>From : Woojung Huh <woojung.huh@microchip.com>
Add functions to unregister phy fixup for modules.
int phy_unregister_fixup(const char *bus_id, u32 phy_uid, u32 phy_uid_mask)
Unregister phy fixup from phy_fixup_list per bus_id, phy_uid &
phy_uid_mask
int phy_unregister_fixup_for_uid(u32 phy_uid, u32 phy_uid_mask)
Unregister phy fixup from phy_fixup_list.
Use it for fixup registered by phy_register_fixup_for_uid()
int phy_unregister_fixup_for_id(const char *bus_id)
Unregister phy fixup from phy_fixup_list.
Use it for fixup registered by phy_register_fixup_for_id()
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently always sets the PBLx8/PBLx4 bit, which means that
the pbl values configured via the pbl/txpbl/rxpbl DT properties are
always multiplied by 8/4 in the hardware.
In order to allow the DT to configure lower pbl values, while at the
same time not changing behavior of any existing device trees using the
pbl/txpbl/rxpbl settings, add a property to disable the multiplication
of the pbl by 8/4 in the hardware.
Suggested-by: Rabin Vincent <rabinv@axis.com>
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GMAC and newer supports independent programmable burst lengths for
DMA tx/rx. Add new optional devicetree properties representing this.
To be backwards compatible, snps,pbl will still be valid, but
snps,txpbl/snps,rxpbl will override the value in snps,pbl if set.
If the IP is synthesized to use the AXI interface, there is a register
and a matching DT property inside the optional stmmac-axi-config DT node
for controlling burst lengths, named snps,blen.
However, using this register, it is not possible to control tx and rx
independently. Also, this register is not available if the IP was
synthesized with, e.g., the AHB interface.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
snps,tso was previously placed under AXI BUS Mode parameters,
suggesting that the property should be in the stmmac-axi-config node.
TSO (TCP Segmentation Offloading) has nothing to do with AXI BUS Mode
parameters, and the parser actually expects it to be in the root node,
not in the stmmac-axi-config.
Also added a note about snps,tso only being available on GMAC4 and newer.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains a large Netfilter update for net-next,
to summarise:
1) Add support for stateful objects. This series provides a nf_tables
native alternative to the extended accounting infrastructure for
nf_tables. Two initial stateful objects are supported: counters and
quotas. Objects are identified by a user-defined name, you can fetch
and reset them anytime. You can also use a maps to allow fast lookups
using any arbitrary key combination. More info at:
http://marc.info/?l=netfilter-devel&m=148029128323837&w=2
2) On-demand registration of nf_conntrack and defrag hooks per netns.
Register nf_conntrack hooks if we have a stateful ruleset, ie.
state-based filtering or NAT. The new nf_conntrack_default_on sysctl
enables this from newly created netnamespaces. Default behaviour is not
modified. Patches from Florian Westphal.
3) Allocate 4k chunks and then use these for x_tables counter allocation
requests, this improves ruleset load time and also datapath ruleset
evaluation, patches from Florian Westphal.
4) Add support for ebpf to the existing x_tables bpf extension.
From Willem de Bruijn.
5) Update layer 4 checksum if any of the pseudoheader fields is updated.
This provides a limited form of 1:1 stateless NAT that make sense in
specific scenario, eg. load balancing.
6) Add support to flush sets in nf_tables. This series comes with a new
set->ops->deactivate_one() indirection given that we have to walk
over the list of set elements, then deactivate them one by one.
The existing set->ops->deactivate() performs an element lookup that
we don't need.
7) Two patches to avoid cloning packets, thus speed up packet forwarding
via nft_fwd from ingress. From Florian Westphal.
8) Two IPVS patches via Simon Horman: Decrement ttl in all modes to
prevent infinite loops, patch from Dwip Banerjee. And one minor
refactoring from Gao feng.
9) Revisit recent log support for nf_tables netdev families: One patch
to ensure that we correctly handle non-ethernet packets. Another
patch to add missing logger definition for netdev. Patches from
Liping Zhang.
10) Three patches for nft_fib, one to address insufficient register
initialization and another to solve incorrect (although harmless)
byteswap operation. Moreover update xt_rpfilter and nft_fib to match
lbcast packets with zeronet as source, eg. DHCP Discover packets
(0.0.0.0 -> 255.255.255.255). Also from Liping Zhang.
11) Built-in DCCP, SCTP and UDPlite conntrack and NAT support, from
Davide Caratti. While DCCP is rather hopeless lately, and UDPlite has
been broken in many-cast mode for some little time, let's give them a
chance by placing them at the same level as other existing protocols.
Thus, users don't explicitly have to modprobe support for this and
NAT rules work for them. Some people point to the lack of support in
SOHO Linux-based routers that make deployment of new protocols harder.
I guess other middleboxes outthere on the Internet are also to blame.
Anyway, let's see if this has any impact in the midrun.
12) Skip software SCTP software checksum calculation if the NIC comes
with SCTP checksum offload support. From Davide Caratti.
13) Initial core factoring to prepare conversion to hook array. Three
patches from Aaron Conole.
14) Gao Feng made a wrong conversion to switch in the xt_multiport
extension in a patch coming in the previous batch. Fix it in this
batch.
15) Get vmalloc call in sync with kmalloc flags to avoid a warning
and likely OOM killer intervention from x_tables. From Marcelo
Ricardo Leitner.
