Calling ceph_buffer_put() in __ceph_build_xattrs_blob() may result in
freeing the i_xattrs.blob buffer while holding the i_ceph_lock. This can
be fixed by having this function returning the old blob buffer and have
the callers of this function freeing it when the lock is released.
The following backtrace was triggered by fstests generic/117.
BUG: sleeping function called from invalid context at mm/vmalloc.c:2283
in_atomic(): 1, irqs_disabled(): 0, pid: 649, name: fsstress
4 locks held by fsstress/649:
#0: 00000000a7478e7e (&type->s_umount_key#19){++++}, at: iterate_supers+0x77/0xf0
#1: 00000000f8de1423 (&(&ci->i_ceph_lock)->rlock){+.+.}, at: ceph_check_caps+0x7b/0xc60
#2: 00000000562f2b27 (&s->s_mutex){+.+.}, at: ceph_check_caps+0x3bd/0xc60
#3: 00000000f83ce16a (&mdsc->snap_rwsem){++++}, at: ceph_check_caps+0x3ed/0xc60
CPU: 1 PID: 649 Comm: fsstress Not tainted 5.2.0+ #439
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.1-0-ga5cab58-prebuilt.qemu.org 04/01/2014
Call Trace:
dump_stack+0x67/0x90
___might_sleep.cold+0x9f/0xb1
vfree+0x4b/0x60
ceph_buffer_release+0x1b/0x60
__ceph_build_xattrs_blob+0x12b/0x170
__send_cap+0x302/0x540
? __lock_acquire+0x23c/0x1e40
? __mark_caps_flushing+0x15c/0x280
? _raw_spin_unlock+0x24/0x30
ceph_check_caps+0x5f0/0xc60
ceph_flush_dirty_caps+0x7c/0x150
? __ia32_sys_fdatasync+0x20/0x20
ceph_sync_fs+0x5a/0x130
iterate_supers+0x8f/0xf0
ksys_sync+0x4f/0xb0
__ia32_sys_sync+0xa/0x10
do_syscall_64+0x50/0x1c0
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x7fc6409ab617
Signed-off-by: Luis Henriques <lhenriques@suse.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Calling ceph_buffer_put() in __ceph_setxattr() may end up freeing the
i_xattrs.prealloc_blob buffer while holding the i_ceph_lock. This can be
fixed by postponing the call until later, when the lock is released.
The following backtrace was triggered by fstests generic/117.
BUG: sleeping function called from invalid context at mm/vmalloc.c:2283
in_atomic(): 1, irqs_disabled(): 0, pid: 650, name: fsstress
3 locks held by fsstress/650:
#0: 00000000870a0fe8 (sb_writers#8){.+.+}, at: mnt_want_write+0x20/0x50
#1: 00000000ba0c4c74 (&type->i_mutex_dir_key#6){++++}, at: vfs_setxattr+0x55/0xa0
#2: 000000008dfbb3f2 (&(&ci->i_ceph_lock)->rlock){+.+.}, at: __ceph_setxattr+0x297/0x810
CPU: 1 PID: 650 Comm: fsstress Not tainted 5.2.0+ #437
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.1-0-ga5cab58-prebuilt.qemu.org 04/01/2014
Call Trace:
dump_stack+0x67/0x90
___might_sleep.cold+0x9f/0xb1
vfree+0x4b/0x60
ceph_buffer_release+0x1b/0x60
__ceph_setxattr+0x2b4/0x810
__vfs_setxattr+0x66/0x80
__vfs_setxattr_noperm+0x59/0xf0
vfs_setxattr+0x81/0xa0
setxattr+0x115/0x230
? filename_lookup+0xc9/0x140
? rcu_read_lock_sched_held+0x74/0x80
? rcu_sync_lockdep_assert+0x2e/0x60
? __sb_start_write+0x142/0x1a0
? mnt_want_write+0x20/0x50
path_setxattr+0xba/0xd0
__x64_sys_lsetxattr+0x24/0x30
do_syscall_64+0x50/0x1c0
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x7ff23514359a
Signed-off-by: Luis Henriques <lhenriques@suse.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
The convention with xattrs is to not store the termination with string
data, given that it returns the length. This is how setfattr/getfattr
operate.
Most of ceph's virtual xattr routines use snprintf to plop the string
directly into the destination buffer, but snprintf always NULL
terminates the string. This means that if we send the kernel a buffer
that is the exact length needed to hold the string, it'll end up
truncated.
Add a ceph_fmt_xattr helper function to format the string into an
on-stack buffer that should always be large enough to hold the whole
thing and then memcpy the result into the destination buffer. If it does
turn out that the formatted string won't fit in the on-stack buffer,
then return -E2BIG and do a WARN_ONCE().
