libsas power management routines to suspend and recover the sas domain
based on a model where the lldd is allowed and expected to be
"forgetful".
sas_suspend_ha - disable event processing allowing the lldd to take down
links without concern for causing hotplug events.
Regardless of whether the lldd actually posts link down
messages libsas notifies the lldd that all
domain_devices are gone.
sas_prep_resume_ha - on the way back up before the lldd starts link
training clean out any spurious events that were
generated on the way down, and re-enable event
processing
sas_resume_ha - after the lldd has started and decided that all phys
have posted link-up events this routine is called to let
libsas start it's own timeout of any phys that did not
resume. After the timeout an lldd can cancel the
phy teardown by posting a link-up event.
Storage for ex_change_count (u16) and phy_change_count (u8) are changed
to int so they can be set to -1 to indicate 'invalidated'.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Jacek Danecki <jacek.danecki@intel.com>
Tested-by: Maciej Patelczyk <maciej.patelczyk@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Two bits were appended to the end of the bitfield
list in struct scsi_device. Resolve that conflict
by including both bits.
Conflicts:
include/scsi/scsi_device.h
Now that scsi registers its async scan work with the async subsystem,
wait_for_device_probe() is sufficient for ensuring all scanning is
complete.
[jejb: fix merge problems with eea03c20ae Make wait_for_device_probe() also do scsi_complete_async_scans()]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Tested-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Make use of USB quirk method to identify such HDD while reading
the cache status in sd_probe(). If cache quirk is present for
the HDD, lets assume that cache is enabled and make WCE bit
equal to 1.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Pankaj Kumar <pankaj.km@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The timer and the completion are only used for slow path tasks (smp, and
lldd tmfs), yet we incur the allocation space and cpu setup time for
every fast path task.
Cc: Xiangliang Yu <yuxiangl@marvell.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
On the way to add a new sata_device field, noticed that libsas is
carrying port multiplier infrastructure that is explicitly disabled by
sas_discover_sata(). The aic94xx touches the unused port_no, so leave
that field in case there was some use for it.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When recovering failed eh-cmnds let the lldd attempt an abort via
scsi_abort_eh_cmnd before escalating.
Reviewed-by: Jacek Danecki <jacek.danecki@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The strategy handlers may be called in places that are problematic for
libsas (i.e. sata resets outside of domain revalidation filtering /
libata link recovery), or problematic for userspace (non-blocking ioctl
to sleeping reset functions). However, these routines are also called
for eh escalations and recovery of scsi_eh_prep_cmnd(), so permit them
as long as we are running in the host's error handler, otherwise arrange
for them to be triggered in eh_context.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When managing shost->host_eh_scheduled libata assumes that there is a
1:1 shost-to-ata_port relationship. libsas creates a 1:N relationship
so it needs to manage host_eh_scheduled cumulatively at the host level.
The sched_eh and end_eh port port ops allow libsas to track when domain
devices enter/leave the "eh-pending" state under ha->lock (previously
named ha->state_lock, but it is no longer just a lock for ha->state
changes).
Since host_eh_scheduled indicates eh without backing commands pinning
the device it can be deallocated at any time. Move the taking of the
domain_device reference under the port_lock to guarantee that the
ata_port stays around for the duration of eh.
Reviewed-by: Jacek Danecki <jacek.danecki@intel.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Introduce scsi_dh_attached_handler_name() to retrieve the name of the
scsi_dh that is attached to the scsi_device associated with the provided
request queue. Returns NULL if a scsi_dh is not attached.
Also, fix scsi_dh_{attach,detach} function header comments to document
@q rather than @sdev.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Tested-by: Babu Moger <babu.moger@netapp.com>
Reviewed-by: Chandra Seetharaman <sekharan@us.ibm.com>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
During alua transitions, an array can return transitioning
status in response to rtpg requests. These requests get
retried for a maximum of 60 seconds by default before timing
out. Sometimes this timeout isn't sufficient to allow the
array to complete the transition. T10-spc4 addresses this
under 'Report Target Port Groups' command.
This update retrieves the timeout value from the storage
array if available and retries the transitioning rtpgs
for up to the 'implied transitioning timeout' value
Signed-off-by: Rob Evers <revers@redhat.com>
Reviewed-by: Babu Moger <babu.moger@netapp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This has scsi_internal_device_unblock/scsi_target_unblock take
the new state to set the devices as an argument instead of
always setting to running. The patch also converts users of these
functions.
This allows the FC and iSCSI class to transition devices from blocked
to transport-offline, so that when fast_io_fail/replacement_timeout
has fired we do not set the devices back to running. Instead, we
set them to SDEV_TRANSPORT_OFFLINE.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch adds a new state SDEV_TRANSPORT_OFFLINE. It will
be used by transport classes to offline devices for cases like
when the fast_io_fail/recovery_tmo fires. In those cases we
want all IO to fail, and we have not yet escalated to dev_loss_tmo
behavior where we are removing the devices.
Currently to handle this state, transport classes are setting
the scsi_device's state to running, setting their internal
session/port structs state to something that indicates failed,
and then failing IO from some transport check in the queuecommand.
The reason for the new value is so that users can distinguish
between a device failure that is a result of a transport problem
vs the wide range of errors that devices get offlined for
when a scsi command times out and we offline the devices there.
It also fixes the confusion as to why the transport class is
failing IO, but has set the device state from blocked to running.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Updates newly added stats from fc_get_host_stats,
added new function fc_exch_update_stats to
update exches related stats from fc_exch.c
by going thru internal ema_list elements.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Acked-by : Robert Love <robert.w.love@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Adds stats to track FCP pkt and frame alloc
failure.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Acked-by : Robert Love <robert.w.love@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The libfc is used by fcoe but fcoe agnostic,
and therefore should not have any fcoe references.
So renaming fcoe_dev_stats from libfc as its for fc_stats.
After that libfc is fcoe string free except some strings for
Open-FCoE.org.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Acked-by : Robert Love <robert.w.love@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Acked-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The libfc provides more flexibility and with that
we can monitor some more FC specific stats for
FC exches or FCP error cases, this patch add
such new FC stats.
The patch adds *only* FC specific new stats to
existing fc_host attribute container.
Added stats names are self explanatory as
existing FC stats already has, however anyway
still added commentary along their definition
to describe them.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Acked-by : Robert Love <robert.w.love@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
fill_result_tf() grabs the taskfile flags from the originating qc which
sas_ata_qc_fill_rtf() promptly overwrites. The presence of an
ata_taskfile in the sata_device makes it tempting to just copy the full
contents in sas_ata_qc_fill_rtf(). However, libata really only wants
the fis contents and expects the other portions of the taskfile to not
be touched by ->qc_fill_rtf. To that end store a fis buffer in the
sata_device and use ata_tf_from_fis() like every other ->qc_fill_rtf()
implementation.
Cc: <stable@vger.kernel.org>
Reported-by: Praveen Murali <pmurali@logicube.com>
Tested-by: Praveen Murali <pmurali@logicube.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If ATA device supports "Device Attention", then tell scsi layer that
the device supports runtime power off.
Signed-off-by: Aaron Lu <aaron.lu@amd.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
For being able to bind ata devices against acpi devices, scsi_bus_type
needs to be set as bus in struct acpi_bus_type. So add wrapper to
scsi_lib to accomplish that.
Signed-off-by: Holger Macht <holger@homac.de>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Several bug reports have been received recently for USB mass-storage
devices that don't handle READ CAPACITY(16) commands properly. They
report bogus sizes, in some cases becoming unusable as a result.
The bugs were triggered by commit
09b6b51b0b (SCSI & usb-storage: add
flags for VPD pages and REPORT LUNS), which caused usb-storage to stop
overriding the SCSI level reported by devices. By default, the sd
driver will try READ CAPACITY(16) first for any device whose level is
above SCSI_SPC_2.
It seems likely that any device large enough to require the use of
READ CAPACITY(16) (i.e., 2 TB or more) would be able to handle READ
CAPACITY(10) commands properly. Indeed, I don't know of any devices
that don't handle READ CAPACITY(10) properly.
Therefore this patch (as1559) adds a new flag telling the sd driver
to try READ CAPACITY(10) before READ CAPACITY(16), and sets this flag
for every USB mass-storage device. If a device really is larger than
2 TB, sd will fall back to READ CAPACITY(16) just as it used to.
This fixes Bugzilla #43391.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Hans de Goede <hdegoede@redhat.com>
CC: "James E.J. Bottomley" <JBottomley@parallels.com>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch has the SW FCoE driver and the bnx2fc
driver make use of the new fcoe_sysfs API added
earlier in this patch series.
After this patch a fcoe_ctlr_device is allocated with
private data in this order.
+------------------+ +------------------+
| fcoe_ctlr_device | | fcoe_ctlr_device |
+------------------+ +------------------+
| fcoe_ctlr | | fcoe_ctlr |
+------------------+ +------------------+
| fcoe_interface | | bnx2fc_interface |
+------------------+ +------------------+
libfcoe also takes part in this new model since it
discovers and manages fcoe_fcf instances. The memory
allocation is different for FCFs. I didn't want to
impact libfcoe's fcoe_fcf processing, so this patch
creates fcoe_fcf_device instances for each discovered
fcoe_fcf. The two are paired using a (void * priv)
member of the fcoe_ctlr_device. This allows libfcoe
to continue maintaining its list of fcoe_fcf instances
and simply attaches and detaches them from existing
or new fcoe_fcf_device instances.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch adds a 'fcoe bus' infrastructure to the kernel
that is driven by changes to libfcoe which allow LLDs to
present FIP (FCoE Initialization Protocol) discovered
entities and their attributes to user space via sysfs.
This patch adds the following APIs-
fcoe_ctlr_device_add
fcoe_ctlr_device_delete
fcoe_fcf_device_add
fcoe_fcf_device_delete
They allow the LLD to expose the FCoE ENode Controller
and any discovered FCFs (Fibre Channel Forwarders, e.g.