16) Update Arturo Borrero's email address in all source code headers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The cyclecounter mult and shift values can be calculated based on the
CPTS rfclk frequency and timekeepnig framework provides required algos
and API's.
Hence, calc mult and shift basing on CPTS rfclk frequency if both
cpts_clock_shift and cpts_clock_mult properties are not provided in DT (the
basis of calculation algorithm is borrowed from
__clocksource_update_freq_scale() commit 7d2f944a2b ("clocksource:
Provide a generic mult/shift factor calculation")). After this change
cpts_clock_shift and cpts_clock_mult DT properties will become optional.
Cc: John Stultz <john.stultz@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add three reset control signals, "mac_core_rst", "mac_ifc_rst" and
"phy_rst".
The following diagram explained how the reset signals work.
SoC
|-----------------------------------------------------
| ------ |
| | cpu | |
| ------ |
| | |
| ------------ AMBA bus |
| GMAC | |
| ---------------------- |
| ------------- mac_core_rst | -------------- | |
| |clock and |-------------->| mac core | | |
| |reset | | -------------- | |
| |generator |---- | | | |
| ------------- | | ---------------- | |
| | ---------->| mac interface | | |
| | mac_ifc_rst | ---------------- | |
| | | | | |
| | | ------------------ | |
| |phy_rst | | RGMII interface | | |
| | | ------------------ | |
| | ---------------------- |
|----------|------------------------------------------|
| |
| ----------
|--------------------- |PHY chip |
----------
The "mac_core_rst" represents "mac core reset signal", it resets
the mac core including packet processing unit, descriptor processing unit,
tx engine, rx engine, control unit.
The "mac_ifc_rst" represents "mac interface reset signal", it resets
the mac interface. The mac interface unit connects mac core and
data interface like MII/RMII/RGMII. After we set a new value of
interface mode, we must reset mac interface to reload the new mode value.
The "mac_core_rst" and "mac_ifc_rst" are both optional to be
backward compatible with the hix5hd2 SoC.
The "phy_rst" represents "phy reset signal", it does a hardware reset
on the PHY chip. This reset signal is optional if the PHY can work well
without the hardware reset.
Add one more clock signal, the existing is MAC core clock,
and the new one is MAC interface clock.
The MAC interface clock is optional to be backward compatible with
the hix5hd2 SoC.
Signed-off-by: Dongpo Li <lidongpo@hisilicon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "hix5hd2" is SoC name, add the generic ethernet driver name.
The "hisi-gemac-v1" is the basic version and "hisi-gemac-v2" adds
the SG/TXCSUM/TSO/UFO features.
Signed-off-by: Dongpo Li <lidongpo@hisilicon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2016-12-03
Here's a set of Bluetooth & 802.15.4 patches for net-next (i.e. 4.10
kernel):
- Fix for a potential NULL deref in the ieee802154 netlink code
- Fix for the ED values of the at86rf2xx driver
- Documentation updates to ieee802154
- Cleanups to u8 vs __u8 usage
- Timer API usage cleanups in HCI drivers
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This switch (default on) can be used to disable automatic registration
of connection tracking functionality in newly created network
namespaces.
This means that when net namespace goes down (or the tracker protocol
module is unloaded) we *might* have to unregister the hooks.
We can either add another per-netns variable that tells if
the hooks got registered by default, or, alternatively, just call
the protocol _put() function and have the callee deal with a possible
'extra' put() operation that doesn't pair with a get() one.
This uses the latter approach, i.e. a put() without a get has no effect.
Conntrack is still enabled automatically regardless of the new sysctl
setting if the new net namespace requires connection tracking, e.g. when
NAT rules are created.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Implemented RFC7527 Enhanced DAD.
IPv6 duplicate address detection can fail if there is some temporary
loopback of Ethernet frames. RFC7527 solves this by including a random
nonce in the NS messages used for DAD, and if an NS is received with the
same nonce it is assumed to be a looped back DAD probe and is ignored.
RFC7527 is enabled by default. Can be disabled by setting both of
conf/{all,interface}/enhanced_dad to zero.
Signed-off-by: Erik Nordmark <nordmark@arista.com>
Signed-off-by: Bob Gilligan <gilligan@arista.com>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEES2FAuYbJvAGobdVQPTuqJaypJWoFAlhAJY0THG1rbEBwZW5n
dXRyb25peC5kZQAKCRA9O6olrKklam88B/0dgD2R9D8udVyHnp1CGVrWm+REER49
g6V2ZqIqfxaAFEiQFIhySJJtWYt4vHAC2A3Mwx6yyv9qugYb26LCiSt3XQPlPNY4
yVFpVzOMsFjmSu9PQ7u47b7/IKmqmSuuuQQWm3rDxDQC+KLKmH1TfULXzqDQ/yR/
+gNTvi6Zwfi6rFU7B33I6cT0VhfnWXhbAbBdg4jNmW5WAyz+WT6c9J9oXQMRw5VW
ESTYrU2c+IVK3Z3e0BOmnCytaPrxE6j1OmT0LNsVR5aoXDmK3jDNln/7cPEOCkD3
3t9ub+gqfeaMIjyDI3yBcy75Gjk3mFQMXs/3LVTivwZySgGldOak/iyL
=vXN1
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-4.10-20161201' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2016-12-01
this is a pull request of 4 patches for net-next/master.
