* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA/nes: Fix hang with modified FIN handling on A0 cards
RDMA/nes: Change state to closing after FIN
RDMA/nes: Fix double CLOSE event indication crash
RDMA/nes: Write correct register write to set TX pause param
RDMA/cxgb3: Don't exceed the max HW CQ depth
we're using a pointer through a freed command to reset the request,
which has shown up as an oops with slab poisoning:
Reported-by: Tejun Heo <tj@kernel.org>
Reported-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
If we are busy, then we may have woken up the wait_request handler but
not yet serviced it before the hang check fires. So in hang check,
double check that the i915_gem_do_wait_request() is still pending the
wake-up before declaring all hope lost.
Fixes regression with e78d73b16b.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=30073
Reported-and-tested-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The PL022 SPI bus is sometimes used for early stuff like
regulators that need to be present at module_init() time, so
we move this to a subsys_initcall().
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Use netdev_alloc_skb_ip_align() helper and do correct allocation
Tested-by: Abraham Arce <x0066660@ti.com>
Signed-off-by: Abraham Arce <x0066660@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During suspend, the power.completion is expected to be set when a
device has not yet started suspending. Set it on init to fix a
corner case where a device is resumed when its parent has never
suspended.
Consider three drivers, A, B, and C. The parent of A is C, and C
has async_suspend set. On boot, C->power.completion is initialized
to 0.
During the first suspend:
suspend_devices_and_enter(...)
dpm_resume(...)
device_suspend(A)
device_suspend(B) returns error, aborts suspend
dpm_resume_end(...)
dpm_resume(...)
device_resume(A)
dpm_wait(A->parent == C)
wait_for_completion(C->power.completion)
The wait_for_completion will never complete, because
complete_all(C->power.completion) will only be called from
device_suspend(C) or device_resume(C), neither of which is called
if suspend is aborted before C.
After a successful suspend->resume cycle, where B doesn't abort
suspend, C->power.completion is left in the completed state by the
call to device_resume(C), and the same call path will work if B
aborts suspend.
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Changing state to CLOSING when FIN is received causes A0 cards to
hang. Fix this by checking for A0 cards in FIN handling.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When the driver receives an AE for FIN received, it closes the
connection without changing the state of the connection in the
hardware to closing. By changing the state to closing, hardware will
do a normal close sequence.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
During a stress testing in a large cluster, multiple close event are
detected and BUG() is hit in the iWARP core. The cause is that the
active node gave up while waiting for an MPA response from the peer
and tried to close the connection by sending RST. The passive node
driver receives the RST but is waiting for MPA response from the user.
When the MPA accept is received, the driver offloads the connection
and sends a CLOSE event. The driver gets an AE indicating RESET
received and also sends a CLOSE event, hitting a BUG().
Fix this by correcting RESET handling and sending CLOSE events.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Setting TX pause param writes to the wrong register location causing
the adapter to hang. Correct the define used to write the reigster.
Addresses: https://bugs.openfabrics.org/show_bug.cgi?id=2116
Reported-by: Shiri Franchi <shirif@voltaire.com>
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
niu_get_ethtool_tcam_all() assumes that its output buffer is the right
size, and warns before returning if it is not. However, the output
buffer size is under user control and ETHTOOL_GRXCLSRLALL is an
unprivileged ethtool command. Therefore this is at least a local
denial-of-service vulnerability.
Change it to check before writing each entry and to return an error if
the buffer is already full.
Compile-tested only.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a call to of_node_put in the error handling code following a call to
of_find_compatible_node.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
local idexpression x;
expression E,E1;
statement S;
@@
*x =
(of_find_node_by_path
|of_find_node_by_name
|of_find_node_by_phandle
|of_get_parent
|of_get_next_parent
|of_get_next_child
|of_find_compatible_node
|of_match_node
)(...);
...
if (x == NULL) S
<... when != x = E
*if (...) {
... when != of_node_put(x)
when != if (...) { ... of_node_put(x); ... }
(
return <+...x...+>;
|
* return ...;
)
}
...>
of_node_put(x);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
With the introduction of an AMBA PrimeCell per-cell block clock,
the pclk was left on after probe() unless explicitly disabled.
