Improves dcache footprint by ensuring that fewer cache lines need to be
touched.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This speeds up the function in case a station already exists by avoiding
calling an expensive kzalloc just to free it again after the next check.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These functions drifts TSF timers, not TBTT.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mesh_sync_offset_adjust_tbtt() implements Extensible synchronization
framework ([1] 13.13.2 Extensible synchronization framework). It shall
not operate the flag "TBTT Adjusting subfield" ([1] 8.4.2.100.8 Mesh
Capability), since it is used only for MBCA ([1] 13.13.4 Mesh beacon
collision avoidance, see 13.13.4.4.3 TBTT scanning and adjustment
procedures for detail). So this patch remove the flag operations.
[1] IEEE Std 802.11 2012
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
[remove adjusting_tbtt entirely, since it's now unused]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a new "global" (i.e. not per-rfkill device) LED trigger, rfkill-any,
which may be useful on laptops with a single "radio LED" and multiple
radio transmitters. The trigger is meant to turn a LED on whenever
there is at least one radio transmitter active and turn it off
otherwise.
This requires taking rfkill_global_mutex before calling rfkill_set_block()
in rfkill_resume(): since __rfkill_any_led_trigger_event() is called from
rfkill_set_block() unconditionally, each caller of the latter needs to
take care of locking rfkill_global_mutex.
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use a separate label per error condition in rfkill_init() to make it a
bit cleaner and easier to extend.
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Could be useful for debugging memory consumption issues,
and perhaps power-save as well.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previously, kernel sends NEW_PEER_CANDIDATE event to user land even if
the found peer does not have any room to accept other peer. This causes
continuous connection trials.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the ability for an AP (and associated VLANs) to perform
multicast-to-unicast conversion for ARP, IPv4 and IPv6 frames
(possibly within 802.1Q). If enabled, such frames are to be sent
to each station separately, with the DA replaced by their own
MAC address rather than the group address.
Note that this may break certain expectations of the receiver,
such as the ability to drop unicast IP packets received within
multicast L2 frames, or the ability to not send ICMP destination
unreachable messages for packets received in L2 multicast (which
is required, but the receiver can't tell the difference if this
new option is enabled.)
This also doesn't implement the 802.11 DMS (directed multicast
service).
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
[use true/false, rename label to the correct "multicast",
use __be16 for ethertype and network order for constants]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 4a733ef1be (mac80211: remove PM-QoS listener) removed all use
of 'beaconint_us' from ieee80211_recalc_ps() but left the variable
intact. Compiling with W=1 gives the following warning, fix it.
net/mac80211/mlme.c: In function ‘ieee80211_recalc_ps’:
net/mac80211/mlme.c:1481:7: warning: variable ‘beaconint_us’ set but not used [-Wunused-but-set-variable]
iee80211_tu_to_usec has no side-effects and is safe to remove.
Fixes: 4a733ef1be ("mac80211: remove PM-QoS listener")
Cc: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kirtika Ruchandani <kirtika@chromium.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit b1bce14a79 (mac80211: update opmode when adding new station)
refactored ieee80211_vht_handle_opmode into __ieee80211_vht_handle_opmode
and ieee80211_vht_handle_opmode leaving a set but unused variable
(sband) in the former. Compiling with W=1 gives the following warning,
fix it.
net/mac80211/vht.c: In function ‘__ieee80211_vht_handle_opmode’:
net/mac80211/vht.c:424:35: warning: variable ‘sband’ set but not used [-Wunused-but-set-variable]
Remove 'struct ieee80211_local* local' as well, it was only used to
set sband.
This is a harmless warning, and is only being fixed to reduce the
noise with W=1 in the kernel.
Fixes: b1bce14a79 ("mac80211: update opmode when adding new station")
Cc: Marek Kwaczynski <marek.kwaczynski@tieto.com>
Cc: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kirtika Ruchandani <kirtika@chromium.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 633e271326 (mac80211: split sched scan IEs) introduced the
len variable to keep track of the return value of
ieee80211_build_preq_ies() but did not use it. Compiling with W=1
gives the following warning, fix it.
net/mac80211/scan.c: In function ‘__ieee80211_request_sched_scan_start’:
net/mac80211/scan.c:1123:9: warning: variable ‘len’ set but not used [-Wunused-but-set-variable]
This is a harmless warning and is only being fixed to reduce the noise
with W=1 in the kernel.
