Add the correct silicon variant code ID (0x5) to the driver. This
new code is the 'production' variant code ID for DA9063.
This patch will remove the older variant code ID which matches the
pre-production silicon ID (0x3) for the DA9063 chip.
There is also some small amount of correction done in this patch:
it splits the revision code and correctly names it according to
the hardware specification and moves the dev_info() call before
the variant ID test.
Signed-off-by: Opensource [Steve Twiss] <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Return directly to avoid redundant lines of code.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Realtek USB card reader provides a channel to transfer command or data to flash
memory cards. This driver exports host instances for mmc and memstick subsystems
and handles basic works.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Roger Tseng <rogerable@realtek.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
stw481x_regmap_config is local to this file.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add this header explicitly for IS_ERR and friends.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
'site' variable should be initialized with 0 so that when 'site'
property doesn't exist in DTB it can be handled correctly.
'0' value means board site number is motherboard (see
Documentation/devicetree/bindings/arm/vexpress.txt for details).
Signed-off-by: Semen Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
During probe the driver allocates two dummy I2C devices for subchips in
function pm800_pages_init(). Additionally this function allocates
regmaps for these subchips. If any of these steps fail then these dummy
I2C devices are not freed and resources leak.
On pm800_pages_init() fail the driver must call pm800_pages_exit() to
unregister dummy I2C devices.
Cc: stable@vger.kernel.org
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use devm_ioremap_resource() in order to make the code simpler,
and remove redundant return value check of platform_get_resource()
because the value is checked by devm_ioremap_resource().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Three of the PMIC registers have some bits that are changed
autonomously by the PMIC itself (some time) after being set
by some component driver of the DA9052 PMIC and hence they
need to be marked as volatile so that the regmap API will
not cache their values.
Acked-by: David Dajun Chen <david.chen@diasemi.com>
Signed-off-by: Anthony Olech <anthony.olech.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
During probe the driver allocates dummy I2C devices for MUIC and haptic
with i2c_new_dummy() but it does not check the return value of this
calls.
In case of error (i2c_new_device(): memory allocation failure or I2C
address cannot be used) this function returns NULL which is later used
by devm_regmap_init_i2c() and i2c_unregister_device().
If i2c_new_dummy() fails for MUIC or haptic devices, fail also the probe
for main MFD driver.
Cc: stable@vger.kernel.org
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
During probe the driver allocates dummy I2C device for companion chip
with i2c_new_dummy() but it does not check the return value of this call.
In case of error (i2c_new_device(): memory allocation failure or I2C
address cannot be used) this function returns NULL which is later used
by regmap_init_i2c().
If i2c_new_dummy() fails for companion device, fail also the probe for
main MFD driver.
Cc: stable@vger.kernel.org
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
During probe the driver allocates dummy I2C device for companion chip
and then allocates a regmap for it. If regmap_init_i2c() fails then the
I2C driver (allocated with i2c_new_dummy()) is not freed and this
resource leaks.
Cc: stable@vger.kernel.org
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
During probe the driver allocates dummy I2C devices for RTC and ADC
with i2c_new_dummy() but it does not check the return value of this
calls.
In case of error (i2c_new_device(): memory allocation failure or I2C
address cannot be used) this function returns NULL which is later used
by i2c_unregister_device().
If i2c_new_dummy() fails for RTC or ADC devices, fail also the probe
for main MFD driver.
Cc: stable@vger.kernel.org
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
During probe the driver allocates dummy I2C device for RTC with i2c_new_dummy() but it does not check the return value of this call.
In case of error (i2c_new_device(): memory allocation failure or I2C
address cannot be used) this function returns NULL which is later used
by i2c_unregister_device().
If i2c_new_dummy() fails for RTC device, fail also the probe for
main MFD driver.
Cc: stable@vger.kernel.org
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
During probe the driver allocates dummy I2C device for RTC with
i2c_new_dummy() but it does not check the return value of this call.
In case of error (i2c_new_device(): memory allocation failure or I2C
address cannot be used) this function returns NULL which is later used
by i2c_unregister_device().
If i2c_new_dummy() fails for RTC device, fail also the probe for main
MFD driver.
Cc: stable@vger.kernel.org
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
During probe the driver allocates dummy I2C devices for RTC, haptic and
MUIC with i2c_new_dummy() but it does not check the return value of this
calls.
