
given a non-zero budget.
Signed-off-by: Calvin Owens <calvinowens@fb.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bytes_compl and pkts_compl pointers passed to efx_dequeue_buffers
cannot be NULL. Add a paranoid warning to check this condition and fix
the one case where they were NULL.
efx_enqueue_unwind() is called very rarely, during error handling.
Without this fix it would fail with a NULL pointer dereference in
efx_dequeue_buffer, with efx_enqueue_skb in the call stack.
Fixes: e9117e5099 ("sfc: Firmware-Assisted TSO version 2")
Reported-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Tested-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This controller does not support EEE, but it may connect to a PHY
which supports EEE and advertises EEE by default, while its link
partner also advertises EEE. If this happens, the PHY enters low
power mode when the traffic rate is low and causes packet loss.
This patch disables EEE advertisement by default for any PHY that
gianfar connects to, to prevent the above unwanted outcome.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Tested-by: Yangbo Lu <Yangbo.lu@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
If clk_set_rate() fails, we should disable clk before return.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Branislav Radocaj <branislav@radocaj.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
add appropriate calls to clk_disable_unprepare() by jumping to out_mdio
in case orion_mdio_probe() returns -EPROBE_DEFER.
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 3d604da1e9 ("net: mvmdio: get and enable optional clock")
Signed-off-by: Tobias Jordan <Tobias.Jordan@elektrobit.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some dual port NICs, the 2 ports have to be configured with compatible
link speeds. Under some conditions, a port's configured speed may no
longer be supported. The firmware will send a message to the driver
when this happens.
Improve this logic that prints out the warning by only printing it if
we can determine the link speed that is no longer supported. If the
speed is unknown or it is in autoneg mode, skip the warning message.
Reported-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Tested-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, whenever the NETIF_F_HW_TC feature changes, we silently
always allow it, but we actually do not disable the flows in HW
on disable. That breaks user's expectations. So just forbid
the feature disable in case there are any filters offloaded.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcfm_dev always points to the correct netdev and we already
hold a refcnt, so no need to use tcfm_ifindex to lookup again.
If we would support moving target netdev across netns, using
pointer would be better than ifindex.
This also fixes dumping obsolete ifindex, now after the
target device is gone we just dump 0 as ifindex.
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Offload IP header checksum to NIC.
This fixes a previous patch which disabled checksum offloading
for both IPv4 and IPv6 packets. So L3 checksum offload was
getting disabled for IPv4 pkts. And HW is dropping these pkts
for some reason.
Without this patch, IPv4 TSO appears to be broken:
WIthout this patch I get ~16kbyte/s, with patch close to 2mbyte/s
when copying files via scp from test box to my home workstation.
Looking at tcpdump on sender it looks like hardware drops IPv4 TSO skbs.
This patch restores performance for me, ipv6 looks good too.
Fixes: fa6d7cb5d7 ("net: thunderx: Fix TCP/UDP checksum offload for IPv6 pkts")
Cc: Sunil Goutham <sgoutham@cavium.com>
Cc: Aleksey Makarov <aleksey.makarov@auriga.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Smatch warns that:
drivers/net/ethernet/broadcom/bnxt/bnxt_tc.c:160 bnxt_tc_parse_actions()
error: uninitialized symbol 'rc'.
"rc" is either uninitialized or set to zero here so we can just remove
the check.
Fixes: 8c95f773b4 ("bnxt_en: add support for Flower based vxlan encap/decap offload")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the rx_fs_lock is no longer held across allocation, it's safe
to use GFP_KERNEL for allocating new entries.
This reverts commit 81da3bf6e3 ("net: macb: change GFP_KERNEL to
GFP_ATOMIC").
Cc: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Julia Cartwright <julia@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit ae8223de3d ("net: macb: Added support for RX filtering")
introduces a lock, rx_fs_lock which is intended to protect the list of
rx_flow items and synchronize access to the hardware rx filtering
registers.
However, the region protected by this lock is overscoped, unnecessarily
including things like slab allocation. Reduce this lock scope to only
include operations which must be performed atomically: list traversal,
addition, and removal, and hitting the macb filtering registers.
This fixes the use of kmalloc w/ GFP_KERNEL in atomic context.
Fixes: ae8223de3d ("net: macb: Added support for RX filtering")
Cc: Rafal Ozieblo <rafalo@cadence.com>
Cc: Julia Lawall <julia.lawall@lip6.fr>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Julia Cartwright <julia@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The list_for_each_entry() macro already handles the case where the list
is empty (by not executing the loop body). It's not necessary to handle
this case specially, so stop doing so.
Cc: Rafal Ozieblo <rafalo@cadence.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Julia Cartwright <julia@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the rmnet device creation fails in the newlink either while
registering with the physical device or after subsequent
operations, the rmnet endpoint information is never freed.
Fixes: ceed73a2cf ("drivers: net: ethernet: qualcomm: rmnet: Initial implementation")
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a skb in transmit path does not have sufficient headroom to add
the map header, the skb is not sent out and is never freed.
Fixes: ceed73a2cf ("drivers: net: ethernet: qualcomm: rmnet: Initial implementation")
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
- The spec defines CSR address ranges for indirect ME CSRs. For Each TLV
chunk in the spec, dump a chunk that includes the spec and the data
over the defined address range.
- Each indirect CSR has 8 contexts. To read one context, first write the
context to a specific derived address, read it back, and then read the
register value.
- For each address, read and dump all 8 contexts in this manner.
Signed-off-by: Carl Heymann <carl.heymann@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- The spec defines CSR address ranges for these types.
- Dump each TLV chunk in the spec as a chunk that includes the spec and
the data over the defined address range.
Signed-off-by: Carl Heymann <carl.heymann@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dump FW name as TLV, based on dump specification.
Signed-off-by: Carl Heymann <carl.heymann@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Add spec TLV for hwinfo field, containing key string as data.
- Add dump TLV for hwinfo field, with data being key and value as packed
zero-terminated strings.
- If specified hwinfo field is not found, dump the spec TLV as -ENOENT
error.
Signed-off-by: Carl Heymann <carl.heymann@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Dump hwinfo as separate TLV chunk, in a packed format containing
zero-separated key and value strings.
- This provides additional debug context, if requested by the dumpspec.
Signed-off-by: Carl Heymann <carl.heymann@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Support rtsym TLVs.
- If specified rtsym is not found, dump the spec TLV as -ENOENT error.
Signed-off-by: Carl Heymann <carl.heymann@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Perform dumpspec traversals for calculating size and populating the
dump.
- Initially, wrap all spec TLVs in dump error TLVs (changed by later
patches in the series).
Signed-off-by: Carl Heymann <carl.heymann@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Use a TLV structure, with the typed chunks aligned to 8-byte sizes.
- Dump numeric fields as big-endian.
- Prolog contains the dump level.
Signed-off-by: Carl Heymann <carl.heymann@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Load the TLV-based binary specification of what needs to be included in
a dump, from the "_abi_dump_spec" rtsymbol. If the symbol is not defined,
then dumps for levels >= 1 are not supported.
Signed-off-by: Carl Heymann <carl.heymann@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Skeleton code to perform a binary debug dump via ethtoolops
"set_dump", "get_dump_flags" and "get_dump_data", i.e. the ethtool
-W/w mechanism.
- Skeleton functions for debugdump operations provided.
- An integer "dump level" can be specified, this is stored between
ethtool invocations. Dump level 0 is still the "arm.diag" resource for
backward compatibility. Other dump levels each define a set of state
information to include in the dump, driven by a spec from FW.
Signed-off-by: Carl Heymann <carl.heymann@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using NULL as argument for the DMA mapping API is bogus, as the DMA
mapping API may use information from the "struct device" to perform
the DMA mapping operation. Therefore, pass the appropriate "struct
device".
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two types of "struct device": the one representing the
physical device on its physical bus (platform, SPI, PCI, etc.), and
the one representing the logical device in its device class (net,
etc.).
The DMA mapping API expects to receive as argument a "struct device"
representing the physical device, as the "struct device" contains
information about the bus that the DMA API needs.
However, the sh_eth driver mistakenly uses the "struct device"
representing the logical device (embedded in "struct net_device")
rather than the "struct device" representing the physical device on
its bus.
This commit fixes that by adjusting all calls to the DMA mapping API.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the phylib now being aware of the "reset-gpios" PHY node property,
there should be no need to frob the PHY reset in this driver anymore...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to LS1021A RM, the value of PAL can be set so that the start of the
IP header in the receive data buffer is aligned to a 32-bit boundary. Normally,
setting PAL = 2 provides minimal padding to ensure such alignment of the IP
header.
However every incoming packet's 8-byte time stamp will be inserted into the
packet data buffer as padding alignment bytes when hardware time stamping is
enabled.
So we set the padding 8+2 here to avoid the flooded alignment faults:
root@128:~# cat /proc/cpu/alignment
User: 0
System: 17539 (inet_gro_receive+0x114/0x2c0)
Skipped: 0
Half: 0
Word: 0
DWord: 0
Multi: 17539
User faults: 2 (fixup)
Also shown when exception report enablement
CPU: 0 PID: 161 Comm: irq/66-eth1_g0_ Not tainted 4.1.21-rt13-WR8.0.0.0_preempt-rt #16
Hardware name: Freescale LS1021A
[<8001b420>] (unwind_backtrace) from [<8001476c>] (show_stack+0x20/0x24)
[<8001476c>] (show_stack) from [<807cfb48>] (dump_stack+0x94/0xac)
[<807cfb48>] (dump_stack) from [<80025d70>] (do_alignment+0x720/0x958)
[<80025d70>] (do_alignment) from [<80009224>] (do_DataAbort+0x40/0xbc)
[<80009224>] (do_DataAbort) from [<80015398>] (__dabt_svc+0x38/0x60)
Exception stack(0x86ad1cc0 to 0x86ad1d08)
1cc0: f9b3e080 86b3d072 2d78d287 00000000 866816c0 86b3d05e 86e785d0 00000000
1ce0: 00000011 0000000e 80840ab0 86ad1d3c 86ad1d08 86ad1d08 806d7fc0 806d806c
1d00: 40070013 ffffffff
[<80015398>] (__dabt_svc) from [<806d806c>] (inet_gro_receive+0x114/0x2c0)
[<806d806c>] (inet_gro_receive) from [<80660eec>] (dev_gro_receive+0x21c/0x3c0)
[<80660eec>] (dev_gro_receive) from [<8066133c>] (napi_gro_receive+0x44/0x17c)
[<8066133c>] (napi_gro_receive) from [<804f0538>] (gfar_clean_rx_ring+0x39c/0x7d4)
[<804f0538>] (gfar_clean_rx_ring) from [<804f0bf4>] (gfar_poll_rx_sq+0x58/0xe0)
[<804f0bf4>] (gfar_poll_rx_sq) from [<80660b10>] (net_rx_action+0x27c/0x43c)
[<80660b10>] (net_rx_action) from [<80033638>] (do_current_softirqs+0x1e0/0x3dc)
[<80033638>] (do_current_softirqs) from [<800338c4>] (__local_bh_enable+0x90/0xa8)
[<800338c4>] (__local_bh_enable) from [<8008025c>] (irq_forced_thread_fn+0x70/0x84)
[<8008025c>] (irq_forced_thread_fn) from [<800805e8>] (irq_thread+0x16c/0x244)
[<800805e8>] (irq_thread) from [<8004e490>] (kthread+0xe8/0x104)
[<8004e490>] (kthread) from [<8000fda8>] (ret_from_fork+0x14/0x2c)
Signed-off-by: Zumeng Chen <zumeng.chen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In exisiting code, the way to detect if driver/client reset should
be executed or if hardware should be be soft resetted was overly
complex.
Existing code use to read the interrupt status register from task
context to figure out if the interrupt source event was reset and
then use clear the interrupt source for reset while waiting for the
hardware to finish the reset. This behaviour again was confusing
and overly complex in terms of the flow.
This patch simplifies the handling of the requested reset and the
pending reset(i.e. reset which have already been asserted by the
software and hardware has acknowledged back to driver that it is
processing the hardware reset through interrupt)
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Existing common service task was being used to service the reset
requests. This patch tries to make the handling of reset cleaner
by separating task to handle the reset requests. This might in
turn help in adapting similar handling approach for other
interrupt events like mailbox, sharing vector 0 interrupt.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reset interrupt event shares common miscellaneous interrupt
Vector 0. In the existing reset interrupt handling we disable
the Vector 0 interrupt in misc interrupt handler and re-enable
them later in context to common service task.
This also means other event sources like mailbox would also be
deferred or if the interrupt event was due to mailbox(which shall
be supported for VF soon), it could delay the reset handling.
