On ACPI ARM based systems the GIC interrupt controller
and corresponding interrupt model permit only the high
polarity for level interrupts.
ACPI firmware describes PCI legacy IRQs through entries
in the _PRT objects. Entries in the _PRT can be of two types:
- Static: not configurable, trigger/polarity default to level-low,
_PRT entry defines the global GSI interrupt number
- Configurable: _PRT interrupt entry contains a reference to the
corresponding PCI interrupt link device (that in turn provides the
interrupt descriptor through its _CRS/_PRS methods)
Configurable IRQ entries are not currently allowed by the ACPI
specification on ARM since they can only be used for interrupt pins that
are routable, as per ACPI specifications (version 6.1, 6.2.13):
"[...] There are two ways that _PRT can be used. Typically, the
interrupt input that a given PCI interrupt is on is configurable. For
example, a given PCI interrupt might be configured for either IRQ 10 or
11 on an 8259 interrupt controller. In this model, each interrupt is
represented in the ACPI namespace as a PCI Interrupt Link Device. [...]"
ARM platforms GIC configurations do not allow dynamic IRQ routing,
since routing is statically laid out at synthesis time; therefore PCI
interrupt links cannot be used for PCI legacy IRQ descriptions in the
_PRT on ARM systems.
On the other hand, current core ACPI code handling PCI legacy IRQs
consider IRQ trigger/polarity for static _PRT entries as level-low.
On ARM systems with a GIC interrupt controller and corresponding
ACPI interrupt model this does not work in that GIC interrupt
controller is only capable of handling level interrupts whose
polarity is high (for PCI legacy IRQs - that are level-low by
specification - this means that the legacy IRQs are inverted before
reaching the interrupt controller pin), resulting in IRQ allocation
failures such as:
genirq: Setting trigger mode 8 for irq 18 failed (gic_set_type+0x0/0x48)
Change the default polarity for PCI legacy IRQs to high on systems
booting wth ACPI on platforms with a GIC interrupt controller model,
fixing the discrepancy between specification and HW behaviour.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Duc Dang <dhdang@apm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Per the x86-specific footnote to PCI spec r3.0, sec 6.2.4, the value 255 in
the Interrupt Line register means "unknown" or "no connection."
Previously, when we couldn't derive an IRQ from the _PRT, we fell back to
using the value from Interrupt Line as an IRQ. It's questionable whether
we should do that at all, but the spec clearly suggests we shouldn't do it
for the value 255 on x86.
Calling request_irq() with IRQ 255 may succeed, but the driver won't
receive any interrupts. Or, if IRQ 255 is shared with another device, it
may succeed, and the driver's ISR will be called at random times when the
*other* device interrupts. Or it may fail if another device is using IRQ
255 with incompatible flags. What we *want* is for request_irq() to fail
predictably so the driver can fall back to polling.
On x86, assume 255 in the Interrupt Line means the INTx line is not
connected. In that case, set dev->irq to IRQ_NOTCONNECTED so request_irq()
will fail gracefully with -ENOTCONN.
We found this problem on a system where Secure Boot firmware assigned
Interrupt Line 255 to an i801_smbus device and another device was already
using MSI-X IRQ 255. This was in v3.10, where i801_probe() fails if
request_irq() fails:
i801_smbus 0000:00:1f.3: enabling device (0140 -> 0143)
i801_smbus 0000:00:1f.3: can't derive routing for PCI INT C
i801_smbus 0000:00:1f.3: PCI INT C: no GSI
genirq: Flags mismatch irq 255. 00000080 (i801_smbus) vs. 00000000 (megasa)
CPU: 0 PID: 2487 Comm: kworker/0:1 Not tainted 3.10.0-229.el7.x86_64 #1
Hardware name: FUJITSU PRIMEQUEST 2800E2/D3736, BIOS PRIMEQUEST 2000 Serie5
Call Trace:
dump_stack+0x19/0x1b
__setup_irq+0x54a/0x570
request_threaded_irq+0xcc/0x170
i801_probe+0x32f/0x508 [i2c_i801]
local_pci_probe+0x45/0xa0
i801_smbus 0000:00:1f.3: Failed to allocate irq 255: -16
i801_smbus: probe of 0000:00:1f.3 failed with error -16
After aeb8a3d16a ("i2c: i801: Check if interrupts are disabled"),
i801_probe() will fall back to polling if request_irq() fails. But we
still need this patch because request_irq() may succeed or fail depending
on other devices in the system. If request_irq() fails, i801_smbus will
work by falling back to polling, but if it succeeds, i801_smbus won't work
because it expects interrupts that it may not receive.
Signed-off-by: Chen Fan <chen.fan.fnst@cn.fujitsu.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
991de2e590 ("PCI, x86: Implement pcibios_alloc_irq() and
pcibios_free_irq()") appeared in v4.3 and helps support IOAPIC hotplug.
Олег reported that the Elcus-1553 TA1-PCI driver worked in v4.2 but not
v4.3 and bisected it to 991de2e590. Sunjin reported that the RocketRAID
272x driver worked in v4.2 but not v4.3. In both cases booting with
"pci=routirq" is a workaround.
I think the problem is that after 991de2e590, we no longer call
pcibios_enable_irq() for upstream bridges. Prior to 991de2e590, when a
driver called pci_enable_device(), we recursively called
pcibios_enable_irq() for upstream bridges via pci_enable_bridge().
After 991de2e590, we call pcibios_enable_irq() from pci_device_probe()
instead of the pci_enable_device() path, which does *not* call
pcibios_enable_irq() for upstream bridges.
Revert 991de2e590 to fix these driver regressions.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=111211
Fixes: 991de2e590 ("PCI, x86: Implement pcibios_alloc_irq() and pcibios_free_irq()")
Reported-and-tested-by: Олег Мороз <oleg.moroz@mcc.vniiem.ru>
Reported-by: Sunjin Yang <fan4326@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
CC: Jiang Liu <jiang.liu@linux.intel.com>
Revert 811a4e6fce ("PCI: Add helpers to manage pci_dev->irq and
pci_dev->irq_managed").
This is part of reverting 991de2e590 ("PCI, x86: Implement
pcibios_alloc_irq() and pcibios_free_irq()") to fix regressions it
introduced.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=111211
Fixes: 991de2e590 ("PCI, x86: Implement pcibios_alloc_irq() and pcibios_free_irq()")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
CC: Jiang Liu <jiang.liu@linux.intel.com>
source is decleared as a 4 byte char array in struct acpi_pci_routing_table
so !prt->source is a redundant null string pointer check. Detected with
smatch:
drivers/acpi/pci_irq.c:134 do_prt_fixups() warn: this array is probably
non-NULL. 'prt->source'
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Avoid IRQs occupied by ISA IRQs when allocating IRQs for PCI link devices,
otherwise it may cause interrupt storm due to incompatible pin attributes.
