and prepare and enable them at the same time. This also comes with devm support
so that drivers can make a single call to get and prepare and enable the clk
and have that all undone when their driver is removed. Many folks have
requested this feature over the years, but we've had disagreements about how to
implement it and if it was worthwhile to encourage drivers to use such an API.
Now it's here, so let's see how it goes. I hope that by introducing this API we
can identify drivers that would benefit from further consolidation of clk API
usage, possibly by moving such logic to the bus layer and out of drivers
altogether.
Outside of that major API update, we have the usual collection of driver
updates. A few new SoCs are supported, mostly Qualcomm and Renesas this time
around. Then we have the long tail of non-critical fixes and minor feature
additions to various clk drivers. And finally more clk provider migration to
struct clk_parent_data, reducing boot times in the process.
Core:
- devm helpers for clk_get() + clk_prepare() and clk_enable()
New Drivers:
- Support for the camera clock controller in Qualcomm SM8450 and
the display and gpu clock controllers in Qualcomm SM8350
- Add support for the Renesas RZ/Five SoC
Updates:
- Various fixes, new clocks and USB GDSCs are introduced for Qualcomm IPQ8074
- Fixes to Qualcomm MSM8939 for issues introduced by inheriting the MSM8916
GCC driver
- Support for a new type of voteable GDSCs used by Qualcomm SC8280XP PCIe
GDSCs
- Qualcomm SC8280XP pipe clocks transitioned to the new phy-mux implementation
- Qualcomm MSM8996 GCC, RPM clock driver and some clocks in MSM8994 GCC are
migrated to use clk_parent_data
- Corrected the topology for Titan (camera) GDSCs on Qualcomm SDM845 and
SM8250
- Qualcomm MSM8916 gains more possible frequencies for its GP clocks.
- The GCC and tsens handling on Qualcomm MSM8960 is reworked to mimic the
design in IPQ8074 to allow the GCC driver to probe earlier.
- The regulator based mmcx supply for Qualcomm dispcc and videocc is dropped,
as the only upstream target that adapted this interface was transitioned
several kernel versions ago
- Qualcomm GDSCs found to be enabled at boot will now reflect in the enable
count of the supply, as was done with the regulator supplies previously
- Correct adc1, nic_media and edma1's parents for NXP i.MX93
- rdiv, mfd values, the return rate in recalc_rate and add more frequencies in
the table for fracn-gppll on i.MX
- Remove Allwinner workaround logic/compatible in fixed factor code
- MediaTek clk driver cleanups
- Add reset support to more MediaTek clk drivers
- deduplicate Allwinner ccu_clks arrays
- Allwinner H6 GPU DFS support
- Adjust Allwinner Kconfig to limit choice
- Fix initconst confusion on Renesas R-Car Gen4
- Add GPT/POEG (PWM) clocks and resets on Renesas RZ/G2L
- Add PFC and WDT clocks and resets on Renesas RZ/V2M
- Add thermal, SDHI, Z (CPU core), PCIe, and HSCIF (serial) clocks on
Renesas R-Car S4-8
-----BEGIN PGP SIGNATURE-----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=jUh+
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"The clk core gains a new set of APIs that allow drivers to both
acquire clks and prepare and enable them at the same time. This also
comes with devm support so that drivers can make a single call to get
and prepare and enable the clk and have that all undone when their
driver is removed.
Many folks have requested this feature over the years, but we've had
disagreements about how to implement it and if it was worthwhile to
encourage drivers to use such an API.
Now it's here, so let's see how it goes.
I hope that by introducing this API we can identify drivers that would
benefit from further consolidation of clk API usage, possibly by
moving such logic to the bus layer and out of drivers altogether.
Outside of that major API update, we have the usual collection of
driver updates. A few new SoCs are supported, mostly Qualcomm and
Renesas this time around. Then we have the long tail of non-critical
fixes and minor feature additions to various clk drivers.
And finally more clk provider migration to struct clk_parent_data,
reducing boot times in the process.
Summary:
Core:
- devm helpers for clk_get() + clk_prepare() and clk_enable()
New Drivers:
- Support for the camera clock controller in Qualcomm SM8450 and the
display and gpu clock controllers in Qualcomm SM8350
- Add support for the Renesas RZ/Five SoC
Updates:
- Various fixes, new clocks and USB GDSCs are introduced for Qualcomm
IPQ8074
- Fixes to Qualcomm MSM8939 for issues introduced by inheriting the
MSM8916 GCC driver
- Support for a new type of voteable GDSCs used by Qualcomm SC8280XP
PCIe GDSCs
- Qualcomm SC8280XP pipe clocks transitioned to the new phy-mux
implementation
- Qualcomm MSM8996 GCC, RPM clock driver and some clocks in MSM8994
GCC are migrated to use clk_parent_data
- Corrected the topology for Titan (camera) GDSCs on Qualcomm SDM845
and SM8250
- Qualcomm MSM8916 gains more possible frequencies for its GP clocks.
- The GCC and tsens handling on Qualcomm MSM8960 is reworked to mimic
the design in IPQ8074 to allow the GCC driver to probe earlier.
- The regulator based mmcx supply for Qualcomm dispcc and videocc is
dropped, as the only upstream target that adapted this interface
was transitioned several kernel versions ago
- Qualcomm GDSCs found to be enabled at boot will now reflect in the
enable count of the supply, as was done with the regulator supplies
previously
- Correct adc1, nic_media and edma1's parents for NXP i.MX93
- rdiv, mfd values, the return rate in recalc_rate and add more
frequencies in the table for fracn-gppll on i.MX
- Remove Allwinner workaround logic/compatible in fixed factor code
- MediaTek clk driver cleanups
- Add reset support to more MediaTek clk drivers
- deduplicate Allwinner ccu_clks arrays
- Allwinner H6 GPU DFS support
- Adjust Allwinner Kconfig to limit choice
- Fix initconst confusion on Renesas R-Car Gen4
- Add GPT/POEG (PWM) clocks and resets on Renesas RZ/G2L
- Add PFC and WDT clocks and resets on Renesas RZ/V2M
- Add thermal, SDHI, Z (CPU core), PCIe, and HSCIF (serial) clocks on
Renesas R-Car S4-8"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (124 commits)
clk: fixed-factor: Introduce *clk_hw_register_fixed_factor_parent_hw()
clk: mux: Introduce devm_clk_hw_register_mux_parent_hws()
clk: divider: Introduce devm_clk_hw_register_divider_parent_hw()
clk: qcom: gcc-msm8994: use parent_hws for gpll0/4
clk: qcom: clk-rpm: convert to parent_data API
dt-bindings: clock: fix wrong clock documentation for qcom,rpmcc
clk: qcom: gcc-msm8939: Add missing USB HS system clock frequencies
clk: qcom: gcc-msm8939: Add missing MDSS MDP clock frequencies
clk: qcom: gcc-msm8939: Add missing CAMSS CPP clock frequencies
clk: qcom: gcc-msm8939: Fix venus0_vcodec0_clk frequency definitions
clk: qcom: gcc-msm8939: Add missing CAMSS CCI bus clock
clk: qcom: gcc-msm8939: Fix weird field spacing in ftbl_gcc_camss_cci_clk
clk: qcom: gdsc: Bump parent usage count when GDSC is found enabled
clk: qcom: Drop mmcx gdsc supply for dispcc and videocc
clk: qcom: fix build error initializer element is not constant
clk: sprd: Add dt-bindings include file for UMS512
dt-bindings: clk: sprd: Add bindings for ums512 clock controller
clk: sunxi-ng: sun50i: h6: Modify GPU clock configuration to support DFS
dt-bindings: clock: qcom,gcc-msm8996: add more GCC clock sources
clk: qcom: add support for SM8350 DISPCC
...
This adds initial support for two SoC families that have been under
review for a while. In both cases, the origonal idea was to have a
minimally functional version, but we ended up leaving out the clk drivers
that are still under review and will be merged through the corresponding
subsystem tree.
The Nuvoton NPCM8xx is a 64-bit Baseboard Management Controller and
based on the 32-bit NPCM7xx family but is now getting added to
arch/arm64 as well.