This patch reorganizes the reset interrupt handling logic and
makes it more fair to other events.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously we swapped the tx_packets, tx_bytes and tx_dropped counters
with rx_packets, rx_bytes and rx_dropped counters, respectively. This
behaviour is correct and expected for VF representors but it should not
be swapped for physical port mac representors.
Fixes: eadfa4c3be ("nfp: add stats and xmit helpers for representors")
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function gem_add_flow_filter called on line 2958 inside lock on line 2949
but uses GFP_KERNEL
Generated by: scripts/coccinelle/locks/call_kern.cocci
Fixes: ae8223de3d ("net: macb: Added support for RX filtering")
CC: Rafal Ozieblo <rafalo@cadence.com>
Signed-off-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Small overlapping change conflict ('net' changed a line,
'net-next' added a line right afterwards) in flexcan.c
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2017-12-03
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Addition of a software model for BPF offloads in order to ease
testing code changes in that area and make semantics more clear.
This is implemented in a new driver called netdevsim, which can
later also be extended for other offloads. SR-IOV support is added
as well to netdevsim. BPF kernel selftests for offloading are
added so we can track basic functionality as well as exercising
all corner cases around BPF offloading, from Jakub.
2) Today drivers have to drop the reference on BPF progs they hold
due to XDP on device teardown themselves. Change this in order
to make XDP handling inside the drivers less error prone, and
move disabling XDP to the core instead, also from Jakub.
3) Misc set of BPF verifier improvements and cleanups as preparatory
work for upcoming BPF-to-BPF calls. Among others, this set also
improves liveness marking such that pruning can be slightly more
effective. Register and stack liveness information is now included
in the verifier log as well, from Alexei.
4) nfp JIT improvements in order to identify load/store sequences in
the BPF prog e.g. coming from memcpy lowering and optimizing them
through the NPU's command push pull (CPP) instruction, from Jiong.
5) Cleanups to test_cgrp2_attach2.c BPF sample code in oder to remove
bpf_prog_attach() magic values and replacing them with actual proper
attach flag instead, from David.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ethtool ops to advertise sw timestamping.
Call skb_tx_timestamp() just before ringing the wq doorbell.
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove one extraneous level of indentation on assignment statement.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mss variable tracks the last max segment size sent to the TSO
engine. We do not update the hardware as long as we receive skb:s with
the same value in gso_size.
During a network device down/up cycle (mapped to stmmac_release() and
stmmac_open() callbacks) we issue a reset to the hardware and it
forgets the setting for mss. However we did not zero out our mss
variable so the next transmission of a gso packet happens with an
undefined hardware setting.
This triggers a hang in the TSO engine and eventuelly the netdev
watchdog will bark.
Fixes: f748be531d ("stmmac: support new GMAC4")
Signed-off-by: Lars Persson <larper@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
short_input variable is assigned to another data pointer which is
referred out of its scope. Fix it by moving short_input definition
to the beginning of bnxt_hwrm_do_send_msg() function.
No failure has been reported so far due to this issue.
Fixes: e605db801b ("bnxt_en: Support for Short Firmware Message")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For flows that involve a vxlan encap action, the vxlan sock
interface may be specified as the outgoing interface. The driver
must resolve the outgoing PF interface used by this socket and
use the dst_fid of the PF in the hwrm_cfa_encap_record_alloc cmd.
Similarily for flows that have a vxlan decap action, the
fid of the incoming PF interface must be used as the src_fid in
the hwrm_cfa_decap_filter_alloc cmd.
Fixes: 8c95f773b4 ("bnxt_en: add support for Flower based vxlan encap/decap offload")
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While creating a decap filter the tunnel smac need not (and must not) be
specified as we cannot ascertain the neighbor in the recv path. 'ttl'
match is also not needed for the decap filter and must be wild-carded.
Fixes: f484f6782e ("bnxt_en: add hwrm FW cmds for cfa_encap_record and decap_filter")
Signed-off-by: Sunil Challa <sunilkumar.challa@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current 'bnxt_shutdown' implementation only invokes
'bnxt_ulp_shutdown' to shut down RoCE in the case when the system is in
the path of power off (SYSTEM_POWER_OFF). While this may work in most
cases, it does not work in the smart NIC case, when Linux 'reboot'
command is initiated from the Linux that runs on the ARM cores of the
NIC card. In this particular case, Linux 'reboot' results in a system
'L3' level reset where the entire ARM and associated subsystems are
being reset, but at the same time, Nitro core is being kept in sane state
(to allow external PCIe connected servers to continue to work). Without
properly shutting down RoCE and freeing all associated resources, it
results in the ARM core to hang immediately after the 'reboot'
By always invoking 'bnxt_ulp_shutdown' in 'bnxt_shutdown', it fixes the
above issue
Fixes: 0efd2fc65c ("bnxt_en: Add a callback to inform RDMA driver during PCI shutdown.")
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since day one of XDP drivers had to remember to free the program
on the remove path. This leads to code duplication and is error
prone. Make the stack query the installed programs on unregister
and if something is installed, remove the program. Freeing of
program attached to XDP generic is moved from free_netdev() as well.
Because the remove will now be called before notifiers are
invoked, BPF offload state of the program will not get destroyed
before uninstall.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Some drivers enforce that flags on program replacement and
removal must match the flags passed on install. This leaves
the possibility open to enable simultaneous loading
of XDP programs both to HW and DRV.
Allow such drivers to report the flags back to the stack.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
ALE ports number includes the Host port and ext Ports, and
ALE ports numbering starts from 0, so correct corresponding port
checks in cpsw_ale_control_set/get().
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use cpsw_ale_create in cpsw_ale_create(). This also makes
cpsw_ale_destroy() function nop, so remove it.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move static initialization from cpsw_ale_start() to cpsw_ale_create() as it
does not make much sence to perform static initializtion in
cpsw_ale_start() which is called everytime netif[s] is opened.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ale->params.ale_ports parameter can be used to deriver values for all
ale entry mask bits: port_mask_bits, port_mask_bits, port_num_bits.
Hence, calculate above values and drop all hardcoded values. For
port_num_bits calcualtion use order_base_2() API.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ALE is enabled from cpsw_ale_start() now, but disabled only from
cpsw_ale_destroy() which introduces inconsitance as cpsw_ale_start() is
called when netif[s] is opened, but cpsw_ale_destroy() is called when
driver is removed. Hence, move ALE disabling in cpsw_ale_stop().
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch to use writel_relaxed/readl_relaxed() IO API instead of raw version
as it is recommended.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TI OMAP/Sitara SoCs have fixed number of ALE ports 3, which includes Host
port also.
Hence, use fixed value instead of value calcualted from DT, which can be
set by user and might not reflect actual HW configuration.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move mac_hi/lo defines in common header cpsw.h and re-use
them for netcp_ethss.c.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CPSW platform data struct cpsw_platform_data and struct cpsw_slave_data are
used only incide cpsw.c module, so move these definitions there.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch to use writel_relaxed/readl_relaxed() IO API instead of raw version
as it is recommended.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop unused variable "poll" from cpsw_update_channels_res().
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ETH_RESET_AP support handling to reset the internal
Application Processor(s) of the SmartNIC card.
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add the optimization frontend, but adding a new eBPF IR scan
pass "nfp_bpf_opt_ldst_gather".
The pass will traverse the IR to recognize the load/store pairs sequences
that come from lowering of memory copy builtins.
The gathered memory copy information will be kept in the meta info
structure of the first load instruction in the sequence and will be
consumed by the optimization backend added in the previous patches.
NOTE: a sequence with cross memory access doesn't qualify this
optimization, i.e. if one load in the sequence will load from place that
has been written by previous store. This is because when we turn the
sequence into single CPP operation, we are reading all contents at once
into NFP transfer registers, then write them out as a whole. This is not
identical with what the original load/store sequence is doing.
Detecting cross memory access for two random pointers will be difficult,
fortunately under XDP/eBPF's restrictied runtime environment, the copy
normally happen among map, packet data and stack, they do not overlap with
each other.
And for cases supported by NFP, cross memory access will only happen on
PTR_TO_PACKET. Fortunately for this, there is ID information that we could
do accurate memory alias check.
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
When the gathered copy length is bigger than 32-bytes and within 128-bytes
(the maximum length a single CPP Pull/Push request can finish), the
strategy of read/write are changeed into:
* Read.
- use direct reference mode when length is within 32-bytes.
- use indirect mode when length is bigger than 32-bytes.
* Write.
- length <= 8-bytes
use write8 (direct_ref).
- length <= 32-byte and 4-bytes aligned
use write32 (direct_ref).
- length <= 32-bytes but not 4-bytes aligned
use write8 (indirect_ref).
- length > 32-bytes and 4-bytes aligned
use write32 (indirect_ref).
- length > 32-bytes and not 4-bytes aligned and <= 40-bytes
use write32 (direct_ref) to finish the first 32-bytes.
use write8 (direct_ref) to finish all remaining hanging part.
- length > 32-bytes and not 4-bytes aligned
use write32 (indirect_ref) to finish those 4-byte aligned parts.
use write8 (direct_ref) to finish all remaining hanging part.
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
For NFP, we want to re-group a sequence of load/store pairs lowered from
memcpy/memmove into single memory bulk operation which then could be
accelerated using NFP CPP bus.
This patch extends the existing load/store auxiliary information by adding
two new fields:
struct bpf_insn *paired_st;
s16 ldst_gather_len;
Both fields are supposed to be carried by the the load instruction at the
head of the sequence. "paired_st" is the corresponding store instruction at
the head and "ldst_gather_len" is the gathered length.
If "ldst_gather_len" is negative, then the sequence is doing memory
load/store in descending order, otherwise it is in ascending order. We need
this information to detect overlapped memory access.
This patch then optimize memory bulk copy when the copy length is within
32-bytes.
The strategy of read/write used is:
* Read.
Use read32 (direct_ref), always.
* Write.
- length <= 8-bytes
write8 (direct_ref).
- length <= 32-bytes and is 4-byte aligned
write32 (direct_ref).
- length <= 32-bytes but is not 4-byte aligned
write8 (indirect_ref).
NOTE: the optimization should not change program semantics. The destination
register of the last load instruction should contain the same value before
and after this optimization.
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
It is usual that we need to check if one BPF insn is for loading/storeing
data from/to memory.
Therefore, it makes sense to factor out related code to become common
helper functions.
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Add support for emitting commands with field overwrites.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
When immed is used with No-Dest, the emitter should use reg.dst instead of
reg.areg for the destination, using the latter will actually encode
register zero.
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The NFP normally requires the source operands to be difference addressing
modes, but we should rule out the very special NN_REG_NONE type.
There are instruction that ignores both A/B operands, for example:
local_csr_rd
For these instructions, we might pass the same operand type, NN_REG_NONE,
for both A/B operands.
NOTE: in current NFP ISA, it is only possible for instructions with
unrestricted operands to take none operands, but in case there is new and
similar instructoin in restricted form, they would follow similar rules,
so swreg_to_restricted is updated as well.
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
If any of the shift insns in the ld/shift sequence is jump destination,
don't do combination.
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
If the mask insn in the ld/mask pair is jump destination, then don't do
combination.
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
NFP eBPF offload JIT engine is doing some instruction combine based
optimizations which however must not be safe if the combined sequences
are across basic block boarders.
Currently, there are post checks during fixing jump destinations. If the
jump destination is found to be eBPF insn that has been combined into
another one, then JIT engine will raise error and abort.
This is not optimal. The JIT engine ought to disable the optimization on
such cross-bb-border sequences instead of abort.
As there is no control flow information in eBPF infrastructure that we
can't do basic block based optimizations, this patch extends the existing
jump destination record pass to also flag the jump destination, then in
instruction combine passes we could skip the optimizations if insns in the
sequence are jump targets.
Suggested-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
eBPF insns are internally organized as dual-list inside NFP offload JIT.
Random access to an insn needs to be done by either forward or backward
traversal along the list.
One place we need to do such traversal is at nfp_fixup_branches where one
traversal is needed for each jump insn to find the destination. Such
traversals could be avoided if jump destinations are collected through a
single travesal in a pre-scan pass, and such information could also be
useful in other places where jump destination info are needed.
This patch adds such jump destination collection in nfp_prog_prepare.
Suggested-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This patch adds support for backward jump on NFP.
- restrictions on backward jump in various functions have been removed.
- nfp_fixup_branches now supports backward jump.
There is one thing to note, currently an input eBPF JMP insn may generate
several NFP insns, for example,
NFP imm move insn A \
NFP compare insn B --> 3 NFP insn jited from eBPF JMP insn M
NFP branch insn C /
---
NFP insn X --> 1 NFP insn jited from eBPF insn N
---
...
therefore, we are doing sanity check to make sure the last jited insn from
an eBPF JMP is a NFP branch instruction.
