I use 2.6.15.6 Linux kernel and found some problems. I have about 100
Linux boxes (all with the same (binary the same) kernel). Last time I have
upgraded all those boxes from 2.4.32 to 2.6.15.6 (first 2.6.15.1, next .2,
.4 and .6) and I have found some problems on VIA based PC's. Probably the
reason of this is that some VIA chipsets are unrecognized by IRQ router.
In line 586 there is: /* FIXME: add new ones for 8233/5 */
There were only a few of chipsets ID's there, some of my VIA chipsets were
not present and kernel used default IRQ router.
I have added three entries, so that the code looks like:
case PCI_DEVICE_ID_VIA_82C596:
case PCI_DEVICE_ID_VIA_82C686:
case PCI_DEVICE_ID_VIA_8231:
case PCI_DEVICE_ID_VIA_8233A:
case PCI_DEVICE_ID_VIA_8235:
case PCI_DEVICE_ID_VIA_8237:
case PCI_DEVICE_ID_VIA_8237_SATA:
/* FIXME: add new ones for 8233/5 */
r->name = "VIA";
r->get = pirq_via_get;
r->set = pirq_via_set;
return 1;
}
The kernel goes fine but I haven't testes it for weeks, I'm just a moment
after reboot :)
One thing is different (better?):
Using previus kernel I had:
PCI: Via IRQ fixup for 0000:00:0f.1, from 255 to 0
now I have:
PCI: Via IRQ fixup for 0000:00:0f.1, from 255 to 11
Maybe it is good idea to add there some more VIA chipsets?
The ones I have added seem to be OK.
From: Grzegorz Janoszka <Grzegorz@Janoszka.pl>
Acked-by: Martin Mares <mj@ucw.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The init function for the RPA PCI Hotplug driver returns -ENODEV in the
case that no hotplug-capable slots are detected in the system. This is
bad, since hot-capable slots can be added after boot to a purely virtual
POWER partition. This is also bad because DLPAR I/O operations depend
on the rpaphp module.
Change the rpaphp init module to return success for the case of
partitions that own no hotplug-capable slots at boot. Such slots can be
dynamically added after boot.
Signed-off-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sparse warns about casting to a __bitwise type. However, it's correct
to do when defining the enum for pci_bus_flags_t, so add a __force to
quiet the warnings. This will fix getting
include/linux/pci.h💯26: warning: cast to restricted type
from sparse all over the build.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The naming of the constant defined for PCI ID 1022:7450 does not seem
to match the information at http://pciids.sourceforge.net/:
http://pci-ids.ucw.cz/iii/?i=1022
There 1022:7450 is listed as "AMD-8131 PCI-X Bridge" while 1022:7451
is listed as "AMD-8131 PCI-X IOAPIC". Yet, the current definition for
0x7450 is PCI_DEVICE_ID_AMD_8131_APIC. It seems to me like that name
should map to 0x7451, while a name like PCI_DEVICE_ID_AMD_8131_BRIDGE
should map to 0x7450.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For easily getting fairly good accessibility, the TTY cursor should
always be left at the focus location. This patch fixes the checklist by
just having the list refreshed after the dialog box (hence the cursor
position remains in the list).
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/mszeredi/fuse:
[fuse] Direct I/O should not use fuse_reset_request
[fuse] Don't init request twice
[fuse] Fix accounting the number of waiting requests
[fuse] fix deadlock between fuse_put_super() and request_end()
* 'tee' of git://brick.kernel.dk/data/git/linux-2.6-block:
[PATCH] splice: add support for sys_tee()
[PATCH] splice: pass offset around for ->splice_read() and ->splice_write()
This reverts most of commit 30e0fca6c1.
It broke the case of non-leader MT exec when ptraced.
I think the bug it was intended to fix was already addressed by commit
788e05a67c.
Signed-off-by: Roland McGrath <roland@redhat.com>
Acked-by: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is two distinct changes.
- Not changing our real parents.
- Not changing our ptrace parents.
Not changing our real parents is trivially correct because both tasks
have the same real parents as they are part of a thread group. Now that
we demote the leader to a thread there is no longer any reason to change
it's parentage.
Not changing our ptrace parents is a user visible change if someone
looks hard enough. I don't think user space applications will care or
even notice.
In the practical and I think common case a debugger will have attached
to all of the threads using the same ptrace flags. From my quick skim
of strace and gdb that appears to be the case. Which if true means
debuggers will not notice a change.