This issue was triggered on a KVM virtual machine, which
1) uses IRQ9 for SCI in high level mode.
2) defines an PCI interrupt link device (LNKS) with IRQ9 as the only
possible irq.
3) has an PCI device referring to link device LNKS.
So it causes interrupt storm when enabling the PCI device because PCI IRQ
works in low level mode.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- ACPICA update to upstream revision 20150818 including method
tracing extensions to allow more in-depth AML debugging in the
kernel and a number of assorted fixes and cleanups (Bob Moore,
Lv Zheng, Markus Elfring).
- ACPI sysfs code updates and a documentation update related to
AML method tracing (Lv Zheng).
- ACPI EC driver fix related to serialized evaluations of _Qxx
methods and ACPI tools updates allowing the EC userspace tool
to be built from the kernel source (Lv Zheng).
- ACPI processor driver updates preparing it for future
introduction of CPPC support and ACPI PCC mailbox driver
updates (Ashwin Chaugule).
- ACPI interrupts enumeration fix for a regression related
to the handling of IRQ attribute conflicts between MADT
and the ACPI namespace (Jiang Liu).
- Fixes related to ACPI device PM (Mika Westerberg, Srinidhi Kasagar).
- ACPI device registration code reorganization to separate the
sysfs-related code and bus type operations from the rest (Rafael
J Wysocki).
- Assorted cleanups in the ACPI core (Jarkko Nikula, Mathias Krause,
Andy Shevchenko, Rafael J Wysocki, Nicolas Iooss).
- ACPI cpufreq driver and ia64 cpufreq driver fixes and cleanups
(Pan Xinhui, Rafael J Wysocki).
- cpufreq core cleanups on top of the previous changes allowing it
to preseve its sysfs directories over system suspend/resume (Viresh
Kumar, Rafael J Wysocki, Sebastian Andrzej Siewior).
- cpufreq fixes and cleanups related to governors (Viresh Kumar).
- cpufreq updates (core and the cpufreq-dt driver) related to the
turbo/boost mode support (Viresh Kumar, Bartlomiej Zolnierkiewicz).
- New DT bindings for Operating Performance Points (OPP), support
for them in the OPP framework and in the cpufreq-dt driver plus
related OPP framework fixes and cleanups (Viresh Kumar).
- cpufreq powernv driver updates (Shilpasri G Bhat).
- New cpufreq driver for Mediatek MT8173 (Pi-Cheng Chen).
- Assorted cpufreq driver (speedstep-lib, sfi, integrator) cleanups
and fixes (Abhilash Jindal, Andrzej Hajda, Cristian Ardelean).
- intel_pstate driver updates including Skylake-S support, support
for enabling HW P-states per CPU and an additional vendor bypass
list entry (Kristen Carlson Accardi, Chen Yu, Ethan Zhao).
- cpuidle core fixes related to the handling of coupled idle states
(Xunlei Pang).
- intel_idle driver updates including Skylake Client support and
support for freeze-mode-specific idle states (Len Brown).
- Driver core updates related to power management (Andy Shevchenko,
Rafael J Wysocki).
- Generic power domains framework fixes and cleanups (Jon Hunter,
Geert Uytterhoeven, Rajendra Nayak, Ulf Hansson).
- Device PM QoS framework update to allow the latency tolerance
setting to be exposed to user space via sysfs (Mika Westerberg).
- devfreq support for PPMUv2 in Exynos5433 and a fix for an incorrect
exynos-ppmu DT binding (Chanwoo Choi, Javier Martinez Canillas).
- System sleep support updates (Alan Stern, Len Brown, SungEun Kim).
- rockchip-io AVS support updates (Heiko Stuebner).
- PM core clocks support fixup (Colin Ian King).
- Power capping RAPL driver update including support for Skylake H/S
and Broadwell-H (Radivoje Jovanovic, Seiichi Ikarashi).
- Generic device properties framework fixes related to the handling
of static (driver-provided) property sets (Andy Shevchenko).
- turbostat and cpupower updates (Len Brown, Shilpasri G Bhat,
Shreyas B Prabhu).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=fTgI
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael Wysocki:
"From the number of commits perspective, the biggest items are ACPICA
and cpufreq changes with the latter taking the lead (over 50 commits).
On the cpufreq front, there are many cleanups and minor fixes in the
core and governors, driver updates etc. We also have a new cpufreq
driver for Mediatek MT8173 chips.
ACPICA mostly updates its debug infrastructure and adds a number of
fixes and cleanups for a good measure.
The Operating Performance Points (OPP) framework is updated with new
DT bindings and support for them among other things.
We have a few updates of the generic power domains framework and a
reorganization of the ACPI device enumeration code and bus type
operations.
And a lot of fixes and cleanups all over.
Included is one branch from the MFD tree as it contains some
PM-related driver core and ACPI PM changes a few other commits are
based on.
Specifics:
- ACPICA update to upstream revision 20150818 including method
tracing extensions to allow more in-depth AML debugging in the
kernel and a number of assorted fixes and cleanups (Bob Moore, Lv
Zheng, Markus Elfring).
- ACPI sysfs code updates and a documentation update related to AML
method tracing (Lv Zheng).
- ACPI EC driver fix related to serialized evaluations of _Qxx
methods and ACPI tools updates allowing the EC userspace tool to be
built from the kernel source (Lv Zheng).
- ACPI processor driver updates preparing it for future introduction
of CPPC support and ACPI PCC mailbox driver updates (Ashwin
Chaugule).
- ACPI interrupts enumeration fix for a regression related to the
handling of IRQ attribute conflicts between MADT and the ACPI
namespace (Jiang Liu).
- Fixes related to ACPI device PM (Mika Westerberg, Srinidhi
Kasagar).
- ACPI device registration code reorganization to separate the
sysfs-related code and bus type operations from the rest (Rafael J
Wysocki).
- Assorted cleanups in the ACPI core (Jarkko Nikula, Mathias Krause,
Andy Shevchenko, Rafael J Wysocki, Nicolas Iooss).