In case of error (i2c_new_device(): memory allocation failure or I2C
address cannot be used) this function returns NULL which is later used
by i2c_unregister_device().
If i2c_new_dummy() fails for RTC, haptic or MUIC devices, fail also the
probe for main MFD driver.
Cc: stable@vger.kernel.org
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Semicolon is not necessary after the while statement.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The TPS65218 chip is a power management IC for Portable Navigation Systems
and Tablet Computing devices. It contains the following components:
- Regulators.
- Over Temperature warning and Shut down.
This patch adds support for tps65218 mfd device. At this time only
the regulator functionality is made available.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This changes the following mechanisms in the TC3589x device tree
probing path:
- Use the .of_match_table in struct device_driver to match the
device in the device tree.
- Add matches for the proper compatible strings "toshiba,..."
and all sub-variants, just as is done for the .id matches.
- Move over all the allocation of platform data etc to the
tc3589x_of_probe() function and follow the pattern of passing
a platform data pointer back, or an error pointer on error,
as found in the STMPE driver.
- Match the new (proper) compatible strings for the GPIO and
keypad MFD cells.
- Use of_device_is_compatible() rather than just !strcmp()
to discover which cells to instantiate.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Expose some DSP registers which are useful for DSP users to be able to
access whilst debugging their firmware.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Expose some DSP registers which are useful for DSP users to be able to
access whilst debugging their firmware.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add of_compatible ("maxim,max14577-muic") to the mfd_cell for extcon
driver. If entry with such compatible is present in the DTS, the extcon
driver will have of_node set.
This may be useful for extcon consumers and it is documented in
bindings documentation.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
It is currently not possible to select the SA1100 or Vexpress
drivers in the MFD subsystem, because the menu for the entire
subsystem ends before these options are presented.
Move the main menu closing and the endif for HAS_IOMEM to the
end of the file so these are selectable again.
Cc: stable@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Update the register patch based on latest evaluation of the device.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add the necessary entries required for S2MPA01 multi-function
device. While at it also convert whitespaces to tabs in core.h.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
When used 64bit compiler GCC warns as
drivers/mfd/sec-core.c:199:10: warning:
cast from pointer to integer of different size [-Wpointer-to-int-cast]
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
During probe the sec-core driver allocates dummy I2C device for RTC with
i2c_new_dummy() but return value is not checked. In case of error
(i2c_new_device(): memory allocation failure or I2C address cannot be
used) this function returns NULL which is later used by
devm_regmap_init_i2c() or i2c_unregister_device().
If i2c_new_dummy() fails for RTC device, fail also the probe for main
MFD driver.
Cc: stable@vger.kernel.org
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add support for S2MPS14 PMIC device to the MFD sec-core driver.
The S2MPS14 is similar to S2MPS11 but it has fewer regulators, two
clocks instead of three and a little different registers layout.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The S2MPS11 RTC has two alarms: alarm0 and alarm1 (corresponding
interrupts are named similarly). Use consistent names for interrupts to
limit possible errors.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch prepares for adding support for S2MPS14 RTC driver by
selecting different regmaps for S2MPS1X/S5M876X RTC devices.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add maximum register to the regmap used by rtc-s5m driver.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This is a driver for an A/D converter, which belongs into
drivers/iio/adc.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Simplify reading and writing of 16 bit TWL registers in the
driver by using twl_i2c_read_u16 and twl_i2c_write_u16.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Tested-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Some style fixes in twl4030-madc driver.
Reported-by: Jonathan Cameron <jic23@kernel.org>
Reported-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sebastian Reichel <sre@debian.org>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Tested-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This converts twl4030-madc module to use the Industrial IO ADC
framework and adds device tree support.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Tested-by: Marek Belisko <marek@goldelico.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Update twl4030-madc driver to use managed resources.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Tested-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
These are sent separately from the rest of the .dts changes
as these depend on the fixes merged into v3.14-rc4, and
needed a bit more time to get updated on the fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=rAdr
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.15/dt-overo-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Updates to the .dts files to support more Gumstix boards.
These are sent separately from the rest of the .dts changes
as these depend on the fixes merged into v3.14-rc4, and
needed a bit more time to get updated on the fixes.
