The virtual driver implements fasync and ioctl support, but it is not used
and unneeded due to its constraints via the Bluetooth core layer. So too
just make the driver simpler, remove support for both of them.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The BKL push down added some BKL into the open callback of the virtual
driver. The driver is really simple and need no such locking and so just
remove it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The virtual driver still uses a home grown way of waiting for events and
so just replace it with wait_event_interruptible. And while at it remove
the useless access_ok() checks.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Allowing to specify a specific misc minor number for the virtual driver
is pretty much useless and nobody is using this feature. So just remove
it and use MISC_DYNAMIC_MINOR all the time.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Submitting the bulk URBs for ACL data transfers only on demand has no
real benefit compared to just submit them when a Bluetooth device gets
opened. So when submitting the interrupt URBs for HCI events, just
submit the bulk URBs, too.
This solves a problem with some Bluetooth USB dongles that has been
reported over the last few month. These devices require that the bulk
URBs are actually present. These devices are really broken, but there
is nothing we can do about it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This eliminates a sparse warning that symbol 'stat' shadows an earlier one.
Signed-off-by: Andre Haupt <andre@bitwigglers.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
With the introduction of CONFIG_DYNAMIC_PRINTK_DEBUG it is possible to
allow debugging without having to recompile the kernel. This patch turns
all BT_DBG() calls into pr_debug() to support dynamic debug messages.
As a side effect all CONFIG_BT_*_DEBUG statements are now removed and
some broken debug entries have been fixed.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch allows the Asus WL-BTD202 dongle to be used with a mono
headset without having to specify "options btusb force_scofix=1".
Based on a patch from Guillaume Bedot <littletux@zarb.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Bluetooth subsystem was not using the HCI Reset command when doing
device initialization. The Bluetooth 1.0b specification was ambiguous
on how the device firmware was suppose to handle it. Almost every device
was triggering a transport reset at the same time. In case of USB this
ended up in disconnects from the bus.
All modern Bluetooth dongles handle this perfectly fine and a lot of
them actually require that HCI Reset is sent. If not then they are
either stuck in their HID Proxy mode or their internal structures for
inquiry and paging are not correctly setup.
To handle old and new devices smoothly the Bluetooth subsystem contains
a quirk to force the HCI Reset on initialization. However maintaining
such a quirk becomes more and more complicated. This patch turns the
logic around and lets the old devices disable the HCI Reset command.
The only device where the HCI_QUIRK_NO_RESET is still needed are the
original Digianswer devices and dongles with an early CSR firmware.
CSR reported that they fixed this for version 12 firmware. The last
official release of version 11 firmware is build ID 115. The first
version 12 candidate was build ID 117.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The old hci_usb driver has been fully replaced with the new btusb driver
and all major distributions switched to the new driver now. This removes
it since it should not be used at all anymore.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Following the pattern from hci_*.c, turn off BT_DBG messages unless
they have been requested via HCI_UART_DEBUG
Signed-off-by: Nick Pelly <npelly@google.com>
Acked-by: Brian Swetland <swetland@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since size, addr, fcs, and tmp are unsigned, it would seem better to use
simple_strtoul that simple_strtol.
A simplified version of the semantic patch that makes this change is as
follows: (http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r2@
long e;
position p;
@@
e = simple_strtol@p(...)
@@
position p != r2.p;
type T;
T e;
@@
e =
- simple_strtol@p
+ simple_strtoul
(...)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch fixes accumulating of the header in case packet was requeued
in the error path.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
During suspend it is important that all URBs are cancelled and then on
resume re-submitted. This gives initial suspend/resume support.