There are two patches by Chris Paterson for the rcar_can and rcar_canfd
device tree binding documentation. And a patch by Geert Uytterhoeven
that corrects the order of interrupt specifiers.
The fourth patch by Colin Ian King fixes a spelling error in the
kvaser_usb driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix english in documentation, make documentation match reality, remove
options that were removed from code.
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Couple conflicts resolved here:
1) In the MACB driver, a bug fix to properly initialize the
RX tail pointer properly overlapped with some changes
to support variable sized rings.
2) In XGBE we had a "CONFIG_PM" --> "CONFIG_PM_SLEEP" fix
overlapping with a reorganization of the driver to support
ACPI, OF, as well as PCI variants of the chip.
3) In 'net' we had several probe error path bug fixes to the
stmmac driver, meanwhile a lot of this code was cleaned up
and reorganized in 'net-next'.
4) The cls_flower classifier obtained a helper function in
'net-next' called __fl_delete() and this overlapped with
Daniel Borkamann's bug fix to use RCU for object destruction
in 'net'. It also overlapped with Jiri's change to guard
the rhashtable_remove_fast() call with a check against
tc_skip_sw().
5) In mlx4, a revert bug fix in 'net' overlapped with some
unrelated changes in 'net-next'.
6) In geneve, a stale header pointer after pskb_expand_head()
bug fix in 'net' overlapped with a large reorganization of
the same code in 'net-next'. Since the 'net-next' code no
longer had the bug in question, there was nothing to do
other than to simply take the 'net-next' hunks.
Signed-off-by: David S. Miller <davem@davemloft.net>
Armada 3700 is a new ARMv8 SoC from Marvell using same network controller
as older Armada 370/38x/XP. There are however some differences that
needed taking into account when adding support for it:
* open default MBUS window to 4GB of DRAM - Armada 3700 SoC's Mbus
configuration for network controller has to be done on two levels:
global and per-port. The first one is inherited from the
bootloader. The latter can be opened in a default way, leaving
arbitration to the bus controller. Hence filled mbus_dram_target_info
structure is not needed
* make per-CPU operation optional - Recent patches adding RSS and XPS
support for Armada 38x/XP enabled per-CPU operation of the controller
by default. Contrary to older SoC's Armada 3700 SoC's network
controller is not capable of per-CPU processing due to interrupt lines'
connectivity. This patch restores non-per-CPU operation, which is now
optional and depends on neta_armada3700 flag value in mvneta_port
structure. In order not to complicate the code, separate interrupt
subroutine is implemented.
For now, on the Armada 3700, RSS is disabled as the current
implementation depend on the per cpu interrupts.
[gregory.clement@free-electrons.com: extract from a larger patch, replace
some ifdef and port to net-next for v4.10]
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric says: "By looking at tcpdump, and TS val of xmit packets of multiple
flows, we can deduct the relative qdisc delays (think of fq pacing).
This should work even if we have one flow per remote peer."
Having random per flow (or host) offsets doesn't allow that anymore so add
a way to turn this off.
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
This is a large batch of Netfilter fixes for net, they are:
1) Three patches to fix NAT conversion to rhashtable: Switch to rhlist
structure that allows to have several objects with the same key.
Moreover, fix wrong comparison logic in nf_nat_bysource_cmp() as this is
expecting a return value similar to memcmp(). Change location of
the nat_bysource field in the nf_conn structure to avoid zeroing
this as it breaks interaction with SLAB_DESTROY_BY_RCU and lead us
to crashes. From Florian Westphal.
2) Don't allow malformed fragments go through in IPv6, drop them,
otherwise we hit GPF, patch from Florian Westphal.
3) Fix crash if attributes are missing in nft_range, from Liping Zhang.
4) Fix arptables 32-bits userspace 64-bits kernel compat, from Hongxu Jia.
5) Two patches from David Ahern to fix netfilter interaction with vrf.
From David Ahern.
6) Fix element timeout calculation in nf_tables, we take milliseconds
from userspace, but we use jiffies from kernelspace. Patch from
Anders K. Pedersen.
7) Missing validation length netlink attribute for nft_hash, from
Laura Garcia.
8) Fix nf_conntrack_helper documentation, we don't default to off
anymore for a bit of time so let's get this in sync with the code.
I know is late but I think these are important, specifically the NAT
bits, as they are mostly addressing fallout from recent changes. I also
read there are chances to have -rc8, if that is the case, that would
also give us a bit more time to test this.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
According to both DTS (example and actual files), and Linux driver code,
the first interrupt specifier should be the Channel interrupt, while the
second interrupt specifier should be the Global interrupt.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch exports the sender chronograph stats via the socket
SO_TIMESTAMPING channel. Currently we can instrument how long a
particular application unit of data was queued in TCP by tracking
SOF_TIMESTAMPING_TX_SOFTWARE and SOF_TIMESTAMPING_TX_SCHED. Having
these sender chronograph stats exported simultaneously along with
these timestamps allow further breaking down the various sender
limitation. For example, a video server can tell if a particular
chunk of video on a connection takes a long time to deliver because
TCP was experiencing small receive window. It is not possible to
tell before this patch without packet traces.