Change over most of the virtual xattr routines to use the new helper. A
couple of the xattrs are sourced from strings however, and it's
difficult to know how long they'll be. Just have those memcpy the result
in place after verifying the length.
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: "Yan, Zheng" <zyan@redhat.com>
Acked-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
The getxattr manpage states that we should return ERANGE if the
destination buffer size is too small to hold the value.
ceph_vxattrcb_layout does this internally, but we should be doing
this for all vxattrs.
Fix the only caller of getxattr_cb to check the returned size
against the buffer length and return -ERANGE if it doesn't fit.
Drop the same check in ceph_vxattrcb_layout and just rely on the
caller to handle it.
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: "Yan, Zheng" <zyan@redhat.com>
Acked-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
The getxattr_cb functions return size_t, which is unsigned and then
cast that value to int and then ssize_t before returning it. While all
of this works, it relies on implicit casting rules for signed/unsigned
conversions.
Change getxattr_cb to return ssize_t to better conform with what the
caller actually wants. Also, remove some suspicious casts.
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: "Yan, Zheng" <zyan@redhat.com>
Acked-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
When creating new file/directory, use security_dentry_init_security() to
prepare selinux context for the new inode, then send openc/mkdir request
to MDS, together with selinux xattr.
security_dentry_init_security() only supports single security module and
only selinux has dentry_init_security hook. So only selinux is supported
for now. We can add support for other security modules once kernel has a
generic version of dentry_init_security()
Signed-off-by: "Yan, Zheng" <zyan@redhat.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Also rename ceph_release_acls_info() to ceph_release_acl_sec_ctx().
And move their definitions to different files. This is preparation
for security label support.
Signed-off-by: "Yan, Zheng" <zyan@redhat.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
The vxattr value incorrectly places a "09" prefix to the nanoseconds
field, instead of providing it as a zero-pad width specifier after '%'.
Fixes: 3489b42a72 ("ceph: fix three bugs, two in ceph_vxattrcb_file_layout()")
Link: https://tracker.ceph.com/issues/39943
Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
ceph_listxattr() now calculates the length of vxattrs dynamically, so
these helpers, which incorrectly ignore vxattr.exists_cb(), can be
removed.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: "Yan, Zheng" <zyan@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
ceph_listxattr() incorrectly returns a length based on the static
ceph_vxattrs_name_size() value, which only takes into account whether
vxattrs are hidden, ignoring vxattr.exists_cb().
When filling the xattr buffer ceph_listxattr() checks VXATTR_FLAG_HIDDEN
and vxattr.exists_cb(). If both are false, we return an incorrect
(oversize) length.
Fix this behaviour by always calculating the vxattrs length at runtime,
taking both vxattr.hidden and vxattr.exists_cb() into account.
This bug is only exposed with the new "ceph.snap.btime" vxattr, as all
other vxattrs with a non-null exists_cb also carry VXATTR_FLAG_HIDDEN.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: "Yan, Zheng" <zyan@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
.name_size should use the same string as .name.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: "Yan, Zheng" <zyan@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
struct ceph_pagelist cannot be embedded into anything else because it
has its own refcount. Merge allocation and initialization together.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Since the vfs structures are all using timespec64, we can now
change the internal representation, using ceph_encode_timespec64 and
ceph_decode_timespec64.
In case of ceph_aux_inode however, we need to avoid doing a memcmp()
on uninitialized padding data, so the members of the i_mtime field get
copied individually into 64-bit integers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: "Yan, Zheng" <zyan@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
rstat is not tracked by capability. client can't know if rstat from
non-auth mds is uptodate or not.
Link: http://tracker.ceph.com/issues/23538
Signed-off-by: "Yan, Zheng" <zyan@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
This patch adds the infrastructure required to support cephfs quotas as it
is currently implemented in the ceph fuse client. Cephfs quotas can be
set on any directory, and can restrict the number of bytes or the number
of files stored beneath that point in the directory hierarchy.
Quotas are set using the extended attributes 'ceph.quota.max_files' and
'ceph.quota.max_bytes', and can be removed by setting these attributes to
'0'.
Link: http://tracker.ceph.com/issues/22372
Signed-off-by: Luis Henriques <lhenriques@suse.com>
Reviewed-by: "Yan, Zheng" <zyan@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The script “checkpatch.pl” pointed information out like the following.
Comparison to NULL could be written ...
Thus fix the affected source code places.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Yan, Zheng <zyan@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Previously we were returning values for quota, layout
xattrs without any kind of update -- the user just got
whatever happened to be in our cache.
Clearly this extra round trip has a cost, but reads of
these xattrs are fairly rare, happening on admin
intervention rather than in normal operation.
Link: http://tracker.ceph.com/issues/17939
Signed-off-by: "Yan, Zheng" <zyan@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Fixes the following sparse warning:
fs/ceph/xattr.c:19:28: warning:
symbol 'ceph_other_xattr_handler' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
current_fs_time() uses struct super_block* as an argument.
