Add support for AMD PTDMA controller. It performs high-bandwidth
memory to memory and IO copy operation. Device commands are managed
via a circular queue of 'descriptors', each of which specifies source
and destination addresses for copying a single buffer of data.
Signed-off-by: Sanjay R Mehta <sanju.mehta@amd.com>
Link: https://lore.kernel.org/r/1629208559-51964-2-git-send-email-Sanju.Mehta@amd.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
DSA spec says WQ priv bit is 0 if the Privileged Mode Enable field of the
PCI Express PASID capability is 0 and pasid is enabled. Make sure that the
WQCFG priv field is set correctly according to usage type. Reject config if
setting up kernel WQ type and no support. Also add the correct priv setup
for a descriptor.
Fixes: 484f910e93 ("dmaengine: idxd: fix wq config registers offset programming")
Cc: Ramesh Thomas <ramesh.thomas@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/162939084657.903168.14160019185148244596.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Now that UML has PCI support, this driver must depend also on
!UML since it pokes at X86_64 architecture internals that don't
exist on ARCH=um.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/20210809112409.a3a0974874d2.I2ffe3d11ed37f735da2f39884a74c953b258b995@changeid
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The original architecture of /sys/bus/dsa invented a scheme whereby
a single entry in the list of bus drivers, /sys/bus/drivers/dsa,
handled all device types and internally routed them to different
different drivers. Those internal drivers were invisible to
userspace.
With the idxd driver transitioned to a proper bus device-driver model,
the legacy behavior needs to be preserved due to it being exposed to
user space via sysfs. Create a compat driver to provide the legacy
behavior for /sys/bus/dsa/drivers/dsa. This should satisfy user
tool accel-config v3.2 or ealier where this behavior is expected.
If the distro has a newer accel-config then the legacy mode does
not need to be enabled.
When the compat driver binds the device (i.e. dsa0) to the dsa driver,
it will be bound to the new idxd_drv. The wq device (i.e. wq0.0) will
be bound to either the dmaengine_drv or the user_drv. The dsa_drv
becomes a routing mechansim for the new drivers. It will not support
additional external drivers that are implemented later.
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/162637468705.744545.4399080971745974435.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In preparation for dsa_drv compat support to be built-in, move the bus
code to its own compilation unit. A follow-on patch adds the compat
implementation. Recall that the compat implementation allows for the
deprecated / omnibus dsa_drv binding scheme rather than the idiomatic
organization of a full fledged bus driver per driver type.
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/162637468142.744545.2811632736881720857.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Now that UML has PCI support, this driver must depend also on
!UML since it pokes at X86_64 architecture internals that don't
exist on ARCH=um.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Acked-By: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Link: https://lore.kernel.org/r/20210625103810.fe877ae0aef4.If240438e3f50ae226f3f755fc46ea498c6858393@changeid
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When CONFIG_HAS_IOMEM is not set/enabled, certain iomap() family
functions [including ioremap(), devm_ioremap(), etc.] are not
available.
Drivers that use these functions should depend on HAS_IOMEM so that
they do not cause build errors.
Repairs this build error:
s390-linux-ld: drivers/dma/altera-msgdma.o: in function `request_and_map':
altera-msgdma.c:(.text+0x14b0): undefined reference to `devm_ioremap'
Fixes: a85c6f1b29 ("dmaengine: Add driver for Altera / Intel mSGDMA IP core")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: dmaengine@vger.kernel.org
Reviewed-by: Stefan Roese <sr@denx.de>
Phone: (+49)-8142-66989-51 Fax: (+49)-8142-66989-80 Email: sr@denx.de
Link: https://lore.kernel.org/r/20210522021313.16405-2-rdunlap@infradead.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The driver depends on both OF and IOMEM support, express those
dependencies in Kconfig. This fixes a build failure on S390 reported by
the 0day bot.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Jianqiang Chen <jianqiang.chen@xilinx.com>
Reviewed-by: Jianqiang Chen <jianqiang.chen@xilinx.com>
Link: https://lore.kernel.org/r/20210520152420.23986-2-laurent.pinchart@ideasonboard.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
New drivers/devices
- Support for QCOM SM8150 GPI DMA
Updates:
- Big pile of idxd updates including support for performance monitoring
- Support in dw-edma for interleaved dma
- Support for synchronize() in Xilinx driver
-----BEGIN PGP SIGNATURE-----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=Jjb4
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine
Pull dmaengine updates from Vinod Koul:
"New drivers/devices:
- Support for QCOM SM8150 GPI DMA
Updates:
- Big pile of idxd updates including support for performance
monitoring
- Support in dw-edma for interleaved dma
- Support for synchronize() in Xilinx driver"
* tag 'dmaengine-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine: (42 commits)
dmaengine: idxd: Enable IDXD performance monitor support
dmaengine: idxd: Add IDXD performance monitor support
dmaengine: idxd: remove MSIX masking for interrupt handlers
dmaengine: idxd: device cmd should use dedicated lock
dmaengine: idxd: support reporting of halt interrupt
dmaengine: idxd: enable SVA feature for IOMMU
dmaengine: idxd: convert sprintf() to sysfs_emit() for all usages
dmaengine: idxd: add interrupt handle request and release support
dmaengine: idxd: add support for readonly config mode
dmaengine: idxd: add percpu_ref to descriptor submission path
dmaengine: idxd: remove detection of device type
dmaengine: idxd: iax bus removal
dmaengine: idxd: fix cdev setup and free device lifetime issues
dmaengine: idxd: fix group conf_dev lifetime
dmaengine: idxd: fix engine conf_dev lifetime
dmaengine: idxd: fix wq conf_dev 'struct device' lifetime
dmaengine: idxd: fix idxd conf_dev 'struct device' lifetime
dmaengine: idxd: use ida for device instance enumeration
dmaengine: idxd: removal of pcim managed mmio mapping
dmaengine: idxd: cleanup pci interrupt vector allocation management
...
