According the JEDEC specification an eMMC card supporting 1.8V vccq in DDR
mode should also be capable of 3.3V. However, it's been reported that some
mmc hosts supports 3.3V, but not 1.8V.
Currently the mmc core implements an error handling when the host fails to
set 1.8V for vccq, by falling back to 3.3V. Unfortunate, this seems to be
insufficient for some mmc hosts. To enable these to use eMMC DDR mode let's
invent a new mmc cap, MMC_CAP_3_3V_DDR, which tells whether they support
the eMMC 3.3V DDR mode.
In case MMC_CAP_3_3V_DDR is set, but not MMC_CAP_1_8V_DDR, let's change to
remain on the 3.3V, as it's the default voltage level for vccq, set by the
earlier power up sequence.
As this change introduces MMC_CAP_3_3V_DDR, let's take the opportunity to
do some re-formatting of the related defines in the header file.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Jan Glauber <jglauber@cavium.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Earlier the mmc_set_signal_voltage() existed, but since it has been renamed
to mmc_set_uhs_voltage(), we can now use that name instead.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Jan Glauber <jglauber@cavium.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
The mmc_set_signal_voltage() function is used for SD/SDIO when switching to
1.8V for UHS mode. To clarify this let's do the following changes.
- We are always providing MMC_SIGNAL_VOLTAGE_180 as the signal_voltage
parameter to the function. Then, let's just remove the parameter as it
serves no purpose.
- Rename the function to mmc_set_uhs_voltage().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Jan Glauber <jglauber@cavium.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
The mmc_set_signal_voltage() function is used for SD/SDIO when switching to
1.8V for UHS mode. Therefore let's remove the redundant code dealing with
MMC_SIGNAL_VOLTAGE_330.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Jan Glauber <jglauber@cavium.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
In the case of a single clock source, you don't need names. However,
if the controller has 2 clock sources, you need to name them correctly
so the driver can find the 2nd one. The 2nd clock is for the internal
card detect logic.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Rob Herring <robh@kernel.org>
Some controllers have 2 clock sources instead of 1. The 2nd clock
is for the internal card detect logic and must be enabled/disabled
along with the main core clock for proper operation.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cleanup some debug prints that cause needless noise
during normal usage.
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc_blk_issue_rq() function is called in exactly one place
in queue.c and there the return value is ignored. So the
functions called from that function that also meticulously
return 0/1 do so for no good reason.
Error reporting on the asynchronous requests are done upward to
the block layer when the requests are eventually completed or
fail, which may happen during the flow of the mmc_blk_issue_*
functions directly (for "special commands") or later, when an
asynchronous read/write request is completed.
The issuing functions do not give rise to errors on their own,
and there is nothing to return back to the caller in queue.c.
Drop all return values and make the function return void.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Recycling the same variable in an x=x+1 fashion may seem
clever here but it makes the code terse and hard to follow
for humans. Introduce a new_areq and old_areq variable so
we see what is going on.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Setting rqc to NULL followed by a goto to cmd_abort is just a way
to do unconditional abort without starting any new command.
Inline the calls to mmc_blk_rw_cmd_abort() and return immediately
in those cases.
Add some comments to the code flow so it is clear that this is
where the asynchronous requests come back in and the result of
them gets handled.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The code in mmc_blk_issue_rq_rq() aborts a command if the request
is not properly aligned on large sectors. As part of the path
jumping out, it assigns the local variable mq_rq reflecting
a MMC queue request to the current MMC queue request, which is
confusing since the variable is not used after this jump.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As a step toward breaking apart the very complex function
mmc_blk_issue_rw_rq() we break out the code to start a new
request.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As a first step toward breaking apart the very complex function
mmc_blk_issue_rw_rq() we break out the command abort code.
This code assumes "ret" is != 0 and then repeatedly hammers
blk_end_request() until the request to the block layer to end
the request succeeds.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use the bitops API instead of shifting directly.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove the sdhci-s3c-regs.h file.
Instead, it located those defined values into sdhci-s3c.c.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Before enabling SDIO irqs, clear the status bit, so we discard old and
stale interrupts. Needed to get two wireless cards working. Use the
newly introduced macro in all places.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
QUIRK sounds like there is something wrong, but actually there are just
some bits which need to be 1. Rename it to be more clear.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
tmio_mmc_sdio_irq() is not used as a seperate irq handler anymore, so we
can make it similar to the other irq helper functions, namely:
* only give the host as argument function which is what it really needs
* prefix function name with __
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Allow power sequencing for the Marvell SD8787 Wifi/BT chip.
This can be abstracted to other chipsets if needed in the future.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Matt Ranostay <matt@ranostay.consulting>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Create a helper function to disable clocks and use it in remove(), too.
Now, clk_summary in debugfs reports the clocks as disabled and
unprepared after unbinding.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This provides enhanced_strobe mode feature support in sdhci-msm
driver.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
During tuning execution for HS400 mode, HW sequence recommends
to select MCLK_SEL/2(0x3) in VENDOR_SPEC & sdhc msm clock at GCC
to be 400MHZ (nearest supported clk). Add this change in tuning
sequence during HS400 tuning.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Clear SDHCI_HS400_TUNING flag after platform_execute_tuning
so that platform_execute_tuning may use it if needed.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Program CORE_CSR_CDC_DELAY_CFG for hardware recommended 1.25ns delay.
We may see data CRC errors if it's programmed for any other delay
value.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The vendor specific func register doesn't get reset when using the
software reset register. The various bootloader's could leave this
in an unknown state, hence reset this register to it's power on reset
value during probe.