Based on initial work from Oliver Neukum <oneukum@suse.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
With the addition of usb_unlink_anchored_urbs() it is possible to fully
control the bulk URBs from the notify callback. There is no need to
schedule work and so only do this for the ISOC URBs.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The URB submission routines need more fine grained control for the
mem_flags used by kmalloc(), usb_alloc_urb() and usb_submit_urb() to
better support different caller situations. Add a mem_flags parameter
and give the caller full control.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Inspired by Sergio Luis' similar patches, I finally found
a case which is trivial enough that spatch won't choke
on it.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6:
fdomain_cs: Sort out modules with duplicate description
pcmcia: Whine harder about use of EXCLUSIVE
pcmcia: IRQ_TYPE_EXCLUSIVE is long obsoleted
Switch more drivers to dynamic sharing after checking their IRQ handlers
use dev_id and are robust
Signed-off-by: Alan Cox <alan@redhat.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Move the set up on ldisc change into the ldisc
Move the INQ/OUTQ cases into the driver not in shared ioctl code where it
gives bogus answers for other ldisc values
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The new A-Link Bluetooth dongle is another one based on the BCM2046 chip
from Broadcom and it also needs to send HCI_Reset before it becomes fully
operational. Without the quirk it will show a lot of I/O errors.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Targus and Belkin have come out with new Bluetooth 2.1 capable dongles
using the latest BCM2046 chip from Broadcom. Both of them are so called
HID proxy dongles and they need to send HCI_Reset before they become
fully operational.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The transfer buffer of an URB will be automatically freed when using
the URB_FREE_BUFFER transfer_flag. So the extra calls to kfree() will
cause a double free.
Reported-by: Justin Mattock <justinmattock@gmail.com>
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
smp_mb is enough for ordering memory operations among processors,and mb is
more expensive than smp_mb for UP machine, so replace it with smp_mb().
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The USB transport specification for Bluetooth splits the ACL and SCO
handling into two separate interfaces. In Linux it possible to probe
and disconnect these interfaces independently. So make sure that both
interfaces are tightly bound together.
This fixes the suspend regression that some people have expierenced.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The btusb driver contains two typos that result in some buggy behavior,
but the impact is not immediately visible.
During initialization the submitting of interrupt URBs might fail and
then make sure to remove the correct flag and not one of the hci_dev
flags.
When closing down the interface make sure to kill the anchor for the
ISOC URBs and not kill the interrupt URBs twice.
Also cancel any scheduled work when closing down the interface.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The newer MacBooks contain a Broadcom based Bluetooth chip and to make
this work properly, HCI_Reset must be send first. If HCI_Reset is not
used then a lot of I/O errors show up and its triggers packets from
non-existent ACL links.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Instead of using own error or success codes, the PCMCIA code should rely on
the generic return values. Therefore, replace all occurrences of CS_SUCCESS
with 0.
CC: netdev@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
By passing the current Vcc setting to the pcmcia_config_loop callback
function, we can remove pcmcia_get_configuration_info() calls from many
drivers.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Many drivers use the default CIS entry within their pcmcia_config_loop()
callback function. Therefore, factor the default CIS entry handling out.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Almost all drivers set p_dev->conf.ConfigIndex to cfg->index in
the pcmcia_config_loop() callback function. Therefore, factor it out.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Use the config loop helper in bluetooth pcmcia drivers.
CC: Marcel Holtmann <marcel@holtmann.org>
CC: linux-bluetooth@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The Bluetooth entries for the MAINTAINERS file are a little bit too
much. Consolidate them into two entries. One for Bluetooth drivers and
another one for the Bluetooth subsystem.
Also the MODULE_AUTHOR should indicate the current maintainer of the
module and actually not the original author. Fix all Bluetooth modules
to provide current maintainer information.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The new generic driver for Bluetooth USB devices was missing proper
SCO support. The driver now claims the second interface for these USB
devices to allow the flow of SCO packets. It also handles switching
of the alternate setting and re-submission of isochronous URBs.
The btusb driver is now a full replacement for hci_usb and thus the
experimental tag has been removed and this driver is promoted as
preferred one.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This implements all the quirk handling from the hci_usb driver to the
new btusb driver.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This removes the unnecessary ignore parameter, which is useless. There
are alternate methods of kicking a driver off an USB device.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Preface: The "Broadcom" device is on unreleased hardware, so I can't
disclose the actual model.
When the Dell 370 and 410 BT adapters are put into BT radio mode, they
need to be prepared like many other Broadcom adapters.