Fixes: 633e271326 ("mac80211: split sched scan IEs")
Cc: David Spinadel <david.spinadel@intel.com>
Cc: Alexander Bondar <alexander.bondar@intel.com>
Cc: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kirtika Ruchandani <kirtika@chromium.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 5bcae31d9 (mac80211: implement multi-vif in-place reservations)
introduced ieee80211_vif_use_reserved_switch() with a counter variable
'i' that is set but not used. Compiling with W=1 gives the following
warning, fix it.
net/mac80211/chan.c: In function ‘ieee80211_vif_use_reserved_switch’:
net/mac80211/chan.c:1273:6: warning: variable ‘i’ set but not used [-Wunused-but-set-variable]
This is a harmless warning, and is only being fixed to reduce the
noise obtained with W=1 in the kernel.
Fixes: 5bcae31d9 ("mac80211: implement multi-vif in-place reservations")
Cc: Michal Kazior <michal.kazior@tieto.com>
Cc: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kirtika Ruchandani <kirtika@chromium.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 3b17fbf87d introduced sta_get_expected_throughput()
leaving variable 'struct rate_control_ref* ref' set but unused.
Compiling with W=1 gives the following warning, fix it.
net/mac80211/sta_info.c: In function ‘sta_set_sinfo’:
net/mac80211/sta_info.c:2052:27: warning: variable ‘ref’ set but not used [-Wunused-but-set-variable]
Fixes: 3b17fbf87d ("mac80211: mesh: Add support for HW RC implementation")
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Maxim Altshul <maxim.altshul@ti.com>
Signed-off-by: Kirtika Ruchandani <kirtika@google.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit f027c2aca0 introduced 'rates_idx' in
ieee80211_tx_status_noskb but did not use it. Compiling with W=1
gives the following warning, fix it.
mac80211/status.c: In function ‘ieee80211_tx_status_noskb’:
mac80211/status.c:636:6: warning: variable ‘rates_idx’ set but not used [-Wunused-but-set-variable]
This is a harmless warning, and is only being fixed to reduce the
noise generated with W=1.
Fixes: f027c2aca0 ("mac80211: add ieee80211_tx_status_noskb")
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kirtika Ruchandani <kirtika@google.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 554891e63a introduced 'struct ieee80211_rx_status' in
ieee80211_rx_h_defragment but did not use it. Compiling with W=1
gives the following warning, fix it.
net/mac80211/rx.c: In function ‘ieee80211_rx_h_defragment’:
net/mac80211/rx.c:1911:30: warning: variable ‘status’ set but not used [-Wunused-but-set-variable]
Fixes: 554891e63a ("mac80211: move packet flags into packet")
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Kirtika Ruchandani <kirtika@google.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There is no need to prevent toggling multicast_to_unicast while
interface is already up. This change simplifies reconfiguration
from hostapd.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The presence of the NL80211_ATTR_SCHED_SCAN_INTERVAL attribute was
checked in nl80211_parse_sched_scan() and
nl80211_parse_sched_scan_plans() which might be a bit redundant
so removing one.
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The comment on the name indirection suggested an issue but turned out
to be untrue. Digging in older kernel version showed issue with ipw2x00
but that is no longer true so get rid on the name indirection.