Signed-off-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Factor out sdhci_msm_hs400 used for DLL calibration in HS400
modes. This function will be needed for enhanced_strobe as well.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Factor out msm_set/get_clock_rate_for_bus_mode for it's later
use in changing the tuning sequence for selecting HS400
bus speed mode.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This factors out sdhci_msm_hc_select_mode to later use
it during enhanced_strobe mode select.
It also further breaks sdhci_msm_hc_select_mode
into separate functions for configuring HS400 mode
or other modes.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch implements support for multiblock transfers bounded
by SET_BLOCK_COUNT (CMD23) on the MXS MMC host driver.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
host->dma_addr can store a value that is not returned by the DMA API,
so it is safer to check if is a valid DMA address indirectly.
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
With commit 67bf5156ed ("gpio / ACPI: fix returned error from
acpi_dev_gpio_irq_get()"), mmc_gpiod_request_cd() returns -EPROBE_DEFER if
GPIO is not ready when sdhci-acpi driver is probed, and sdhci-acpi driver
should be probed again later in this case.
This fixes an order issue when both GPIO and sdhci-acpi drivers are built
as modules.
CC: stable@vger.kernel.org # v4.9
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=177101
Tested-by: Jonas Aaberg <cja@gmx.net>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Using extern when declaring functions in the public header, core.h, is
redundant. Let's just remove the use of it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
A significant amount of functions are available through the public mmc
host.h header file. Let's slim down this public mmc interface, as to
prevent users from abusing it, by moving some of the functions to private
mmc host.h header file.
This change concentrates on moving the functions into private mmc headers,
following changes may continue with additional clean-ups.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
A significant amount of functions and other definitions are available
through the public mmc card.h header file. Let's slim down this public mmc
interface, as to prevent users from abusing it, by moving some of the
functions/definitions to private mmc header files.
This change concentrates on moving the functions into private mmc headers,
following changes may continue with additional clean-ups.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
The mmc_card_present() function helps the mmc core to track an internal
state of the card device. More importantly, it's not intended to be used by
mmc host drivers to check for an inserted card. Therefore, let's stop using
it and instead rely on checking for a valid pointer to a struct mmc_card,
as it should be good enough.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
The mmc_card_present() function helps the mmc core to track an internal
state of the card device. More importantly, it's not intended to be used by
mmc host drivers to check for an inserted card. Therefore, let's stop using
it and instead rely on checking for a valid pointer to a struct mmc_card,
as it should be good enough.
Cc: linux-omap@vger.kernel.org
Cc: Tony Lindgren <tony@atomide.com>
Cc: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
The struct _mmc_csd isn't being used and has been lurking around for a
while. Let's kill it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
As the public mmc.h header already contains similar defines for other mmc
commands and arguments, let's move those for erase/trim/discard into here
as well.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Ideally the public mmc header file, core.h, shouldn't contain interfaces
particularly intended to be used by host drivers. Instead those should
remain in the host.h header file. Therefore, let's move a couple functions
from core.h to host.h.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
A significant amount of functions are available through the public mmc
core.h header file. Let's slim down this public mmc interface, as to
prevent users from abusing it, by moving some of the functions to private
mmc header files.
This change concentrates on moving the functions into private mmc headers,
following changes may continue with additional clean-ups, as an example
some functions can be turned into static.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
This is the first step in cleaning up the private mmc header files. In this
change we makes sure each header file builds standalone, as that helps to
resolve dependencies.
While changing this, it also seems reasonable to stop including other
headers from inside a header itself which it don't depend upon.
Additionally, in some cases such dependencies are better resolved by
forward declaring the needed struct.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
This is the first step in cleaning up the public mmc header files. In this
change we makes sure each header file builds standalone, as that helps to
resolve dependencies.
While changing this, it also seems reasonable to stop including other
headers from inside a header itself which it don't depend upon.
Additionally, in some cases such dependencies are better resolved by
forward declaring the needed struct.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
I got this new build error on today's linux-next
drivers/mmc/host/s3cmci.h:69:24: error: field 'pio_tasklet' has incomplete type
struct tasklet_struct pio_tasklet;
drivers/mmc/host/s3cmci.c: In function 's3cmci_enable_irq':
drivers/mmc/host/s3cmci.c:390:4: error: implicit declaration of function 'enable_irq';did you mean 'enable_imask'? [-Werror=implicit-function-declaration]
While I haven't found out why this happened now and not earlier, the
solution is obvious, we should include the header that defines
the structure.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MIPS Alchemy db1300 dev board depends on interrupt.h. Explicitly
include it instead of relying on the public mmc header host.h.
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: <linux-mips@linux-mips.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
The davinci board omapl138-hawk, depends on interrupt.h. Explicitly include
it instead of relying on the public mmc header host.h.
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@kernel.org>
Cc: <linux-arm-kernel@lists.infradead.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Some of the davinci boards, da850-evm, dm644x-evm and neuros-osd2 depends
on leds.h. Explicitly include it instead of relying on the public mmc
header host.h.
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@kernel.org>
Cc: <linux-arm-kernel@lists.infradead.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Some of the pxa platforms, balloon3, colibri-pxa270-income, corgi,
trizeps4, vpac270, zeus and zylonite depends on leds.h. Explicitly include
it instead of relying on the public mmc header host.h.
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: <linux-arm-kernel@lists.infradead.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
This patch fix some spelling typo found in devicetree/bindings/mmc.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ulf Hansson