- ACPI cpufreq driver and ia64 cpufreq driver fixes and cleanups (Pan
Xinhui, Rafael J Wysocki).
- cpufreq core cleanups on top of the previous changes allowing it to
preseve its sysfs directories over system suspend/resume (Viresh
Kumar, Rafael J Wysocki, Sebastian Andrzej Siewior).
- cpufreq fixes and cleanups related to governors (Viresh Kumar).
- cpufreq updates (core and the cpufreq-dt driver) related to the
turbo/boost mode support (Viresh Kumar, Bartlomiej Zolnierkiewicz).
- New DT bindings for Operating Performance Points (OPP), support for
them in the OPP framework and in the cpufreq-dt driver plus related
OPP framework fixes and cleanups (Viresh Kumar).
- cpufreq powernv driver updates (Shilpasri G Bhat).
- New cpufreq driver for Mediatek MT8173 (Pi-Cheng Chen).
- Assorted cpufreq driver (speedstep-lib, sfi, integrator) cleanups
and fixes (Abhilash Jindal, Andrzej Hajda, Cristian Ardelean).
- intel_pstate driver updates including Skylake-S support, support
for enabling HW P-states per CPU and an additional vendor bypass
list entry (Kristen Carlson Accardi, Chen Yu, Ethan Zhao).
- cpuidle core fixes related to the handling of coupled idle states
(Xunlei Pang).
- intel_idle driver updates including Skylake Client support and
support for freeze-mode-specific idle states (Len Brown).
- Driver core updates related to power management (Andy Shevchenko,
Rafael J Wysocki).
- Generic power domains framework fixes and cleanups (Jon Hunter,
Geert Uytterhoeven, Rajendra Nayak, Ulf Hansson).
- Device PM QoS framework update to allow the latency tolerance
setting to be exposed to user space via sysfs (Mika Westerberg).
- devfreq support for PPMUv2 in Exynos5433 and a fix for an incorrect
exynos-ppmu DT binding (Chanwoo Choi, Javier Martinez Canillas).
- System sleep support updates (Alan Stern, Len Brown, SungEun Kim).
- rockchip-io AVS support updates (Heiko Stuebner).
- PM core clocks support fixup (Colin Ian King).
- Power capping RAPL driver update including support for Skylake H/S
and Broadwell-H (Radivoje Jovanovic, Seiichi Ikarashi).
- Generic device properties framework fixes related to the handling
of static (driver-provided) property sets (Andy Shevchenko).
- turbostat and cpupower updates (Len Brown, Shilpasri G Bhat,
Shreyas B Prabhu)"
* tag 'pm+acpi-4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (180 commits)
cpufreq: speedstep-lib: Use monotonic clock
cpufreq: powernv: Increase the verbosity of OCC console messages
cpufreq: sfi: use kmemdup rather than duplicating its implementation
cpufreq: drop !cpufreq_driver check from cpufreq_parse_governor()
cpufreq: rename cpufreq_real_policy as cpufreq_user_policy
cpufreq: remove redundant 'policy' field from user_policy
cpufreq: remove redundant 'governor' field from user_policy
cpufreq: update user_policy.* on success
cpufreq: use memcpy() to copy policy
cpufreq: remove redundant CPUFREQ_INCOMPATIBLE notifier event
cpufreq: mediatek: Add MT8173 cpufreq driver
dt-bindings: mediatek: Add MT8173 CPU DVFS clock bindings
PM / Domains: Fix typo in description of genpd_dev_pm_detach()
PM / Domains: Remove unusable governor dummies
PM / Domains: Make pm_genpd_init() available to modules
PM / domains: Align column headers and data in pm_genpd_summary output
powercap / RAPL: disable the 2nd power limit properly
tools: cpupower: Fix error when running cpupower monitor
PM / OPP: Drop unlikely before IS_ERR(_OR_NULL)
PM / OPP: Fix static checker warning (broken 64bit big endian systems)
...
Add pci_has_managed_irq(), pci_set_managed_irq(), and
pci_reset_managed_irq() to simplify code. No functional change.
[bhelgaas: changelog]
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
To support IOAPIC hotplug, we need to allocate PCI IRQ resources on demand
and free them when not used anymore.
Implement pcibios_alloc_irq() and pcibios_free_irq() to dynamically
allocate and free PCI IRQs.
Remove mp_should_keep_irq(), which is no longer used.
[bhelgaas: changelog]
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
There is no need to carry potentially outdated Free Software Foundation
mailing address in file headers since the COPYING file includes it.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- ACPICA update to upstream revision 20150515 including basic
support for ACPI 6 features: new ACPI tables introduced by
ACPI 6 (STAO, XENV, WPBT, NFIT, IORT), changes related to the
other tables (DTRM, FADT, LPIT, MADT), new predefined names
(_BTH, _CR3, _DSD, _LPI, _MTL, _PRR, _RDI, _RST, _TFP, _TSN),
fixes and cleanups (Bob Moore, Lv Zheng).
- ACPI device power management core code update to follow ACPI 6
which reflects the ACPI device power management implementation
in Windows (Rafael J Wysocki).
- Rework of the backlight interface selection logic to reduce the
number of kernel command line options and improve the handling
of DMI quirks that may be involved in that and to make the
code generally more straightforward (Hans de Goede).
- Fixes for the ACPI Embedded Controller (EC) driver related to
the handling of EC transactions (Lv Zheng).
- Fix for a regression related to the ACPI resources management
and resulting from a recent change of ACPI initialization code
ordering (Rafael J Wysocki).
- Fix for a system initialization regression related to ACPI
introduced during the 3.14 cycle and caused by running the
code that switches the platform over to the ACPI mode too
early in the initialization sequence (Rafael J Wysocki).
- Support for the ACPI _CCA device configuration object related
to DMA cache coherence (Suravee Suthikulpanit).
- ACPI/APEI fixes and cleanups (Jiri Kosina, Borislav Petkov).
- ACPI battery driver cleanups (Luis Henriques, Mathias Krause).
- ACPI processor driver cleanups (Hanjun Guo).
- Cleanups and documentation update related to the ACPI device
properties interface based on _DSD (Rafael J Wysocki).
- ACPI device power management fixes (Rafael J Wysocki).
- Assorted cleanups related to ACPI (Dominik Brodowski. Fabian
Frederick, Lorenzo Pieralisi, Mathias Krause, Rafael J Wysocki).
- Fix for a long-standing issue causing General Protection Faults
to be generated occasionally on return to user space after resume
from ACPI-based suspend-to-RAM on 32-bit x86 (Ingo Molnar).