To prepare these stats, the user needs to set
SOF_TIMESTAMPING_OPT_STATS and SOF_TIMESTAMPING_OPT_TSONLY flags
while requesting other SOF_TIMESTAMPING TX timestamps. When the
timestamps are available in the error queue, the stats are returned
in a separate control message of type SCM_TIMESTAMPING_OPT_STATS,
in a list of TLVs (struct nlattr) of types: TCP_NLA_BUSY_TIME,
TCP_NLA_RWND_LIMITED, TCP_NLA_SNDBUF_LIMITED. Unit is microsecond.
Signed-off-by: Francis Yan <francisyyan@gmail.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This updates some out of date documentation and fixes some wrong assumptions as
well as pure grammar fixes. This file needs to move towards the new kernel doc
system and getting an overhaul during this work.
Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add links to the IEEE 802.3-2008 document, and the RGMII v1.3 and v2.0
revisions of the standard.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RGMII is a recurring source of pain for people with Gigabit Ethernet
hardware since it may require PHY driver and MAC driver level
configuration hints. Document what are the expectations from PHYLIB and
what options exist.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Describe that the Ethernet MAC controller is ultimately responsible for
dealing with proper pause frames/flow control advertisement and
enabling, and that it is therefore allowed to have it change
phydev->supported/advertising with SUPPORTED_Pause and
SUPPORTED_AsymPause.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the function pointers documentation which duplicates information
found in include/linux/phy.h. Maintaining documentation about two
different locations just does not work, but the code is less likely to
be outdated.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RGMII requires special RX and/or TX delays depending on the actual
hardware circuit/wiring. These delays can be added by the MAC, the PHY
or the designer of the circuit (the latter means that no delay has to
be added by PHY or MAC).
There are 4 RGMII phy-modes used describe where a delay should be
applied:
- rgmii: the RX and TX delays are either added by the MAC (where the
exact delay is typically configurable, and can be turned off when no
extra delay is needed) or not needed at all (because the hardware
wiring adds the delay already). The PHY should neither add the RX nor
TX delay in this case.
- rgmii-rxid: configures the PHY to enable the RX delay. The MAC should
not add the RX delay in this case.
- rgmii-txid: configures the PHY to enable the TX delay. The MAC should
not add the TX delay in this case.
- rgmii-id: combines rgmii-rxid and rgmii-txid and thus configures the
PHY to enable the RX and TX delays. The MAC should neither add the RX
nor TX delay in this case.
Document these cases in the ethernet.txt documentation to make it clear
when to use each mode.
If applied incorrectly one might end up with MAC and PHY both enabling
for example the TX delay, which breaks ethernet TX traffic on 1000Mbit/s
links.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Major changes:
iwlwifi
* finalize and enable dynamic queue allocation
* use dev_coredumpmsg() to prevent locking the driver
* small fix to pass the AID to the FW
* use FW PS decisions with multi-queue
ath9k
* add device tree bindings
* switch to use mac80211 intermediate software queues to reduce
latency and fix bufferbloat
wl18xx
* allow scanning in AP mode
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJYOAC4AAoJEG4XJFUm622bUYkH/3SSYp6moSdKpVnVPx7ST7yK
t9WHR9IMZFIhD6vq8AK6+8OQr1TgGjHfPu+WZj7CIl8nu53kcgPRi51gg1mndbNg
9N3RbVp06nGbM2VnW8ZIpg3OLIXatZ4c9g3LFvvtyobYvWGJ6W4D79JdlmTG1ELr
XAjInbxFsgon+CwqCMOaAJx8xYp42rBnPRZZvhOq9O33kRw8Umo9UQw0s1U2Vfgx
prxQ6d0GxNAPEe8QiDw/vtBcXWFMOhQeDl8sK70ZcojSn1FY730NsIh/Y86PcQTK
6TsvOL5gg+rd0ln8TZRAslnDrZBAhTEDqUzLQMRJ9VjEj5RFd8eLCSIzHfaroI8=
=4qCH
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2016-11-25' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.10
Major changes:
iwlwifi
* finalize and enable dynamic queue allocation
* use dev_coredumpmsg() to prevent locking the driver
* small fix to pass the AID to the FW
* use FW PS decisions with multi-queue
ath9k
* add device tree bindings
* switch to use mac80211 intermediate software queues to reduce
latency and fix bufferbloat
wl18xx
* allow scanning in AP mode
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ath.git patches for 4.10. Major changes:
ath9k
* add device tree bindings
* switch to use mac80211 intermediate software queues to reduce
latency and fix bufferbloat
All conflicts were simple overlapping changes except perhaps
for the Thunder driver.
That driver has a change_mtu method explicitly for sending
a message to the hardware. If that fails it returns an
error.
Normally a driver doesn't need an ndo_change_mtu method becuase those
are usually just range changes, which are now handled generically.
But since this extra operation is needed in the Thunder driver, it has
to stay.
However, if the message send fails we have to restore the original
MTU before the change because the entire call chain expects that if
an error is thrown by ndo_change_mtu then the MTU did not change.
Therefore code is added to nicvf_change_mtu to remember the original
MTU, and to restore it upon nicvf_update_hw_max_frs() failue.
Signed-off-by: David S. Miller <davem@davemloft.net>
With the devices added to the tables, the probe will recognize the
switch. This however is not sufficient to make it work properly, other
changes are needed because of incompatibilities.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Again a set of smaller fixes across several platforms (OMAP, Marvell,
Allwinner, i.MX, etc).
