The STMPE MFD is only used with device tree configured systems (and STMPE
MFD core depends on OF), so force the configuration to come from device
tree only.
Tested-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Require that device tree be used with STMPE (all platforms use this)
and enforce OF_GPIO, then delete the platform data.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The STMPE keypad controller is only used with device tree configured
systems, so force the configuration to come from device tree only, and now
actually get the rows and cols from the device tree too.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds the register offsets for pull up/down for the STMPE
1601, 1801 and 24xx expanders. This is used to bias GPIO lines
and keypad lines.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The only platform using the STMPE expander now boots from
device tree using all-dynamic GPIO and IRQ number assignments, so
remove the mechanism to pass this from the device tree entirely.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The STMPE has VCC and VIO supply lines, and sometimes (as on
Ux500) this comes from a software-controlled regulator. Make
it possible to supply the STMPE with power from these
regulators.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Provides support for 1801 variant of stmpe gpio port expanders.
This chip has 18 gpios configurable as GPI, GPO, keypad matrix,
special key or dedicated key function.
Note that special/dedicated key function is not supported yet.
Signed-off-by: Jean-Nicolas Graux <jean-nicolas.graux@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Since the very first patch, stmpe core driver is using irq_invert_polarity as
part of platform data. But, nobody is actually using it in kernel till now.
Also, this is not something part of hardware specs, but is included to cater
some board mistakes or quirks.
So, better get rid of it. This is earlier discussed here:
https://lkml.org/lkml/2012/11/27/636
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The STMPE driver is yet another IRQ controller which requires its
own IRQ domain. So, we provide it with one.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Since it's not like we will re-arrange the keys at run-time, it
seems proper to allow the keymap data to be const. This solves
a compilation warning in ux500.
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=onDl
-----END PGP SIGNATURE-----
Merge tag 'mfd_3.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFD changes from Samuel Ortiz:
- 4 new drivers: Freescale i.MX on-chip Anatop, Ricoh's RC5T583 and
TI's TPS65090 and TPS65217.
- New variants support (8420, 8520 ab9540), cleanups and bug fixes for
the abx500 and db8500 ST-E chipsets.
- Some minor fixes and update for the wm8994 from Mark.
- The beginning of a long term TWL cleanup effort coming from the TI
folks.
- Various fixes and cleanups for the s5m, TPS659xx, pm860x, and MAX8997
drivers.
Fix up trivial conflicts due to duplicate patches and header file
cleanups (<linux/device.h> removal etc).
* tag 'mfd_3.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (97 commits)
gpio/twl: Add DT support to gpio-twl4030 driver
gpio/twl: Allocate irq_desc dynamically for SPARSE_IRQ support
mfd: Detach twl6040 from the pmic mfd driver
mfd: Replace twl-* pr_ macros by the dev_ equivalent and do various cleanups
mfd: Micro-optimization on twl4030 IRQ handler
mfd: Make twl4030 SIH SPARSE_IRQ capable
mfd: Move twl-core IRQ allocation into twl[4030|6030]-irq files
mfd: Remove references already defineid in header file from twl-core
mfd: Remove unneeded header from twl-core
mfd: Make twl-core not depend on pdata->irq_base/end
ARM: OMAP2+: board-omap4-*: Do not use anymore TWL6030_IRQ_BASE in board files
mfd: Return twl6030_mmc_card_detect IRQ for board setup
Revert "mfd: Add platform data for MAX8997 haptic driver"
mfd: Add support for TPS65090
mfd: Add some da9052-i2c section annotations
mfd: Build rtc5t583 only if I2C config is selected to y.
mfd: Add anatop mfd driver
mfd: Fix compilation error in tps65910.h
mfd: Add 8420 variant to db8500-prcmu
mfd: Add 8520 PRCMU variant to db8500-prcmu
...
The <linux/device.h> header includes a lot of stuff, and
it in turn gets a lot of use just for the basic "struct device"
which appears so often.
Clean up the users as follows:
1) For those headers only needing "struct device" as a pointer
in fcn args, replace the include with exactly that.
2) For headers not really using anything from device.h, simply
delete the include altogether.
3) For headers relying on getting device.h implicitly before
being included themselves, now explicitly include device.h
4) For files in which doing #1 or #2 uncovers an implicit
dependency on some other header, fix by explicitly adding
the required header(s).
Any C files that were implicitly relying on device.h to be
present have already been dealt with in advance.
Total removals from #1 and #2: 51. Total additions coming
from #3: 9. Total other implicit dependencies from #4: 7.
As of 3.3-rc1, there were 110, so a net removal of 42 gives
about a 38% reduction in device.h presence in include/*
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Adds support for boards which have an STMPE device without the
interrupt pin connected.
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Chris Blair <chris.blair@stericsson.com>
Tested-by: Michel Jaouen <michel.jaouen@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
STMPE801 is a GPIO expander. Registers for 801 are much different from other
variants. This patch adds support for STMPE801 in stmpe mfd driver.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@st.com>
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
STMPE610 is very much like STMPE811, except the number of gpio pins, which is 8
in 811 and 6 in 610. This patch adds support for variant 610. STMPE610 will
share most of the code with STMPE811.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Few STMPE controller can have register interface over SPI or I2C. Current
implementation only supports I2C and all code is present in a single file
stmpe.c. It would be better to separate out I2C interface specific code from
controller specific code. Later SPI specific code can be added in a separate
file.
This patch separates out I2C and controller specific code into separate files,
making stmpe.c independent of I2C.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
On many boards, stmpe is present as an separate device (not as part of SoC).
Here gpio lines are mostly used for getting interrupts. This patch adds in
support to handle irq over gpio pin.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Generating kerneldoc for STMPE result in warnings, so fix this by
adding missing documentation.
Signed-off-by: Om Prakash <omprakash.pal@stericsson.com>
Reviewed-by: Rabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
GPIOs on these controller are multi-functional. If you decided to use
some of them e.g. as input channels for the ADC, you surely don't want
those pins to be reassigned as simple GPIOs (which may be triggered even
from userspace via 'export'). Same for the touchscreen controller pins.
Since knowledge about the hardware is needed to decide which GPIOs to
reserve, let this bitmask be inside platform_data and provide some
defines to assist potential users.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Rabin Vincent <rabin.vincent@stericsson.com>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Some STMPE devices support entering sleep mode automatically on a
specified timeout of inactivity on the I2C bus with the host system.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Sundar R Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add support for the STMPE family of I/O Expanders from
STMicroelectronics. These devices include upto 24 gpios and a varying
selection of blocks, including PWM, keypad, and touchscreen controllers.
This patch adds the MFD core.
[l.fu@pengutronix.de: fix stmpe811 enable hook]
[l.fu@pengutronix.de: add touchscreen platform data]
Acked-by: Luotao Fu <l.fu@pengutronix.de>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Dmitry Torokhov