Add the SL2 interface IP block and interconnect data. The SL2 is related
to the IVA-HD subsystem.
Add IP block and interconnect data for the C2C ("Chip-to-chip")
interconnect. This can provide a direct system interconnect link to
other devices stacked on the OMAP package.
Add the ELM IP block and interconnect data. The ELM can be used
to locate errors in NAND flash connected to the GPMC.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Add the McASP hwmod and associated interconnect data. The McASP is a
general-purpose audio serial port.
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add the Slimbus hwmods and associated interconnect data. The Slimbus
IP blocks implement a two-wire serial interface.
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add the GPU hwmod and associated interconnect data. The GPU is a
graphics accelerator.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Add the EMIF1 and 2 hwmods and associated interconnect data. The EMIFs
are SDRAM interface IP blocks.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Add the GPMC hwmod and associated interconnect data. The GPMC is a
programmable parallel-bus memory controller.
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add the HDQ/1-wire hwmod and associated interconnect data. The
HDQ/1-wire IP block is a low-speed serial interconnect.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Add hwmod data for the OMAP4 FDIF IP block.
This patch also includes a change (originally from Fernando Guzman
Lugo <fernando.lugo@ti.com>) to set a softreset delay for the FDIF IP
block:
http://www.spinics.net/lists/arm-kernel/msg161874.html
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Acked-by: Benoît Cousson <b-cousson@ti.com>
Cc: Fernando Guzman Lugo <fernando.lugo@ti.com>
[paul@pwsan.com: rearranged to match script output; fixed FDIF end address to
match script data; wrote trivial changelog; combined the FDIF portion of
Fernando's srst_udelay patch]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Reorganize the hwmod data to declare the IP blocks first and the
interconnects second. This allows us to remove the forward
declarations, which this patch also does. Saves some lines of source
data. While here, take the opportunity to synchronize the order of
the OMAP44xx hwmod data with the autogenerator output -- it's slightly
different due to past mismerges -- and fix a few minor typos and
whitespace problems in the files.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Register interconnect links between IP blocks, rather than the IP
blocks themselves. (The IP blocks will be registered as a side-effect
of registering the links.)
The objective is to reduce the number of lines of static data and
facilitate the sharing of IP block data between different SoCs. These
objectives come at the penalty of increased boot time due to increased
computation.
While here, fix a few whitespace problems and inaccurate variable names.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Some hwmods were commented out from the OMAP4 data, under the theory
that they shouldn't be added until drivers were ready. But part of
the utility of the hwmod code is that it can reset and properly
initialize IP blocks that have no drivers associated with them.
Rather than commenting the links in the future hwmod data conversion
patches, discussing this with Benoit, it seems best to simply
uncomment them now.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
One of the OMAP4 links was missing OCP_USER flags, since it was only
used by the DSP initiator, and we did not have an OCP_USER_DSP flag.
Future patches will switch the hwmod code and data to register
interfaces, rather than hwmods, and it will be mandatory for all
interfaces to have at least one user bit set. This patch resolves the
issue by adding OCP_USER_DSP and marking the DSP-IVA interface
appropriately.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Commit 407a6888f7 ("OMAP4: hwmod data:
Add AESS, McPDM, bandgap, counter_32k, MMC, KBD, ISS & IPU") adds a
hwmod for the bandgap die temperature sensor IP block. This IP block
has no interconnect port or firewall region, nor does it have an
independent register space or OCP control registers. Its registers
are embedded in the System Control Module (SCM) IP block. So it
appears that the bandgap device should be created by the SCM driver.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Remove the pseudo-hwmods associated with hardreset lines from the
OMAP4 data file. Future patches will convert this data to register
hwmods by interfaces, rather than registering hwmods directly. The
pseudo-hwmods aren't associated with any interfaces, so this will
create a problem.
After this change, the hwmod code will reset processor IPs at the
hwmod level, rather than by individual hardreset lines. So, for
example, if the IVA device driver code wishes to place one of the
sequencer cores into reset, while leaving the other active, it must do
so itself by calling the appropriate PRM functions.