This clock is wired to the same clock on PL022 causing it to stay
always on since.
Fix this up properly by clocking the pclk whenever we want to
write into any PL022 registers and clocking the external clock
whenever we want to transmit messages on the bus.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Tested-by : Kevin Wells <wellsk40@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
When using PIO we have a timeout for the TX and RX FIFOs to ensure that
the data actually gets transferred. Warn if we hit that timeout - it
should never happen, but this makes sure we'll find out if it does.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf, x86: Try to handle unknown nmis with an enabled PMU
perf, x86: Fix handle_irq return values
perf, x86: Fix accidentally ack'ing a second event on intel perf counter
oprofile, x86: fix init_sysfs() function stub
lockup_detector: Sync touch_*_watchdog back to old semantics
tracing: Fix a race in function profile
oprofile, x86: fix init_sysfs error handling
perf_events: Fix time tracking for events with pid != -1 and cpu != -1
perf: Initialize callchains roots's childen hits
oprofile: fix crash when accessing freed task structs
Instead of, wrongly, reusing the 'val' variable, use a dedicated
one for reading the status register.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Fix compilation warning by typecasting the tx_buf pointer.
[I'm not thrilled with resorting to a cast; but I cannot see a better
way to go about this. I don't want to drop the const from struct
spi_transfer ~~glikely]
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
commit 052dc7c45i "spi/dw_spi: conditional transfer mode change"
introduced cs_control code, which has a bug by using bit offset
for spi mode to set transfer mode in control register. Also it
forces devices who don't need cs_control to re-configure the
control registers for each spi transfer. This patch will fix them
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Allow interrupt sharing since exclusive interrupt line for
DW SPI controller is not provided on every platform.
Signed-off-by: Yong Wang <yong.y.wang@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
For small transfers at high speeds the expected transfer time can easily
be well under 1ms, causing the delay in wait_for_xfer() to be only the
dead reckoning fudge factor of 5ms currently included. Experiments on
some of my systems shows that this is marginal for some transfers so
double it to 10ms.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Allow the use of the S3C64xx SPI controller with things like PMICs by
moving the init up to subsys_initcall().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This reverts commit b9421ae8f3.
This warning was so prelevant, even for apparently working machines,
that it was just causing fear, anxiety and panic.
The root cause still remains, so we will add some better debugging when
we focus on fixing it.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=17021
Reported-by: Maciej Rutecki <maciej.rutecki@gmail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This reverts commit 0f3ee801b3.
Enabling LVDS on pipe A was causing excessive wakeups on otherwise idle
systems due to i915 interrupts. So restrict the LVDS to pipe B once more,
whilst the issue is properly diagnosed.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=16307
Reported-and-tested-by: Enrico Bandiello <enban@postal.uv.es>
Poked-by: Florian Mickler <florian@mickler.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Adam Jackson <ajax@redhat.com>
Cc: stable@kernel.org
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: bus speed strings should be const
PCI hotplug: Fix build with CONFIG_ACPI unset
PCI: PCIe: Remove the port driver module exit routine
PCI: PCIe: Move PCIe PME code to the pcie directory
PCI: PCIe: Disable PCIe port services during port initialization
PCI: PCIe: Ask BIOS for control of all native services at once
ACPI/PCI: Negotiate _OSC control bits before requesting them
ACPI/PCI: Do not preserve _OSC control bits returned by a query
ACPI/PCI: Make acpi_pci_query_osc() return control bits
ACPI/PCI: Reorder checks in acpi_pci_osc_control_set()
PCI: PCIe: Introduce commad line switch for disabling port services
PCI: PCIe AER: Introduce pci_aer_available()
x86/PCI: only define pci_domain_nr if PCI and PCI_DOMAINS are set
PCI: provide stub pci_domain_nr function for !CONFIG_PCI configs
* 'for-linus' of git://neil.brown.name/md:
md: resolve confusion of MD_CHANGE_CLEAN
md: don't clear MD_CHANGE_CLEAN in md_update_sb() for external arrays
Move .gitignore from drivers/md to lib/raid6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (26 commits)
pkt_sched: Fix lockdep warning on est_tree_lock in gen_estimator
ipvs: avoid oops for passive FTP
Revert "sky2: don't do GRO on second port"
gro: fix different skb headrooms
bridge: Clear INET control block of SKBs passed into ip_fragment().