Implement the IDXD performance monitor capability (named 'perfmon' in
the DSA (Data Streaming Accelerator) spec [1]), which supports the
collection of information about key events occurring during DSA and
IAX (Intel Analytics Accelerator) device execution, to assist in
performance tuning and debugging.
The idxd perfmon support is implemented as part of the IDXD driver and
interfaces with the Linux perf framework. It has several features in
common with the existing uncore pmu support:
- it does not support sampling
- does not support per-thread counting
However it also has some unique features not present in the core and
uncore support:
- all general-purpose counters are identical, thus no event constraints
- operation is always system-wide
While the core perf subsystem assumes that all counters are by default
per-cpu, the uncore pmus are socket-scoped and use a cpu mask to
restrict counting to one cpu from each socket. IDXD counters use a
similar strategy but expand the scope even further; since IDXD
counters are system-wide and can be read from any cpu, the IDXD perf
driver picks a single cpu to do the work (with cpu hotplug notifiers
to choose a different cpu if the chosen one is taken off-line).
More specifically, the perf userspace tool by default opens a counter
for each cpu for an event. However, if it finds a cpumask file
associated with the pmu under sysfs, as is the case with the uncore
pmus, it will open counters only on the cpus specified by the cpumask.
Since perfmon only needs to open a single counter per event for a
given IDXD device, the perfmon driver will create a sysfs cpumask file
for the device and insert the first cpu of the system into it. When a
user uses perf to open an event, perf will open a single counter on
the cpu specified by the cpu mask. This amounts to the default
system-wide rather than per-cpu counting mentioned previously for
perfmon pmu events. In order to keep the cpu mask up-to-date, the
driver implements cpu hotplug support for multiple devices, as IDXD
usually enumerates and registers more than one idxd device.
The perfmon driver implements basic perfmon hardware capability
discovery and configuration, and is initialized by the IDXD driver's
probe function. During initialization, the driver retrieves the total
number of supported performance counters, the pmu ID, and the device
type from idxd device, and registers itself under the Linux perf
framework.
The perf userspace tool can be used to monitor single or multiple
events depending on the given configuration, as well as event groups,
which are also supported by the perfmon driver. The user configures
events using the perf tool command-line interface by specifying the
event and corresponding event category, along with an optional set of
filters that can be used to restrict counting to specific work queues,
traffic classes, page and transfer sizes, and engines (See [1] for
specifics).
With the configuration specified by the user, the perf tool issues a
system call passing that information to the kernel, which uses it to
initialize the specified event(s). The event(s) are opened and
started, and following termination of the perf command, they're
stopped. At that point, the perfmon driver will read the latest count
for the event(s), calculate the difference between the latest counter
values and previously tracked counter values, and display the final
incremental count as the event count for the cycle. An overflow
handler registered on the IDXD irq path is used to account for counter
overflows, which are signaled by an overflow interrupt.
Below are a couple of examples of perf usage for monitoring DSA events.
The following monitors all events in the 'engine' category. Becuuse
no filters are specified, this captures all engine events for the
workload, which in this case is 19 iterations of the work generated by
the kernel dmatest module.