This patch will cause a change in the initialization behavior of the
DSP, IVA, and IPU.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Due to HW limitation, some IPs should not be accessed just after a
softreset. Since the current hwmod sequence is accessing the sysconfig
register just after the reset, it might lead to OCP bus error in
that case.
Add a new field in the sysconfig structure to specify a delay in usecs
needed after doing a softreset.
In the case of the ISS and FDIF modules, the L3 OCP port will be
disconnected upon a SW reset. That issue was confirmed with HW simulation
and an errata should be available soon. The HW recommendation to avoid
that is to wait for 100 OCP clk cycles, before accessing the IP.
Considering the worse case (OPP50), the L3 bus will run at 100 MHz,
so a 1 usec delay is needed. Add an x2 margin to be safe.
Acked-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Fernando Guzman Lugo <fernando.lugo@ti.com>
[paul@pwsan.com: dropped FDIF change for now since the hwmod data is not
yet upstream; the FDIF change will need to be added later once the FDIF
data is merged]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
CLKS signal for McBSP ports can be selected from internal (PRCM) or
external (ABE_CLKS pin) source. To be able to use existing code we
need to create clock aliases consistent among OMAP2/3/4.
Based on a patch from Péter Ujfalusi <peter.ujfalusi@ti.com>;
the patch description above is his.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Péter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Conflicts:
arch/arm/mach-lpc32xx/clock.c
arch/arm/mach-pxa/pxa25x.c
arch/arm/mach-pxa/pxa27x.c
The conflicts with pxa are non-obvious, we have multiple branches
adding and removing the same clock settings. According to
Haojian Zhuang, removing the sa1100 rtc dummy clock is the correct
fix here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
arch/arm/mach-omap2/: included some headers tiwce:
- arch/arm/mach-omap2/board-ldp.c: 'linux/gpio.h'
- arch/arm/mach-omap2/io.c: 'common.h'
- arch/arm/mach-omap2/omap_hwmod_44xx_data.c: 'plat/i2c.h'
Remove the duplicates.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
To set sr ntarget values for all volt_domain,
volt_table is retrieved by doing a look_up of 'vdd_name'
field from omap_hwmod but voltage domain pointer does not
belong to omap_hwmod and is not used anywhere else.
As a part of voltage layer and SR Layer clean up volt
pointer is removed from omap_hwmod and added in dev
attributes of SR. The value of the field must match
the voltage domain names for the binding to be effective.
Tested on OMAP3630 SDP, OMAP3530 Beagleboard and
OMAP4430 SDP Board.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Shweta Gulati <shweta.gulati@ti.com>
Acked by: Nishanth Menon <nm@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
To be able to get the memory resources by name from
the DMIC driver (for MPU and for DMA).
Without this patch, functionality that was working in 3.2 breaks in
3.3-rc1. This patch should have gone in as part of the 3.3 merge
window, but was inadvertently missed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[paul@pwsan.com: added commit message note]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
For I2C clockactivity field is added for OMAP3 and OMAP4 that defines how the
interface (OCP) and functional (system) clocks behave when the I2C module is
idle.
The configuration of the clock activity bit field (per TRM) is as follows:
0x0: Both clocks can be cut off
0x1: Only OCP clock must be kept active; system clock
can be cut off
0x3: Both clocks must be kept active
0x2: Only system clock must be kept active; OCP clock
can be cut off
The patch makes 0x2(CLOCKACT_TEST_ICLK) the default for OMAP3 and OMAP4.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Following 2 hwmod structures are added
1. usb_host_hs
The hwmod of usbhs with uhh, ehci and ohci base addresses
functional clock and ehci, ohci irqs
2. usb_tll_hs
hwmod of usbhs with the TLL base address and irq.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
[keshava_mgowda@ti.com: rebased to kernel version 3.0, added workarounds for
hardware issues]
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Reviewed-by: Partha Basak <parthab@india.ti.com>
[paul@pwsan.com: fixed multi-line comments, fixed whitespace, fixed S-o-b
notes, removed spurious TLL->L3 interface]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Resetting DISPC when a DISPC output is enabled causes the DSS to go into an
inconsistent state. Thus if the bootloader has enabled a display, the hwmod code
cannot reset the DISPC module just like that, but the outputs need to be
disabled first.