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Simplify the two conditions gating the schedule_work() into
a single one and get rid of the additional exit point from
the function in doing so.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Guenter Roeck (1):
cris: Only build flash rescue image if CONFIG_ETRAX_AXISFLASHMAP is selected
Paul Bolle (1):
cris: No need to append -O2 and $(LINUXINCLUDE)
Paul Gortmaker (1):
tty: serial: make crisv10 explicitly non-modular
arch/cris/boot/compressed/Makefile | 3 ---
arch/cris/boot/rescue/Makefile | 9 +++++++--
drivers/tty/serial/crisv10.c | 6 ++----
3 files changed, 9 insertions(+), 9 deletions(-)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iEYEABECAAYFAlhJbl0ACgkQ31LbvUHyf1cK3QCfTFKWF21o02/H8ZFby6oa7Jgp
X4kAn0+rFwV0CtJ3JQum49DsHZf/M72+
=iH+I
-----END PGP SIGNATURE-----
Merge tag 'cris-for-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/jesper/cris
Pull CRIS updates from Jesper Nilsson:
"Three patches for minor issues"
* tag 'cris-for-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/jesper/cris:
cris: No need to append -O2 and $(LINUXINCLUDE)
tty: serial: make crisv10 explicitly non-modular
cris: Only build flash rescue image if CONFIG_ETRAX_AXISFLASHMAP is selected
-----BEGIN PGP SIGNATURE-----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=5/rC
-----END PGP SIGNATURE-----
Merge tag 'openrisc-for-linus' of git://github.com/openrisc/linux
Pull Openrisc updates from Stafford Horne:
- changes to MAINTAINER for openrisc
- probably biggest actual change is the move to memblock from bootmem
- ... plus several bug and build fixes
* tag 'openrisc-for-linus' of git://github.com/openrisc/linux:
openrisc: prevent VGA console, fix builds
openrisc: include l.swa in check for write data pagefault
openrisc: Updates after openrisc.net has been lost
openrisc: Consolidate setup to use memblock instead of bootmem
openrisc: remove the redundant of_platform_populate
openrisc: add NR_CPUS Kconfig default value
openrisc: Support both old (or32) and new (or1k) toolchain
openrisc: Add thread-local storage (TLS) support
openrisc: restore all regs on rt_sigreturn
openrisc: fix PTRS_PER_PGD define
- Use seq_puts() for fixed strings.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=aHq2
-----END PGP SIGNATURE-----
Merge tag 'm68k-for-v4.10-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
Pull m68k updates from Geert Uytterhoeven:
"Use seq_puts() for fixed strings"
* tag 'm68k-for-v4.10-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k/atari: Use seq_puts() in atari_get_hardware_list()
m68k/amiga: Use seq_puts() in amiga_get_hardware_list()
Pull AVR32 updates from Hans-Christian Noren Egtvedt.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/egtvedt/linux-avr32:
avr32: wire up pkey syscalls
AVR32-pio: Replace two seq_printf() calls by seq_puts() in pio_bank_show()
AVR32-pio: Use seq_putc() in pio_bank_show()
AVR32-clock: Combine nine seq_printf() calls into one call in clk_show()
AVR32-clock: Use seq_putc() in two functions
Pull m68knommu updates from Greg Ungerer:
"There are two sets of changes in this pull.
The largest is the addition of the ColdFire platform side i2c support
(the IO addressing, setup and clock definitions). The i2c hardware
module itself is driven by the kernels existing iMX i2c driver.
The other change is the addition of support for the Amcore board"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: AMCORE board, add iMX i2c support
m68k: add Sysam AMCORE open board support
m68knommu: platform support for i2c devices on ColdFire SoC
Pull sparc updates from David Miller:
"Just a bunch of small cleanups and fixes here, and support for user
probes from Allen Pais"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc: fix a building error reported by kbuild
sparc64: fix typo in pgd_clear()
sparc64: restore irq in error paths in iommu
sparc: leon: Fix a retry loop in leon_init_timers()
sparc64: make string buffers large enough
sparc64: move dereference after check for NULL
sparc: kernel: use builtin_platform_driver
sparc64:Support User Probes for sparc
Pull networking updates from David Miller:
1) Platform regulatory domain support for ath10k, from Bartosz
Markowski.
2) Centralize min/max MTU checking, thus removing tons of duplicated
code all of the the various drivers. From Jarod Wilson.
3) Support ingress actions in act_mirred, from Shmulik Ladkani.
4) Improve device adjacency tracking, from David Ahern.
5) Add support for LED triggers on PHY link state changes, from Zach
Brown.
6) Improve UDP socket memory accounting, from Paolo Abeni.
7) Set SK_MEM_QUANTUM to a fixed size of 4096, instead of PAGE_SIZE.
From Eric Dumazet.
8) Collapse TCP SKBs at retransmit time even if the right side SKB has
frags. Also from Eric Dumazet.
9) Add IP_RECVFRAGSIZE and IPV6_RECVFRAGSIZE cmsgs, from Willem de
Bruijn.
10) Support routing by UID, from Lorenzo Colitti.
11) Handle L3 domain binding (ie. VRF) for RAW sockets, from David
Ahern.