As per Linus's suggestion, this is changed to take struct
inode* as a parameter instead. This is because the function
is primarily meant for vfs inode timestamps.
Also the function was renamed as per Arnd's suggestion.
Change all calls to current_fs_time() to use the new
current_time() function instead. current_fs_time() will be
deleted.
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This patch adds codes that decode pool namespace information in
cap message and request reply. Pool namespace is saved in i_layout,
it will be passed to libceph when doing read/write.
Signed-off-by: Yan, Zheng <zyan@redhat.com>
Define new ceph_file_layout structure and rename old ceph_file_layout
to ceph_file_layout_legacy. This is preparation for adding namespace
to ceph_file_layout structure.
Signed-off-by: Yan, Zheng <zyan@redhat.com>
Pull vfs fixes from Al Viro:
"Followups to the parallel lookup work:
- update docs
- restore killability of the places that used to take ->i_mutex
killably now that we have down_write_killable() merged
- Additionally, it turns out that I missed a prerequisite for
security_d_instantiate() stuff - ->getxattr() wasn't the only thing
that could be called before dentry is attached to inode; with smack
we needed the same treatment applied to ->setxattr() as well"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
switch ->setxattr() to passing dentry and inode separately
switch xattr_handler->set() to passing dentry and inode separately
restore killability of old mutex_lock_killable(&inode->i_mutex) users
add down_write_killable_nested()
update D/f/directory-locking
Pull Ceph updates from Sage Weil:
"This changeset has a few main parts:
- Ilya has finished a huge refactoring effort to sync up the
client-side logic in libceph with the user-space client code, which
has evolved significantly over the last couple years, with lots of
additional behaviors (e.g., how requests are handled when cluster
is full and transitions from full to non-full).
This structure of the code is more closely aligned with userspace
now such that it will be much easier to maintain going forward when
behavior changes take place. There are some locking improvements
bundled in as well.
- Zheng adds multi-filesystem support (multiple namespaces within the
same Ceph cluster)
- Zheng has changed the readdir offsets and directory enumeration so
that dentry offsets are hash-based and therefore stable across
directory fragmentation events on the MDS.
- Zheng has a smorgasbord of bug fixes across fs/ceph"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: (71 commits)
ceph: fix wake_up_session_cb()
ceph: don't use truncate_pagecache() to invalidate read cache
ceph: SetPageError() for writeback pages if writepages fails
ceph: handle interrupted ceph_writepage()
ceph: make ceph_update_writeable_page() uninterruptible
libceph: make ceph_osdc_wait_request() uninterruptible
ceph: handle -EAGAIN returned by ceph_update_writeable_page()
ceph: make fault/page_mkwrite return VM_FAULT_OOM for -ENOMEM
ceph: block non-fatal signals for fault/page_mkwrite
ceph: make logical calculation functions return bool
ceph: tolerate bad i_size for symlink inode
ceph: improve fragtree change detection
ceph: keep leaf frag when updating fragtree
ceph: fix dir_auth check in ceph_fill_dirfrag()
ceph: don't assume frag tree splits in mds reply are sorted
ceph: fix inode reference leak
ceph: using hash value to compose dentry offset
ceph: don't forbid marking directory complete after forward seek
ceph: record 'offset' for each entry of readdir result
ceph: define 'end/complete' in readdir reply as bit flags
...
Setxattr with NULL value and XATTR_REPLACE flag should be equivalent
to removexattr. But current MDS does not support deleting vxattrs through
MDS_OP_SETXATTR request. The workaround is sending MDS_OP_RMXATTR request
if setxattr actually removs xattr.
Signed-off-by: Yan, Zheng <zyan@redhat.com>
This is a major sync up, up to ~Jewel. The highlights are:
- per-session request trees (vs a global per-client tree)
- per-session locking (vs a global per-client rwlock)
- homeless OSD session
- no ad-hoc global per-client lists
- support for pool quotas
- foundation for watch/notify v2 support
- foundation for map check (pool deletion detection) support
The switchover is incomplete: lingering requests can be setup and
teared down but aren't ever reestablished. This functionality is
restored with the introduction of the new lingering infrastructure
(ceph_osd_linger_request, linger_work, etc) in a later commit.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
when removing a xattr, generic_removexattr() calls __ceph_setxattr()
with NULL value and XATTR_REPLACE flag. __ceph_removexattr() is not
used any more.
Signed-off-by: "Yan, Zheng" <zyan@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Add a catch-all xattr handler at the end of ceph_xattr_handlers. Check
for valid attribute names there, and remove those checks from
__ceph_{get,set,remove}xattr instead. No "system.*" xattrs need to be
handled by the catch-all handler anymore.