A handful of typo fixes and smaller missing contents from device trees,
with some tweaks to OMAP mach files to deal with CPU feature print
misformatting, potential NULL ptr dereference and one setup issue
with UARTs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJYMQiXAAoJEIwa5zzehBx3mkEP/jX7eTKIlancJKrW12IJWVU3
da3RuLxTE8IVpnQcHRjn9oi1Av6YNAWscLo7hrOmv1RGPMBKqGtPZERF11LdVc6E
UseMY9nqJH+9544+svCFNEvaLuug10VPOherw5v1H3hwPi5fz2aZlsGcEXC0ebDl
StWcH7App0tbBB/cnJJEvw7yLtq1nZkyXiVO2xupHW6wewRvqMe27vVO6AO4NdUK
bBEJf3C+TVh+n6cQ0DxvjVXoA3Uzk80cbivExenhpCYF2N5pLnV8fK2sttNGZa15
vgin/RyusUN0w9YIy3c/gdjqvp5B1Juna5D2VgV41MqFkBuXfqcZxLi3O4TtIzFY
uVNuOdXdAsaVuSZC9fNzdwIRgpfcYbV5WySnWBQBljaLk+Qac3QmDj2GVM5LbNCo
llxhIDOi8W91RqQJrIWVuKGxeJetB4Khpie68gu6lDYytY5Y1jCHpzhJAGJL69iJ
90rf/TswF4NYZ6nPMc4YF+PC0yrFXW475EROKpF9S9T6CgWSs9ogSp5a/tDVk4Mu
r/XeQ9pfzPA/3elGYY52CanWySHXpbUdJZAzsPOIrf8tIugBDhtUEnXVnMpU6RiI
HV3X7Y8Zrlzx+T1Gp/10VY02qfUOKAjbKUGWxNvB561QQXtBxDYlnhjlKXSUSdmE
UH62ODrQD9kMFbgk2Z1S
=jSKg
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Again a set of smaller fixes across several platforms (OMAP, Marvell,
Allwinner, i.MX, etc).
A handful of typo fixes and smaller missing contents from device
trees, with some tweaks to OMAP mach files to deal with CPU feature
print misformatting, potential NULL ptr dereference and one setup
issue with UARTs"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ipmi/bt-bmc: change compatible node to 'aspeed, ast2400-ibt-bmc'
ARM: dts: STiH410-b2260: Fix typo in spi0 chipselect definition
ARM: dts: omap5: board-common: fix wrong SMPS6 (VDD-DDR3) voltage
ARM: omap3: Add missing memory node in SOM-LV
arm64: dts: marvell: add unique identifiers for Armada A8k SPI controllers
arm64: dts: marvell: fix clocksource for CP110 slave SPI0
arm64: dts: marvell: Fix typo in label name on Armada 37xx
ASoC: omap-abe-twl6040: fix typo in bindings documentation
dts: omap5: board-common: enable twl6040 headset jack detection
dts: omap5: board-common: add phandle to reference Palmas gpadc
ARM: OMAP2+: avoid NULL pointer dereference
ARM: OMAP2+: PRM: initialize en_uart4_mask and grpsel_uart4_mask
ARM: dts: omap3: Fix memory node in Torpedo board
ARM: AM43XX: Select OMAP_INTERCONNECT in Kconfig
ARM: OMAP3: Fix formatting of features printed
ARM: dts: imx53-qsb: Fix regulator constraints
ARM: dts: sun8i: fix the pinmux for UART1
Pull i2c fixes from Wolfram Sang:
"Some I2C driver bugfixes (and one documentation fix)"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: i2c-mux-pca954x: fix deselect enabling for device-tree
i2c: digicolor: use clk_disable_unprepare instead of clk_unprepare
i2c: mux: fix up dependencies
i2c: Documentation: i2c-topology: fix minor whitespace nit
i2c: mux: demux-pinctrl: make drivers with no pinctrl work again
ARM:
- Fix handling of the 32bit cycle counter
- Fix cycle counter filtering
x86:
- Fix a race leading to double unregistering of user notifiers
- Amend oversight in kvm_arch_set_irq that turned Hyper-V code dead
- Use SRCU around kvm_lapic_set_vapic_addr
- Avoid recursive flushing of asynchronous page faults
- Do not rely on deferred update in KVM_GET_CLOCK, which fixes #GP
- Let userspace know that KVM_GET_CLOCK is useful with master clock;
4.9 changed the return value to better match the guest clock, but
didn't provide means to let guests take advantage of it
-----BEGIN PGP SIGNATURE-----
iQEcBAABCAAGBQJYMKbdAAoJEED/6hsPKofoPcEIAJF7hsuO3B2dMfUTz1EK+4IH
B7JXr9mlAAEG61y82EY06Es+3gt69XBiE5iKBpxlL6jIJJiUOd+oOdygV0hv4D0K
G6A03DsCWX16yJKjS7oGq4WOAiDGOpk7SU5YYlFZGqCzhaqScY2ecQFKEUYayJtt
nXG+i22eFKccrD8wlkm3ZYEjl1Hif7bUmHfxL/CBec1cDNxOys1dB24VsZl90n89
7pMUtzOTskUXjbNX+cKmFtR18/XUdlucnn0w9AApf3M8GnmUxIjIaeFSLbzuNz84
U2o3LdxrYysSKSsc7VleHtWVfCbPbC62vpUI51XdNw0u7BHlKkVdvBfJEUmSpkw=
=Crjd
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Radim Krčmář:
"ARM:
- Fix handling of the 32bit cycle counter
- Fix cycle counter filtering
x86:
- Fix a race leading to double unregistering of user notifiers
- Amend oversight in kvm_arch_set_irq that turned Hyper-V code dead
- Use SRCU around kvm_lapic_set_vapic_addr
- Avoid recursive flushing of asynchronous page faults
- Do not rely on deferred update in KVM_GET_CLOCK, which fixes #GP
- Let userspace know that KVM_GET_CLOCK is useful with master clock;
4.9 changed the return value to better match the guest clock, but