FCoE switches) to the user. Each of these new devices
has their own bus_type so that they are grouped together
for easy lookup from a user space application. Each
new class has an attribute_group to expose attributes
for any created instances. The attributes are-
fcoe_ctlr_device
* fcf_dev_loss_tmo
* lesb_link_fail
* lesb_vlink_fail
* lesb_miss_fka
* lesb_symb_err
* lesb_err_block
* lesb_fcs_error
fcoe_fcf_device
* fabric_name
* switch_name
* priority
* selected
* fc_map
* vfid
* mac
* fka_peroid
* fabric_state
* dev_loss_tmo
A device loss infrastructre similar to the FC Transport's
is also added by this patch. It is nice to have so that a
link flapping adapter doesn't continually advance the count
used to identify the discovered FCF. FCFs will exist in a
"Disconnected" state until either the timer expires or the
FCF is rediscovered and becomes "Connected."
This patch generates a few checkpatch.pl WARNINGS that
I'm not sure what to do about. They're macros modeled
around the FC Transport attribute building macros, which
have the same 'feature' where the caller can ommit a cast
in the argument list and no cast occurs in the code. I'm
not sure how to keep the code condensed while keeping the
macros. Any advice would be appreciated.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Currently the fcoe_ctlr associated with an interface is allocated
as a member of struct fcoe_interface. This causes problems when
attempting to use the new fcoe_sysfs APIs which allow us to allocate
the fcoe_interface as private data to the fcoe_ctlr_device instance.
The problem is that libfcoe wants to be able use pointer math to find a
fcoe_ctlr's fcoe_ctlr_device as well as finding a fcoe_ctlr_device's
assocated fcoe_ctlr. To do this we need to allocate the
fcoe_ctlr_device, with private data for the LLD. The private data
contains the fcoe_ctlr and its private data is the fcoe_interface.
This patch only allocates the fcoe_interface with the fcoe_ctlr, the
fcoe_ctlr_device will be added in a later patch, which will complete
the below diagram-
+------------------+
| fcoe_ctlr_device |
+------------------+
| fcoe_ctlr |
+------------------+
| fcoe_interface |
+------------------+
This prep work will allow us to go from a fcoe_ctlr_device instance
to its fcoe_ctlr as well as from a fcoe_ctlr to its fcoe_ctlr_device
once the fcoe_sysfs API is in use (later patches in this series).
Signed-off-by: Robert Love <robert.w.love@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
1/ Rework remote-node-context (RNC) handling for proper management of
the silicon state machine in error handling and hot-plug conditions.
Further details below, suffice to say if the RNC is mismanaged the
silicon state machines may lock up.
2/ Refactor the initialization code to be reused for suspend/resume support
3/ Miscellaneous bug fixes to address discovery issues and hardware
compatibility.
RNC rework details from Jeff Skirvin:
In the controller, devices as they appear on a SAS domain (or
direct-attached SATA devices) are represented by memory structures known
as "Remote Node Contexts" (RNCs). These structures are transferred from
main memory to the controller using a set of register commands; these
commands include setting up the context ("posting"), removing the
context ("invalidating"), and commands to control the scheduling of
commands and connections to that remote device ("suspensions" and
"resumptions"). There is a similar path to control RNC scheduling from
the protocol engine, which interprets the results of command and data
transmission and reception.
In general, the controller chooses among non-suspended RNCs to find one
that has work requiring scheduling the transmission of command and data
frames to a target. Likewise, when a target tries to return data back
to the initiator, the state of the RNC is used by the controller to
determine how to treat the incoming request. As an example, if the RNC
is in the state "TX/RX Suspended", incoming SSP connection requests from
the target will be rejected by the controller hardware. When an RNC is
"TX Suspended", it will not be selected by the controller hardware to
start outgoing command or data operations (with certain priority-based
exceptions).
As mentioned above, there are two sources for management of the RNC
states: commands from driver software, and the result of transmission
and reception conditions of commands and data signaled by the controller
hardware. As an example of the latter, if an outgoing SSP command ends
with a OPEN_REJECT(BAD_DESTINATION) status, the RNC state will
transition to the "TX Suspended" state, and this is signaled by the
controller hardware in the status to the completion of the pending
command as well as signaled in a controller hardware event. Examples of
the former are included in the patch changelogs.
Driver software is required to suspend the RNC in a "TX/RX Suspended"
condition before any outstanding commands can be terminated. Failure to
guarantee this can lead to a complete hardware hang condition. Earlier
versions of the driver software did not guarantee that an RNC was
correctly managed before I/O termination, and so operated in an unsafe
way.
Further, the driver performed unnecessary contortions to preserve the
remote device command state and so was more complicated than it needed
to be. A simplifying driver assumption is that once an I/O has entered
the error handler path without having completed in the target, the
requirement on the driver is that all use of the sas_task must end.
Beyond that, recovery of operation is dependent on libsas and other
components to reset, rediscover and reconfigure the device before normal
operation can restart. In the driver, this simplifying assumption meant
that the RNC management could be reduced to entry into the suspended
state, terminating the targeted I/O request, and resuming the RNC as
needed for device-specific management such as an SSP Abort Task or LUN
Reset Management request.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=HYvO
-----END PGP SIGNATURE-----
Merge tag 'isci-for-3.5' into misc
isci update for 3.5
1/ Rework remote-node-context (RNC) handling for proper management of
the silicon state machine in error handling and hot-plug conditions.
Further details below, suffice to say if the RNC is mismanaged the
silicon state machines may lock up.
2/ Refactor the initialization code to be reused for suspend/resume support
3/ Miscellaneous bug fixes to address discovery issues and hardware
compatibility.
RNC rework details from Jeff Skirvin:
In the controller, devices as they appear on a SAS domain (or
direct-attached SATA devices) are represented by memory structures known
as "Remote Node Contexts" (RNCs). These structures are transferred from
main memory to the controller using a set of register commands; these
commands include setting up the context ("posting"), removing the
context ("invalidating"), and commands to control the scheduling of
commands and connections to that remote device ("suspensions" and
"resumptions"). There is a similar path to control RNC scheduling from
the protocol engine, which interprets the results of command and data
transmission and reception.
In general, the controller chooses among non-suspended RNCs to find one
that has work requiring scheduling the transmission of command and data
frames to a target. Likewise, when a target tries to return data back
to the initiator, the state of the RNC is used by the controller to
determine how to treat the incoming request. As an example, if the RNC
is in the state "TX/RX Suspended", incoming SSP connection requests from
the target will be rejected by the controller hardware. When an RNC is
"TX Suspended", it will not be selected by the controller hardware to
start outgoing command or data operations (with certain priority-based
exceptions).
As mentioned above, there are two sources for management of the RNC
states: commands from driver software, and the result of transmission
and reception conditions of commands and data signaled by the controller
hardware. As an example of the latter, if an outgoing SSP command ends
with a OPEN_REJECT(BAD_DESTINATION) status, the RNC state will
transition to the "TX Suspended" state, and this is signaled by the
controller hardware in the status to the completion of the pending
command as well as signaled in a controller hardware event. Examples of
the former are included in the patch changelogs.
Driver software is required to suspend the RNC in a "TX/RX Suspended"
condition before any outstanding commands can be terminated. Failure to
guarantee this can lead to a complete hardware hang condition. Earlier
versions of the driver software did not guarantee that an RNC was
correctly managed before I/O termination, and so operated in an unsafe
way.
Further, the driver performed unnecessary contortions to preserve the
remote device command state and so was more complicated than it needed
to be. A simplifying driver assumption is that once an I/O has entered
the error handler path without having completed in the target, the
requirement on the driver is that all use of the sas_task must end.
Beyond that, recovery of operation is dependent on libsas and other
components to reset, rediscover and reconfigure the device before normal
operation can restart. In the driver, this simplifying assumption meant
that the RNC management could be reduced to entry into the suspended
state, terminating the targeted I/O request, and resuming the RNC as
needed for device-specific management such as an SSP Abort Task or LUN
Reset Management request.
Implement the ISCSI_HOST_PARAM_INITIATOR_NAME for .get_host_param
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This changes the ordering of initialization and probing events from:
1/ allocate rphy in PORTE_BYTES_DMAED, DISCE_REVALIDATE_DOMAIN
2/ allocate ata_port and schedule port probe in DISCE_PROBE
...to:
1/ allocate ata_port in PORTE_BYTES_DMAED, DISCE_REVALIDATE_DOMAIN
2/ allocate rphy in PORTE_BYTES_DMAED, DISCE_REVALIDATE_DOMAIN
3/ schedule port probe in DISCE_PROBE
This ordering prevents PHYE_SIGNAL_LOSS_EVENTS from sneaking in to
destrory ata devices before they have been fully initialized:
BUG: unable to handle kernel paging request at 0000000000003b10
IP: [<ffffffffa0053d7e>] sas_ata_end_eh+0x12/0x5e [libsas]
...
[<ffffffffa004d1af>] sas_unregister_common_dev+0x78/0xc9 [libsas]
[<ffffffffa004d4d4>] sas_unregister_dev+0x4f/0xad [libsas]
[<ffffffffa004d5b1>] sas_unregister_domain_devices+0x7f/0xbf [libsas]
[<ffffffffa004c487>] sas_deform_port+0x61/0x1b8 [libsas]
[<ffffffffa004bed0>] sas_phye_loss_of_signal+0x29/0x2b [libsas]
...and kills the awkward "sata domain_device briefly existing in the
domain without an ata_port" state.
Reported-by: Michal Kosciowski <michal.kosciowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When requeuing work to a draining workqueue the last work instance may
not be idle, so sas_queue_work() must not touch work->entry. Introduce
sas_work with a drain_node list_head to have a private list for
collecting work deferred due to drain collision.