Once backward jump is allowed, it is possible an eBPF JMP insn is at the
end of the program. This is however causing trouble for the sanity check.
Because the sanity check requires the end index of the NFP insns jited from
one eBPF insn while only the start index is recorded before this patch that
we can only get the end index by:
start_index_of_the_next_eBPF_insn - 1
or for the above example:
start_index_of_eBPF_insn_N (which is the index of NFP insn X) - 1
nfp_fixup_branches was using nfp_for_each_insn_walk2 to expose *next* insn
to each iteration during the traversal so the last index could be
calculated from which. Now, it needs some extra code to handle the last
insn. Meanwhile, the use of walk2 is actually unnecessary, we could simply
use generic single instruction walk to do this, the next insn could be
easily calculated using list_next_entry.
So, this patch migrates the jump fixup traversal method to
*list_for_each_entry*, this simplifies the code logic a little bit.
The other thing to note is a new state variable "last_bpf_off" is
introduced to track the index of the last jited NFP insn. This is necessary
because NFP is generating special purposes epilogue sequences, so the index
of the last jited NFP insn is *not* always nfp_prog->prog_len - 1.
Suggested-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Since commit 3a025e1d1c ("Add optional check for bad kernel-doc
comments") when built with W=1 build will complain about kdoc errors.
Fix the kdoc issues we have. kdoc is still confused by defines in
nfp_net_ctrl.h but those are not really errors.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This patch allows filtering received packets to different
hardware queues (aka ntuple).
Signed-off-by: Rafal Ozieblo <rafalo@cadence.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To be able for packet reception on different RX queues some
configuration has to be performed. This patch checks how many
hardware queue does GEM support and initializes them.
Signed-off-by: Rafal Ozieblo <rafalo@cadence.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver expect "allwinner,leds-active-low" to be in PHY node, but
the binding doc expect it to be in MAC node.
Since all board DT use it also in MAC node, the driver need to search
allwinner,leds-active-low in MAC node.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In xmit, it is very impossible that TX_ERROR occurs. So using
unlikely optimizes the xmit process.
CC: Srinivas Eeda <srinivas.eeda@oracle.com>
CC: Joe Jin <joe.jin@oracle.com>
CC: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netxen_collect_minidump() evidently just wants to get a monotonic
timestamp. Using jiffies_to_timespec(jiffies, &ts) is not
appropriate here, since it will overflow after 2^32 jiffies,
which may be as short as 49 days of uptime.
ktime_get_seconds() is the correct interface here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to reinvent the wheel, we have bus_find_device_by_name().
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
on T81 there are only 4 cores, hence setting max queue count to 4
would leave nothing for XDP_TX. This patch fixes this by doubling
max queue count in above scenarios.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: cjacob <cjacob@caviumnetworks.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for XDP_REDIRECT. Flush is not
yet supported.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: cjacob <cjacob@caviumnetworks.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reserved and unused fields in the Tx descriptors should be 0. The PPv2
driver doesn't clear them at run-time (for performance reasons) but
these descriptors aren't zeroed when allocated, which can lead to
unpredictable behaviors. This patch fixes this by using
dma_zalloc_coherent instead of dma_alloc_coherent.
Fixes: 3f518509de ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Yan Markman <ymarkman@marvell.com>
[Antoine: commit message]
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) The forcedeth conversion from pci_*() DMA interfaces to dma_*() ones
missed one spot. From Zhu Yanjun.
2) Missing CRYPTO_SHA256 Kconfig dep in cfg80211, from Johannes Berg.
3) Fix checksum offloading in thunderx driver, from Sunil Goutham.
4) Add SPDX to vm_sockets_diag.h, from Stephen Hemminger.
5) Fix use after free of packet headers in TIPC, from Jon Maloy.
6) "sizeof(ptr)" vs "sizeof(*ptr)" bug in i40e, from Gustavo A R Silva.
7) Tunneling fixes in mlxsw driver, from Petr Machata.
8) Fix crash in fanout_demux_rollover() of AF_PACKET, from Mike
Maloney.
9) Fix race in AF_PACKET bind() vs. NETDEV_UP notifier, from Eric
Dumazet.
10) Fix regression in sch_sfq.c due to one of the timer_setup()
conversions. From Paolo Abeni.
11) SCTP does list_for_each_entry() using wrong struct member, fix from
Xin Long.
12) Don't use big endian netlink attribute read for
IFLA_BOND_AD_ACTOR_SYSTEM, it is in cpu endianness. Also from Xin
Long.
13) Fix mis-initialization of q->link.clock in CBQ scheduler, preventing
adding filters there. From Jiri Pirko.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (67 commits)
ethernet: dwmac-stm32: Fix copyright
net: via: via-rhine: use %p to format void * address instead of %x
net: ethernet: xilinx: Mark XILINX_LL_TEMAC broken on 64-bit
myri10ge: Update MAINTAINERS
net: sched: cbq: create block for q->link.block
atm: suni: remove extraneous space to fix indentation
atm: lanai: use %p to format kernel addresses instead of %x
VSOCK: Don't set sk_state to TCP_CLOSE before testing it
atm: fore200e: use %pK to format kernel addresses instead of %x
ambassador: fix incorrect indentation of assignment statement
vxlan: use __be32 type for the param vni in __vxlan_fdb_delete
bonding: use nla_get_u64 to extract the value for IFLA_BOND_AD_ACTOR_SYSTEM
sctp: use right member as the param of list_for_each_entry
sch_sfq: fix null pointer dereference at timer expiration
cls_bpf: don't decrement net's refcount when offload fails
net/packet: fix a race in packet_bind() and packet_notifier()
packet: fix crash in fanout_demux_rollover()
sctp: remove extern from stream sched
sctp: force the params with right types for sctp csum apis
sctp: force SCTP_ERROR_INV_STRM with __u32 when calling sctp_chunk_fail
...
Don't use %x and casting to print out an address, instead use %p
and remove the casting. Cleans up smatch warnings:
drivers/net/ethernet/via/via-rhine.c:998 rhine_init_one_common()
warn: argument 4 to %lx specifier is cast from pointer
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On 64-bit (e.g. powerpc64/allmodconfig):
drivers/net/ethernet/xilinx/ll_temac_main.c: In function 'temac_start_xmit_done':
drivers/net/ethernet/xilinx/ll_temac_main.c:633:22: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
dev_kfree_skb_irq((struct sk_buff *)cur_p->app4);
^
cdmac_bd.app4 is u32, so it is too small to hold a kernel pointer.
Note that several other fields in struct cdmac_bd are also too small to
hold physical addresses on 64-bit platforms.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Error code returned by 'bnxt_read_sfp_module_eeprom_info()' is handled a
few lines above when reading the A0 portion of the EEPROM.
The same should be done when reading the A2 portion of the EEPROM.
In order to correctly propagate an error, update 'rc' in this 2nd call as
well, otherwise 0 (success) is returned.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the Tx ring size checks when using ethtool, by adding
an extra check in the PPv2 check_ringparam_valid helper. The Tx ring
size cannot be set to a value smaller than the minimum number of
descriptors needed for TSO.
Fixes: 1d17db08c0 ("net: mvpp2: limit TSO segments and use stop/wake thresholds")
Suggested-by: Yan Markman <ymarkman@marvell.com>
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Short fragmented packets may never be sent by the hardware when padding
is disabled. This patch stop modifying the GMAC padding bits, to leave
them to their reset value (disabled).
Fixes: 3919357fb0 ("net: mvpp2: initialize the GMAC when using a port")
Signed-off-by: Yan Markman <ymarkman@marvell.com>
[Antoine: commit message]
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patches fixes the probe error path by cleaning up probed ports, to
avoid leaving registered net devices when the driver failed to probe.
Fixes: 3f518509de ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an allocation in the txq_init path fails, the allocated buffers
end-up being freed twice: in the txq_init error path, and in txq_deinit.
This lead to issues as txq_deinit would work on already freed memory
regions:
kernel BUG at mm/slub.c:3915!
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
This patch fixes this by removing the txq_init own error path, as the
txq_deinit function is always called on errors. This was introduced by
TSO as way more buffers are allocated.
Fixes: 186cd4d4e4 ("net: mvpp2: software tso support")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function mlxsw_sp_nexthop_rif_update() walks the list of nexthops
associated with a RIF, and updates the corresponding entries in the
switch. It is used in particular when a tunnel underlay netdevice moves
to a different VRF, and all the nexthops are migrated over to a new RIF.
The problem is that each nexthop holds a reference to its RIF, and that
is not updated. So after the old RIF is gone, further activity on these
nexthops (such as downing the underlay netdevice) dereferences a
dangling pointer.
Fix the issue by updating rif of impacted nexthops before calling
mlxsw_sp_nexthop_rif_update().
Fixes: 0c5f1cd5ba ("mlxsw: spectrum_router: Generalize __mlxsw_sp_ipip_entry_update_tunnel()")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some tunnels that are offloadable on their own can nonetheless be
demoted to slow path if their local address is in conflict with that of
another tunnel. When a route is formed for such a tunnel,
mlxsw_sp_nexthop_ipip_init() fails to find the corresponding IPIP entry,
and that triggers a FIB abort.
Resolve the problem by not assuming that a tunnel for which
mlxsw_sp_ipip_ops.can_offload() holds also automatically has an IPIP
entry.
Fixes: af641713e9 ("mlxsw: spectrum_router: Onload conflicting tunnels")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mlxsw driver currently doesn't offload GRE tunnels if they have the
same local address and use the same underlay VRF. When such a situation
arises, the tunnels in conflict are demoted to slow path.
However, the current code only verifies this condition on tunnel
creation and tunnel change, not when a tunnel is moved to a different
VRF. When the tunnel has no bound device, underlay and overlay are the
same. Thus moving a tunnel moves the underlay as well, and that can
cause local address conflict.
So modify mlxsw_sp_netdevice_ipip_ol_vrf_event() to check if there are
any conflicting tunnels, and demote them if yes.
Fixes: af641713e9 ("mlxsw: spectrum_router: Onload conflicting tunnels")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a new local route is added, an IPIP entry is looked up to determine
whether the route should be offloaded as a tunnel decap or as a trap.
That decision should take into account whether the tunnel netdevice in
question is actually IFF_UP, and only install a decap offload if it is.
Fixes: 0063587d35 ("mlxsw: spectrum: Support decap-only IP-in-IP tunnels")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding cloud filters could fail for a number of reasons,
unsupported filter fields for example, which fails during
validation of fields itself. This will not result in admin
command errors and converting the admin queue status to posix
error code using i40e_aq_rc_to_posix would result in incorrect
error values. If the failure was due to AQ error itself,
reporting that correctly is handled in the inner function.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is a follow on to commit b10effb92e ("fix buffer overrun while the
I219 is processing DMA transactions") to address David Laights concerns
about the use of "magic" numbers. So define masks as well as add
additional code comments to give a better understanding of what needs to
be done to avoid a buffer overrun.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Reviewed-by: Alexander H Duyck <alexander.h.duyck@intel.com>
Reviewed-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Reviewed-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
sizeof when applied to a pointer typed expression gives the size of
the pointer.
The proper fix in this particular case is to code sizeof(*vfres)
instead of sizeof(vfres).
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A R Silva <garsilva@embeddedor.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull timer updates from Thomas Gleixner:
- The final conversion of timer wheel timers to timer_setup().
A few manual conversions and a large coccinelle assisted sweep and
the removal of the old initialization mechanisms and the related
code.
- Remove the now unused VSYSCALL update code
- Fix permissions of /proc/timer_list. I still need to get rid of that
file completely
- Rename a misnomed clocksource function and remove a stale declaration
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
m68k/macboing: Fix missed timer callback assignment
treewide: Remove TIMER_FUNC_TYPE and TIMER_DATA_TYPE casts
timer: Remove redundant __setup_timer*() macros
timer: Pass function down to initialization routines
timer: Remove unused data arguments from macros
timer: Switch callback prototype to take struct timer_list * argument
timer: Pass timer_list pointer to callbacks unconditionally
Coccinelle: Remove setup_timer.cocci
timer: Remove setup_*timer() interface
timer: Remove init_timer() interface
treewide: setup_timer() -> timer_setup() (2 field)
treewide: setup_timer() -> timer_setup()
treewide: init_timer() -> setup_timer()
treewide: Switch DEFINE_TIMER callbacks to struct timer_list *
s390: cmm: Convert timers to use timer_setup()
lightnvm: Convert timers to use timer_setup()
drivers/net: cris: Convert timers to use timer_setup()
drm/vc4: Convert timers to use timer_setup()
block/laptop_mode: Convert timers to use timer_setup()
net/atm/mpc: Avoid open-coded assignment of timer callback function
...