* tag 'omap-for-v3.15/dt-overo-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Add support for the Overo Summit
ARM: dts: Add support for the Overo Chestnut43
ARM: dts: Add support for the Overo Alto35
ARM: dts: Add support for the Overo Gallop43
ARM: dts: Add support for the Overo Palo43
ARM: dts: overo: Add LIS33DE accelerometer
ARM: dts: overo: Create a file for common Gumstix peripherals
ARM: dts: overo: Push uart3 pinmux down to expansion board
ARM: dts: omap3-tobi: Add AT24C01 EEPROM
ARM: dts: omap3-tobi: Use include file omap-gpmc-smsc9221
ARM: dts: omap: Add common file for SMSC9221
ARM: dts: omap3-overo: Add HSUSB PHY
ARM: dts: omap3-overo: Enable WiFi/BT combo
ARM: dts: omap3-overo: Add missing pinctrl
ARM: dts: omap3-tobi: Add missing pinctrl
ARM: dts: overo: reorganize include files
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Conflicts:
arch/arm/boot/dts/omap3-overo.dtsi
Use a meaningful name for the reference clocks so that it indicates the
function.
Update the OMAP4+ USB Host node as well to be in sync with the changes.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use the proper clock name 'usbhost_120m_fck' instead of the
alias 'ehci_logic_fck'
Get rid of the 'ehci_logic_fck' alias from the OMAP3 hwmod data
as well.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Be more strict and always fail on clk_get() error.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Not all revisions have all the clocks so get the necessary clocks
based on hardware revision.
This should avoid un-necessary clk_get failure messages that were
observed earlier.
Also remove the dummy USB host clocks from the OMAP3 clock data.
These are no longer expected by the driver.
Acked-by: Mike Turquette <mturquette@linaro.org> [OMAP3 CLK data]
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Static analysis from cppcheck issued the following warning:
[drivers/mfd/omap-usb-tll.c:255]: (warning) Found calculation
inside sizeof().
The current size calculation is not obvious and is easy to
miscomprehend, so re-work the size of the allocation based
on the size of the struct pointer and quantity to allocate.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The DBx500 and ABx500 should be getting their IRQs from the
device tree and nowhere else. Get rid of all the static assignments
everywhere, delete it from the driver, platform data and the
board files in one swift strike.
Lots of cross-dependencies in the MFD drivers for PRCMU and
AB8500 makes it necessary to strike everywhere at once to
eradicate IRQs passed as resources and platform data to the left
and right around the platform.
Cc: Mark Brown <broonie@kernel.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On the wm5102 the register patches are applied manually, rather than by
the regmap core. This application is wrapped in calls to
regcache_cache_bypass. However, this is dangerous as other threads may
be accessing the hardware at the same time as the pm_runtime operations
and if they do so during the period whilst cache_bypass is enabled those
writes will miss the cache when they shouldn't.
Apply the register patch using the new regmap_multi_reg_write_bypassed
function to avoid this problem. Also remove the call to
regcache_cache_bypass from the hardware patch application as it is
unneeded there and creates a similar window for writes to miss the
cache.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
This time we got a slightly higher volume than previous times,
but all device-specific good fixes. Noticeable changes are fixes in
davinci, and the removal of open-codes in HD-audio ca0132 driver.