- Fix to make the suspend core code return -EBUSY consistently in
all cases when system suspend is aborted due to wakeup detection
(Ruchi Kandoi).
- Support for automated device wakeup IRQ handling allowing drivers
to make their PM support more starightforward (Tony Lindgren).
- New tracepoints for suspend-to-idle tracing and rework of the
prepare/complete callbacks tracing in the PM core (Todd E Brandt,
Rafael J Wysocki).
- Wakeup sources framework enhancements (Jin Qian).
- New macro for noirq system PM callbacks (Grygorii Strashko).
- Assorted cleanups related to system suspend (Rafael J Wysocki).
- cpuidle core cleanups to make the code more efficient (Rafael J
Wysocki).
- powernv/pseries cpuidle driver update (Shilpasri G Bhat).
- cpufreq core fixes related to CPU online/offline that should
reduce the overhead of these operations quite a bit, unless the
CPU in question is physically going away (Viresh Kumar, Saravana
Kannan).
- Serialization of cpufreq governor callbacks to avoid race
conditions in some cases (Viresh Kumar).
- intel_pstate driver fixes and cleanups (Doug Smythies, Prarit
Bhargava, Joe Konno).
- cpufreq driver (arm_big_little, cpufreq-dt, qoriq) updates (Sudeep
Holla, Felipe Balbi, Tang Yuantian).
- Assorted cleanups in cpufreq drivers and core (Shailendra Verma,
Fabian Frederick, Wang Long).
- New Device Tree bindings for representing Operating Performance
Points (Viresh Kumar).
- Updates for the common clock operations support code in the PM
core (Rajendra Nayak, Geert Uytterhoeven).
- PM domains core code update (Geert Uytterhoeven).
- Intel Knights Landing support for the RAPL (Running Average Power
Limit) power capping driver (Dasaratharaman Chandramouli).
- Fixes related to the floor frequency setting on Atom SoCs in the
RAPL power capping driver (Ajay Thomas).
- Runtime PM framework documentation update (Ben Dooks).
- cpupower tool fix (Herton R Krzesinski).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=7jTj
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael Wysocki:
"The rework of backlight interface selection API from Hans de Goede
stands out from the number of commits and the number of affected
places perspective. The cpufreq core fixes from Viresh Kumar are
quite significant too as far as the number of commits goes and because
they should reduce CPU online/offline overhead quite a bit in the
majority of cases.
From the new featues point of view, the ACPICA update (to upstream
revision 20150515) adding support for new ACPI 6 material to ACPICA is
the one that matters the most as some new significant features will be
based on it going forward. Also included is an update of the ACPI
device power management core to follow ACPI 6 (which in turn reflects
the Windows' device PM implementation), a PM core extension to support
wakeup interrupts in a more generic way and support for the ACPI _CCA
device configuration object.
The rest is mostly fixes and cleanups all over and some documentation
updates, including new DT bindings for Operating Performance Points.
There is one fix for a regression introduced in the 4.1 cycle, but it
adds quite a number of lines of code, it wasn't really ready before
Thursday and you were on vacation, so I refrained from pushing it on
the last minute for 4.1.
Specifics:
- ACPICA update to upstream revision 20150515 including basic support
for ACPI 6 features: new ACPI tables introduced by ACPI 6 (STAO,
XENV, WPBT, NFIT, IORT), changes related to the other tables (DTRM,
FADT, LPIT, MADT), new predefined names (_BTH, _CR3, _DSD, _LPI,
_MTL, _PRR, _RDI, _RST, _TFP, _TSN), fixes and cleanups (Bob Moore,
Lv Zheng).
- ACPI device power management core code update to follow ACPI 6
which reflects the ACPI device power management implementation in
Windows (Rafael J Wysocki).
- rework of the backlight interface selection logic to reduce the
number of kernel command line options and improve the handling of
DMI quirks that may be involved in that and to make the code
generally more straightforward (Hans de Goede).
- fixes for the ACPI Embedded Controller (EC) driver related to the
handling of EC transactions (Lv Zheng).
- fix for a regression related to the ACPI resources management and
resulting from a recent change of ACPI initialization code ordering
(Rafael J Wysocki).
- fix for a system initialization regression related to ACPI
introduced during the 3.14 cycle and caused by running the code
that switches the platform over to the ACPI mode too early in the
initialization sequence (Rafael J Wysocki).
- support for the ACPI _CCA device configuration object related to
DMA cache coherence (Suravee Suthikulpanit).
- ACPI/APEI fixes and cleanups (Jiri Kosina, Borislav Petkov).
- ACPI battery driver cleanups (Luis Henriques, Mathias Krause).
- ACPI processor driver cleanups (Hanjun Guo).
- cleanups and documentation update related to the ACPI device
properties interface based on _DSD (Rafael J Wysocki).
- ACPI device power management fixes (Rafael J Wysocki).
- assorted cleanups related to ACPI (Dominik Brodowski, Fabian
Frederick, Lorenzo Pieralisi, Mathias Krause, Rafael J Wysocki).
- fix for a long-standing issue causing General Protection Faults to
be generated occasionally on return to user space after resume from
ACPI-based suspend-to-RAM on 32-bit x86 (Ingo Molnar).
- fix to make the suspend core code return -EBUSY consistently in all
cases when system suspend is aborted due to wakeup detection (Ruchi
Kandoi).
- support for automated device wakeup IRQ handling allowing drivers
to make their PM support more starightforward (Tony Lindgren).
- new tracepoints for suspend-to-idle tracing and rework of the
prepare/complete callbacks tracing in the PM core (Todd E Brandt,
Rafael J Wysocki).
- wakeup sources framework enhancements (Jin Qian).
- new macro for noirq system PM callbacks (Grygorii Strashko).
- assorted cleanups related to system suspend (Rafael J Wysocki).
- cpuidle core cleanups to make the code more efficient (Rafael J
Wysocki).
- powernv/pseries cpuidle driver update (Shilpasri G Bhat).
- cpufreq core fixes related to CPU online/offline that should reduce
the overhead of these operations quite a bit, unless the CPU in
question is physically going away (Viresh Kumar, Saravana Kannan).
- serialization of cpufreq governor callbacks to avoid race
conditions in some cases (Viresh Kumar).
- intel_pstate driver fixes and cleanups (Doug Smythies, Prarit
Bhargava, Joe Konno).
- cpufreq driver (arm_big_little, cpufreq-dt, qoriq) updates (Sudeep
Holla, Felipe Balbi, Tang Yuantian).
