Previously, tc with ets type and zero bandwidth is not accepted
by driver. This behavior does not follow the IEEE802.1qaz spec.
If there are tcs with ets type and zero bandwidth, these tcs are
assigned to the lowest priority tc_group #0. We equally distribute
100% bw of the tc_group #0 to these zero bandwidth ets tcs.
Also, the non zero bandwidth ets tcs are assigned to tc_group #1.
If there is no zero bandwidth ets tc, the non zero bandwidth ets tcs
are assigned to tc_group #0.
Fixes: cdcf11212b ("net/mlx5e: Validate BW weight values of ETS")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Added check for the maximal number of flow counters attached
to rule (FTE).
Fixes: bd5251dbf1 ('net/mlx5_core: Introduce flow steering destination of type counter')
Signed-off-by: Raed Salem <raeds@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently, FPGA capability is located in (mdev)->caps.hca_cur,
change the location to be (mdev)->caps.fpga,
since hca_cur is reserved for HCA device capabilities.
Fixes: e29341fb3a ("net/mlx5: FPGA, Add basic support for Innova")
Signed-off-by: Inbar Karmy <inbark@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Pull networking updates from David Miller:
1) Support ipv6 checksum offload in sunvnet driver, from Shannon
Nelson.
2) Move to RB-tree instead of custom AVL code in inetpeer, from Eric
Dumazet.
3) Allow generic XDP to work on virtual devices, from John Fastabend.
4) Add bpf device maps and XDP_REDIRECT, which can be used to build
arbitrary switching frameworks using XDP. From John Fastabend.
5) Remove UFO offloads from the tree, gave us little other than bugs.
6) Remove the IPSEC flow cache, from Florian Westphal.
7) Support ipv6 route offload in mlxsw driver.
8) Support VF representors in bnxt_en, from Sathya Perla.
9) Add support for forward error correction modes to ethtool, from
Vidya Sagar Ravipati.
10) Add time filter for packet scheduler action dumping, from Jamal Hadi
Salim.
11) Extend the zerocopy sendmsg() used by virtio and tap to regular
sockets via MSG_ZEROCOPY. From Willem de Bruijn.
12) Significantly rework value tracking in the BPF verifier, from Edward
Cree.
13) Add new jump instructions to eBPF, from Daniel Borkmann.
14) Rework rtnetlink plumbing so that operations can be run without
taking the RTNL semaphore. From Florian Westphal.
15) Support XDP in tap driver, from Jason Wang.
16) Add 32-bit eBPF JIT for ARM, from Shubham Bansal.
17) Add Huawei hinic ethernet driver.
18) Allow to report MD5 keys in TCP inet_diag dumps, from Ivan
Delalande.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1780 commits)
i40e: point wb_desc at the nvm_wb_desc during i40e_read_nvm_aq
i40e: avoid NVM acquire deadlock during NVM update
drivers: net: xgene: Remove return statement from void function
drivers: net: xgene: Configure tx/rx delay for ACPI
drivers: net: xgene: Read tx/rx delay for ACPI
rocker: fix kcalloc parameter order
rds: Fix non-atomic operation on shared flag variable
net: sched: don't use GFP_KERNEL under spin lock
vhost_net: correctly check tx avail during rx busy polling
net: mdio-mux: add mdio_mux parameter to mdio_mux_init()
rxrpc: Make service connection lookup always check for retry
net: stmmac: Delete dead code for MDIO registration
gianfar: Fix Tx flow control deactivation
cxgb4: Ignore MPS_TX_INT_CAUSE[Bubble] for T6
cxgb4: Fix pause frame count in t4_get_port_stats
cxgb4: fix memory leak
tun: rename generic_xdp to skb_xdp
tun: reserve extra headroom only when XDP is set
net: dsa: bcm_sf2: Configure IMP port TC2QOS mapping
net: dsa: bcm_sf2: Advertise number of egress queues
...