The rest are all small fixes and/or quirks.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=96St
-----END PGP SIGNATURE-----
Merge tag 'sound-3.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This time we got a slightly higher volume than previous times, but all
device-specific good fixes. Noticeable changes are fixes in davinci,
and the removal of open-codes in HD-audio ca0132 driver. The rest are
all small fixes and/or quirks"
* tag 'sound-3.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Enable front audio jacks on one HP desktop model
ALSA: hda/ca0132 - Fix recording from mode id 0x8
ALSA: hda/ca0132 - setup/cleanup streams
ALSA: hda - add headset mic detect quirks for two Dell laptops
ALSA: usb-audio: work around KEF X300A firmware bug
ASoC: max98090: make REVISION_ID readable
ASoC: txx9aclc_ac97: Fix kernel crash on probe
ASoC: max98090: sync regcache on entering STANDBY
ASoC: blackfin: Fix machine driver Kconfig dependencies
ASoC: da9055: Fix device registration of PMIC and CODEC devices
ASoC: fsl-esai: fix ESAI TDM slot setting
ASoC: fsl: fix pm support of machine drivers
ASoC: rt5640: Add ACPI ID for Intel Baytrail
ASoC: davinci-evm: Add pm callbacks to platform driver
ASoC: davinci-mcasp: Consolidate pm_runtime_get/put() use in the driver
ASoC: davinci-mcasp: Configure xxTDM, xxFMT and xxFMCT registers synchronously
ASoC: davinci-mcasp: Harmonize the sub hw_params function names
ASoC: samsung: Fix trivial typo
ASoC: samsung: Remove invalid dependencies
ASoC: wm8993: drop regulator_bulk_free of devm_ allocated data
If CONFIG_PM_SLEEP=n:
drivers/mfd/sec-core.c:349: warning: ‘sec_pmic_suspend’ defined but not used
drivers/mfd/sec-core.c:371: warning: ‘sec_pmic_resume’ defined but not used
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If CONFIG_PM_SLEEP=n:
drivers/mfd/max14577.c:177: warning: ‘max14577_suspend’ defined but not used
drivers/mfd/max14577.c:200: warning: ‘max14577_resume’ defined but not used
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If we compile the TPS65217 for a 64bit architecture we receive the following
warnings:
drivers/mfd/tps65217.c: In function ‘tps65217_probe’:
drivers/mfd/tps65217.c:173:13:
warning: cast from pointer to integer of different size
chip_id = (unsigned int)match->data;
^
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If we compile the WM8994 for a 64bit architecture we receive the following
warnings:
drivers/mfd/wm8994-core.c: In function ‘wm8994_i2c_probe’:
drivers/mfd/wm8994-core.c:639:19:
warning: cast from pointer to integer of different size
wm8994->type = (int)of_id->data;
^
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If we compile the MAX8998 for a 64bit architecture we receive the following
warnings:
drivers/mfd/max8998.c: In function ‘max8998_i2c_get_driver_data’:
drivers/mfd/max8998.c:178:10:
warning: cast from pointer to integer of different size
return (int)match->data;
^
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If we compile the MAX8997 for a 64bit architecture we receive the following
warnings:
drivers/mfd/max8997.c: In function ‘max8997_i2c_get_driver_data’:
drivers/mfd/max8997.c:173:10:
warning: cast from pointer to integer of different size
return (int)match->data;
^
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Currently the I2C device Ids conflict for the MFD and CODEC so
cannot be both instantiated on one platform. This patch updates
the Ids and names to make them unique from each other.
It should be noted that the I2C addresses for both PMIC and CODEC
are modifiable so instantiation of the two are kept as separate
devices, rather than instantiating the CODEC from the MFD code.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Acked-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
A respin of the merges in the previous pull request with one extra fix.
A quiet release for the regulator API, quite a large number of small
improvements all over but other than the addition of new drivers for the
AS3722 and MAX14577 there is nothing of substantial non-local impact.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJS4QTYAAoJELSic+t+oim92bMP/09kMG+4zS6TGM+ljselfYLQ
XmqEAfLpND+07HmxlCRMHIRdrzMm7QrrW076UT3u6Q/RUi6L7LjXWdFNhm9d7k4V
l45lvpo8C+bJkmX9Y9+dBPKbY5qnz9Kttpr/8wn0uAz1zhqhCCG2GYp0eV7Qcz7L
XrBfiWmmeu11ArFtQcVPheGMdjiG2hpxbHqJ4e5nZ8kJ3C31RgfTR2r8xA8xr99H
LhzuwoKjlsjzIuXUgd2F/i4TqtOkpg69wQocRnOYyyEpd4TnI+q4pk4GiMx4EuH1
GMZ/XGmd1GuiAa7hXIWOyz7vNe54RPoLTWN8QEaYGXf8m/AUUVbje33BTtWbwEeU
VXWbKpNEWWzykE6lPtxY9I0KMYbqAUvcflIL7kLYbxLS6RE5U4+dwYVEF0gwAWor
svwgwXhjzNCJhb+DQlzKQa2zcWwJr0uT+DllPXEXJE5yIIn7cHEraYcS4cPfLNL5
MLnB9BGX5zJQDJVsex/8jnCafI7M/CefIB06CbLK4klR1OtyTJc3yEhGCgWlJU4C
NKdUbUhirCkPqY2v4RwWwOaxGs0WFWsyd5gYhCy3gL7O22pGW5yGO3MG524mRWrU
ccU9lbpXgtHTTcb+RKBEwr9fWEcsCIt5gImcRoMxqfkjY0CsQJD8tVdl4Md7OYYv
BjJexZZulWce7R3F7+Kf
=1NsR
-----END PGP SIGNATURE-----
Merge tag 'regulator-v3.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"A respin of the merges in the previous pull request with one extra
fix.