The set xattr handler is called with a NULL value to indicate that the
attribute should be removed; __ceph_setxattr already handles that case
correctly (ceph_set_acl could already calling __ceph_setxattr with a NULL
value).
Move the check for snapshots from ceph_{set,remove}xattr into
__ceph_{set,remove}xattr. With that, ceph_{get,set,remove}xattr can be
replaced with the generic iops.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: "Yan, Zheng" <zyan@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Create a variant of ceph_setattr that takes an inode instead of a
dentry. Change __ceph_setxattr (and also __ceph_removexattr) to take an
inode instead of a dentry. Use those in ceph_set_acl so that we no
longer need a dentry there.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: "Yan, Zheng" <zyan@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
When security is enabled, security module can call filesystem's
getxattr/setxattr callbacks during d_instantiate(). For cephfs,
d_instantiate() is usually called by MDS' dispatch thread, while
handling MDS reply. If the MDS reply does not include xattrs and
corresponding caps, getxattr/setxattr need to send a new request
to MDS and waits for the reply. This makes MDS' dispatch sleep,
nobody handles later MDS replies.
The fix is make sure lookup/atomic_open reply include xattrs and
corresponding caps. So getxattr can be handled by cached xattrs.
This requires some modification to both MDS and request message.
(Client tells MDS what caps it wants; MDS encodes proper caps in
the reply)
Smack security module may call setxattr during d_instantiate().
Unlike getxattr, we can't force MDS to issue CEPH_CAP_XATTR_EXCL
to us. So just make setxattr return error when called by MDS'
dispatch thread.
Signed-off-by: Yan, Zheng <zyan@redhat.com>
CURRENT_TIME macro is not appropriate for filesystems as it
doesn't use the right granularity for filesystem timestamps.
Use current_fs_time() instead.
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com>
Signed-off-by: Yan, Zheng <zyan@redhat.com>
When ceph inode's i_head_snapc is NULL, __ceph_mark_dirty_caps()
accesses snap realm's cached_context. So we need take read lock
of snap_rwsem.
Signed-off-by: Yan, Zheng <zyan@redhat.com>
Pull fourth vfs update from Al Viro:
"d_inode() annotations from David Howells (sat in for-next since before
the beginning of merge window) + four assorted fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
RCU pathwalk breakage when running into a symlink overmounting something
fix I_DIO_WAKEUP definition
direct-io: only inc/dec inode->i_dio_count for file systems
fs/9p: fix readdir()
VFS: assorted d_backing_inode() annotations
VFS: fs/inode.c helpers: d_inode() annotations
VFS: fs/cachefiles: d_backing_inode() annotations
VFS: fs library helpers: d_inode() annotations
VFS: assorted weird filesystems: d_inode() annotations
VFS: normal filesystems (and lustre): d_inode() annotations
VFS: security/: d_inode() annotations
VFS: security/: d_backing_inode() annotations
VFS: net/: d_inode() annotations
VFS: net/unix: d_backing_inode() annotations
VFS: kernel/: d_inode() annotations
VFS: audit: d_backing_inode() annotations
VFS: Fix up some ->d_inode accesses in the chelsio driver
VFS: Cachefiles should perform fs modifications on the top layer only
VFS: AF_UNIX sockets should call mknod on the top layer only
Currently, there is no check for the kstrdup() for r_path2,
r_path1 and snapdir_name as various locations as there is a
possibility of failure during memory pressure. Therefore,
returning ENOMEM where the checks have been missed.
Signed-off-by: Sanidhya Kashyap <sanidhya.gatech@gmail.com>
Signed-off-by: Yan, Zheng <zyan@redhat.com>
that's the bulk of filesystem drivers dealing with inodes of their own
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
make sure 'value' is not null. otherwise __ceph_setxattr will remove
the extended attribute.
Signed-off-by: Yan, Zheng <zyan@redhat.com>
Reviewed-by: Sage Weil <sage@redhat.com>
Current code uses page array to present MDS request data. Pages in the
array are allocated/freed by caller of ceph_mdsc_do_request(). If request
is interrupted, the pages can be freed while they are still being used by
the request message.
The fix is use pagelist to present MDS request data. Pagelist is
reference counted.
Signed-off-by: Yan, Zheng <zyan@redhat.com>
Reviewed-by: Sage Weil <sage@redhat.com>
Following sequence of events can happen.
- Client releases an inode, queues cap release message.
- A 'lookup' reply brings the same inode back, but the reply
doesn't contain xattrs because MDS didn't receive the cap release
message and thought client already has up-to-data xattrs.
The fix is force sending a getattr request to MDS if xattrs_version
is 0. The getattr mask is set to CEPH_STAT_CAP_XATTR, so MDS knows client
does not have xattr.
Signed-off-by: Yan, Zheng <zyan@redhat.com>
Luis Henriques