Also, add quirk Broadcom 2046 devices with HCI_RESET. Reference for this
bug: https://launchpad.net/bugs/249448
Signed-off-by: Michael Frey <michael.frey@canonical.com>
Signed-off-by: Mario Limonciello <Mario_Limonciello@Dell.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Ben Collins <ben.collins@canonical.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (1232 commits)
iucv: Fix bad merging.
net_sched: Add size table for qdiscs
net_sched: Add accessor function for packet length for qdiscs
net_sched: Add qdisc_enqueue wrapper
highmem: Export totalhigh_pages.
ipv6 mcast: Omit redundant address family checks in ip6_mc_source().
net: Use standard structures for generic socket address structures.
ipv6 netns: Make several "global" sysctl variables namespace aware.
netns: Use net_eq() to compare net-namespaces for optimization.
ipv6: remove unused macros from net/ipv6.h
ipv6: remove unused parameter from ip6_ra_control
tcp: fix kernel panic with listening_get_next
tcp: Remove redundant checks when setting eff_sacks
tcp: options clean up
tcp: Fix MD5 signatures for non-linear skbs
sctp: Update sctp global memory limit allocations.
sctp: remove unnecessary byteshifting, calculate directly in big-endian
sctp: Allow only 1 listening socket with SO_REUSEADDR
sctp: Do not leak memory on multiple listen() calls
sctp: Support ipv6only AF_INET6 sockets.
...
Move the line disciplines towards a conventional ->ops arrangement. For
the moment the actual 'tty_ldisc' struct in the tty is kept as part of
the tty struct but this can then be changed if it turns out that when it
all settles down we want to refcount ldiscs separately to the tty.
Pull the ldisc code out of /proc and put it with our ldisc code.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix bluetooth hci_bcsp Kconfig to avoid build errors:
drivers/built-in.o: In function `bcsp_prepare_pkt':
hci_bcsp.c:(.text+0x7e9ac): undefined reference to `bitrev16'
drivers/built-in.o: In function `bcsp_recv':
hci_bcsp.c:(.text+0x7f276): undefined reference to `bitrev16'
hci_bcsp.c:(.text+0x7f293): undefined reference to `bitrev16'
make[1]: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Ackey-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-2.6.27' of git://git.infradead.org/users/dwmw2/firmware-2.6: (64 commits)
firmware: convert sb16_csp driver to use firmware loader exclusively
dsp56k: use request_firmware
edgeport-ti: use request_firmware()
edgeport: use request_firmware()
vicam: use request_firmware()
dabusb: use request_firmware()
cpia2: use request_firmware()
ip2: use request_firmware()
firmware: convert Ambassador ATM driver to request_firmware()
whiteheat: use request_firmware()
ti_usb_3410_5052: use request_firmware()
emi62: use request_firmware()
emi26: use request_firmware()
keyspan_pda: use request_firmware()
keyspan: use request_firmware()
ttusb-budget: use request_firmware()
kaweth: use request_firmware()
smctr: use request_firmware()
firmware: convert ymfpci driver to use firmware loader exclusively
firmware: convert maestro3 driver to use firmware loader exclusively
...
Fix up trivial conflicts with BKL removal in drivers/char/dsp56k.c and
drivers/char/ip2/ip2main.c manually.
Use bitrev16 from lib/bitrev.c.
Use the get_unaligned_be16 to get the crc from the packet, create a
small helper function for this.
Fix a shadowed variable sparse warning:
drivers/bluetooth/hci_bcsp.c:218:26: warning: symbol 'hdr' shadows an earlier one
drivers/bluetooth/hci_bcsp.c:187:5: originally declared here
[akpm@linux-foundation.org: select CONFIG_BITREVERSE, noted by akinobu.mita@gmail.com]
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If someone tries to _urb_unlink while _urb_queue_head is running, he'll see
_urb->queue == NULL and fail to do any locking. Prevent that from happening
by strategically placed barriers.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Something Arjan suggested which allows us to clean up the code nicely
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Operations are now a shared const function block as with most other Linux
objects
- Introduce wrappers for some optional functions to get consistent behaviour
- Wrap put_char which used to be patched by the tty layer
- Document which functions are needed/optional
- Make put_char report success/fail
- Cache the driver->ops pointer in the tty as tty->ops
- Remove various surplus lock calls we no longer need
- Remove proc_write method as noted by Alexey Dobriyan
- Introduce some missing sanity checks where certain driver/ldisc
combinations would oops as they didn't check needed methods were present
[akpm@linux-foundation.org: fix fs/compat_ioctl.c build]
[akpm@linux-foundation.org: fix isicom]
[akpm@linux-foundation.org: fix arch/ia64/hp/sim/simserial.c build]
[akpm@linux-foundation.org: fix kgdb]
Signed-off-by: Alan Cox <alan@redhat.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
_urb_free is an alias for kfree... making code longer & harder to
read. Remove it.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
hci_usb: do not initialize static variables to 0.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (47 commits)
[SCTP]: Fix local_addr deletions during list traversals.