A quiet release for the regulator API, quite a large number of small
improvements all over but other than the addition of new drivers for
the AS3722 and MAX14577 there is nothing of substantial non-local
impact"
* tag 'regulator-v3.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (47 commits)
regulator: pfuze100-regulator: Improve dev_info() message
regulator: pfuze100-regulator: Fix some checkpatch complaints
regulator: twl: Fix checkpatch issue
regulator: core: Fix checkpatch issue
regulator: anatop-regulator: Remove unneeded memset()
regulator: s5m8767: Update LDO index in s5m8767-regulator.txt
regulator: as3722: set enable time for SD0/1/6
regulator: as3722: detect SD0 low-voltage mode
regulator: tps62360: Fix up a pointer-integer size mismatch warning
regulator: anatop-regulator: Remove unneeded kstrdup()
regulator: act8865: Fix build error when !OF
regulator: act8865: register all regulators regardless of how many are used
regulator: wm831x-dcdc: Remove unneeded 'err' label
regulator: anatop-regulator: Add MODULE_ALIAS()
regulator: act8865: fix incorrect devm_kzalloc for act8865
regulator: act8865: Remove set_suspend_[en|dis]able implementation
regulator: act8865: Remove unneeded regulator_unregister() calls
regulator: s2mps11: Clean up redundant code
regulator: tps65910: Simplify setting enable_mask for regulators
regulator: act8865: add device tree binding doc
...
Fix up the following pointer-integer size mismatch warning in
tps65217_probe():
drivers/mfd/tps65217.c: In function 'tps65217_probe':
drivers/mfd/tps65217.c:173:13: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
chip_id = (unsigned int)match->data;
^
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: AnilKumar Ch <anilkumar@ti.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix up the following pointer-integer size mismatch warning in
max8998_i2c_get_driver_data():
drivers/mfd/max8998.c: In function 'max8998_i2c_get_driver_data':
drivers/mfd/max8998.c:178:10: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
return (int)match->data;
^
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Mark Brown <broonie@linaro.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
New drivers
- Samsung Maxim 14577; Micro USB, Regulator, IRQ Controller and Battery Charger
- TI/National Semiconductor LP3943 I2C GPIO Expander and PWM Generator
Existing driver adaptions
- Expansion of Wolfson Arizona DSP and High-Pass filter controls
- TI TWL6040 default Regmap support and Regcache addition/bypass
- Some nice Smatch catch fixes
- Conversion of TI OMAP-USB and TI TWL6030 to endian neutralness
- ChromeOS EC timing (delay) adaptions and added dependency on OF
- Many constifications of 'struct {mfd_cell,regmap_irq,et. al}'
- Watchdog support added for NVIDIA AS3722
- Convert functions to static in TI AM335x
- Realigned previously defeated functionality in TI AM335x
- IIO ADC-TSC concurrency dead-lock/timeout resolution
- Addition of Power Management and Clock support for Samsung core
- DEFINE_PCI_DEVICE_TABLE macro removal from MFD Subsystem
- Greater use of irqdomain functionality in ST-E AB8500
- Removal of 'include/linux/mfd/abx500/ab8500-gpio.h'
- Wolfson WM831x PMIC Power Management changes s/poweroff/shutdown/
- Device Tree documentation added for TI/Nat Semi LP3943
- Version detection and voltage tables for TI TPS6586x PMIC devices
- Simplification of Freescale MC13XXX (de-)initialisation routines
- Clean-up and simplification of the Realtek parent driver
- Added support for RTL8402 Realtek PCI-Express card reader
- Resource leak fix for Maxim 77686
- Possible suspend BUG() fix in OMAP USB TLL
- Support for new Wolfson WM5110 Revision (D)
- Testing of automatic assignment of of_node in mfd_add_device()
- Reversion of the above when it started to cause issues
- Remove legacy Platform Data from;
TI TWL Core, Qualcomm SSBI and ST-E ABx500 Pinctrl