Details describing the events can be found in Appendix D of [1],
Performance Monitoring Events, but briefly they are:
event 0x1: total input data processed, in 32-byte units
event 0x2: total data written, in 32-byte units
event 0x4: number of work descriptors that read the source
event 0x8: number of work descriptors that write the destination
event 0x10: number of work descriptors dispatched from batch descriptors
event 0x20: number of work descriptors dispatched from work queues
# perf stat -e dsa0/event=0x1,event_category=0x1/,
dsa0/event=0x2,event_category=0x1/,
dsa0/event=0x4,event_category=0x1/,
dsa0/event=0x8,event_category=0x1/,
dsa0/event=0x10,event_category=0x1/,
dsa0/event=0x20,event_category=0x1/
modprobe dmatest channel=dma0chan0 timeout=2000
iterations=19 run=1 wait=1
Performance counter stats for 'system wide':
5,332 dsa0/event=0x1,event_category=0x1/
5,327 dsa0/event=0x2,event_category=0x1/
19 dsa0/event=0x4,event_category=0x1/
19 dsa0/event=0x8,event_category=0x1/
0 dsa0/event=0x10,event_category=0x1/
19 dsa0/event=0x20,event_category=0x1/
21.977436186 seconds time elapsed
The command below illustrates filter usage with a simple example. It
specifies that MEM_MOVE operations should be counted for the DSA
device dsa0 (event 0x8 corresponds to the EV_MEM_MOVE event - Number
of Memory Move Descriptors, which is part of event category 0x3 -
Operations. The detailed category and event IDs are available in
Appendix D, Performance Monitoring Events, of [1]). In addition to
the event and event category, a number of filters are also specified
(the detailed filter values are available in Chapter 6.4 (Filter
Support) of [1]), which will restrict counting to only those events
that meet all of the filter criteria. In this case, the filters
specify that only MEM_MOVE operations that are serviced by work queue
wq0 and specifically engine number engine0 and traffic class tc0
having sizes between 0 and 4k and page size of between 0 and 1G result
in a counter hit; anything else will be filtered out and not appear in
the final count. Note that filters are optional - any filter not
specified is assumed to be all ones and will pass anything.
# perf stat -e dsa0/filter_wq=0x1,filter_tc=0x1,filter_sz=0x7,
filter_eng=0x1,event=0x8,event_category=0x3/
modprobe dmatest channel=dma0chan0 timeout=2000
iterations=19 run=1 wait=1
Performance counter stats for 'system wide':
19 dsa0/filter_wq=0x1,filter_tc=0x1,filter_sz=0x7,
filter_eng=0x1,event=0x8,event_category=0x3/
21.865914091 seconds time elapsed
The output above reflects that the unspecified workload resulted in
the counting of 19 MEM_MOVE operation events that met the filter
criteria.
[1]: https://software.intel.com/content/www/us/en/develop/download/intel-data-streaming-accelerator-preliminary-architecture-specification.html
[ Based on work originally by Jing Lin. ]
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Tom Zanussi <tom.zanussi@linux.intel.com>
Link: https://lore.kernel.org/r/0c5080a7d541904c4ad42b848c76a1ce056ddac7.1619276133.git.zanussi@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
ARCH_SOCFPGA is being renamed to ARCH_INTEL_SOCFPGA so adjust the
32-bit ARM drivers to rely on new symbol.
Acked-By: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
The zte zx platform is getting removed, so this driver is no
longer needed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Jun Nie <jun.nie@linaro.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Link: https://lore.kernel.org/r/20210120131859.2056308-3-arnd@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The CSR SiRF prima2/atlas platforms are getting removed, so this driver
is no longer needed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Barry Song <baohua@kernel.org>
Cc: Barry Song <baohua@kernel.org>
Link: https://lore.kernel.org/r/20210120131859.2056308-2-arnd@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add DMA controller driver for Lightning Mountain (LGM) family of SoCs.
The main function of the DMA controller is the transfer of data from/to any
peripheral to/from the memory. A memory to memory copy capability can also
be configured.
This ldma driver is used for configure the device and channnels for data
and control paths.
Signed-off-by: Amireddy Mallikarjuna reddy <mallikarjunax.reddy@linux.intel.com>
Link: https://lore.kernel.org/r/5fc54eb7ccfad4f8dd812b66b884054fc55cf050.1606905330.git.mallikarjunax.reddy@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
New drivers/devices
- Qualcomm ADM driver
- Qualcomm GPI driver
- Allwinner A100 DMA support
- Microchip Sama7g5 support
- Mediatek MT8516 apdma
- Updates:
- more updates to idxd driver and support for IAX config
- runtime PM support for dw driver
- TI keystone drivers for 5.11 included here due to dependency for TI
drivers
-----BEGIN PGP SIGNATURE-----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=uNBn
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine
Pull dmaengine updates from Vinod Koul:
"The last dmaengine updates for this year :)
This contains couple of new drivers, new device support and updates to
bunch of drivers.