3c59x: Remove incorrect locking; correct documented lock hierarchy
sky2: don't do GRO on second port
ipv4: minor fix about RPF in help of Kconfig
xfrm_user: avoid a warning with some compiler
net/sched/sch_hfsc.c: initialize parent's cl_cfmin properly in init_vf()
pxa168_eth: fix a mdiobus leak
net sched: fix kernel leak in act_police
vhost: stop worker only if created
MAINTAINERS: Add ehea driver as Supported
ath9k_hw: fix parsing of HT40 5 GHz CTLs
ath9k_hw: Fix EEPROM uncompress block reading on AR9003
wireless: register wiphy rfkill w/o holding cfg80211_mutex
netlink: Make NETLINK_USERSOCK work again.
irda: Correctly clean up self->ias_obj on irda_bind() failure.
wireless extensions: fix kernel heap content leak
...
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
Staging: wlan-ng: Explicitly set some fields in cfg80211 interface
Staging: octeon: depends on NETDEVICES
Staging: spectra: depend on X86_MRST
Staging: zram: free device memory when init fails
Staging: rt2870sta: Add more device IDs from vendor drivers
staging: comedi das08_cs.c: Fix io_req_t conversion
staging: spectra needs <linux/slab.h>
staging: hv: Fixed lockup problem with bounce_buffer scatter list
staging: hv: Increased storvsc ringbuffer and max_io_requests
staging: hv: Fixed the value of the 64bit-hole inside ring buffer
staging: hv: Fixed bounce kmap problem by using correct index
staging: hv: Fix missing functions for net_device_ops
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: ftdi_sio: Added custom PIDs for ChamSys products
USB: cdc-acm: Fixing crash when ACM probing interfaces with no endpoint descriptors.
USB: cdc-acm: Add pseudo modem without AT command capabilities
USB: cxacru: Use a bulk/int URB to access the command endpoint
usb: serial: mos7840: Add USB IDs to support more B&B USB/RS485 converters.
USB: cdc-acm: Adding second ACM channel support for various Nokia and one Samsung phones
usb: serial: mos7840: Add USB ID to support the B&B Electronics USOPTL4-2P.
USB: ssu100: turn off debug flag
usb: allow drivers to use allocated bandwidth until unbound
USB: cp210x usb driver: add USB_DEVICE for Pirelli DP-L10 mobile.
USB: cp210x: Add B&G H3000 link cable ID
USB: CP210x Add new device ID
USB: option: fix incorrect novatel entries
USB: Fix kernel oops with g_ether and Windows
USB: rndis: section mismatch fix
USB: ehci-ppc-of: problems in unwind
USB: s3c-hsotg: Remove DEBUG define
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
tty: fix tty_line must not be equal to number of allocated tty pointers in tty driver
serial: bfin_sport_uart: restore transmit frame sync fix
serial: fix port type conflict between NS16550A & U6_16550A
MAINTAINERS: orphan isicom
vt: Fix console corruption on driver hand-over.