didn't provide means to let guests take advantage of it"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
kvm: x86: merge kvm_arch_set_irq and kvm_arch_set_irq_inatomic
KVM: x86: fix missed SRCU usage in kvm_lapic_set_vapic_addr
KVM: async_pf: avoid recursive flushing of work items
kvm: kvmclock: let KVM_GET_CLOCK return whether the master clock is in use
KVM: Disable irq while unregistering user notifier
KVM: x86: do not go through vcpu in __get_kvmclock_ns
KVM: arm64: Fix the issues when guest PMCCFILTR is configured
arm64: KVM: pmu: Fix AArch32 cycle counter access
Userspace can read the exact value of kvmclock by reading the TSC
and fetching the timekeeping parameters out of guest memory. This
however is brittle and not necessary anymore with KVM 4.11. Provide
a mechanism that lets userspace know if the new KVM_GET_CLOCK
semantics are in effect, and---since we are at it---if the clock
is stable across all VCPUs.
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
This patch derives device tree node from pcie bus layer framework.
Device tree bindings file has been renamed(marvell-sd8xxx.txt ->
marvell-8xxx.txt) to accommodate PCIe changes.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Rajat Jain <rajatja@google.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
features printed, all these are quite trivial and tiny. The omap5 jack
detection and gpadc patches are not strictly fixes, but I wanted to get
binding document typo fixed before it pops up on other boards. The
gpadc one liner was in the same series and I applied and pushed it out
already before noticing it could have waited. The list of changes is:
- Fix omap3 SoC features printed
- Make sure OMAP_INTERCONNECT is selected for am43xx only configurations
- Add missing memory node for torpedo
- Initialize uart4_mask properly to avoid writing garbage to PRM registers
- Fix NULL pointer dereference for omap4 volt_data
- Add alias for omap5 gpadc needed by iio drivers
- Enable omap5 jack headset jack detection and fix it's binding typo
- Add missing memory node for logicpd-som-lv
- Fix wrong SMPS6 voltage for VDD-DDR3 for omap5
-----BEGIN PGP SIGNATURE-----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=LgIW
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.9/fixes-for-rc-cycle' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps for v4.9-rc cycle. Except for the omap3 fix for the SoC
features printed, all these are quite trivial and tiny. The omap5 jack
detection and gpadc patches are not strictly fixes, but I wanted to get
binding document typo fixed before it pops up on other boards. The
gpadc one liner was in the same series and I applied and pushed it out
already before noticing it could have waited. The list of changes is:
- Fix omap3 SoC features printed
- Make sure OMAP_INTERCONNECT is selected for am43xx only configurations
- Add missing memory node for torpedo
- Initialize uart4_mask properly to avoid writing garbage to PRM registers
- Fix NULL pointer dereference for omap4 volt_data
- Add alias for omap5 gpadc needed by iio drivers
- Enable omap5 jack headset jack detection and fix it's binding typo
- Add missing memory node for logicpd-som-lv
- Fix wrong SMPS6 voltage for VDD-DDR3 for omap5
* tag 'omap-for-v4.9/fixes-for-rc-cycle' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap5: board-common: fix wrong SMPS6 (VDD-DDR3) voltage
ARM: omap3: Add missing memory node in SOM-LV
ASoC: omap-abe-twl6040: fix typo in bindings documentation
dts: omap5: board-common: enable twl6040 headset jack detection
dts: omap5: board-common: add phandle to reference Palmas gpadc
ARM: OMAP2+: avoid NULL pointer dereference
ARM: OMAP2+: PRM: initialize en_uart4_mask and grpsel_uart4_mask
ARM: dts: omap3: Fix memory node in Torpedo board
ARM: AM43XX: Select OMAP_INTERCONNECT in Kconfig
ARM: OMAP3: Fix formatting of features printed
Signed-off-by: Olof Johansson <olof@lixom.net>
The Aspeed SoCs have two BT interfaces : one is IPMI compliant and the
other is H8S/2168 compliant.
The current ipmi/bt-bmc driver implements the IPMI version and we
should reflect its nature in the compatible node name using
'aspeed,ast2400-ibt-bmc' instead of 'aspeed,ast2400-bt-bmc'. The
latter should be used for a H8S interface driver if it is implemented
one day.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Introduce managed counterparts for alloc_percpu() and free_percpu().