Fixes reports like:
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<ffffffff810410d4>] process_one_work+0x2e/0x338
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Commit 18a4d0a22e ("[SCSI] Handle disk devices which can not process
medium access commands") introduced a bug in which we would attempt to
dereference the scsi driver even when the device had no ULD attached.
Ensure that a driver is registered and make the driver accessor function
more resilient to errors during device discovery.
Reported-by: Elric Fu <elricfu1@gmail.com>
Reported-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPdrIWAAoJEDeqqVYsXL0Mny4IAMTzXGOXCykpWhdIe2R8w0Ys
eIoTJhBKoQWnLTV8cOODtwmtZcoQLeXkZmizZiAJvX6O1tOgueg+W4AFa9grxXGI
O0d1bSb2ardzU7VZrZSY60Hd4bylMwn4Xv/0dRrQMwTJO0LEeGWsJPV2+2BuXwMB
lGCNB67oUBXgMOI1jUZQRwx/mBzQ3e/gINjnpZTNKHia7YkX/yVTFISq7htgfDN7
1wRGxymbHtVap3NbtUO96BUUndAiF5vom+4WNvaQUyPrCc6aoGWjv+J9DQXY/zgv
AYjujAluK396D6YncGFAWBzYOg9WFbq54v0PRUanjcTTAu5ILs2BxqWdhmnvl14=
=IH8T
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6
Pull SCSI updates from James Bottomley:
"This is primarily another round of driver updates (lpfc, bfa, fcoe,
ipr) plus a new ufshcd driver. There shouldn't be anything
controversial in here (The final deletion of scsi proc_ops which
caused some build breakage has been held over until the next merge
window to give us more time to stabilise it).
I'm afraid, with me moving continents at exactly the wrong time,
anything submitted after the merge window opened has been held over to
the next merge window."
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (63 commits)
[SCSI] ipr: Driver version 2.5.3
[SCSI] ipr: Increase alignment boundary of command blocks
[SCSI] ipr: Increase max concurrent oustanding commands
[SCSI] ipr: Remove unnecessary memory barriers
[SCSI] ipr: Remove unnecessary interrupt clearing on new adapters
[SCSI] ipr: Fix target id allocation re-use problem
[SCSI] atp870u, mpt2sas, qla4xxx use pci_dev->revision
[SCSI] fcoe: Drop the rtnl_mutex before calling fcoe_ctlr_link_up
[SCSI] bfa: Update the driver version to 3.0.23.0
[SCSI] bfa: BSG and User interface fixes.
[SCSI] bfa: Fix to avoid vport delete hang on request queue full scenario.
[SCSI] bfa: Move service parameter programming logic into firmware.
[SCSI] bfa: Revised Fabric Assigned Address(FAA) feature implementation.
[SCSI] bfa: Flash controller IOC pll init fixes.
[SCSI] bfa: Serialize the IOC hw semaphore unlock logic.
[SCSI] bfa: Modify ISR to process pending completions
[SCSI] bfa: Add fc host issue lip support
[SCSI] mpt2sas: remove extraneous sas_log_info messages
[SCSI] libfc: fcoe_transport_create fails in single-CPU environment
[SCSI] fcoe: reduce contention for fcoe_rx_list lock [v2]
...
Some switch implementations (eg., HP virtual connect FlexFabric) send two MAC
descriptors in FIP FLOGI response, with first MAC descriptor (granted_mac) used
as FPMA, and the second one (fcoe_mac) used as destination address for
sending/receiving FCoE packets. fip_mac continues to be used for FIP traffic.
This patch introduces fcoe_mac in fcoe_fcf structure. For regular switches,
both fcoe_mac and fip_mac will be the same. For the switches that send
additional MAC descriptor, fcoe_mac is updated.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
We don't need to pack 'struct iscsi_chap_rec' as buffer is built
locally in the driver and pass to the user-space.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Defined error codes for ping completion status.
This patch take care of Mike Christie's commets
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
"[RFC PATCH 0/2] audit of linux/device.h users in include/*"
https://lkml.org/lkml/2012/3/4/159
--
Nearly every subsystem has some kind of header with a proto like:
void foo(struct device *dev);
and yet there is no reason for most of these guys to care about the
sub fields within the device struct. This allows us to significantly
reduce the scope of headers including headers. For this instance, a
reduction of about 40% is achieved by replacing the include with the
simple fact that the device is some kind of a struct.
Unlike the much larger module.h cleanup, this one is simply two
commits. One to fix the implicit <linux/device.h> users, and then
one to delete the device.h includes from the linux/include/ dir
wherever possible.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=3j4+
-----END PGP SIGNATURE-----
Merge tag 'device-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
Pull <linux/device.h> avoidance patches from Paul Gortmaker:
"Nearly every subsystem has some kind of header with a proto like:
void foo(struct device *dev);
and yet there is no reason for most of these guys to care about the
sub fields within the device struct. This allows us to significantly
reduce the scope of headers including headers. For this instance, a
reduction of about 40% is achieved by replacing the include with the
simple fact that the device is some kind of a struct.
Unlike the much larger module.h cleanup, this one is simply two
commits. One to fix the implicit <linux/device.h> users, and then one
to delete the device.h includes from the linux/include/ dir wherever
possible."
* tag 'device-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
device.h: audit and cleanup users in main include dir
device.h: cleanup users outside of linux/include (C files)
"[RFC - PATCH 0/7] consolidation of BUG support code."
https://lkml.org/lkml/2012/1/26/525
--
The changes shown here are to unify linux's BUG support under
the one <linux/bug.h> file. Due to historical reasons, we have
some BUG code in bug.h and some in kernel.h -- i.e. the support for
BUILD_BUG in linux/kernel.h predates the addition of linux/bug.h,
but old code in kernel.h wasn't moved to bug.h at that time. As
a band-aid, kernel.h was including <asm/bug.h> to pseudo link them.
This has caused confusion[1] and general yuck/WTF[2] reactions.
Here is an example that violates the principle of least surprise:
CC lib/string.o
lib/string.c: In function 'strlcat':
lib/string.c:225:2: error: implicit declaration of function 'BUILD_BUG_ON'
make[2]: *** [lib/string.o] Error 1
$
$ grep linux/bug.h lib/string.c
#include <linux/bug.h>
$
We've included <linux/bug.h> for the BUG infrastructure and yet we
still get a compile fail! [We've not kernel.h for BUILD_BUG_ON.]
Ugh - very confusing for someone who is new to kernel development.
With the above in mind, the goals of this changeset are:
1) find and fix any include/*.h files that were relying on the
implicit presence of BUG code.
2) find and fix any C files that were consuming kernel.h and
hence relying on implicitly getting some/all BUG code.
3) Move the BUG related code living in kernel.h to <linux/bug.h>
4) remove the asm/bug.h from kernel.h to finally break the chain.
During development, the order was more like 3-4, build-test, 1-2.
But to ensure that git history for bisect doesn't get needless
build failures introduced, the commits have been reorderd to fix
the problem areas in advance.
[1] https://lkml.org/lkml/2012/1/3/90
[2] https://lkml.org/lkml/2012/1/17/414
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=PYQT
-----END PGP SIGNATURE-----
Merge tag 'bug-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
Pull <linux/bug.h> cleanup from Paul Gortmaker:
"The changes shown here are to unify linux's BUG support under the one
<linux/bug.h> file. Due to historical reasons, we have some BUG code
in bug.h and some in kernel.h -- i.e. the support for BUILD_BUG in
linux/kernel.h predates the addition of linux/bug.h, but old code in
kernel.h wasn't moved to bug.h at that time. As a band-aid, kernel.h
was including <asm/bug.h> to pseudo link them.
This has caused confusion[1] and general yuck/WTF[2] reactions. Here
is an example that violates the principle of least surprise:
CC lib/string.o
lib/string.c: In function 'strlcat':
lib/string.c:225:2: error: implicit declaration of function 'BUILD_BUG_ON'
make[2]: *** [lib/string.o] Error 1
$
$ grep linux/bug.h lib/string.c
#include <linux/bug.h>
$
We've included <linux/bug.h> for the BUG infrastructure and yet we
still get a compile fail! [We've not kernel.h for BUILD_BUG_ON.] Ugh -
very confusing for someone who is new to kernel development.
With the above in mind, the goals of this changeset are:
1) find and fix any include/*.h files that were relying on the
implicit presence of BUG code.
2) find and fix any C files that were consuming kernel.h and hence
relying on implicitly getting some/all BUG code.
3) Move the BUG related code living in kernel.h to <linux/bug.h>
4) remove the asm/bug.h from kernel.h to finally break the chain.
During development, the order was more like 3-4, build-test, 1-2. But
to ensure that git history for bisect doesn't get needless build
failures introduced, the commits have been reorderd to fix the problem
areas in advance.
[1] https://lkml.org/lkml/2012/1/3/90
[2] https://lkml.org/lkml/2012/1/17/414"
Fix up conflicts (new radeon file, reiserfs header cleanups) as per Paul
and linux-next.
* tag 'bug-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
kernel.h: doesn't explicitly use bug.h, so don't include it.
bug: consolidate BUILD_BUG_ON with other bug code
BUG: headers with BUG/BUG_ON etc. need linux/bug.h
bug.h: add include of it to various implicit C users
lib: fix implicit users of kernel.h for TAINT_WARN
spinlock: macroize assert_spin_locked to avoid bug.h dependency
x86: relocate get/set debugreg fcns to include/asm/debugreg.
This addresses some header check warnings. DRM headers which include
"drm.h" have been excluded, as they indirectly include types.h.