New drivers/devices:
- Qualcomm ADM driver
- Qualcomm GPI driver
- Allwinner A100 DMA support
- Microchip Sama7g5 support
- Mediatek MT8516 apdma
Updates:
- more updates to idxd driver and support for IAX config
- runtime PM support for dw driver
- TI drivers"
* tag 'dmaengine-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine: (75 commits)
soc: ti: k3-ringacc: Use correct error casting in k3_ringacc_dmarings_init
dmaengine: ti: k3-udma-glue: Add support for K3 PKTDMA
dmaengine: ti: k3-udma: Initial support for K3 PKTDMA
dmaengine: ti: k3-udma: Add support for BCDMA channel TPL handling
dmaengine: ti: k3-udma: Initial support for K3 BCDMA
soc: ti: k3-ringacc: add AM64 DMA rings support.
dmaengine: ti: Add support for k3 event routers
dmaengine: ti: k3-psil: Add initial map for AM64
dmaengine: ti: k3-psil: Extend psil_endpoint_config for K3 PKTDMA
dt-bindings: dma: ti: Add document for K3 PKTDMA
dt-bindings: dma: ti: Add document for K3 BCDMA
dmaengine: dmatest: Use dmaengine_get_dma_device
dmaengine: doc: client: Update for dmaengine_get_dma_device() usage
dmaengine: Add support for per channel coherency handling
dmaengine: of-dma: Add support for optional router configuration callback
dmaengine: ti: k3-udma-glue: Configure the dma_dev for rings
dmaengine: ti: k3-udma-glue: Get the ringacc from udma_dev
dmaengine: ti: k3-udma-glue: Add function to get device pointer for DMA API
dmaengine: ti: k3-udma: Add support for second resource range from sysfw
dmaengine: ti: k3-udma: Wait for peer teardown completion if supported
...
Add shared workqueue support that includes the support of Shared Virtual
memory (SVM) or in similar terms On Demand Paging (ODP). The shared
workqueue uses the enqcmds command in kernel and will respond with retry if
the workqueue is full. Shared workqueue only works when there is PASID
support from the IOMMU.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Link: https://lore.kernel.org/r/160382007499.3911367.26043087963708134.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This patch removes the MIC drivers from the kernel tree
since the corresponding devices have been discontinued.
Removing the dma and char-misc changes in one patch and
merging via the char-misc tree is best to avoid any
potential build breakage.
Cc: Nikhil Rao <nikhil.rao@intel.com>
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Sudeep Dutt <sudeep.dutt@intel.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/8c1443136563de34699d2c084df478181c205db4.1603854416.git.sudeep.dutt@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ZynqMP DisplayPort subsystem includes a DMA engine called DPDMA with
6 DMa channels (4 for display and 2 for audio). This driver exposes the
DPDMA through the dmaengine API, to be used by audio (ALSA) and display
(DRM) drivers for the DisplayPort subsystem.
Signed-off-by: Hyun Kwon <hyun.kwon@xilinx.com>
Signed-off-by: Tejas Upadhyay <tejasu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20200717013337.24122-4-laurent.pinchart@ideasonboard.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Fix build errors when CONFIG_PCI_MSI is not enabled by making the
driver depend on PCI_MSI:
ld: drivers/dma/idxd/device.o: in function `idxd_mask_msix_vector':
device.c:(.text+0x26f): undefined reference to `pci_msi_mask_irq'
ld: drivers/dma/idxd/device.o: in function `idxd_unmask_msix_vector':
device.c:(.text+0x2af): undefined reference to `pci_msi_unmask_irq'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: dmaengine@vger.kernel.org
Cc: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/9dee3f46-70d9-ea75-10cb-5527ab297d1d@infradead.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Bunch of updates to drivers like dmatest, dw-edma, ioat,
mmp-tdma and k3-udma along with Renesas binding update to json-schema
-----BEGIN PGP SIGNATURE-----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=Jun4
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-5.8-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"A fairly small dmaengine update which includes mostly driver updates
(dmatest, dw-edma, ioat, mmp-tdma and k3-udma) along with Renesas
binding update to json-schema"
* tag 'dmaengine-5.8-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (39 commits)
dmaengine: imx-sdma: initialize all script addresses
dmaengine: ti: k3-udma: Use proper return code in alloc_chan_resources
dmaengine: ti: k3-udma: Remove udma_chan.in_ring_cnt
dmaengine: ti: k3-udma: Add missing dma_sync call for rx flush descriptor
dmaengine: at_xdmac: Replace zero-length array with flexible-array
dmaengine: at_hdmac: Replace zero-length array with flexible-array
dmaengine: qcom: bam_dma: Replace zero-length array with flexible-array
dmaengine: ti: k3-udma: Use PTR_ERR_OR_ZERO() to simplify code
dmaengine: moxart-dma: Drop pointless static qualifier in moxart_probe()
dmaengine: sf-pdma: Simplify the error handling path in 'sf_pdma_probe()'
dmaengine: qcom_hidma: use true,false for bool variable
dmaengine: dw-edma: support local dma device transfer semantics
dmaengine: Fix doc strings to satisfy validation script
dmaengine: Include dmaengine.h into dmaengine.c
dmaengine: dmatest: Describe members of struct dmatest_info
dmaengine: dmatest: Describe members of struct dmatest_params
dmaengine: dmatest: Allow negative timeout value to specify infinite wait
Revert "dmaengine: dmatest: timeout value of -1 should specify infinite wait"
dmaengine: stm32-dma: direct mode support through device tree
dt-bindings: dma: add direct mode support through device tree in stm32-dma
...