- Lots of hfi1 driver updates (mixed with a few qib and core updates as
well)
- rxe updates
- various mlx updates
- Set default roce type to RoCEv2
- Several larger fixes for bnxt_re that were too big for -rc
- Several larger fixes for qedr that, likewise, were too big for -rc
- Misc core changes
- Make the hns_roce driver compilable on arches other than aarch64 so we
can more easily debug build issues related to it
- Add rdma-netlink infrastructure updates
- Add automatic IRQ affinity infrastructure
- Add 32bit lid support
- Lots of misc fixes across the subsystem from random people
- Autoloading of RDMA netlink modules
- PCI pool cleanups from Romain Perier
- mlx5 driver feature additions and fixes
- Hardware tag matchine feature
- Fix sleeping in atomic when resolving roce ah
- Add experimental ioctl interface as posted to linux-api@
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJZqBDtAAoJELgmozMOVy/dNlcQAJhYNRGaNUBx0L6+8t2xwUrt
7ndP6qlMar30DJY9FjTQCzRBw0CRMWkXdJD8rYlyaHy07pjWDKG8LZtxEXu1FLdZ
oNRvQX6ZJh8Bz7db2SQFBCTF2uWGZZFqWQCrSbQwjj9xxjMDs59u/knmwHVY9dKk
egjPG4IQBDmcTeNY7h1otG2hXpx7QPIOilQW2EFN5SWAuBAazdF2JKxjjxqhnUfp
gD2pSdgsm3VSMoo0zpMa6qOP+9GcOu8J97fYFhasRYWCavPdWHyq+XNu9S/eicRd
xbv+seCYM+9jPb2dsNdjEKll7w3yyWdu7h6tSCMPYv54eN9sDDiO1w2L2ZnESMZa
JRnSfB+HXru1r4RyHOTPO8peaNhYlR1V4u8bTS5G2dffbHis9BajkWoAR/oSiUcB
AIjIIDcdJFVGfpF9KIt/pEl+adHNgESibSijzOUYkyw6RNbPqDmdd7YakPHcQhKN
clE3zQfIsPRLWsToP/nkBE0tUd3tQocRuLy7ote7hXQK+0p7TBz0a6Kkj87MvX33
8dVbUI+q6WRlEY90l71y0ZdXy/AvkxkFxAc4Y7FQZyJxhEArTaKgfa5fmpRwVxBm
yi9baoYCspHNRNv6AO4IL86ZCJqmWBuch8CBY1n2X3h8IGfKYEZUAZ+T/mnTTeUq
A4joXduz94ZD4w23leD1
=2ntC
-----END PGP SIGNATURE-----
Merge tag 'for-linus-ioctl' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma updates from Doug Ledford:
"This is a big pull request.
Of note is that I'm sending you the new ioctl API for the rdma
subsystem. We put it up on linux-api@, but didn't get much response.
The API is complex, but it solves two different problems in one go:
1) The bi-directional nature of the RDMA file write calls, which
created the security hole we had to handle (and for which the fix
is now causing problems for systems in production, we were a bit
over zealous in the fix and the ability to open a device, then
fork, then create new queue pairs on the device and use them is
broken).
2) The bloat caused by different vendors implementing extensions to
the base verbs API. Each vendor's hardware is slightly different,
and the hardware might be suitable for one extension but not
another.
By the time we add generic extensions for all the different ways
that the different hardware can offload things, the API becomes
bloated. Things like our completion structs have started to exceed
a cache line in size because of all the elements needed to support
this. That in turn shows up heavily in the performance graphs with
a noticable drop in performance on 100Gigabit links as our
completion structs go from occupying one cache line to 1+.
This API makes things like the completion structs modular in a
very similar way to netlink so that your structs can only include
the items needed for the offloads/features you are actually using
on a given queue pair. In that way we support everything, but only
use what we need, and our structs stay smaller.
The ioctl API is better explained by the posting on linux-api@ than I
can explain it here, so I'll just leave it at that.
The rest of the pull request is typical stuff.