Sunplus SP7021, also known as Plus1, is a general-purpose
System-in-Package design based on the 32-bit Cortex-A7 SoC
on the main chip, plus an I/O chip and memory in the same
-----BEGIN PGP SIGNATURE-----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=7Id+
-----END PGP SIGNATURE-----
Merge tag 'arm-newsoc-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM new SoC support from Arnd Bergmann:
"This adds initial support for two SoC families that have been under
review for a while. In both cases, the origonal idea was to have a
minimally functional version, but we ended up leaving out the clk
drivers that are still under review and will be merged through the
corresponding subsystem tree.
The Nuvoton NPCM8xx is a 64-bit Baseboard Management Controller and
based on the 32-bit NPCM7xx family but is now getting added to
arch/arm64 as well.
Sunplus SP7021, also known as Plus1, is a general-purpose
System-in-Package design based on the 32-bit Cortex-A7 SoC on the main
chip, plus an I/O chip and memory in the same"
* tag 'arm-newsoc-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (25 commits)
MAINTAINERS: rectify entry for ARM/NUVOTON NPCM ARCHITECTURE
arm64: defconfig: Add Nuvoton NPCM family support
arm64: dts: nuvoton: Add initial NPCM845 EVB device tree
arm64: dts: nuvoton: Add initial NPCM8XX device tree
arm64: npcm: Add support for Nuvoton NPCM8XX BMC SoC
dt-bindings: arm: npcm: Add nuvoton,npcm845 GCR compatible string
dt-bindings: arm: npcm: Add nuvoton,npcm845 compatible string
dt-bindings: arm: npcm: Add maintainer
reset: npcm: Add NPCM8XX support
dt-bindings: reset: npcm: Add support for NPCM8XX
reset: npcm: using syscon instead of device data
ARM: dts: nuvoton: add reset syscon property
dt-bindings: reset: npcm: add GCR syscon property
dt-binding: clk: npcm845: Add binding for Nuvoton NPCM8XX Clock
dt-bindings: watchdog: npcm: Add npcm845 compatible string
dt-bindings: timer: npcm: Add npcm845 compatible string
ARM: dts: Add Sunplus SP7021-Demo-V3 board device tree
ARM: sp7021_defconfig: Add Sunplus SP7021 defconfig
ARM: sunplus: Add initial support for Sunplus SP7021 SoC
irqchip: Add Sunplus SP7021 interrupt controller driver
...
Add clock, memory controller, powergate and reset dt-binding headers
for Host1x and VIC on Tegra234.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the clocks and resets used by the MGBE Ethernet hardware found on
Tegra234 SoCs.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bhadram Varka <vbhadram@nvidia.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
To support reset of infra_ao, add the index of infra_ao reset of
thermal/svs for MT8186.
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220523093346.28493-18-rex-bc.chen@mediatek.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
To support reset of infra_ao, add the index of infra_ao reset of
thermal/svs/pcei for MT8192 and thermal/svs for MT8195.
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
[Nícolas: Test for MT8192]
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20220523093346.28493-14-rex-bc.chen@mediatek.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add reset and IOMMU header for Tegra234 GPCDMA
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
framework that simplifies a runtime PM call. Otherwise the majority of the diff
falls to a few SoC drivers: Qualcomm, STM32 and MediaTek. Those SoCs gain some
new hardware support and what comes along with that is quite a few lines of
data and some clk_ops code. Beyond the new hardware support we have the usual
pile of driver updates that add missing clks on already supported SoCs or fix
up problems like bad clk tree descriptions. It's nice to see that more drivers
are moving to clk_hw based APIs too.
New Drivers:
- Add STM32MP13 RCC driver (Reset Clock Controller)
- MediaTek MT8186 SoC clk support
- Airoha EN7523 SoC system clocks
- Clock driver for exynosautov9 SoC
- Renesas R-Car V4H and RZ/V2M SoCs
- Renesas RZ/G2UL SoC
- LPASS clk driver for Qualcomm sc7280 SoC
- GCC clk driver for Qualcomm SC8280XP SoC
Updates:
- SDCC uses floor clk ops on Qualcomm MSM8976
- Add modem reset and fix RPM clks on Qualcomm MSM8976
- Add the two missing CLKOUT clocks for U8500/DB8500 SoC
- Mark some clks critical on Ingenic X1000
- Convert ux500 to clk_hw
- Move MediaTek driver to clk_hw provider APIs
- Use i2c driver probe_new to avoid id scans
- Convert a number of Rockchip dt bindings to YAML
- Mark hclk_vo critical on Rockchip rk3568
- Use pm_runtime_resume_and_get to fix pm_runtime_get_sync() usage
- Various cleanups like memory allocation error checks and plugged leaks
- Allwinner H6 RTC clock support
- Allwinner H616 32 kHz clock support
- Add the Universal Flash Storage clock on Renesas R-Car S4-8
- Add I2C, SSIF-2 (sound), USB, CANFD, OSTM (timer), WDT, SPI Multi
I/O Bus, RSPI, TSU (thermal), and ADC clocks and resets on Renesas RZ/G2UL
- Add display clock support on Renesas RZ/G2L
- Add RPC (QSPI/HyperFlash) clocks on Renesas R-Car E3 and D3
- Add 27 MHz phy PLL ref clock on i.MX
- Add mcore_booted module parameter to tell kernel M core has already booted
for i.MX
- Remove snvs clock on i.MX because it was for secure world only
- Add dt bindings for i.MX8MN GPT
- Add DISP2 pixel clock for i.MX8MP
- Add clkout1/2 for i.MX8MP
- Fix parent clock of ubs_root_clk for i.MX8MP
- Implement better RCG parking on Qualcomm SoCs using the shared RCG clk ops
- Kerneldoc fixes
- Switch Tegra BPMP to determine_rate clk op
- Add a pointer to dt schema for generic clock bindings
-----BEGIN PGP SIGNATURE-----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=7lBA
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"Mainly driver updates this time around.
There's a single patch to the core clk framework that simplifies a
runtime PM call. Otherwise the majority of the diff falls to a few SoC
drivers: Qualcomm, STM32 and MediaTek. Those SoCs gain some new
hardware support and what comes along with that is quite a few lines
of data and some clk_ops code.
Beyond the new hardware support we have the usual pile of driver
updates that add missing clks on already supported SoCs or fix up
problems like bad clk tree descriptions. It's nice to see that more
drivers are moving to clk_hw based APIs too.