A generic SRAM will driver for Device Tree enabled platforms will do as
well.
The non-DT drivers that use mmp_tdma to transfer audio samples to and from
the audio SRAM should depend on MMP_SRAM themselves.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Link: https://lore.kernel.org/r/20200419164912.670973-8-lkundrak@v3.sk
Signed-off-by: Vinod Koul <vkoul@kernel.org>
If PCI_MSI is not set, building fais:
drivers/dma/hisi_dma.c: In function ‘hisi_dma_free_irq_vectors’:
drivers/dma/hisi_dma.c:138:2: error: implicit declaration of function ‘pci_free_irq_vectors’;
did you mean ‘pci_alloc_irq_vectors’? [-Werror=implicit-function-declaration]
pci_free_irq_vectors(data);
^~~~~~~~~~~~~~~~~~~~
Make HISI_DMA depends on PCI_MSI to fix this.
Fixes: e9f08b6525 ("dmaengine: hisilicon: Add Kunpeng DMA engine support")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20200328114133.17560-1-yuehaibing@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This adds external DMA controller driver implemented in Socionext
UniPhier SoCs. This driver supports DMA_MEMCPY and DMA_SLAVE modes.
Since this driver does not support the the way to transfer size
unaligned to burst width, 'src_maxburst' or 'dst_maxburst' of
dma_slave_config must be 1 to transfer arbitrary size. If transfer
size is unaligned to burst size, the transfer isn't started and
the driver displays an error message.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/1582271550-3403-3-git-send-email-hayashi.kunihiko@socionext.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There is nothing arch-specific in the driver's code, so let's enable
compile-testing for the driver.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20200209163356.6439-18-digetx@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The driver's removal was fixed by a recent commit and module load/unload
is working well now, tested on Tegra30.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20200209163356.6439-16-digetx@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This patch adds a driver for HiSilicon Kunpeng DMA engine. This DMA engine
which is an PCIe iEP offers 30 channels, each channel has a send queue, a
complete queue and an interrupt to help to do tasks. This DMA engine can do
memory copy between memory blocks or between memory and device buffer.
Signed-off-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Zhenfa Qiu <qiuzhenfa@hisilicon.com>
Link: https://lore.kernel.org/r/1579155057-80523-1-git-send-email-wangzhou1@hisilicon.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The idxd driver introduces the Intel Data Stream Accelerator [1] that will
be available on future Intel Xeon CPUs. One of the kernel access
point for the driver is through the dmaengine subsystem. It will initially
provide the DMA copy service to the kernel.
Some of the main functionality introduced with this accelerator
are: shared virtual memory (SVM) support, and descriptor submission using
Intel CPU instructions movdir64b and enqcmds. There will be additional
accelerator devices that share the same driver with variations to
capabilities.
This commit introduces the probe and initialization component of the
driver.
[1]: https://software.intel.com/en-us/download/intel-data-streaming-accelerator-preliminary-architecture-specification
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/157965023991.73301.6186843973135311580.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Some PLX Switches can expose DMA engines via extra PCI functions
on the upstream port. Each function will have one DMA channel.
This patch is just the core PCI driver skeleton and dma
engine registration.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Link: https://lore.kernel.org/r/20200103212021.2881-2-logang@deltatee.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/1574306348-29212-1-git-send-email-krzk@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support for AXI Multichannel Direct Memory Access (AXI MCDMA)
core, which is a soft Xilinx IP core that provides high-bandwidth
direct memory access between memory and AXI4-Stream target peripherals.
The AXI MCDMA core provides scatter-gather interface with multiple
independent transmit and receive channels. The driver supports
device_prep_slave_sg slave transfer mode.
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Link: https://lore.kernel.org/r/1571763622-29281-7-git-send-email-radhey.shyam.pandey@xilinx.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Driver for Socionext Milbeaut HDMAC controller. The controller has
upto 8 floating channels, that need a predefined slave-id to work
from a set of slaves.
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Link: https://lore.kernel.org/r/20191015033359.14925-1-jassisinghbrar@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
DPPA2(Data Path Acceleration Architecture 2) qDMA supports
virtualized channel by allowing DMA jobs to be enqueued into
different work queues. Core can initiate a DMA transaction by
preparing a frame descriptor(FD) for each DMA job and enqueuing
this job through a hardware portal. DPAA2 components can also
prepare a FD and enqueue a DMA job through a hardware portal.
The qDMA prefetches DMA jobs through DPAA2 hardware portal. It
then schedules and dispatches to internal DMA hardware engines,
which generate read and write requests. Both qDMA source data and
destination data can be either contiguous or non-contiguous using
one or more scatter/gather tables.
The qDMA supports global bandwidth flow control where all DMA
transactions are stalled if the bandwidth threshold has been reached.
