The watchdog interrupt (only used when activating software watchdog)
shouldn't be suspended when entering suspend mode, because it is shared
with a timer device (which request the line with IRQF_NO_SUSPEND) and once
the watchdog "Mode Register" has been written, it cannot be changed (which
means we cannot disable the watchdog interrupt when entering suspend).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
BCM5301X (ARCH_BCM_5301X) is a new Broadcom architecture using the same
SoC bus driver (bcma) as BCM47XX but based on ARM instead of MIPS.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add DT support to the jz4740 driver. Simple of_match_ptr. No other
modification for probe needed
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The dw_wdt_set_top() function takes in a value in seconds. In
dw_wdt_open() we were calling it with a value that's supposed to
represent the maximum value programmed into the "top" register with a
comment saying that we were trying to set the watchdog to its maximum
value. Instead we ended up setting the watchdog to ~15 seconds.
Let's fix this. However, setting things to the "max" gives me an 86
second watchdog in the system I'm looking at. 86 seconds feels a
little too long. We'll explicitly choose 30 seconds as a more
reasonable value.
NOTE: Ideally this driver should be transitioned to be a real watchdog
driver. Then we could use "watchdog_init_timeout" and let the timeout
be specified in a number of ways (device tree, module parameter, etc).
This patch should be considered a bit of a stopgap solution.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
On some dw_wdt implementations the "top" register may be initted to 0
at bootup. In such a case, each "pat" of the watchdog will reset the
timer to 0xffff. That's pretty short.
The input clock of the wdt can be any of a wide range of values. On
an rk3288 system, I've seen the wdt clock be 24.75 MHz. That means
each tick is ~40ns and we'll count to 0xffff in ~2.6ms.
Because of the above two facts, it's a really good idea to pat the
watchdog after initting the "top" register properly and before
enabling the watchdog. If you don't then there's no way we'll get the
next heartbeat in time.
Jisheng Zhang fixed this problem on some dw_wdt versions by using the
TOP_INIT feature. However, the dw_wdt on rk3288 doesn't have TOP_INIT
so it's a good idea to also pat the watchdog manually.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The watchdog functionality in both chips is almost identical to NCT6779.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Just like in case of other watchdog drivers, use the new kernel core
API to provide restart support.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
On some chips, like the TPS386000, the trigger cannot be disabled
and the CPU must keep toggling the line at all times. Add a switch
"always_running" to keep toggling the GPIO line regardless of the
state of the soft part of the watchdog. The "armed" member keeps
track of whether a timeout must also cause a reset.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Register a restart handler for the da9063 watchdog. System restart is
triggered by sending the shutdown command to the PMIC.
As more-suitable restart handlers may exist, the priority of the
watchdog restart handler is set to 128.
The actual restart method was inspired by a platform-specific patch from
the BSP by Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds a driver for the Mediatek SoC integrated
watchdog. This driver supports watchdog and software reset
for mt65xx and mt81xx SoCs.
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Tested-by: Eddie Huang <eddie.huang@mediatek.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This allows testing the watchdog easily with distros just by
doing pkill -9 watchdog.
Reported-by: Thomas Dziedzic <gostrc@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Replace device_reset() with devm_reset_control_get() + reset_control_deassert().
Make use of watchdog_init_timeout() instead of setting the timeout manually.
Signed-off-by: John Crispin <blogic@openwrt.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
allow_kdump was enabled as default since following commit.
commit a089361cf5,
watchdog: hpwdt: Unregister NMI events on exit.
But the initialization message was not modified.
So it still shows
HP Watchdog Timer Driver: NMI decoding initialized,
allow kernel dump: ON (default = 0/OFF) <=
This "default = 0/OFF" message may confuse users.
Fix it as "default = 1/ON".
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
IT8783 watchdog works as in IT872x
Tested on Adlink cPCI-6520 boards
Signed-off-by: Paolo Teti <paolo.teti@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const. Make struct
watchdog_ops const as well.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Disable power down counter of the watchdog to avoid system resets. The
watchdog power down counter is set automatically by the chip. If it is
not set to 0 in the driver, the system resets.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Improve power management operations(suspend and resume) as part of
dev_pm_ops for IMX2 watchdog driver.
If PM will be supported, please make sure that the wdev->clk
could disable the watchdog's counter input clock source or can
mask watchdog's reset request to the core.
If watchdog is still used by consumers and resumes from deep
sleep state, we need to restart the watchdog again without
enabling the timer.
If watchdog been has started --> stopped by the consumers and
resumes from non-deep sleep state, then start the timer again.