Add function dispc_disable_outputs() which disables all active overlay manager
and ensure all frame transfers are completed.
Modify omap_dss_reset() to call this function and clear DSS_CONTROL,
DSS_SDI_CONTROL and DSS_PLL_CONTROL so that DSS is in a clean state when the
DSS2 driver starts.
This resolves the hang issue(caused by a L3 error during boot) seen on the
beagle board C3, which has a factory bootloader that enables display. The issue
is resolved with this patch.
Thanks to Tomi and Sricharan for some additional testing.
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: R, Sricharan <r.sricharan@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
[paul@pwsan.com: restructured code, removed omap_{read,write}l(), removed
cpu_is_omap*() calls and converted to dev_attr]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This patch adds a custom DSS reset function used on OMAPs from OMAP2
forward.
The function doesn't actually do a reset, it only waits for the reset to
complete. The reason for this is that on OMAP4 there is no possibility
to do a SW reset, and on OMAP2/3 doing a SW reset for dss_core resets
all the other DSS modules also, thus breaking the HWMOD model where
every DSS module is handled independently.
This fixes the problem with DSS reset on OMAP4, caused by the fact that
because there's no SW reset for dss_core on OMAP4, the HWMOD framework
doesn't try to reset dss_core and thus the DSS clocks were never enabled
at the same time. This causes causes the HWMOD reset to fail for
dss_dispc and dss_rfbi.
The common reset function will also allow us to fix another problem in
the future: before doing a reset we need to disable DSS outputs, which
are in some cases enabled by the bootloader, as otherwise DSS HW seems
to get more or less stuck, requiring a power reset to recover.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
[paul@pwsan.com: modified to build arch/arm/mach-omap2/display.o
unconditionally to avoid an error when !CONFIG_OMAP2_DSS]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The OMAP4 HWMOD data currently contains errors with DSS clocks:
dss_hdmi and dss_venc have their main_clks wrong. The clocks should be
dss_48mhz_clk and dss_tv_clk, respectively.
These problems were temporarily fixed with the DSS patches
9ede365aa6 ("HACK: OMAP: DSS2: clk hack
for OMAP2/3"), and df5d3ed23c ("OMAP:
DSS2: HDMI: fix hdmi clock name"), which can be reverted after this
patch.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
DSS needs all DSS clocks to be enabled to be able to finish reset
properly. Before v3.1-rc1 the omapdss driver was managing clocks and
resets correctly. However, when omapdss started using runtime PM at
v3.1-rc1, the responsibility for the reset moved to HWMOD framework.
HWMOD framework does not currently enable all the DSS clocks when
resetting the DSS hardware. This causes the HWMOD frameworks boot-time
reset to fail, possibly leaving the DSS hardware in undefined state.
This patch sets HWMOD_CONTROL_OPT_CLKS_IN_RESET for dss_core. The flag
is actually not used on OMAP4, because dss_core hardware does not have
soft-reset functionality and thus the HWMOD framework never resets nor
waits for the reset to finish.
However, while the flag is not strictly needed currently, I think it
represents the HW correctly: all the DSS clocks should be enabled after
power-on to allow DSS hardware to finish its reset.
A custom reset function will be added in the following patches which
manages this correctly for OMAP4.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Remove the dss_dss_clk from dss_core's opt-clocks. dss_dss_clk already
defined as the dss main_clk, and thus is not needed as an opt-clock.
Remove opt-clocks for dss_dispc, as dispc only uses the main_clk.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add routines to converts dmtimers to platform devices. The device data
is obtained from hwmod database of respective platform and is registered
to device model after successful binding to driver.
In addition, capability attribute of each of the timers is added in
hwmod database.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Thara Gopinath <thara@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Cousson, Benoit <b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
At Tony's request, remove the OMAP_CHIP* flags from the hwmod data, and
replace it instead with chip family, variant, and ES level-specific lists
of hwmods to register.