12) tcp_get_info() can run lockless, from Eric Dumazet.
13) 4-tuple UDP hashing in SFC driver, from Edward Cree.
14) Avoid reorders in GRO code, from Eric Dumazet.
15) IPV6 Segment Routing support, from David Lebrun.
16) Support MPLS push and pop for L3 packets in openvswitch, from Jiri
Benc.
17) Add LRU datastructure support for BPF, Martin KaFai Lau.
18) VF support in liquidio driver, from Raghu Vatsavayi.
19) Multiqueue support in alx driver, from Tobias Regnery.
20) Networking cgroup BPF support, from Daniel Mack.
21) TCP chronograph measurements, from Francis Yan.
22) XDP support for qed driver, from Yuval Mintz.
23) BPF based lwtunnels, from Thomas Graf.
24) Consistent FIB dumping to offloading drivers, from Ido Schimmel.
25) Many optimizations for UDP under high load, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1522 commits)
netfilter: nft_counter: rework atomic dump and reset
e1000: use disable_hardirq() for e1000_netpoll()
i40e: don't truncate match_method assignment
net: ethernet: ti: netcp: add support of cpts
net: phy: phy drivers should not set SUPPORTED_[Asym_]Pause
net: l2tp: ppp: change PPPOL2TP_MSG_* => L2TP_MSG_*
net: l2tp: deprecate PPPOL2TP_MSG_* in favour of L2TP_MSG_*
net: l2tp: export debug flags to UAPI
net: ethernet: stmmac: remove private tx queue lock
net: ethernet: sxgbe: remove private tx queue lock
net: bridge: shorten ageing time on topology change
net: bridge: add helper to set topology change
net: bridge: add helper to offload ageing time
net: nicvf: use new api ethtool_{get|set}_link_ksettings
net: ethernet: ti: cpsw: sync rates for channels in dual emac mode
net: ethernet: ti: cpsw: re-split res only when speed is changed
net: ethernet: ti: cpsw: combine budget and weight split and check
net: ethernet: ti: cpsw: don't start queue twice
net: ethernet: ti: cpsw: use same macros to get active slave
net: mvneta: select GENERIC_ALLOCATOR
...
OpenRISC does not support VGA console, so prevent that kconfig symbol
from being enabled for OpenRISC, thus fixing these build errors:
drivers/built-in.o: In function `vgacon_save_screen':
vgacon.c:(.text+0x20e0): undefined reference to `screen_info'
vgacon.c:(.text+0x20e8): undefined reference to `screen_info'
drivers/built-in.o: In function `vgacon_init':
vgacon.c:(.text+0x284c): undefined reference to `screen_info'
vgacon.c:(.text+0x2850): undefined reference to `screen_info'
drivers/built-in.o: In function `vgacon_startup':
vgacon.c:(.text+0x28d8): undefined reference to `screen_info'
drivers/built-in.o:vgacon.c:(.text+0x28f0): more undefined references to `screen_info' follow
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Chen Gang <gang.chen@asianux.com>
Cc: Jonas Bonn <jonas@southpole.se>
Signed-off-by: Stafford Horne <shorne@gmail.com>
During page fault handling we check the last instruction to understand
if the fault was for a read or for a write. By default we fall back to
read. New instructions were added to the openrisc 1.1 spec for an
atomic load/store pair (l.lwa/l.swa).
This patch adds the opcode for l.swa (0x33) allowing it to be treated as
a write operation.
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
[shorne@gmail.com: expanded a bit on the comment]
Signed-off-by: Stafford Horne <shorne@gmail.com>
The openrisc.net domain expired and was taken over by squatters.
These updates point documentation to the new domain, mailing lists
and git repos.
Also, Jonas is not the main maintainer anylonger, he reviews changes
but does not maintain a repo or sent pull requests. Updating this to
add Stafford and Stefan who are the active maintainers.
Acked-by: Olof Kindgren <olof.kindgren@gmail.com>
Signed-off-by: Stafford Horne <shorne@gmail.com>
Clearing out one todo item. Use the memblock boot time memory
which is the current standard.
