Simplify the code a bit more by extracting the rates table
building logic into a separate function and handle setting
a fixed rate for debug in a separate flow.
Also avoid using and saving ucode rate format in different
places. Instead use rs_rate struct and convert to ucode format
only when filling the rates table in the LQ command.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Current firmware doesn't handle well uAPSD in P2P Client.
When it will be fixed, the firmware will set a TLV flag to notify
the driver that uAPSD is supported in P2P client mode.
Check this flag when sending power command for P2P client.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
It is not currently implemented for SDIO, and not required for other slave
buses as well.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Clear the FW_ERROR status before the common start_fw transport code.
Remove the transport specific clears.
After these patches the FW_ERROR flag is only set and cleared by common
transport code.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In case a sync command timeouts or Tx is stuck while a FW error
interrupt arrives, we might call iwl_op_mode_nic_error twice before
a restart has been initiated. This will cause a reprobe. Unify calls
to this function at the transport level and only call it on the first
FW error in a given by checking the transport FW error flag.
While at it, remove the privately defined iwl_nic_error from PCIE code
and use the common callback instead.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Move rs_program_fix_rate right before it's caller where we're
already in the context of an ifdef CPTCFG_MAC80211_DEBUGFS so
we can get rid of the extra ifdefs surrounding the original
location.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Stop Tx and commands from arriving to the transport layer when a FW
error has occurred. A HW recovery should take place before. Remove
transport specific checks of the same nature (note that not all
transports were protected).
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The same bits are employed in all transport layers. Put the status
field in the common transport layer. This allows us to employ them
in common transport code.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The stop_hw trans callback is not well defined. It is missing in many
cleanup flows and the division of labor between stop_device/stop_hw
is cumbersome. Remove stop_hw and use stop_device to perform both.
Implement this for all current transports.
PCIE needs some extra configuration the op-mode is leaving to configure
RF kill. Expose this explicitly as a new op_mode_leave trans callback.
Take the call to stop_device outside iwl_run_mvm_init_ucode, this
makes more sense and WARN when we want to run the INIT firmware while
it has run already.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The documentation for smps_requests is unclear, rewrite it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Configure the phy context to the minimum required
bandwidth, given by ctx->min_def.
Tuning to a narrower bandwidth should reduce the
noise level and consume less power.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Configure the fw to filter multicast according to
the addresses given by mac80211.
Note that bssid should be given even if we want
to pass all the multicast frames.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This allows to tweak the power parameters per vif.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Enable power save on P2P client interface only if it is the
only bound interface.
Avoid using uAPSD if P2P client is associated to GO that uses
opportunistic power save. This is due to current FW limitation.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When monitor interface is activated device power save needs
to be disabled.
Re-consider power management status on other active
interfaces when monitor interface is bound or unbound.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
FW still does not support power management on multiple MAC interfaces.
Currently the driver enforce this limitation by disabling PM if second
interface is added. Change this behavior to allow PM on a single interface
even if other interfaces exist but not bound to any specific PHY.
PM will be enabled if only one single interface is bound.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
FW implements protective algorithm to identify AP's improper uAPSD
behavior. FW sends misbehaving AP notification in this case.
Add this notification handling. Avoid using uAPSD in next association
to the exactly same AP. Refactor iwl_mvm_power_build_cmd() to move
uAPSD related code to a separate function.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
If the device is MIMO and VHT capable it supports Tx STBC.
Unlike HT, any chip that supports VHT also support STBC so
no need for a config parameter.
Using num_of_ants multiple times warranted caching it.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
It was set to zero which reflects support of a single STS.
Set according to the number of Rx antennas which correctly
reflects the number of STSs the STA can receive in a VHT NDP.
This improves beamforming and has been tested to improve Rx
throughput.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Not all chips support STBC so allow this to be
another config parameter per chip type. If STBC
is supported then publish it in the HT caps.
Since 7260/7265/3160 chips support it - set the stbc
support bit.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This patch adds a cipher scheme support to extend a set of
the supported ciphers. The driver reads a cipher scheme list TLV
from FW image and passes it to mac80211 on hw registration.
After the cipher schemes are registered the driver handles key
installation and Tx/Rx calls related to the new ciphers.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Send firmware a Smart FIFO Configuration host command to allow
interrupt coalescing. The smart FIFO is enabled when there is
only one bound interface (other than p2p devices which are
ignored) and it is of type station, and activated while the
station is associated.
Smart Fifo allows aggragations of DMA transactions and by that
causes processor and memory controller to stay for a longer time
on lower c-states, thus saving platform power.