Before this point we have already generated a ptrace event in do_exit
that reports the leaders pid has died so de_thread is visible to a
debugger. Which means attempting to hide this case by copying flags
around appears excessive.
By not doing anything it avoids all of the weird locking issues between
de_thread and ptrace attach, and removes one case from consideration for
fixing the ptrace locking.
This only addresses Oleg's first concern with ptrace_attach, that of the
problems caused by reparenting. Oleg's second concern is essentially a
race between ptrace_attach and release_task that causes an oops when we
get to force_sig_specific. There is nothing special about de_thread
with respect to that race.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] Make show_mem() skip holes in a pgdat
[IA64] ia64_wait_for_slaves() incorrectly reports MCA
This patch modifies ia64's show_mem() to walk the vmem_map page tables and
rapidly skip forward across regions where the page tables are missing.
This prevents the pfn_valid() check from causing numerous unnecessary
page faults.
Without this patch on a 512 node 512 cpu system where every node has four
memory holes, the show_mem() call takes 1 hour 18 minutes. With this
patch, it takes less than 3 seconds.
Signed-off-by: Robin Holt <holt@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
ia64_wait_for_slaves() was changed in 2.6.17-rc1 to report the slave
state. It incorrectly assumes that all slaves are for MCA, but
ia64_wait_for_slaves() is also called from the INIT monarch handler.
The existing message is very misleading, so correct it.
Signed-off-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
By calling send_sig do_SAK is recursively taking the
tasklist_lock, which is silly.
In addition I just audited the kernel and this was the only
place where tasklist_lock is taken inside of task_lock.
So this one line change is a general worthwhile cleanup and
it increases our options on how to fix the ptrace_attach races.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
[PATCH] Use pci_set_consistent_dma_mask in ixgb driver
[PATCH] sky2: bad memory reference on dual port cards
[PATCH] mv643xx_eth: Fix tx_timeout to only conditionally wake tx queue
[PATCH] mv643xx_eth: Always free completed tx descs on tx interrupt
[PATCH] net drivers: fix section attributes for gcc
[PATCH] remove drivers/net/hydra.h
[PATCH] drivers/net/via-rhine.c: make a function static
[netdrvr b44] trim trailing whitespace
[PATCH] b44: increase version to 1.00
[PATCH] b44: disable default tx pause
[PATCH] via-rhine: execute bounce buffers code on Rhine-I only
[PATCH] network: axnet_cs.c: add missing 'PRIV' in ei_rx_overrun
[PATCH] dlink pci cards using wrong driver
The ixgb driver is using pci_alloc_consistent, thus is should also use
pci_set_consistent_dma_mask. This allows the driver to work on SGI
systems.
In case of an error during probing it should also disable the device again.
Signed-off-by: Andreas Schwab <schwab@suse.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Sky2 driver will oops referencing bad memory if used on
a dual port card. The problem is accessing past end of
MIB counter space.
Applies for both 2.6.17 and 2.6.16 (with fuzz)
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
After resetting the hardware on a tx_timeout, call netif_wake_queue()
only if we have free tx descriptors.
Also, attempt to recover if mv643xx_eth_start_xmit() is called when
there are fewer free tx descriptors than expected.
The BUG_ON() call we are replacing was hit on a tx_timeout that
called netif_wake_queue(), indirectly via netif_device_attach(),
even though we did not have enough free tx descriptors.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix the tx interrupt handler to free completed tx descriptors even
when NAPI is enabled. Otherwise, the tx queue would fill up resulting
in poor performance and "NETDEV WATCHDOG: <iface>: transmit timed out"
messages.
Signed-off-by: Brent Cook <bcook@bpointsys.com>
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If CONFIG_HOTPLUG=n, gcc doesn't like some __initdata to be const (rodata)
and other __initdata not const, so make the non-const __initdata const.
gcc errors:
drivers/net/bnx2.c:66: error: version causes a section type conflict
drivers/net/starfire.c:338: error: version causes a section type conflict
drivers/net/typhoon.c:137: error: version causes a section type conflict
drivers/net/natsemi.c:241: error: version causes a section type conflict
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove drivers/net/hydra.h which is both unused and covered by a 4 clause
BSD licence (not by the UCB).
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-By: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Roger Luethi <rl@hellgate.ch>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Currently it crashes when trying to dump the registers. This is an obvious
one-liner fix I suppose.