Add devm_alloc_percpu() and devm_free_percpu() into the managed
interfaces list.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add documentation how devicetree can be used to configure ath9k based
devices.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Pull networking fixes from David Miller:
1) Fix off by one wrt. indexing when dumping /proc/net/route entries,
from Alexander Duyck.
2) Fix lockdep splats in iwlwifi, from Johannes Berg.
3) Cure panic when inserting certain netfilter rules when NFT_SET_HASH
is disabled, from Liping Zhang.
4) Memory leak when nft_expr_clone() fails, also from Liping Zhang.
5) Disable UFO when path will apply IPSEC tranformations, from Jakub
Sitnicki.
6) Don't bogusly double cwnd in dctcp module, from Florian Westphal.
7) skb_checksum_help() should never actually use the value "0" for the
resulting checksum, that has a special meaning, use CSUM_MANGLED_0
instead. From Eric Dumazet.
8) Per-tx/rx queue statistic strings are wrong in qed driver, fix from
Yuval MIntz.
9) Fix SCTP reference counting of associations and transports in
sctp_diag. From Xin Long.
10) When we hit ip6tunnel_xmit() we could have come from an ipv4 path in
a previous layer or similar, so explicitly clear the ipv6 control
block in the skb. From Eli Cooper.
11) Fix bogus sleeping inside of inet_wait_for_connect(), from WANG
Cong.
12) Correct deivce ID of T6 adapter in cxgb4 driver, from Hariprasad
Shenai.
13) Fix potential access past the end of the skb page frag array in
tcp_sendmsg(). From Eric Dumazet.
14) 'skb' can legitimately be NULL in inet{,6}_exact_dif_match(). Fix
from David Ahern.
15) Don't return an error in tcp_sendmsg() if we wronte any bytes
successfully, from Eric Dumazet.
16) Extraneous unlocks in netlink_diag_dump(), we removed the locking
but forgot to purge these unlock calls. From Eric Dumazet.
17) Fix memory leak in error path of __genl_register_family(). We leak
the attrbuf, from WANG Cong.
18) cgroupstats netlink policy table is mis-sized, from WANG Cong.
19) Several XDP bug fixes in mlx5, from Saeed Mahameed.
20) Fix several device refcount leaks in network drivers, from Johan
Hovold.
21) icmp6_send() should use skb dst device not skb->dev to determine L3
routing domain. From David Ahern.
22) ip_vs_genl_family sets maxattr incorrectly, from WANG Cong.
23) We leak new macvlan port in some cases of maclan_common_netlink()
errors. Fix from Gao Feng.
24) Similar to the icmp6_send() fix, icmp_route_lookup() should
determine L3 routing domain using skb_dst(skb)->dev not skb->dev.
Also from David Ahern.
25) Several fixes for route offloading and FIB notification handling in
mlxsw driver, from Jiri Pirko.
26) Properly cap __skb_flow_dissect()'s return value, from Eric Dumazet.
27) Fix long standing regression in ipv4 redirect handling, wrt.
validating the new neighbour's reachability. From Stephen Suryaputra
Lin.
28) If sk_filter() trims the packet excessively, handle it reasonably in
tcp input instead of exploding. From Eric Dumazet.
29) Fix handling of napi hash state when copying channels in sfc driver,
from Bert Kenward.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (121 commits)
mlxsw: spectrum_router: Flush FIB tables during fini
net: stmmac: Fix lack of link transition for fixed PHYs
sctp: change sk state only when it has assocs in sctp_shutdown
bnx2: Wait for in-flight DMA to complete at probe stage
Revert "bnx2: Reset device during driver initialization"
ps3_gelic: fix spelling mistake in debug message
net: ethernet: ixp4xx_eth: fix spelling mistake in debug message
ibmvnic: Fix size of debugfs name buffer
ibmvnic: Unmap ibmvnic_statistics structure
sfc: clear napi_hash state when copying channels
mlxsw: spectrum_router: Correctly dump neighbour activity
mlxsw: spectrum: Fix refcount bug on span entries
bnxt_en: Fix VF virtual link state.
bnxt_en: Fix ring arithmetic in bnxt_setup_tc().
Revert "include/uapi/linux/atm_zatm.h: include linux/time.h"
tcp: take care of truncations done by sk_filter()
ipv4: use new_gw for redirect neigh lookup
r8152: Fix error path in open function
net: bpqether.h: remove if_ether.h guard
net: __skb_flow_dissect() must cap its return value
...
Minor doc fix, a DMI match for ideapad and a fix to toshiba-wmi to avoid loading
on non-toshiba systems.
Documentation/ABI:
- ibm_rtl: The "What:" fields are incomplete
toshiba-wmi:
- Fix loading the driver on non Toshiba laptops
ideapad-laptop:
- Add another DMI entry for Yoga 900
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYJSzXAAoJEKbMaAwKp364Df0IAKOMnIMZ35K4uKCemZ7dVEtW
VvMgch2RZwEa+Oy8Og0o6WGYyurOR66w4oJqGlc9BYPaQo/akiKU0xLcQ2fqndsc
PnkberSaqER5/9COnSXLCWH9WsCW3rvdGHLg7ZicUiO+b6n/90hM4MRWL6j3QZCl
FYgMMEKSpPz7juZAdPIvfE4Mr157aESwmcHkihi7F4Ui6k2jln49R+zQoM6h9D/u
nH/pamxkfO/cJGQ3wcLVPhu6EL9wLqWU/+1/7FILYpoWkbiaJH3TtElQ3OU2yXq+
PmMcS8nI7Uv2Jrx66MfMx0fkCdA0lx5SlXsEmlwGtwk8A4qJq2AwTRvz5slHHTA=
=Upe0
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v4.9-3' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull x86 platform driver fixes from Darren Hart:
"Minor doc fix, a DMI match for ideapad and a fix to toshiba-wmi to
avoid loading on non-toshiba systems.