Also supported are transaction based read throttling.
Add NXP dppa2 qDMA to support some of Layerscape SoCs.
such as: LS1088A, LS208xA, LX2, etc.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Link: https://lore.kernel.org/r/20190930020440.7754-2-peng.ma@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
- boot_mem_map is removed, providing a nice cleanup made possible by the
recent removal of bootmem.
- Some fixes to atomics, in general providing compiler barriers for
smp_mb__{before,after}_atomic plus fixes specific to Loongson CPUs or
MIPS32 systems using cmpxchg64().
- Conversion to the new generic VDSO infrastructure courtesy of Vincenzo
Frascino.
- Removal of undefined behavior in set_io_port_base(), fixing the
behavior of some MIPS kernel configurations when built with recent
clang versions.
- Initial MIPS32 huge page support, functional on at least Ingenic SoCs.
- pte_special() is now supported for some configurations, allowing among
other things generic fast GUP to be used.
- Miscellaneous fixes & cleanups.
And platform specific changes:
- Major improvements to Ingenic SoC support from Paul Cercueil, mostly
enabled by the inclusion of the new TCU (timer-counter unit) drivers
he's spent a very patient year or so working on. Plus some fixes for
X1000 SoCs from Zhou Yanjie.
- Netgear R6200 v1 systems are now supported by the bcm47xx platform.
- DT updates for BMIPS, Lantiq & Microsemi Ocelot systems.
-----BEGIN PGP SIGNATURE-----
iIsEABYIADMWIQRgLjeFAZEXQzy86/s+p5+stXUA3QUCXYaqpRUccGF1bC5idXJ0
b25AbWlwcy5jb20ACgkQPqefrLV1AN2JUQD+PQGFIlq9bo/3vLyqsXJffm+DhwVQ
4WSCSeN5brPkO8EA/153sRJBlRtG+KK5p9f7WYKUuBfbcEawuc1uwmKuy7cG
=lWlM
-----END PGP SIGNATURE-----
Merge tag 'mips_5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Paul Burton:
"Main MIPS changes:
- boot_mem_map is removed, providing a nice cleanup made possible by
the recent removal of bootmem.
- Some fixes to atomics, in general providing compiler barriers for
smp_mb__{before,after}_atomic plus fixes specific to Loongson CPUs
or MIPS32 systems using cmpxchg64().
- Conversion to the new generic VDSO infrastructure courtesy of
Vincenzo Frascino.
- Removal of undefined behavior in set_io_port_base(), fixing the
behavior of some MIPS kernel configurations when built with recent
clang versions.
- Initial MIPS32 huge page support, functional on at least Ingenic
SoCs.
- pte_special() is now supported for some configurations, allowing
among other things generic fast GUP to be used.
- Miscellaneous fixes & cleanups.
And platform specific changes:
- Major improvements to Ingenic SoC support from Paul Cercueil,
mostly enabled by the inclusion of the new TCU (timer-counter unit)
drivers he's spent a very patient year or so working on. Plus some
fixes for X1000 SoCs from Zhou Yanjie.
- Netgear R6200 v1 systems are now supported by the bcm47xx platform.
- DT updates for BMIPS, Lantiq & Microsemi Ocelot systems"
* tag 'mips_5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (89 commits)
MIPS: Detect bad _PFN_SHIFT values
MIPS: Disable pte_special() for MIPS32 with RiXi
MIPS: ralink: deactivate PCI support for SOC_MT7621
mips: compat: vdso: Use legacy syscalls as fallback
MIPS: Drop Loongson _CACHE_* definitions
MIPS: tlbex: Remove cpu_has_local_ebase
MIPS: tlbex: Simplify r3k check
MIPS: Select R3k-style TLB in Kconfig
MIPS: PCI: refactor ioc3 special handling
mips: remove ioremap_cachable
mips/atomic: Fix smp_mb__{before,after}_atomic()
mips/atomic: Fix loongson_llsc_mb() wreckage
mips/atomic: Fix cmpxchg64 barriers
MIPS: Octeon: remove duplicated include from dma-octeon.c
firmware: bcm47xx_nvram: Allow COMPILE_TEST
firmware: bcm47xx_nvram: Correct size_t printf format
MIPS: Treat Loongson Extensions as ASEs
MIPS: Remove dev_err() usage after platform_get_irq()
MIPS: dts: mscc: describe the PTP ready interrupt
MIPS: dts: mscc: describe the PTP register range
...
- Move Dmaengine DT bindings to YAML and convert Allwinner to schema.
- FSL dma device_synchronize implementation
- DW split acpi and of helpers and updates to driver and support for Elkhart
Lake
- Move filter fn as private for omap-dma and edma drivers and improvements
to these drivers
- Mark expected switch fall-through in couple of drivers
- Renames of shdma and nbpfaxi binding document
- Minor updates to bunch of drivers
-----BEGIN PGP SIGNATURE-----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=Q8bz
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-5.4-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
- Move Dmaengine DT bindings to YAML and convert Allwinner to schema.