If watchdog has been started --> stopped by the consumers and
resumes from deep sleep state, will do nothing. The watchdog
will be restarted by consumers next time to be used.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Fix the following build warning by passing the expected argument type to
watchdog_active():
drivers/watchdog/imx2_wdt.c: In function 'imx2_wdt_suspend':
drivers/watchdog/imx2_wdt.c:340:2: warning: passing argument 1 of 'watchdog_active' from incompatible pointer type [enabled by default]
In file included from drivers/watchdog/imx2_wdt.c:38:0:
include/linux/watchdog.h:104:20: note: expected 'struct watchdog_device *' but argument is of type 'struct watchdog_device **'
Reported-by: Olof's autobuilder <build@lixom.net>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add power management operations(suspend and resume) as part of
dev_pm_ops for IMX2 watchdog driver.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
Pull timer core updates from Thomas Gleixner:
"The time(r) departement provides:
- more infrastructure work on the year 2038 issue
- a few fixes in the Armada SoC timers
- the usual pile of fixlets and improvements"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource: armada-370-xp: Use the reference clock on A375 SoC
watchdog: orion: Use the reference clock on Armada 375 SoC
clocksource: armada-370-xp: Add missing clock enable
time: Fix sign bug in NTP mult overflow warning
time: Remove timekeeping_inject_sleeptime()
rtc: Update suspend/resume timing to use 64bit time
rtc/lib: Provide y2038 safe rtc_tm_to_time()/rtc_time_to_tm() replacement
time: Fixup comments to reflect usage of timespec64
time: Expose get_monotonic_coarse64() for in-kernel uses
time: Expose getrawmonotonic64 for in-kernel uses
time: Provide y2038 safe mktime() replacement
time: Provide y2038 safe timekeeping_inject_sleeptime() replacement
time: Provide y2038 safe do_settimeofday() replacement
time: Complete NTP adjustment threshold judging conditions
time: Avoid possible NTP adjustment mult overflow.
time: Rename udelay_test.c to test_udelay.c
clocksource: sirf: Remove hard-coded clock rate
On Atmel AT91, the conversion to device tree is now considered complete,
and all machines that were not already converted in 3.18 are assumed to
be unused and dropped by the maintainer.
All remaining board files that were written in C are dropped, and the
ancient at91x40 sub-platform (based on an MMU-less ARM7) is removed
altogether. Cleaning up the last pieces was great fun, so I took the
time to do some of the coding myself and removed several hundred code
lines that ended up unused after the board files were done.
There are still a couple of AT91 specific device drivers that are not
converted to DT (CF, USB-OTG) and currently not working, and the platform
itself is not "multiplatform"-enabled, but both issues are going to be
taken care of in the 3.20 cycle.
This is split out from the other cleanups purely based on the size
of the branch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iD8DBQBUhyNX5t5GS2LDRf4RAnjxAKCER7eoLNadu1/93n/a9d1nUz4MoQCcCZUq
BolxCOi0wr4YTcQtp7rHzWI=
=ykAB
-----END PGP SIGNATURE-----
Merge tag 'at91-cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanup on mach-at91 from Arnd Bergmann:
"On Atmel AT91, the conversion to device tree is now considered
complete, and all machines that were not already converted in 3.18 are
assumed to be unused and dropped by the maintainer.
All remaining board files that were written in C are dropped, and the
ancient at91x40 sub-platform (based on an MMU-less ARM7) is removed
altogether. Cleaning up the last pieces was great fun, so I took the
time to do some of the coding myself and removed several hundred code
lines that ended up unused after the board files were done.
There are still a couple of AT91 specific device drivers that are not
converted to DT (CF, USB-OTG) and currently not working, and the
platform itself is not "multiplatform"-enabled, but both issues are
going to be taken care of in the 3.20 cycle.
This is split out from the other cleanups purely based on the size of
the branch"
* tag 'at91-cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (33 commits)
ARM: at91: remove unused board.h file
ARM: at91: remove unneeded header files
ARM: at91/clocksource: remove !DT PIT initializations
ARM: at91: at91rm9200 ST initialization is now DT only
ARM: at91: remove old AT91-specific drivers
ARM: at91: cleanup initilisation code by removing dead code
ARM: at91/Kconfig: select board files automatically
ARM: at91: remove unused IRQ function declarations
ARM: at91: remove legacy IRQ driver and related code
ARM: at91: remove old at91-specific clock driver
ARM: at91: remove clock data in at91sam9n12.c and at91sam9x5.c files
ARM: at91: remove all !DT related configuration options
ARM: at91/trivial: update Kconfig comment to mention SAMA5
ARM: at91: always USE_OF from now on
ARM: at91/Kconfig: remove ARCH_AT91RM9200 option for drivers
ARM: at91: switch configuration option to SOC_AT91RM9200
ARM: at91: remove at91rm9200 legacy board support
ARM: at91: remove at91rm9200 legacy boards files
ARM: at91/Kconfig: remove useless fbdev Kconfig options
ARM: at91: remove at91sam9261/at91sam9g10 legacy board support
...