Updates for 4.14 kernel merge window
- Lots of hfi1 driver updates (mixed with a few qib and core updates
as well)
- rxe updates
- various mlx updates
- Set default roce type to RoCEv2
- Several larger fixes for bnxt_re that were too big for -rc
- Several larger fixes for qedr that, likewise, were too big for -rc
- Misc core changes
- Make the hns_roce driver compilable on arches other than aarch64 so
we can more easily debug build issues related to it
- Add rdma-netlink infrastructure updates
- Add automatic IRQ affinity infrastructure
- Add 32bit lid support
- Lots of misc fixes across the subsystem from random people
- Autoloading of RDMA netlink modules
- PCI pool cleanups from Romain Perier
- mlx5 driver feature additions and fixes
- Hardware tag matchine feature
- Fix sleeping in atomic when resolving roce ah
- Add experimental ioctl interface as posted to linux-api@"
* tag 'for-linus-ioctl' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (328 commits)
IB/core: Expose ioctl interface through experimental Kconfig
IB/core: Assign root to all drivers
IB/core: Add completion queue (cq) object actions
IB/core: Add legacy driver's user-data
IB/core: Export ioctl enum types to user-space
IB/core: Explicitly destroy an object while keeping uobject
IB/core: Add macros for declaring methods and attributes
IB/core: Add uverbs merge trees functionality
IB/core: Add DEVICE object and root tree structure
IB/core: Declare an object instead of declaring only type attributes
IB/core: Add new ioctl interface
RDMA/vmw_pvrdma: Fix a signedness
RDMA/vmw_pvrdma: Report network header type in WC
IB/core: Add might_sleep() annotation to ib_init_ah_from_wc()
IB/cm: Fix sleeping in atomic when RoCE is used
IB/core: Add support to finalize objects in one transaction
IB/core: Add a generic way to execute an operation on a uobject
Documentation: Hardware tag matching
IB/mlx5: Support IB_SRQT_TM
net/mlx5: Add XRQ support
...
Refactor function mlx5e_lro_update_hdr() to reduce number of
branches.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add TX offloads support for GRE tunneled packets by reporting the needed
netdev features.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
MLX5_INTERFACE_STATE_SHUTDOWN is not used in the code.
Fixes: 5fc7197d3a ("net/mlx5: Add pci shutdown callback")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
There is an issue where the firmware fails during mlx5_load_one,
the health_care timer detects the issue and schedules a health_care call.
Then the mlx5_load_one detects the issue, cleans up and quits. Then
the health_care starts and calls mlx5_unload_one to clean up the resources
that no longer exist and causes kernel panic.
The root cause is that the bit MLX5_INTERFACE_STATE_DOWN is not set
after mlx5_load_one fails. The solution is removing the bit
MLX5_INTERFACE_STATE_DOWN and quit mlx5_unload_one if the
bit MLX5_INTERFACE_STATE_UP is not set. The bit MLX5_INTERFACE_STATE_DOWN
is redundant and we can use MLX5_INTERFACE_STATE_UP instead.
Fixes: 5fc7197d3a ("net/mlx5: Add pci shutdown callback")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add support to new XRQ(eXtended shared Receive Queue)
hardware object. It supports SRQ semantics with addition
of extended receive buffers topologies and offloads.
Currently supports tag matching topology and rendezvouz offload.
Signed-off-by: Artemy Kovalyov <artemyko@mellanox.com>
Reviewed-by: Yossi Itigin <yosefe@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Expose enhanced multi packet WQE capability to user space through
query_device by uhw.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Set the field to allow posting multi packet send WQEs if hardware
supports this feature. This doesn't mean the send WQEs will be for
multi packet unless the send WQE was prepared according to multi
packet send WQE format.
User space shall use flag MLX5_IB_ALLOW_MPW to check if hardware
supports MPW and allows MPW in SQ context.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Set underlay QPN as part of flow rule when it's applicable.
There is one root flow table in the NIC RX namespace and all the
underlay QPs steer the traffic to this flow table.
In order to prevent QP to get traffic which is not target to its
underlay QP, we need to set the underlay QP number as part of
the steering matching.
Note:
When multicast traffic is sent the QPN filtering is done by the firmware
as some early step. Adding the QPN match on the flow table entry is
wrong as by that time the target QPN holds the multicast address (e.g.
FF(s)) and it won't match.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch is the first step in decoupling UMR usage and
allocation from the MR cache. The only functional change
in this patch is to enables UMR for MRs created with
reg_create.