Signed-off-by: Bobby Powers <bobbypowers@gmail.com>
Cc: Chris Ball <cjb@laptop.org>
Cc: Dave Airlie <airlied@linux.ie>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPZxSnAAoJEDeqqVYsXL0M0Y4IAMX0vrTVZbg6psA5/gMcWGRP
CkFXEQ8n0PL2SCaj6BoDqamJFe5Nc7dnqxM0fGawB4S9vr3rHhiOlwO+NbV9zFYC
2skBTpeL3sjgtN/jTBdfeeAa7xTYpu/XGyei0NS1A5c2AyMVXV0uYV2s4VNZxe44
tVIn1OEzM2giZ9EB1OZslDMrg5XXm3MBIUECP0LbWUhBm/35caSFKzMXRwhh7WiK
+AVmc2AZYtdEwuknDyiH7KlsaoB3vGL9pPrAUJzIgEhy2pOo2A7W72HfA4Fj+y6a
uF9HBS5zciMp1+sGWry62AjNbWgin9BRlozBEO/lJhIfMGDV1nXEIJsOkOgkdoE=
=1TxB
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6
SCSI updates from James Bottomley:
"The update includes the usual assortment of driver updates (lpfc,
qla2xxx, qla4xxx, bfa, bnx2fc, bnx2i, isci, fcoe, hpsa) plus a huge
amount of infrastructure work in the SAS library and transport class
as well as an iSCSI update. There's also a new SCSI based virtio
driver."
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (177 commits)
[SCSI] qla4xxx: Update driver version to 5.02.00-k15
[SCSI] qla4xxx: trivial cleanup
[SCSI] qla4xxx: Fix sparse warning
[SCSI] qla4xxx: Add support for multiple session per host.
[SCSI] qla4xxx: Export CHAP index as sysfs attribute
[SCSI] scsi_transport: Export CHAP index as sysfs attribute
[SCSI] qla4xxx: Add support to display CHAP list and delete CHAP entry
[SCSI] iscsi_transport: Add support to display CHAP list and delete CHAP entry
[SCSI] pm8001: fix endian issue with code optimization.
[SCSI] pm8001: Fix possible racing condition.
[SCSI] pm8001: Fix bogus interrupt state flag issue.
[SCSI] ipr: update PCI ID definitions for new adapters
[SCSI] qla2xxx: handle default case in qla2x00_request_firmware()
[SCSI] isci: improvements in driver unloading routine
[SCSI] isci: improve phy event warnings
[SCSI] isci: debug, provide state-enum-to-string conversions
[SCSI] scsi_transport_sas: 'enable' phys on reset
[SCSI] libsas: don't recover end devices attached to disabled phys
[SCSI] libsas: fixup target_port_protocols for expanders that don't report sata
[SCSI] libsas: set attached device type and target protocols for local phys
...
Pull SCSI target updates from Nicholas Bellinger:
"This contains the usual set of updates and bugfixes to target-core +
existing fabric module code, along with a handful of the patches
destined for v3.3 stable.
It also contains the necessary target-core infrastructure pieces
required to run using tcm_qla2xxx.ko WWPNs with the new Qlogic Fibre
Channel fabric module currently queued in target-pending/for-next-merge,
and coming for round 2.
The highlights for this series include:
- Add target_submit_tmr() helper function for fabric task management
(andy)
- Convert tcm_fc to use target_submit_tmr() (andy)
- Replace target core various cmd flags with a transport state (hch)
- Convert loopback to use workqueue submission (hch)
- Convert target core to use array_zalloc for tpg_lun_list (joern)
- Convert target core to use array_zalloc for device_list (joern)
- Add target core support for TMR_ABORT_TASK (nab)
- Add target core se_sess->sess_kref + get/put helpers (nab)
- Add target core se_node_acl->acl_kref for ->acl_free_comp usage
(nab)
- Convert iscsi-target to use target_put_session + sess_kref (nab)
- Fix tcm_fc fc_exch memory leak in ft_send_resp_status (nab)
- Fix ib_srpt srpt_handle_cmd send_ioctx->ioctx_kref leak on
exception (nab)
- Fix target core up handling of short INQUIRY buffers (roland)
- Untangle target-core front-end and back-end meanings of max_sectors
attribute (roland)
- Set loopback residual field for SCSI commands (roland)
- Fix target-core 16-bit target ports for SET TARGET PORT GROUPS
emulation (roland)
Thanks again to Andy, Christoph, Joern, Roland, and everyone who has
contributed this round!"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (64 commits)
ib_srpt: Fix srpt_handle_cmd send_ioctx->ioctx_kref leak on exception
loopback: Fix transport_generic_allocate_tasks error handling
iscsi-target: remove improper externs
iscsi-target: Remove unused variables in iscsi_target_parameters.c
target: remove obvious warnings
target: Use array_zalloc for device_list
target: Use array_zalloc for tpg_lun_list
target: Fix sense code for unsupported SERVICE ACTION IN
target: Remove hack to make READ CAPACITY(10) lie if thin provisioning is enabled
target: Bump core version to v4.1.0-rc2-ml + fabric versions
tcm_fc: Fix fc_exch memory leak in ft_send_resp_status
target: Drop unused legacy target_core_fabric_ops API callers
iscsi-target: Convert to use target_put_session + sess_kref
target: Convert se_node_acl->acl_group removal to use ->acl_kref
target: Add se_node_acl->acl_kref for ->acl_free_comp usage
target: Add se_node_acl->acl_free_comp for NodeACL release path
target: Add se_sess->sess_kref + get/put helpers
target: Convert session_lock to irqsave
target: Fix typo in drivers/target
iscsi-target: Fix dynamic -> explict NodeACL pointer reference
...
The <linux/device.h> header includes a lot of stuff, and
it in turn gets a lot of use just for the basic "struct device"
which appears so often.
Clean up the users as follows:
1) For those headers only needing "struct device" as a pointer
in fcn args, replace the include with exactly that.
2) For headers not really using anything from device.h, simply
delete the include altogether.
3) For headers relying on getting device.h implicitly before
being included themselves, now explicitly include device.h
4) For files in which doing #1 or #2 uncovers an implicit
dependency on some other header, fix by explicitly adding
the required header(s).
Any C files that were implicitly relying on device.h to be
present have already been dealt with in advance.
Total removals from #1 and #2: 51. Total additions coming
from #3: 9. Total other implicit dependencies from #4: 7.
As of 3.3-rc1, there were 110, so a net removal of 42 gives
about a 38% reduction in device.h presence in include/*
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
If a header file is making use of BUG, BUG_ON, BUILD_BUG_ON, or any
other BUG variant in a static inline (i.e. not in a #define) then
that header really should be including <linux/bug.h> and not just
expecting it to be implicitly present.
We can make this change risk-free, since if the files using these
headers didn't have exposure to linux/bug.h already, they would have
been causing compile failures/warnings.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
For offload iSCSI like qla4xxx CHAP entries are stored in FLASH.
This patch adds support to list CHAP entries stored in FLASH and
delete specified CHAP entry from FLASH using iscsi tools.
Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
libata issues follow up srsts when the controller has a hard time
recording the signature-fis after a reset, or if the link supports port
multipliers. libsas does not support port multipliers and no current
libsas lldds appear to need help retrieving the signature fis. Revert
it for now to remove confusion.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
libsas ata error handling is already async but this does not help the
scan case. Move initial link recovery out from under host->scan_mutex,
and delay synchronization with eh until after all port probe/recovery
work has been queued.
Device ordering is maintained with scan order by still calling
sas_rphy_add() in order of domain discovery.
Since we now scan the domain list when invoking libata-eh we need to be
careful to check for fully initialized ata ports.
Acked-by: Jack Wang <jack_wang@usish.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
ata devices are always scanned after ssp. Prior to the ata error
handling reworks libsas would tend to scan devices in ascending expander
phy order. Restore this ordering by deferring ssp discovery to a
DISCE_PROBE event, and keep the probe order consistent with the
discovery order, not the placement of sata devices.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
libsas fails to discover all sata devices in the domain. If a device fails
negotiation and does not transmit a signature fis the link needs recovery.
libata already understands how to manage slow to come up links, so treat these
conditions as ata device attach events for the purposes of creating an
ata_port. This allows libata to manage retrying link bring up.
Rediscovery is modified to be careful about checking changes in dev_type. It
looks like libsas leaks old devices if the sas address changes, but that's a
fix for another patch.
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If we have a domain with sas and sata devices there may still be sas
recovery actions to take after peeling off the commands to send to
libata.
Reported-by: Andrzej Jakowski <andrzej.jakowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If the top level expander is hot removed, mark all child devices as gone
before unregistration to short circuit futile recovery.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In the direct-attached case this routine returns the phy on which this
device was first discovered. Which is broken if we want to support
wide-targets, as this phy reference can become stale even though the
port is still active.
In the expander-attached case this routine tries to lookup the phy by
scanning the attached sas addresses of the parent expander, and BUG_ONs
if it can't find it. However since eh and the libsas workqueue run
independently we can still be attempting device recovery via eh after
libsas has recorded the device as detached. This is even easier to hit
now that eh is blocked while device domain rediscovery takes place, and
that libata is fed more timed out commands increasing the chances that
it will try to recover the ata device.
Arrange for dev->phy to always point to a last known good phy, it may be
stale after the port is torn down, but it will catch up for wide port
reconfigurations, and never be NULL.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Use ata_wait_after_reset() to poll for link recovery after a reset.
This combined with sas_ha->eh_mutex prevents expander rediscovery from
probing phys in an intermediate state. Local discovery does not have a
mechanism to filter link status changes during this timeout, so it
remains the responsibility of lldds to prevent premature port teardown.
Although once all lldd's support ->lldd_ata_check_ready() that could be
used as a gate to local port teardown.
The signature fis is re-transmitted when the link comes back so we
should be revalidating the ata device class, but that is left to a future
patch.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This allows us to use scsilun_to_int without an ugly cast.
Fix up places that use scsilun_to_int on fcp->fc_lun accordingly.
In fc target, this leaves ft_cmd.lun unused, so remove it.
Signed-off-by: Andy Grover <agrover@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Kiran Patil <kiran.patil@intel.com>
Cc: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
It's in SBC-3.
Signed-off-by: Andy Grover <agrover@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
SAS does not tag SMP requests, and at least one lldd (isci) does not permit
more than one in-flight request at a time.