Tested-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jonas <jonas@southpole.se>
Signed-off-by: Stafford Horne <shorne@gmail.com>
The of_platform_populate call in the openrisc arch code is now redundant
as the DT core provides a default call. Openrisc has a NULL match table
which means only top level nodes with compatible strings will have
devices creates. The default version will also descend nodes in the
match table such as "simple-bus" which should be fine as openrisc
doesn't have any of these (though it is preferred that memory-mapped
peripherals be grouped under a bus node(s)).
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Jonas Bonn <jonas@southpole.se>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Stafford Horne <shorne@gmail.com>
The build system now expects that NR_CPUS is defined.
Follow 4cbbbb4 ("microblaze: Fix missing NR_CPUS in menuconfig")
Signed-off-by: Stafford Horne <shorne@gmail.com>
The output file format for or1k has changed from "elf32-or32"
to "elf32-or1k". Select the correct output format automatically
to be able to compile the kernel with both toolchain variants.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Stafford Horne <shorne@gmail.com>
Historically OpenRISC GCC has reserved r10 which we now use to hold
the thread pointer for thread-local storage (TLS).
Signed-off-by: Christian Svensson <blue@cmd.nu>
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Stafford Horne <shorne@gmail.com>
Fix signal handling for when signals are handled as the result of timers
or exceptions, previous code assumed syscalls. This was noticeable with X
crashing where it uses SIGALRM.
This patch restores all regs before returning to userspace via
_resume_userspace instead of via syscall return path.
The rt_sigreturn syscall is more like a context switch than a function
call; it entails a return from one context (the signal handler) to another
(the process in question). For a context switch like this there are
effectively no call-saved regs that remain constant across the transition.
Reported-by: Sebastian Macke <sebastian@macke.de>
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Tested-by: Guenter Roeck <linux@roeck-us.net>
[shorne@gmail.com: Updated comment better reflect change and issue]
Signed-off-by: Stafford Horne <shorne@gmail.com>
On OpenRISC, with its 8k pages, PAGE_SHIFT is defined to be 13.
That makes the expression (1UL << (PAGE_SHIFT-2)) evaluate
to 2048.
The correct value for PTRS_PER_PGD should be 256.
Correcting the PTRS_PER_PGD define unveiled a bug in map_ram(),
where PTRS_PER_PGD was used when the intent was to iterate
over a set of page table entries.
This patch corrects that issue as well.
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Acked-by: Jonas Bonn <jonas@southpole.se>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Stafford Horne <shorne@gmail.com>
Strings which did not contain data format specifications should be put
into a sequence. Thus use the corresponding function "seq_puts".
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
A single character (line break) should be put into a sequence.
Thus use the corresponding function "seq_putc".
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Some data were printed into a sequence by nine separate function calls.
Print the same data by a single function call instead.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
A single character (line break) should be put into two sequences.
Thus use the corresponding function "seq_putc".
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
>> arch/sparc/include/asm/topology_64.h:44:44:
error: implicit declaration of function 'cpu_data'
[-Werror=implicit-function-declaration]
#define topology_physical_package_id(cpu) (cpu_data(cpu).proc_id)
^
Let's include cpudata.h in topology_64.h.
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: sparclinux@vger.kernel.org
Suggested-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It really has to be pgdp, not pgd.
It just happend to work since all callers have 'pgd' as an argument.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some error paths where we should restore IRQs but we don't.
Fixes: bb620c3d39 ("sparc: Make sparc64 use scalable lib/iommu-common.c functions")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original code causes a static checker warning because it has a
continue inside a do { } while (0); loop. In that context, a continue
and a break are equivalent. The intent was to go back to the start of
the loop so the continue was a bug.
I've added a retry label at the start and changed the continue to a goto
retry. Then I removed the do { } while (0) loop and pulled the code in
one indent level.
Fixes: 2791c1a439 ("SPARC/LEON: added support for selecting Timer Core and Timer within core")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
My static checker complains that if "lvl" is ULONG_MAX (this is 64 bit)
then some of the strings will overflow. I don't know if that's possible
but it seems simple enough to make the buffers slightly larger.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We shouldn't dereference "iommu" until after we have checked that it is
non-NULL.
Fixes: f08978b0fd ("sparc64: Enable sun4v dma ops to use IOMMU v2 APIs")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use builtin_platform_driver() helper to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Eric Saint Etienne <eric.saint.etienne@oracle.com>
Signed-off-by: Allen Pais <allen.pais@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Felix Fietkau