This change fixes a bug where ODP memory regions that
were not allocated from the MR cache did not have UMR
enabled.
Signed-off-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The current code stores fte_match_param in the software representation
of FTEs and FGs. fte_match_param contains a large reserved area at the
bottom of the struct. Since downstream patches are going to hash this
part, we would like to avoid doing so on a reserved part.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
mlx5_core_wq is no longer being used and should be removed
from the code.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The PCI pool API is deprecated. This commit replaces the PCI pool old
API by the appropriate function with the DMA pool API.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Reviewed-by: Peter Senna Tschudin <peter.senna@collabora.com>
Acked-by: Doug Ledford <dledford@redhat.com>
Tested-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add outbound_pci_buffer_overflow to ethtool output for monitoring the
number of packets that were dropped due to lack of PCIe buffers on
receive path from NIC port toward the host(s).
This counter is valid only in case that tx_overflow_buffer_pkt is
supported in MCAM enhanced features.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add capability bit in PCAM register and counters to PPCNT register.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add capability bit in MCAM register and counters to MPCNT register.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Conflicts:
drivers/infiniband/hw/mlx5/main.c - Both add new code
include/rdma/ib_verbs.h - Both add new code
Signed-off-by: Doug Ledford <dledford@redhat.com>
The UDP offload conflict is dealt with by simply taking what is
in net-next where we have removed all of the UFO handling code
entirely.
The TCP conflict was a case of local variables in a function
being removed from both net and net-next.
In netvsc we had an assignment right next to where a missing
set of u64 stats sync object inits were added.
Signed-off-by: David S. Miller <davem@davemloft.net>
generic api takes care of spreading affinity similar to
what mlx5 open coded (and even handles better asymmetric
configurations). Ask the generic API to spread affinity
for us, and feed him pre_vectors that do not participate
in affinity settings (which is an improvement to what we
had before).
The affinity assignments should match what mlx5 tried to
do earlier but now we do not set affinity to async, cmd
and pages dedicated vectors.
Also, remove mlx5e_get_cpu and introduce mlx5e_get_node
(used for allocation purposes) and mlx5_get_vector_affinity
(for indirection table construction) as they provide the needed
information. Luckily, we have generic helpers to get cpumask
and node given a irq vector. mlx5_get_vector_affinity will
be used by mlx5_ib in a subsequent patch.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Now that we have a generic code to allocate an array
of irq vectors and even correctly spread their affinity,
correctly handle cpu hotplug events and more, were much
better off using it.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Doug Ledford <dledford@redhat.com>
- small set of miscellanous fixes
- a reasonably sizable set of IPoIB fixes that deal with multiple long
standing issues
-----BEGIN PGP SIGNATURE-----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=2fQS
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma fixes from Doug Ledford:
"Third set of -rc fixes for 4.13 cycle
- small set of miscellanous fixes
- a reasonably sizable set of IPoIB fixes that deal with multiple
long standing issues"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
IB/hns: checking for IS_ERR() instead of NULL
RDMA/mlx5: Fix existence check for extended address vector
IB/uverbs: Fix device cleanup
RDMA/uverbs: Prevent leak of reserved field
IB/core: Fix race condition in resolving IP to MAC
IB/ipoib: Notify on modify QP failure only when relevant
Revert "IB/core: Allow QP state transition from reset to error"
IB/ipoib: Remove double pointer assigning
IB/ipoib: Clean error paths in add port
IB/ipoib: Add get statistics support to SRIOV VF
IB/ipoib: Add multicast packets statistics
IB/ipoib: Set IPOIB_NEIGH_TBL_FLUSH after flushed completion initialization
IB/ipoib: Prevent setting negative values to max_nonsrq_conn_qp
IB/ipoib: Make sure no in-flight joins while leaving that mcast
IB/ipoib: Use cancel_delayed_work_sync when needed
IB/ipoib: Fix race between light events and interface restart
Read new NIC capability field which represnts 16 MSBs of the max flow
counters number supported (max_flow_counter_31_16).
Backward compatibility with older firmware is preserved, the modified
driver reads max_flow_counter_31_16 as 0 from the older firmware and
uses up to 64K counters.