[jejb: fix sas_init_dev tab issues while we're at it]
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Execute the link-reset triggered by sas_phy_enable via
transport_sas_phy_reset so that it can be managed by libata.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Link resets leave ata affiliations intact, so arrange for libsas to make
an effort to avoid dropping the device due to a slow-to-recover link.
Towards this end carry out reset in the host workqueue so that it can
check for ata devices and kick the reset request to libata. Hard
resets, in contrast, bypass libata since they are meant for associating
an ata device with another initiator in the domain (tears down
affiliations).
Need to add a new transport_sas_phy_reset() since the current
sas_phy_reset() is a utility function to libsas lldds. They are not
prepared for it to loop back into eh.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Extend the sas transport class to allow transport users to attach extra
data to a sas_phy (->hostdata). Use this area in libsas to move resets
to workq context in preparation for scheduling ata device resets through
libata-eh.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Since sata devices can take several seconds to recover the link on reset
the 0.5 seconds that libsas currently waits may not be enough. Instead
if we are rediscovering a phy that was previously attached to a sata
device let libata handle any resets to encourage the device to transmit
the initial fis.
Once sas_ata_hard_reset() and lldds learn how to honor 'deadline' libsas
should stop encountering phys in an intermediate state, until then this
will loop until the fis is transmitted or ->attached_sas_addr gets
cleared, but in the more likely initial discovery case we keep existing
behavior.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
libsas-eh if it successfully aborts an ata command will hide the timeout
condition (AC_ERR_TIMEOUT) from libata. The command likely completes
with the all-zero task->task_status it started with. Instead, interpret
a TMF_RESP_FUNC_COMPLETE as the end of the sas_task but keep the scmd
around for libata-eh to handle.
Tested-by: Andrzej Jakowski <andrzej.jakowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Until we have told the lldd to forget a task a timed out operation can
return from the hardware at any time. Since completion frees the task
we need to make sure that no tasks run their normal completion handler
once eh has decided to manage the task. Similar to
ata_scsi_cmd_error_handler() freeze completions to let eh judge the
outcome of the race.
Task collector mode is problematic because it presents a situation where
a task can be timed out and aborted before the lldd has even seen it.
For this case we need to guarantee that a task that an lldd has been
told to forget does not get queued after the lldd says "never seen it".
With sas_scsi_timed_out we achieve this with the ->task_queue_flush
mutex, rather than adding more time.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
We invoke task->task_done() to free the task in the eh case, but at this
point we are prepared for scsi_eh_flush_done_q() to finish off the scmd.
Introduce sas_end_task() to capture the final response status from the
lldd and free the task.
Also take the opportunity to kill this warning.
drivers/scsi/libsas/sas_scsi_host.c: In function ‘sas_end_task’:
drivers/scsi/libsas/sas_scsi_host.c:102:3: warning: case value ‘2’ not in enumerated type ‘enum exec_status’ [-Wswitch]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Since sas_ata does not implement ->freeze(), completions for scmds and
internal commands can still arrive concurrent with
ata_scsi_cmd_error_handler() and sas_ata_post_internal() respectively.
By the time either of those is called libata has committed to completing
the qc, and the ATA_PFLAG_FROZEN flag tells sas_ata_task_done() it has
lost the race.
In the sas_ata_post_internal() case we take on the additional
responsibility of freeing the sas_task to close the race with
sas_ata_task_done() freeing the the task while sas_ata_post_internal()
is in the process of invoking ->lldd_abort_task().
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
sas_discover_sata() notifies lldds of sata devices twice. Once to allow
the 'identify' to be sent, and a second time to allow aic94xx (the only
libsas driver that cares about sata_dev.identify) to setup NCQ
parameters before the device becomes known to the midlayer. Replace
this double notification and intervening 'identify' with an explicit
->lldd_ata_set_dmamode notification. With this change all ata internal
commands are issued by libata, so we no longer need sas_issue_ata_cmd().
The data from the identify command only needs to be cached in one
location so ata_device.id replaces domain_device.sata_dev.identify.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
libata error handling provides for a timeout for link recovery. libsas
must not rescan for previously known devices in this interval otherwise
it may remove a device that is simply waiting for its link to recover.
Let libata-eh make the determination of when the link is stable and
prevent libsas (host workqueue) from taking action while this
determination is pending.
Using a mutex (ha->disco_mutex) to flush and disable revalidation while
eh is running requires any discovery action that may block on eh be
moved to its own context outside the lock. Probing ATA devices
explicitly waits on ata-eh and the cache-flush-io issued during device
removal may also pend awaiting eh completion. Essentially any rphy
add/remove activity needs to run outside the lock.
This adds two new cleanup states for sas_unregister_domain_devices()
'allocated-but-not-probed', and 'flagged-for-destruction'. In the
'allocated-but-not-probed' state dev->rphy points to a rphy that is
known to have not been through a sas_rphy_add() event. At domain
teardown check if this device is still pending probe and cleanup
accordingly. Similarly if a device has already been queued for removal
then sas_unregister_domain_devices has nothing to do.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In preparation for adding tracking of another device state "destroy".
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When an lldd invokes ->notify_port_event() it can trigger a chain of libsas
events to:
1/ form the port and find the direct attached device
2/ if the attached device is an expander perform domain discovery
A call to flush_workqueue() will only flush the initial port formation work.
Currently libsas users need to call scsi_flush_work() up to the max depth of
chain (which will grow from 2 to 3 when ata discovery is moved to its own
discovery event). Instead of open coding multiple calls switch to use
drain_workqueue() to flush sas work.
drain_workqueue() does not handle new work submitted during the drain so
libsas needs a bit of infrastructure to hold off unchained work submissions
while a drain is in flight. A lldd ->notify() event is considered 'unchained'
while a sas_discover_event() is 'chained'. As Tejun notes:
"For now, I think it would be best to add private wrapper in libsas to
support deferring unchained work items while draining."
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In preparation for adding new states (SAS_HA_DRAINING, SAS_HA_FROZEN),
convert ha->state into a set of flags.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The locks only served to make sure the pending event bitmask was updated
consistently.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
These are never freed in the nominal path. A domain_device has a
different lifetime than a sas_rphy we need a dev->rphy independent way
of identifying sata devices.
Reviewed-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Arrange for the deallocation of a struct domain_device object when it no
longer has:
1/ any children
2/ references by any scsi_targets
3/ references by a lldd
The comment about domain_device lifetime in
Documentation/scsi/libsas.txt is stale as it appears mainline never had
a version of a struct domain_device that was registered as a kobject.
We now manage domain_device reference counts on behalf of external
agents.
Reviewed-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Per commit 3e4ec344 "libata: kill ATA_FLAG_DISABLED" needing to set
ATA_DEV_NONE is a holdover from before libsas converted to the
"new-style" ata-eh.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Commit 1e34c838 "[SCSI] libsas: remove spurious sata control register
read/write" removed the routines to fake the presence of the sata
control registers, now remove the unused data structure fields to kill
any remaining confusion.
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
We have experienced several devices which fail in a fashion we do not
currently handle gracefully in SCSI. After a failure these devices will
respond to the SCSI primary command set (INQUIRY, TEST UNIT READY, etc.)
but any command accessing the storage medium will time out.
The following patch adds an callback that can be used by upper level
drivers to inspect the results of an error handling command. This in
turn has been used to implement additional checking in the SCSI disk
driver.
If a medium access command fails twice but TEST UNIT READY succeeds both
times in the subsequent error handling we will offline the device. The
maximum number of failed commands required to take a device offline can
be tweaked in sysfs.
Also add a new error flag to scsi_debug which allows this scenario to be
easily reproduced.
[jejb: fix up integer parsing to use kstrtouint]
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Added ping support for iscsi adapter, application can use this
interface for diagnostic network connection.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Added support to post kernel host event to application using
netlink interface.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Problem description from Xi Wang:
A large max_r2t could lead to integer overflow in subsequent call to
iscsi_tcp_r2tpool_alloc(), allocating a smaller buffer than expected
and leading to out-of-bounds write.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Resubmitting as my previous post had format issues and did not go llinux-scsi.
This patch changes the function to set_msg_byte, set_host_byte and
set_driver_byte to correctly set the corresponding bytes appropriately.
It will reset the original setting and correctly set it to the new value. The
previous OR operation does not always set it back to new value. Look at patch
2/2 for an example.
Signed-off-by: Babu Moger <babu.moger@netapp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch adds support for Fabric Device Management
Interface as per FC-GS-4 spec. in libfc. Any driver
making use of libfc can enable fdmi state machine
for a given lport.
If lport has enabled FDMI support the lport state
machine will transition into FDMI after completing
the DNS states and before entering the SCR state.
The FDMI state transition is such that if there is an
error, it won't stop the lport state machine from
transitioning and the it will behave as if there was
no FDMI support.
The FDMI HBA attributes are registed with the Management
server via Register HBA (RHBA) command and the port
attributes are reigstered using the Register Port(RPA)
command.
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Acked-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Currently the libfc Common Transport(CT) calls assume that
the CT requests are Name Server specific only. This patch
makes it more flexible to allow more FC-GS services to make
use of these routines.
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Acked-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The values for the 4G and 10G speeds are not in sync with
definitions in SM-HBA/FC-GS-x/etc.
This patch brings them in sync to these specifications.
The values are converted to strings when represented via
sysfs attribute, hence that should cover for user space
apps as they may not see any change.
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Acked-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This adds FC-GS Fabric Device Management Interface
(FDMI) related attributes to fc_host_attr structure.
This is in preparation for allowing FDMI attributes
to be registered via libfc.
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Acked-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch (as1507) adds a skip_vpd_pages flag to struct scsi_device
and a no_report_luns flag to struct scsi_target. The first is used to
control whether sd will look at VPD pages for information on block
provisioning, limits, and characteristics. The second prevents
scsi_report_lun_scan() from issuing a REPORT LUNS command.