- assorted cleanups in cpufreq drivers and core (Shailendra Verma,
Fabian Frederick, Wang Long).
- new Device Tree bindings for representing Operating Performance
Points (Viresh Kumar).
- updates for the common clock operations support code in the PM core
(Rajendra Nayak, Geert Uytterhoeven).
- PM domains core code update (Geert Uytterhoeven).
- Intel Knights Landing support for the RAPL (Running Average Power
Limit) power capping driver (Dasaratharaman Chandramouli).
- fixes related to the floor frequency setting on Atom SoCs in the
RAPL power capping driver (Ajay Thomas).
- runtime PM framework documentation update (Ben Dooks).
- cpupower tool fix (Herton R Krzesinski)"
* tag 'pm+acpi-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (194 commits)
cpuidle: powernv/pseries: Auto-promotion of snooze to deeper idle state
x86: Load __USER_DS into DS/ES after resume
PM / OPP: Add binding for 'opp-suspend'
PM / OPP: Allow multiple OPP tables to be passed via DT
PM / OPP: Add new bindings to address shortcomings of existing bindings
ACPI: Constify ACPI device IDs in documentation
ACPI / enumeration: Document the rules regarding the PRP0001 device ID
ACPI / video: Make acpi_video_unregister_backlight() private
acpi-video-detect: Remove old API
toshiba-acpi: Port to new backlight interface selection API
thinkpad-acpi: Port to new backlight interface selection API
sony-laptop: Port to new backlight interface selection API
samsung-laptop: Port to new backlight interface selection API
msi-wmi: Port to new backlight interface selection API
msi-laptop: Port to new backlight interface selection API
intel-oaktrail: Port to new backlight interface selection API
ideapad-laptop: Port to new backlight interface selection API
fujitsu-laptop: Port to new backlight interface selection API
eeepc-laptop: Port to new backlight interface selection API
dell-wmi: Port to new backlight interface selection API
...
The PCIe specification, rev 3.0, section 2.2.8.1, contains the following
implementation note:
Virtual Wire Mapping for INTx Interrupts From ARI Devices
The implied Device Number for an ARI Device is 0. When ARI-aware
software (including BIOS and operating system) enables ARI Forwarding in
the Downstream Port immediately above an ARI Device in order to access
its Extended Functions, software must comprehend that the Downstream Port
will use Device Number 0 for the virtual wire mappings of INTx interrupts
coming from all Functions of the ARI Device. If non-ARI-aware software
attempts to determine the virtual wire mappings for Extended Functions,
it can come up with incorrect mappings by examining the traditional
Device Number field and finding it to be non-0.
We account for this in pci_swizzle_interrupt_pin(), but it looks like we
miss it here, looking for a _PRT entry with a slot matching the ARI device
slot number. This can cause errors like:
pcieport 0000:80:03.0: can't derive routing for PCI INT B
sfc 0000:82:01.1: PCI INT B: no GSI
pci_dev.irq is then invalid, resulting in errors for drivers that attempt
to enable INTx on the device. Fix by using slot 0 for ARI enabled devices.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Don Dutile <ddutile@redhat.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
list_head "list" in struct acpi_prt_entry was used to connect
_PRT entries for PCI irq, but after commit 181380b702 ("PCI/ACPI:
Don't cache _PRT, and don't associate them with bus numbers"),
the list head for _PRT entries was removed, but left "list" in
struct acpi_prt_entry which is useless and stale, remove it now.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit b4b55cda58 (Refine the way to release PCI IRQ resources)
introduced a regression in the PCI IRQ resource management by causing
the IRQ resource of a device, established when pci_enabled_device()
is called on a fully disabled device, to be released when the driver
is unbound from the device, regardless of the enable_cnt.
This leads to the situation that an ill-behaved driver can now make a
device unusable to subsequent drivers by an imbalance in their use of
pci_enable/disable_device(). That is a serious problem for secondary
drivers like vfio-pci, which are innocent of the transgressions of
the previous driver.
Since the solution of this problem is not immediate and requires
further discussion, revert commit b4b55cda58 and the issue it was
supposed to address (a bug related to xen-pciback) will be taken
care of in a different way going forward.
Reported-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some PCI device drivers assume that pci_dev->irq won't change after
calling pci_disable_device() and pci_enable_device() during suspend and
resume.
Commit c03b3b0738 ("x86, irq, mpparse: Release IOAPIC pin when
PCI device is disabled") frees PCI IRQ resources when pci_disable_device()
is called and reallocate IRQ resources when pci_enable_device() is
called again. This breaks above assumption. So commit 3eec595235
("x86, irq, PCI: Keep IRQ assignment for PCI devices during
suspend/hibernation") and 9eabc99a63 ("x86, irq, PCI: Keep IRQ
assignment for runtime power management") fix the issue by avoiding
freeing/reallocating IRQ resources during PCI device suspend/resume.
They achieve this by checking dev.power.is_prepared and
dev.power.runtime_status. PM maintainer, Rafael, then pointed out that
it's really an ugly fix which leaking PM internal state information to
IRQ subsystem.
Recently David Vrabel <david.vrabel@citrix.com> also reports an
regression in pciback driver caused by commit cffe0a2b5a ("x86, irq:
Keep balance of IOAPIC pin reference count"). Please refer to:
http://lkml.org/lkml/2015/1/14/546
So this patch refine the way to release PCI IRQ resources. Instead of
releasing PCI IRQ resources in pci_disable_device()/
pcibios_disable_device(), we now release it at driver unbinding
notification BUS_NOTIFY_UNBOUND_DRIVER. In other word, we only release
PCI IRQ resources when there's no driver bound to the PCI device, and
it keeps the assumption that pci_dev->irq won't through multiple
invocation of pci_enable_device()/pci_disable_device().
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Xen pciback driver assumes that pci_dev->irq won't change after calling
pci_disable_device(). But commit cffe0a2b5a
("x86, irq: Keep balance of IOAPIC pin reference count") frees irq
resources and resets pci_dev->irq to zero when pci_disable_device() is
called.
So this is a hotfix for 3.19 to avoid resetting pci_dev->irq, and
another proper fix will be prepared for next merging window.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Tested-by: Sander Eikelenboom <linux@eikelenboom.it>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Len Brown <lenb@kernel.org>
Link: http://lkml.kernel.org/r/1421720467-7709-3-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull x86 apic updates from Thomas Gleixner:
"After stopping the full x86/apic branch, I took some time to go
through the first block of patches again, which are mostly cleanups
and preparatory work for the irqdomain conversion and ioapic hotplug
support.