New Drivers:
- Add STM32MP13 RCC driver (Reset Clock Controller)
- MediaTek MT8186 SoC clk support
- Airoha EN7523 SoC system clocks
- Clock driver for exynosautov9 SoC
- Renesas R-Car V4H and RZ/V2M SoCs
- Renesas RZ/G2UL SoC
- LPASS clk driver for Qualcomm sc7280 SoC
- GCC clk driver for Qualcomm SC8280XP SoC
Updates:
- SDCC uses floor clk ops on Qualcomm MSM8976
- Add modem reset and fix RPM clks on Qualcomm MSM8976
- Add the two missing CLKOUT clocks for U8500/DB8500 SoC
- Mark some clks critical on Ingenic X1000
- Convert ux500 to clk_hw
- Move MediaTek driver to clk_hw provider APIs
- Use i2c driver probe_new to avoid id scans
- Convert a number of Rockchip dt bindings to YAML
- Mark hclk_vo critical on Rockchip rk3568
- Use pm_runtime_resume_and_get to fix pm_runtime_get_sync() usage
- Various cleanups like memory allocation error checks and plugged
leaks
- Allwinner H6 RTC clock support
- Allwinner H616 32 kHz clock support
- Add the Universal Flash Storage clock on Renesas R-Car S4-8
- Add I2C, SSIF-2 (sound), USB, CANFD, OSTM (timer), WDT, SPI Multi
I/O Bus, RSPI, TSU (thermal), and ADC clocks and resets on Renesas
RZ/G2UL
- Add display clock support on Renesas RZ/G2L
- Add RPC (QSPI/HyperFlash) clocks on Renesas R-Car E3 and D3
- Add 27 MHz phy PLL ref clock on i.MX
- Add mcore_booted module parameter to tell kernel M core has already
booted for i.MX
- Remove snvs clock on i.MX because it was for secure world only
- Add dt bindings for i.MX8MN GPT
- Add DISP2 pixel clock for i.MX8MP
- Add clkout1/2 for i.MX8MP
- Fix parent clock of ubs_root_clk for i.MX8MP
- Implement better RCG parking on Qualcomm SoCs using the shared RCG
clk ops
- Kerneldoc fixes
- Switch Tegra BPMP to determine_rate clk op
- Add a pointer to dt schema for generic clock bindings"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (168 commits)
Revert "clk: qcom: regmap-mux: add pipe clk implementation"
Revert "clk: qcom: gcc-sc7280: use new clk_regmap_mux_safe_ops for PCIe pipe clocks"
Revert "clk: qcom: gcc-sm8450: use new clk_regmap_mux_safe_ops for PCIe pipe clocks"
clk: bcm: rpi: Use correct order for the parameters of devm_kcalloc()
clk: stm32mp13: add safe mux management
clk: stm32mp13: add multi mux function
clk: stm32mp13: add all STM32MP13 kernel clocks
clk: stm32mp13: add all STM32MP13 peripheral clocks
clk: stm32mp13: manage secured clocks
clk: stm32mp13: add composite clock
clk: stm32mp13: add stm32 divider clock
clk: stm32mp13: add stm32_gate management
clk: stm32mp13: add stm32_mux clock management
clk: stm32: Introduce STM32MP13 RCC drivers (Reset Clock Controller)
dt-bindings: rcc: stm32: add new compatible for STM32MP13 SoC
clk: ti: clkctrl: replace usage of found with dedicated list iterator variable
clk: ti: composite: Prefer kcalloc over open coded arithmetic
dt-bindings: clock: exynosautov9: correct count of NR_CLK
clk: mediatek: mt8173: Switch to clk_hw provider APIs
clk: mediatek: Switch to clk_hw provider APIs
...
There are minor updates to SoC specific drivers for chips by Rockchip,
Samsung, NVIDIA, TI, NXP, i.MX, Qualcomm, and Broadcom. Noteworthy
driver changes include:
- Several conversions of DT bindings to yaml format.
- Renesas adds driver support for R-Car V4H, RZ/V2M and RZ/G2UL SoCs.
- Qualcomm adds a bus driver for the SSC (Snapdragon Sensor Core),
and support for more chips in the RPMh power domains and the soc-id.
- NXP has a new driver for the HDMI blk-ctrl on i.MX8MP.
- Apple M1 gains support for the on-chip NVMe controller, making it
possible to finally use the internal disks. This also includes SoC
drivers for their RTKit IPC and for the SART DMA address filter.
For other subsystems that merge their drivers through the SoC tree,
we have
- Firmware drivers for the ARM firmware stack including TEE, OP-TEE,
SCMI and FF-A get a number of smaller updates and cleanups. OP-TEE
now has a cache for firmware argument structures as an optimization,
and SCMI now supports the 3.1 version of the specification.
- Reset controller updates to Amlogic, ASpeed, Renesas and ACPI drivers
- Memory controller updates for Tegra, and a few updates for other
platforms.
-----BEGIN PGP SIGNATURE-----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=XoLF
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM driver updates from Arnd Bergmann:
"There are minor updates to SoC specific drivers for chips by Rockchip,
Samsung, NVIDIA, TI, NXP, i.MX, Qualcomm, and Broadcom.
Noteworthy driver changes include:
- Several conversions of DT bindings to yaml format.
- Renesas adds driver support for R-Car V4H, RZ/V2M and RZ/G2UL SoCs.
- Qualcomm adds a bus driver for the SSC (Snapdragon Sensor Core),
and support for more chips in the RPMh power domains and the
soc-id.
- NXP has a new driver for the HDMI blk-ctrl on i.MX8MP.
- Apple M1 gains support for the on-chip NVMe controller, making it
possible to finally use the internal disks. This also includes SoC
drivers for their RTKit IPC and for the SART DMA address filter.
For other subsystems that merge their drivers through the SoC tree, we
have
- Firmware drivers for the ARM firmware stack including TEE, OP-TEE,
SCMI and FF-A get a number of smaller updates and cleanups. OP-TEE
now has a cache for firmware argument structures as an
optimization, and SCMI now supports the 3.1 version of the
specification.
- Reset controller updates to Amlogic, ASpeed, Renesas and ACPI
drivers
- Memory controller updates for Tegra, and a few updates for other
platforms"
* tag 'arm-drivers-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (159 commits)
memory: tegra: Add MC error logging on Tegra186 onward
memory: tegra: Add memory controller channels support
memory: tegra: Add APE memory clients for Tegra234
memory: tegra: Add Tegra234 support
nvme-apple: fix sparse endianess warnings
soc/tegra: pmc: Document core domain fields
soc: qcom: pdr: use static for servreg_* variables
soc: imx: fix semicolon.cocci warnings
soc: renesas: R-Car V3U is R-Car Gen4
soc: imx: add i.MX8MP HDMI blk-ctrl
soc: imx: imx8m-blk-ctrl: Add i.MX8MP media blk-ctrl
soc: imx: add i.MX8MP HSIO blk-ctrl
soc: imx: imx8m-blk-ctrl: set power device name
soc: qcom: llcc: Add sc8180x and sc8280xp configurations
dt-bindings: arm: msm: Add sc8180x and sc8280xp LLCC compatibles
soc/tegra: pmc: Select REGMAP
dt-bindings: reset: st,sti-powerdown: Convert to yaml
dt-bindings: reset: st,sti-picophyreset: Convert to yaml
dt-bindings: reset: socfpga: Convert to yaml
dt-bindings: reset: snps,axs10x-reset: Convert to yaml
...
New compatible to manage clock and reset of STM32MP13 SoC.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@foss.st.com>
Link: https://lore.kernel.org/r/20220516070600.7692-2-gabriel.fernandez@foss.st.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This adds some improvements on Tegra234 (QSPI, CCPLEX), improves the
SDMMC clock speed on Tegra194 and adds the ASRC audio block on various
chip generations. Memory controller channels are also added on Tegra186
and later and the missing DFLL reset is added for Tegra210.
-----BEGIN PGP SIGNATURE-----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=KBZh
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=wsbV
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.19-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/dt
arm64: tegra: Device tree changes for v5.19-rc1
This adds some improvements on Tegra234 (QSPI, CCPLEX), improves the
SDMMC clock speed on Tegra194 and adds the ASRC audio block on various
chip generations. Memory controller channels are also added on Tegra186
and later and the missing DFLL reset is added for Tegra210.
* tag 'tegra-for-5.19-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: Add missing DFLL reset on Tegra210
arm64: tegra: Add memory controller channels
arm64: tegra: Enable ASRC on various platforms
arm64: tegra: Add ASRC device on Tegra186 and later
arm64: tegra: Update PWM fan node name
arm64: tegra: Add node for Tegra234 CCPLEX cluster
arm64: tegra: Add QSPI controllers on Tegra234
arm64: tegra: Update SDMMC1/3 clock source for Tegra194
Link: https://lore.kernel.org/r/20220506143005.3916655-5-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
As we only have one SCMI instance, it's not necessary to add an index to
the name.
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Acked-by: Rob Herring <robh@kernel.org>
Add DT bindings for the Meson-S4 SoC Reset Controller include file.
Signed-off-by: Zelong Dong <zelong.dong@amlogic.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20220107023931.13251-3-zelong.dong@amlogic.com
This adds the QSPI controllers on the Tegra234 SoC and populates the
SPI NOR flash device for the Jetson AGX Orin platform.
Signed-off-by: Ashish Singhal <ashishsingha@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reset the DSI hardware is needed to prevent different settings between
the bootloader and the kernel.
Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220318144534.17996-20-allen-kh.cheng@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
clk_set_rate_range() works so that the frequency is re-evaulated each time the
rate is changed. Previously we wouldn't let clk providers see a rate that was
different if it was still within the range, which could be bad for power if the
clk could run slower when a range expands. Now the clk provider can decide to
do something differently when the constraints change. This broke Nvidia's clk
driver so we had to wait for the fix for that to bake a little more in -next.
The rate range patch series also introduced a kunit suite for the clk framework
that we're going to extend in the next release. It already made it easy to find
corner cases in the rate range patches so I'm excited to see it cover more clk
code and increase our confidence in core framework patches in the future. I
also added a kunit test for the basic clk gate code and that work will continue
to cover more basic clk types: muxes, dividers, etc.
Beyond the core code we have the usual set of clk driver updates and additions.
Qualcomm again dominates the diffstat here with lots more SoCs being supported
and i.MX follows afer that with a similar number of SoCs gaining clk drivers.
Beyond those large additions there's drivers being modernized to use
clk_parent_data so we can move away from global string names for all the clks
in an SoC. Finally there's lots of little fixes all over the clk drivers for
typos, warnings, and missing clks that aren't critical and get batched up
waiting for the next merge window to open. Nothing super big stands out in the
driver pile. Full details are below.
Core:
- Make clk_set_rate_range() re-evaluate the limits each time
- Introduce various clk_set_rate_range() tests
- Add clk_drop_range() to drop a previously set range
New Drivers:
- i.MXRT1050 clock driver and bindings
- i.MX8DXL clock driver and bindings
- i.MX93 clock driver and bindings
- NCO blocks on Apple SoCs
- Audio clks on StarFive JH7100 RISC-V SoC
- Add support for the new Renesas RZ/V2L SoC
- Qualcomm SDX65 A7 PLL
- Qualcomm SM6350 GPU clks
- Qualcomm SM6125, SM6350, QCS2290 display clks
- Qualcomm MSM8226 multimedia clks
Updates:
- Kunit tests for clk-gate implementation
- Terminate arrays with sentinels and make that clearer
- Cleanup SPDX tags
- Fix typos in comments
- Mark mux table as const in clk-mux
- Make the all_lists array const
- Convert Cirrus Logic CS2000P driver to regmap, yamlify DT binding and add
support for dynamic mode
- Clock configuration on Microchip PolarFire SoCs
- Free allocations on probe error in Mediatek clk driver
- Modernize Mediatek clk driver by consolidating code
- Add watchdog (WDT), I2C, and pin function controller (PFC) clocks on
Renesas R-Car S4-8
- Improve the clocks for the Rockchip rk3568 display outputs (parenting, pll-rates)
- Use of_device_get_match_data() instead of open-coding on Rockchip rk3568
- Reintroduce the expected fractional-divider behaviour that disappeared
with the addition of CLK_FRAC_DIVIDER_POWER_OF_TWO_PS
- Remove SYS PLL 1/2 clock gates for i.MX8M*
- Remove AUDIO MCLK ROOT from i.MX7D
- Add fracn gppll clock type used by i.MX93
- Add new composite clock for i.MX93
- Add missing media mipi phy ref clock for i.MX8MP
- Fix off by one in imx_lpcg_parse_clks_from_dt()
- Rework for the imx pll14xx
- sama7g5: One low priority fix for GCLK of PDMC
- Add DMA engine (SYS-DMAC) clocks on Renesas R-Car S4-8
- Add MOST (MediaLB I/F) clocks on Renesas R-Car E3 and D3
- Add CAN-FD clocks on Renesas R-Car V3U
- Qualcomm SC8280XP RPMCC
- Add some missing clks on Qualcomm MSM8992/MSM8994/MSM8998 SoCs
- Rework Qualcomm GCC bindings and convert SDM845 camera bindig to YAML
- Convert various Qualcomm drivers to use clk_parent_data
- Remove test clocks from various Qualcomm drivers
- Crypto engine clks on Qualcomm IPQ806x + more freqs for SDCC/NSS
- Qualcomm SM8150 EMAC, PCIe, UFS GDSCs
- Better pixel clk frequency support on Qualcomm RCG2 clks
-----BEGIN PGP SIGNATURE-----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=fP8L
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"There's one large change in the core clk framework here. We change how
clk_set_rate_range() works so that the frequency is re-evaulated each
time the rate is changed. Previously we wouldn't let clk providers see
a rate that was different if it was still within the range, which
could be bad for power if the clk could run slower when a range
expands. Now the clk provider can decide to do something differently
when the constraints change. This broke Nvidia's clk driver so we had
to wait for the fix for that to bake a little more in -next.
The rate range patch series also introduced a kunit suite for the clk
framework that we're going to extend in the next release. It already
made it easy to find corner cases in the rate range patches so I'm
excited to see it cover more clk code and increase our confidence in
core framework patches in the future. I also added a kunit test for
the basic clk gate code and that work will continue to cover more
basic clk types: muxes, dividers, etc.
Beyond the core code we have the usual set of clk driver updates and
additions. Qualcomm again dominates the diffstat here with lots more
SoCs being supported and i.MX follows afer that with a similar number
of SoCs gaining clk drivers. Beyond those large additions there's
drivers being modernized to use clk_parent_data so we can move away
from global string names for all the clks in an SoC. Finally there's
lots of little fixes all over the clk drivers for typos, warnings, and
missing clks that aren't critical and get batched up waiting for the
next merge window to open. Nothing super big stands out in the driver
pile. Full details are below.
Core:
- Make clk_set_rate_range() re-evaluate the limits each time
- Introduce various clk_set_rate_range() tests
- Add clk_drop_range() to drop a previously set range
New Drivers:
- i.MXRT1050 clock driver and bindings
- i.MX8DXL clock driver and bindings
- i.MX93 clock driver and bindings
- NCO blocks on Apple SoCs
- Audio clks on StarFive JH7100 RISC-V SoC
- Add support for the new Renesas RZ/V2L SoC
- Qualcomm SDX65 A7 PLL
- Qualcomm SM6350 GPU clks
- Qualcomm SM6125, SM6350, QCS2290 display clks
- Qualcomm MSM8226 multimedia clks
Updates:
- Kunit tests for clk-gate implementation
- Terminate arrays with sentinels and make that clearer
- Cleanup SPDX tags
- Fix typos in comments
- Mark mux table as const in clk-mux
- Make the all_lists array const
- Convert Cirrus Logic CS2000P driver to regmap, yamlify DT binding
and add support for dynamic mode
- Clock configuration on Microchip PolarFire SoCs
- Free allocations on probe error in Mediatek clk driver
- Modernize Mediatek clk driver by consolidating code
- Add watchdog (WDT), I2C, and pin function controller (PFC) clocks
on Renesas R-Car S4-8
- Improve the clocks for the Rockchip rk3568 display outputs
(parenting, pll-rates)
- Use of_device_get_match_data() instead of open-coding on Rockchip
rk3568
- Reintroduce the expected fractional-divider behaviour that
disappeared with the addition of CLK_FRAC_DIVIDER_POWER_OF_TWO_PS
- Remove SYS PLL 1/2 clock gates for i.MX8M*
- Remove AUDIO MCLK ROOT from i.MX7D
- Add fracn gppll clock type used by i.MX93
- Add new composite clock for i.MX93
- Add missing media mipi phy ref clock for i.MX8MP
- Fix off by one in imx_lpcg_parse_clks_from_dt()
- Rework for the imx pll14xx
- sama7g5: One low priority fix for GCLK of PDMC
- Add DMA engine (SYS-DMAC) clocks on Renesas R-Car S4-8
- Add MOST (MediaLB I/F) clocks on Renesas R-Car E3 and D3
- Add CAN-FD clocks on Renesas R-Car V3U
- Qualcomm SC8280XP RPMCC
- Add some missing clks on Qualcomm MSM8992/MSM8994/MSM8998 SoCs
- Rework Qualcomm GCC bindings and convert SDM845 camera bindig to
YAML
- Convert various Qualcomm drivers to use clk_parent_data
- Remove test clocks from various Qualcomm drivers
- Crypto engine clks on Qualcomm IPQ806x + more freqs for SDCC/NSS
- Qualcomm SM8150 EMAC, PCIe, UFS GDSCs
- Better pixel clk frequency support on Qualcomm RCG2 clks"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (227 commits)
clk: zynq: Update the parameters to zynq_clk_register_periph_clk
clk: zynq: trivial warning fix
clk: Drop the rate range on clk_put()
clk: test: Test clk_set_rate_range on orphan mux
clk: Initialize orphan req_rate
dt-bindings: clock: drop useless consumer example
dt-bindings: clock: renesas: Make example 'clocks' parsable
clk: qcom: gcc-msm8994: Fix gpll4 width
dt-bindings: clock: fix dt_binding_check error for qcom,gcc-other.yaml
clk: rs9: Add Renesas 9-series PCIe clock generator driver
clk: fixed-factor: Introduce devm_clk_hw_register_fixed_factor_index()
clk: visconti: prevent array overflow in visconti_clk_register_gates()
dt-bindings: clk: rs9: Add Renesas 9-series I2C PCIe clock generator
clk: sifive: Move all stuff into SoCs header files from C files
clk: sifive: Add SoCs prefix in each SoCs-dependent data
riscv: dts: Change the macro name of prci in each device node
dt-bindings: change the macro name of prci in header files and example
clk: sifive: duplicate the macro definitions for the time being
clk: qcom: sm6125-gcc: fix typos in comments
clk: ti: clkctrl: fix typos in comments
...