Changed flow counter id from 16 bits to 32 bits. Backward compatibility
with older firmware is preserved as we kept the 16 LSBs of the counter
id in place and added 16 MSBs from reserved field.
Changed the background bulk reading of flow counters to work in chunks
of at most 32K counters, to make sure we don't attempt to allocate very
large buffers.
Signed-off-by: Rabie Loulou <rabiel@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The counter list hardware structure doesn't contain a clear and
num_of_counters fields, remove them.
These wrong fields were never used by the driver hence no other driver
changes.
Fixes: a351a1b03b ("net/mlx5: Introduce bulk reading of flow counters")
Signed-off-by: Rabie Loulou <rabiel@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When mlx5_ib registers itself to mlx5_core as an interface, it will
call mlx5_add_device which will call mlx5_ib interface add callback,
in case the latter successfully returns, only then mlx5_core will add
it to the interface list and async events will be forwarded to mlx5_ib.
Between mlx5_ib interface add callback and mlx5_core adding the mlx5_ib
interface to its devices list, arriving mlx5_core events can be missed
by the new mlx5_ib registering interface.
In other words:
thread 1: mlx5_ib: mlx5_register_interface(dev)
thread 1: mlx5_core: mlx5_add_device(dev)
thread 1: mlx5_core: ctx = dev->add => (mlx5_ib)->mlx5_ib_add
thread 2: mlx5_core_event: **new event arrives, forward to dev_list
thread 1: mlx5_core: add_ctx_to_dev_list(ctx)
/* previous event was missed by the new interface.*/
It is ok to miss events before dev->add (mlx5_ib)->mlx5_ib_add_device
but not after.
We fix this race by accumulating the events that come between the
ib_register_device (inside mlx5_add_device->(dev->add)) till the adding
to the list completes and fire them to the new registering interface
after that.
Fixes: f1ee87fe55 ("net/mlx5: Organize device list API in one place")
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Multi-Physical Function Switch (MPFs) is required for when multi-PF
configuration is enabled to allow passing user configured unicast MAC
addresses to the requesting PF.
Before this patch eswitch.c used to manage the HW MPFS l2 table,
E-Switch always (regardless of sriov) enabled vport(0) (NIC PF) vport's
contexts update on unicast mac address list changes, to populate the PF's
MPFS L2 table accordingly.
In downstream patch we would like to allow compiling the driver without
E-Switch functionalities, for that we move MPFS l2 table logic out
of eswitch.c into its own file, and provide Kconfig flag (MLX5_MPFS) to
allow compiling out MPFS for those who don't want Multi-PF support.
NIC PF netdevice will now directly update MPFS l2 table via the new MPFS
API. VF netdevice has no access to MPFS L2 table, so E-Switch will remain
responsible of updating its MPFS l2 table on behalf of its VFs.
Due to this change we also don't require enabling vport(0) (PF vport)
unicast mac changes events anymore, for when SRIOV is not enabled.
Which means E-Switch is now activated only on SRIOV activation, and not
required otherwise.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Cc: Jes Sorensen <jsorensen@fb.com>
Cc: kernel-team@fb.com
The extended address vector is the highest bit in be32 variable,
but it was compared with the lowest. This patch fixes the endianness
of that check and removes already declared define.
Fixes: 17d2f88f92 ("IB/mlx5: Add ODP atomics support")
Reviewed-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In order to mark relevant fields while setting the MTPPS register
add field select. Otherwise it can cause a misconfiguration in
firmware.
Fixes: ee7f12205a ('net/mlx5e: Implement 1PPS support')
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This patch adds below requester and responder side error counters,
which will be exposed by hardware counters interface and are supported
as part of query Q counters command extension.