net: fix build with CONFIG_NET=n
[TCP]: Prevent sending past receiver window with TSO (at last skb)
rt2x00: Add new D-Link USB ID
rt2x00: never disable multicast because it disables broadcast too
libertas: fix the 'compare command with itself' properly
drivers/net/Kconfig: fix whitespace for GELIC_WIRELESS entry
[NETFILTER]: nf_queue: don't return error when unregistering a non-existant handler
[NETFILTER]: nfnetlink_queue: fix EPERM when binding/unbinding and instance 0 exists
[NETFILTER]: nfnetlink_log: fix EPERM when binding/unbinding and instance 0 exists
[NETFILTER]: nf_conntrack: replace horrible hack with ksize()
[NETFILTER]: nf_conntrack: add \n to "expectation table full" message
[NETFILTER]: xt_time: fix failure to match on Sundays
[NETFILTER]: nfnetlink_log: fix computation of netlink skb size
[NETFILTER]: nfnetlink_queue: fix computation of allocated size for netlink skb.
[NETFILTER]: nfnetlink: fix ifdef in nfnetlink_compat.h
[NET]: include <linux/types.h> into linux/ethtool.h for __u* typedef
[NET]: Make /proc/net a symlink on /proc/self/net (v3)
RxRPC: fix rxrpc_recvmsg()'s returning of msg_name
net/enc28j60: oops fix
...
This adds another Broadcom BCM2045 based device to the blacklist, with
these settings the micro dongle works on my system.
Signed-off-by: Karsten Keil <kkeil@suse.de>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
From: SDiZ <sdiz@sdiz.net>
Fix the CONWISE Technology based adapters with buggy SCO support issue
(bugzilla #9027)
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arjan:
With the help of kerneloops.org I've spotted a nice little interaction
between the TTY layer and the bluetooth code, however the tty layer is not
something I'm all too familiar with so I rather ask than brute-force fix the
code incorrectly.
The raw details are at:
http://www.kerneloops.org/search.php?search=uart_flush_buffer
What happens is that, on closing the bluetooth tty, the tty layer goes
into the release_dev() function, which first does a bunch of stuff, then
sets the file->private_data to NULL, does some more stuff and then calls the
ldisc close function. Which in this case, is hci_uart_tty_close().
Now, hci_uart_tty_close() calls hci_uart_close() which clears some
internal bit, and then calls hci_uart_flush()... which calls back to the
tty layers' uart_flush_buffer() function. (in drivers/bluetooth/hci_tty.c
around line 194) Which then WARN_ON()'s because that's not allowed/supposed
to be called this late in the shutdown of the port....
Should the bluetooth driver even call this flush function at all??
David:
This seems to be what happens: Hci_uart_close() flushes using
hci_uart_flush(). Subsequently, in hci_dev_do_close(), (one step in
hci_unregister_dev()), hci_uart_flush() is called again. The comment in
uart_flush_buffer(), relating to the WARN_ON(), indicates you can't flush
after the port is closed; which sounds reasonable. I think hci_uart_close()
should set hdev->flush to NULL before returning. Hci_dev_do_close() does
check for this. The code path is rather involved and I'm not entirely clear
of all steps, but I think that's what should be done.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove kio_addr_t, and replace it with unsigned int. No known architecture
needs more than 32 bits for IO addresses and ports and having a separate type
for it is just messy.
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This device is recognized as bluetooth, but still not works.
Signed-off-by: Andy Shevchenko <andy@smile.org.ua>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a double-free spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixea a memleak spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the (rare) event of simultaneous mutual wake up requests,
do send the chip an explicit wake-up ack. This is required
for Texas Instruments's BRF6350 chip.