Here is the big set of staging driver updates for 5.18-rc1.
Loads of tiny cleanups for almost all staging drivers in here, nothing
major at all. Highlights include:
- remove the ashmem Android driver. It is long-dead and if
there are any legacy userspace applications still using it,
the Android kernel images will maintain it, the community
shouldn't care about it anymore
- wfx wifi driver major cleanups. Should be ready to merge out
of staging soon, and will coordinate with the wifi maintainers
after -rc1 is out
- major cleanups and unwinding of the layers of the r8188eu
driver. It's amazing just how many unneeded layers of
abstraction is in there, just when we think it's done, another
is found...
- lots of tiny coding style cleanups in many other staging
drivers.
There will be merge conflict with a fbtft change and the spi driver
changes in your tree, but it's pretty obvious what to do (the function
shouldn't return anything.)
All have been in linux-next for a while with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYkG1cA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylndwCfVhxKnbTYKtOs6UEr5pgPCoQCioUAn0Y2i0TG
4aFeeKUyL8VGdAitL+tp
=E6v7
-----END PGP SIGNATURE-----
Merge tag 'staging-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver updates from Greg KH:
"Here is the big set of staging driver updates for 5.18-rc1.
Loads of tiny cleanups for almost all staging drivers in here, nothing
major at all. Highlights include:
- remove the ashmem Android driver. It is long-dead and if there are
any legacy userspace applications still using it, the Android
kernel images will maintain it, the community shouldn't care about
it anymore
- wfx wifi driver major cleanups. Should be ready to merge out of
staging soon, and will coordinate with the wifi maintainers after
-rc1 is out
- major cleanups and unwinding of the layers of the r8188eu driver.
It's amazing just how many unneeded layers of abstraction is in
there, just when we think it's done, another is found...
- lots of tiny coding style cleanups in many other staging drivers.
All have been in linux-next for a while with no reported problems"
* tag 'staging-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (455 commits)
staging: r8188eu: remove unnecessary memset in r8188eu
staging: greybus: introduce pwm_ops::apply
staging: rts5208: Resolve checkpatch.pl issues.
staging: sm750fb: fix naming style
staging: fbtft: Consider type of init sequence values in fbtft_init_display()
staging: fbtft: Constify buf parameter in fbtft_dbg_hex()
staging: mmal-vchiq: clear redundant item named bulk_scratch
mips: dts: ralink: add MT7621 SoC
staging: r8188eu: remove some unused local ieee80211 macros
staging: r8188eu: make rtl8188e_process_phy_info static
staging: r8188eu: remove unused function prototype
staging: r8188eu: remove three unused receive defines
staging: r8188eu: remove unnecessary initializations
staging: rtl8192e: Fix spelling mistake "RESQUEST" -> "REQUEST"
MAINTAINERS: remove the obsolete file entry for staging in ANDROID DRIVERS
staging: r8188eu: proper error handling in rtw_init_drv_sw
staging: r8188eu: call _cancel_timer_ex from _rtw_free_recv_priv
staging: vt6656: Removed unused variable vt3342_vnt_threshold
staging: vt6656: Removed unused variable bb_vga_0
staging: remove ashmem
...
Here is the big set of char/misc and other small driver subsystem
updates for 5.18-rc1.
Included in here are merges from driver subsystems which contain:
- iio driver updates and new drivers
- fsi driver updates
- fpga driver updates
- habanalabs driver updates and support for new hardware
- soundwire driver updates and new drivers
- phy driver updates and new drivers
- coresight driver updates
- icc driver updates
Individual changes include:
- mei driver updates
- interconnect driver updates
- new PECI driver subsystem added
- vmci driver updates
- lots of tiny misc/char driver updates
There will be two merge conflicts with your tree, one in MAINTAINERS
which is obvious to fix up, and one in drivers/phy/freescale/Kconfig
which also should be easy to resolve.
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYkG3fQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykNEgCfaRG8CRxewDXOO4+GSeA3NGK+AIoAnR89donC
R4bgCjfg8BWIBcVVXg3/
=WWXC
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc and other driver updates from Greg KH:
"Here is the big set of char/misc and other small driver subsystem
updates for 5.18-rc1.
Included in here are merges from driver subsystems which contain:
- iio driver updates and new drivers
- fsi driver updates
- fpga driver updates
- habanalabs driver updates and support for new hardware
- soundwire driver updates and new drivers
- phy driver updates and new drivers
- coresight driver updates
- icc driver updates
Individual changes include:
- mei driver updates
- interconnect driver updates
- new PECI driver subsystem added
- vmci driver updates
- lots of tiny misc/char driver updates
All of these have been in linux-next for a while with no reported
problems"
* tag 'char-misc-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (556 commits)
firmware: google: Properly state IOMEM dependency
kgdbts: fix return value of __setup handler
firmware: sysfb: fix platform-device leak in error path
firmware: stratix10-svc: add missing callback parameter on RSU
arm64: dts: qcom: add non-secure domain property to fastrpc nodes
misc: fastrpc: Add dma handle implementation
misc: fastrpc: Add fdlist implementation
misc: fastrpc: Add helper function to get list and page
misc: fastrpc: Add support to secure memory map
dt-bindings: misc: add fastrpc domain vmid property
misc: fastrpc: check before loading process to the DSP
misc: fastrpc: add secure domain support
dt-bindings: misc: add property to support non-secure DSP
misc: fastrpc: Add support to get DSP capabilities
misc: fastrpc: add support for FASTRPC_IOCTL_MEM_MAP/UNMAP
misc: fastrpc: separate fastrpc device from channel context
dt-bindings: nvmem: brcm,nvram: add basic NVMEM cells
dt-bindings: nvmem: make "reg" property optional
nvmem: brcm_nvram: parse NVRAM content into NVMEM cells
nvmem: dt-bindings: Fix the error of dt-bindings check
...
Add header for the Delta TN48M CPLD provided
resets.
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Link: https://lore.kernel.org/r/20220131133049.77780-4-robert.marko@sartura.hr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the clocks and resets used by the PCIe hardware found on
Tegra234 SoCs.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
they're mostly minor cleanups and some debugfs stuff. The real work
that's in here is the typical pile of clk driver updates and new SoC
support. Per usual (or maybe just recent trends), Qualcomm gains a
handful of SoC drivers additions and has the largest diffstat. After
that there are quite a few updates to the Allwinner (sunxi) drivers to
support modular drivers and Renesas is heavily updated to add more
support for various clks. Overall it looks pretty normal.
