We need to quiesce interrupts in the poll_get_char routine, otherwise,
if used with KGDB NMI debugger, we'll keep reentering the NMI.
Quiescing interrupts is pretty straightforward, except for TXIM
interrupt. The interrupt has "ready to transmit" meaning, so it's
almost always raised, and the only way to silence it is to mask it. But
that's OK, ops->start_tx will unmask it.
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The callback is used to initialize the hardware, nothing else should be
done, i.e. we should not request interrupts (but we can and do unmask
some of them, as they might be useful for NMI entry).
As a side-effect, the patch also fixes a division by zero[1] when booting
with kgdboc options specified (e.g. kgdboc=ttyAMA0,115200n8). The issue
happens because serial core calls set_termios callback, but the driver
doesn't know clock frequency, and thus cannot calculate proper baud rate
values.
[1]
WARNING: at drivers/tty/serial/serial_core.c:400 uart_get_baud_rate+0xe8/0x14c()
Modules linked in:
[<c0018e50>] (unwind_backtrace+0x0/0xf0) from [<c0020ae8>] (warn_slowpath_common+0x4c/0x64)
[<c0020ae8>] (warn_slowpath_common+0x4c/0x64) from [<c0020b1c>] (warn_slowpath_null+0x1c/0x24)
[<c0020b1c>] (warn_slowpath_null+0x1c/0x24) from [<c0185ed8>] (uart_get_baud_rate+0xe8/0x14c)
[<c0185ed8>] (uart_get_baud_rate+0xe8/0x14c) from [<c0187078>] (pl011_set_termios+0x48/0x278)
[<c0187078>] (pl011_set_termios+0x48/0x278) from [<c01850b0>] (uart_set_options+0xe8/0x114)
[<c01850b0>] (uart_set_options+0xe8/0x114) from [<c0185de4>] (uart_poll_init+0xd4/0xe0)
[<c0185de4>] (uart_poll_init+0xd4/0xe0) from [<c016da8c>] (tty_find_polling_driver+0x100/0x17c)
[<c016da8c>] (tty_find_polling_driver+0x100/0x17c) from [<c0188538>] (configure_kgdboc+0xc8/0x1b8)
[<c0188538>] (configure_kgdboc+0xc8/0x1b8) from [<c00088a4>] (do_one_initcall+0x30/0x168)
[<c00088a4>] (do_one_initcall+0x30/0x168) from [<c033784c>] (do_basic_setup+0x94/0xc8)
[<c033784c>] (do_basic_setup+0x94/0xc8) from [<c03378e0>] (kernel_init+0x60/0xf4)
[<c03378e0>] (kernel_init+0x60/0xf4) from [<c00144a0>] (kernel_thread_exit+0x0/0x8)
---[ end trace 7d41c9186f342c40 ]---
Division by zero in kernel.
[<c0018e50>] (unwind_backtrace+0x0/0xf0) from [<c014546c>] (Ldiv0+0x8/0x10)
[<c014546c>] (Ldiv0+0x8/0x10) from [<c0187098>] (pl011_set_termios+0x68/0x278)
[<c0187098>] (pl011_set_termios+0x68/0x278) from [<c01850b0>] (uart_set_options+0xe8/0x114)
[<c01850b0>] (uart_set_options+0xe8/0x114) from [<c0185de4>] (uart_poll_init+0xd4/0xe0)
[<c0185de4>] (uart_poll_init+0xd4/0xe0) from [<c016da8c>] (tty_find_polling_driver+0x100/0x17c)
[<c016da8c>] (tty_find_polling_driver+0x100/0x17c) from [<c0188538>] (configure_kgdboc+0xc8/0x1b8)
[<c0188538>] (configure_kgdboc+0xc8/0x1b8) from [<c00088a4>] (do_one_initcall+0x30/0x168)
[<c00088a4>] (do_one_initcall+0x30/0x168) from [<c033784c>] (do_basic_setup+0x94/0xc8)
[<c033784c>] (do_basic_setup+0x94/0xc8) from [<c03378e0>] (kernel_init+0x60/0xf4)
[<c03378e0>] (kernel_init+0x60/0xf4) from [<c00144a0>] (kernel_thread_exit+0x0/0x8)
Division by zero in kernel.
