This patch introduces in-kernel handling of some intercepts for privileged
instructions:
handle_set_prefix() sets the prefix register of the local cpu
handle_store_prefix() stores the content of the prefix register to memory
handle_store_cpu_address() stores the cpu number of the current cpu to memory
handle_skey() just decrements the instruction address and retries
handle_stsch() delivers condition code 3 "operation not supported"
handle_chsc() same here
handle_stfl() stores the facility list which contains the
capabilities of the cpu
handle_stidp() stores cpu type/model/revision and such
handle_stsi() stores information about the system topology
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch contains the s390 interrupt subsystem (similar to in kernel apic)
including timer interrupts (similar to in-kernel-pit) and enabled wait
(similar to in kernel hlt).
In order to achieve that, this patch also introduces intercept handling
for instruction intercepts, and it implements load control instructions.
This patch introduces an ioctl KVM_S390_INTERRUPT which is valid for both
the vm file descriptors and the vcpu file descriptors. In case this ioctl is
issued against a vm file descriptor, the interrupt is considered floating.
Floating interrupts may be delivered to any virtual cpu in the configuration.
The following interrupts are supported:
SIGP STOP - interprocessor signal that stops a remote cpu
SIGP SET PREFIX - interprocessor signal that sets the prefix register of a
(stopped) remote cpu
INT EMERGENCY - interprocessor interrupt, usually used to signal need_reshed
and for smp_call_function() in the guest.
PROGRAM INT - exception during program execution such as page fault, illegal
instruction and friends
RESTART - interprocessor signal that starts a stopped cpu
INT VIRTIO - floating interrupt for virtio signalisation
INT SERVICE - floating interrupt for signalisations from the system
service processor
struct kvm_s390_interrupt, which is submitted as ioctl parameter when injecting
an interrupt, also carrys parameter data for interrupts along with the interrupt
type. Interrupts on s390 usually have a state that represents the current
operation, or identifies which device has caused the interruption on s390.
kvm_s390_handle_wait() does handle waitpsw in two flavors: in case of a
disabled wait (that is, disabled for interrupts), we exit to userspace. In case
of an enabled wait we set up a timer that equals the cpu clock comparator value
and sleep on a wait queue.
[christian: change virtio interrupt to 0x2603]
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This path introduces handling of sie intercepts in three flavors: Intercepts
are either handled completely in-kernel by kvm_handle_sie_intercept(),
or passed to userspace with corresponding data in struct kvm_run in case
kvm_handle_sie_intercept() returns -ENOTSUPP.
In case of partial execution in kernel with the need of userspace support,
kvm_handle_sie_intercept() may choose to set up struct kvm_run and return
-EREMOTE.
The trivial intercept reasons are handled in this patch:
handle_noop() just does nothing for intercepts that don't require our support
at all
handle_stop() is called when a cpu enters stopped state, and it drops out to
userland after updating our vcpu state
handle_validity() faults in the cpu lowcore if needed, or passes the request
to userland
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch contains the port of Qumranet's kvm kernel module to IBM zSeries
(aka s390x, mainframe) architecture. It uses the mainframe's virtualization
instruction SIE to run virtual machines with up to 64 virtual CPUs each.
This port is only usable on 64bit host kernels, and can only run 64bit guest
kernels. However, running 31bit applications in guest userspace is possible.
The following source files are introduced by this patch
arch/s390/kvm/kvm-s390.c similar to arch/x86/kvm/x86.c, this implements all
arch callbacks for kvm. __vcpu_run calls back into
sie64a to enter the guest machine context
arch/s390/kvm/sie64a.S assembler function sie64a, which enters guest
context via SIE, and switches world before and after that
include/asm-s390/kvm_host.h contains all vital data structures needed to run
virtual machines on the mainframe
include/asm-s390/kvm.h defines kvm_regs and friends for user access to
guest register content
arch/s390/kvm/gaccess.h functions similar to uaccess to access guest memory
arch/s390/kvm/kvm-s390.h header file for kvm-s390 internals, extended by
later patches
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Christian Borntraeger