Don't offload IP header checksum to NIC.
This fixes a previous patch which enabled checksum offloading
for both IPv4 and IPv6 packets. So L3 checksum offload was
getting enabled for IPv6 pkts. And HW is dropping these pkts
as it assumes the pkt is IPv4 when IP csum offload is set
in the SQ descriptor.
Fixes: 3a9024f52c ("net: thunderx: Enable TSO and checksum offloads for ipv6")
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@auriga.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function pci_unmap_page is obsolete. So it is replaced with
the function dma_unmap_page.
CC: Srinivas Eeda <srinivas.eeda@oracle.com>
CC: Joe Jin <joe.jin@oracle.com>
CC: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Fixes 2017-11-21
This series contains fixes for igb/vf, ixgbe/vf, i40e/vf and fm10k.
Jake fixes a regression issue with older firmware, where we were using
the NVM lock to synchronize NVM reads for all devices and firmware
versions, yet this caused issues with older firmware prior to version
1.5. Fixed this by only grabbing the lock for newer devices and firmware
version 1.5 or newer.
Zijie Pan fixes the calculation of the i40e VF MAC addresses, where it was
possible to increment to the next MAC entry without calling
i40e_add_mac_filter().
Amritha removes the upper limit of 64 queues on a channel VSI since the
upper bound is determined by the VSI's num_queue_pairs.
Filip fixes an issue during FLR resets, where should have been checking
for upcoming core reset and if so, just return with I40E_ERR_NOT_READY.
Alan fixes the notifying clients of l2 parameters by copying the
parameters to the client instance struct and re-organizes the priority
in which the client tasks fire so that if the flag for notifying l2
params is set, it will trigger before the client open task. Also fixed
the promiscuous settings after reset for all the VSI's.
Brian King from IBM fixes an issue seen on Power systems which would
result in skb list corruption and eventual kernel oops. Brian
provides the same fix for nearly all our drivers, to replace the
read_barrier_depends with smp_rmb() to ensure loads are ordered with
respect to the load of tx_buffer->next_to_watch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf 2017-11-23
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Several BPF offloading fixes, from Jakub. Among others:
- Limit offload to cls_bpf and XDP program types only.
- Move device validation into the driver and don't make
any assumptions about the device in the classifier due
to shared blocks semantics.
- Don't pass offloaded XDP program into the driver when
it should be run in native XDP instead. Offloaded ones
are not JITed for the host in such cases.
- Don't destroy device offload state when moved to
another namespace.
- Revert dumping offload info into user space for now,
since ifindex alone is not sufficient. This will be
redone properly for bpf-next tree.
2) Fix test_verifier to avoid using bpf_probe_write_user()
helper in test cases, since it's dumping a warning into
kernel log which may confuse users when only running tests.
Switch to use bpf_trace_printk() instead, from Yonghong.
3) Several fixes for correcting ARG_CONST_SIZE_OR_ZERO semantics
before it becomes uabi, from Gianluca. More specifically:
- Add a type ARG_PTR_TO_MEM_OR_NULL that is used only
by bpf_csum_diff(), where the argument is either a
valid pointer or NULL. The subsequent ARG_CONST_SIZE_OR_ZERO
then enforces a valid pointer in case of non-0 size
or a valid pointer or NULL in case of size 0. Given
that, the semantics for ARG_PTR_TO_MEM in combination
with ARG_CONST_SIZE_OR_ZERO are now such that in case
of size 0, the pointer must always be valid and cannot
be NULL. This fix in semantics allows for bpf_probe_read()
to drop the recently added size == 0 check in the helper
that would become part of uabi otherwise once released.
At the same time we can then fix bpf_probe_read_str() and
bpf_perf_event_output() to use ARG_CONST_SIZE_OR_ZERO
instead of ARG_CONST_SIZE in order to fix recently
reported issues by Arnaldo et al, where LLVM optimizes
two boundary checks into a single one for unknown
variables where the verifier looses track of the variable
bounds and thus rejects valid programs otherwise.
4) A fix for the verifier for the case when it detects
comparison of two constants where the branch is guaranteed
to not be taken at runtime. Verifier will rightfully prune
the exploration of such paths, but we still pass the program
to JITs, where they would complain about using reserved
fields, etc. Track such dead instructions and sanitize
them with mov r0,r0. Rejection is not possible since LLVM
may generate them for valid C code and doesn't do as much
data flow analysis as verifier. For bpf-next we might
implement removal of such dead code and adjust branches
instead. Fix from Alexei.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 6fa1ba6152 partially
implemented the new ethtool API, by replacing get_settings()
with get_link_ksettings(). This breaks ethtool, since the
userspace tool (according to the new API specs) never tries
the legacy set() call, when the new get() call succeeds.
All attempts to chance some setting from userspace result in:
> Cannot set new settings: Operation not supported
Implement the missing set() call.
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Tested-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with i40evf as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with fm10k as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with igb as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with igbvf as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with ixgbevf as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with i40e as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes an issue seen on Power systems with ixgbe which results
in skb list corruption and an eventual kernel oops. The following is what
was observed:
CPU 1 CPU2
============================ ============================
1: ixgbe_xmit_frame_ring ixgbe_clean_tx_irq
2: first->skb = skb eop_desc = tx_buffer->next_to_watch
3: ixgbe_tx_map read_barrier_depends()
4: wmb check adapter written status bit
5: first->next_to_watch = tx_desc napi_consume_skb(tx_buffer->skb ..);
6: writel(i, tx_ring->tail);
The read_barrier_depends is insufficient to ensure that tx_buffer->skb does not
get loaded prior to tx_buffer->next_to_watch, which then results in loading
a stale skb pointer. This patch replaces the read_barrier_depends with
smp_rmb to ensure loads are ordered with respect to the load of
tx_buffer->next_to_watch.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
After a reset we rebuild the VSIs which is going to clobber any
promiscuous settings we had before reset. This makes it so that we
restore the promiscuous settings we had before reset.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The current method for notifying clients of l2 parameters is broken
because we fail to copy the new parameters to the client instance
struct, we need to do the notification before the client 'open' function
pointer gets called, and lastly we should set the l2 parameters when
first adding a client instance.
This patch first introduces the i40evf_client_get_params function to
prevent code duplication in the i40evf_client_add_instance and the
i40evf_notify_client_l2_params functions. We then fix the notify l2
params function to actually copy the parameters to client instance
struct and do the same in the *_add_instance' function. Lastly this
patch reorganizes the priority in which client tasks fire so that if the
flag for notifying l2 params is set, it will trigger before the open
because the client needs these new parameters as part of a client open
task.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch allows detection of upcoming core reset in case NIC gets
stuck while performing FLR reset. The i40e_pf_reset() function returns
I40E_ERR_NOT_READY when global reset was detected.
Signed-off-by: Filip Sadowski <filip.sadowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It is safe to remove the upper limit of 64 queues on a channel
VSI. The upper bound is determined by the VSI's num_queue_pairs
and gets validated when the queue mapping info through mqprio
interface is subject to bound checking in the driver.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
num_mac should be increased only after the call to i40e_add_mac_filter().
Fixes: 5f527ba962 ("i40e: Limit the number of MAC and VLAN addresses that can be added for VFs")
Signed-off-by: Zijie Pan <zijie.pan@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: Tushar Dave <tushar.n.dave@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since commit 96a39aed25 ("i40e: Acquire NVM lock before
reads on all devices") we've used the NVM lock
to synchronize NVM reads even on devices which don't strictly
need the lock.
Doing so can cause a regression on older firmware prior to 1.5,
especially when downgrading the firmware.
Fix this by only grabbing the lock if we're running on an X722
device (which requires the lock as it uses the AdminQ to read
the NVM), or if we're currently running 1.5 or newer firmware.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With all callbacks converted, and the timer callback prototype
switched over, the TIMER_FUNC_TYPE cast is no longer needed,
so remove it. Conversion was done with the following scripts:
perl -pi -e 's|\(TIMER_FUNC_TYPE\)||g' \
$(git grep TIMER_FUNC_TYPE | cut -d: -f1 | sort -u)
perl -pi -e 's|\(TIMER_DATA_TYPE\)||g' \
$(git grep TIMER_DATA_TYPE | cut -d: -f1 | sort -u)
The now unused macros are also dropped from include/linux/timer.h.
Signed-off-by: Kees Cook <keescook@chromium.org>
Commit 0115552eac ("nfp: remove false positive offloads
in flower vxlan") missed adding kdoc for a new parameter
of nfp_flower_add_offload().
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some systems, when we unsplit a port we need to re-create two ports
instead. On other systems, only one needs to be re-created.
Do not try to create a port if during driver initialization it was
assigned a negative module number, which is invalid.
This avoids the following error during unsplit:
[ 941.012478] mlxsw_spectrum 0000:01:00.0: Port 43: Failed to map module
The error is harmless and caused by the fact that a local port is
already mapped to module 0.
Fixes: be94535f95 ("mlxsw: spectrum: Make split flow match firmware requirements")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With TC shared block changes we can't depend on correct netdev
pointer being available in cls_bpf. Move the device validation
to the driver. Core will only make sure that offloaded programs
are always attached in the driver (or in HW by the driver). We
trust that drivers which implement offload callbacks will perform
necessary checks.
Moving the checks to the driver is generally a useful thing,
in practice the check should be against a switchdev instance,
not a netdev, given that most ASICs will probably allow using
the same program on many ports.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Some statements are not enough or too much indented.
Fix it to improve readalbility.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
In rare cases, ena driver would reset and re-start the device,
for example, in case of misbehaving application that causes
transmit timeout
The first step in the reset procedure is to stop the Tx traffic by
calling ena_carrier_off().
After the driver have just started the device reset procedure, device
happens to send an asynchronous notification (via AENQ) to the driver
than there was a link change (to link-up state).
This link change is mapped to a call to netif_carrier_on() which
re-activates the Tx queues, violating the assumption of no tx traffic
until device reset is completed, as the reset task might still be in
the process of queues initialization, leading to an access to
uninitialized memory.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adjust the code to use the same green settings as in the latest
vendor driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Name of functions rtl_w0w1_eri and rtl_w0w1_phy is somewhat misleading
regarding order of arguments. One could assume that w0w1 means
argument with bits to be reset comes before argument with bits to set.
However this is not the case.
So fix the order of arguments in several statements.
In addition fix EEE advertisement. The current code resets the bits
for 100BaseT and 1000BaseT EEE advertisement what is not what we want.
I have a little of a hard time to find a proper "Fixes" line as the
issue seems to have been there forever (at least it existed already
when the driver was moved to the current place in 2011).
The patch was tested on a Zotac Mini-PC with a RTL8111E-VL chip.
Before the patch EEE was disabled, now it's properly advertised and
works fine.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Revert regression inducing change to the IPSEC template resolver,
from Steffen Klassert.
2) Peeloffs can cause the wrong sk to be waken up in SCTP, fix from Xin
Long.
3) Min packet MTU size is wrong in cpsw driver, from Grygorii Strashko.
4) Fix build failure in netfilter ctnetlink, from Arnd Bergmann.
5) ISDN hisax driver checks pnp_irq() for errors incorrectly, from
Arvind Yadav.
6) Fix fealnx driver build failure on MIPS, from Huacai Chen.
7) Fix into leak in SCTP, the scope_id of socket addresses is not
always filled in. From Eric W. Biederman.
8) MTU inheritance between physical function and representor fix in nfp
driver, from Dirk van der Merwe.
9) Fix memory leak in rsi driver, from Colin Ian King.
10) Fix expiration and generation ID handling of cached ipv4 redirect
routes, from Xin Long.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (40 commits)
net: usb: hso.c: remove unneeded DRIVER_LICENSE #define
ibmvnic: fix dma_mapping_error call
ipvlan: NULL pointer dereference panic in ipvlan_port_destroy
route: also update fnhe_genid when updating a route cache
route: update fnhe_expires for redirect when the fnhe exists
sctp: set frag_point in sctp_setsockopt_maxseg correctly
rsi: fix memory leak on buf and usb_reg_buf
net/netlabel: Add list_next_rcu() in rcu_dereference().
nfp: remove false positive offloads in flower vxlan
nfp: register flower reprs for egress dev offload
nfp: inherit the max_mtu from the PF netdev
nfp: fix vlan receive MAC statistics typo
nfp: fix flower offload metadata flag usage
virto_net: remove empty file 'virtio_net.'
net/sctp: Always set scope_id in sctp_inet6_skb_msgname
fealnx: Fix building error on MIPS
isdn: hisax: Fix pnp_irq's error checking for setup_teles3
isdn: hisax: Fix pnp_irq's error checking for setup_sedlbauer_isapnp
isdn: hisax: Fix pnp_irq's error checking for setup_niccy
isdn: hisax: Fix pnp_irq's error checking for setup_ix1micro
...