Signed-off-by: Ohad Ben-Cohen <ohad@bencohen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new generic driver for Bluetooth USB devices. This
driver is still experimental at this point, but it is cleaner and
easier to maintain than the current Bluetooth USB driver. It is a
much better starting point for power management improvements.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a generic driver for Bluetooth SDIO devices. It
supports Type-A and Type-B devices.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Our info structure and info->hdev is always passed to the IRQ handler,
so we don't have to worry about these checks in every interrupt.
Leave a BUG_ON() just to help unwary programmers, but these could
probably be removed as well.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add support for Texas Instruments' HCI Low Level (HCILL) Bluetooth
protocol, which is a power management extension to H4. The HCILL is
widely used by TI's BRF63xx Bluetooth chips.
Signed-off-by: Ohad Ben-Cohen <ohad@bencohen.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
With the new support for USB anchors the driver can become more
simpler and also cleaner. This patch switches to the usage of USB
anchors for all URBs.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Bluetooth HCI commands are divided into logical OGF groups for
easier identification of their purposes. While this still makes sense
for the written specification, its makes the code only more complex
and harder to read. So instead of using separate OGF and OCF values
to identify the commands, use a common 16-bit opcode that combines
both values. As a side effect this also reduces the complexity of
OGF and OCF calculations during command header parsing.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
With the support for hci_recv_fragment() the call to increase the
stat.byte_rx counter got accidentally removed. This patch fixes it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Remove the llseek method given that the open method already calls
nonseekable_open().
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch modifies the HCI USB driver to use the new helper function
for reassembling HCI data packets and events.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In case of Broadcom based Bluetooth devices, it is safe to always
send HCI_Reset as first command. This gives the advantage that
all HID Proxy versions will automatically work and don't need any
additional quirks anymore.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
A trivial fix to (what looks like) an unintentional fall-through in the
HCI line discipline.
Signed-off-by: Ohad Ben-Cohen <ohad@bencohen.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Normally a serial Bluetooth device is opened, TIOSETD'ed to N_HCI line
discipline, HCIUARTSETPROTO'ed and finally closed. In case the device
fails to HCIUARTSETPROTO, closing it produces a NULL pointer dereference.
Signed-off-by: Ohad Ben-Cohen <ohad@bencohen.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Adding HCIUARTGETDEVICE makes it possible to get the HCI device number
that is attached to a given serial device. This is required during the
initialization process of some Bluetooth chips.
Signed-off-by: Ohad Ben-Cohen <ohad@bencohen.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The SCO buffer size values for Bluetooth chips from Broadcom are wrong
and the USB Bluetooth driver has to set a quirk to correct these SCO
buffer size values.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds the vendor and product id of the Targus ACB10US
dongle and sets a flag to send HCI_Reset as the first command.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org
To clearly state the intent of copying from linear sk_buffs, _offset being a
overly long variant but interesting for the sake of saving some bytes.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
For consistency with other skb data accessors, reducing the number of direct
accesses to skb->data.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Some Bluetooth drivers need one or more binary firmware images. Export
these image names via the MODULE_FIRMWARE tag.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
After Al Viro (finally) succeeded in removing the sched.h #include in module.h
recently, it makes sense again to remove other superfluous sched.h includes.
There are quite a lot of files which include it but don't actually need
anything defined in there. Presumably these includes were once needed for
macros that used to live in sched.h, but moved to other header files in the
course of cleaning it up.
To ease the pain, this time I did not fiddle with any header files and only
removed #includes from .c-files, which tend to cause less trouble.
Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha,
arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig,
allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all
configs in arch/arm/configs on arm. I also checked that no new warnings were
introduced by the patch (actually, some warnings are removed that were emitted
by unnecessarily included header files).
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Many struct file_operations in the kernel can be "const". Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data. In addition it'll catch accidental writes at compile time to
these shared resources.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The SCO buffer size values on Dell laptops with a Bluetooth chip from
Broadcom are wrong. The USB Bluetooth driver has to set a quirk to
correct the SCO buffer size values.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The SCO buffer size values on HP laptops with a Bluetooth chip from
Broadcom are wrong. The USB Bluetooth driver has to set a quirk to
correct the SCO buffer size values.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The ThinkPad R60E uses a Broadcom based Bluetooth chip and even this
version needs the quirk to correct the SCO buffer size values.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Conflicts:
drivers/pcmcia/ds.c
Fix up merge failures with Linus's head and fix new compile failures.