Signed-off-by: Dan Aloni <da-x@monatomic.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Disable default tx pause frame support.
The b44 controller has a bug that generates excessive tx pause
frames.
Signed-off-by: Gary Zambrano <zambrano@broadcom.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes the problem of some Dlink cards picking the wrong
driver. It looks like these cards use Yukon 1 chipset, not Yukon 2.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The driver allocates SRQ WQEs size with a power of 2 size both for
Tavor and for memfree. For Tavor, however, the hardware only requires
the WQE size to be a multiple of 16, not a power of 2, and the max
number of scatter-gather allowed is reported accordingly by the
firmware (and this is the value currently returned by
ib_query_device() and ibv_query_device()).
If the max number of scatter/gather entries reported by the FW is used
when creating an SRQ, the creation will fail for Tavor, since the
required WQE size will be increased to the next power of 2, which
turns out to be larger than the device permitted max WQE size (which
is not a power of 2).
This patch reduces the reported SRQ max wqe size so that it can be used
successfully in creating an SRQ on Tavor HCAs.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[ISDN]: Static overruns in drivers/isdn/i4l/isdn_ppp.c
[WAN]: Remove broken and unmaintained Sangoma drivers.
[BRIDGE] ebtables: fix allocation in net/bridge/netfilter/ebtables.c
[DCCP]: Fix leak in net/dccp/ipv4.c
[BRIDGE]: receive link-local on disabled ports.
[IPv6] reassembly: Always compute hash under the fragment lock.
Unregister the platform device again if the probe was unsuccessful.
This restores the behaviour of not loading the driver on probe() failure.
Signed-off-by: Rene Herman <rene.herman@keyaccess.nl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Continue with the next one on error from device registration.
This would seem the correct thing to do, even if it's not the probe()
error that we're getting.
Signed-off-by: Rene Herman <rene.herman@keyaccess.nl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: PCM Midlevel
This patch makes the needlessly global snd_pcm_format_name() static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: au88x0 driver
since idx is used as an index for vortex_pcm_prettyname[VORTEX_PCM_LAST],
it should not be equal to VORTEX_PCM_LAST. This fixes coverity bug id #572
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: au88x0 driver
Removed all use of __devinit/__devexit and init.h from headers. Any
attributes given in the prototype but not in the function definition have
been moved to the definition.
An exception is vortex_eq_free: I removed the __devexit attribute because
vortex_eq_free is called from vortex_core_shutdown, and
vortex_core_shutdown may be called from __devinit snd_vortex_create.
Compile tested with allyesconfig and allmodconfig.
Signed-off-by: Dale Sedivec <dale@codefu.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: HDA Codec driver
This patch adds the entry for the 5-stack pin-config for the STAC
chip on the Intel D945Pvs board with subdevice id 0x0707.
With this patch against 1.0.11rc4 in the linux kernel 2.6.17-rc1, I'm
able to successfully output over the optical port and analog ports.
Signed-off-by: Ashley Clark <aclark@ghoti.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: HDA Codec driver
This adds the support for HP Compaq Presario B2800 laptop with AD1986A codec.
Signed-off-by: Coywolf Qi Hunt <qiyong@freeforge.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: ALSA<-OSS emulation
Fix Oops due to a typo in snd_pcm_oss.c.
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Coverity found some static overruns in isdn_ppp.c (bug id #519) At several
places slot is compared <0 and > ISDN_MAX_CHANNELS and then used to index
ippp_table[ISDN_MAX_CHANNELS] A value of slot = ISDN_MAX_CHANNELS would run
over the end of the array.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The in-kernel Sangoma drivers are both not compiling and marked as BROKEN
since at least kernel 2.6.0.
Sangoma offers out-of-tree drivers, and David Mandelstam told me Sangoma
does no longer maintain the in-kernel drivers and prefers to provide them
as a separate installation package.
This patch therefore removes these drivers.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate an array of 'struct ebt_chainstack *', the current code allocates
array of 'struct ebt_chainstack'.
akpm: converted to use the
foo = alloc(sizeof(*foo))
form. Which would have prevented this from happening in the first place.
akpm: also removed unneeded typecast.
akpm: what on earth is this code doing anyway? cpu_possible_map can be
sparse..
Signed-off-by: Jayachandran C. <c.jayachandran@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Grzegorz Janoszka