The patch also modifies usb-storage to set the new flag bits for all
USB devices and targets, and to stop adjusting the scsi_level value.
Historically we have seen that USB mass-storage devices often don't
support VPD pages or REPORT LUNS properly. Until now we have avoided
these things by setting the scsi_level to SCSI_2 for all USB devices.
But this has the side effect of storing the LUN bits into the second
byte of each CDB, and now we have a report of a device which doesn't
like that. The best solution is to stop abusing scsi_level and
instead have separate flags for VPD pages and REPORT LUNS.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Perry Wagle <wagle@mac.com>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1506) corrects a typo in the definition of the
scsi_target structure. pdt_1f_for_no_lun is supposed to be a
single-bit flag, not a full-sized integer.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Avoid that sparse complains about missing declarations for local
functions by declaring these static or by adding an #include directive.
Add the __percpu annotation where it is missing.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPBh1uAAoJEDeqqVYsXL0MnxIIAJl0SLxgX3Vo18jhv7epNaUy
Akm8VcLTjW99IAZm1x166pGjLvdeZJC5A50DxW3jQMknKYZyyxEmTGOOMVA/LuCS
J3V18tMrsEA7i1kEGx2MauRRNAvReAZl4a/nHuRc+hpVmfyQegBv1v4V0v0gzD5I
MDZSSksqtXpJhsHt2B4g/jao7RhuJYXw7NidRGzEtksax3NMyWzaIb/75Uq6eenE
HwJwCUgZZxxfRKksj/T8ShRE6BKL9wcvrm8SVNjBYF2OpnMUNCXtfLQ4fqbHtGz2
otWvoQxVERehPZhTWHk6QnLgPwBWYyIUK7ErSFMTb9EK8b3FsEZkw6/LlS/lXnI=
=Zopk
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6
SCSI updates for post 3.2 merge window
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (67 commits)
[SCSI] lpfc 8.3.28: Update driver version to 8.3.28
[SCSI] lpfc 8.3.28: Add Loopback support for SLI4 adapters
[SCSI] lpfc 8.3.28: Critical Miscellaneous fixes
[SCSI] Lpfc 8.3.28: FC and SCSI Discovery Fixes
[SCSI] lpfc 8.3.28: Add support for ABTS failure handling
[SCSI] lpfc 8.3.28: SLI fixes and added SLI4 support
[SCSI] lpfc 8.3.28: Miscellaneous fixes in sysfs and mgmt interfaces
[SCSI] mpt2sas: Removed redundant calling of _scsih_probe_devices() from _scsih_probe
[SCSI] mac_scsi: Remove obsolete IRQ_FLG_* users
[SCSI] qla4xxx: Update driver version to 5.02.00-k10
[SCSI] qla4xxx: check for FW alive before calling chip_reset
[SCSI] qla4xxx: Fix qla4xxx_dump_buffer to dump buffer correctly
[SCSI] qla4xxx: Fix the IDC locking mechanism
[SCSI] qla4xxx: Wait for disable_acb before doing set_acb
[SCSI] qla4xxx: Don't recover adapter if device state is FAILED
[SCSI] qla4xxx: fix call trace on rmmod with ql4xdontresethba=1
[SCSI] qla4xxx: Fix CPU lockups when ql4xdontresethba set
[SCSI] qla4xxx: Perform context resets in case of context failures.
[SCSI] iscsi class: export pid of process that created
[SCSI] mpt2sas: Remove unused duplicate diag_buffer_enable param
...
* 'upstream-linus' of git://github.com/jgarzik/libata-dev:
ahci: support the STA2X11 I/O Hub
pata_bf54x: fix BMIDE status register emulation
ata: add ata port hibernate callbacks
ata: update ata port's runtime status during system resume
[SCSI] runtime resume parent for child's system-resume
ahci: platform support for suspend/resume
libata-core: kill duplicate statement in ata_do_set_mode()
pata_of_platform: remove direct dependency on OF_IRQ
SATA/PATA: convert drivers/ata/* to use module_platform_driver()
pata_cs5536: forward port changes from cs5536
libata-sff: use ATAPI_{COD|IO}
ata: add ata port runtime PM callbacks
ata: add ata port system PM callbacks
[SCSI] sd: check runtime PM status in sd_shutdown
[SCSI] check runtime PM status in system PM
[SCSI] add flag to skip the runtime PM calls on the host
ata: make ata port as parent device of scsi host
ahci: start engine only during soft/hard resets
With previous change, now the ata port runtime suspend will happen as:
disk suspend --> scsi target suspend --> scsi host suspend --> ata port
suspend
ata port(parent device) suspend need to schedule scsi EH which will resume
scsi host(child device). Then the child device resume will in turn make
parent device resume first. This is kind of recursive.
This patch adds a new flag Scsi_Host::eh_noresume.
ata port will set this flag to skip the runtime PM calls on scsi host.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use DCB notifiers to set the skb priority to allow packets
to be steered and tagged correctly over DCB enabled drivers
that setup traffic classes.
This allows queue_mapping() routines to be removed in these
drivers that were previously inspecting the ethertype of
every skb to mark FCoE/FIP frames.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
There could be multiple userspace entities creating/destroying/
recoverying sessions and also the kernel's iscsi drivers could
be doing this too. If the userspace apps do try to manage the kernel
ones it can get the driver/fw out of sync and cause the user to
loose the root disk, oopses or ping ponging becasue userspace
wants to do one thing but the kernel manager thought we
are trying to do another.
This patch fixes the problem by just exporting the pid of
the entity that created the session. Userspace programs like
iscsid, iscsiadm, iscsistart, qlogic's tools, etc, can then
figure out which sessions they own and only manage them.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
All the handlers have now implemented the match function so We don't need to
use scsi_dev_info any more for matching purposes.
Signed-off-by: Babu Moger <babu.moger@netapp.com>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This is finally the RAID5 Write support.
The bigger part of this patch is not the XOR engine itself, But the
read4write logic, which is a complete mini prepare_for_striping
reading engine that can read scattered pages of a stripe into cache
so it can be used for XOR calculation. That is, if the write was not
stripe aligned.
The main algorithm behind the XOR engine is the 2 dimensional array:
struct __stripe_pages_2d.
A drawing might save 1000 words
---
__stripe_pages_2d
|
n = pages_in_stripe_unit;
w = group_width - parity;
| pages array presented to the XOR lib
| |
V |
__1_page_stripe[0].pages --> [c0][c1]..[cw][c_par] <---|
| |
__1_page_stripe[1].pages --> [c0][c1]..[cw][c_par] <---
|
... | ...
|
__1_page_stripe[n].pages --> [c0][c1]..[cw][c_par]
^
|
data added columns first then row
---
The pages are put on this array columns first. .i.e:
p0-of-c0, p1-of-c0, ... pn-of-c0, p0-of-c1, ...
So we are doing a corner turn of the pages.
Note that pages will zigzag down and left. but are put sequentially
in growing order. So when the time comes to XOR the stripe, only the
beginning and end of the array need be checked. We scan the array
and any NULL spot will be field by pages-to-be-read.
The FS that wants to support RAID5 needs to supply an
operations-vector that searches a given page in cache, and specifies
if the page is uptodate or need reading. All these pages to be read
are put on a slave ore_io_state and synchronously read. All the pages
of a stripe are read in one IO, using the scatter gather mechanism.
In write we constrain our IO to only be incomplete on a single
stripe. Meaning either the complete IO is within a single stripe so
we might have pages to read from both beginning or end of the
strip. Or we have some reading to do at beginning but end at strip
boundary. The left over pages are pushed to the next IO by the API
already established by previous work, where an IO offset/length
combination presented to the ORE might get the length truncated and
the user must re-submit the leftover pages. (Both exofs and NFS
support this)
But any ORE user should make it's best effort to align it's IO
before hand and avoid complications. A cached ore_layout->stripe_size
member can be used for that calculation. (NOTE: that ORE demands
that stripe_size may not be bigger then 32bit)
What else? Well read it and tell me.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
This patch introduces the first stage of RAID5 support
mainly the skip-over-raid-units when reading. For
writes it inserts BLANK units, into where XOR blocks
should be calculated and written to.
It introduces the new "general raid maths", and the main
additional parameters and components needed for raid5.
Since at this stage it could corrupt future version that
actually do support raid5. The enablement of raid5
mounting and setting of parity-count > 0 is disabled. So
the raid5 code will never be used. Mounting of raid5 is
only enabled later once the basic XOR write is also in.
But if the patch "enable RAID5" is applied this code has
been tested to be able to properly read raid5 volumes
and is according to standard.
Also it has been tested that the new maths still properly
supports RAID0 and grouping code just as before.
(BTW: I have found more bugs in the pnfs-obj RAID math
fixed here)
The ore.c file is getting too big, so new ore_raid.[hc]
files are added that will include the special raid stuff
that are not used in striping and mirrors. In future write
support these will get bigger.
When adding the ore_raid.c to Kbuild file I was forced to
rename ore.ko to libore.ko. Is it possible to keep source
file, say ore.c and module file ore.ko the same even if there
are multiple files inside ore.ko?
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Userspace was sending the priority/id part of the vlan tag
and sysfs was displaying the id in the vlan file. This
renames the vlan sysfs file to vlan_id to reflect that it
was showing the id and to match the vlan_priority file.
This also adds a ISCSI_NET_PARAM_VLAN_TAG iscsi nl command
to relfect that we are sending down the vlan/priority
part of the tag.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This has the driver use helpers for a common operation and fixes
a issue where if multiple iscsi params are sent they could be
sent at offsets that cause unaligned accesses. The nla helpers
account for the padding needed to align properly for the driver.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Replaced the iscsi_get_next_target_id with IDA to make
target-id allocation efficient for iscsi offload drivers
This patch should be applied after Jonathen Cameron Patch
"ida : simplified functions for id allocation"
Signed-off-by: John Soni Jose <jose0here@gmail.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
port->dev_list maintains a list of devices attached to a given sas root port.