* 'linux-next' of git://git.infradead.org/ubi-2.6:
UBI: do not oops when erroneous PEB is scheduled for scrubbing
UBI: fix kconfig unmet dependency
UBI: fix forward compatibility
UBI: eliminate update of list_for_each_entry loop cursor
* 'drm-intel-fixes' of git://anongit.freedesktop.org/~ickle/drm-intel: (25 commits)
intel_agp,i915: Add more sandybridge graphics device ids
drm/i915: Enable MI_FLUSH on Sandybridge
agp/intel: Fix cache control for Sandybridge
agp/intel: use #ifdef idiom for intel-agp.h
agp/intel: fix physical address mask bits for sandybridge
drm/i915: Prevent double dpms on
drm/i915: Avoid use of uninitialised values when disabling panel-fitter
drm/i915: Avoid pageflipping freeze when we miss the flip prepare interrupt
drm/i915: Tightly scope intel_encoder to prevent invalid use
drm/i915: Allocate the PCI resource for the MCHBAR
drm/i915/dp: Really try 5 times before giving up.
drm/i915/sdvo: Restore guess of the DDC bus in absence of VBIOS
drm/i915/dp: Boost timeout for enabling transcoder to 100ms
drm/i915: Re-use set_base_atomic to share setting of the display registers
drm/i915: Fix offset page-flips on i965+
drm/i915: Include a generation number in the device info
i915: return -EFAULT if copy_to_user fails
i915: return -EFAULT if copy_to_user fails
agp/intel: Promote warning about failure to setup flush to error.
drm/i915: overlay on gen2 can't address above 1G
...
It causes all kinds of DMA API debugging assertions and
all straight-forward attempts to fix it have failed.
So turn off SG, and we'll tackle making this work
properly in net-next-2.6
Reported-by: Dave Jones <davej@redhat.com>
Tested-by: Dave Jones <davej@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is a simplified version of the original patch from James Courtier-Dutton.
>From: James Courtier-Dutton
>Subject: [PATCH] Fix b44 RX FIFO overflow recovery.
>Date: Wednesday, June 30, 2010 - 1:11 pm
>
>This patch improves the recovery after a RX FIFO overflow on the b44
>Ethernet NIC.
>Before it would do a complete chip reset, resulting is loss of link
>for a few seconds.
>This patch improves this to do recovery in about 20ms without loss of link.
>
>Signed off by: James@superbug.co.uk
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a bug introduced in commit
de84727214
"3c59x: Use fine-grained locks for MII and windowed register access".
vortex_interrupt() holds vp->window_lock over multiple register
accesses to reduce locking overhead. However it also needs to call
vortex_error() sometimes, and that uses the regular functions for
access to windowed registers, which will try to acquire window_lock
again.
Therefore, drop window_lock around the call to vortex_error() and set
the window afterward reacquiring the lock. Since vortex_error() may
call vortex_rx(), which *does* require its caller to hold window_lock,
lift that call up into vortex_interrupt(). This also removes the
potential for calling vortex_rx() on a later-generation NIC.
Reported-and-tested-by: Jens Schüßler <jgs@trash.net> [in Debian's 2.6.32]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The time_before_eq()/time_after_eq() functions operate on unsigned
long and only work if the difference between the two compared values
is smaller than half the range of unsigned long (31 bits on i386).
Some of the variables (slave->jiffies, dev->trans_start, dev->last_rx)
used by bonding store a copy of jiffies and may not be updated for a
long time. With HZ=1000, time_before_eq()/time_after_eq() will start
giving bad results after ~25 days.
jiffies will never be before slave->jiffies, dev->trans_start,
dev->last_rx by more than possibly a couple ticks caused by preemption
of this code. This allows us to detect/prevent these overflows by
replacing time_before_eq()/time_after_eq() with time_in_range().
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We cannot use spinlock when kmalloc is invoked with
GFP_KERNEL flag because it can sleep.
So this patch reviews the usage of spinlock within the
stmmac_resume function avoing this bug.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reported-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit ce17178094.
This commit has been independently bisected a few times as being the cause
of a s2ram failure.
Reported-and-tested-by: Kyle McMartin <kyle@mcmartin.ca>
Reported-and-tested-by: Andy Isaacson <adi@hexapodia.org>
Cc: Zou Nan hai <nanhai.zou@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Commit 409f3499a2 (scsi/sd: remove big
kernel lock) introduced a bug in the sd_release routine. Medium
removal should be allowed when the number of open file references
drops to 0, not when it becomes non-zero.