This patch fixes the dma_mapping_error call to use the correct dma_addr
which is inside the ibmvnic_vpd struct. Moreover, it fixes an uninitialized
warning regarding a local dma_addr variable which is not used anymore.
Fixes: 4e6759be28 ("ibmvnic: Feature implementation of VPD for the ibmvnic driver")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Desnes A. Nunes do Rosario <desnesn@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass information to the match offload on whether or not the repr is the
ingress or egress dev. Only accept tunnel matches if repr is the egress
dev.
This means rules such as the following are successfully offloaded:
tc .. add dev vxlan0 .. enc_dst_port 4789 .. action redirect dev nfp_p0
While rules such as the following are rejected:
tc .. add dev nfp_p0 .. enc_dst_port 4789 .. action redirect dev vxlan0
Also reject non tunnel flows that are offloaded to an egress dev.
Non tunnel matches assume that the offload dev is the ingress port and
offload a match accordingly.
Fixes: 611aec101a ("nfp: compile flower vxlan tunnel metadata match fields")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register a callback for offloading flows that have a repr as their egress
device. The new egdev_register function is added to net-next for the 4.15
release.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PF netdev is used for data transfer for reprs, so reprs inherit the
maximum MTU settings of the PF netdev.
Fixes: 5de73ee467 ("nfp: general representor implementation")
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct typo in vlan receive MAC stats. Previously the MAC statistics
reported in ethtool for vlan receive contained a typo resulting in ethtool
reporting rx_vlan_reveive_ok instead of rx_vlan_received_ok.
Fixes: a5950182c0 ("nfp: map mac_stats and vf_cfg BARs")
Fixes: 098ce840c9 ("nfp: report MAC statistics in ethtool")
Reported-by: Brendan Galloway <brendan.galloway@netronome.com>
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hardware has no notion of new or last mask id, instead it makes use of the
message type (i.e. add flow or del flow) in combination with a single bit
in metadata flags to determine when to add or delete a mask id. Previously
we made use of the new or last flags to indicate that a new mask should be
allocated or deallocated, respectively. This incorrect behaviour is fixed
by making use single bit in metadata flags to indicate mask allocation or
deallocation.
Fixes: 43f84b72c5 ("nfp: add metadata to each flow offload")
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch try to fix the building error on MIPS. The reason is MIPS
has already defined the LONG macro, which conflicts with the LONG enum
in drivers/net/ethernet/fealnx.c.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge updates from Andrew Morton:
- a few misc bits
- ocfs2 updates
- almost all of MM
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (131 commits)
memory hotplug: fix comments when adding section
mm: make alloc_node_mem_map a void call if we don't have CONFIG_FLAT_NODE_MEM_MAP
mm: simplify nodemask printing
mm,oom_reaper: remove pointless kthread_run() error check
mm/page_ext.c: check if page_ext is not prepared
writeback: remove unused function parameter
mm: do not rely on preempt_count in print_vma_addr
mm, sparse: do not swamp log with huge vmemmap allocation failures
mm/hmm: remove redundant variable align_end
mm/list_lru.c: mark expected switch fall-through
mm/shmem.c: mark expected switch fall-through
mm/page_alloc.c: broken deferred calculation
mm: don't warn about allocations which stall for too long
fs: fuse: account fuse_inode slab memory as reclaimable
mm, page_alloc: fix potential false positive in __zone_watermark_ok
mm: mlock: remove lru_add_drain_all()
mm, sysctl: make NUMA stats configurable
shmem: convert shmem_init_inodecache() to void
Unify migrate_pages and move_pages access checks
mm, pagevec: rename pagevec drained field
...
As the page free path makes no distinction between cache hot and cold
pages, there is no real useful ordering of pages in the free list that
allocation requests can take advantage of. Juding from the users of
__GFP_COLD, it is likely that a number of them are the result of copying
other sites instead of actually measuring the impact. Remove the
__GFP_COLD parameter which simplifies a number of paths in the page
allocator.
This is potentially controversial but bear in mind that the size of the
per-cpu pagelists versus modern cache sizes means that the whole per-cpu
list can often fit in the L3 cache. Hence, there is only a potential
benefit for microbenchmarks that alloc/free pages in a tight loop. It's
even worse when THP is taken into account which has little or no chance
of getting a cache-hot page as the per-cpu list is bypassed and the
zeroing of multiple pages will thrash the cache anyway.
The truncate microbenchmarks are not shown as this patch affects the
allocation path and not the free path. A page fault microbenchmark was
tested but it showed no sigificant difference which is not surprising
given that the __GFP_COLD branches are a miniscule percentage of the
fault path.
Link: http://lkml.kernel.org/r/20171018075952.10627-9-mgorman@techsingularity.net
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now CPSW driver configures min eth packet size to 60 octets (ETH_ZLEN)
which works in most of cases, but when port VLAN is configured on some
switch port, it also can be configured to force all egress packets to be
VLAN untagged. And in this case, CPSW driver will pad small packets to 60
octets, but final packet size on port egress can became less than 60 octets
due to VLAN tag removal and packet will be dropped.
Hence, fix it by accounting VLAN header in CPSW min eth packet size. While
here, use proper defines for CPSW_MAX_PACKET_SIZE also, instead of open
coding.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace kmalloc followed by a memset with kzalloc
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Ariel Elior <aelior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Add iWARP support to qedr driver
- Lots of misc fixes across subsystem
- Multiple update series to hns roce driver
- Multiple update series to hfi1 driver
- Updates to vnic driver
- Add kref to wait struct in cxgb4 driver
- Updates to i40iw driver
- Mellanox shared pull request
- timer_setup changes
- massive cleanup series from Bart Van Assche
- Two series of SRP/SRPT changes from Bart Van Assche
- Core updates from Mellanox
- i40iw updates
- IPoIB updates
- mlx5 updates
- mlx4 updates
- hns updates
- bnxt_re fixes
- PCI write padding support
- Sparse/Smatch/warning cleanups/fixes
- CQ moderation support
- SRQ support in vmw_pvrdma
-----BEGIN PGP SIGNATURE-----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=A1oL
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma updates from Doug Ledford:
"This is a fairly plain pull request. Lots of driver updates across the
stack, a huge number of static analysis cleanups including a close to
50 patch series from Bart Van Assche, and a number of new features
inside the stack such as general CQ moderation support.
Nothing really stands out, but there might be a few conflicts as you
take things in. In particular, the cleanups touched some of the same
lines as the new timer_setup changes.
Everything in this pull request has been through 0day and at least two
days of linux-next (since Stephen doesn't necessarily flag new
errors/warnings until day2). A few more items (about 30 patches) from
Intel and Mellanox showed up on the list on Tuesday. I've excluded
those from this pull request, and I'm sure some of them qualify as
fixes suitable to send any time, but I still have to review them
fully. If they contain mostly fixes and little or no new development,
then I will probably send them through by the end of the week just to
get them out of the way.
There was a break in my acceptance of patches which coincides with the
computer problems I had, and then when I got things mostly back under
control I had a backlog of patches to process, which I did mostly last
Friday and Monday. So there is a larger number of patches processed in
that timeframe than I was striving for.
Summary:
- Add iWARP support to qedr driver
- Lots of misc fixes across subsystem
- Multiple update series to hns roce driver
- Multiple update series to hfi1 driver
- Updates to vnic driver
- Add kref to wait struct in cxgb4 driver
- Updates to i40iw driver
- Mellanox shared pull request
- timer_setup changes
- massive cleanup series from Bart Van Assche
- Two series of SRP/SRPT changes from Bart Van Assche
- Core updates from Mellanox
- i40iw updates
- IPoIB updates
- mlx5 updates
- mlx4 updates
- hns updates
- bnxt_re fixes
- PCI write padding support
- Sparse/Smatch/warning cleanups/fixes
- CQ moderation support
- SRQ support in vmw_pvrdma"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (296 commits)
RDMA/core: Rename kernel modify_cq to better describe its usage
IB/mlx5: Add CQ moderation capability to query_device
IB/mlx4: Add CQ moderation capability to query_device
IB/uverbs: Add CQ moderation capability to query_device
IB/mlx5: Exposing modify CQ callback to uverbs layer
IB/mlx4: Exposing modify CQ callback to uverbs layer
IB/uverbs: Allow CQ moderation with modify CQ
iw_cxgb4: atomically flush the qp
iw_cxgb4: only call the cq comp_handler when the cq is armed
iw_cxgb4: Fix possible circular dependency locking warning
RDMA/bnxt_re: report vlan_id and sl in qp1 recv completion
IB/core: Only maintain real QPs in the security lists
IB/ocrdma_hw: remove unnecessary code in ocrdma_mbx_dealloc_lkey
RDMA/core: Make function rdma_copy_addr return void
RDMA/vmw_pvrdma: Add shared receive queue support
RDMA/core: avoid uninitialized variable warning in create_udata
RDMA/bnxt_re: synchronize poll_cq and req_notify_cq verbs
RDMA/bnxt_re: Flush CQ notification Work Queue before destroying QP
RDMA/bnxt_re: Set QP state in case of response completion errors
RDMA/bnxt_re: Add memory barriers when processing CQ/EQ entries
...
Pull networking updates from David Miller:
"Highlights:
1) Maintain the TCP retransmit queue using an rbtree, with 1GB
windows at 100Gb this really has become necessary. From Eric
Dumazet.
2) Multi-program support for cgroup+bpf, from Alexei Starovoitov.
3) Perform broadcast flooding in hardware in mv88e6xxx, from Andrew
Lunn.
4) Add meter action support to openvswitch, from Andy Zhou.
5) Add a data meta pointer for BPF accessible packets, from Daniel
Borkmann.
6) Namespace-ify almost all TCP sysctl knobs, from Eric Dumazet.
7) Turn on Broadcom Tags in b53 driver, from Florian Fainelli.
8) More work to move the RTNL mutex down, from Florian Westphal.
9) Add 'bpftool' utility, to help with bpf program introspection.
From Jakub Kicinski.
10) Add new 'cpumap' type for XDP_REDIRECT action, from Jesper
Dangaard Brouer.
11) Support 'blocks' of transformations in the packet scheduler which
can span multiple network devices, from Jiri Pirko.
12) TC flower offload support in cxgb4, from Kumar Sanghvi.
13) Priority based stream scheduler for SCTP, from Marcelo Ricardo
Leitner.
14) Thunderbolt networking driver, from Amir Levy and Mika Westerberg.
15) Add RED qdisc offloadability, and use it in mlxsw driver. From
Nogah Frankel.
16) eBPF based device controller for cgroup v2, from Roman Gushchin.
17) Add some fundamental tracepoints for TCP, from Song Liu.
18) Remove garbage collection from ipv6 route layer, this is a
significant accomplishment. From Wei Wang.
19) Add multicast route offload support to mlxsw, from Yotam Gigi"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2177 commits)
tcp: highest_sack fix
geneve: fix fill_info when link down
bpf: fix lockdep splat
net: cdc_ncm: GetNtbFormat endian fix
openvswitch: meter: fix NULL pointer dereference in ovs_meter_cmd_reply_start
netem: remove unnecessary 64 bit modulus
netem: use 64 bit divide by rate
tcp: Namespace-ify sysctl_tcp_default_congestion_control
net: Protect iterations over net::fib_notifier_ops in fib_seq_sum()
ipv6: set all.accept_dad to 0 by default
uapi: fix linux/tls.h userspace compilation error
usbnet: ipheth: prevent TX queue timeouts when device not ready
vhost_net: conditionally enable tx polling
uapi: fix linux/rxrpc.h userspace compilation errors
net: stmmac: fix LPI transitioning for dwmac4
atm: horizon: Fix irq release error
net-sysfs: trigger netlink notification on ifalias change via sysfs
openvswitch: Using kfree_rcu() to simplify the code
openvswitch: Make local function ovs_nsh_key_attr_size() static
openvswitch: Fix return value check in ovs_meter_cmd_features()
...
Pull crypto updates from Herbert Xu:
"Here is the crypto update for 4.15:
API:
- Disambiguate EBUSY when queueing crypto request by adding ENOSPC.
This change touches code outside the crypto API.
- Reset settings when empty string is written to rng_current.
Algorithms:
- Add OSCCA SM3 secure hash.
Drivers:
- Remove old mv_cesa driver (replaced by marvell/cesa).
- Enable rfc3686/ecb/cfb/ofb AES in crypto4xx.