Signed-Off-By: David Howells <dhowells@redhat.com>
struct pcmcia_device *p_dev->conf.ConfigBase and .Present are set in almost
all PCMICA driver right at the beginning, using the same calls but slightly
different implementations. Unfiy this in the PCMCIA core.
Includes a small bugfix ("drivers/net/pcmcia/xirc2ps_cs.c: remove unused
label") from and Signed-off-by Adrian Bunk <bunk@stusta.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The device id for the Nokia DTL-4 PCMCIA card was missing. This patch
adds it back to the list of supported devices.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds the vendor and product id of the ANYCOM Bluetooth
USB-200 and USB-250 dongles and sets a flag to send HCI_Reset as
the first command.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org
The bcm203x firmware loading driver uses a timer to trigger the URB
submission. It is better to use a work queue instead.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
This patch cleans up the Bluetooth HCI UART driver a bit.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds the vendor and product id of the Canycon CN-BTU1
dongle and sets a flag to send HCI_Reset as the first command.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch assigns the next free HCI device identifier to Bluetooth
devices based on the SDIO interface.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch is an attempt to cleanup the drivers source code to make all
Bluetooth drivers look more unique.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Broadcom dongles with HID proxy support actually support SCO over
HCI if the SCO buffer size values are corrected. So instead of disabling
the SCO support, mark this dongle with the quirk for the Bluetooth core
to correct the wrong buffer size values.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch disables the ISOC transfers for another broken RTX Telecom
based USB dongle. Starting the USB ISOC transfers only ends in a burst
of error messages for invalid SCO packets on connection handle 0.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Belkin F8T012 and F8T013 devices are both based on a Bluetooth chip
from Broadcom and their SCO buffer size values are wrong. The Bluetooth
core should correct these values.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The SCO buffer size values on IBM/Lenovo ThinkPad laptops with a
Bluetooth chip from Broadcom are wrong. The USB Bluetooth driver
has to set a quirk to correct the SCO buffer size values.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Use release_firmware() to free requested resources.
According to Documentation/firmware_class/README the request_firmware()
call should be followed by a release_firmware(). Some drivers do not
however free the firmware previously allocated with request_firmware().
This patch tries to fix this by making sure that release_firmware() is used
as expected.
Signed-off-by: Magnus Damm <magnus@valinux.co.jp>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds a generic Bluetooth platform device that can be used
as parent device by virtual and serial devices.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch introduces a quirk that allows the drivers to tell the host
to correct the SCO buffer size values.
Signed-off-by: Olivier Galibert <galibert@pobox.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch implements the suspend/resume methods for the HCI USB
driver by killing all outstanding URBs on suspend, and re-issuing
them on resume.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Frontline sniffer device looks like a normal H:2 Bluetooth device,
but it is not and so mark it as raw mode device.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There's a problem in drivers/bluetooth/dtl1_cs.c::dtl1_hci_send_frame()
If bt_skb_alloc() returns NULL, then skb_reserve(s, NSHL); will cause a
NULL pointer deref - ouch. If we can't allocate the resources we require
we need to tell the caller by returning -ENOMEM.
Found by the coverity checker as bug #409
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Instead of the two status values struct pcmcia_device->p_state and state,
use descriptive bitfields. Most value-checking in drivers was invalid, as
the core now only calls the ->remove() (a.k.a. detach) function in case the
attachement _and_ configuration was successful.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Most of the driver initialization isn't done in the .probe function, but in
the internal _config() functions. Make them return a value, so that .probe
can properly report whether the probing of the device succeeded or not.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
dev_link_t * and client_handle_t both mean struct pcmcai_device * by now.
Therefore, remove all such indirections.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Embed dev_link_t into struct pcmcia_device(), as they basically address the
same entity. The actual contents of dev_link_t will be cleaned up step by step.