Unfortunaly one of the real problematic commits was right at the
beginning, so I rebased this portion of the pending patches without
the offenders.
It would be great to get this into 3.19. That makes reworking the
problematic parts simpler. The usual tip testing did not unearth any
issues and it is fully bisectible now.
I'm pretty confident that this wont affect the calmness of the xmas
season.
Changes:
- Split the convoluted io_apic.c code into domain specific parts
(vector, ioapic, msi, htirq)
- Introduce proper helper functions to retrieve irq specific data
instead of open coded dereferencing of pointers
- Preparatory work for ioapic hotplug and irqdomain conversion
- Removal of the non functional pci-ioapic driver
- Removal of unused irq entry stubs
- Make native_smp_prepare_cpus() preemtible to avoid GFP_ATOMIC
allocations for everything which is called from there.
- Small cleanups and fixes"
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
iommu/amd: Use helpers to access irq_cfg data structure associated with IRQ
iommu/vt-d: Use helpers to access irq_cfg data structure associated with IRQ
x86: irq_remapping: Use helpers to access irq_cfg data structure associated with IRQ
x86, irq: Use helpers to access irq_cfg data structure associated with IRQ
x86, irq: Make MSI and HT_IRQ indepenent of X86_IO_APIC
x86, irq: Move IRQ initialization routines from io_apic.c into vector.c
x86, irq: Move IOAPIC related declarations from hw_irq.h into io_apic.h
x86, irq: Move HT IRQ related code from io_apic.c into htirq.c
x86, irq: Move PCI MSI related code from io_apic.c into msi.c
x86, irq: Replace printk(KERN_LVL) with pr_lvl() utilities
x86, irq: Make UP version of irq_complete_move() an inline stub
x86, irq: Move local APIC related code from io_apic.c into vector.c
x86, irq: Introduce helpers to access struct irq_cfg
x86, irq: Protect __clear_irq_vector() with vector_lock
x86, irq: Rename local APIC related functions in io_apic.c as apic_xxx()
x86, irq: Refine hw_irq.h to prepare for irqdomain support
x86, irq: Convert irq_2_pin list to generic list
x86, irq: Kill useless parameter 'irq_attr' of IO_APIC_get_PCI_irq_vector()
x86, irq, acpi: Get rid of special handling of GSI for ACPI SCI
x86, irq: Introduce helper to check whether an IOAPIC has been registered
...
To keep balance of IOAPIC pin reference count, we need to protect
pirq_enable_irq(), acpi_pci_irq_enable() and intel_mid_pci_irq_enable()
from reentrance. There are two cases which will cause reentrance.
The first case is caused by suspend/hibernation. If pcibios_disable_irq
is called during suspending/hibernating, we don't release the assigned
IRQ number, otherwise it may break the suspend/hibernation. So late when
pcibios_enable_irq is called during resume, we shouldn't allocate IRQ
number again.
The second case is that function acpi_pci_irq_enable() may be called
twice for PCI devices present at boot time as below:
1) pci_acpi_init()
--> acpi_pci_irq_enable() if pci_routeirq is true
2) pci_enable_device()
--> pcibios_enable_device()
--> acpi_pci_irq_enable()
We can't kill kernel parameter pci_routeirq yet because it's still
needed for debugging purpose.
So flag irq_managed is introduced to track whether IRQ number is
assigned by OS and to protect pirq_enable_irq(), acpi_pci_irq_enable()
and intel_mid_pci_irq_enable() from reentrance.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Len Brown <lenb@kernel.org>
Link: http://lkml.kernel.org/r/1414387308-27148-13-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so quite a few
depend on CONFIG_PM.
Replace CONFIG_PM_RUNTIME with CONFIG_PM in the ACPI core code.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Now IOAPIC driver dynamically allocates IRQ numbers for IOAPIC pins.
We need to keep IRQ assignment for PCI devices during runtime power
management, otherwise it may cause failure of device wakeups.
Commit 3eec595235 "x86, irq, PCI: Keep IRQ assignment for PCI
devices during suspend/hibernation" has fixed the issue for suspend/
hibernation, we also need the same fix for runtime device sleep too.
Fix: https://bugzilla.kernel.org/show_bug.cgi?id=83271
Reported-and-Tested-by: EmanueL Czirai <amanual@openmailbox.org>
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: EmanueL Czirai <amanual@openmailbox.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Grant Likely <grant.likely@linaro.org>
Link: http://lkml.kernel.org/r/1409304383-18806-1-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Now IOAPIC driver dynamically allocates IRQ numbers for IOAPIC pins.
We need to keep IRQ assignment for PCI devices during suspend/hibernation,
otherwise it may cause failure of suspend/hibernation due to:
1) Device driver calls pci_enable_device() to allocate an IRQ number
and register interrupt handler on the returned IRQ.
2) Device driver's suspend callback calls pci_disable_device() and
release assigned IRQ in turn.
3) Device driver's resume callback calls pci_enable_device() to
allocate IRQ number again. A different IRQ number may be assigned
by IOAPIC driver this time.
4) Now the hardware delivers interrupt to the new IRQ but interrupt
handler is still registered against the old IRQ, so it breaks
suspend/hibernation.
To fix this issue, we keep IRQ assignment during suspend/hibernation.
Flag pci_dev.dev.power.is_prepared is used to detect that
pci_disable_device() is called during suspend/hibernation.
Reported-and-Tested-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Len Brown <lenb@kernel.org>
Link: http://lkml.kernel.org/r/1407478071-29399-1-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Release IOAPIC pin associated with PCI device when the PCI device
is disabled.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Len Brown <len.brown@intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Link: http://lkml.kernel.org/r/1402380987-32577-1-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This commit moves ISA-specific code to separate function and makes that
function depend on CONFIG_{E}ISA so that we do not have to maintain
acpi_isa_irq_to_gsi() function for architectures which do not support ISA.
Signed-off-by: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
acpi_pci_link_allocate_irq() can return negative gsi even if
entry != NULL. For that case we have a memory leak, so free
entry before returning from acpi_pci_irq_enable() for gsi < 0.
Signed-off-by: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Cc: All applicable <stable@vger.kernel.org>
[rjw: Subject and changelog]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Replace direct inclusions of <acpi/acpi.h>, <acpi/acpi_bus.h> and
<acpi/acpi_drivers.h>, which are incorrect, with <linux/acpi.h>
inclusions and remove some inclusions of those files that aren't
necessary.