- Add ccm/gcm AES in crypto4xx.
- Add support for BCM7278 in iproc-rng200.
- Add hash support on Exynos in s5p-sss.
- Fix fallback-induced error in vmx.
- Fix output IV in atmel-aes.
- Fix empty GCM hash in mediatek.
Others:
- Fix DoS potential in lib/mpi.
- Fix potential out-of-order issues with padata"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (162 commits)
lib/mpi: call cond_resched() from mpi_powm() loop
crypto: stm32/hash - Fix return issue on update
crypto: dh - Remove pointless checks for NULL 'p' and 'g'
crypto: qat - Clean up error handling in qat_dh_set_secret()
crypto: dh - Don't permit 'key' or 'g' size longer than 'p'
crypto: dh - Don't permit 'p' to be 0
crypto: dh - Fix double free of ctx->p
hwrng: iproc-rng200 - Add support for BCM7278
dt-bindings: rng: Document BCM7278 RNG200 compatible
crypto: chcr - Replace _manual_ swap with swap macro
crypto: marvell - Add a NULL entry at the end of mv_cesa_plat_id_table[]
hwrng: virtio - Virtio RNG devices need to be re-registered after suspend/resume
crypto: atmel - remove empty functions
crypto: ecdh - remove empty exit()
MAINTAINERS: update maintainer for qat
crypto: caam - remove unused param of ctx_map_to_sec4_sg()
crypto: caam - remove unneeded edesc zeroization
crypto: atmel-aes - Reset the controller before each use
crypto: atmel-aes - properly set IV after {en,de}crypt
hwrng: core - Reset user selected rng by writing "" to rng_current
...
The LPI transitioning logic in stmmac_main uses
priv->tx_path_in_lpi_mode to enter/exit LPI.
However, priv->tx_path_in_lpi_mode is assigned
using the return value from host_irq_status().
So for dwmac4, priv->tx_path_in_lpi_mode was always false,
so stmmac_tx_clean() would always try to put us in eee mode,
and stmmac_xmit() would never take us out of eee mode.
To fix this, make host_irq_status() read and return the LPI
irq status also for dwmac4.
This also increments the existing LPI counters, so that
ethtool --statistics shows LPI transitions also for dwmac4.
For dwmac1000, irqs are enabled/disabled using the register
named "Interrupt Mask Register", and thus setting a bit disables
that specific irq.
For dwmac4 the matching register is named "MAC_Interrupt_Enable",
and thus setting a bit enables that specific irq.
Looking at dwmac1000_core.c, the irqs that are always enabled are:
LPI and PMT.
Looking at dwmac4_core.c, the irqs that are always enabled are:
PMT.
To be able to read the LPI irq status, we need to enable the LPI
irq also for dwmac4.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We accidentally return success if lio_vf_rep_modinit() fails instead of
propogating the error code.
Fixes: e20f469660 ("liquidio: synchronize VF representor names with NIC firmware")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements and enables VDP support for the ibmvnic driver.
Moreover, it includes the implementation of suitable structs, signal
transmission/handling and functions which allows the retrival of firmware
information from the ibmvnic card through the ethtool command.
Signed-off-by: Desnes A. Nunes do Rosario <desnesn@linux.vnet.ibm.com>
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvneta controller provides a 8-bit register to update the pending
Tx descriptor counter. Then, a maximum of 255 Tx descriptors can be
added at once. In the current code the mvneta_txq_pend_desc_add function
assumes the caller takes care of this limit. But it is not the case. In
some situations (xmit_more flag), more than 255 descriptors are added.
When this happens, the Tx descriptor counter register is updated with a
wrong value, which breaks the whole Tx queue management.
This patch fixes the issue by allowing the mvneta_txq_pend_desc_add
function to process more than 255 Tx descriptors.
Fixes: 2a90f7e1d5 ("net: mvneta: add xmit_more support")
Cc: stable@vger.kernel.org # 4.11+
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch migrates the HNS3 driver code from use of depricated PCI
MSI/MSI-X interrupt vector allocation/free APIs to new common APIs.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 4a3c67a6e7 ("mlxsw: spectrum_router: Don't batch neighbour
deletion") I removed the support for batch deletion of neighbours on a
router interface (RIF) since at that time the firmware did not support
it for IPv6 neighbours.
This is now supported by the version enforced by the driver, so there is
no reason to delete neighbours one by one anymore.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When "NETDEV WATCHDOG: em4 (bnx2x): transmit queue 2 timed out" occurs,
BNX2X_SP_RTNL_TX_TIMEOUT is set. In the function bnx2x_sp_rtnl_task,
bnx2x_nic_unload and bnx2x_nic_load are executed to shutdown and open
NIC. In the function bnx2x_nic_load, bnx2x_alloc_mem allocates dma
failure. The message "bnx2x: [bnx2x_alloc_mem:8399(em4)]Can't
allocate memory" pops out. The variable slowpath is set to NULL.
When shutdown the NIC, the function bnx2x_nic_unload is called. In
the function bnx2x_nic_unload, the following functions are executed.
bnx2x_chip_cleanup
bnx2x_set_storm_rx_mode
bnx2x_set_q_rx_mode
bnx2x_set_q_rx_mode
bnx2x_config_rx_mode
bnx2x_set_rx_mode_e2
In the function bnx2x_set_rx_mode_e2, the variable slowpath is operated.
Then the crash occurs.
To fix this crash, the variable slowpath is checked. And in the function
bnx2x_sp_rtnl_task, after dma memory allocation fails, another shutdown
and open NIC is executed.
CC: Joe Jin <joe.jin@oracle.com>
CC: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Acked-by: Ariel Elior <aelior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull timer updates from Thomas Gleixner:
"Yet another big pile of changes:
- More year 2038 work from Arnd slowly reaching the point where we
need to think about the syscalls themself.
- A new timer function which allows to conditionally (re)arm a timer
only when it's either not running or the new expiry time is sooner
than the armed expiry time. This allows to use a single timer for
multiple timeout requirements w/o caring about the first expiry
time at the call site.
- A new NMI safe accessor to clock real time for the printk timestamp
work. Can be used by tracing, perf as well if required.
- A large number of timer setup conversions from Kees which got
collected here because either maintainers requested so or they
simply got ignored. As Kees pointed out already there are a few
trivial merge conflicts and some redundant commits which was
unavoidable due to the size of this conversion effort.
- Avoid a redundant iteration in the timer wheel softirq processing.
- Provide a mechanism to treat RTC implementations depending on their
hardware properties, i.e. don't inflict the write at the 0.5
seconds boundary which originates from the PC CMOS RTC to all RTCs.
No functional change as drivers need to be updated separately.
- The usual small updates to core code clocksource drivers. Nothing
really exciting"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (111 commits)
timers: Add a function to start/reduce a timer
pstore: Use ktime_get_real_fast_ns() instead of __getnstimeofday()
timer: Prepare to change all DEFINE_TIMER() callbacks
netfilter: ipvs: Convert timers to use timer_setup()
scsi: qla2xxx: Convert timers to use timer_setup()
block/aoe: discover_timer: Convert timers to use timer_setup()
ide: Convert timers to use timer_setup()
drbd: Convert timers to use timer_setup()
mailbox: Convert timers to use timer_setup()
crypto: Convert timers to use timer_setup()
drivers/pcmcia: omap1: Fix error in automated timer conversion
ARM: footbridge: Fix typo in timer conversion
drivers/sgi-xp: Convert timers to use timer_setup()
drivers/pcmcia: Convert timers to use timer_setup()
drivers/memstick: Convert timers to use timer_setup()
drivers/macintosh: Convert timers to use timer_setup()
hwrng/xgene-rng: Convert timers to use timer_setup()
auxdisplay: Convert timers to use timer_setup()
sparc/led: Convert timers to use timer_setup()
mips: ip22/32: Convert timers to use timer_setup()
...
Pull scheduler updates from Ingo Molnar:
"The main updates in this cycle were:
- Group balancing enhancements and cleanups (Brendan Jackman)
- Move CPU isolation related functionality into its separate
kernel/sched/isolation.c file, with related 'housekeeping_*()'
namespace and nomenclature et al. (Frederic Weisbecker)
- Improve the interactive/cpu-intense fairness calculation (Josef
Bacik)
- Improve the PELT code and related cleanups (Peter Zijlstra)
- Improve the logic of pick_next_task_fair() (Uladzislau Rezki)
- Improve the RT IPI based balancing logic (Steven Rostedt)
- Various micro-optimizations:
- better !CONFIG_SCHED_DEBUG optimizations (Patrick Bellasi)
- better idle loop (Cheng Jian)
- ... plus misc fixes, cleanups and updates"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (54 commits)
sched/core: Optimize sched_feat() for !CONFIG_SCHED_DEBUG builds
sched/sysctl: Fix attributes of some extern declarations
sched/isolation: Document isolcpus= boot parameter flags, mark it deprecated
sched/isolation: Add basic isolcpus flags
sched/isolation: Move isolcpus= handling to the housekeeping code
sched/isolation: Handle the nohz_full= parameter
sched/isolation: Introduce housekeeping flags
sched/isolation: Split out new CONFIG_CPU_ISOLATION=y config from CONFIG_NO_HZ_FULL
sched/isolation: Rename is_housekeeping_cpu() to housekeeping_cpu()
sched/isolation: Use its own static key
sched/isolation: Make the housekeeping cpumask private
sched/isolation: Provide a dynamic off-case to housekeeping_any_cpu()
sched/isolation, watchdog: Use housekeeping_cpumask() instead of ad-hoc version
sched/isolation: Move housekeeping related code to its own file
sched/idle: Micro-optimize the idle loop
sched/isolcpus: Fix "isolcpus=" boot parameter handling when !CONFIG_CPUMASK_OFFSTACK
x86/tsc: Append the 'tsc=' description for the 'tsc=unstable' boot parameter
sched/rt: Simplify the IPI based RT balancing logic
block/ioprio: Use a helper to check for RT prio
sched/rt: Add a helper to test for a RT task
...
Pull core locking updates from Ingo Molnar:
"The main changes in this cycle are:
- Another attempt at enabling cross-release lockdep dependency
tracking (automatically part of CONFIG_PROVE_LOCKING=y), this time
with better performance and fewer false positives. (Byungchul Park)
- Introduce lockdep_assert_irqs_enabled()/disabled() and convert
open-coded equivalents to lockdep variants. (Frederic Weisbecker)
- Add down_read_killable() and use it in the VFS's iterate_dir()
method. (Kirill Tkhai)
- Convert remaining uses of ACCESS_ONCE() to
READ_ONCE()/WRITE_ONCE(). Most of the conversion was Coccinelle
driven. (Mark Rutland, Paul E. McKenney)
- Get rid of lockless_dereference(), by strengthening Alpha atomics,
strengthening READ_ONCE() with smp_read_barrier_depends() and thus
being able to convert users of lockless_dereference() to
READ_ONCE(). (Will Deacon)
- Various micro-optimizations:
- better PV qspinlocks (Waiman Long),
- better x86 barriers (Michael S. Tsirkin)
- better x86 refcounts (Kees Cook)
- ... plus other fixes and enhancements. (Borislav Petkov, Juergen
Gross, Miguel Bernal Marin)"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (70 commits)
locking/x86: Use LOCK ADD for smp_mb() instead of MFENCE
rcu: Use lockdep to assert IRQs are disabled/enabled
netpoll: Use lockdep to assert IRQs are disabled/enabled
timers/posix-cpu-timers: Use lockdep to assert IRQs are disabled/enabled
sched/clock, sched/cputime: Use lockdep to assert IRQs are disabled/enabled
irq_work: Use lockdep to assert IRQs are disabled/enabled
irq/timings: Use lockdep to assert IRQs are disabled/enabled
perf/core: Use lockdep to assert IRQs are disabled/enabled
x86: Use lockdep to assert IRQs are disabled/enabled
smp/core: Use lockdep to assert IRQs are disabled/enabled
timers/hrtimer: Use lockdep to assert IRQs are disabled/enabled
timers/nohz: Use lockdep to assert IRQs are disabled/enabled
workqueue: Use lockdep to assert IRQs are disabled/enabled
irq/softirqs: Use lockdep to assert IRQs are disabled/enabled
locking/lockdep: Add IRQs disabled/enabled assertion APIs: lockdep_assert_irqs_enabled()/disabled()
locking/pvqspinlock: Implement hybrid PV queued/unfair locks
locking/rwlocks: Fix comments
x86/paravirt: Set up the virt_spin_lock_key after static keys get initialized
block, locking/lockdep: Assign a lock_class per gendisk used for wait_for_completion()
workqueue: Remove now redundant lock acquisitions wrt. workqueue flushes
...