This patch includes a bugfix from and signed-off-by Andrew Morton.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
As we do not allow setting Vcc in the pcmcia core, and Vpp1 and
Vpp2 can only be set to the same value, a lot of code can be
streamlined.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
In all but one case, the suspend and resume functions of PCMCIA drivers
contain mostly of calls to pcmcia_release_configuration() and
pcmcia_request_configuration(). Therefore, move this code out of the
drivers and into the core.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
pcmcia_disable_device(struct pcmcia_device *p_dev) performs the necessary
cleanups upon device or driver removal: it calls the appropriate
pcmcia_release_* functions, and can replace (most) of the current drivers'
_release() functions.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Before the PCMCIA subsystem was fully integrated into the device and
driver model, the BT3C driver had to workaround this when loading the
firmware. This workaround is broken and makes the driver oops when
loading the firmware. This patch removes this workaround and uses now
the provided device structure from the PCMCIA subsystem.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Remove the "inline" keyword from a bunch of big functions in the kernel with
the goal of shrinking it by 30kb to 40kb
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The API and code have been through various bits of initial review by
serial driver people but they definitely need to live somewhere for a
while so the unconverted drivers can get knocked into shape, existing
drivers that have been updated can be better tuned and bugs whacked out.
This replaces the tty flip buffers with kmalloc objects in rings. In the
normal situation for an IRQ driven serial port at typical speeds the
behaviour is pretty much the same, two buffers end up allocated and the
kernel cycles between them as before.
When there are delays or at high speed we now behave far better as the
buffer pool can grow a bit rather than lose characters. This also means
that we can operate at higher speeds reliably.
For drivers that receive characters in blocks (DMA based, USB and
especially virtualisation) the layer allows a lot of driver specific
code that works around the tty layer with private secondary queues to be
removed. The IBM folks need this sort of layer, the smart serial port
people do, the virtualisers do (because a virtualised tty typically
operates at infinite speed rather than emulating 9600 baud).
Finally many drivers had invalid and unsafe attempts to avoid buffer
overflows by directly invoking tty methods extracted out of the innards
of work queue structs. These are no longer needed and all go away. That
fixes various random hangs with serial ports on overflow.
The other change in here is to optimise the receive_room path that is
used by some callers. It turns out that only one ldisc uses receive room
except asa constant and it updates it far far less than the value is
read. We thus make it a variable not a function call.
I expect the code to contain bugs due to the size alone but I'll be
watching and squashing them and feeding out new patches as it goes.
Because the buffers now dynamically expand you should only run out of
buffering when the kernel runs out of memory for real. That means a lot of
the horrible hacks high performance drivers used to do just aren't needed any
more.
Description:
tty_insert_flip_char is an old API and continues to work as before, as does
tty_flip_buffer_push() [this is why many drivers dont need modification]. It
does now also return the number of chars inserted
There are also
tty_buffer_request_room(tty, len)
which asks for a buffer block of the length requested and returns the space
found. This improves efficiency with hardware that knows how much to
transfer.
and tty_insert_flip_string_flags(tty, str, flags, len)
to insert a string of characters and flags
For a smart interface the usual code is
len = tty_request_buffer_room(tty, amount_hardware_says);
tty_insert_flip_string(tty, buffer_from_card, len);
More description!
At the moment tty buffers are attached directly to the tty. This is causing a
lot of the problems related to tty layer locking, also problems at high speed
and also with bursty data (such as occurs in virtualised environments)
I'm working on ripping out the flip buffers and replacing them with a pool of
dynamically allocated buffers. This allows both for old style "byte I/O"
devices and also helps virtualisation and smart devices where large blocks of
data suddenely materialise and need storing.
So far so good. Lots of drivers reference tty->flip.*. Several of them also
call directly and unsafely into function pointers it provides. This will all
break. Most drivers can use tty_insert_flip_char which can be kept as an API
but others need more.
At the moment I've added the following interfaces, if people think more will
be needed now is a good time to say
int tty_buffer_request_room(tty, size)
Try and ensure at least size bytes are available, returns actual room (may be
zero). At the moment it just uses the flipbuf space but that will change.
Repeated calls without characters being added are not cumulative. (ie if you
call it with 1, 1, 1, and then 4 you'll have four characters of space. The
other functions will also try and grow buffers in future but this will be a
more efficient way when you know block sizes.
int tty_insert_flip_char(tty, ch, flag)
As before insert a character if there is room. Now returns 1 for success, 0
for failure.
int tty_insert_flip_string(tty, str, len)
Insert a block of non error characters. Returns the number inserted.
int tty_prepare_flip_string(tty, strptr, len)
Adjust the buffer to allow len characters to be added. Returns a buffer
pointer in strptr and the length available. This allows for hardware that
needs to use functions like insl or mencpy_fromio.