First of all, <acpi/acpi.h>, <acpi/acpi_bus.h> and <acpi/acpi_drivers.h>
should not be included directly from any files that are built for
CONFIG_ACPI unset, because that generally leads to build warnings about
undefined symbols in !CONFIG_ACPI builds. For CONFIG_ACPI set,
<linux/acpi.h> includes those files and for CONFIG_ACPI unset it
provides stub ACPI symbols to be used in that case.
Second, there are ordering dependencies between those files that always
have to be met. Namely, it is required that <acpi/acpi_bus.h> be included
prior to <acpi/acpi_drivers.h> so that the acpi_pci_root declarations the
latter depends on are always there. And <acpi/acpi.h> which provides
basic ACPICA type declarations should always be included prior to any other
ACPI headers in CONFIG_ACPI builds. That also is taken care of including
<linux/acpi.h> as appropriate.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> (drivers/pci stuff)
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> (Xen stuff)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Previously, we cached _PRT (PCI routing table, ACPI 5.0 sec 6.2.12)
contents and associated each _PRT entry with a PCI bus number. The bus
number association means dependencies on PCI device enumeration and bus
number assignment, as well as on the PCI/ACPI binding process.
After 4f535093cf ("PCI: Put pci_dev in device tree as early as possible"),
these dependencies caused the IRQ issues reported by Peter:
pci 0000:00:1e.0: PCI bridge to [bus 09] (subtractive decode)
pci 0000:00:1e.0: can't derive routing for PCI INT A
snd_ctxfi 0000:09:02.0: PCI INT A: no GSI - using ISA IRQ 5
irq 18: nobody cared (try booting with the "irqpoll" option)
This patch removes _PRT caching. Instead, we evaluate _PRT as needed
in the pci_enable_device() path. This also removes the dependency on
PCI bus numbers: we can simply look at the _PRT associated with each
bridge as we walk upstream toward the root.
[bhelgaas: changelog]
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=53561
Reported-and-tested-by: Peter Hurley <peter@hurleysoftware.com>
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Host bridge hotplug:
- Untangle _PRT from struct pci_bus (Bjorn Helgaas)
- Request _OSC control before scanning root bus (Taku Izumi)
- Assign resources when adding host bridge (Yinghai Lu)
- Remove root bus when removing host bridge (Yinghai Lu)
- Remove _PRT during hot remove (Yinghai Lu)
SRIOV
- Add sysfs knobs to control numVFs (Don Dutile)
Power management
- Notify devices when power resource turned on (Huang Ying)
Bug fixes
- Work around broken _SEG on HP xw9300 (Bjorn Helgaas)
- Keep runtime PM enabled for unbound PCI devices (Huang Ying)
- Fix Optimus dual-GPU runtime D3 suspend issue (Dave Airlie)
- Fix xen frontend shutdown issue (David Vrabel)
- Work around PLX PCI 9050 BAR alignment erratum (Ian Abbott)
Miscellaneous
- Add GPL license for drivers/pci/ioapic (Andrew Cooks)
- Add standard PCI-X, PCIe ASPM register #defines (Bjorn Helgaas)
- NumaChip remote PCI support (Daniel Blueman)
- Fix PCIe Link Capabilities Supported Link Speed definition (Jingoo Han)
- Convert dev_printk() to dev_info(), etc (Joe Perches)
- Add support for non PCI BAR ROM data (Matthew Garrett)
- Add x86 support for host bridge translation offset (Mike Yoknis)
- Report success only when every driver supports AER (Vijay Pandarathil)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=OE3Q
-----END PGP SIGNATURE-----
Merge tag 'for-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI update from Bjorn Helgaas:
"Host bridge hotplug:
- Untangle _PRT from struct pci_bus (Bjorn Helgaas)
- Request _OSC control before scanning root bus (Taku Izumi)
- Assign resources when adding host bridge (Yinghai Lu)
- Remove root bus when removing host bridge (Yinghai Lu)
- Remove _PRT during hot remove (Yinghai Lu)
SRIOV
- Add sysfs knobs to control numVFs (Don Dutile)
Power management
- Notify devices when power resource turned on (Huang Ying)
Bug fixes
- Work around broken _SEG on HP xw9300 (Bjorn Helgaas)
- Keep runtime PM enabled for unbound PCI devices (Huang Ying)
- Fix Optimus dual-GPU runtime D3 suspend issue (Dave Airlie)
- Fix xen frontend shutdown issue (David Vrabel)
- Work around PLX PCI 9050 BAR alignment erratum (Ian Abbott)
Miscellaneous
- Add GPL license for drivers/pci/ioapic (Andrew Cooks)
- Add standard PCI-X, PCIe ASPM register #defines (Bjorn Helgaas)
- NumaChip remote PCI support (Daniel Blueman)
- Fix PCIe Link Capabilities Supported Link Speed definition (Jingoo
Han)
- Convert dev_printk() to dev_info(), etc (Joe Perches)
- Add support for non PCI BAR ROM data (Matthew Garrett)
- Add x86 support for host bridge translation offset (Mike Yoknis)
- Report success only when every driver supports AER (Vijay
Pandarathil)"
Fix up trivial conflicts.
* tag 'for-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (48 commits)
PCI: Use phys_addr_t for physical ROM address
x86/PCI: Add NumaChip remote PCI support
ath9k: Use standard #defines for PCIe Capability ASPM fields
iwlwifi: Use standard #defines for PCIe Capability ASPM fields
iwlwifi: collapse wrapper for pcie_capability_read_word()
iwlegacy: Use standard #defines for PCIe Capability ASPM fields
iwlegacy: collapse wrapper for pcie_capability_read_word()
cxgb3: Use standard #defines for PCIe Capability ASPM fields
PCI: Add standard PCIe Capability Link ASPM field names
PCI/portdrv: Use PCI Express Capability accessors
PCI: Use standard PCIe Capability Link register field names
x86: Use PCI setup data
PCI: Add support for non-BAR ROMs
PCI: Add pcibios_add_device
EFI: Stash ROMs if they're not in the PCI BAR
PCI: Add and use standard PCI-X Capability register names
PCI/PM: Keep runtime PM enabled for unbound PCI devices
xen-pcifront: Handle backend CLOSED without CLOSING
PCI: SRIOV control and status via sysfs (documentation)
PCI/AER: Report success only when every device has AER-aware driver
...