This patch (as1414) adjusts the test to fix the bug.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
New pci ids for GT2 and GT2+ on desktop and mobile sandybridge,
and graphics device ids for server sandybridge. Also rename original
ids string to reflect GT1 version.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
MI_FLUSH is being deprecated, but still available on Sandybridge.
Make sure it's enabled as userspace still uses MI_FLUSH.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Sandybridge GTT has new cache control bits in PTE, which controls
graphics page cache in LLC or LLC/MLC, so we need to extend the mask
function to respect the new bits.
And set cache control to always LLC only by default on Gen6.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
It should shift bit 39-32 into pte's bit 11-4.
Reported-by:Takashi Iwai <tiwai@suse.de>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Arguably this is a bug in drm-core in that we should not be called twice
in succession with DPMS_ON, however this is still occuring and we see
FDI link training failures on the second call leading to the occassional
blank display. For the time being ignore the repeated call.
Original patch by Dave Airlie <airlied@redhat.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
We were passing garbage values into the panel-fitter control register
when disabling it on Ironlake - those values (filter modes and reserved
MBZ bits) would have then be re-used the next time panel-fitting was
enabled.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
When we miss the flip prepare interrupt, we never get into the
software state needed to restart userspace, resulting in a freeze of a
full-screen OpenGL application (such as a compositor).
Work around this by checking DSPxSURF/DSPxBASE to see if the page flip
has actually happened. If it has, do the work we would have done when
the flip prepare interrupt comes in.
Also, add debugfs information to tell us what's going on (based on the
patch from Chris Wilson attached to bugs.fdo bug #29798).
Signed-off-by: Simon Farnsworth <simon.farnsworth@onelan.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We reset intel_encoder for every matching encoder whilst iterating over
the encoders attached to this crtc when changing mode. As such in a
cloned configuration intel_encoder may not correspond to the correct
is_edp encoder.
By scoping intel_encoder to the loop, not only is the compiler able to
spot this mistake, we also improve readiability for ourselves.
[It might not be a mistake, within this function it is unclear as to
whether it is permissable for eDP to be cloned...]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We were failing when trying to allocate the resource for MMIO of the
MCHBAR because we forgot to specify what type of resource we wanted.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: stable@kernel.org
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Only stop trying if the aux channel sucessfully reports that the
transmission was completed, otherwise try again. On the 5th failure,
bail and report that something is amiss.
This fixes a sporadic failure in reading the EDID for my external panel
over DP.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
If the VBIOS tells us the mapping of the SDVO device onto the DDC bus,
use it. However, if there is no VBIOS available that mapping is
uninitialised and we should fallback to our earlier guess.
Fix regression introduced in b1083333 (which in turn is a fix for the
regression caused by the introduction of this guess, 14571b4).
References:
Bug 29499 - [945GM] Screen disconnected because of missing VBIOS
https://bugs.freedesktop.org/show_bug.cgi?id=29499
Bug 15109 - i945GM fails to detect EDID on DVI port
https://bugzilla.kernel.org/show_bug.cgi?id=15109
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reported-and-tested-by: Paul Neumann <paul104x@yahoo.de>
Cc: Adam Jackson <ajax@redhat.com>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: stable@kernel.org
Adam Hill reported that his Arrandale system required a much longer, up
to 200x500us, wait for the panel to initialise or else modesetting would
fail.
References:
https://bugs.freedesktop.org/show_bug.cgi?id=29141
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reported-and-tested-by: Adam Hill <sidepipeuk@yahoo.co.uk>
i965 uses the Display Registers to compute the offset from the display
base so the new base does not need adjusting when flipping. The older
chipsets use a fence to access the display and so do perceive the
surface as linear and have a single base register which is reprogrammed
using the flip.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Reported-by: Marty Jack <martyj19@comcast.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
copy_to_user() returns the number of bytes remaining to be copied and
I'm pretty sure we want to return a negative error code here.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
copy_to_user returns the number of bytes remaining to be copied, but we
want to return a negative error code here. These are returned to
userspace.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Make sure we always detect when we fail to correctly allocate the Isoch
Flush Page and print an error to warn the user about the likely memory
corruption that will result in invalid rendering or worse.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
So set the coherent dma mask accordingly. This dma mask is only used
for physical objects, so it won't really matter allocation-wise.