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: John Hawkes <hawkes@sgi.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add some PCMCIA device IDs for the microdrive found in the Sharp Zaurus
and a different revision of the Socket CF+ Bluetooth card.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Unify the EVENT_CARD_INSERTION and "attach" callbacks to one unified
probe() callback. As all in-kernel drivers are changed to this new
callback, there will be no temporary backwards-compatibility. Inside a
probe() function, each driver _must_ set struct pcmcia_device
*p_dev->instance and instance->handle correctly.
With these patches, the basic driver interface for 16-bit PCMCIA drivers
now has the classic four callbacks known also from other buses:
int (*probe) (struct pcmcia_device *dev);
void (*remove) (struct pcmcia_device *dev);
int (*suspend) (struct pcmcia_device *dev);
int (*resume) (struct pcmcia_device *dev);
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The linked list of devices managed by each PCMCIA driver is, in very most
cases, unused. Therefore, remove it from many drivers.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Unify the "detach" and REMOVAL_EVENT handlers to one "remove" function.
Old functionality is preserved, for the moment.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Move the suspend and resume methods out of the event handler, and into
special functions. Also use these functions for pre- and post-reset, as
almost all drivers already do, and the remaining ones can easily be
converted.
Bugfix to include/pcmcia/ds.c
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
This patch adds the endian annotations to the Bluetooth core.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patchs adds the module parameter ignore_dga to the HCI USB driver
which makes it possible to prevent this driver from being loaded by
some buggy Digianswer devices.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a BPA 100/105 device contains more then one interface then ignore the
additional interfaces, because they are unused.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch contains the big cleanup of the HCI UART driver. The uneeded
header files are removed and their structure declarations are moved into
the protocol implementations.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
- added typedef unsigned int __nocast gfp_t;
- replaced __nocast uses for gfp flags with gfp_t - it gives exactly
the same warnings as far as sparse is concerned, doesn't change
generated code (from gcc point of view we replaced unsigned int with
typedef) and documents what's going on far better.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds the module parameters ignore_csr and ignore_sniffer
to the HCI USB driver. This allows an easier use of CSR ROM chips
that need an additional initialization routine and the Frontline
sniffers.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch moves the usage of packet type into the SKB control
buffer. After this patch it is now possible to shrink the sk_buff
structure and redefine its pkt_type.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the sparse warnings "implicit cast to nocast type"
for the priority or gfp_mask parameters of the memory allocations.
Signed-off-by: Victor Fusco <victor@cetuc.puc-rio.br>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch cleans up the virtual HCI driver. It also adds support for
the dynamic minor device number allocation.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the "list" member of struct sk_buff, as it is entirely
redundant. All SKB list removal callers know which list the
SKB is on, so storing this in sk_buff does nothing other than
taking up some space.
Two tricky bits were SCTP, which I took care of, and two ATM
drivers which Francois Romieu <romieu@fr.zoreil.com> fixed
up.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
This patch removes the unused bt_dump() function and it also removes
its BT_DMP macro. It also unexports the hci_dev_get(), hci_send_cmd()
and hci_si_event() functions.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There's no need to check for NULL before calling kfree() on a pointer.
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Kensington Bluetooth USB adapter is based on a Broadcom chip
with the HID proxy support. To initialize these kind of devices
correctly it is necessary to send HCI_Reset as the first command.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This is part of the grand scheme to eliminate the qlen
member of skb_queue_head, and subsequently remove the
'list' member of sk_buff.
Most users of skb_queue_len() want to know if the queue is
empty or not, and that's trivially done with skb_queue_empty()
which doesn't use the skb_queue_head->qlen member and instead
uses the queue list emptyness as the test.
Signed-off-by: David S. Miller <davem@davemloft.net>
As a follow-up, remove the inclusion of pcmcia/version.h in many files.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move the "event handler" to struct pcmcia_driver -- the unified event handler
will disappear really soon, but switching it to struct pcmcia_driver in the
meantime allows for better "step-by-step" patches.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Marcel Holtmann