In xmit process, the variables are set many times. In fact,
it is enough for these variables to be set once.
After a long time test, the throughput performance is better
than before.
CC: Srinivas Eeda <srinivas.eeda@oracle.com>
CC: Joe Jin <joe.jin@oracle.com>
CC: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since Mellanox focus is on newer adapters, we would like to have the
ability to disable the support for old gen2 adapters.
This can be done by turning off the MLX4_CORE_GEN2 Kconfig flag.
We keep it turned on by default.
Signed-off-by: Slava Shwartsman <slavash@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable giga_ctrl is being assigned to zero however this is
never read and hence the assignment is redundant, so remove it.
Cleans up clang warning:
drivers/net/ethernet/realtek/r8169.c:1978:3: warning: Value stored
to 'giga_ctrl' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for enabling Broadcom tags with b53, pad packets to a
minimum size of 64 bytes (sans FCS) in order for the Broadcom switch to
accept ingressing frames. Without this, we would typically be able to
DHCP, but not resolve with ARP because packets are too small and get
rejected by the switch.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes an error in memory allocation/freeing in
ThunderX PF driver.
I moved the allocation to the probe() function and made it managed.
>From the Colin's email:
While running static analysis on linux-next with CoverityScan I found 3
double free errors in the Cavium thunder driver.
The issue occurs on the err_disable_device: label of function nic_probe
when nic_free_lmacmem(nic) is called and a double free occurs on
nic->duplex, nic->link and nic->speed. This occurs when nic_init_hw()
fails:
/* Initialize hardware */
err = nic_init_hw(nic);
if (err)
goto err_release_regions;
nic_init_hw() calls nic_get_hw_info() and this calls nic_free_lmacmem()
if any of the allocations fail. This free'ing occurs again by the call
to nic_free_lmacmem() on the err_release_regions exit path in nic_probe().
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable start is assigned but never read hence it is redundant
and can be removed. Cleans up clang warning:
drivers/net/ethernet/sfc/ptp.c:655:2: warning: Value stored to 'start'
is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The assignment to mbcp is identical to the initiatialized value assigned
to mbcp at declaration time a few lines earlier, hence we can remove the
second redundant assignment. Cleans up clang warning:
drivers/net/ethernet/qlogic/qlge/qlge_mpi.c:209:22: warning:
Value stored to 'mbcp' during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114888
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114891
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1397960
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1397972
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the login buffer to include client data for the vnic driver,
this includes the OS name, LPAR name, and device name. This update
allows this information to be available in the VIOS.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We add the call of_node_put(bp->phy_node) to all associated error
paths for memory clean up.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We add the call of_phy_deregister_fixed_link to all associated
error paths for memory clean up.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GOP statistics from all ports of one instance of the driver are gathered
with one work recalled in loop in a workqueue. The loop is started when
a port is up, and stopped when a port is down. This last condition is
obviously wrong.
Fix this by having a work per port. This way, starting and stoping it
when the port is up or down will be fine, while minimizing unnecessary
CPU usage.
Fixes: 118d6298f6 ("net: mvpp2: add ethtool GOP statistics")
Reported-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When checking whether auto-negotiation is on, driver only needs to
check the value of mac.autoneg(SW) directly, and does not need to
query it from hardware. Because this value is always synchronized
with the auto-negotiation state of hardware.
This patch removes mac auto-negotiation state query in
hclge_update_speed_duplex().
Fixes: 46a3df9f97 (net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support)
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver gets phy address from NCL_config file and uses the phy address
to initialize phydev. There are 5 bits for phy address. And C22 phy
address has 5 bits. So 0-31 are all valid address for phy. If there
is no phy, it will crash. Because driver always get a valid phy address.
This patch fixes the phy address to 8 bits, and use 0xff to indicate
invalid phy address.
Fixes: 46a3df9f97 (net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support)
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is to prevent the case of working with a single MPWQE
(1 WQE is always reserved as RQ is linked-list).
When the WQE is fully consumed, HW should still have available buffer
in order not to drop packets.
Fixes: 461017cb00 ("net/mlx5e: Support RX multi-packet WQE (Striding RQ)")
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently, when dma mapping fails, put_page is called,
but the page is not set to null. Later, in the page_reuse treatment in
mlx5e_free_rx_descs(), mlx5e_page_release() is called for the second time,
improperly doing dma_unmap (for a non-mapped address) and an extra put_page.
Prevent this by nullifying the page pointer when dma_map fails.
Fixes: accd588332 ("net/mlx5e: Introduce RX Page-Reuse")
Signed-off-by: Inbar Karmy <inbark@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
napi->poll can be called with budget 0, e.g. in netpoll scenarios
where the caller only wants to poll TX rings
(poll_one_napi@net/core/netpoll.c).
The below commit changed RX polling from "while" loop to "do {} while",
which caused to ignore the initial budget and handle at least one RX
packet.
This fixes the following warning:
[ 2852.049194] mlx5e_napi_poll+0x0/0x260 [mlx5_core] exceeded budget in poll
[ 2852.049195] ------------[ cut here ]------------
[ 2852.049195] WARNING: CPU: 0 PID: 25691 at net/core/netpoll.c:171 netpoll_poll_dev+0x18a/0x1a0
Fixes: 4b7dfc9925 ("net/mlx5e: Early-return on empty completion queues")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Reported-by: Martin KaFai Lau <kafai@fb.com>
Tested-by: Martin KaFai Lau <kafai@fb.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
After the panic teardown firmware command, health_care detects the error
in PCI bus and calls the mlx5_pci_err_detected. This health_care flow is
no longer needed because the panic teardown firmware command will bring
down the PCI bus communication with the HCA.
The solution is to cancel the health care timer and its pending
workqueue request before sending panic teardown firmware command.
Kernel trace:
mlx5_core 0033:01:00.0: Shutdown was called
mlx5_core 0033:01:00.0: health_care:154:(pid 9304): handling bad device here
mlx5_core 0033:01:00.0: mlx5_handle_bad_state:114:(pid 9304): NIC state 1
mlx5_core 0033:01:00.0: mlx5_pci_err_detected was called
mlx5_core 0033:01:00.0: mlx5_enter_error_state:96:(pid 9304): start
mlx5_3:mlx5_ib_event:3061:(pid 9304): warning: event on port 0
mlx5_core 0033:01:00.0: mlx5_enter_error_state:104:(pid 9304): end
Unable to handle kernel paging request for data at address 0x0000003f
Faulting instruction address: 0xc0080000434b8c80
Fixes: 8812c24d28 ('net/mlx5: Add fast unload support in shutdown flow')
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
list_splice_init initializing waiting_events_list after splicing it to
temp list, therefore we should loop over temp list to fire the events.
Fixes: 4ca637a20a ("net/mlx5: Delay events till mlx5 interface's add complete for pci resume")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Modified netronome nfp flower action to use VLAN helper functions instead
of accessing/referencing TC act_vlan private structures directly.
Reviewed-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: Manish Kurup <manish.kurup@verizon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: 535a61777f ("sfc: suppress handled MCDI failures when changing the MAC address")
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are several pointers that are being assigned but never read
so remove these as they are redundant. Also remove an assignment
to function_mode that is never read. Cleans up several clang
warnings:
vxge-main.c:1139:2: warning: Value stored to 'hldev' is never read
vxge-main.c:1294:2: warning: Value stored to 'hldev' is never read
vxge-main.c:2188:2: warning: Value stored to 'dev' is never read
vxge-main.c:2188:2: warning: Value stored to 'dev' is never read
vxge-main.c:2723:2: warning: Value stored to 'function_mode' is
never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed says:
====================
mlx5-updates-2017-11-09
This series introduces vlan offloads related improvements for mlx5
ethernet netdev driver, from Gal Pressman.
- Add support for 802.1ad vlan filter
- Add support for 802.1ad vlan insertion
- Add vlan offloads statistics to ethtool (inserted/stripped vlans)
- CHECKSUM_COMPLETE support for vlan traffic when vlan stripping is off! (Finally)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple cases of overlapping changes in the packet scheduler.
Must easier to resolve this time.
Which probably means that I screwed it up somehow.
Signed-off-by: David S. Miller <davem@davemloft.net>
When the VLAN tag is present in the packet buffer (i.e VLAN stripping disabled, QinQ)
the driver will currently report CHECKSUM_UNNECESSARY.
Instead of using CHECKSUM_COMPLETE offload for packets with first
ethertype of IPv4/6, use it for packets with last ethertype of IPv4/6 to
cover the former cases as well.
The checksum field present in the CQE is calculated from the IP header
until the end of the packet. When the first ethertype is different than
IPv4/6 (for ex. 802.1Q VLAN) a checksum of the VLAN header/s should be
added. The small header/s checksum calculation will allow us to use
CHECKSUM_COMPLETE instead of CHECKSUM_UNNECESSARY.
Testing bandwidth of one and 8 TCP streams to a single RQ,
LRO and VLAN stripping offloads disabled:
CPU: Intel(R) Xeon(R) CPU E5-2660 v2 @ 2.20GHz
NIC: Mellanox Technologies MT27710 Family [ConnectX-4 Lx]
Before:
+--------------+--------------------+---------------------+----------------------+
| Traffic type | 1 Stream BW [Mbps] | 8 Streams BW [Mbps] | Checksum offload |
+--------------+--------------------+---------------------+----------------------+
| Untagged | 28,247.35 | 24,716.88 | CHECKSUM_COMPLETE |
| VLAN | 27,516.69 | 23,752.26 | CHECKSUM_UNNECESSARY |
| QinQ | 6,961.30 | 20,667.04 | CHECKSUM_UNNECESSARY |
+--------------+--------------------+---------------------+----------------------+
Now:
+--------------+--------------------+---------------------+-------------------+
| Traffic type | 1 Stream BW [Mbps] | 8 Streams BW [Mbps] | Checksum offload |
+--------------+--------------------+---------------------+-------------------+
| Untagged | 28,521.28 | 24,926.32 | CHECKSUM_COMPLETE |
| VLAN | 27,389.37 | 23,715.34 | CHECKSUM_COMPLETE |
| QinQ | 6,901.77 | 20,845.73 | CHECKSUM_COMPLETE |
+--------------+--------------------+---------------------+-------------------+
No performance degradation observed.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The following counters are now exposed through ethtool -S:
rx[i]_removed_vlan_packets (per channel)
rx_removed_vlan_packets
tx[i]_added_vlan_packets (per channel)
tx_added_vlan_packets
rx_removed_vlan_packets: The number of packets that had their
outer VLAN header stripped to the CQE by the hardware.
tx_added_vlan_packets: The number of packets that had their
outer VLAN header inserted by the hardware.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Report VLAN insertion support for S-tagged packets and add support by
choosing the correct VLAN type in the WQE.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When a user chooses to use 802.1ad VLAN the proper steering rules will
be added to the VLAN flow table (matching the specific S-tag VID).
Due to current hardware limitation, when using 802.1ad, we must disable
C-tag VLAN stripping on the RQs.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When add VLAN rule fails the active vlan bit should be cleared.
Fixes: afb736e933 ("net/mlx5: Ethernet resource handling files")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Rename VLAN related symbols to better reflect the fact that they
are associated to C-tag VLAN.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add ethtool statistics support by reading the GOP statistics from the
hardware counters. Also implement a workqueue to gather the statistics
every second or some 32-bit counters could overflow.
Suggested-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Memory allocation functions already display some informaton in case of
memory allocation failure. There is no need to add an extra 'dev_err' here.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
If 'of_phy_find_device()' fails, we must undo the previous 'of_node_get()'
call, as done the the following error handling code.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to release explicitly some devm_ allocated resources.
If the 'mac_probe()' probe function fails, they will be released
automatically, as already done in the other error handling paths of
this function.
Also goto '_return_of_get_parent' as in the other error handling paths.
This is useless (priv->fixed_link is NULL at this point), but at least
it is consistent.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit c6e26ea8c8 ("dpaa_eth: change device used") has removed usage of
'dev_set_drvdata()' in the 'mac_probe() function.
This call should also be axed.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
On 32-bit architectures, rtc_time_to_tm() returns incorrect results
in 2038 or later, and do_gettimeofday() is broken for the same reason.
This changes the code to use ktime_get_real_seconds() and time64_to_tm()
instead, both of them are 2038-safe, and we can also get rid of the
CONFIG_RTC_LIB dependency that way.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We return on the previous line so this "return 0;" statement should just
be deleted.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return a negative error code from the VID create error handling
case instead of 0, as done elsewhere in this function.