Thanks to Gražvydas Ignotas <notasas@gmail.com> for finding a bug in the
AM3517/3505 support, and for other review comments.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Gražvydas Ignotas <notasas@gmail.com>
Add a new field to provide the mode supported by the module.
The mode will control the way mandatory clocks are managed by the PRCM.
0 : Module is temporarily disabled by SW. OCP access to module are stalled.
Can be used to change timing parameter of GPMC module.
1 : Module is managed automatically by HW according to clock domain
transition. A clock domain sleep transition put module into idle.
A wakeup domain transition put it back into function.
If CLKTRCTRL=3, any OCP access to module is always granted.
Module clocks may be gated according to the clock domain state.
2 : Module is explicitly enabled. Interface clock (if not used for
functions) may be gated according to the clock domain state.
Functional clocks are guarantied to stay present. As long as
in this configuration, power domain sleep transition cannot happen.
Some modules will have a modulemode initialized at 1 (HWCTRL) by default.
This is the case for interconnect and simple module like GPIO, WDT, MAILBOX.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add a 'context_offs' entry in the prcm.omap4 structure to all
IPs when applicable.
The offset will be used to retrieve the per module context lost
information now available on OMAP4.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The RSTCTRL register was accessed using an absolute address.
The usage of hardcoded macros to calculate virtual address from physical
one should be avoided as much as possible.
The usage of an offset will allow future improvement like migration from
the current architecture code toward a module driver.
Update prm_xxx accessors, move definition to the proper header file and
update copyrights.
Change the s16 register offset parameter to u16.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: use '_prminst_' in function names that are part of the
prminst44xx.c file]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The CLKCTRL register was accessed using an absolute address.
The usage of hardcoded macros to calculate virtual address from physical
one should be avoided as much as possible.
The usage of a offset will allow future improvement like migration from
the current architecture code toward a module driver.
Update cm_xxx accessor, move definition to the proper header file and
update copyrights.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Todd Poynor <toddpoynor@google.com>
[paul@pwsan.com: renamed 'omap4_cm_' fns to 'omap4_cminst_'; removed empty
fn prototype section from cm44xx.h; incorporated comments from Todd;
documented some functions]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
In OMAP PRCM terminology, the clock domain is defined as a group of IPs
that share some clocks and most of the time an interface clock.
Every IP does belong to a clockdomain.
For the moment the clock domain attribute is affected to a clock node.
The issue with that approach, is that a clock might or not belong to a
clock domain. Moreover during module transition, it is up to a module
to handle properly the clock domain state and not to a clock node.
Create a clkdm_name attribute to provide this information per hwmod.
Populate this attribute for every OMAP4 hwmod entries.
Future cleanup series with remove that information from the OMAP4 clock
when it is relevant.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: fix the mpuss_clkdm name]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The sequence of _ocp_softreset doesn't work for i2c. The i2c module has a
special sequence to reset the module. The sequence is
- Disable the I2C.
- Write to SOFTRESET bit.
- Enable the I2C.
- Poll on the RESETDONE bit.
The sequence is implemented as a function and the i2c_class is updated with
the correct 'reset' pointer. omap_hwmod_softreset function is implemented
which triggers the softreset by writing into sysconfig register. On following
this sequence, i2c module resets properly and timeouts are not seen.
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Avinash.H.M <avinashhm@ti.com>
[paul@pwsan.com: combined this patch with a patch to remove
HWMOD_INIT_NO_RESET from the 44xx hwmod flags; change register
offset conditional code to use the IP block revision; minor code
cleanup]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This adds the new functionality flags for omap i2c unit to all OMAP2
hwmod definitions
Cc: patches@linaro.org
Cc: Ben Dooks <ben-linux@fluff.org>
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andy Green <andy.green@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Since we cannot trust (or even reliably find) the OMAP I2C
peripheral unit's own revision register, we must inform the
OMAP i2c driver of which IP version it is running on. We
do this by tagging the omap_hwmod_class for i2c on all the
OMAP2+ platform / cpu specific hwmod init and passing it up
to the driver (next patches).