Now this never really surfaced because sane 32bit kernels only have 1G
of lowmem. But some eager testers (distros?) still carry around the patch
to adjust lowmem via a kconfig option. And the kernel seems to favour
high allocations on boot-up, hence the overlay blowing up reliably.
Because the patch is tiny and nicely shows how broken gen2 is it's imho
worth to merge despite the fact that mucking around with the lowmem/
highmem division is (no longer) supported.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=28318
Cc: stable@kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The vblank status bit is a sticky bit that must be cleared with a write
of '1' prior to polling for the next vblank.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Sitsofe Wheeler <sitsofe@yahoo.com>
jbarnes: I'd still rather see a lock, but I think you're right that
we don't generally wait in code that needs not to miss an interrupt.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Partial revert of 9d0498a2bf.
Signed-off-by: Pekka Enberg <penberg@kernel.org>
Tested-by: Hugh Dickins <hughd@google.com>
Tested-by: Sven Joachim <svenjoac@gmx.de>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This fixes blur-like screen corruption on the following card:
VGA compatible controller [0300]: Intel Corporation 82G33/G31 Express
Integrated Graphics Controller [8086:29c2] (rev 10)
intel_sdvo_mode_set() should not return prematurely just because some
features are not supported.
https://bugzilla.kernel.org/show_bug.cgi?id=17151
Signed-off-by: Pavel Roskin <proski@gnu.org>
Reported-by: Jonathan Corbet <corbet@lwn.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[ickle: Relax a couple more checks for failing LVDS modesetting]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This reverts commit 86f100b136.
The kref API requires the handlecount to be initialised to one on object
creation (so that kref_get() doesn't complain upon first use) so the
dalliance in the drivers is required in order to sink the initial
floating reference.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
drivers/gpu/drm/i915/intel_overlay.c: In function 'intel_overlay_print_error_state':
drivers/gpu/drm/i915/intel_overlay.c:1467: error: implicit declaration of function 'seq_printf'
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=16811
Reported-by: Martin Ziegler <ziegler@uni-freiburg.de>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Eric Anholt <eric@anholt.net>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Andre Muller <andremuellerster@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Only fallback to a set of default modes on a connector iff that
connector is known to be connected. The issue occurs that with limited
hardware which cannot probe a connector and so reports the
connector status as unknown will then attempt to retrieve the modes for
it during drm_helper_probe_single_connector_modes(). Should that fail,
the helper then generates a default set which fools the fb_helper and
causes havoc with the console and beyond.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Polling for a VGA device on an old system can be quite expensive,
causing latencies on the order of 600ms. As we hold the mode mutex for
this time and also need the same mutex to move the cursor, we trigger a
user-visible stall.
The real solution would involve improving the granulatity of the
locking and so perhaps performing some of the probing not under the lock
or some other updates can be done under different locks. Also reducing the
cost of probing for a non-existent monitor would be worthwhile. However,
exposing a parameter to disable polling is a simple workaround in the
meantime.
In order to accommodate users turning polling on and off at runtime, the
polling is potentially re-enabled on every probe. This is coupled to
the user calling xrandr, which seems to be a vaild time to reset the
polling timeout since the information on the connection has just been
updated. (The presumption being that all connections are probed in a
single xrandr pass, which is currently valid.)
References:
Bug 29536 - 2.6.35 causes ~600ms latency every 10s
https://bugs.freedesktop.org/show_bug.cgi?id=29536
Bug 16265 - Why is kslowd accumulating so much CPU time?
https://bugzilla.kernel.org/show_bug.cgi?id=16265
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reported-and-tested-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
digital underscan support regressed tv-out.
fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=29985
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
These VGT regs need to be programmed via the ring rather than
MMIO as on previous asics (r6xx/r7xx).