New Drivers:
- Add MDMA and BDMA clks to Ingenic JZ4760 and JZ4770
- MediaTek mt7986 SoC basic support
- Clock and reset driver for Toshiba Visconti SoCs
- Initial clock driver for the Exynos7885 SoC (Samsung Galaxy A8)
- Allwinner D1 clks
- Lan966x Generic Clock Controller driver and associated DT bindings
- Qualcomm SDX65, SM8450, and MSM8976 GCC clks
- Qualcomm SDX65 and SM8450 RPMh clks
Updates:
- Set suppress_bind_attrs to true for i.MX8ULP driver
- Switch from do_div to div64_ul for throughout all i.MX drivers
- Fix imx8mn_clko1_sels for i.MX8MN
- Remove unused IPG_AUDIO_ROOT from i.MX8MP
- Switch parent for audio_root_clk to audio ahb in i.MX8MP driver
- Removal of all remaining uses of __clk_lookup() in drivers/clk/samsung
- Refactoring of the CPU clocks registration to use common interface
- An update of the Exynos850 driver (support for more clock domains)
required by the E850-96 development board
- Prep for runtime PM and generic power domains on Tegra
- Support modular Allwinner clk drivers via platform bus
- Lan966x clock driver extended to support clock gating
- Add serial (SCI1), watchdog (WDT), timer (OSTM), SPI (RSPI), and
thermal (TSU) clocks and resets on Renesas RZ/G2L
- Rework SDHI clock handling in the Renesas R-Car Gen3 and RZ/G2 clock
drivers, and in the Renesas SDHI driver
- Make the Cortex-A55 (I) clock on Renesas RZ/G2L programmable
- Document support for the new Renesas R-Car S4-8 (R8A779F0) SoC
- Add support for the new Renesas R-Car S4-8 (R8A779F0) SoC
- Add GPU clock and resets on Renesas RZ/G2L
- Add clk-provider.h to various Qualcomm clk drivers
- devm version of clk_hw_register_gate()
- kerneldoc fixes in a couple drivers
-----BEGIN PGP SIGNATURE-----
iQJFBAABCAAvFiEE9L57QeeUxqYDyoaDrQKIl8bklSUFAmHfOa8RHHNib3lkQGtl
cm5lbC5vcmcACgkQrQKIl8bklSX+Ew/9FaQLRh3ahN+qF8VMJ1K9qUciYBlU+UtC
excKfTkJg+1JGMP8dGSRSi/aC/UyLPb0dJDRMKcSZPYIScP+wc3HJHm4i+CpxDcn
/wXPW3tvY1CkVq1P7/baesoNiIle5zqpl4+0w9CN5KuoXctc35Pr1GqJ/C0XsDfQ
DS3lpck65tr7Wy1muChT1ZR+7hGv6K7olR7FDYNVSDtfJcaOZENSLgbPF6eea0FR
/dl+6o1COF23XAGF1GJg88DYRgnEqxLsfFTaC6Hz8DeQdKBVh9GF6tpgLhk7vsaG
gcRZxU24KaUw0lNZGdzmagy8ZJ6aZhcuzXQKN9VecbTIhRYNTWmB1VsvbhhEVb1T
96kBAp/II1JZdh/8W7uOmg4Ahupap5+f6JKMfR3zD4aDXkNDsxyXBA5AXtC0GPGN
5340WiJsBz/dD9/YE+mQ7YZKhdvKaGEVbmVUpQHceapeTBk4EIHKSVIq5sKd7qiq
ZHxOIizx5MgBJyoSeIxkB3j0KvwSTDNz6WM2F9gnNNtGfuSlA4NAnO1davINNQun
+seP+deBviUl+P2u9iodRApfCiEuM3mA548KTba/Z1nJ7sN93/qrqr1FBAUSqY+k
xNRXfXIzlOY9ifm6PlvU8QUK0XVtKjt0ld7pFzRkf6EU523DwzL2I2XIY2Eve2vA
LaDihwcKyR0=
=jB+l
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"We have a couple patches in the framework core this time around but
they're mostly minor cleanups and some debugfs stuff. The real work
that's in here is the typical pile of clk driver updates and new SoC
support.
Per usual (or maybe just recent trends), Qualcomm gains a handful of
SoC drivers additions and has the largest diffstat. After that there
are quite a few updates to the Allwinner (sunxi) drivers to support
modular drivers and Renesas is heavily updated to add more support for
various clks.
Overall it looks pretty normal.
New Drivers:
- Add MDMA and BDMA clks to Ingenic JZ4760 and JZ4770
- MediaTek mt7986 SoC basic support
- Clock and reset driver for Toshiba Visconti SoCs
- Initial clock driver for the Exynos7885 SoC (Samsung Galaxy A8)
- Allwinner D1 clks
- Lan966x Generic Clock Controller driver and associated DT bindings
- Qualcomm SDX65, SM8450, and MSM8976 GCC clks
- Qualcomm SDX65 and SM8450 RPMh clks
Updates:
- Set suppress_bind_attrs to true for i.MX8ULP driver
- Switch from do_div to div64_ul for throughout all i.MX drivers
- Fix imx8mn_clko1_sels for i.MX8MN
- Remove unused IPG_AUDIO_ROOT from i.MX8MP
- Switch parent for audio_root_clk to audio ahb in i.MX8MP driver
- Removal of all remaining uses of __clk_lookup() in
drivers/clk/samsung
- Refactoring of the CPU clocks registration to use common interface
- An update of the Exynos850 driver (support for more clock domains)
required by the E850-96 development board
- Prep for runtime PM and generic power domains on Tegra
- Support modular Allwinner clk drivers via platform bus
- Lan966x clock driver extended to support clock gating
- Add serial (SCI1), watchdog (WDT), timer (OSTM), SPI (RSPI), and
thermal (TSU) clocks and resets on Renesas RZ/G2L
- Rework SDHI clock handling in the Renesas R-Car Gen3 and RZ/G2
clock drivers, and in the Renesas SDHI driver
- Make the Cortex-A55 (I) clock on Renesas RZ/G2L programmable
- Document support for the new Renesas R-Car S4-8 (R8A779F0) SoC
- Add support for the new Renesas R-Car S4-8 (R8A779F0) SoC
- Add GPU clock and resets on Renesas RZ/G2L
- Add clk-provider.h to various Qualcomm clk drivers
- devm version of clk_hw_register_gate()
- kerneldoc fixes in a couple drivers"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (131 commits)
clk: visconti: Remove pointless NULL check in visconti_pll_add_lookup()
clk: mediatek: add mt7986 clock support
clk: mediatek: add mt7986 clock IDs
dt-bindings: clock: mediatek: document clk bindings for mediatek mt7986 SoC
clk: mediatek: clk-gate: Use regmap_{set/clear}_bits helpers
clk: mediatek: clk-gate: Shrink by adding clockgating bit check helper
clk: x86: Fix clk_gate_flags for RV_CLK_GATE
clk: x86: Use dynamic con_id string during clk registration
ACPI: APD: Add a fmw property clk-name
drivers: acpi: acpi_apd: Remove unused device property "is-rv"
x86: clk: clk-fch: Add support for newer family of AMD's SOC
clk: ingenic: Add MDMA and BDMA clocks
dt-bindings: clk/ingenic: Add MDMA and BDMA clocks
clk: bm1880: remove kfrees on static allocations
clk: Drop unused COMMON_CLK_STM32MP157_SCMI config
clk: st: clkgen-mux: search reg within node or parent
clk: st: clkgen-fsyn: search reg within node or parent
clk: Enable/Disable runtime PM for clk_summary
MAINTAINERS: Add entries for Toshiba Visconti PLL and clock controller
clk: visconti: Add support common clock driver and reset driver
...