Cc: patches@linaro.org
Cc: Ben Dooks <ben-linux@fluff.org>
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andy Green <andy.green@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Peter Maydell noticed when running under QEMU he was getting
errors reporting 32-bit access to I2C peripheral unit registers
that are documented to be 8 or 16-bit only[1][2]
The I2C driver is blameless as it wraps its accesses in a
function using __raw_writew and __raw_readw, it turned out it
is the hwmod stuff.
However the hwmod code already has a flag to force a
perhipheral unit to only be accessed using 16-bit operations.
This patch applies the 16-bit only flag to the 2430,
OMAP3xxx and OMAP44xx hwmod structs. 2420 was already
correctly marked up as 16-bit.
The 2430 change will need testing by TI as arranged
in the comments to the previous patch version.
When the 16-bit flag is or-ed with other flags, it is placed
first as requested in comments.
[1] OMAP4430 Technical reference manual section 23.1.6.2
[2] OMAP3530 Techincal reference manual section 18.6
Cc: patches@linaro.org
Cc: Ben Dooks <ben-linux@fluff.org>
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andy Green <andy.green@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Currently using pm_runtime with DSS requires the DSS driver to enable
the DSS functional clock before calling pm_runtime_get(). That makes it
impossible to use pm_runtime in DSS as it is meant to be used, with
pm_runtime callbacks.
This patch changes the hwmod database for OMAP4 so that enabling the
hwmod via pm_runtime will also enable the DSS functional clock, allowing
us to use pm_runtime properly in DSS driver.
The DSS HWMOD side is not really correct, not before nor after this
patch, and getting DSS to retention will probably not work currently.
However, it is not supported in the mainline kernel anyway, so this
won't break anything.
So this patch allows us to write the pm_runtime adaptation for the DSS
driver the way it should be done, and the HWMOD/PM side can be fixed
later.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add missing DSS optional clocks to HWMOD data for OMAP4xxx.
Add HWMOD_CONTROL_OPT_CLKS_IN_RESET flag for dispc to fix dispc reset.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
[b-cousson@ti.com: Remove a comment and update the subject]
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
[paul@pwsan.com: removed DSS "fck" role and some clkdev aliases at Tomi's
request]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The interconnect modules were using a slightly different layout than
the regular modules.
Align the layout for better consitency.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Fix .prcm alignement and usb_otg_hs class and hwmod structures.
Add a couple of more potential hwmods in the comment.
Remove hsi, since it is already included in the data.
Remove one blank line.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
A couple of parens were added around some flags.
Remove them, since they are not needed and not used
for any other hwmods.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Change the position of the ocp_if structure to match the template.
Remove unneeded comma at the end of address space flag field.
Remove USER_SDMA since this ocp link is only from the l3_main_1
path that is accessible only from the MPU in that case and not
the SDMA.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Previously, struct omap_hwmod_dma_info arrays were unterminated; and
users of these arrays used the ARRAY_SIZE() macro to determine the
length of the array. However, ARRAY_SIZE() only works when the array
is in the same scope as the macro user.
So far this hasn't been a problem. However, to reduce duplicated
data, a subsequent patch will move common data to a separate, shared
file. When this is done, ARRAY_SIZE() will no longer be usable.
This patch removes ARRAY_SIZE() usage for struct omap_hwmod_dma_info
arrays and uses a sentinel value (irq == -1) as the array terminator
instead.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Previously, struct omap_hwmod_mpu_irqs arrays were unterminated; and
users of these arrays used the ARRAY_SIZE() macro to determine the
length of the array. However, ARRAY_SIZE() only works when the array
is in the same scope as the macro user.
So far this hasn't been a problem. However, to reduce duplicated
data, a subsequent patch will move common data to a separate, shared
file. When this is done, ARRAY_SIZE() will no longer be usable.
This patch removes ARRAY_SIZE() usage for struct omap_hwmod_mpu_irqs
arrays and uses a sentinel value (irq == -1) as the array terminator
instead.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Paul Walmsley