+---------------------------+-------------------------------------+
| Name | Description |
|---------------------------+-------------------------------------|
|resp_local_length_error | Number of times responder detected |
| | local length errors |
|---------------------------+-------------------------------------|
|resp_cqe_error | Number of CQEs completed with error |
| | at responder |
|---------------------------+-------------------------------------|
|req_cqe_error | Number of CQEs completed with error |
| | at requester |
|---------------------------+-------------------------------------|
|req_remote_invalid_request | Number of times requester detected |
| | remote invalid request error |
|---------------------------+-------------------------------------|
|req_remote_access_error | Number of times requester detected |
| | remote access error |
|---------------------------+-------------------------------------|
|resp_remote_access_error | Number of times responder detected |
| | remote access error |
|---------------------------+-------------------------------------|
|resp_cqe_flush_error | Number of CQEs completed with |
| | flushed with error at responder |
|---------------------------+-------------------------------------|
|req_cqe_flush_error | Number of CQEs completed with |
| | flushed with error at requester |
+---------------------------+-------------------------------------+
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The extended address vector is the highest bit in be32 variable,
but it was compared with the lowest. This patch fixes the endianness
of that check and removes already declared define.
Fixes: 17d2f88f92 ("IB/mlx5: Add ODP atomics support")
Reviewed-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Report 'ipoib_enhanced_offloads' capabilities from
the core layer, it will be used in the next patch from this series.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
RQs that were configured for "delay drop" will prevent packet drops
when their WQEs are depleted.
Marking an RQ to be drop-less is done by setting delay_drop_en in RQ
context using CREATE_RQ command.
Since this feature is globally activated/deactivated by using the
SET_DELAY_DROP command on all the marked RQs, we activated/deactivated
it according to the number of RQs with 'delay_drop' enabled.
When timeout is expired, then the feature is deactivated. Therefore
the driver handles the delay drop timeout event and reactivate it.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When delay drop timeout is expired, the firmware raises
general notification event of DELAY_DROP_TIMEOUT subtype.
In addition the feature is disable so the driver have to
reactivate the timeout.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add support to SET_DELAY_DROP command.
This command will be used in downstream patches for delay packet drop.
The timeout value should be indicated by delay_drop_timeout field.
Packet processing will be delayed till timeout value passed or until
more WQEs are posted.
Setting this value to 0 disables the feature.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When a user sets port_guid, node_guid or policy of an IB virtual
function, save this information in "struct mlx5_vf_context".
This information will be restored later when pci_resume is called.
To make sure this works, one can use aer-inject to generate PCI
errors on mlx5 devices and verify if relevant fields are restored
after PCI resume.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch adds debug control parameters for congestion control which
can be read or written through debugfs. They are for reaction point and
notification point nodes.
These control parameters are as below:
+------------------------------+-----------------------------------------+
| Name | Description |
|------------------------------+-----------------------------------------|
|rp_clamp_tgt_rate | When set target rate is updated to |
| | current rate |
|------------------------------+-----------------------------------------|
|rp_clamp_tgt_rate_ati | When set update target rate based on |
| | timer as well |
|------------------------------+-----------------------------------------|
|rp_time_reset | time between rate increase if no |
| | CNP is received unit in usec |
|------------------------------+-----------------------------------------|
|rp_byte_reset | Number of bytes between rate inease if |
| | no CNP is received |
|------------------------------+-----------------------------------------|
|rp_threshold | Threshold for reaction point rate |
| | control |
|------------------------------+-----------------------------------------|
|rp_ai_rate | Rate for target rate, unit in Mbps |
|------------------------------+-----------------------------------------|
|rp_hai_rate | Rate for hyper increase state |
| | unit in Mbps |
|------------------------------+-----------------------------------------|
|rp_min_dec_fac | Minimum factor by which the current |
| | transmit rate can be changed when |
| | processing a CNP, unit is percerntage |
|------------------------------+-----------------------------------------|
|rp_min_rate | Minimum value for rate limit, |
| | unit in Mbps |
|------------------------------+-----------------------------------------|
|rp_rate_to_set_on_first_cnp | Rate that is set when first CNP is |
| | received, unit is Mbps |
|------------------------------+-----------------------------------------|
|rp_dce_tcp_g | Used to calculate alpha |
|------------------------------+-----------------------------------------|
|rp_dce_tcp_rtt | Time between updates of alpha value, |
| | unit is usec |
|------------------------------+-----------------------------------------|
|rp_rate_reduce_monitor_period | Minimum time between consecutive rate |
| | reductions |
|------------------------------+-----------------------------------------|
|rp_initial_alpha_value | Initial value of alpha |
|------------------------------+-----------------------------------------|
|rp_gd | When CNP is received, flow rate is |
| | reduced based on gd, rp_gd is given as |
| | log2(rp_gd) |
|------------------------------+-----------------------------------------|
|np_cnp_dscp | dscp code point for generated cnp |
|------------------------------+-----------------------------------------|
|np_cnp_prio_mode | 802.1p priority for generated cnp |
|------------------------------+-----------------------------------------|
|np_cnp_prio | cnp priority mode |
+------------------------------+-----------------------------------------+
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add support for raw ethernet local loopback firmware command.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Some overlapping changes in the mlx5 driver.