- Clock and reset driver for Toshiba Visconti SoCs
* clk-socfpga:
clk: socfpga: s10: Make use of the helper function devm_platform_ioremap_resource()
clk: socfpga: agilex: Make use of the helper function devm_platform_ioremap_resource()
clk: socfpga: remove redundant assignment after a mask operation
clk: socfpga: remove redundant assignment on division
* clk-toshiba:
clk: visconti: Remove pointless NULL check in visconti_pll_add_lookup()
MAINTAINERS: Add entries for Toshiba Visconti PLL and clock controller
clk: visconti: Add support common clock driver and reset driver
dt-bindings: clock: Add DT bindings for SMU of Toshiba Visconti TMPV770x SoC
dt-bindings: clock: Add DT bindings for PLL of Toshiba Visconti TMPV770x SoC
* clk-st:
clk: Drop unused COMMON_CLK_STM32MP157_SCMI config
clk: st: clkgen-mux: search reg within node or parent
clk: st: clkgen-fsyn: search reg within node or parent
* clk-bitmain:
clk: bm1880: remove kfrees on static allocations
This adds support for the StarFive JH7100, including the necessary
device drivers and DT files for the BeagleV Starlight prototype
board, with additional boards to be added later. This SoC promises
to be the first usable low-cost platform for RISC-V.
I've taken this through the SoC tree in the anticipation of adding
a few other Arm based SoCs as well, but those did not pass the
review in time, so it's only this one.
-----BEGIN PGP SIGNATURE-----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=X5uk
-----END PGP SIGNATURE-----
Merge tag 'newsoc-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull RISC-V SoC updates from Arnd Bergmann:
"Add support for StarFive JH7100 RISC-V SoC
This adds support for the StarFive JH7100, including the necessary
device drivers and DT files for the BeagleV Starlight prototype board,
with additional boards to be added later. This SoC promises to be the
first usable low-cost platform for RISC-V.
I've taken this through the SoC tree in the anticipation of adding a
few other Arm based SoCs as well, but those did not pass the review in
time, so it's only this one"
* tag 'newsoc-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
reset: starfive-jh7100: Fix 32bit compilation
RISC-V: Add BeagleV Starlight Beta device tree
RISC-V: Add initial StarFive JH7100 device tree
serial: 8250_dw: Add StarFive JH7100 quirk
dt-bindings: serial: snps-dw-apb-uart: Add JH7100 uarts
pinctrl: starfive: Add pinctrl driver for StarFive SoCs
dt-bindings: pinctrl: Add StarFive JH7100 bindings
dt-bindings: pinctrl: Add StarFive pinctrl definitions
reset: starfive-jh7100: Add StarFive JH7100 reset driver
dt-bindings: reset: Add Starfive JH7100 reset bindings
dt-bindings: reset: Add StarFive JH7100 reset definitions
clk: starfive: Add JH7100 clock generator driver
dt-bindings: clock: starfive: Add JH7100 bindings
dt-bindings: clock: starfive: Add JH7100 clock definitions
dt-bindings: interrupt-controller: Add StarFive JH7100 plic
dt-bindings: timer: Add StarFive JH7100 clint
RISC-V: Add StarFive SoC Kconfig option
Add all resets for the StarFive JH7100 reset controller.
Based on work by Ahmad Fatoum for Barebox, with "JH7100_" prefixes added
to all definitions.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Add a few more clocks that will be used in follow-up patches to enable
more functionality on Tegra234.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The D1 has a CCU and a R_CCU (PRCM CCU) like most other sunxi SoCs, with
3 and 4 clock inputs, respectively. Add the compatibles and bindings.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20211119043545.4010-2-samuel@sholland.org
terms of lines it's mainly Qualcomm and Mediatek code, supporting
various SoCs and their multitude of clk controllers.
New Drivers:
- GCC and RPMcc support for Qualcomm QCM2290 SoCs
- GCC support for Qualcomm MSM8994/MSM8992 SoCs
- LPASSCC and CAMCC support for Qualcomm SC7280 SoCs
- Support for Mediatek MT8195 SoCs
- Initial clock driver for the Exynos850 SoC
- Add i.MX8ULP clock driver and related bindings
Updates:
- Clock power management for new SAMA7G5 SoC
- Updates to the master clock driver and sam9x60-pll to be able to use
cpufreq-dt driver and avoid overclocking of CPU and MCK0 domains while
changing the frequency via DVFS
- Use ARRAY_SIZE in qcom clk drivers
- Remove some impractical fallback parent names in qcom clk drivers
- Make Mediatek clk drivers tristate
- Refactoring of the CPU clock code and conversion of Samsung Exynos5433
CPU clock driver to the platform driver
- A few conversions to devm_platform_ioremap_resource()
- Updates of the Samsung Kconfig help text
- Update video path realted clocks for Amlogic meson8
- Add SPI Multi I/O Bus and SDHI clocks and resets on Renesas RZ/G2L
- Add SPI Multi I/O Bus (RPC) clocks on Renesas R-Car V3U
- Add MediaLB clocks on Renesas R-Car H3, M3-W/W+, and M3-N
- Remove unused helpers from i.MX specific clock header
- Rework all i.MX clk based helpers to use clk_hw based ones
- Rework i.MX gate/mux/divider wrappers
- Rework imx_clk_hw_composite and imx_clk_hw_pll14xx wrappers
- Update i.MX pllv4 and composite clocks to support i.MX8ULP
- Disable i.MX7ULP composite clock during initialization
- Add CLK_SET_RATE_NO_REPARENT flag to the i.MX7ULP composite
- Disable the i.MX pfd when set pfdv2 clock rate
- Add support for i.MX8ULP in pfdv2
- Add the pcc reset controller support on i.MX8ULP
- Fix the build break when clk-imx8ulp is built as module
- Move csi_sel mux to correct base register in i.MX6UL clock drivr
- Fix csi clk gate register in i.MX6UL clock driver
- Fix build bug making CLK_IMX8ULP select MXC_CLK
- Add TPU (PWM), and Z (Cortex-A76) clocks on Renesas R-Car V3U
- Add Ethernet clocks on Renesas RZ/G2L
- Move Rockchip to use module_platform_probe
- Enable usage of Coresight related clocks on Rockchip rk3399
-----BEGIN PGP SIGNATURE-----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=Is+O
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"The usual collection of clk driver updates and new driver additions.
In terms of lines it's mainly Qualcomm and Mediatek code, supporting
various SoCs and their multitude of clk controllers.
New Drivers:
- GCC and RPMcc support for Qualcomm QCM2290 SoCs
- GCC support for Qualcomm MSM8994/MSM8992 SoCs
- LPASSCC and CAMCC support for Qualcomm SC7280 SoCs
- Support for Mediatek MT8195 SoCs
- Initial clock driver for the Exynos850 SoC
- Add i.MX8ULP clock driver and related bindings
Updates:
- Clock power management for new SAMA7G5 SoC
- Updates to the master clock driver and sam9x60-pll to be able to
use cpufreq-dt driver and avoid overclocking of CPU and MCK0
domains while changing the frequency via DVFS
- Use ARRAY_SIZE in qcom clk drivers
- Remove some impractical fallback parent names in qcom clk drivers
- Make Mediatek clk drivers tristate
- Refactoring of the CPU clock code and conversion of Samsung
Exynos5433 CPU clock driver to the platform driver
- A few conversions to devm_platform_ioremap_resource()
- Updates of the Samsung Kconfig help text
- Update video path realted clocks for Amlogic meson8
- Add SPI Multi I/O Bus and SDHI clocks and resets on Renesas RZ/G2L
- Add SPI Multi I/O Bus (RPC) clocks on Renesas R-Car V3U
- Add MediaLB clocks on Renesas R-Car H3, M3-W/W+, and M3-N
- Remove unused helpers from i.MX specific clock header
- Rework all i.MX clk based helpers to use clk_hw based ones
- Rework i.MX gate/mux/divider wrappers
- Rework imx_clk_hw_composite and imx_clk_hw_pll14xx wrappers
- Update i.MX pllv4 and composite clocks to support i.MX8ULP
- Disable i.MX7ULP composite clock during initialization
- Add CLK_SET_RATE_NO_REPARENT flag to the i.MX7ULP composite
- Disable the i.MX pfd when set pfdv2 clock rate
- Add support for i.MX8ULP in pfdv2
- Add the pcc reset controller support on i.MX8ULP
- Fix the build break when clk-imx8ulp is built as module
- Move csi_sel mux to correct base register in i.MX6UL clock drivr
- Fix csi clk gate register in i.MX6UL clock driver
- Fix build bug making CLK_IMX8ULP select MXC_CLK
- Add TPU (PWM), and Z (Cortex-A76) clocks on Renesas R-Car V3U
- Add Ethernet clocks on Renesas RZ/G2L
- Move Rockchip to use module_platform_probe
- Enable usage of Coresight related clocks on Rockchip rk3399"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (170 commits)
clk: use clk_core_get_rate_recalc() in clk_rate_get()
clk: at91: sama7g5: set low limit for mck0 at 32KHz
clk: at91: sama7g5: remove prescaler part of master clock
clk: at91: clk-master: add notifier for divider
clk: at91: clk-sam9x60-pll: add notifier for div part of PLL
clk: at91: clk-master: fix prescaler logic
clk: at91: clk-master: mask mckr against layout->mask
clk: at91: clk-master: check if div or pres is zero
clk: at91: sam9x60-pll: use DIV_ROUND_CLOSEST_ULL
clk: at91: pmc: add sama7g5 to the list of available pmcs
clk: at91: clk-master: improve readability by using local variables
clk: at91: clk-master: add register definition for sama7g5's master clock
clk: at91: sama7g5: add securam's peripheral clock
clk: at91: pmc: execute suspend/resume only for backup mode
clk: at91: re-factor clocks suspend/resume
clk: ux500: Add driver for the reset portions of PRCC
dt-bindings: clock: u8500: Rewrite in YAML and extend
clk: composite: Use rate_ops.determine_rate when also a mux is available
clk: samsung: describe drivers in Kconfig
clk: samsung: exynos5433: update apollo and atlas clock probing
...