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
vhost should set worker to NULL on cgroups attach failure,
so that we won't try to destroy the worker again on close.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Since 2.6.36-rc1, non-root users of vhost-net fail to attach
if they are in any cgroups.
The reason is that when qemu uses vhost, vhost wants to attach
its thread to all cgroups that qemu has. But we got the API backwards,
so a non-priveledged process (Qemu) tried to control
the priveledged one (vhost), which fails.
Fix this by switching to the new cgroup_attach_task_all,
and running it from the vhost thread.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
For ISP82xx, the check for empty slot in request queue before posting command type 6
request was missing. This could lead to request queue entry corruptions causing
IO timeouts.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Currently, if target sets the SCSI Status (with Check condition)
and there is no FCP residual bit set then driver does not check
for dropped frame. This could lead to data corruption.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The fw_hung flag should be set ir-respective of if there is a
mbx command pending or not. Also the complete should be called
if there is a mbx waiting.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The seconds_since_last_heartbeat should be checked for consecutive
heartbeat checks. Currently it could happen that seconds_since_last_heartbeat
gets set to max (2 seconds) for non-consecutive heartbeat checks.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The cfg80211 api has introduced a few new fields. Rather than assume
what cfg80211 api does by default, set these explicitly.
Signed-off-by: Karl Relton <karllinuxtest.relton@ntlworld.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
lld_nand fails to build on arches without virt_to_bus. Since this driver
is specifically for hardware enablment on Moorestown, this patch adds
Moorestown MID support as a dependency.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Taken from DPO_RT3070_LinuxSTA_V2.3.0.4_20100604.tar.bz2 and
2010_0709_RT2870_Linux_STA_v2.4.0.1.tar.bz2, with duplicates removed.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 90abdc3b9 converted all PCMCIA users away from io_req_t. In
das08_cs.c the converted IO lines mask setting was added but the old
line using the now inexistent p_dev->io was not removed.
Signed-off-by: Andreas Bombe <aeb@debian.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On one of my m68k test builds I get:
drivers/staging/spectra/ffsport.c: In function ‘ioctl_read_page_data’:
drivers/staging/spectra/ffsport.c:196: error: implicit declaration of function ‘kmalloc’
drivers/staging/spectra/ffsport.c:196: warning: assignment makes pointer from integer without a cast
drivers/staging/spectra/ffsport.c:212: error: implicit declaration of function ‘kfree’
drivers/staging/spectra/ffsport.c: In function ‘ioctl_write_page_data’:
drivers/staging/spectra/ffsport.c:229: warning: assignment makes pointer from integer without a cast
drivers/staging/spectra/ffsport.c: In function ‘SBD_setup_device’:
drivers/staging/spectra/ffsport.c:637: warning: assignment makes pointer from integer without a cast
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Pekka Enberg <penberg@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixed lockup problem with bounce_buffer scatter list which caused
crashes in heavy loads. And minor code indentation cleanup in effected
area.
Removed whitespace and noted minor indentation changes in description as
pointed out by Joe Perches. (Thanks for reviewing Joe)
Signed-off-by: Hank Janssen <hjanssen@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Increased storvsc ringbuffer and max_io_requests. This now more
closely mimics the numbers on Hyper-V. And will allow more IO requests
to take place for the SCSI driver.
Max_IO is set to double from what it was before, Hyper-V allows it and
we have had appliance builder requests to see if it was a problem to
increase the number.
Ringbuffer size for storvsc is now increased because I have seen A few buffer
problems on extremely busy systems. They were Set pretty low before.
And since max_io_requests is increased I Really needed to increase the buffer
as well.
Signed-off-by:Hank Janssen <hjanssen@microsoft.com>
Signed-off-by:Haiyang Zhang <haiyangz@microsoft.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixed the value of the 64bit-hole inside ring buffer, this
caused a problem on Hyper-V when running checked Windows builds.
Checked builds of Windows are used internally and given to external
system integrators at times. They are builds that for example that all
elements in a structure follow the definition of that Structure. The bug
this fixed was for a field that we did not fill in at all (Because we do
Not use it on the Linux side), and the checked build of windows gives
errors on it internally to the Windows logs.