It needs to be mutated under a lock as contexts outside of the
single-threaded-libsas-workqueue access the list via sas_find_dev_by_rphy().
Fixup locations where the list was being mutated without a lock.
This is a follow-up to commit 5911e963 "[SCSI] libsas: remove expander
from dev list on error", where Luben noted [1]:
> 2/ We have unlocked list manipulations in sas_ex_discover_end_dev(),
> sas_unregister_common_dev(), and sas_ex_discover_end_dev()
Yes, I can see that and that is very unfortunate.
[1]: http://marc.info/?l=linux-scsi&m=131480962006471&w=2
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Except for obtaining the netdev from lport, fcoe_get_lesb is the common code
for the LLDs.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Acked-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Current ore_check_io API receives a residual
pointer, to report partial IO. But it is actually
not used, because in a multiple devices IO there
is never a linearity in the IO failure.
On the other hand if every failing device is reported
through a received callback measures can be taken to
handle only failed devices. One at a time.
This will also be needed by the objects-layout-driver
for it's error reporting facility.
Exofs is not currently using the new information and
keeps the old behaviour of failing the complete IO in
case of an error. (No partial completion)
TODO: Use an ore_check_io callback to set_page_error only
the failing pages. And re-dirty write pages.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
All users of the ore will need to check if current code
supports the given layout. For example RAID5/6 is not
currently supported.
So move all the checks from exofs/super.c to a new
ore_verify_layout() to be used by ore users.
Note that any new layout should be passed through the
ore_verify_layout() because the ore engine will prepare
and verify some internal members of ore_layout, and
assumes it's called.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Users like the objlayout-driver would like to only pass
a partial device table that covers the IO in question.
For example exofs divides the file into raid-group-sized
chunks and only serves group_width number of devices at
a time.
The partiality is communicated by setting
ore_componets->first_dev and the array covers all logical
devices from oc->first_dev upto (oc->first_dev + oc->numdevs)
The ore_comp_dev() API receives a logical device index
and returns the actual present device in the table.
An out-of-range dev_index will BUG.
Logical device index is the theoretical device index as if
all the devices of a file are present. .i.e:
total_devs = group_width * mirror_p1 * group_count
0 <= dev_index < total_devs
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Now that each ore_io_state covers only a single raid group.
A single striping_info math is needed. Embed one inside
ore_io_state to cache the calculation results and eliminate
an extra call.
Also the outer _prepare_for_striping is removed since it does nothing.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
In the pNFS obj-LD the device table at the layout level needs
to point to a device_cache node, where it is possible and likely
that many layouts will point to the same device-nodes.
In Exofs we have a more orderly structure where we have a single
array of devices that repeats twice for a round-robin view of the
device table
This patch moves to a model that can be used by the pNFS obj-LD
where struct ore_components holds an array of ore_dev-pointers.
(ore_dev is newly defined and contains a struct osd_dev *od
member)
Each pointer in the array of pointers will point to a bigger
user-defined dev_struct. That can be accessed by use of the
container_of macro.
In Exofs an __alloc_dev_table() function allocates the
ore_dev-pointers array as well as an exofs_dev array, in one
allocation and does the addresses dance to set everything pointing
correctly. It still keeps the double allocation trick for the
inodes round-robin view of the table.
The device table is always allocated dynamically, also for the
single device case. So it is unconditionally freed at umount.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
The struct ore_striping_info will be used later in other
structures. And ore_calc_stripe_info as well. Rename them
make struct ore_striping_info public. ore_calc_stripe_info
is still static, will be made public on first use.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
The struct pnfs_osd_data_map data_map member of exofs_sb_info was
never used after mount. In fact all it's members were duplicated
by the ore_layout structure. So just remove the duplicated information.
Also removed some stupid, but perfectly supported, restrictions on
layout parameters. The case where num_devices is not divisible by
mirror_count+1 is perfectly fine since the rotating device view
will eventually use all the devices it can get.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Benny Halevy <bhalevy@tonian.com>
ore_components already has a comps member so this leads
to things like comps->comps which is annoying. the name oc
was already used in new code. So rename all old usage of
ore_components comps => ore_components oc.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Allow the sas-transport-class to update events for local phys via a new
PHY_FUNC_GET_EVENTS command to ->lldd_control_phy(). Fixup drivers that
are not prepared for new enum phy_func values, and unify
->lldd_control_phy() error codes.
These are the SAS defined phy events that are reported in a
smp-report-phy-error-log command:
* /sys/class/sas_phy/<phyX>/invalid_dword_count
* /sys/class/sas_phy/<phyX>/running_disparity_error_count
* /sys/class/sas_phy/<phyX>/loss_of_dword_sync_count
* /sys/class/sas_phy/<phyX>/phy_reset_problem_count
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Based on original implementation from Jiangbi Liu and Maciej Trela.
ATAPI transfers happen in two-to-three stages. The two stage atapi
commands are those that include a dma data transfer. The data transfer
portion of these operations is handled by the hardware packet-dma
acceleration. The three-stage commands do not have a data transfer and
are handled without hardware assistance in raw frame mode.
stage1: transmit host-to-device fis to notify the device of an incoming
atapi cdb. Upon reception of the pio-setup-fis repost the task_context
to perform the dma transfer of the cdb+data (go to stage3), or repost
the task_context to transmit the cdb as a raw frame (go to stage 2).
stage2: wait for hardware notification of the cdb transmission and then
go to stage 3.
stage3: wait for the arrival of the terminating device-to-host fis and
terminate the command.
To keep the implementation simple we only support ATAPI packet-dma
protocol (for commands with data) to avoid needing to handle the data
transfer manually (like we do for SATA-PIO). This may affect
compatibility for a small number of devices (see
ATA_HORKAGE_ATAPI_MOD16_DMA).
If the data-transfer underruns, or encounters an error the
device-to-host fis is expected to arrive in the unsolicited frame queue
to pass to libata for disposition. However, in the DONE_UNEXP_FIS (data
underrun) case it appears we need to craft a response. In the
DONE_REG_ERR case we do receive the UF and propagate it to libsas.
Signed-off-by: Maciej Trela <maciej.trela@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
cache aligned xid and ex_lock beside
removing holes.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Re-arrange its fields to avoid padding and have better
cacheline alignments.
Removed not used start_time, end_time and last_pkt_time
fields.
This all reduced this struct size to 448 from 480 and
that also reduced one cacheline on x86_64 beside
eliminating 8 pads. However kept logical fields together.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Several sas drivers legitimately check the protocol against the union of
SAS_PROTOCOL_SATA and SAS_PROTOCOL_STP. Provide a SAS_PROTOCOL_STP_ALL
to silence warnings like:
drivers/scsi/pm8001/pm8001_sas.c:438:3: warning: case value ‘5’ not in enumerated type ‘enum sas_protocol’ [-Wswitch]
drivers/scsi/mvsas/mv_sas.c:798:2: warning: case value ‘5’ not in enumerated type ‘enum sas_protocol’ [-Wswitch]
drivers/scsi/mvsas/mv_sas.c:1783:2: warning: case value ‘5’ not in enumerated type ‘enum sas_protocol’ [-Wswitch]
drivers/scsi/mvsas/mv_sas.c:1886:2: warning: case value ‘5’ not in enumerated type ‘enum sas_protocol’ [-Wswitch]
drivers/scsi/isci/request.c:3565:2: warning: case value ‘5’ not in enumerated type ‘enum sas_protocol’ [-Wswitch]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If the user has disabled CONFIG_SCSI_SAS_HOST_SMP then libsas drivers
will not be receiving smp-gpio frames and do not need this lookup code.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Tested-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Allow expander table-to-table attachments for
expanders that support it.
Signed-off-by: Luben Tuikov <ltuikov@yahoo.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add SFF-8485 v0.7 / SAS-1 smp-write-gpio register support to libsas.
Defer SAS-2 support unless/until it defines an sgpio interface.
Minimum implementation needed to get the lights blinking.
try_test_sas_gpio_gp_bit() provides a common method to parse the
incoming write data (raw bitstream), and the to_sas_gpio_gp_bit() helper
routine can be used as a basis for the set/clear operations for the
'read' implementation. Host implementations parse as many bits
(ODx.[012]) as are locally supported and report the number of registers
successfully written. If the submitted data overruns the internal
number of registers available report the write as a success with the
number of bytes remaining reported in ->resid_len.
Example (assuming an active backplane) set the "identify" pattern for
the first 21 devices:
smp_write_gpio --count=2 --data=92,49,24,92,24,92,49,24 -t 4 --index=1 /dev/bsg/sas_hostX
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Some device handler types are not tied to the vendor/model
but rather to a specific capability. Eg ALUA is supported
if the 'TPGS' setting in the standard inquiry is set.
This patch implements a 'match' callback for device handler
which supersedes the original vendor/model lookup and
implements the callback for the ALUA handler.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Instead of issuing a standard inquiry from within the
alua device handler we can evaluate the TPGS setting from
the existing inquiry data of the sdev and save us the I/O.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The problem is that if we are doing a scsi scan then the device goes
into recovery then we will wait for the recovery to complete. It waits
because scsi-ml will send inquiries or report luns and the queueing code
will have been blocked due to the host not being ready. However, if we
are in recovery and then a scan is started the scan will silently fail
and some devices will not be added.
It is easy to hit the problem where devices do not show up with
FC where we are doing tests that disrupt the target controllers.
When the controller is disruprted (reboot, or setting firmware, etc),
and we cause the dev loss tmo to fire then devices will be removed
Then when the problem has been fixed, the rport will be scanned and
devices should be added back. But if we cause another disruption before
scanning has started then devices will not get added back. If the problem
is not started until the scan is started then the devices will be added
back.