Firmware relies on driver to activate and disable it.
Signed-off-by: Lilach Edelstein <lilach.edelstein@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Products that have only 1 antenna in Rx don't support MIMO
in RX. As a consequence, they will be in STATIC always.
Don't tell mac80211 to update SMPS in that case. mac80211
would send an action frame to the AP which is clearly
bogus.
As a matter of fact, we have seen that some APs send a
deauth when that happens.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Sync to SCO is a feature that allows to synchronise the
wifi activity with the predictable BT activity in
SCO profile. This allows to reduce the collisions and
improve overall quality.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Rewrite the search cycle state machine to use a more data
oriented approach where the different Tx columns (configs)
limitations and next columns to search are reprsented in
tables which are easy to change. This overhaul also includes
several major fixes:
1. Prevent going back to a specific Tx column in a search
cycle if it was already explored.
2. Avoid switching to a Tx column that doesn't have any chance
if it performs perfectly to beat the current throughput we're
getting.
These issues were degrading throughput as they were causing
switching to "bad" Tx columns.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Use the 20Mhz channel width define instead of just the number
zero for legacy rates. Note that the define has the same value
so this is just a minor cleanup.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The table rs_ht_to_legacy is used to get the next legacy rate
following the last HT or VHT rate in the LQ rates table.
The mapping wasn't correct as well as didn't include entries
for MCS8/9 which led to out of bounds access. This didn't
trigger a crash but led to legacy rate entries using 1Mbps
rate.
In 5Ghz this probably caused the Tx to fail completely given
that Tx attempt would have reached the legacy entries and 1Mbps
isn't valid.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Drop code which was relevant when there were chips with
3 antennas. Setting to ANT_AB should be ok with all mvm
supported chips.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Introduce rs_rate which represents a rate. Use this structure
instead of iwl_scale_tbl_info where we're dealing with a single
rate.
This avoids allocating the big iwl_scale_tbl_info structure
on the stack in several cases like converting to ucode rate
format or from ucode rate format.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Remain in the same Tx modulation (i.e. column) for a longer
time before starting a search cycle for a better modulation.
This has been shown to give better results.
Also change the name of the timeout define to better match its
description.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Expected TPT table was updated only when switching to a new
modulation. This is wrong as toggling aggregation changes
the expected TPT signficantly.
This leads to scenarios where turning aggregation on after
being in MIMO sends us back to SISO despite a perfect success
ratio.
This occurred because the TPT of the SISO mode was being
estimated based on aggregation while the MIMO one wasn't.
Also remove an error print which isn't an error anymore
since we might be updating the expected TPT table due
to aggregation changes.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This terminates a test window of a new rate quicker in case
we've hit a bad rate and should recover better.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Enable better tracking of different decisions made
by the rate scale algorithm.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Remote peer can publish a different number of supported nss via the
operating mode notification IE or action frame. If it limits to 1
then we don't want mimo rates configured in the rate table.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
MCS9 in NSS=1 or NSS=2 isn't valid for 20Mhz so don't enable
it in case we're dealing with a 20Mhz sta. Trying to configure an
MCS9 rate with 20Mhz in the LQ rate table would lead to a FW assert.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Switch to using the new btcoex decision api regarding MIMO and stop
accessing the internal btcoex structs.
In case MIMO should be disabled it would detect this upon the next
Tx and force a search. The search will switch to SISO on a antenna A
which isn't used by BT.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
For now, the firmware doesn't really use the field, but
it should be set to zero if there's no specific request.
Setting it to the max quota doesn't make sense.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Advertise driver's support for low priority scan.
Notice that this overwrites current setting by mac80211 which depends
only on hw scan support.
This scan priority can be configured by user space application
and it affects scan continuity, low priority scan
will be more fragmented scan.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Bit 0 in the scan offloading flags asks the filter
to pass all the results (instead of filtering them,
by default), rather than the other way around (like
it is defined and used today).
Fix the flag name appropriately, and fix its user.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This allows to see the content of the NVM the driver reads.
Note that the output is in binary, and requires some
external user space tool to display the data properly.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
If we haven't loaded the D3 image yet and a failure in the suspend
process occurs, we shouldn't restart the HW, because we're still
running the D0 image.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This is just a helper function to go from the mac80211
station struct to our internal one, to later allow us
to avoid temporary 'mvmsta' variables.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
valid_rx_ant is a bitmask of available antennas and not the number
of Rx antennas. Use num_of_ant and remove duplicate definitions
in both dvm and mvm.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Eyal Shapira