[<c0018e50>] (unwind_backtrace+0x0/0xf0) from [<c014546c>] (Ldiv0+0x8/0x10)
[<c014546c>] (Ldiv0+0x8/0x10) from [<c0183a98>] (uart_update_timeout+0x4c/0x5c)
[<c0183a98>] (uart_update_timeout+0x4c/0x5c) from [<c01870f8>] (pl011_set_termios+0xc8/0x278)
[<c01870f8>] (pl011_set_termios+0xc8/0x278) from [<c01850b0>] (uart_set_options+0xe8/0x114)
[<c01850b0>] (uart_set_options+0xe8/0x114) from [<c0185de4>] (uart_poll_init+0xd4/0xe0)
[<c0185de4>] (uart_poll_init+0xd4/0xe0) from [<c016da8c>] (tty_find_polling_driver+0x100/0x17c)
[<c016da8c>] (tty_find_polling_driver+0x100/0x17c) from [<c0188538>] (configure_kgdboc+0xc8/0x1b8)
[<c0188538>] (configure_kgdboc+0xc8/0x1b8) from [<c00088a4>] (do_one_initcall+0x30/0x168)
[<c00088a4>] (do_one_initcall+0x30/0x168) from [<c033784c>] (do_basic_setup+0x94/0xc8)
[<c033784c>] (do_basic_setup+0x94/0xc8) from [<c03378e0>] (kernel_init+0x60/0xf4)
[<c03378e0>] (kernel_init+0x60/0xf4) from [<c00144a0>] (kernel_thread_exit+0x0/0x8)
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This works around a few glitches in the ST version of the PL011
serial driver when using very high baud rates, as we do in the
Ux500: 3, 3.25, 4 and 4.05 Mbps.
Problem Observed/rootcause:
When using high baud-rates, and the baudrate*8 is getting close to
the provided clock frequency (so a division factor close to 1), when
using bursts of characters (so they are abutted), then it seems as if
there is not enough time to detect the beginning of the start-bit which
is a timing reference for the entire character, and thus the sampling
moment of character bits is moving towards the end of each bit, instead
of the middle.
Fix:
Increase slightly the RX baud rate of the UART above the theoretical
baudrate by 5%. This will definitely give more margin time to the
UART_RX to correctly sample the data at the middle of the bit period.
Also fix the ages old copy-paste error in the very stressed comment,
it's referencing the registers used in the PL010 driver rather than
the PL011 ones.
Signed-off-by: Guillaume Jaunet <guillaume.jaunet@stericsson.com>
Signed-off-by: Christophe Arnal <christophe.arnal@stericsson.com>
Signed-off-by: Matthias Locher <matthias.locher@stericsson.com>
Signed-off-by: Rajanikanth HV <rajanikanth.hv@stericsson.com>
Cc: stable <stable@vger.kernel.org>
Cc: Bibek Basu <bibek.basu@stericsson.com>
Cc: Par-Gunnar Hjalmdahl <par-gunnar.hjalmdahl@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bug flag .interrupt_may_hang is not used since commit
4fd0690bb0
"serial: pl011: implement workaround for CTS clear event issue"
so delete it.
Cc: Rajanikanth H.V <rajanikanth.hv@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the order of UART nodes is changed in the device tree, then tty dev
devices are attached to different serial ports causing the console to
be directed to a different physical serial port. The "serial" aliases
in the device tree should prevent this.
This patch ensures that the UART driver creates tty devices that
honour these aliases if a device tree is present.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Matthew Leach <matthew.leach@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clk_prepare_enable and clk_disable_unprepare combine clk_prepare and
clk_enable, and clk_disable and clk_unprepare. The9 make the code more
concise, and ensure that clk_unprepare is called when clk_enable fails.