Documentation/ABI:
- ibm_rtl: The "What:" fields are incomplete
toshiba-wmi:
- Fix loading the driver on non Toshiba laptops
ideapad-laptop:
- Add another DMI entry for Yoga 900"
* tag 'platform-drivers-x86-v4.9-3' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
Documentation/ABI: ibm_rtl: The "What:" fields are incomplete
toshiba-wmi: Fix loading the driver on non Toshiba laptops
ideapad-laptop: Add another DMI entry for Yoga 900
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=5c2j
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.9-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
- Update MAINTAINERS for Intel VMD driver filename
- Update Rockchip rk3399 host bridge driver DTS and resets
- Fix ROM shadow problem that made some video device initialization
fail
* tag 'pci-v4.9-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: VMD: Update filename to reflect move
arm64: dts: rockchip: add three new resets for rk3399 PCIe controller
PCI: rockchip: Add three new resets as required properties
PCI: Don't attempt to claim shadow copies of ROM
- Fix mmc card initialization for hosts not supporting HW busy detection
- Fix mmc_test for sending commands during non-blocking write
MMC host:
- mxs: Avoid using an uninitialized
- sdhci: Restore enhanced strobe setting during runtime resume
- sdhci: Fix a couple of reset related issues
- dw_mmc: Fix a reset controller issue
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=mnjf
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"MMC core:
- Fix mmc card initialization for hosts not supporting HW busy
detection
- Fix mmc_test for sending commands during non-blocking write
MMC host:
- mxs: Avoid using an uninitialized
- sdhci: Restore enhanced strobe setting during runtime resume
- sdhci: Fix a couple of reset related issues
- dw_mmc: Fix a reset controller issue"
* tag 'mmc-v4.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: mxs: Initialize the spinlock prior to using it
mmc: mmc: Use 500ms as the default generic CMD6 timeout
mmc: mmc_test: Fix "Commands during non-blocking write" tests
mmc: sdhci: Fix missing enhanced strobe setting during runtime resume
mmc: sdhci: Reset cmd and data circuits after tuning failure
mmc: sdhci: Fix unexpected data interrupt handling
mmc: sdhci: Fix CMD line reset interfering with ongoing data transfer
mmc: dw_mmc: add the "reset" as name of reset controller
Documentation: synopsys-dw-mshc: add binding for reset-names
- Fix a host of runtime problems with the Intel
Cherryview driver: suspend/resume needs to be
marshalled properly, and strange effects from BIOS
interaction during suspend/resume need to be
dealt with.
- A single bit was being set wrong in the Aspeed
driver.
- Fix an iProc probe ordering fallout resulting from
v4.9 refactorings for bus population.
- Do not specify a default trigger in the ST Micro
cascaded GPIO IRQ controller: the kernel will moan.
- Make IRQs optional altogether on the STM32 driver,
it turns out not all systems have them or want them.
- Fix a re-probe bug in the i.MX driver, it will
eventually crash if probed repeatedly, not good.
-----BEGIN PGP SIGNATURE-----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=ENR8
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"All is about drivers, no core business going on.
- Fix a host of runtime problems with the Intel Cherryview driver:
suspend/resume needs to be marshalled properly, and strange effects
from BIOS interaction during suspend/resume need to be dealt with.
- A single bit was being set wrong in the Aspeed driver.
- Fix an iProc probe ordering fallout resulting from v4.9
refactorings for bus population.
- Do not specify a default trigger in the ST Micro cascaded GPIO IRQ
controller: the kernel will moan.
- Make IRQs optional altogether on the STM32 driver, it turns out not
all systems have them or want them.
- Fix a re-probe bug in the i.MX driver, it will eventually crash if
probed repeatedly, not good"
* tag 'pinctrl-v4.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl-aspeed-g5: Never set SCU90[6]
pinctrl: cherryview: Prevent possible interrupt storm on resume
pinctrl: cherryview: Serialize register access in suspend/resume
pinctrl: imx: reset group index on probe
pinctrl: stm32: move gpio irqs binding to optional
pinctrl: stm32: remove dependency with interrupt controller
pinctrl: st: don't specify default interrupt trigger
pinctrl: iproc: Fix iProc and NSP GPIO support
Pull VFS fixes from Al Viro:
"Christoph's and Jan's aio fixes, fixup for generic_file_splice_read
(removal of pointless detritus that actually breaks it when used for
gfs2 ->splice_read()) and fixup for generic_file_read_iter()
interaction with ITER_PIPE destinations."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
splice: remove detritus from generic_file_splice_read()
mm/filemap: don't allow partially uptodate page for pipes
aio: fix freeze protection of aio writes
fs: remove aio_run_iocb
fs: remove the never implemented aio_fsync file operation
aio: hold an extra file reference over AIO read/write operations
Woojung.Huh@microchip.com