- Clean-ups; tabbing issues, function name changes, 'drvdata = NULL' removal,
unused uninitialised warning mitigation, error message clarity,
removal of redundant/duplicate checks, licensing (GPL -> GPL2),
coding consistency, duplicate function declaration, ret checks,
commit corrections, redundant of_match_ptr() helper removal,
spelling, #if-deffery removal and header guards name changes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQIbBAABAgAGBQJS3pLGAAoJEFGvii+H/HdhmkkP93Hrd9FBjVpmUQcOrghFDd//
vte2LVDovXDcwm7i+BdZNG3+2aWtliTQXIw8PaAziUTwMlDNtT2B6GBFnIff4aXB
Em/Oh6Je7r1gom1gMPCuefRrInTk0xEXy9Oazp4Hn4in71T+8PHNlEHdxEojakEm
H5FnjAfgISEsA5twSyO9efVLNqPd3UQqg3O571oKwfuSED70YSCW2Yyaoiz4pnE5
0WwZ9cel+sP7CIuyuR4TumUSDeBIAnYnZWqjqXZ1ueMWcm2RNVqeFrt/w0uoZjOA
yBg8ZMfkBcePd6qnifqVqagRW/jW1bxmUeIHkp0bWeMqWN6Yyypitz8ZW+Qi7Swa
OcmgM9V7OW1WG9FF7HoLbYHIPzmBb6duGtcCfAir4m8HJjyPfTuJpOshBW1F3+VG
yEf5a1fj2NO34kvIbLec2f7MveIMmZxzWaoOx+ET9/WPknilifgyp7eDH24pQwI4
5Lo5Z5uAfBCT3roOzHxCLl2nVXQoC66iTwdnneiEOn4rB/ApjfGVvGGd0VT6TD+g
z3RqxpTdkd0AtjfeF778uTDBEKu7HZkqmlBP8HKWCBEAzqcKg7BpjYw0ajgmVwKr
QiuBuWcEZ/2vVt8Qot7y5Vx89Q4AQwOqc24SldtQLu46iPAuKt+GizzHRw3IxBiQ
VU9Aq/VoaTHBLS91tDE=
=PuTE
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.14-1' of git://git.linaro.org/people/ljones/mfd
Pull MFD changes from Lee Jones:
"New drivers
- Samsung Maxim 14577; Micro USB, Regulator, IRQ Controller and
Battery Charger
- TI/National Semiconductor LP3943 I2C GPIO Expander and PWM
Generator
Existing driver adaptions
- Expansion of Wolfson Arizona DSP and High-Pass filter controls
- TI TWL6040 default Regmap support and Regcache addition/bypass
- Some nice Smatch catch fixes
- Conversion of TI OMAP-USB and TI TWL6030 to endian neutralness
- ChromeOS EC timing (delay) adaptions and added dependency on OF
- Many constifications of 'struct {mfd_cell,regmap_irq,et.al}'
- Watchdog support added for NVIDIA AS3722
- Convert functions to static in TI AM335x
- Realigned previously defeated functionality in TI AM335x
- IIO ADC-TSC concurrency dead-lock/timeout resolution
- Addition of Power Management and Clock support for Samsung core
- DEFINE_PCI_DEVICE_TABLE macro removal from MFD Subsystem
- Greater use of irqdomain functionality in ST-E AB8500
- Removal of 'include/linux/mfd/abx500/ab8500-gpio.h'
- Wolfson WM831x PMIC Power Management changes s/poweroff/shutdown/
- Device Tree documentation added for TI/Nat Semi LP3943
- Version detection and voltage tables for TI TPS6586x PMIC devices
- Simplification of Freescale MC13XXX (de-)initialisation routines
- Clean-up and simplification of the Realtek parent driver
- Added support for RTL8402 Realtek PCI-Express card reader
- Resource leak fix for Maxim 77686
- Possible suspend BUG() fix in OMAP USB TLL
- Support for new Wolfson WM5110 Revision (D)
- Testing of automatic assignment of of_node in mfd_add_device()
- Reversion of the above when it started to cause issues
- Remove legacy Platform Data from;
TI TWL Core, Qualcomm SSBI and ST-E ABx500 Pinctrl
- Clean-ups; tabbing issues, function name changes, 'drvdata = NULL'
removal, unused uninitialised warning mitigation, error
message clarity, removal of redundant/duplicate checks,
licensing (GPL -> GPL2), coding consistency, duplicate
function declaration, ret checks, commit corrections,
redundant of_match_ptr() helper removal, spelling,
#if-deffery removal and header guards name changes"
* tag 'mfd-3.14-1' of git://git.linaro.org/people/ljones/mfd: (78 commits)
mfd: wm5110: Add register patch for rev D chip
mfd: omap-usb-tll: Don't hold lock during pm_runtime_get/put_sync()
gpio: lp3943: Remove redundant of_match_ptr helper
mfd: sta2x11-mfd: Use named constants for pci_power_t values
Documentation: mfd: Fix LDO index in s2mps11.txt
mfd: Cleanup mfd-mcp-sa11x0.h header
mfd: max8997: Use "IS_ENABLED(CONFIG_OF)" for DT code.