- FSL dma device_synchronize implementation
- DW split acpi and of helpers and updates to driver and support for
Elkhart Lake
- Move filter fn as private for omap-dma and edma drivers and
improvements to these drivers
- Mark expected switch fall-through in couple of drivers
- Renames of shdma and nbpfaxi binding document
- Minor updates to bunch of drivers
* tag 'dmaengine-5.4-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (55 commits)
dmaengine: ti: edma: Use bitmap_set() instead of open coded edma_set_bits()
dmaengine: ti: edma: Only reset region0 access registers
dmaengine: ti: edma: Do not reset reserved paRAM slots
dmaengine: iop-adma.c: fix printk format warning
dmaengine: stm32-dma: Use struct_size() helper
dt-bindings: dmaengine: dma-common: Fix the dma-channel-mask property
dmanegine: ioat/dca: Use struct_size() helper
dmaengine: iop-adma: remove set but not used variable 'slots_per_op'
dmaengine: dmatest: Add support for completion polling
dmaengine: ti: omap-dma: Remove variable override in omap_dma_tx_status()
dmaengine: ti: omap-dma: Remove 'Assignment in if condition'
dmaengine: ti: edma: Remove 'Assignment in if condition'
dmaengine: dw: platform: Split OF helpers to separate module
dmaengine: dw: platform: Split ACPI helpers to separate module
dmaengine: dw: platform: Move handle check to dw_dma_acpi_controller_register()
dmaengine: dw: platform: Switch to acpi_dma_controller_register()
dmaengine: dw: platform: Use devm_platform_ioremap_resource()
dmaengine: dw: platform: Enable iDMA 32-bit on Intel Elkhart Lake
dmaengine: dw: platform: Use struct dw_dma_chip_pdata
dmaengine: dw: Export struct dw_dma_chip_pdata for wider use
...
The main change this time around is a cleanup of some of the oldest
platforms based on the XScale and ARM9 CPU cores, which are between 10
and 20 years old.
The Kendin/Micrel/Microchip KS8695, Winbond/Nuvoton W90x900 and Intel
IOP33x/IOP13xx platforms are removed after we determined that nobody is
using them any more.
The TI Davinci and NXP LPC32xx platforms on the other hand are still in
active use and are converted to the ARCH_MULTIPLATFORM build, meaning
that we can compile a kernel that works on these along with most other
ARMv5 platforms. Changes toward that goal are also merged for IOP32x,
but additional work is needed to complete this. Patches for the
remaining ARMv5 platforms have started but need more work and some
testing.
Support for the new ASpeed AST2600 gets added, this is based on the
Cortex-A7 ARMv7 core, and is a newer version of the existing ARMv5 and
ARMv6 chips in the same family.
Other changes include a cleanup of the ST-Ericsson ux500 platform
and the move of the TI Davinci platform to a new clocksource driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=u+ew
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Arnd Bergmann:
"The main change this time around is a cleanup of some of the oldest
platforms based on the XScale and ARM9 CPU cores, which are between 10
and 20 years old.
The Kendin/Micrel/Microchip KS8695, Winbond/Nuvoton W90x900 and Intel
IOP33x/IOP13xx platforms are removed after we determined that nobody
is using them any more.
The TI Davinci and NXP LPC32xx platforms on the other hand are still
in active use and are converted to the ARCH_MULTIPLATFORM build,
meaning that we can compile a kernel that works on these along with
most other ARMv5 platforms. Changes toward that goal are also merged
for IOP32x, but additional work is needed to complete this. Patches
for the remaining ARMv5 platforms have started but need more work and
some testing.
Support for the new ASpeed AST2600 gets added, this is based on the
Cortex-A7 ARMv7 core, and is a newer version of the existing ARMv5 and
ARMv6 chips in the same family.
Other changes include a cleanup of the ST-Ericsson ux500 platform and
the move of the TI Davinci platform to a new clocksource driver"
[ The changes had marked INTEL_IOP_ADMA and USB_LPC32XX as being
buildable on other platforms through COMPILE_TEST, but that causes new
warnings that I most definitely do not want to see during the merge
window as that could hide other issues.