* acpi-general: (38 commits)
ACPI / thermal: _TMP and _CRT/_HOT/_PSV/_ACx dependency fix
ACPI: drop unnecessary local variable from acpi_system_write_wakeup_device()
ACPI: Fix logging when no pci_irq is allocated
ACPI: Update Dock hotplug error messages
ACPI: Update Container hotplug error messages
ACPI: Update Memory hotplug error messages
ACPI: Update CPU hotplug error messages
ACPI: Add acpi_handle_<level>() interfaces
ACPI: remove use of __devexit
ACPI / PM: Add Sony Vaio VPCEB1S1E to nonvs blacklist.
ACPI / battery: Correct battery capacity values on Thinkpads
Revert "ACPI / x86: Add quirk for "CheckPoint P-20-00" to not use bridge _CRS_ info"
ACPI: create _SUN sysfs file
ACPI / memhotplug: bind the memory device when the driver is being loaded
ACPI / memhotplug: don't allow to eject the memory device if it is being used
ACPI / memhotplug: free memory device if acpi_memory_enable_device() failed
ACPI / memhotplug: fix memory leak when memory device is unbound from acpi_memhotplug
ACPI / memhotplug: deal with eject request in hotplug queue
ACPI / memory-hotplug: add memory offline code to acpi_memory_device_remove()
ACPI / memory-hotplug: call acpi_bus_trim() to remove memory device
...
Conflicts:
include/linux/acpi.h (two additions at the end of the same file)
Work around a defect in the printk subsystem introduced by a
logging change.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
These functions might be called from modules as well so make sure
they are exported.
In addition, implement empty version of acpi_unregister_gsi() and
remove the one from pci_irq.c.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This effectively reverts 859a3f86ca ("ACPI: simplify
acpi_pci_irq_add_prt() API") and d9efae3688 ("ACPI: simplify
acpi_pci_irq_del_prt() API").
The reason is to disentangle these routines from the struct pci_bus.
We want to be able to add the _PRT before the struct pci_bus
exists, and delete the _PRT after we've removed the pci_bus.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
When the runtime PM is activated on PCI, if a device switches state
frequently (e.g. an EHCI controller with autosuspending USB devices
connected) the PCI configuration traces might be very verbose in the
kernel log. Let's guard those traces with DEBUG condition.
Acked-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The following was observed by Steve Rostedt on 3.0.0-rc5
Backtrace:
irq 16: nobody cared (try booting with the "irqpoll" option)
Pid: 65, comm: irq/16-uhci_hcd Not tainted 3.0.0-rc5-test+ #94
Call Trace:
[<ffffffff810aa643>] __report_bad_irq+0x37/0xc1
[<ffffffff810aaa2d>] note_interrupt+0x14e/0x1c9
[<ffffffff810a9a05>] ? irq_thread_fn+0x3c/0x3c
[<ffffffff810a990e>] irq_thread+0xf6/0x1b1
[<ffffffff810a9818>] ? irq_finalize_oneshot+0xb3/0xb3
[<ffffffff8106b4d6>] kthread+0x9f/0xa7
[<ffffffff814f1f04>] kernel_thread_helper+0x4/0x10
[<ffffffff8103ca09>] ? finish_task_switch+0x7b/0xc0
[<ffffffff814eac78>] ? retint_restore_args+0x13/0x13
[<ffffffff8106b437>] ? __init_kthread_worker+0x5a/0x5a
[<ffffffff814f1f00>] ? gs_change+0x13/0x13
handlers:
[<ffffffff810a912d>] irq_default_primary_handler threaded [<ffffffff8135eaa6>] usb_hcd_irq
[<ffffffff810a912d>] irq_default_primary_handler threaded [<ffffffff8135eaa6>] usb_hcd_irq
Disabling IRQ #16
The problem being that a device triggers boot interrupts (due to threaded
interrupt handling and masking of the IO-APIC), which are forwarded
to the PIRQ line of the device. These interrupts are not handled on the PIRQ
line because the interrupt handler is not present there.
This should have already been fixed by CONFIG_X86_REROUTE_FOR_BROKEN_BOOT_IRQS.
However some parts of the quirk got lost in the ACPI merge. This is a resent of
the patch proposed in 2009.
See http://lkml.org/lkml/2009/9/7/192
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Strictly speaking on x86 (where acpi is used) dev->irq must be
a dual i8259 irq input aka an isa irq. Therefore we should translate
that isa irq into a gsi before passing it to a function that
takes a gsi.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
LKML-Reference: <1269936436-7039-3-git-send-email-ebiederm@xmission.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Linux/ACPI core files using internal.h all PREFIX "ACPI: ",
however, not all ACPI drivers use/want it -- and they
should not have to #undef PREFIX to define their own.
Add GPL commment to internal.h while we are there.
This does not change any actual console output,
asside from a whitespace fix.
Signed-off-by: Len Brown <len.brown@intel.com>
There is no need to pass a segment/bus tuple to this API, as the callsite
always has a struct pci_bus. We can derive segment/bus from the
struct pci_bus, so let's take this opportunit to simplify the API and
make life easier for the callers.
Signed-off-by: Alex Chiang <achiang@hp.com>
Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
A PCI domain cannot change as you descend down subordinate buses, which
makes the 'segment' argument to acpi_pci_irq_add_prt() useless.
Change the interface to take a struct pci_bus *, from whence we can derive
the bus number and segment. Reducing the number of arguments makes life
simpler for callers.
Signed-off-by: Alex Chiang <achiang@hp.com>
Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
We want to use dev_to_node() later on, to be aware of the 'home node'
of the GSI in question.
[ Impact: cleanup, prepare the IRQ code to be more NUMA aware ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Len Brown <lenb@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Len Brown <lenb@kernel.org>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-acpi@vger.kernel.org
Cc: linux-ia64@vger.kernel.org
LKML-Reference: <49F65560.20904@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Use the generic pci_swizzle_interrupt_pin() instead of ACPI-specific code.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch makes function declarations consistent throughout
the file and removes some unnecessary initializations.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi_pci_allocate_irq() and acpi_pci_free_irq() are trivial and
only used once, so just open-code them.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
We don't need a struct containing a count and a list_head; a simple
list_head is sufficient. The list iterators handle empty lists
fine.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This folds acpi_pci_irq_derive() into acpi_pci_irq_lookup() so it
can be easily used by both acpi_pci_irq_enable() and acpi_pci_irq_disable().
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Lorenzo Pieralisi