A simplified version of the semantic patch that introduces calls to these
functions is as follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e;
@@
- clk_prepare(e);
- clk_enable(e);
+ clk_prepare_enable(e);
@@
expression e;
@@
- clk_disable(e);
- clk_unprepare(e);
+ clk_disable_unprepare(e);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This handles the merge issue in:
arch/um/drivers/line.c
arch/um/drivers/line.h
And resolves the duplicate patches that were in both trees do to the
tty-next branch not getting merged into 3.6-rc1.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is to pick up the serial port and tty changes in Linus's tree to allow
everyone to sync up.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PL011 driver has a number of symbols referring to "pl01x"
(probably once shared with the pl010 driver) and some even named
"pl010" (probably a pure copy-paste artifact). Lets name all
local static functions with the prefix pl011_* for clarity.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We had a boot regression in Ux500 in the merge window because
two orthogonal pin control schemes for the PL011 were merged
at the same time:
- One using the .init() and .exit() hooks into the platform
for Ux500 putting the pins into default vs sleep state
respectively as the port was started/stopped.
commit a09806607f
"ARM: ux500: switch to using pinctrl for uart0"
- One hogging the default setting at PL011 probe()
commit 258e055111
"serial: amba-pl011: adopt pinctrl support"
To get a solution that works for both let's scrap the stuff
in the platform callbacks, instead have the driver itself
select default and sleep states when the port is
started/stopped. Hopefully this works for all clients.
Platform callbacks are bad for device tree migration anyway,
so this rids us of another problem in Ux500.
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Reported-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the big TTY/serial driver pull request for the 3.5-rc1 merge window.
Nothing major in here, just lots of incremental changes from Alan and
Jiri reworking some tty core things to behave better and to get a more
solid grasp on some of the nasty tty locking issues.
There are a few tty and serial driver updates in here as well.
All of this has been in the linux-next releases for a while with no problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk+7rBoACgkQMUfUDdst+ykXsgCfeDKx6ZgLidYy3H40Y2Pt3XEO
TicAn1fcdGwOmMR/mowa+kTA68D/J6i2
=S7tG
-----END PGP SIGNATURE-----
Merge tag 'tty-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull TTY updates from Greg Kroah-Hartman:
"Here's the big TTY/serial driver pull request for the 3.5-rc1 merge
window.
Nothing major in here, just lots of incremental changes from Alan and
Jiri reworking some tty core things to behave better and to get a more
solid grasp on some of the nasty tty locking issues.
There are a few tty and serial driver updates in here as well.
All of this has been in the linux-next releases for a while with no
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'tty-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (115 commits)
serial: bfin_uart: Make MMR access compatible with 32 bits bf609 style controller.
serial: bfin_uart: RTS and CTS MMRs can be either 16-bit width or 32-bit width.
serial: bfin_uart: narrow the reboot condition in DMA tx interrupt
serial: bfin_uart: Adapt bf5xx serial driver to bf60x serial4 controller.
Revert "serial_core: Update buffer overrun statistics."
tty: hvc_xen: NULL dereference on allocation failure
tty: Fix LED error return
tty: Allow uart_register/unregister/register
tty: move global ldisc idle waitqueue to the individual ldisc
serial8250-em: Add DT support
serial8250-em: clk_get() IS_ERR() error handling fix
serial_core: Update buffer overrun statistics.
tty: drop the pty lock during hangup
cris: fix missing tty arg in wait_event_interruptible_tty call
tty/amiserial: Add missing argument for tty_unlock()
tty_lock: Localise the lock
pty: Lock the devpts bits privately
tty_lock: undo the old tty_lock use on the ctty
serial8250-em: Emma Mobile UART driver V2
Add missing call to uart_update_timeout()
...
Problem Observed:
- interrupt status is set by rising or falling edge on CTS line
- interrupt status is cleared on a .0. to .1. transition of the
interrupt-clear register bit 1.
- interrupt-clear register is reset by hardware once the interrupt
status is .0..
Remark: It seems not possible to read this register back by the
CPU though, but internally this register exists.
- when simultaneous set and reset event on the interrupt status
happens, then the set-event has priority and the status remains
.1.. As a result the interrupt-clear register is not reset to
.0., and no new .0. to .1. transition can be detected on it when
writing a .1. to it.