This patch fixes that problem by not failing scans when the host
is in recovery. We will let scsi-ml send the IO and let the queueing
and scsi error handling deal with it like is done if we went into
recovery while scanning.
For recovery cases where the host is being torn down then with the
patch we will still fail the scan since there is not point in scanning.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Added new sysfs attr 'host_reset' in scsi_sysfs.c to
perform adapter or firmware reset as suggested by
Mike Christie here:
http://marc.info/?l=linux-scsi&m=127359347111167&w=2
user/application can write "adapter" or "firmware" on
this attr and it will call newly added function hook
in scsi_host_template to call LDD adapter or firmware
reset implementation.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Offload drivers like qla4xxx will offload the sending of the login/logout
pdus still, so this patch adds iscsi_conn_login_event which is
used by these types of drivers to notify userspace that the connection
has changed state.
It also adds a iscsi_is_session_online helper so the lld
can query the sessions state field.
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch adds bsg support to the iscsi class. There is only
1 request, the host vendor one, supported. It is expected that
this would be used for things like flash updates.
This patch is made over this one
http://marc.info/?l=linux-scsi&m=131149780020992&w=2
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add support to set vlan priority and enable/disble a vlan.
Patch based on code from Vikas Chaudhary.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The iscsi class currently does not support writable sysfs
attrs for LLD sysfs settings. This patch converts the
iscsi class and driver's host attrs to use the attribute
container sysfs group and the sysfs group's is_visible callout
to be able to support readable or writable sysfs attrs.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
We can replace the iface param mask with the
attr_is_visible callback.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The iscsi class currently does not support writable sysfs
attrs for LLD sysfs settings. This patch converts the
iscsi class and driver's session attrs to use the attribute
container sysfs group and the sysfs group's is_visible callout
to be able to support readable or writable sysfs attrs.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The iscsi class currently does not support writable sysfs
attrs for LLD sysfs settings. This patch converts the
iscsi class and drivers to use the attribute container
sysfs group and the sysfs group's is_visible callout
to be able to support readable or writable sysfs attrs.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
A iscsi host can have multiple interfaces. This patch
adds a new iface iscsi class for this. It exports the
network settings now, and will be extended to also
export iscsi initiator port settings like the isid
and initiator name for drivers that can support multiple
initiator ports.
Based on patch from Lalit Chandivade.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Allows user space (iscsiadm) to send down network configuration
parameters for LLD to set private network configuration on the iSCSI
adapters.
Based on patch from Lalit Chandivade.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Export fcoe_get_wwn, fcoe_validate_vport_create and fcoe_wwn_to_str so that all
LLDs can use these common function.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Now that isci has added a 3rd open coded user of this functionality just
share the libsas version.
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
* 'for-linus' of git://git.open-osd.org/linux-open-osd:
ore: Make ore its own module
exofs: Rename raid engine from exofs/ios.c => ore
exofs: ios: Move to a per inode components & device-table
exofs: Move exofs specific osd operations out of ios.c
exofs: Add offset/length to exofs_get_io_state
exofs: Fix truncate for the raid-groups case
exofs: Small cleanup of exofs_fill_super
exofs: BUG: Avoid sbi realloc
exofs: Remove pnfs-osd private definitions
nfs_xdr: Move nfs4_string definition out of #ifdef CONFIG_NFS_V4
ORE stands for "Objects Raid Engine"
This patch is a mechanical rename of everything that was in ios.c
and its API declaration to an ore.c and an osd_ore.h header. The ore
engine will later be used by the pnfs objects layout driver.
* File ios.c => ore.c
* Declaration of types and API are moved from exofs.h to a new
osd_ore.h
* All used types are prefixed by ore_ from their exofs_ name.
* Shift includes from exofs.h to osd_ore.h so osd_ore.h is
independent, include it from exofs.h.
Other than a pure rename there are no other changes. Next patch
will move the ore into it's own module and will export the API
to be used by exofs and later the layout driver
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (71 commits)
[SCSI] fcoe: cleanup cpu selection for incoming requests
[SCSI] fcoe: add fip retry to avoid missing critical keep alive
[SCSI] libfc: fix warn on in lport retry
[SCSI] libfc: Remove the reference to FCP packet from scsi_cmnd in case of error
[SCSI] libfc: cleanup sending SRR request
[SCSI] libfc: two minor changes in comments
[SCSI] libfc, fcoe: ignore rx frame with wrong xid info
[SCSI] libfc: release exchg cache
[SCSI] libfc: use FC_MAX_ERROR_CNT
[SCSI] fcoe: remove unused ptype field in fcoe_rcv_info
[SCSI] bnx2fc: Update copyright and bump version to 1.0.4
[SCSI] bnx2fc: Tx BDs cache in write tasks
[SCSI] bnx2fc: Do not arm CQ when there are no CQEs
[SCSI] bnx2fc: hold tgt lock when calling cmd_release
[SCSI] bnx2fc: Enable support for sequence level error recovery
[SCSI] bnx2fc: HSI changes for tape
[SCSI] bnx2fc: Handle REC_TOV error code from firmware
[SCSI] bnx2fc: REC/SRR link service request and response handling
[SCSI] bnx2fc: Support 'sequence cleanup' task
[SCSI] dh_rdac: Associate HBA and storage in rdac_controller to support partitions in storage
...
There is no need to cache the ptype in fcoe_rcv_info struct as it is never
used anywhere.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target: Convert to DIV_ROUND_UP_SECTOR_T usage for sectors / dev_max_sectors
kernel.h: Add DIV_ROUND_UP_ULL and DIV_ROUND_UP_SECTOR_T macro usage
iscsi-target: Add iSCSI fabric support for target v4.1
iscsi: Add Serial Number Arithmetic LT and GT into iscsi_proto.h
iscsi: Use struct scsi_lun in iscsi structs instead of u8[8]
iscsi: Resolve iscsi_proto.h naming conflicts with drivers/target/iscsi
This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>
Signed-off-by: Arun Sharma <asharma@fb.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
fs: Merge split strings
treewide: fix potentially dangerous trailing ';' in #defined values/expressions
uwb: Fix misspelling of neighbourhood in comment
net, netfilter: Remove redundant goto in ebt_ulog_packet
trivial: don't touch files that are removed in the staging tree
lib/vsprintf: replace link to Draft by final RFC number
doc: Kconfig: `to be' -> `be'
doc: Kconfig: Typo: square -> squared
doc: Konfig: Documentation/power/{pm => apm-acpi}.txt
drivers/net: static should be at beginning of declaration
drivers/media: static should be at beginning of declaration
drivers/i2c: static should be at beginning of declaration
XTENSA: static should be at beginning of declaration
SH: static should be at beginning of declaration
MIPS: static should be at beginning of declaration
ARM: static should be at beginning of declaration
rcu: treewide: Do not use rcu_read_lock_held when calling rcu_dereference_check
Update my e-mail address
PCIe ASPM: forcedly -> forcibly
gma500: push through device driver tree
...
Fix up trivial conflicts:
- arch/arm/mach-ep93xx/dma-m2p.c (deleted)
- drivers/gpio/gpio-ep93xx.c (renamed and context nearby)
- drivers/net/r8169.c (just context changes)
This patch moves the iscsi_sna_lt() and iscsi_sna_lte(), along with
iscsi_sna_gt() and iscsi_sna_gte() from iscsi_target_mod into
static inlines inside of include/scsi/iscsi_proto.h
This patch also includes the ISCSI_HDR_LEN and ISCSI_CRC_LEN
definitions.
(Added JesperJ simpliciation for iscsi_sna_* usage)
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
struct scsi_lun is also just a struct with an array of 8 octets (64 bits)
but using it instead in iscsi structs lets us call scsilun_to_int
without a cast, and also lets us copy it using assignment, instead of
memcpy().
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch renames the following iscsi_proto.h structures to avoid
namespace issues with drivers/target/iscsi/iscsi_target_core.h:
*) struct iscsi_cmd -> struct iscsi_scsi_req
*) struct iscsi_cmd_rsp -> struct iscsi_scsi_rsp
*) struct iscsi_login -> struct iscsi_login_req
This patch includes useful ISCSI_FLAG_LOGIN_[CURRENT,NEXT]_STAGE*,
and ISCSI_FLAG_SNACK_TYPE_* definitions used by iscsi_target_mod, and
fixes the incorrect definition of struct iscsi_snack to following
RFC-3720 Section 10.16. SNACK Request.
Also, this patch updates libiscsi, iSER, be2iscsi, and bn2xi to
use the updated structure definitions in a handful of locations.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
All these are instances of
#define NAME value;
or
#define NAME(params_opt) value;
These of course fail to build when used in contexts like
if(foo $OP NAME)
while(bar $OP NAME)
and may silently generate the wrong code in contexts such as
foo = NAME + 1; /* foo = value; + 1; */
bar = NAME - 1; /* bar = value; - 1; */
baz = NAME & quux; /* baz = value; & quux; */
Reported on comp.lang.c,
Message-ID: <ab0d55fe-25e5-482b-811e-c475aa6065c3@c29g2000yqd.googlegroups.com>
Initial analysis of the dangers provided by Keith Thompson in that thread.
There are many more instances of more complicated macros having unnecessary
trailing semicolons, but this pile seems to be all of the cases of simple
values suffering from the problem. (Thus things that are likely to be found
in one of the contexts above, more complicated ones aren't.)
Signed-off-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The fcoe driver can implement ddp_targ() similarly to ddp_setup() when fcoe
stack works with existing target frame, e.g., tcm, where the ddp_targ() would
eventually point to the underlying hardware driver's implementation of
ndo_fcoe_ddp_targ() through net_device_ops. This new API sets up DDP context
for target appropriately by setting required bits for DDP context.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
struct scsi_lun is also just a struct with an array of 8 octets (64 bits)
but using it instead in iscsi structs lets us call scsilun_to_int
without a cast, and also lets us copy it using assignment, instead of
memcpy().
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Dan Williams