mfd: twl6030: Fix endianness problem in IRQ handler
mfd: sec-core: Add cells for S5M8767-clocks
mfd: max14577: Remove redundant of_match_ptr helper
mfd: twl6040: Fix sparse non static symbol warning
mfd: Revert "mfd: Always assign of_node in mfd_add_device()"
mfd: rtsx: Fix sparse non static symbol warning
mfd: max77693: Set proper maximum register for MUIC regmap
mfd: max77686: Fix regmap resource leak on driver remove
mfd: Represent correct filenames in file headers
mfd: rtsx: Add support for card reader rtl8402
mfd: rtsx: Add set pull control macro and simplify rtl8411
mfd: max8997: Enforce mfd_add_devices() return value check
mfd: mc13xxx: Simplify probe() & remove()
...
Evaluation of revision D of WM5110 suggests updates to the register
patch for optimal performance. For the sake of clarity rev C of the chip
does not require a register patch.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
pm_runtime_get/put_sync() can sleep so don't hold spinlock while
calling them.
This patch prevents a BUG() during system suspend when
CONFIG_DEBUG_ATOMIC_SLEEP is enabled.
Bug is present in Kernel versions v3.9 onwards.
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If nothing more than to improve code readability.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression pdev;
@@
pci_set_power_state(pdev,
- 0
+ PCI_D0
)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Instead of "#if define CONFIG_OF" use "IS_ENABLED(CONFIG_OF)"
option for DT code to avoid if-deffery in code.
Signed-off-by: Manish Badarkhe <badarkhe.manish@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The current TWL 6030 IRQ handler assumes little endianness.
This change makes it endian-neutral.
Signed-off-by: Danke Xie <d.xie@sta.samsung.com>
Signed-off-by: Taras Kondratiuk <taras.kondratiuk@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
S5M8767 chip has 3 crystal oscillators running at 32KHz. These are
supported by s2mps11-clk driver.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
'max14577_dt_match' is always compiled in. Hence the helper macro
is not needed.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fixes the following sparse warning:
drivers/mfd/twl6040.c:89:20: warning:
symbol 'twl6040_patch' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This reverts commit 68044bee13770918e0b28dd44aa98c889ec7558f.
We've had confirmed reports of this patch causing unforeseen issues
with existing MFD users. It has been agreed by the original author
and myself that reversion is the best solution.
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fixes the following sparse warning:
drivers/mfd/rtl8411.c:473:6: warning:
symbol 'rtl8411_init_common_params' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The MUIC block in max77693 has different I2C address than PMIC. The
driver allocated two regmaps: for PMIC and MUIC. However it used the
same regmap_config (with max_register field) for both regmaps. Actual
maximum address of register for MUIC is different than for PMIC.
Define another regmap_config for MUIC with proper max_register value.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The regmap used by max77686 MFD driver was not freed with regmap_exit()
on driver exit. This lead to leak of resources.
Replace regmap_init_i2c() call in driver probe with initialization of
managed register map so the regmap will be properly freed by the device
management code.
Cc: stable@vger.kernel.org
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
rtl8402 is much like rtl8411, so just add it to rtl8411.c
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add set pull control macro to reduce code for setting pull control, and
use a common init function to reduce code for rtl8411.c. So this patch
is used to just simplify code.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The original author provided a random return value check which is
redundant and seemingly floating. This patch not only relocates
the check so it is more clearly associated with the invokation of
mfd_add_devices(), but provides a store for the error value. We
also print a meaningful message on error before returning.