* clk-imx: (21 commits)
clk: imx: Make CLK_IMX8ULP select MXC_CLK
clk: imx: imx6ul: Fix csi clk gate register
clk: imx: imx6ul: Move csi_sel mux to correct base register
clk: imx: Fix the build break when clk-imx8ulp build as module
clk: imx: Add the pcc reset controller support on imx8ulp
clk: imx: Add clock driver for imx8ulp
clk: imx: Update the pfdv2 for 8ulp specific support
clk: imx: disable the pfd when set pfdv2 clock rate
clk: imx: Add 'CLK_SET_RATE_NO_REPARENT' for composite-7ulp
clk: imx: disable i.mx7ulp composite clock during initialization
clk: imx: Update the compsite driver to support imx8ulp
clk: imx: Update the pllv4 to support imx8ulp
dt-bindings: clock: Add imx8ulp clock support
clk: imx: Rework imx_clk_hw_pll14xx wrapper
clk: imx: Rework all imx_clk_hw_composite wrappers
clk: imx: Rework all clk_hw_register_divider wrappers
clk: imx: Rework all clk_hw_register_mux wrappers
clk: imx: Rework all clk_hw_register_gate2 wrappers
clk: imx: Rework all clk_hw_register_gate wrappers
clk: imx: Make mux/mux2 clk based helpers use clk_hw based ones
...
* clk-ux500:
clk: ux500: Add driver for the reset portions of PRCC
dt-bindings: clock: u8500: Rewrite in YAML and extend
* clk-debugfs:
clk: use clk_core_get_rate_recalc() in clk_rate_get()
This rewrites the ux500/u8500 clock bindings in YAML schema and extends them
with the PRCC reset controller.
The bindings are a bit idiomatic but it just reflects their age, the ux500
platform was used as guinea pig for early device tree conversion of platforms
in 2015. The new subnode for the reset controller follows the pattern of the
old bindings and adds a node with reset-cells for this.
Cc: devicetree@vger.kernel.org
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210921184803.1757916-1-linus.walleij@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Reset the DSI hardware is needed to prevent different settings between
the bootloader and the kernel.
While here, also remove the undocumented and also not used
'mediatek,syscon-dsi' property.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210930103105.v4.5.I933f1532d7a1b2910843a9644c86a7d94a4b44e1@changeid
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The DT binding includes for reset controllers are located in
include/dt-bindings/reset/. Move the Mediatek reset constants in there.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/20210930103105.v4.1.I514d9aafff3a062f751b37d3fea7402f67595b86@changeid
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add the clock dt-binding file for i.MX8ULP.
For pcc node, it will also be used as a reset controller,
so add the '#reset-cells' property description and add the
pcc reset IDs.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20210914065208.3582128-2-ping.bai@nxp.com
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Add ID to SCMI0 to exposes reset controller for the MCU HOLD BOOT resource.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@foss.st.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210617051814.12018-10-gabriel.fernandez@foss.st.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
stm32mp15 TZ secure firmware provides SCMI reset domains for
secure resources. This change defines the SCMI reset domain
identifiers used by SCMI agents and servers.
Stm32mp15 TZ secure firmware provides SCMI clocks for oscillators, some
PLL output and few secure aware interfaces. This change defines the
SCMI clock identifiers used by SCMI agents and servers.
Server SCMI0 exposes reset controllers for resources under RCC[TZEN]
configuration control.
Signed-off-by: Etienne Carriere <etienne.carriere@foss.st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@foss.st.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210617051814.12018-9-gabriel.fernandez@foss.st.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
I have a handful of new RISC-V related patches for this merge window:
* A check to ensure drivers are properly using uaccess. This isn't
manifesting with any of the drivers I'm currently using, but may catch
errors in new drivers.
* Some preliminary support for the FU740, along with the HiFive
Unleashed it will appear on.
* NUMA support for RISC-V, which involves making the arm64 code generic.
* Support for kasan on the vmalloc region.
* A handful of new drivers for the Kendryte K210, along with the DT
plumbing required to boot on a handful of K210-based boards.
* Support for allocating ASIDs.
* Preliminary support for kernels larger than 128MiB.
* Various other improvements to our KASAN support, including the
utilization of huge pages when allocating the KASAN regions.
We may have already found a bug with the KASAN_VMALLOC code, but it's
passing my tests. There's a fix in the works, but that will probably
miss the merge window.
-----BEGIN PGP SIGNATURE-----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=CutX
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-5.12-mw0' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V updates from Palmer Dabbelt:
"A handful of new RISC-V related patches for this merge window:
- A check to ensure drivers are properly using uaccess. This isn't
manifesting with any of the drivers I'm currently using, but may
catch errors in new drivers.
- Some preliminary support for the FU740, along with the HiFive
Unleashed it will appear on.
- NUMA support for RISC-V, which involves making the arm64 code
generic.
- Support for kasan on the vmalloc region.
- A handful of new drivers for the Kendryte K210, along with the DT
plumbing required to boot on a handful of K210-based boards.
- Support for allocating ASIDs.
- Preliminary support for kernels larger than 128MiB.
- Various other improvements to our KASAN support, including the
utilization of huge pages when allocating the KASAN regions.
We may have already found a bug with the KASAN_VMALLOC code, but it's
passing my tests. There's a fix in the works, but that will probably
miss the merge window.
* tag 'riscv-for-linus-5.12-mw0' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (75 commits)
riscv: Improve kasan population by using hugepages when possible
riscv: Improve kasan population function
riscv: Use KASAN_SHADOW_INIT define for kasan memory initialization
riscv: Improve kasan definitions
riscv: Get rid of MAX_EARLY_MAPPING_SIZE
soc: canaan: Sort the Makefile alphabetically
riscv: Disable KSAN_SANITIZE for vDSO
riscv: Remove unnecessary declaration
riscv: Add Canaan Kendryte K210 SD card defconfig
riscv: Update Canaan Kendryte K210 defconfig
riscv: Add Kendryte KD233 board device tree
riscv: Add SiPeed MAIXDUINO board device tree
riscv: Add SiPeed MAIX GO board device tree
riscv: Add SiPeed MAIX DOCK board device tree
riscv: Add SiPeed MAIX BiT board device tree
riscv: Update Canaan Kendryte K210 device tree
dt-bindings: add resets property to dw-apb-timer
dt-bindings: fix sifive gpio properties
dt-bindings: update sifive uart compatible string
dt-bindings: update sifive clint compatible string
...
Linus Torvalds