This implies race condition, the clear must be performed at least
one UARTCLK the riding edge of CTS RIS interrupt.
Fix:
Instead of resetting UART as done in commit
c16d51a32b
"amba pl011: workaround for uart registers lockup" do the
following:
write .0. and then .1. to the interrupt-clear register to make
sure that this transition is detected. According to the datasheet
writing a .0. does not have any effect, but actually it allows to
reset the internal interrupt-clear register.
Take into account:
The .0. needs to last at least for one clk_uart clock period
(~ 38 MHz, 26.08ns)
This way we can do away with the tasklet and keep only a tiny
fix triggered by the variant flag introduced in this patch.
Signed-off-by: Guillaume Jaunet <guillaume.jaunet@stericsson.com>
Signed-off-by: Christophe Arnal <christophe.arnal@stericsson.com>
Signed-off-by: Matthias Locher <Matthias.Locher@stericsson.com>
Signed-off-by: Rajanikanth H.V <rajanikanth.hv@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 360f748b204275229f8398cb2f9f53955db1503b
"serial: PL011: clear pending interrupts"
attempts to clear interrupts by writing to a
yet-unassigned memory address. This fixes the issue.
The breaking patch is marked for stable so should be
carried along with the other patch.
Cc: Shreshtha Kumar Sahu <shreshthakumar.sahu@stericsson.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: stable <stable@vger.kernel.org>
Cc: Nicolas Pitre <nico@fluxnic.net>
Reported-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull slave-dmaengine update from Vinod Koul:
"This includes the cookie cleanup by Russell, the addition of context
parameter for dmaengine APIs, more arm dmaengine driver cleanup by
moving code to dmaengine, this time for imx by Javier and pl330 by
Boojin along with the usual driver fixes."
Fix up some fairly trivial conflicts with various other cleanups.
* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (67 commits)
dmaengine: imx: fix the build failure on x86_64
dmaengine: i.MX: Fix merge of cookie branch.
dmaengine: i.MX: Add support for interleaved transfers.
dmaengine: imx-dma: use 'dev_dbg' and 'dev_warn' for messages.
dmaengine: imx-dma: remove 'imx_dmav1_baseaddr' and 'dma_clk'.
dmaengine: imx-dma: remove unused arg of imxdma_sg_next.
dmaengine: imx-dma: remove internal structure.
dmaengine: imx-dma: remove 'resbytes' field of 'internal' structure.
dmaengine: imx-dma: remove 'in_use' field of 'internal' structure.
dmaengine: imx-dma: remove sg member from internal structure.
dmaengine: imx-dma: remove 'imxdma_setup_sg_hw' function.
dmaengine: imx-dma: remove 'imxdma_config_channel_hw' function.
dmaengine: imx-dma: remove 'imxdma_setup_mem2mem_hw' function.
dmaengine: imx-dma: remove dma_mode member of internal structure.
dmaengine: imx-dma: remove data member from internal structure.
dmaengine: imx-dma: merge old dma-v1.c with imx-dma.c
dmaengine: at_hdmac: add slave config operation
dmaengine: add context parameter to prep_slave_sg and prep_dma_cyclic
dmaengine/dma_slave: introduce inline wrappers
dma: imx-sdma: Treat firmware messages as warnings instead of erros
...
Add inline wrappers for device_prep_slave_sg() and device_prep_dma_cyclic()
interfaces to hide new parameter from current users of affected interfaces.
Convert current users to use new wrappers instead of direct calls.
Suggested by Russell King [https://lkml.org/lkml/2012/2/3/269].
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Chanho Min reported that when the boot loader transfers
control to the kernel, there may be pending interrupts
causing the UART to lock up in an eternal loop trying to
pick tokens from the FIFO (since the RX interrupt flag
indicates there are tokens) while in practice there are
no tokens - in fact there is only a pending IRQ flag.
This patch address the issue with a combination of two
patches suggested by Russell King that clears and mask
all interrupts at probe() and clears any pending error
and RX interrupts at port startup time.
We suspect the spurious interrupts are a side-effect of
switching the UART from FIFO to non-FIFO mode.