Signed-off-by: Laszlo Papp <lpapp@kde.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch simplifies probe() and remove() functions by moving
some initialisation code out from the I2C/SPI init() and exit()
functions and into the core driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Symbol MFD_MC13783 always selected by MFD_MC13XXX, so no need
to keep additional symbol.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In preparation for passing a const pointer directly to
ssbi_write() from the regmap APIs.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The ssbi driver assumes that the device is DT based. Remove the
platform data structs that will never be used and hide the enum
in the only C file that uses it.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
mfd_add_device() assigns .of_node in the device objects it creates only
if the mfd_cell for the device has the .of_compatible field set and the
DT node for the top-level MFD device contains a child whose compatible
property matches the cell's .of_compatible field.
This leaves .of_node unset in many cases. When this happens, entries in
the DT /aliases property which refer to the top-level MFD DT node will
never match the MFD child devices, hence causing the requested alias not
to be honored.
Solve this by setting each MFD child device's .of_node equal to the top-
level MFD device's .of_node field in the cases where it would otherwise
remain unset.
The first use-case for this will be aliases for the TPS6586x's RTC
device.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The EC has specific timing it requires. Add support for an optional delay
after raising CS to fix timing issues. This is configurable based on
a DT property "google,cros-ec-spi-msg-delay".
If this property isn't set, then no delay will be added. However, if set
it will cause a delay equal to the value passed to it to be inserted at
the end of a transaction.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Reviewed-by: Bernie Thompson <bhthompson@chromium.org>
Reviewed-by: Andrew Bresticker <abrestic@chromium.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
memset() was being called with the second parameter set to '\0', which
is equivalent but longer than the more canonical 0. Update the code to
use the latter variant consistently across the driver.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver is not used on any non-DT platform, so it can depend on the
OF Kconfig symbol to make that explicit. This is in preparation of a
subsequent patch which parses some parameters from the device tree and
would otherwise have to conditionalize that code.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
According to the header comment in the source file the driver is
licensed under GPL v2, so update MODULE_LICENSE() to match that.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fixes the following sparse warning:
drivers/mfd/sec-core.c:202:16: warning: Using plain integer as NULL pointer
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In case of error, the function devm_regmap_init_mmio() returns
ERR_PTR() and never returns NULL. The NULL test in the return
value check should be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Checking for maximal register is already provided by regmap API,
so remove redundant checks.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use the VERSIONCRC to determine the exact device version. According to
the datasheet this register can be used as device identifier. The
identification is needed since some tps6586x regulators use a different
voltage table.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
LP3943 has 16 output pins which can be used as GPIO expander and PWM generator.
* Regmap I2C interface for R/W LP3943 registers
* Atomic operations for output pin assignment
The driver should check whether requested pin is available or not.
If the pin is already used, pin request returns as a failure.
A driver data, 'pin_used' is checked when gpio_request() and
pwm_request() are called. If the pin is available, then pin_used is set.
And it is cleared when gpio_free() and pwm_free().
* Device tree support
Compatible strings for GPIO and PWM driver.
LP3943 platform data is PWM related, so parsing the device tree is
implemented in the PWM driver.
Signed-off-by: Milo Kim <milo.kim@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
"pdata" is a NULL not an ERR_PTR so there is no use printing it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This helps move us towards removing the bus custom operations.
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
All subdrivers use the irqdomain to demux AB8500 IRQs but here
in the hierarchical path we find a leftover instance using the
hard-coded IRQ base. Convert it to use irqdomain with a
oneliner.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
drivers/mfd/rtl8411.c: In function 'rtl8411_fetch_vendor_settings':
drivers/mfd/rtl8411.c:58:7: warning: 'reg1' is used uninitialized in this function [-Wuninitialized]
drivers/mfd/rtl8411.c: In function 'rtl8411b_fetch_vendor_settings':
drivers/mfd/rtl8411.c:79:7: warning: 'reg' is used uninitialized in this function [-Wuninitialized]
drivers/mfd/rtl8411.c: In function 'rtl8411_fetch_vendor_settings':
drivers/mfd/rtl8411.c:69:26: warning: 'reg3' may be used uninitialized in this function [-Wuninitialized]
Tested-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Opensource [Steve Twiss]