Daniel Lezcano muttered:
* Marvell timer updates from Ezequiel Garcia
- Add missing clock enable calls for armada
- Change source clock for clocksource and watchdog
* SIRF timer updates from Yanchang Li
- Make clock rate configurable
The precise selection is useless, so we simply remove these dependencies.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
The 25 MHz reference clock has better stability so its use is prefered over the
core clock. Change the Armada 375 clock initialization to use this reference
clock. To ensure the driver is compatible with an old devicetree, also provide
a fallback path which will silently return to the previous behavior.
While here, add the clock specification to the binding documentation.
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
This patch removes the magic value used for rebooting the board. This
value is useless and leads to a static checker warning as reported by
Dan Carpenter.
Signed-off-by: Carlo Caione <carlo@caione.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
They need HAS_IOMEM, so let them depend on it, the related error (with
allmodconfig under um):
MODPOST 1205 modules
ERROR: "devm_ioremap_resource" [drivers/watchdog/tegra_wdt.ko] undefined!
ERROR: "devm_ioremap_resource" [drivers/watchdog/of_xilinx_wdt.ko] undefined!
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds support for the watchdog hardware found in A31 and
newer SoCs. This new hardware has registers at different offsets, and
the system reset control has been split out of the "mode" register
into a new "configuration" register.
Differences not supported by this driver include separate interrupt
lines for each watchdog, instead of sharing an interrupt line and
registers with the timer block.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds support for hardware parameters tied to compatible
strings, so similar hardware can reuse the driver.
This will be used to support the newer watchdog found in A31 and
later SoCs. Differences in the new hardware include separate
interrupt lines for each watchdog, and corresponding interrupt
control/status registers. Watchdog control registers were also
slightly rearranged.
Also replace ioread32()/iowrite32() with readl()/writel() in various
places changed.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Register the watchdog as the system restart function
to the new introducing kernel restart call chain in the
driver instead of providing the restart in machine desc.
This restart handler function is from the mxc_restart()
in arch/arm/mach-imx/system.c
Signed-off-by: Jingchang Lu <jingchang.lu@freescale.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The WDT's BITE_TIME warm-reset behavior can be leveraged as a last
resort mechanism for triggering chip reset. Usually, other restart
methods (such as PS_HOLD) are preferrable for issuing a more complete
reset of the chip. As such, keep the priority of the watchdog notifier
low.
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
On a lot of Samsung systems the watchdog is responsible for restarting the
system and until now this code was contained in plat-samsung/watchdog-reset.c.
With the introduction of the restart handlers, this code can now move into
driver itself, removing the need for arch-specific code.
Tested on a S3C2442 based GTA02
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The kernel core now provides an API to trigger a system restart.
Register with it to support restarting the system via. watchdog.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds the watchdog driver for the Amlogic Meson SoCs used also
to reboot the device.
Signed-off-by: Carlo Caione <carlo@caione.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
There is no conflict with rtc/rtc-stmp3xxx.c parent
because modified registers in PM functions of stmp3xxx_rtc_wdt
are different.
Signed-off-by: Janusz Uzycki <j.uzycki@elproma.com.pl>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This driver supports the watchdog device inside the DA9063 PMIC.
Signed-off-by: Krystian Garbaciak <krystian.garbaciak@diasemi.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Tested-by: Steve Twiss <stwiss.opensource@diasemi.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This adds a driver for the watchdog timer available in Ricoh RN5T618
PMIC. The device supports a programmable expiration time of 1, 8, 32
or 128 seconds.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Exynos7 SoC has a Watchdog for Atlas (A57) cores
This patch adds support for the Atlas watchdog.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add a driver for the watchdog timer block found in the Krait Processor
Subsystem (KPSS) on the MSM8960, APQ8064, and IPQ8064.
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The TOP_INIT, ie bit 4-7 of the WDOG_TIMEOUT_RANGE_REG_OFFSET register
may be zero, so the timeout period may be very short after initialization
is done, thus the system may be reset soon after enabling. We fix this
problem by also initialising the TOP_INIT when setting TOP in function
dw_wdt_set_top().
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add Cadence WDT driver. This is used by Xilinx Zynq.
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
There is no need to store the return value of misc_deregister() in a
variable. Instead we can just return the value directly.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Building booke_wdt fails when trying to build as a module as there is no
early_param() in module. Fix by using module_param() instead of early_param().
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
There is no need to init .owner field.
Based on the patch from Peter Griffin <peter.griffin@linaro.org>
"mmc: remove .owner field for drivers using module_platform_driver"
This patch removes the superflous .owner field for drivers which
use the module_platform_driver API, as this is overriden in
platform_driver_register anyway."
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Boris BREZILLON