Fixes: c57529e1d5 ("mlxsw: spectrum: Replace vPorts with Port-VLAN")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return a negative error code from the dpaa_bp_alloc() error
handling case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for ndo_setup_tc with enum tc_setup_type value of
TC_SETUP_QDISC_STATS. This call updates the generic qdisc stats from the
cache if the handle ID that is asked for matching the root qdisc ID and
fails otherwise.
Currently doesn't support qlen and rqueues.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for ndo_setup_tc with enum tc_setup_type value of
TC_SETUP_RED_XSTATS. This call returns the RED qdisc xstats from the cache
if the handle ID that is asked for matching the root qdisc ID and fails
otherwise.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add more statistics to be collected from the HW periodically. These stats
are tclass based (beside ECN marked packet, that exist only port based).
They are needed to expose RED qdisc stats and xstats correctly.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the counter group definitions for 2 new counter groups
which are necessary for gaining ECN & wred counters.
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for ndo_setup_tc with enum tc_setup_type value of TC_SETUP_RED.
This call sets RED qdisc on a traffic class.
This patch supports RED qdisc only as a root qdisc and set in on the
default tclass. It can be set with or without ECN.
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds 2 new registers:
- Congestion WRED ECN TClass Profile Register [CWTP]
- Congestion WRED ECN TClass and Pool Mapping Register [CWTPM]
These registers would later be needed to offload RED-related
functionality to the HW.
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change TC_SETUP_CBS to TC_SETUP_QDISC_CBS to match the new convention..
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change TC_SETUP_MQPRIO to TC_SETUP_QDISC_MQPRIO to match the new
convention.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hn is being kfree'd in mlx5e_del_l2_from_hash and then dereferenced
by accessing hn->ai.addr
Fix this by copying the MAC address into a local variable for its safe use
in all possible execution paths within function mlx5e_execute_l2_action.
Addresses-Coverity-ID: 1417789
Fixes: eeb66cdb68 ("net/mlx5: Separate between E-Switch and MPFS")
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is better for code locality and should slightly
speed up normal interrupts.
This also allows PPS clock output to start working for
i.mx7. This is because i.mx7 was already using the limit
of 3 interrupts, and needed another.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvpp2 driver can't cope at all with the TX affinities being
changed from userspace, and spit an endless stream of
[ 91.779920] mvpp2 f4000000.ethernet eth2: wrong cpu on the end of Tx processing
[ 91.779930] mvpp2 f4000000.ethernet eth2: wrong cpu on the end of Tx processing
[ 91.780402] mvpp2 f4000000.ethernet eth2: wrong cpu on the end of Tx processing
[ 91.780406] mvpp2 f4000000.ethernet eth2: wrong cpu on the end of Tx processing
[ 91.780415] mvpp2 f4000000.ethernet eth2: wrong cpu on the end of Tx processing
[ 91.780418] mvpp2 f4000000.ethernet eth2: wrong cpu on the end of Tx processing
rendering the box completely useless (I've measured around 600k
interrupts/s on a 8040 box) once irqbalance kicks in and start
doing its job.
Obviously, the driver was never designed with this in mind. So let's
work around the problem by preventing userspace from interacting
with these interrupts altogether.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed says:
====================
mlx5-updates-2017-11-04
This series includes:
From Huy: dscp to priority mapping for Ethernet packet.
===================================================
First six patches enable differentiated services code point (dscp) to
priority mapping for Ethernet packet. Once this feature is
enabled, the packet is routed to the corresponding priority based on its
dscp. User can combine this feature with priority flow control (pfc)
feature to have priority flow control based on the dscp.
Firmware interface:
Mellanox firmware provides two control knobs for this feature:
QPTS register allow changing the trust state between dscp and
pcp mode. The default is pcp mode. Once in dscp mode, firmware will
route the packet based on its dscp value if the dscp field exists.
QPDPM register allow mapping a specific dscp (0 to 63) to a
specific priority (0 to 7). By default, all the dscps are mapped to
priority zero.
Software interface:
This feature is controlled via application priority TLV. IEEE
specification P802.1Qcd/D2.1 defines priority selector id 5 for
application priority TLV. This APP TLV selector defines DSCP to priority
map. This APP TLV can be sent by the switch or can be set locally using
software such as lldptool. In mlx5 drivers, we add the support for net
dcb's getapp and setapp call back. Mlx5 driver only handles the selector
id 5 application entry (dscp application priority application entry).
If user sends multiple dscp to priority APP TLV entries on the same
dscp, the last sent one will take effect. All the previous sent will be
deleted.
The firmware trust state (in QPTS register) is changed based on the
number of dscp to priority application entries. When the first dscp to
priority application entry is added by the user, the trust state is
changed to dscp. When the last dscp to priority application entry is
deleted by the user, the trust state is changed to pcp.
When the port is in DSCP trust state, the transmit queue is selected
based on the dscp of the skb.
When the port is in DSCP trust state and vport inline mode is not NONE,
firmware requires mlx5 driver to copy the IP header to the
wqe ethernet segment inline header if the skb has it.
This is done by changing the transmit queue sq's min inline mode to L3.
Note that the min inline mode of sqs that belong to other features
such as xdpsq, icosq are not modified.
===================================================
Plus to the dscp series, some small misc changes are include as well:
From Inbar, Ethtool msglvl support and some debug prints in DCBNL logic
From Or Gerlitz, Enlarge the NIC TC offload table size
From Rabie, Initialize destination_flow struct to 0
From Feras, Add inner TTC table to IPoIB flow steering
From Tal, Enable CQE based moderation on TX CQ
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support in the driver ethtool ops to modify the NFP FEC modes.
The FEC modes can be set for vNIC associated with physical ports or
for MAC representor netdevs.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement helpers to determine and modify FEC modes via the NSP.
The NSP advertises FEC capabilities on a per port basis and provides
support for:
* Auto mode selection
* Reed Solomon
* BaseR
* None/Off
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since it is now safe to modify link settings for representors, we can
attach the get/set link settings ndos to it. The get/set link settings
are nfp_port based operations.
If a port becomes invalid, the representor will be removed in the same
way a vnic would be.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the NSP port table has been refreshed, resync the representor state
with the new port information. At the moment, this only entails looking
for invalid ports and killing off representors associated with them.
The repr instance becomes NULL which is safe since the app accessor
function for reprs returns NULL when it cannot access a repr.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The criteria that reprs cannot be replaced with another new set of reprs
has been removed. This check is not needed since the only use case that
could exercise this at the moment, would be to modify the number of
SRIOV VFs without first disabling them. This case is explicitly
disallowed in any case and subsequent patches in this series
need to be able to replace the running set of reprs.
All cases where the return code used to be checked for the
nfp_app_reprs_set function have been removed.
As stated above, it is not possible for the current code to encounter a
case where reprs exist and need to be replaced.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent management FW images can perform full reinit of MAC cores
without requiring a reboot. When loading the driver check if there
are changes pending and if so call NSP MAC reinit. Full application
FW reload is still required, and all MACs need to be reinited at the
same time (not only the ones which have been reconfigured, and thus
potentially causing disruption to unrelated netdevs) therefore for
now changing MAC config without reloading the driver still remains
future work.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Tested-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matthias reports:
nfp_eth_set_bit_config() is marked as __always_inline to allow gcc to
identify the 'mask' parameter as known to be constant at compile time,
which is required to use the FIELD_GET() macro.
The forced inlining does the trick for gcc, but for kernel builds with
clang it results in undefined symbols:
drivers/net/ethernet/netronome/nfp/nfpcore/nfp_nsp_eth.o: In function
`__nfp_eth_set_aneg':
drivers/net/ethernet/netronome/nfp/nfpcore/nfp_nsp_eth.c:(.text+0x787):
undefined reference to `__compiletime_assert_492'
drivers/net/ethernet/netronome/nfp/nfpcore/nfp_nsp_eth.c:(.text+0x7b1):
undefined reference to `__compiletime_assert_496'
These __compiletime_assert_xyx() calls would have been optimized away
if
the compiler had seen 'mask' as a constant.
Add a macro to extract the mask and shift and pass those to
nfp_eth_set_bit_config() separately.
Reported-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Tested-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netdev->rx_dropped was including packets dropped by napi_gro_receive.
If a packet is dropped by network stack, it should not be counted under
driver Rx dropped.
Made necessary changes to not include network stack drops under
netdev->rx_dropped.
Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com>
Signed-off-by: Satanand Burla <satananda.burla@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following steps are taken in the driver to offload an XDP program:
XDP_SETUP_PROG:
* prepare:
- allocate program state;
- run verifier (bpf_analyzer());
- run translation;
* load:
- stop old program if needed;
- load program;
- enable BPF if not enabled;
* clean up:
- free program image.
With new infrastructure the flow will look like this:
BPF_OFFLOAD_VERIFIER_PREP:
- allocate program state;
BPF_OFFLOAD_TRANSLATE:
- run translation;
XDP_SETUP_PROG:
- stop old program if needed;
- load program;
- enable BPF if not enabled;
BPF_OFFLOAD_DESTROY:
- free program image.
Take advantage of the new infrastructure. Allocation of driver
metadata has to be moved from jit.c to offload.c since it's now
done at a different stage. Since there is no separate driver
private data for verification step, move temporary nfp_meta
pointer into nfp_prog. We will now use user space context
offsets.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct nfp_prog is currently only used internally by the translator.
This means there is a lot of parameter passing going on, between
the translator and different stages of offload. Simplify things
by allocating nfp_prog in offload.c already.
We will now use kmalloc() to allocate the program area and only
DMA map it for the time of loading (instead of allocating DMA
coherent memory upfront).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of offload/translation prepare logic will be moved to
offload.c. To help git generate more reasonable diffs
move nfp_prog_prepare() and nfp_prog_free() functions
there as a first step.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware supports live replacement of programs for quite some
time now. Remove the software-fallback related logic and
depend on the FW for program replace. Seamless reload will
become a requirement if maps are present, anyway.
Load and start stages have to be split now, since replace
only needs a load, start has already been done on add.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently create a fake cls_bpf offload object when we want
to offload XDP. Simplify and clarify the code by moving the
TC/XDP specific logic out of common offload code. This is easy
now that we don't support legacy TC actions. We only need the
bpf program and state of the skip_sw flag.
Temporarily set @code to NULL in nfp_net_bpf_offload(), compilers
seem to have trouble recognizing it's always initialized. Next
patches will eliminate that variable.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BPF offload's main header does not need to include nfp_net.h.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The register renumbering was removed and will not be coming back
in its old, naive form, given that it would be fundamentally
incompatible with calling functions. Remove the leftovers.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only support BPF_PROG_TYPE_SCHED_CLS programs in direct
action mode. This simplifies preparing the offload since
there will now be only one mode of operation for that type
of program. We need to know the attachment mode type of
cls_bpf programs, because exit codes are interpreted
differently for legacy vs DA mode.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ndo_xdp is a control path callback for setting up XDP in the
driver. We can reuse it for other forms of communication
between the eBPF stack and the drivers. Rename the callback
and associated structures and definitions.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can now build this driver on ARM, so I ran into a randconfig build
warning that presumably had existed on powerpc already.
drivers/net/ethernet/freescale/dpaa/dpaa_eth.c: In function 'sg_fd_to_skb':
drivers/net/ethernet/freescale/dpaa/dpaa_eth.c:1712:18: error: 'skb' may be used uninitialized in this function [-Werror=maybe-uninitialized]
I'm slightly changing the logic here, to make it obvious to the
compiler that 'skb' is always initialized.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
By using CQE based moderation on TX CQ we can reduce the number of TX
interrupt rate. Besides the benefit of less interrupts, this also
allows the kernel to better utilize TSO. Since TSO has some CPU overhead,
it might not aggregate when CPU is under high stress. By reducing the
interrupt rate and the CPU utilization, we can get better aggregation
and better overall throughput.
The feature is enabled by default and has a private flag in ethtool
for control.
Throughput, interrupt rate and TSO utilization improvements:
(ConnectX-4Lx 40GbE, unidirectional, 1/16 TCP streams, 64B packets)
---------------------------------------------------------
Metric | Streams | CQE Based | EQE Based | improvement
---------------------------------------------------------
BW | 1 | 2.4Gb/s | 2.15Gb/s | +11.6%
IR | 1 | 27Kips | 50.6Kips | -46.7%
TSO Util | 1 | 74.6% | 71% | +5%
BW | 16 | 29Gb/s | 25.85Gb/s | +12.2%
IR | 16 | 482Kips | 745Kips | -35.3%
TSO Util | 16 | 69.1% | 49% | +41.1%
*BW = Bandwidth, IR = Interrupt rate, ips = interrupt per second.
TSO Util = bytes in TSO sessions / all bytes transferred
Signed-off-by: Tal Gilboa <talgi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Zhu Yanjun