So the COMPILE_TEST option got disabled for them again - Linus ]
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (61 commits)
ARM: multi_v5_defconfig: make DaVinci part of the ARM v5 multiplatform build
ARM: davinci: support multiplatform build for ARM v5
arm64: exynos: Enable exynos-chipid driver
ARM: OMAP2+: Delete an unnecessary kfree() call in omap_hsmmc_pdata_init()
ARM: OMAP2+: move platform-specific asm-offset.h to arch/arm/mach-omap2
ARM: davinci: dm646x: Fix a typo in the comment
ARM: davinci: dm646x: switch to using the clocksource driver
ARM: davinci: dm644x: switch to using the clocksource driver
ARM: aspeed: Enable SMP boot
ARM: aspeed: Add ASPEED AST2600 architecture
ARM: aspeed: Select timer in each SoC
dt-bindings: arm: cpus: Add ASPEED SMP
ARM: imx: stop adjusting ar8031 phy tx delay
mailmap: map old company name to new one @microchip.com
MAINTAINERS: at91: remove the TC entry
MAINTAINERS: at91: Collect all pinctrl/gpio drivers in same entry
ARM: at91: move platform-specific asm-offset.h to arch/arm/mach-at91
MAINTAINERS: Extend patterns for Samsung SoC, Security Subsystem and clock drivers
ARM: s3c64xx: squash samsung_usb_phy.h into setup-usb-phy.c
ARM: debug-ll: Add support for r7s9210
...
Now that iop3xx and iop13xx are gone, the iop-adma driver no
longer needs to deal with incompatible register layout defined
in machine specific header files.
Move the iop32x specific definitions into drivers/dma/iop-adma.h
and the platform_data into include/linux/platform_data/dma-iop32x.h,
and change the machine code to no longer reference those.
The DMA0_ID/DMA1_ID/AAU_ID macros are required as part of the
platform data interface and still need to be visible, so move
those from one header to the other.
Link: https://lore.kernel.org/r/20190809163334.489360-4-arnd@arndb.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
There are three families of IOP machines we support in Linux: iop32x
(which includes EP80219), iop33x and iop13xx (aka IOP34x aka WP8134x).
All products we support in the kernel are based on the first of these,
iop32x, the other families only ever supported the Intel reference
boards but no actual machine anyone could ever buy.
While one could clearly make them all three work in a single kernel
with some work, this takes the easy way out, removing the later two
platforms entirely, under the assumption that there are no remaining
users.
Earlier versions of OpenWRT and Debian both had support for iop32x
but not the others, and they both dropped iop32x as well in their 2015
releases.
Link: https://lore.kernel.org/r/20190809163334.489360-1-arnd@arndb.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Wolfram Sang <wsa@the-dreams.de> # for I2C parts
Acked-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The newer and better JZ4780 driver is now used to provide DMA
functionality on the JZ4740.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
- Add support in dmaengine core to do device node checks for DT devices and
update bunch of drivers to use that and remove open coding from drivers
- New driver/driver support for new hardware, namely:
- MediaTek UART APDMA
- Freescale i.mx7ulp edma2
- Synopsys eDMA IP core version 0
- Allwinner H6 DMA
- Updates to axi-dma and support for interleaved cyclic transfers
- Greg's debugfs return value check removals on drivers
- Updates to stm32-dma, hsu, dw, pl330, tegra drivers
-----BEGIN PGP SIGNATURE-----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=R+aC
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-5.3-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
- Add support in dmaengine core to do device node checks for DT devices
and update bunch of drivers to use that and remove open coding from
drivers
- New driver/driver support for new hardware, namely:
- MediaTek UART APDMA
- Freescale i.mx7ulp edma2
- Synopsys eDMA IP core version 0
- Allwinner H6 DMA
- Updates to axi-dma and support for interleaved cyclic transfers
- Greg's debugfs return value check removals on drivers
- Updates to stm32-dma, hsu, dw, pl330, tegra drivers
* tag 'dmaengine-5.3-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (68 commits)
dmaengine: Revert "dmaengine: fsl-edma: add i.mx7ulp edma2 version support"
dmaengine: at_xdmac: check for non-empty xfers_list before invoking callback
Documentation: dmaengine: clean up description of dmatest usage
dmaengine: tegra210-adma: remove PM_CLK dependency
dmaengine: fsl-edma: add i.mx7ulp edma2 version support
dt-bindings: dma: fsl-edma: add new i.mx7ulp-edma
dmaengine: fsl-edma-common: version check for v2 instead
dmaengine: fsl-edma-common: move dmamux register to another single function
dmaengine: fsl-edma: add drvdata for fsl-edma
dmaengine: Revert "dmaengine: fsl-edma: support little endian for edma driver"
dmaengine: rcar-dmac: Reject zero-length slave DMA requests
dmaengine: dw: Enable iDMA 32-bit on Intel Elkhart Lake
dmaengine: dw-edma: fix semicolon.cocci warnings
dmaengine: sh: usb-dmac: Use [] to denote a flexible array member
dmaengine: dmatest: timeout value of -1 should specify infinite wait
dmaengine: dw: Distinguish ->remove() between DW and iDMA 32-bit
dmaengine: fsl-edma: support little endian for edma driver
dmaengine: hsu: Revert "set HSU_CH_MTSR to memory width"
dmagengine: pl330: add code to get reset property
dt-bindings: pl330: document the optional resets property
...
Tegra ADMA does not use pm-clk interface now and hence the dependency
is removed from Kconfig.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Sanjay R Mehta