A merge conflict resolution posted by Stephen Rothwell was used as a
guide.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Innova IPSec ESP crypto offload configuration paths.
Detect Innova IPSec device and set the NETIF_F_HW_ESP flag.
Configure Security Associations using the API introduced in a previous
patch.
Add Software-parser hardware descriptor layout
Software-Parser (swp) is a hardware feature in ConnectX which allows the
host software to specify protocol header offsets in the TX path, thus
overriding the hardware parser.
This is useful for protocols that the ASIC may not be able to parse on
its own.
Note that due to inline metadata, XDP is not supported in Innova IPSec.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Yossi Kuperman <yossiku@mellanox.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add routines for manipulating the hardware IPSec SA database (SADB).
In Innova IPSec, a Security Association (SA) is added or deleted
via a command message over the SBU connection.
The HW then sends a response message over the same connection.
Add implementation for Innova IPSec (FPGA-based) hardware.
These routines will be used by the IPSec offload support in a later patch
However they may also be used by others such as RDMA and RoCE IPSec.
mlx5/accel is a middle acceleration layer to allow mlx5e and other ULPs
to work directly with mlx5_core rather than Innova FPGA or other mlx5
acceleration providers.
In this patchset we add Innova IPSec support and mlx5/accel delegates
IPSec offloads to Innova routines.
In the future, when IPSec/TLS or any other acceleration gets integrated
into ConnectX chip, mlx5/accel layer will provide the integrated
acceleration, rather than the Innova one.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add interface to initialize and interact with Innova FPGA SBU
connections.
A client driver may use these functions to set up a high-speed DMA
connection with its SBU hardware logic, and send/receive messages
over this connection.
A later patch in this patchset will make use of these functions for
Innova IPSec offload in mlx5 Ethernet driver.
Add commands to retrieve Innova FPGA SBU capabilities, and to
read/write Innova FPGA configuration space registers and memory,
over internal I2C.
At high level, the FPGA configuration space is divided such:
0x00000000 - 0x007fffff is reserved for the SBU
0x00800000 - 0xffffffff is reserved for the Shell
0x400000000 - ... is DDR memory
A later patchset will add support for accessing FPGA CrSpace and memory
over a high-speed connection. This is the reason for the ACCESS_TYPE
enumeration, which currently only supports I2C.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The Innova FPGA includes shell hardware and Sandbox-Unit (SBU) hardware.
The shell hardware is handled by mlx5_core itself, while the SBU is
handled by a client driver.
Reset the SBU to a well-known initial state when initializing a new
device, and set the FPGA to bypass mode when uninitializing a device.
This allows the client driver to assume that its device has been
reset when a new device is detected.
During SBU reset, the FPGA is put into SBU-bypass mode. In this mode
packets do not pass through the SBU, so it cannot affect the network
data stream at all.
A factory-image does not have an SBU, so skip these flows.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The FPGA QP is a high-bandwidth communication channel between the host
CPU and the FPGA device. It allows performing DMA operations between
host memory and the FPGA logic via the ConnectX chip.
Add ConnectX FW commands which create and manipulate FPGA QPs.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Previously, only mlx5_ib enabled RoCE on the port, but FPGA needs it as
well.
Add support for counting number of enables, so that FPGA and IB can work
in parallel and independently.
Program the HW to enable RoCE on the first enable call, and program to
disable RoCE on the last disable call.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Huy Nguyen