This fixes that error.
Signed-off-by:Hank Janssen <hjanssen@microsoft.com>
Signed-off-by:Haiyang Zhang <haiyangz@microsoft.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixed bounce offset kmap problem by using correct index.
The symptom of the problem is that in some NAS appliances this problem
represents Itself by a unresponsive VM under a load with many clients writing
small files.
Signed-off-by:Hank Janssen <hjanssen@microsoft.com>
Signed-off-by:Haiyang Zhang <haiyangz@microsoft.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix missing functions for net_device_ops.
It's a bug when porting the drivers from 2.6.27 to 2.6.32. In 2.6.27,
the default functions for Ethernet, like eth_change_mtu(), were assigned
by ether_setup(). But in 2.6.32, these function pointers moved to
net_device_ops structure and no longer be assigned in ether_setup(). So
we need to set these functions in our driver code. It will ensure the
MTU won't be set beyond 1500. Otherwise, this can cause an error on the
server side, because the HyperV linux driver doesn't support jumbo frame
yet.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Hank Janssen <hjanssen@microsoft.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Added the 0xDAF8 to 0xDAFF PID range for ChamSys limited USB interface/wing products
Signed-off-by: Luke Lowrey <luke@chamsys.co.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Certain USB devices, such as the Nokia X6 mobile phone, don't expose any
endpoint descriptors on some of their interfaces. If the ACM driver is forced
to probe all interfaces on a device the a NULL pointer dereference will occur
when the ACM driver attempts to use the endpoint of the alternative settings.
One way to get the ACM driver to probe all the interfaces is by using the
/sys/bus/usb/drivers/cdc_acm/new_id interface.
This patch checks that the endpoint pointer for the current alternate settings
is non-NULL before using it.
Signed-off-by: Toby Gray <toby.gray@realvnc.com>
Cc: Oliver Neukum <oliver@neukum.name>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
cdc-acm.c : Manage pseudo-modem without AT commands capabilities
Enable to drive electronic simple gadgets based on microcontrolers.
The Interface descriptor is like this:
bInterfaceClass 2 Communications
bInterfaceSubClass 2 Abstract (modem)
bInterfaceProtocol 0 None
Signed-off-by: Philippe Corbes <philippe.corbes@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The command endpoint is either a bulk or interrupt endpoint, but using
the wrong type of transfer causes an error if CONFIG_USB_DEBUG is
enabled after commit f661c6f8c6, which
checks for this mismatch.
Detect which type of endpoint it is and use a bulk/int URB as
appropriate. There are other function calls specifying a bulk pipe,
but usb_clear_halt doesn't use the pipe type (only the endpoint) and
usb_bulk_msg auto-detects interrupt transfers.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Cc: stable <stable@kernel.org> [.34 and newer]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add the USB IDs needed to support the B&B USOPTL4-4P, USO9ML2-2P, and
USO9ML2-4P. This patch expands and corrects a typo in the patch sent
on 08-31-2010.
Signed-off-by: Dave Ludlow <dave.ludlow@bay.ws>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
S60 phones from Nokia and Samsung expose two ACM channels. The first is a modem
with a standard AT-command interface, which is picked up correctly by CDC-ACM.
The second ACM port is marked as having a vendor-specific protocol. This means
that the ACM driver will not claim the second channel by default.
This adds support for the second ACM channel for the following devices:
Nokia E63
Nokia E75
Nokia 6760 Slide
Nokia E52
Nokia E55
Nokia E72
Nokia X6
Nokia N97 Mini
Nokia 5800 Xpressmusic
Nokia E90
Samsung GTi8510 (INNOV8)
Signed-off-by: Toby Gray <toby.gray@realvnc.com>
Cc: Oliver Neukum <oliver@neukum.name>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add the USB ID needed to support B&B Electronic's 2-port, optically-isolated,
powered, USB to RS485 converter.
Signed-off-by: Dave Ludlow <dave.ludlow@bay.ws>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Linus Torvalds