Cc: Shreshtha Kumar Sahu <shreshthakumar.sahu@stericsson.com>
Reported-by: Chanho Min <chanho0207@gmail.com>
Suggested-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Jong-Sung Kim <neidhard.kim@lge.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In DMA-operated uart, I found that rx data can be taken by the UART
interrupts during the DMA irq handler. pl011_int is occurred just
before it goes inside spin_lock_irq. When it returns to the callback,
DMA buffer already has been flushed. Then, pl011_dma_rx_chars gets
invalid data. So I add check for the residue as the patch bellow.
Signed-off-by: Chanho Min <chanho.min@lge.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
.device_fc is added in struct dma_slave_config recently. All user drivers, which
want DMA to be the flow controller must pass this field as false. As earlier
driver don't look to use this feature, mark it false for now.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Protect against pl011_console_write() and the interrupt for
the console UART running concurrently on different CPUs.
Otherwise the console_write could spin for a long time
waiting for the UART to become not busy, while the other
CPU continuously services UART interrupts and keeps the
UART busy.
The checks for sysrq and oops_in_progress are taken
from 8250.c.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Reviewed-by: Bibek Basu <bibek.basu@stericsson.com>
Reviewed-by: Shreshtha Kumar Sahu <shreshthakumar.sahu@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In present driver, shutdown clears RTS and DTR in CR register. But the
documentation "Documentation/serial/driver" suggests not to disable
RTS and DTR in shutdown(). Also RTS and DTR is preserved between shutdown
and startup calls, i.e. these are restored in startup if they were enabled
while doing shutdown. So that if RTS and DTR are set using pl011_set_mctrl
then it should continue even after shutdown->startup sequence.
For throttling/unthrottling user should call pl011_set_mctrl.
Signed-off-by: Shreshtha Kumar Sahu <shreshthakumar.sahu@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
fixup usage of dma direction by introducing dma_transfer_direction,
this patch moves spi, serial drivers to use new enum
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Alan Cox <alan@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@iki.fi>
This workaround aims to break the deadlock situation
which raises during continuous transfer of data for long
duration over uart with hardware flow control. It is
observed that CTS interrupt cannot be cleared in uart
interrupt register (ICR). Hence further transfer over
uart gets blocked.
It is seen that during such deadlock condition ICR
don't get cleared even on multiple write. This leads
pass_counter to decrease and finally reach zero. This
can be taken as trigger point to run this UART_BT_WA.
Workaround backups the register configuration, does soft
reset of UART using BIT-0 of PRCC_K_SOFTRST_SET/CLEAR
registers and restores the registers.
This patch also provides support for uart init and exit
function calls if present.
Signed-off-by: Shreshtha Kumar Sahu <shreshthakumar.sahu@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
remove invalid location line in each file header after location
moved from driver/char to driver/tty
Signed-off-by: Jovi Zhang <bookjovi@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This piece of code was just slightly different between the DMA
and IRQ paths, in DMA mode we surely shouldn't read more than
256 character either, so factor this out in its own function and
use for both DMA and PIO mode.
Tested on Ux500 and U300.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds an optional RX DMA codepath for the devices that
support this by using the apropriate burst sizes instead of
pulling single bytes.
Includes portions of code written by Russell King during
a PL08x hacking session.
This has been tested on U300 and Ux500.
Tested-by: Jerzy Kasenberg <jerzy.kasenberg@tieto.com>
Tested-by: Grzegorz Sygieda <grzegorz.sygieda@tieto.com>
Tested-by: Marcin Mielczarczyk <marcin.mielczarczyk@tieto.com>
Signed-off-by: Per Forlin <per.friden@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Make Primecell driver probe functions take a const pointer to their
ID tables. Drivers should never modify their ID tables in their
probe handler.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The serial drivers are really just tty drivers, so move them to
drivers/tty/ to make things a bit neater overall.
This is part of the tty/serial driver movement proceedure as proposed by
Arnd Bergmann and approved by everyone involved a number of months ago.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Rogier Wolff <R.E.Wolff@bitwizard.nl>
Cc: Michael H. Warfield <mhw@wittsend.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Anton Vorontsov